Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall ................................................................................................................................................4

Installation to Solid Concrete and Cinder Block .....................................................................................................................5

Mounting Flat Panel Screen with VESA hole pattern ......................................................................................................... 6,7

Mounting Flat Panel Screen with Peerless PLP model adapter plate (PLP adapter plates are not UL listed) .......................7

Tools Needed for Assembly

• stud nder ("edge to edge" stud nder is recommended) • 3/8" socket wrench (3/8" extended driver is

recommended) • phillips screwdriver • drill • 5/16" bit for concrete and cinder block wall • 5/32" bit for wood stud

wall • level • 6 mm allen wrench (if attaching to PLP models)

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud nder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

• Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit

- ACC415;

• Brick Contact Qualied Professional

• Other or unsure? Contact Qualied Professional

WARNING

3 of 10 ISSUED: 01-17-12 SHEET #: 125-9277-1

Description Qty. Part #

Awallmountassembly 1 201‐1967

Blockingtab 1 200‐1871

C.219IDx.5ODx.125Hspacer 1 540‐1032

D#14x2‐1/2"hexheadwoodscrew 4 5S1‐015‐C03

Econcreteanchor 4 590‐0320

F18"polyestermeshsleeve2 600‐1014

Gcabletie 4 560‐9711

HM10x15mmsocketheadscrew 4 520‐9262

I.198x.313x.437Hretainingspacer 4 590‐5005

J4mmsecurityallenwrench 1 560‐1146

AA M5x10mmsocketpinscrew 5 520‐1063

BB M4x12mmsocketpinscrew 4 510‐1079

CC M4x20mmsocketpinscrew 4 510‐1061

DD M5x40mmsocketpinscrew 1 510‐1001

EE 1/4"flatwasher4 540‐9440

FF M6x12mmsocketpinscrew 4 520‐1050

GG M8x15mmsocketpinscrew4 520‐1068

Parts List

1Snap installation tab off of wall mount assembly (A).

INSTALLATION TAB

CC DD

Some parts may appear slightly different than illustrated.

AA BB

EE FF GG

4 of 10 ISSUED: 01-17-12 SHEET #: 125-9277-1

Installation to Wood Stud Wall

CL = stud centerline

Using a stud nder, locate the edges of the wood studs used in mounting this product. Use of an edge-to-edge stud

nder is highly recommended. Based on its edges and using a level, draw a vertical line down the center of each

stud. Mark a point (point 1) on the right stud centerline where upper right slot will be located. Using a level, mark a

point (point 2) on the left stud centerline level with point 1 as shown in gure 2.1. Drill 5/32" diameter holes 2-1/2"

deep through studs at the two points. Loosely fasten wall mount assembly (A) to wall using two #14 x 2-1/2" wood

screws (D) as shown in gure 2.2. Level, hold, and then tighten screws.

Mark two more points for bottom slots on the right and left stud centerlines. Drill 5/32" diameter holes 2-1/2" deep

through studs at the two points. Using two #14 x 2-1/2" wood screws, fasten bottom of wall mount assembly to wall

as shown in gure 2.3.

Skip to step 3 on page 6.

g 2.1

POINT 1

POINT 2

g 2.3

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is rmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud nder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations.

WARNING

g 2.2

5 of 10 ISSUED: 01-17-12 SHEET #: 125-9277-1

Position wall mount assembly (A) at desired position

on wall. Use wall mount assembly, making sure that

it is level, as a template to mark holes. Drill four

5/16" (8mm) dia. holes to a minimum depth of 2-1/2"

(64 mm). Concrete must be 2000 psi density

minimum. Insert anchors (E) in holes ush with wall

as shown in gure 2.4. Place wall mount assembly

over anchors and secure with #14 x 2-1/2" wood

screws (D) as shown in gure 2.5. Make sure wall

plate is level and tighten all fasteners.

Installation to Solid Concrete and Cinder Block Wall

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a

solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90

specications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

WARNING

g 2.5

SOLID

CONCRETE CINDER

BLOCK

Drill holes and insert anchors (E).

Place plate (A) over anchors (E) and secure with screws (D).

Tighten all fasteners.

concrete

surface

• Tighten wood screws so that wall plate is rmly at-

tached, but do not overtighten. Overtightening can

damage screws, greatly reducing their holding power.

• Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

• Always attach concrete expansion anchors directly

to load-bearing concrete.

• Never attach concrete expansion anchors to con-

crete covered with plaster, drywall, or other nishing

material. If mounting to concrete surfaces covered

with a nishing surface is unavoidable, the nishing

surface must be counterbored as shown below. If

plaster/drywall is thicker than 5/8", custom fasteners

must be supplied by installer.

WARNING

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

dry wall

plaster/

dry wall

concrete concrete

g 2.4

6 of 10 ISSUED: 01-17-12 SHEET #: 125-9277-1

INSTALLATION TAB

SLIDING ARM

Place installation tab over sliding arms of wall mount assembly (A) to lock them in place.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not

tightly secured, damage may occur to screen or product may fail. Contact customer care for correct hardware to

use.

WARNING

Find the VESA® hole pattern as shown below, and attach screen to mounting plate as specied below. Verify that all

holes are properly aligned, and then tighten screws. If using security screws,

tighten using security allen wrench (M).

VESA 100 x 100 VESA 200 x 100

FOR VESA 100 MOUNTING PATTERN:

Thread two M4 x 12 mm screws (BB), leaving .25" exposed thread, into top holes on back of screen. Hook screen

onto mounting plate, and attach using bottom two M4 x 12 mm screws as shown in gures 4.4 and 4.5. (page 8)

Tighten all four screws.

Note: If screw (BB) is too small to engage threaded inserts, attach mounting plate to back of screen using

four M5 x 10 mm screws (AA).

VESA 200 x 200

7 of 10 ISSUED: 01-17-12 SHEET #: 125-9277-1

DETAIL 2

Figure 4.1

FOR VESA 200 mm x 200 mm MOUNTING PATTERN:

Thread two M6 x 12 mm socket pin screws (FF) with 1/4" at washers (EE) or M8 x 12 mm socket pin screws (GG),

leaving .25" exposed thread, into top holes on back of screen as shown in gure 4.1.

Hook screen onto mounting plate slots, and attach using two bottom M6 x 12 mm socket pin screws (FF) with 1/4"

at washers (EE) or M8 x 12 mm socket pin screws (GG) as shown in gures 4.2 and 4.3. Tighten all four screws.

NOTE: Only use 1/4" at washers (EE) with M6 x 12 mm socket pin screws (FF).

1/8"

DISPLAY DISPLAY

DISPLAY

TOP SLOT

MOUNTING PLATE

Figure 4.2

Figure 4.3

MOUNTING PLATE

FF or GG

NOTE: Only use 1/4" at washers (EE) with

M6 x 12 mm socket pin screws (FF).

DETAIL 1

8 of 10 ISSUED: 01-17-12 SHEET #: 125-9277-1

FOR VESA 200 MOUNTING PATTERN:

Thread two M4 x 12 mm screws (BB), leaving .25" exposed thread, into top holes on back of screen. Hook screen onto

mounting plate, and attach using two bottom M4 x 12 mm screws as shown in gures 4.4 and 4.5. Tighten all four screws.

FOR SCREENS WITH VESA MOUNTING PATTERN IN A POCKET:

Thread two retaining spacers (I) onto two M4 x 20 mm screws (CC), leaving .25" exposed thread as shown in gure 4.6.

Thread M4 x 20 mm screws with retaining spacers into top holes on back of screen. Hook screen onto mounting plate,

and attach using bottom two M4 x 20 mm screws and retaining spacers as shown in gures 4.4 and 4.5. Tighten all four

screws.

MOUNTING PLATE

(NOTE: MOUNTING PLATE

SHOWN WITHOUT FULL

WALL MOUNT ASSEMBLY

FOR CLARITY) g. 4.4 g. 4.5

MOUNTING PLATE

(NOTE: MOUNTING PLATE

SHOWN WITHOUT FULL

WALL MOUNT ASSEMBLY

FOR CLARITY)

Note: Flat panel screen

may appear slightly dif-

ferent than illustrated.

For screens with a hole

pattern in a pocket,

spacers (L) go between

mounting plate and

screen.

g. 4.6

GENERIC

ADAPTER

BRACKET

FOR INSTALLING TO PEERLESS PLP MODEL ADAPTER BRACKET (not UL listed)

Note: Refer to PLP model adapter bracket instruction sheet for attachment of adapter bracket to screen.

Thread two M10 x 15 mm screws (H), leaving .25" exposed thread, into top holes on back of screen. Hook screen

onto mounting plate, and attach using two bottom M10 x 15 mm screws as shown in gures 5.1 and 5.2. Tighten

screws using 6 mm allen wrench (not included).

For screen compatibility please refer to the plasma interface list on our website www.peerlessmounts.com or

call customer care for a screen specic adapter bracket (PLP models).

GENERIC ADAPTER

BRACKET

MOUNTING PLATE

g. 5.1 g. 5.2

MOUNTING PLATE

(NOTE: MOUNTING PLATE

SHOWN WITHOUT FULL

WALL MOUNT ASSEMBLY

FOR CLARITY)

9 of 10 ISSUED: 01-17-12 SHEET #: 125-9277-1

5° tilt 10° tilt

M6 SCREW

MOUNTING

PLATE

Slide one mesh sleeve (F) over each cable. Use

cable ties (G) to tighten both ends of mesh sleeves

to cables.

Note: Loop cable ties through cable mounts and

tighten cable and mesh sleeve to cable mounts.

CABLE MOUNTS

Optional: To lock mount in closed position, insert

one M5 x 40 mm screw (DD) into tapped hole in

either top or bottom of at plate.

Note: Screen not shown for clarity.

FLAT

PLATE

TAPPED HOLE

Screen can tilt 5° or 10° forward.

Note: Screen must be securely attached to mounting plate with all fasteners before adjusting tilt.

To tilt screen 5° forward, lift and pull mounting plate forward until middle notch rests on M6 screw as shown in gure

8.1. Tighten M6 screw (both sides) and M10 screws (both sides).

To tilt screen 10° forward, lift and pull mounting plate forward until rear notch rests on M6 screw as shown in gure

8.2. Tighten M6 screw (both sides) and M10 screws (both sides).

Note: For security models, tighten M6 screw using security allen wrench (J). For all M10 screws, use 6 mm allen

wrench (not included).

M10 SCREW

0° tilt

DETAIL 3

10 of 10 ISSUED: 01-17-12 SHEET #: 125-9277-1

Roll can be adjusted 1° clockwise or

counterclockwise.

To adjust roll, loosen screen fasteners slightly,

leaving them snug. Level screen, then tighten screen

fasteners.

NOTE: When adjusting roll, screws should be

retightened as indicated in step 4.

Optional: To lock one sliding arm of mount in place,

slide locking tab (B) over top or bottom of sliding arm

and attach to mount using one M5 x 10 mm screw

(AA) and one spacer (C).

Note: Screen not shown for clarity.

SLIDING ARM

SCREEN FASTENER