Peerless WL-SR560M-300 User Manual
Displayed below is the user manual for WL-SR560M-300 by Peerless which is a product in the Multimedia Carts & Stands category. This manual has pages.
Related Manuals
2016-11-17 #180-9092-2 2016-12-06
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
Installation and Assembly:
Install prior to attaching adapter brackets to TV
Models: WL-SR560M-300
2 of 11 2016-11-17 #180-9092-2 2016-12-06
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List........................................................................................................................................................................ 3, 4, 5
Wireless Receiver Assembly and Power Module Assembly Installation...............................................................................11
Installing Adapter Brackets ................................................................................................................................................. 12
Wireless Receiver Assembly and Power Module Assembly Setup.......................................................................................15
Cord Management ............................................................................................................................................................... 18
Tools Needed for Assembly
• phillips screwdriver
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, and fully understands
these instructions.
• Never exceed the Maximum Load Capacity on page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• The cart is not affi xed or secured to the fl oor, and may therefore tip over and/or fall if screen and/or stand is shaken
or hit. Always monitor children and do not let children play alone around stand as they could get hurt by a falling
screen. Not recommended for use in areas with heavy traffi c.
WARNING
3 of 11 2016-11-17 #180-9092-2 2016-12-06
ISSUED: 06-12-12 SHEET #: 180-9023-1
User Manual and Installation Guide
Pro Wireless Multimedia Kit
Models:
HDS200
HDS200-2
HDS200-3
HDS200-4 READY
®
Step 7 While turning on the display device the HD Flow Pro Wireless Multimedia units will be going through the startup process. This process may
take up to two minutes to complete. The Power/Link indicator lights on the Transmitter and the Receiver will be flashing at first. Flashing indicates
that the units are establishing a secure connection. Wait until the connection is successfully established, indicated by the Power/Link indicator
light becoming solid.
Minutes
2
1 x Transmitter
1 x Receiver
2 x Stand
1 x Remote Control
1 x IR Flasher
1 x IR Extender
1 x Component Adaptor
2 x Power Adapter
1 x Quick Start Guide
1 x Users Manual
Step 2 Connect the provided IR Flasher to the IR-OUT port on the Transmitter.
Find the location of the IR window on your source device and adhere the
IR Flasher eye directly over the IR window on your source device.
NOTE: One IR Flasher eye is to be used for one component device.
Step 4 Install the IR Extender by plugging in the provided IR Extender in to
the IR-IN port on the Receiver and adhering the other end of the IR Extender
to a vertical surface near the output device. Ensure that the IR Extender is in
a line of sight to the remote control that controls your source devices.
NOTE: For Multicast models, receivers two, three and four do not come with an IR Ex tender. Additional IR E xtenders
(HDS-IRE) can be purchased separately; visit peerless-av.com for more inform ation.
Step 6 Turn on your display device (TV, monitor, projector, etc.).
Step 3 Connect the display device (TV, monitor, projector, etc.)
to the Receiver.
Step 5 Power-up the HD Flow Pro Devices.
1. Plug in the power adapter for the Transmitter and the Receiver to nearby
available power outlets.
2. Plug in the power adapter end to the Transmitter and then to the Receiver.
3. The units will automatically turn-on. The average power-on/sync time
is approximately t wo minutes.
What’s in the Box
Installation and Setup
Troubleshooting Tips
Tip The IR window
may be easier to
locate with a direct
light shining on
sections of the
front panel of the
component device.
A small flashlight
works well.
Power/Source
Selection Button
Tip Repeat Steps
3-11 to connect
more than one
Receiver unit
(HDS200-2,
HDS200-3,
HDS200-4).
Step 1 Connect the Transmitter to the source devices
(Blu-ray™ Disc player, set top box, gaming console, etc.).
Step 9 Turn on the desired source device that is connected to
the Transmitter.
Step 11 Play the source device content and enjoy up to Full HD 1080p
wireless entertainment experience.
• Check the media source resolution. The display device must be able
to support the resolution of the media source that is being streamed.
Utilizing the INFO button will allow you to see the resolution data that
the display device supports. If the display device supports the highest
resolution of 720p but the source device is outputting 1080p content,
the content needs to be down-scaled to the maximum resolution of the
display device, in this case 720p.
Receiver Output Indicator Light Blinks:
• Make sure that your display device, source device and the HD Flow Pro units
are all turned ON and the Receiver is properly connected to the output device.
• Verify that the Receiver is set to the appropriate output port.
• Check the resolution setting of your source device. This may need to be
changed to a resolution supported by the HD Flow Pro unit. Reference
the Resolution Chart in the HD Flow Pro Manual for compatibility.
Reference your source devices’ manual for instruction on changing
the output resolution.
If the above troubleshooting tips do not resolve the issues for a unicast setup,
please reference the Factory Reset Section of the HD Flow Pro Manual. For a
multicast system configuration, please contact Peerless-AV Customer Care at
800-856-2112 for further instruction.
Step 8 Select the output that connects the Receiver to the display using
the Power/Source Selection Button or the provided remote control.
The output indicator light will become solid and the HD Flow logo will
appear on the display device.
Step 10 Select the desired source or device input on the Transmitter
using the Power/Source Selection Button on the remote control.
Transmitter and/or Receiver Indicator Lights are all Blinking:
• The HD Flow Pro units are establishing a connection. It can take
up to two minutes for the HD Flow Pro units to establish a complete
connection. If after two minutes have passed and the units have not
established a connection, unplug the power cable, wait 30 seconds
and reconnect the power supply to the units.
Transmitter or Receiver Power Indicator Light is OFF:
• Check and verify the power supply connection.
Transmitter Input Indicator Light Blinks:
• Make sure that your source device is turned ON and the cable
is properly connected.
• Verify that the Transmitter is set to the appropriate input port.
• Check the resolution from your source device. This may need to
be changed to a resolution supported by the HD Flow Pro Wireless
Multimedia Kit. Reference the Resolution Chart in the HD Flow Pro
Manual for compatibility. Reference your source devices’ manual
for instruction on changing the output resolution.
Receiver Power Indicator Light Blinks:
• Verify that the HD Flow Pro Transmitter and Receiver are within
the recommended range of 131 feet. Physical obstructions such as
walls, floors and ceilings between the Transmitter and Receiver may
decrease the strength of the connection signal and reduce the overall
transmission range.
If a connection has been established and the HD Flow logo can be seen
on the display device, but content is not playing:
• Make sure that the input/output cables are properly connected.
• Verify that the Transmitter is set to the appropriate input port.
Warning Do not place the HD Flow
Pro units near other devices that
emit excessive amounts of heat.
Increased temperatures may
cause the HD Flow Pro Transmitter
or Receiver unit to malfunction
or stop working.
tthdi l d i (TV it j t t )
S
teps
ect
ne
t
Quick Start Guide for HD Flow Pro Wireless Multimedia Kit - LIT-090 6
Power/Source
Selection Button
© 2012 Peerless Industries, Inc. Peerless-AV™ is a tradema rk of Peerless I ndustries , Inc. All righ ts reserv ed.
HD Flow™ is a trademark of I Do It, LTD. Other parties’ marks are the proper ty of their res pective own ers. hdflow.com
Quick Start Guide
PRO WIRELESS MULTIMEDIA KIT
Model No. HDS200 (-2, -3, -4)
READY
®
Parts List Part #
Description Qty
AA wireless receiver assembly 1 180-1327
BB power module assembly 1 180-1015
CC enclosure mounting bracket small 4 120-1195
DD enclosure mounting bracket large 4 120-1196
EE lock nut 1/4-20 8 530-1021
FF cable tie anchor 2 590-9469
GG cable tie large 8 590-1168
HH cable tie small 2 560-9711
II 1/4-20 x 12mm decorative screw 8 520-2325
JJ cable management sheath 1 590-9468
KK 4 mm allen wrench 1 560-9646
II
GG
HH
KK
EE FF
CC
DD
BB
AA JJ
Additional Wireless Components
wireless transmitter (1)wireless Receiver (1)
component/composite
to VGA dongle (1) IR Extender (1)
remote (1)
ir fl asher (1)
plastic stand (1)
instruction sheet (1)12v power adapter (2)
3v battery (1) install guide (1)
hdmi cable (2)
ISSUED: 12-22-14 SHEET #: 180-9064-1
User Manual and Installation Guide
Models:
HDS300
HDS300-2
HDS300-3
HDS300-4
HDS300-5
HDS300-6 READY
®
Powered by
P
owere
d
b
y
Step 7 While turning on the display device the PeerAirTM Pro Wireless AV Multi-Display System will be going through the startup process. This
process may take up to 45 seconds to complete. The Power/Link indicator lights on the Transmitter and the Receiver will be fl ashing at fi rst.
Flashing indicates that the units are establishing a secure connection. Wait until the connection is successfully established, indicated by the
Power/Link indicator light becoming solid.
1 x Transmitter
1 x Receiver
2 x Stand
1 x Remote Control
1 x IR Flasher
1 x IR Extender
1 x Component Adaptor
2 x Power Adaptor
1 x Quick Start Guide
1 x Users Manual
Step 2 Connect the provided IR Flasher to the IR-OUT port on the Transmitter.
Find the location of the IR window on your source device and adhere the
IR Flasher eye directly over the IR window on your source device.
NOTE: One IR Flasher eye is to be used for one component device.
Step 4 Install the IR Extender by plugging in the provided IR Extender in to
the IR-IN port on the Receiver and adhering the other end of the IR Extender
to a vertical surface near the output device. Ensure that the IR Extender is in
a line of sight to the remote control that controls your source devices.
NOTE: For Multicast models, receivers two through six do not come with an IR Ex tender. Additional IR E xtenders (HDS-
IRE) can be purchased separately; visit peerless-av.com for more infor mation.
Step 6 Turn on your display device (TV, monitor, projector, etc.).
Step 3 Connect the display device (TV, monitor, projector, etc.)
to the Receiver.
Step 5 Power-up the PeerAirTM Pro Devices.
1. Plug in the power adaptor for the Transmitter and the Receiver to nearby
available power outlets.
2. Plug in the power adaptor end to the Transmitter and then to the Receiver.
3. The units will automatically turn-on. The average power-on/sync time
is approximately 45 seconds.
What’s in the Box
Installation and Setup
Troubleshooting Tips
Tip The IR window
may be easier to
locate with a direct
light shining on
sections of the
front panel of the
component device.
A small fl ashlight
works well.
Power/Source
Selection Button
Step 1 Connect the Transmitter to the source devices
(Blu-ray™ Disc player, set top box, gaming console, etc.).
Step 9 Turn on the desired source device that is connected to
the Transmitter.
Step 11 Play the source device content and enjoy up to Full HD 1080p
wireless entertainment experience.
• Check the media source resolution. The display device must be able
to support the resolution of the media source that is being streamed.
Utilizing the INFO button will allow you to see the resolution data that
the display device supports. If the display device supports the highest
resolution of 720p but the source device is outputting 1080p content,
the content needs to be down-scaled to the maximum resolution of the
display device, in this case 720p.
Receiver Output Indicator Light Blinks:
• Make sure that your display device, source device and the
PeerAirTM Pro
units
are all turned ON and the Receiver is properly connected to the output device.
• Verify that the Receiver is set to the appropriate output port.
• Check the resolution setting of your source device. This may need to be
changed to a resolution supported by the
PeerAirTM Pro
unit. Reference
the Resolution Chart in the
PeerAirTM Pro
Manual for compatibility.
Reference your source devices’ manual for instruction on changing
the output resolution.
If the above troubleshooting tips do not resolve the issues for a unicast setup,
please reference the Factory Reset Section of the PeerAirTM Pro Manual. For a
multicast system configuration, please contact Peerless-AV Customer Care at
800-865-2112 for further instruction.
Step 8 Select the output that connects the Receiver to the display using
the Power/Source Selection Button or the provided remote control.
The output indicator light will become solid and the HD Flow logo will
appear on the display device.
Step 10 Select the desired source or device input on the Transmitter
using the Power/Source Selection Button or the remote control.
Transmitter and/or Receiver Indicator Lights are all Blinking:
• The PeerAirTM Pro units are establishing a connection. It can take
up to 45 seconds for the PeerAirTM Pro units to establish a complete
connection. If two minutes have passed and the units have not
established a connection, unplug the power cable, wait 30 seconds
and reconnect the power supply to the units.
Transmitter or Receiver Power Indicator Light is OFF:
• Check and verify the power supply connection.
Transmitter Input Indicator Light Blinks:
• Make sure that your source device is turned ON and the cable
is properly connected.
• Verify that the Transmitter is set to the appropriate input port.
• Check the resolution from your source device. This may need to be
changed to a resolution supported by the PeerAirTM Pro Wireless
AV Multi-Display System. Reference the Resolution Chart in the
PeerAirTM Pro Manual for compatibility. Reference your source
devices’ manual for instruction on changing the output resolution.
Receiver Power Indicator Light Blinks:
• Verify that the
PeerAirTM Pro
Transmitter and Receiver are within
the recommended range of 210 feet. Physical obstructions such as
walls, fl oors and ceilings between the Transmitter and Receiver may
decrease the strength of the connection signal and reduce the overall
transmission range.
If a connection has been established and the HD Flow logo can be seen
on the display device, but content is not playing:
• Make sure that the input/output cables are properly connected.
• Verify that the Transmitter is set to the appropriate input port.
Warning Do not place the
PeerAirTM
Pro units near other devices that
emit excessive amounts of heat.
Increased temperatures may
cause the PeerAirTM Pro Transmitter
or Receiver unit to malfunction
or stop working.
Quick Start Guide for PeerAirTM Pro Wireless AV Multi-Display System - LIT-0906
Power/Source
Selection Button
© 2015 Peerless Industries, Inc. Peerless-AV™ is a trade mark of Peerle ss Industri es, Inc. All rig hts reser ved.
HD Flow™ is a trademark of I Do It, LTD. Other parties’ marks are the prop erty of thei r respectiv e owners. ww w.peerless -av.com
Quick Start Guide
Model No. HDS300 (-2, -3, -4, -5, -6)
POWER POWER
RECEIVERTRANSMITTER
ON OFF
MENU SCAN
/ BACK
INFO
/ OK
HDMI HDMI1
COMPONENT PC HDMI2
AV AV HDMI3
RECEIVER
HDMI
COMPONENT
AV
Powered byPowered b
y
Tip Repeat Steps
3-11 to connect more
than one Receiver unit
(HDS300-2, HDS300-3,
HDS300-4, HDS300-5,
HDS300-6)
POWER POWER
RECEIVERTRANSMITTER
ON OFF
MENU SCAN
/ BACK
INFO
/ OK
HDMI HDMI1
COMPONENTPC HDMI2
AV AV HDMI3
TRANSMITTER
HDMI1
PC HDMI2
AV HDMI3
4 of 11 2016-11-17 #180-9092-2 2016-12-06
NOTE: For mounting patterns smaller than VESA 400, use large enclosure mounting bracket (DD).
Loosely attach the enclosure mounting brackets (CC or DD) to the power module assembly (BB) with two
1/4-20 x 12 mm screws (II) and two 1/4-20 nuts (EE) as shown in fi g. 12.1. NOTE: The enclosure mounting
bracket can be installed with the inside notch facing downward if additional side-to-side adjustment is needed.
Attach the mounting brackets (CC or DD), open end of notch facing downward, to the adapter bracket with two
1/4-20 x 12 mm screws (II) and two 1/4-20 nuts (EE) as shown in fi g. 12.2.
Adjust the position of the power module assembly (BB) to your desired location as shown in fi g. 12.2. Once in
position, tighten the four 1/4-20 x 12 mm screws (II) using 4mm allen wrench (KK).
Wireless Receiver and Power Enclosure Installation
NOTE: For mounting patterns smaller than VESA 400, use large enclosure mounting bracket (DD).
NOTE: The Wireless Receiver Assembly (AA) and Power Module Assembly (BB) position can be interchanged
based on the display’s connector panel location. Install Wireless Receiver Assembly on the side closest to the
connector panel.
Loosely attach the enclosure mounting brackets (CC or DD) to the wireless receiver assembly (AA) with two
1/4-20 x 12 mm screws (II) and two 1/4-20 nuts (EE) as shown in fi g. 11.1. NOTE: The enclosure mounting
bracket can be installed with the inside notch facing downward if additional side-to-side adjustment is needed.
Attach the mounting brackets (CC or DD), open end of notch facing downward, to the adapter bracket with two
1/4-20 x 12 mm screws (II) and two 1/4-20 nuts (EE) as shown in fi g. 11.2.
Adjust the position of the receiver assembly (AA) to your desired location as shown in fi g. 11.2. Once in position,
tighten the four 1/4-20 x 12 mm screws (II) using 4mm allen wrench (KK).
1
fi g. 11.1 fi g. 11.2
EE
AA
II
INSIDE NOTCH
II
CC or
DD
AA
EE
INSIDE NOTCH
2
fi g. 12.1 fi g. 12.2
II
II
BB BB
EE
EE
INSIDE NOTCH
CC or
DD
5 of 11 2016-11-17 #180-9092-2 2016-12-06
NOTE: "X" dimensions should be equal.
NOTE: "Y" dimensions should be equal.
Installing Adapter Brackets to Universal Plate
To prevent scratching the screen, set a cloth on a fl at, level surface that will support the weight of the screen. Place
screen face side down. Refer to screen manufacturers instructions or customer service, for removing any knobs,
base, cover, or screw(s) on the back of the screen to prepare mounting. These need to be removed to allow the
adapter brackets to be attached.
Position adapter brackets over mounting holes on back of screen. Adjust the position of assemblies
(AA and BB) so that they are at least 32" apart. Make sure assemblies (AA and BB) are evenly spaced from the
adapter brackets. Tighten screws (II) to lock position of assemblies (AA and BB).
Select the small, medium, large or extra large screws from the baffl ed fastener pack then attach adapter brackets to
screen following fi gure 13.1.
NOTE: Top and bottom mounting holes must be used for attaching brackets. Verify that all holes are properly
aligned, and then tighten screws using a security allen wrench.
CENTER BRACKETS
VERTICALLY ON BACK
OF SCREEN
X
X
3
Notes:
• The number of fasteners used will vary,
depending upon the type of screen.
• Multi-washers and spacers may not be
used, depending upon the type of screen.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
MULTI-WASHER
• Tighten screws so adapter brackets are fi rmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
32" Min.
Y Y
BB AA
6 of 11 2016-11-17 #180-9092-2 2016-12-06
Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into
screen as shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place.
Do not over tighten. If screw cannot make three full turns into the screen, select a shorter length screw from the
baffl ed fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
3-1
If you have any questions, please call Peerless customer care at 1-800-865-2112.
SCREEN
MULTI-WASHER
SCREW
ADAPTER
BRACKET
fi g. 13.1
SPACER
7 of 11 2016-11-17 #180-9092-2 2016-12-06
Untie the wireless receiver power adapter cord and route as shown below. Plug the end of the power adapter into
the outlet marked DC on the wireless receiver as shown in detail 6. Coil up the excess cord and secure with a
cable tie (HH). Store the coiled cord between the power adapter and the power module wall as shown.
5
DC
LAN
USB
DETAIL 6
WIRELESS RECEIVER POWER
ADAPTER
DISPLAY NOT
SHOWN FOR
CLARITY
Wireless Receiver Assembly and Power Module Assembly Setup
Remove the two #8 screws securing the cover of the wireless receiver assembly (AA) as shown in detail 4. Open
the enclosure to expose the wireless receiver and IR Extender. Remove the M5 x 10mm phillips screws and open
the power module assembly (BB) as shown in detail 5.
4
DETAIL 4 DETAIL 5
#8 SCREW
M5 X 10mm SCREWS
AA
BB
8 of 11 2016-11-17 #180-9092-2 2016-12-06
Locate the IR Extender inside of the wireless receiver enclosure shown in fi gure 19.1. Remove the tie from the
cable and position the IR Extender on the display within line of sight of your remote as shown in fi gure 19.2.
Remove the adhesive backing from the IR Extender eye and attach to the display. Coil up the excess cord near
the wireless receiver enclosure (AA) and secure with a cable tie (HH). Store the coiled cord back inside of the
enclosure.
6
IR RECIEVER
IR RECIEVER fi g. 19.1
fi g. 19.2
Close the top cover of the wireless receiver assembly (AA), making sure that the power adapter cords run
underneath the cable opening as shown below. Re-install the two #8 screws.
7
CABLE OPENING
#8 SCREWS
9 of 11 2016-11-17 #180-9092-2 2016-12-06
Plug the power cord from your display into the triple
tap grounded outlet as shown. Coil up the excess
cord and secure with a cable tie (GG), inserting it
through the cable tie anchor (FF) and around the
coiled cord.
Close the top cover of the power module assembly
(BB), making sure that the power adapter cords run
underneath the cable opening as shown below.
Re-install the M5 x 10mm phillips screws.
Install the cable tie anchor (FF) onto the inside
back wall of the power enclosure (BB). Remove the
adhesive backing from the anchor and press into
place in the area shown.
Place the cords inside the cable management sheath
(JJ) by pushing the cables through the slit in the
sheath. NOTE: The sheath may need to be trimmed
to length before installing cords.
8 9
10 11
FF
JJ
CABLE
OPENING
M5 x 10mm SCREWS
Plug extension cord (not included) into power adapter.
13
EXTENSION CORD
GG
DISPLAY POWER
CORD
TRIPLE TAP
GROUNDED OUTLET
HDMI-OUT
Plug the component cable(s) from your display
(HDMI shown) into the wireless receiver.
12
COMPONENT
CABLE
10 of 11 2016-11-17 #180-9092-2 2016-12-06
Cord Management
Run extension cord (not included) through upright.
14
© 2014 Peerless Industries, Inc.
Peerless-AV® is a registered trademark of Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
To complete the installation of your wireless mount, please refer to the PeerAir Pro™ User's Manual and the
PeerAir Pro™ Install Guide included.
15
11 of 11 2016-11-17 #180-9092-2 2016-12-06
1 YEAR LIMITED WARRANTY
The HDS300 is distributed by Peerless Industries, Inc. using the highest quality components and technology available. The
Product is warranted to be free from defects in material and workmanship, given normal use and care, for 1 Year from the
original purchase date with proof of purchase. Please retain a copy of your receipt as you will need this to obtain warranty work.
We will repair or replace the product which fails as a result of such a defect during the warranty period. The accessories are not
covered by this warranty.
This warranty is the customers’ exclusive remedy for product defect and does not apply to:
• Any modifi cations made to the product in any way by the customer
• Attachments to the product by the customer that causes product damage
• Any product which the seals/and or serial numbers and/or logos have been broken, removed, or tampered with, defaced, or
altered in any manner
• Damage caused by abuse, misuse, accident, water, or theft
• Physical damage
• Loss of the Accessories
Except as stated above, Peerless Industries, Inc. makes no express or implied warranties as to
any product, in Particular, makes no warranty of merchantability or fi tness for any particular purpose. Peerless Industries, Inc.
shall not be liable for consequential or incidental damages arising from any product defect. Our liability is limited to replacement
of any defective product as stipulated under the warranty conditions. Peerless Industries, Inc. expressly disclaims all warranties
not satisfi ed in this limited warranty. Any implied warranties that may be imposed by law are limited to the terms of this limited
warranty.
WARRANTY
Customer Care
Need help with installation or set up? Call Peerless-AV Customer Care
1-800-865-2112 (available 7:00am- 7:00pm CST, Monday - Friday), or email us at info@peerless-av.com.
Peerless -AV
2300 White Oak Circle
Aurora, IL 60502 USA
www.peerless-av.com
CONTACT INFORMATION