Philips 1150X/40 User Manual
Displayed below is the user manual for 1150X/40 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
1190X
1180XCC
1180X
1160X
1160XCC
1150X
(Model 1180X Shown)
Rechargeable Cordless
Tripleheader Shaver
Always here to help you Question?
Contact
Philips
Norelco
Question?
Contact
Philips
Norelco
Register your product and get support at
www.norelco.com/register
2
ENGLISH 4
1190X/1180XCC/1180X/1160X/1160XCC/1150X
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register
WARNING
To reduce the risk of burns, fire, electric shock, or
injury to persons:
1. Close supervision is necessary when this shaver/
Jet Clean
System
/charging stand is used by, on, or near children or
invalids.
2. Use this shaver/
Jet Clean System
/charging stand for its
intended household use as described in this manual. Do not
use attachments or a cleaning solution not recommended by
Philips Electronics North America Corporation.
3. Never operate this shaver/
Jet Clean System
/charging stand if
it has a damaged cord or charging plug, if it is not working
properly, if it has been dropped or damaged, or dropped
into water while plugged in. For assistance call 1-800-243-
3050.
4. Keep the shaver,
Jet Clean System
, charging stand, cord and
charging plug away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not use the adapter in or near a power outlet that
contains an electric air freshener to prevent damage to the
adapter.
7. Do not clean, charge or plug in shaver/
Jet Clean System
outdoors or operate where aerosol (spray) products are
being used or where oxygen is being administered.
8. Do not use this shaver with a damaged or broken comb, as
facial injury may occur.
9. Always attach cord to Jet Clean System/charging stand first,
plug into outlet and then put shaver in Jet Clean System/
charging stand. Be certain plug is inserted firmly into
Jet
Clean System
/charging stand, up to mark indicated on plug.
To disconnect, turn
Jet Clean System
off. Then remove
charging plug from outlet.
10. Never put the shaver/
Jet Clean System
/charging stand in
direct sunlight or store at a temperature above 140°F.
11. Keep the
Jet Clean System, charging stand
and cord dry at all
times. Do not handle with wet hands.
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric appliance, basic precautions should
always be followed, including the following:
Read all instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a corded Jet Clean System/charging stand
that has fallen into water. Unplug immediately.
2. Power plug and the accessories connected to it are not for
immersion or for use in shower.
3. Do not use an extension cord with this appliance.
4. Do not place or store a Jet Clean System/charging stand
where it can fall or be pulled into a tub or sink. Do not
place or drop a Jet Clean System/charging stand into water
or other liquid.
5. Always unplug this Jet Clean System/charging stand from the
electrical outlet immediately after use, except when shaver
is (re)charging.
6. Unplug and remove power supply cord from Jet Clean
System/charging stand before cleaning.
7. The batteries used in this device may present a fire or
chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
ENGLISHENGLISH 54
7
Table of Contents
Features ...................................................... 8-11
Multi-Level Display ................................12-15
Charge Meter ...............................................15
Before First Use .....................................15-16
Charging ...................................................16-18
Recharging .....................................................19
Quick Charge ...............................................19
Put It To The Test & Shaving Tips ........19-20
How to Shave
With An Electric Shaver .......................20-22
Trimming ..................................................22-23
Travel Lock ..............................................23-24
Cleaning .................................................... 25-36
Replacing the Shaving Unit ..................36-37
Maintenance ..................................................38
Storage ......................................................38-39
Assistance ......................................................39
Disposal .......................................................... 40
Accessories ...................................................40
Warranty ........................................................41
ENGLISHENGLISH
6
45 - DAY MONEY-BACK GUARANTEE
To enjoy the closest and most comfortable shave from your new Philips Norelco
Men’s Shaver, the shaver should be used exclusively for 3 weeks. This allows your
hair and skin enough time to adapt to the Philips Norelco Shaving System. If, after
that period of time, you are not fully satisfied with your Philips Norelco Men’s
Shaver, send the product back along with dated sales receipt and we’ll refund
you the full purchase price. The shaver must be shipped prepaid by insured
mail, insurance prepaid, have the original sales receipt, indicating pur-
chase price, the date of purchase, and the money-back guarantee return
authorization form enclosed. We cannot be responsible for lost mail.
The shaver must be postmarked no later than 45 days from the date of purchase.
Philips Norelco reserves the right to verify the purchase price of the shaver and
limit refunds not to exceed suggested retail price.
To obtain money-back guarantee return authorization form,
call 1-800-243-3050 for assistance. Delivery of refund check will
occur 6–8 weeks AFTER receipt of refund product.
12. To prevent possible damage to the cord, do not wrap cord
around the shaver or
Jet Clean System
/charging stand.
13. Only use the power plug and other accessories supplied
with the shaver.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a transformer. Do
not cut off the power plug to replace it with another plug, as
this will cause a hazardous condition.
98 ENGLISH ENGLISH
How the Unique Philips Norelco Lift and Cut
Shaving System Makes Close Comfortable:
Groove channels
beard closer to
cutting system
Lifter raises hair Slots to cut long
hairs
Holes to cut short
hairs even closer
Click-On Precision
Trimmer
Automatic Worldwide
Voltage 100V to 240V AC
Cleaning Brush
Travel Pouch
(1190X/1180XCC/1180X/
1160X/1160XCC)
Charging Stand
Rechargeable 1-hour Full
Charge for up to 50 min.
(1190X/1180XCC/1180X/1160X/
1160XCC) or 40 min. (1150X)
of cordless shaving time
Quick Charge
Cordless - To shave
without a cord
Full 2-Year Warranty
45-Day Money-Back Guarantee
Model 1160X
Model 1160XCC
Model 1150X
Model 1190X
Model 1180X
Model 1180XCC
Features
GyroFlex 2D
Contour-Following System
Shaving Unit
• Hair Chamber
captures
shaven hair
SkinGlide System
Protective Cap
Electronic
On/Off Button
Replacement
Shaving Unit
Indicator
Travel Lock
Multi-Level
Display
• Shows remaining
power level in
batteries
(1180X/1180XCC)
• Battery Charge,
Full & Low
Indicators
10 ENGLISH 11
Features
Jet Clean System
(1180XCC/1160XCC)
Shaver Holder
Cleaning
Solution
Low
Indicator
Light
Cleaning
Indicator
Light
Drying
Indicator
Light
Cleaning
Solution
Canister
Release
Buttons
ON/OFF
Button
Removable Cleaning
Solution Canister
1312 ENGLISH
Multi-Level Display
◗ Remove any sticker or protective foil from
the display before using shaver.
◗ Depending on the shaver model, there are 3
different types of displays:
C Display for Models 1190X, 1180X and
1180XCC
C Display for Models 1160X and 1160XCC
C Display for Model 1150X
The display provides the following
information:
◗ Charging Indicator
CModels 1190X, 1180X, 1180XCC
-When the shaver is charging, the display goes on
and the bottom charging light blinks. As charging
continues, more and more lights will blink to
indicate what level the battery has been charged.
-Quick charge: When the shaver contains enough
energy for one shave, the bottom charging light
alternately blinks orange and white.
ENGLISH
CModels 1160X, 1160XCC and 1150X
-When the shaver is charging, the plug symbol
and battery symbol will blink alternately during
charging. After some time, the plug symbol goes
out and the battery symbol continues to blink
until the shaver is fully charged.
-Quick charge: When the shaver contains enough
energy for one shave, the plug symbol and battery
symbol stops blinking alternately and only the
battery symbol blinks.
NOTE: The displays of models 1160X, 1160XCC
and 1150X look different, but work the same way.
◗ Full Charge Indicator
CModels 1190X, 1180X, 1180XCC
-When the battery has been fully charged, all
charging lights light up continuously. After
approximately 30 minutes the display
automatically switches off again.
C Models 1060X, 1160XCC and 1150X
-When the battery has been fully charged,
the battery symbol lights up continuously.
After approximately 30 minutes the display
automatically switches off again.
NOTE: The displays of models 1160X, 1160XCC
and 1150X look different, but work the same way.
1514 ENGLISH
◗ Remaining Battery Capacity
C Models 1190X, 1180X, 1180XCC
-The remaining battery capacity is indicated by
the number of charging lights that are on.
◗ Low Battery Indicator
C Models 1190X, 1180X, 1180XCC
-When the battery is almost empty (5 or less
shaving minutes left), the bottom charging light
blinks orange. When you turn the shaver OFF the
bottom charging light continues to blink for a few
seconds.
C Models 1160X, 1160XCC and 1150X
-When the battery is almost empty (5 or less
shaving minutes left), the plug symbol blinks.
When you turn the shaver OFF the plug symbol
blinks for a few seconds.
NOTE: The displays of models 1160X, 1160XCC
and 1150X look different, but work the same way.
◗ Replacement Shaving Unit Indicator
C Every year, depending on your shaving behavior,
after turning the shaver OFF, the replacement
shaving unit symbol indicator starts to blink.
The replacement reminder is repeated at 9
successive shaves or until you reset the shaver.
This reminds you that with new shaving heads
you will guarantee yourself optimal shaving
performance.
ENGLISH
◗ Travel Lock
The shaver is equipped with a travel lock
function. You can use the travel lock function
when you are going to store the shaver for a
longer period or if you are going to take the
shaver with you when traveling. See ‘Travel
Lock’ section for instructions on how to use this
function.
Charge Meter
(1190X/1180X/1180XCC)
◗ Charge Meter monitors amount of remaining
battery power available. Remaining battery
capacity is based on the amount of power
consumed shaving per minute and is
dependent upon your skin and beard type,
whether you use pre-shave lotion, and how
often the trimmer is used.
◗ Initially your shaver may need to go through
2 or 3 full charge/recharge cycles before
remaining battery capacity indicators begin
to display your accurate battery power left.
Before First Use
◗ Charge the shaver before you start using
it (see ‘Charging’). Make sure the shaver is
switched off before you start charging it.
◗ Remove any sticker or protective foil from
the Display before using shaver.
1716 ENGLISH ENGLISH
Charging in the Charging Stand
C 1 Connect the small plug of cord to charging
stand.
C 2 Unfold the charging stand. You will hear a
‘click’.
3 Connect the power plug into any 100V to
240V AC outlet. Use only the power cord
provided.
◗ An adaptor plug may be necessary for power
cord usage in some foreign countries. Use
an attachment plug adaptor of the proper
configuration for the power outlet.
The power cord will automatically convert to
work on 100V to 240V AC systems.
C 4 Place shaver in stand in an upright position
(1). Press the shaver back into the holder
until it locks into place (2).
5 The display on the shaver will indicate
shaver is charging.
6 Charging requires one full hour. A fully
charged shaver has a cordless shaving
time of up to 50 minutes (models 1190X,
1180X, 1180XCC, 1160X and 1160XCC)
or 40 minutes (model 1150X).
Important
◗ Only use the power cord and charging stand
or Jet Clean System (models 1180XCC,
1160XCC) provided to charge the shaver.
◗ The power plug transforms 100-240V AC to
less than 24V DC.
Charging
◗ Charging, recharging or storing at
temperatures below 40°F (4°C) or higher
than 95°F (35°C) adversely affects lifetime of
batteries.
◗ Charging or recharging requires one full hour.
◗ A fully charged shaver has a shaving time of
up to 50 minutes (models 1190X, 1180X,
1180XCC, 1160X and 1160XCC) or 40
minutes (model 1150X).
◗ You may recharge when the bottom charging
light blinks orange (models 1190X, 1180X,
1180XCC) or the plug symbol blinks (models
1160X, 1160XCC and 1150X).
◗ Do not charge shaver in a pouch.
1
2
1918 ENGLISH
Charging Shaver with Jet Clean
System (1180XCC, 1160XCC)
1 Connect the small plug to the Jet Clean
System. Connect the charging plug into
any 100V to 240V AC outlet. Use only the
power cord provided.
The shaver holder automatically moves up to the
highest position.
C 2 Remove protective cap from shaver.
NOTE: The shaver cannot be placed in the Jet
Clean System when the trimmer or protective
cap is placed on the shaver.
C 3 Place the shaver head side down in the
shaver holder with the display facing the
front of the Jet Clean System.
C 4 Place the shaver into the holder behind
the two clips (1) and press the shaver
down to lock it into place (2).
5 The display on the shaver will indicate
shaver is charging.
6 Charging requires one full hour. A fully
charged shaver has a cordless shaving
time of up to 50 minutes (Models 1190X,
1180X, 1180XCC, 1160X and 1160XCC)
or 40 minutes (Model 1150X).
ENGLISH
Recharging
1 Recharging requires one full hour.
Recharge when the bottom charging light
blinks orange (models 1190X, 1180X,
1180XCC) or the plug symbol blinks
(models 1160X, 1160XCC and 1150X).
Quick Charge
When batteries are totally depleted, recharging
the shaver for approximately 3-5 minutes gives
enough energy for a 3-minute cordless shave.
Put It To The Test & Shaving Tips
◗ 21 Day Trial and Conversion Process. It is a fact
that your skin and beard need time to adjust to
a new shaving system.
◗ Use your new shaver exclusively for 3 weeks to
fully enjoy the closeness of a Philips Norelco
shave.
◗ At first you may not get as close a shave as you
expect, or your face may even become slightly
irritated. This is normal since your beard and
skin will need time to adjust. Invest 3 weeks
and you’ll soon experience the full joy of your
new shaver.
◗ Stick with it! If you alternate shaving methods
during the adjustment period, it may make it
more difficult to adapt to the Philips Norelco
shaving system.
1
2
ENGLISH
◗ If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
How To Shave With An Electric Shaver
C◗ This symbol on the shaver indicates that the
shaver can be used in the bath or shower.
◗ Make sure the charging stand/Jet Clean
System does not get wet or near water.
◗ Use this shaver for its intended household use
as described in this manual.
Shaving
C 1 Turn shaver ON by pressing the on/off
button once. Shave against the direction
of beard growth using only circular
movements.
The shaver display will light up briefly (Models
1190X, 1180X, 1180XCC).
2 Stretch your skin with your free hand so
blades can lift and cut whiskers. Gently
press shaver to skin so the floating heads
can follow the contours of your face.
DO NOT press too hard. Too much
pressure can pinch the skin into the combs.
20 ENGLISH
3 Turn shaver OFF by pressing the on/off
button once.
The display lights up for a few seconds and then
shows the remaining battery capacity (Models
1190X, 1180X. 1180XCC).
4 Clean the shaver after each use (see
chapter ‘Cleaning’).
C 5 Put the Protective Cap on the shaver to
protect shaver heads.
Wet Shaving
You can also use the shaver on a wet face with
shaving foam.
1 Apply some water to your skin.
2 Apply shaving foam to your skin.
3 Rinse the shaving unit under the tap
to ensure that the shaving unit glides
smoothly over your skin.
4 Press the on/off button once to switch on
the shaver.
5 Move the shaving heads in circular
movements over your skin.
NOTE: Rinse the shaver under the tap regularly
to ensure that it continues to glide smoothly over
your skin.
21
5 Trim beard, moustache or sideburns using
the trimmer.
6 Turn shaver OFF when finished.
The display lights up for a few seconds and then
shows the remaining battery capacity (Models
1190X, 1180X, 1180XCC).
7 Thoroughly clean the trimmer after using
(see ‘Cleaning’).
C 8 Pull the trimmer straight off the shaver.
NOTE: Do not turn the trimming unit while you
pull it off the shaver.
C 9 Insert the raised notch of the shaving unit
into the slot in the top of the shaver (1).
Press the shaving unit down to attach it to
the shaver (2). You will hear a ‘click’.
C 10 Put the Protective Cap on the shaver.
Travel Lock
If you are going to store the shaver for a longer
time period or if traveling, it is possible to lock the
shaver. The travel lock prevents the shaver from
being switched on by accident.
ENGLISH
6 Dry your face and thoroughly clean
the shaver after each use (see chapter
‘Cleaning’).
NOTE: Make sure you rinse all foam off the
shaver.
C 7 Put the Protective Cap on the shaver to
protect heads.
Trimming
To Groom Sideburns and Moustache:
C 1 Pull the shaving unit straight off the shaver.
NOTE: Do not turn the shaving unit while you
pull it off the shaver.
C 2 Insert the raised notch of the trimmer into
the slot in the top of the shaver (1). Press the
trimmer down to attach it to the shaver (2).
You will hear a ‘click’.
3 Turn shaver ON.
The display lights up for a few seconds (Models
1190X, 1180X, 1180XCC).
4 Hold trimmer to exact hairline desired.
Move trimmer downward with gentle
pressure.
22 ENGLISH 23
ENGLISH
Activating the travel lock
C 1 Press the ON/OFF button for 3 seconds.
C◗ The lock symbol lights up on the display.
NOTE: The displays of models 1190X, 1180X,
1180XCC, 1160X, 1160XCC and 1150X look
different, but show the same symbol.
2 The travel lock has now been activated.
Deactivating the travel lock
1 Press the ON/OFF button for 3 seconds.
2 The lock symbol goes out and the shaver
turns ON to indicate that the shaver has been
unlocked. The shaver is now ready for use.
BThe shaver unlocks automatically when charging in
the charging stand or Jet Clean System.
24 ENGLISH 25
3 sec.
Cleaning
◗ Always clean your shaver after each use.
◗ Regular cleaning guarantees better shaving
results.
◗ Never clean, remove or replace shaving unit
while motor is on.
◗ Do not apply pressure to shaving head combs.
Do not touch shaver heads with hard objects
as this may dent or damage precision-made
slotted combs.
◗ Do not use shaver if shaving head combs are
damaged or broken. Facial injury may occur.
◗ Do not use abrasives, scourers or aggressive
liquids such as gasoline or acetone to clean
the shaver or Jet Clean System.
Cleaning the Shaving Unit
The shaver heads may be quickly cleaned after
each use by rinsing with hot water. Water
from the tap should be on a hot setting, BUT
BE CAREFUL TO TEST WATER FIRST SO AS
NOT TO BURN OR SCALD HANDS.
◗ Regular cleaning guarantees better shaving
results.
◗ While rinsing shaver heads, water may drip
out of the base of shaver. This is a normal
occurrence.
1 Always turn shaver OFF, remove from
charging stand/Jet Clean System before
cleaning.
ENGLISH
C 2 For best results rinse the shaving unit by
running under hot water for a few minutes.
BE CAREFUL TO TEST WATER FIRST SO AS
NOT TO BURN OR SCALD HANDS.
C 3 Pull the shaving head holder off the
bottom part of the shaving unit and rinse
under hot water for 30 seconds.
4 Carefully shake off excess water and let
the shaving unit air dry.
NOTE: Do not wipe or dry the shaving unit
with a towel or tissue. This could damage the
shaving heads.
C 5 Push the shaving head holder back onto
the bottom of the shaving unit. You will
hear a ‘click’.
6 You may also clean the shaving unit and
hair chamber without water by using the
supplied brush.
Cleaning the Shaving Unit in the Jet
Clean System (1180XCC/1160XCC)
CAUTION: Keep cleaning solution out of
reach of children. Do not take internally. Avoid
contact with eyes. In case of eye contact,
thoroughly flush with cold water. If irritation
persists, get medical attention.
26 ENGLISH
Important
◗ Only use this shaver, charging stand,
Jet Clean
System
and HQ200 cleaning solution provided
to charge or clean shaver.
◗ Other Philips Norelco shavers DO NOT work
with this
Jet Clean System.
◗ Empty the cleaning solution canister and
thoroughly rinse the canister clean with warm
water every 2 weeks.
◗ The Jet Clean System thoroughly cleans but
does not disinfect your shaver, therefore, do
not share shaver with others.
◗ The charging plug converts 100-240V AC to
less than 24V DC.
◗ Place the
Jet Clean System
on a flat, stable and
fluid-resistant surface to avoid any leakage. Be
careful not to tip or move the
Jet Clean System
if it is filled with the cleaning solution.
◗ To avoid evaporation, do not expose cleaning
solution to direct sunlight.
◗ Remove the protective cap from the shaver
before charging or cleaning the shaver in the
Jet Clean System
.
◗ Use this appliance for its intended household
use as described in this manual.
1 Place the Jet Clean System on a flat, level
surface.
C 2 Simultaneously press the buttons located
on both sides of the Jet Clean System
(1) and lift the appliance off the Jet Clean
canister (2).
27
2
1
CF
ENGLISH
Always remove appliance from canister by lifting
straight up. Do not tilt Jet Clean System.
C 3 Pour the Jet Clean Solution (Model HQ200)
into the canister up to a level between the
two lines located inside the canister.
NOTE: ONLY USE PHILIPS NORELCO JET
CLEAN SOLUTION (MODEL HQ200) WITH
THE JET CLEAN SYSTEM. ANY OTHER
SOLUTION MAY CAUSE DAMAGE TO YOUR
Shaver.
C ◗ When the cleaning solution level drops below
the minimum level, the ‘cleaning chamber
empty’ symbol will blink and the shaver holder
will move to the starting position.
◗ If you clean your shaver every day, you should
clean and refill the canister approximately every
15 days.
C 4 Carefully lower the appliance back onto
the Jet Clean canister making sure the
release buttons snap back into place.
When the canister is filled with cleaning solution,
do not move appliance to prevent leakage.
28 ENGLISH
Jet Cleaning the Shaver
◗ If the shaver does not contain enough power
for one (1) shave, the Jet Clean Cleaning
System may not work properly. Charge the
shaver in the
Jet Clean System
before using
the Jet Clean System to clean your shaver.
◗ If you use the shaver with shaving foam,
quickly rinse under hot water before cleaning
in the Jet Clean System.
1 Connect the small plug to the
Jet Clean
System
. Connect the charging plug into
any 100V to 240V AC outlet. Use only the
charging plug provided.
2. Place the Jet Clean System on a flat, level
surface. Fill the canister with cleaning
solution (see ‘Preparing Jet Clean System
For Use’).
C 3 Remove protective cap from shaver.
C 4 Place the shaver head side down in the
shaver holder with the display facing the
front of the Jet Clean System.
29
will automatically move to the starting position.
The cleaning cycle can be re-started by
pressing the ON/OFF button once.
◗ If the power plug is disconnected before the
cleaning cycle is complete, the shaver holder will
remain in its current position. Reconnect the
plug into the outlet or
Jet Clean System
and the
shaver holder will automatically move to the
highest position. The cleaning cycle can be
re-started by pressing the ON/OFF button once.
C NOTE: If the cleaning solution level drops below
the minimum level during the cleaning cycle, the
‘cleaning chamber empty’ symbol will blink and
shaver holder returns the shaver to the starting
position, stopping the cleaning cycle. Unplug Jet
Clean System from the outlet, remove shaver
and refill canister (see “Preparing Jet Clean
System for Use”).
8 When the entire cleaning cycle is complete
and the shaver is hygienically clean, the
shaver will be raised to the starting position
and the display on the shaver will turn on
indicating that the shaver is (re)charging.
9 Pull the shaver forward and lift shaver from
Jet Clean System.
◗ If the shaver needs to be recharged, you can
simply leave it in the
Jet Clean System
after
cleaning and the shaver will automatically
recharge. The display on the shaver will
indicate the shaver is recharging.
ENGLISH
C 5 Place the shaver into the holder behind
the two clips (1) and press the shaver
down to lock into place (2).
The display on the shaver will indicate shaver is
charging.
C 6 Press the ON/OFF button on the Jet
Clean System to start the cleaning cycle.
The shaver display stops showing the charging
indication.
C 7 The cleaning light starts to blink and the
shaver is automatically lowered into the
cleaning solution.
The shaver stops charging while it is being
cleaned.
◗ During the first phase of the cleaning cycle,
the shaver will automatically turn on and off
several times while the shaver holder lowers
and raises the shaver’s position in the cleaning
solution, removing all debris. The cleaning
light will blink continuously throughout the
cleaning program.
C ◗ During the second phase of the cleaning cycle,
the shaver holder moves the shaver to the
drying position and the drying light will blink.
This phase will take approximately 2 hours.
The shaver will stay in one position until the
end of the drying program.
◗ Do not press the ON/OFF button while the
cleaning cycle is running. If this does occur, the
cleaning cycle will stop and the shaver holder
30 ENGLISH 31
1
2
ENGLISH
C 5 Remove the cutter from the comb.
Do not clean more than one cutter and comb
at a time, since they are all matching sets. If you
accidentally put a cutter in the wrong comb, it
may take several weeks before optimal shaving
performance is restored.
C 6 Clean the cutter with the cleaning brush
supplied.
C 7 Clean the inside of the comb.
C 8 After cleaning, place the cutter back into
the comb with the cutter legs pointing
downwards.
9 Repeat the process for the other two
cutters and combs.
C 10 Place the retaining frame back onto the
shaving head holder.
33
ENGLISH
◗ You may store your shaver in the
Jet Clean
System
.
Extra-thorough cleaning method
Do not mix up the cutters and combs as the
shaving performance may be adversely affected
for several weeks before optimal shaving
performance is restored.
1 Turn shaver OFF.
C 2 Pull the shaving head holder off the
bottom part of the shaving unit.
C 3 Slide the green retaining frame in the
direction of the arrows indicated on the
retaining frame.
C 4 Lift the retaining frame out of the shaving
head holder.
32
C 11 Slide the retaining frame back into place
(‘click’).
C 12 Reattach the shaving head holder to the
bottom part of the shaving unit.
Cleaning the Trimmer
Clean the trimmer after each use.
1 Turn shaver ON with trimmer attached to
shaver.
C 2 Rinse the trimmer under hot water. BUT
BE CAREFUL TO TEST WATER FIRST SO
AS NOT TO BURN OR SCALD HANDS.
3 Remove trimmer from shaver and allow to
air dry.
Tip: For optional trimmer performance, lubricate
the trimmer teeth with one drop of mineral oil
every 6 months.
34 ENGLISH 35
ENGLISH
Cleaning the Jet Clean Canister
(1180XCC/1160XCC)
For optimal performance of the Jet Clean
System, it is recommended that you empty the
cleaning solution canister and thoroughly rinse
the canister clean every 2 weeks.
1 Place the Jet Clean System on a flat, level
surface.
C 2 Simultaneously press the buttons located
on both sides of the Jet Clean System
(1) and lift the appliance off the Jet Clean
canister (2).
Always remove appliance from canister by lifting
straight up. Do not tilt Jet Clean System.
C 3 Discard any remaining cleaning solution in
the canister.
The cleaning solution can be safely poured down
the sink as there are no harmful ingredients.
C 4 Simply rinse the canister with warm water.
Wipe the canister with a towel or tissue
to remove excess water.
CF
2
1
ENGLISH
C 5 Pour the Jet Clean Solution into the
canister up to a level between the two
lines located inside the canister.
C 6 Carefully lower the Jet Clean System
over the canister making sure the release
buttons snap back into position.
Replacing the Shaving Unit
◗ Replace the shaving unit once a year for
optimal shaving results.
◗ Replace damaged or worn shaver heads with
model RQ11 Philips Norelco shaver heads
only.
◗ The individual shaving heads (cutters and
combs) are NOT replaceable. Only the one-
piece shaving unit can be replaced.
36 ENGLISH
Replacement Shaver Head Assembly
Indication
C ◗ After 12 months of use, the replacement head
indicator symbol starts to blink to remind you
to check if it’s time to replace your shaving
unit to obtain optimal shaving results.
Note: The displays of models 1160X, 1160XCC
and 1150X look different, but work the same way.
C 1 Pull the shaving head holder off the
bottom part of the shaving unit.
C 2 Attach the new shaving head holder to the
bottom part of the shaving unit (‘click’).
C 3 To reset the shaver, press and hold the On/
Off button for approximately 10 seconds.
Note: If you do not reset the shaver at the first
replacement reminder, it continues to show the
shaving unit symbol at 8 more shaves or until you
reset the shaver.
This shaver/charging stand/Jet Clean System has
no other user-serviceable parts. For assistance
call 1-800-243-3050.
37
RQ11
3 sec.10 sec.
◗ Do not place or store charging stand/Jet
Clean System where it can fall or be pulled
into a tub or sink, water or other liquid while
plugged in.
C ◗ If storing shaver in the charging stand, put the
Protective Cap on shaver to protect heads.
Assistance
◗ For assistance, visit our website:
www.philips.com/support or
call toll free 1-800-243-3050
◗ Online information is available 24 hours a day,
7 days a week.
ENGLISH 39
ENGLISH
Maintenance
◗ Always remove shaver from the charging
stand/Jet Clean System before cleaning
appliance.
◗ The charging stand/Jet Clean System and
shaver
may be wiped clean using a damp cloth.
◗ Water from the tap should be on a warm
setting to clean any washable parts.
Note: DO NOT place or clean any parts of the
charging stand/Jet Clean System in a dishwasher.
Storage
◗ The shaver can be placed in the charging
stand/Jet Clean System for safe storage.
◗ If appliance will not be used for an extended
period of time, it is recommended that the
cleaning solution in the Jet Clean canister be
emptied out before storing.
◗ Be sure shaver is turned off. Remove cord
from outlet and charging stand or Jet Clean
System before storing in a safe, dry location
where it will not be crushed, banged, or
subject to damage.
◗ Do not wrap power cord around shaver/
charging stand or Jet Clean System when
storing.
◗ Store cord in a safe location where it will not
be cut or damaged.
38
ENGLISH
Disposal
C ◗ This Philips Norelco shaver contains a
rechargeable Lithium-Ion battery
which must be disposed of properly.
◗ Contact your local town or city officials
for battery disposal information or call
1-800-8-BATTERY or www.rbrc.com for
battery drop-off locations.
◗ For assistance, visit our website,
www.philips.com/support or call toll free:
1-800-243-3050.
Accessories
C ◗ Replacement Shaving Unit
Model RQ11 - For maximum shaver
performance, replace your Philips Norelco
shaver heads once a year.
◗ Click-on Beard Styler
Model RQ111 - Philips Norelco Click-on
Beard Styler
◗ Cleaning Solution
HQ200 - Philips Norelco Jet Clean Solution,
10 fl. oz. /300 ml.
◗ Philips Norelco Shaver Accessories may be
purchased at a store near you, or on our
website www.philips.com/store
40 ENGLISH 41
FULL TWO YEAR WARRANTY
Philips Electronics North America Corporation warrants each new Philips Norelco Product,
Models 1190X/1180X/1180XCC/1160X/1160XCC/1150X (except cutters and combs) against
defects in materials or workmanship for a period of two years from the date of purchase, and
agrees to repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse,
lack of reasonable care, the affixing of any attachment not provided with the product or loss of
parts or subjecting the product to any but the specified voltage.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/norelco or call
1-800-243-3050 for assistance. It is suggested that for your protection you return shipments of
product by insured mail, insurance prepaid. Damage occurring during shipment is not covered
by this warranty.
NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America
Corporation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages, so the above exclusion and limitations may not apply to you.
* Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Division of Philips Electronics North America Corporation
P.O.Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco, Tripleheader, Lift and Cut, and are Registered Trademarks of Philips Electronics
North America Corporation.
is a Trademark of Philips Electronics North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips N.V.
© 2015 Philips Electronics North America Corporation. All Rights Reserved.