Philips 1250X/45 User Manual
Displayed below is the user manual for 1250X/45 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
1290X
1280X
1280XCC
1260X
1250X
1250XCC
Rechargeable Cordless
Tripleheader Razor
Register your product and get support at
www.philips.com/norelco
(Model 1290X Shown)
2
ENGLISH 4
1290X/1280X/1280XCC/1260X/1250X/1250XCC
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.philips.com/norelco
water while plugged in. For assistance call 1-800-243-3050.
4. Keep the razor,
Jet Clean System
, charging stand, cord and
charging plug away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not clean, charge or plug in razor/
Jet Clean System
outdoors or operate where aerosol (spray) products are being
used or where oxygen is being administered.
7. Do not use this razor with a damaged or broken comb, as
facial injury may occur.
8. Always put razor in Jet Clean System/charging stand first,
attach cord to Jet Clean System/charging stand, then plug
into outlet. Be certain plug is inserted firmly into
Jet Clean
System
/charging stand, up to mark indicated on plug. To
disconnect, turn
Jet Clean System
/charging stand off then
remove charging plug from outlet.
9. Never put the razor/
Jet Clean System
/charging stand in direct
sunlight or store at a temperature above 140°F.
10. Keep the
Jet Clean System, charging stand
and cord dry at all
times. Do not handle with wet hands. Do not store in a damp
environment.
11. To prevent possible damage to the cord, do not wrap cord
around the razor or
Jet Clean System
/charging stand.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a transformer. Do not
cut off the power plug to replace it with another plug, as this will
cause a hazardous condition.
• Only use power plug supplied with the razor.
• Only use Jet Clean System supplied with the razor.
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric appliance, basic precautions should always
be followed, including the following:
Read all instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a corded Jet Clean System/charging stand that
has fallen into water. Unplug immediately.
2. Charging stand is not for immersion or for use in shower.
3. Do not use an extension cord with this appliance.
4. Do not place or store a Jet Clean System/charging stand where
it can fall or be pulled into a tub or sink. Do not place or drop
a Jet Clean System/charging stand into water or other liquid.
5. Always unplug this Jet Clean System/charging stand from the
electrical outlet immediately after use, except when razor is
(re)charging.
6. Unplug and remove power supply cord from Jet Clean System/
charging stand before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury
to persons:
1. Close supervision is necessary when this razor/
Jet Clean System
/
charging stand is used by, on, or near children or invalids.
2. Use this razor/
Jet Clean System
/charging stand for its intended
household use as described in this manual. Do not use
attachments or a cleaning solution not recommended by Philips
Electronics North America Corporation.
3. Never operate this razor/
Jet Clean System
/charging stand if
it has a damaged cord or charging plug, if it is not working
properly, if it has been dropped or damaged, or dropped into
ENGLISHENGLISH 54
7
Table of Contents
Features ...................................................... 8-11
Multi-Level Display ................................12-16
Charge Meter ...............................................16
Before First Use .....................................16-17
Charging ...................................................17-20
Recharging .....................................................20
Quick Charge ...............................................20
Put It To The Test & Shaving Tips ..............21
How to Shave
With An Electric Razor ........................21-23
Trimming ..................................................23-24
Travel Lock ..............................................24-25
Cleaning ....................................................25-37
Replacing the Shaving Unit ........................38
Maintenance ............................................38-39
Storage ............................................................39
Assistance ...................................................... 40
Battery Removal ....................................40-41
Accessories ...................................................41
Warranty ........................................................ 43
ENGLISHENGLISH
6
45 - DAY MONEY-BACK GUARANTEE
To enjoy the closest and most comfortable shave from your new Philips Norelco
Men’s Razor, the razor should be used exclusively for 3 weeks. This allows your
hair and skin enough time to adapt to the Philips Norelco Shaving System. If, after
that period of time, you are not fully satisfied with your Philips Norelco Men’s
Razor, send the product back along with dated sales receipt and we’ll refund you
the full purchase price. The razor must be shipped prepaid by insured mail,
insurance prepaid, and have the original sales receipt, indicating pur-
chase price and the date of purchase, enclosed. We cannot be respon-
sible for lost mail. The razor must be postmarked no later than 45 days from
the date of purchase. Philips Norelco reserves the right to verify the purchase
price of the razor and limit refunds not to exceed suggested retail price.
To obtain money-back guarantee return authorization form, call 1-800-243-3050
for assistance. Please allow 4-6 weeks for delivery of check.
8 9
Precision Trimmer
Automatic Worldwide
Voltage 100V to 240V AC
Cleaning Brush
Storage Pouch
Charging Stand
Rechargeable 1-hour Full
Charge for up to 60 min.
(1290X/1280X/1280XCC/
1260X) or 50 min.
(1250X/1250XCC)
Quick Charge
Cordless - To shave without
a cord
Full 2-Year Warranty
45-Day Money-Back
Guarantee
ENGLISH ENGLISH
Smooth: UltraTrack heads catch every hair
with just a few strokes
3 specialized shaving tracks:
Slots for normal hairs
Channels for long hairs
Holes for short stubbles
Model 1260X
Model 1250X
Model 1250XCC
Model 1290X
Model 1280X
Model 1280XCC
1
2
3
Features
GyroFlex 3D Contour-Following System
Shaving Unit
• Hair Chamber
captures shaven
hair
SkinGlide System
Protective Razor
Head Cap
Electronic
On/Off Button
Multi-Level Display
• Shows remaining
power level in
batteries (1260X/
1250X/1250XCC) or
actual remaining
shaving minutes
(1290X/1280X/1280XCC)
• Battery Charge,
Full & Low Indicators
Cleaning Indicator
Blocked Shaving Heads
Indicator
Replacement Shaving
Unit Indicator
Travel Lock
10 ENGLISH 11
Features
Jet Clean System
(1280XCC/1250XCC)
Razor Holder
Cleaning
Indicator Light
Drying
Indicator Light
ON/OFF
Button
Cleaning
Program
Selector
Button
(1280XCC)
Cleaning
Solution
Canister
Release
Buttons
Cleaning
Solution Low
Indicator Light
Removable Cleaning
Solution Canister
12 13
ENGLISH
Multi-Level Display
◗ Remove any sticker or protective foil from
the display before using razor.
◗ Depending on the razor model, there are 3
different types of displays:
C Display for Models 1290X, 1280X and
1280XCC
C Display for Model 1260X
C Display for Models 1250X and 1250XCC
The display provides the following
information:
◗ Charging Indicator
C Models 1290X, 1280X and 1280XCC
-As soon as you connect the power cord to
an electrical outlet, the display goes on and the
minutes indication will start blinking. The display
shows an increase in shaving minutes from
0 to 60.
ENGLISH
-Quick charge: When the razor contains enough
energy for one shave, the display shows 5 minutes
in white.
C Models 1260X, 1250X and 1250XCC
-As soon as you connect the power cord to
an electrical outlet, the bottom charging light
blinks, then the second charging light, and so on.
-Quick charge: When the razor contains enough
energy for one shave, the bottom charging light
blinks white.
NOTE: The displays of models 1260X, 1250X and
1250XCC look different, but work the same way.
◗ Full Charge Indicator
C Models 1290X, 1280X and 1280XCC
-When the battery has been fully charged,
the minutes indication lights up continuously.
After approximately 30 minutes the display
automatically switches off again.
C Models 1260X, 1250X and 1250XCC
-When the battery has been fully charged,
all charging lights light up continuously.
After approximately 30 minutes the display
automatically switches off again.
NOTE: The displays of models 1260X, 1250X and
1250XCC look different, but work the same way.
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
14 15
ENGLISH
◗ Remaining Battery Capacity
C Models 1290X, 1280X and 1280XCC
-The remaining battery capacity is indicated by
the number of shaving minutes shown on the
display.
C Models 1260X, 1250X and 1250XCC
-The remaining battery capacity is indicated by
the blinking charging lights.
◗ Low Battery Indicator
C Models 1290X, 1280X and 1280XCC
-When the battery is almost empty (5 or less
shaving minutes left), the minutes indication
blinks. When you turn the razor OFF the minutes
indication continues to blink for a few seconds. You
will hear a beep when there are no minutes left.
C Models 1260X, 1250X and 1250XCC
-When the battery is almost empty (5 or less
shaving minutes left), the bottom charging light
blinks orange. When you turn the razor OFF the
bottom charging light continues to blink orange
for a few seconds.
NOTE: The displays of models 1260X, 1250X and
1250XCC look different, but work the same way.
C ◗ Replacement Shaving Unit Indicator
Every year, depending on your shaving behavior,
after turning the razor OFF, the replacement
ENGLISH
shaving unit symbol indicator starts to blink. For
models 1290X, 1280X and 1280XCC, you will
also hear a beep. The replacement shaving unit
symbol will remain visible for the next 7 shaves to
remind you that with new shaving heads you will
guarantee yourself optimal shaving performance.
C ◗ Blocked Shaving Heads Indicator
If the display shows a blinking replacement
shaving unit symbol and faucet symbol with
exclamation mark, clean the razor thoroughly
before continuing to shave (see ‘Cleaning’).
After cleaning, if the blinking replacement shaving
unit symbol and faucet symbol with exclamation
mark remain on the display, immediately replace
the shaving unit (see ‘Replacing the Shaving Unit’).
C ◗ Cleaning Indicator
For optimal shaving performance, we
recommend cleaning the razor after EACH use.
The blinking faucet symbol will remind you the
shaving unit needs to be cleaned. This happens
after each shave.
NOTE: The displays of models 1290X, 1280X,
1280XCC, 1260X, 1250X and 1250XCC look
different, but work the same way.
◗ Power-saving mode (1290X only)
The razor is equipped with an automatic power-
saving mode. When the razor enters the power-
saving mode, the light in the on/off button goes
out to save energy.
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
MINUTES LEFT
16 17
ENGLISH
-This will occur when the appliance is moved for
5 minutes without switching it on. The razor will
automatically go into power-saving mode.
C ◗ The lock symbol blinks on the display to
indicate the appliance is in power-saving mode.
-To deactivate the power-saving mode, simply
press the on/off button.
Charge Meter
◗ Charge Meter monitors amount of remaining
battery power (Models 1260X, 1250X and
1250XCC) and actual shaving ‘minutes left’
(Models 1290X, 1280X and 1280XCC).
‘Minutes left’ or remaining battery capacity
is based on the amount of power consumed
shaving per minute and is dependent upon
your skin and beard type, whether you use
pre-shave lotion, and how often the trimmer
is used.
◗ Initially your razor may need to go through 2
or 3 full charge/recharge cycles before
‘minutes left’ (Models 1290X, 1280X and
1280XCC) or remaining battery capacity
indicators (Models 1260X, 1250X and
1250XCC) begins to display your accurate
shaving minutes or battery power left.
Before First Use
◗ Charge the razor before you start using it
(see ‘Charging’). Make sure the razor is
ENGLISH
switched off before you start charging it.
◗ Remove any sticker or protective foil from
the Display before using razor.
Important
◗ Only use the power cord and charging stand
or Jet Clean System (models 1280XCC and
1250XCC only) provided to charge the razor.
◗ The power plug transforms 100-240V AC to
less than 24V DC.
Travel Lock (1280X, 1280XCC, 1260X,
1250X and 1250XCC)
The razor is equipped with a travel lock function.
You can use the travel lock function when you are
going to store the razor for a longer period or if
you are going to take the razor with you when
traveling. See ‘Travel Lock’ section for instructions
on how to use this function.
Charging
◗ Charging, recharging or storing at
temperatures below 40ºF or higher than 95ºF
adversely affects lifetime of batteries.
◗ Always unplug this charging stand/Jet Clean
System from the electrical outlet immediately
after use, except when razor is (re)charging.
You can store the razor in the charging stand
or Jet Clean System.
MINUTES LEFT
MINUTES LEFT
18 19
ENGLISH
◗ Charging or recharging requires one full hour.
◗ A fully charged razor has a shaving time of
up to 60 minutes (models 1290X, 1280X,
1280XCC and 1260X) or 50 minutes (models
1250X and 1250XCC).
◗ You may recharge when the minutes
indication blinks (models 1290X, 1280X and
1280XCC) or the bottom charging light
blinks orange (models 1260X, 1250X and
1250XCC).
◗ Do not charge razor in a pouch.
Charging in the Charging Stand
C 1 Connect the small plug of cord to charging
stand. Connect the power plug into any
100V to 240V AC outlet. Use only the
power cord provided.
◗ An adaptor plug may be necessary for power
cord usage in some foreign countries. Use
an attachment plug adaptor of the proper
configuration for the power outlet.
The power cord will automatically convert to
work on 100V to 240V AC systems.
C 2 Place razor in stand in an upright position
Press the razor tightly into the holder
making sure the charging contacts on each
side of the razor fit into the holder.
ENGLISH
3 The display on the razor will indicate razor
is charging.
4 Charging requires one full hour. A fully
charged razor has a cordless shaving
time of up to 60 minutes (models 1290X,
1280X, 1280XCC and 1260X) or 50
minutes (models 1250X and 1250XCC).
Charging Razor with Jet Clean
System (1280XCC and 1250XCC)
1 Connect the small plug to the Jet Clean
System. Connect the charging plug into
any 100V to 240V AC outlet. Use only the
charging plug provided.
The razor holder automatically moves up to the
highest position.
C 2 Remove protective razor head cap from
razor.
NOTE: The razor cannot be placed in the Jet
Clean System when the protective razor head cap
is placed on the razor.
C 3 Place the razor head side down in the
razor holder with the display facing the
front of the Jet Clean System.
NOTE: The minutes indication (model 1280XCC)
and charging lights (model 1250XCC) on the
display will turn upside down so you can see what
level the battery is charged.
ENGLISH
C 4 Press the razor tightly into the holder to
lock it into place.
5 The display on the razor will indicate razor
is charging.
6 Charging requires one full hour. A fully
charged razor has a cordless shaving
time of up to 60 minutes (models 1290X,
1280X, 1280XCC and 1260X) or 50
minutes (models 1250X and 1250XCC).
Recharging
1 Recharging requires one full hour.
Recharge when the minutes indication
blinks (models 1290X, 1280X and
1280XCC) or the bottom charging light
blinks orange (models 1260X, 1250X and
1250XCC).
Always unplug charging stand/Jet Clean System
from the electrical outlet immediately after use,
except when razor is (re)charging.
Quick Charge
When batteries are totally depleted, recharging
the razor for approximately 3-5 minutes gives
enough energy for a 3-minute cordless shave.
20 ENGLISH
Put It To The Test & Shaving Tips
◗ 21 Day Trial and Conversion Process. It is a fact
that your skin and beard need time to adjust to
a new shaving system.
◗ Use your new razor exclusively for 3 weeks to
fully enjoy the closeness of a Philips Norelco
shave.
◗ At first you may not get as close a shave as you
expect, or your face may even become slightly
irritated. This is normal since your beard and
skin will need time to adjust. Invest 3 weeks
and you’ll soon experience the full joy of your
new razor.
◗ Stick with it! If you alternate shaving methods
during the adjustment period, it may make it
more difficult to adapt to the Philips Norelco
shaving system.
◗ If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
How To Shave With An Electric Razor
C◗ This symbol on the razor indicates that the
razor can be used in the bath or shower.
◗ Make sure the charging stand/Jet Clean
System does not get wet or near water.
◗ Shaving with a clean face gives the best results.
◗ Use this razor for its intended household use
as described in this manual.
21
ENGLISH
Shaving
C 1 Turn razor ON by pressing the on/off
button once. Shave against the direction
of beard growth using both straight and
circular movements.
The razor display will light up briefly.
2 Stretch your skin with your free hand so
blades can lift and cut whiskers. Gently
press razor to skin so the floating heads
can follow the contours of your face.
DO NOT press too hard. Too much
pressure can pinch the skin into the combs.
3 Turn razor OFF by pressing the on/off
button once.
The display lights up for a few seconds and then
shows the remaining battery capacity.
4 Clean the razor after each use (see
chapter ‘Cleaning’).
C 5 Put the Protective Razor Head Cap on the
razor to protect razor heads.
Wet Shaving
You can also use the razor on a wet face with
shaving foam.
1 Apply some water to your skin.
22 ENGLISH
2 Apply shaving foam to your skin.
3 Rinse the shaving unit under the tap
to ensure that the shaving unit glides
smoothly over your skin.
4 Press the on/off button once to switch on
the razor.
5 Move the shaving heads in circular
movements over your skin.
NOTE: Rinse the razor under the tap regularly to
ensure that it continues to glide smoothly over
your skin.
6 Dry your face and thoroughly clean
the razor after each use (see chapter
‘Cleaning’).
NOTE: Make sure you rinse all foam off the razor.
C 7 Put the Protective Razor Head Cap on the
razor to protect heads.
Trimming
To Groom Sideburns and Moustache:
1 Turn razor ON.
The display lights up for a few seconds.
C 2 Press the trimmer slide forward to slide out
the trimmer.
23
ENGLISH
3 Hold trimmer to exact hairline desired.
Move trimmer downward with gentle
pressure.
4 Trim beard, moustache or sideburns using
the trimmer.
5 Turn razor OFF when finished.
The display lights up for a few seconds and then
shows the remaining battery capacity.
6 Thoroughly clean the trimmer after using
(see ‘Cleaning’).
7 Press the trimmer slide backwards to
retract the trimmer.
C 8 Put the Protective Razor Head Cap on the
razor.
Travel Lock (1280X, 1280XCC,
1260X, 1250X and 1250XCC)
If you are going to store the razor for a longer
time period or if traveling, it is possible to lock
the razor. The travel lock prevents the razor from
being switched on by accident.
24 ENGLISH
Activating the travel lock
C 1 Press the ON/OFF button for 3 seconds.
◗ Models 1280X and 1280XCC, the display
starts to count down from 3. At 1, the razor
beeps to indicate it is locked.
◗ Model 1250XCC, the top charging light blinks,
then the second charging light and so on.
◗ The lock symbol appears on the display.
NOTE: The displays of models 1280X, 1280XCC,
1260X, 1250X and 1250XCC look different, but
show the same symbol.
2 The travel lock has now been activated.
Deactivating the travel lock
1 Press the ON/OFF button for 3 seconds.
2 The lock symbol goes out and the razor
turns ON to indicate that the razor has been
unlocked. The razor is now ready for use.
BThe razor unlocks automatically when charging in
the charging stand or Jet Clean System.
Cleaning
◗ Always clean your razor after each use.
◗ Regular cleaning guarantees better shaving
results.
25
3 sec
ENGLISH
◗ Never clean, remove or replace shaving unit
while motor is on.
◗ Do not apply pressure to shaving head combs.
Do not touch razor heads with hard objects
as this may dent or damage precision-made
slotted combs.
◗ Do not use razor if shaving head combs are
damaged or broken. Facial injury may occur.
◗ Do not use abrasives, scourers or aggresive
liquids such as gasoline or acetone to clean
the razor or Jet Clean System.
Cleaning the Shaving Unit
The razor heads may be quickly cleaned after
each use by rinsing with hot water. Water from
the tap should be on a hot setting, BUT BE
CAREFUL TO TEST WATER FIRST SO AS NOT
TO BURN OR SCALD HANDS.
◗ Regular cleaning guarantees better shaving
results.
◗ While rinsing razor heads, water may drip
out of the base of razor. This is a normal
occurrence.
1 Always turn razor OFF, remove from
charging stand/Jet Clean System before
cleaning.
C 2 Rinse the shaving unit by running under
hot water for a few minutes.
26 ENGLISH
C 3 Using your thumb and forefinger, grasp the
sides of the shaving head near the center
of the shaving unit and pull each individual
shaving head open.
C 4 Rinse all three shaving heads and three
hair chambers under hot tap water by
letting the water run in and around all the
openings for at least 30 seconds.
BE CAREFUL TO TEST WATER FIRST SO AS
NOT TO BURN OR SCALD HANDS.
5 You can also brush the shaving heads and
hair chambers with the brush supplied.
6 Carefully shake off excess water and leave
the shaving heads open to dry the shaving
unit completely.
NOTE: Do not wipe or dry the shaving unit with
a towel or tissue. This could damage the shaving
heads.
C 7 Press each shaving head back onto the
shaving unit. You will hear a ‘click’.
27
CF
CF
ENGLISH
Cleaning the Shaving Unit in the
Jet Clean System (1280XCC and
1250XCC)
CAUTION: Keep cleaning solution out of
reach of children. Do not take internally. Avoid
contact with eyes. In case of eye contact,
thoroughly flush with cold water. If irritation
persists, get medical attention.
Important
◗ Only use this razor, charging stand,
Jet Clean
System
and HQ200 cleaning solution provided
to charge or clean razor.
◗ Other Philips Norelco razors DO NOT work
with this
Jet Clean System.
◗ Empty the cleaning solution canister and
thoroughly rinse the canister clean with warm
water every 2 weeks.
◗ The Jet Clean System thoroughly cleans but
does not disinfect your razor, therefore, do not
share razor with others.
◗ The charging plug converts 100-240V AC to
less than 24V DC.
◗ Place the
Jet Clean System
on a flat, stable and
fluid-resistant surface to avoid any leakage. Be
careful not to tip or move the
Jet Clean System
if it is filled with the cleaning solution.
◗ To avoid evaporation, do not expose cleaning
solution to direct sunlight.
◗ Remove the protective razor head cap from
the razor before charging or cleaning the
razor in the
Jet Clean System
.
28 ENGLISH
◗ Use this appliance for its intended household
use as described in this manual.
1 Place the Jet Clean System on a flat, level
surface.
C 2 Simultaneously press the buttons located
on both sides of the Jet Clean System
(1) and lift the appliance off the Jet Clean
canister (2).
Always remove appliance from canister by lifting
straight up. Do not tilt Jet Clean System.
3 Unscrew the lid on the Jet Clean Solution
bottle (Model HQ200) provided with the
razor. Remove the airtight seal by lifting up
the tabs on the seal.
C 4 Pour the Jet Clean Solution into the canister
up to a level between the two lines located
inside the canister.
NOTE: ONLY USE PHILIPS NORELCO JET
CLEAN SOLUTION (MODEL HQ200) WITH
THE JET CLEAN SYSTEM. ANY OTHER
SOLUTION MAY CAUSE DAMAGE TO YOUR
RAZOR.
C ◗ When the cleaning solution level drops below
the minimum level, the ‘cleaning chamber
empty’ symbol will blink and the razor holder
will move to the starting position.
29
ENGLISH
◗ If you clean your razor every day, you should
clean and refill the canister approximately every
15 days.
C 5 Carefully lower the appliance back onto
the Jet Clean canister making sure the
release buttons snap back into place.
When the canister is filled with cleaning solution,
do not move appliance to prevent leakage.
Jet Cleaning the Razor
◗ If the razor does not contain enough power
for one (1) shave, the Jet Clean Cleaning
System may not work properly. Charge the
razor in the
Jet Clean System
before using the
Jet Clean System to clean your razor.
◗ If you use the razor with shaving foam, quickly
rinse under hot water before cleaning in the
Jet Clean System.
1 Connect the small plug to the
Jet Clean
System
. Connect the charging plug into
any 100V to 240V AC outlet. Use only the
charging plug provided.
2. Place the Jet Clean System on a flat, level
surface. Fill the canister with cleaning
solution (see ‘Preparing Jet Clean System
For Use’).
30 ENGLISH
C 3 Remove protective razor head cap from
razor.
C 4 Place the razor head side down in the
razor holder with the display facing the
front of the Jet Clean System.
C 5 Press the razor tightly into the holder of
the Jet Clean System to lock into cleaning
cycle position.
The display on the razor will indicate razor is
charging.
6 Model 1280XCC only, press the up/down
button to select a cleaning program.
You can choose from 3 cleaning programs: eco
program, auto program and intensive program.
NOTE: The eco program has a shorter drying time
and the intensive program is a more thorough
cleaning program.
7 Press the ON/OFF button to start the
cleaning cycle.
Model 1250XCC only, the system begins the
automatic cleaning program.
31
ENGLISH
razor holder will automatically move to the
highest position. The cleaning cycle can be
re-started by pressing the ON/OFF button
once.
C NOTE: If the cleaning solution level drops below
the minimum level during the cleaning cycle, the
‘cleaning chamber empty’ symbol will blink and
razor holder returns the razor to the starting
position, stopping the cleaning cycle. Unplug Jet
Clean System from the outlet, remove razor and
refill canister (see “Preparing Jet Clean System
for Use”).
8 When the entire cleaning cycle is complete
and the razor is hygienically clean, the
razor will be raised to the starting position
and the display on the razor will turn on
indicating that the razor is (re)charging.
C 9 Pull the razor forward and lift razor from
Jet Clean System.
◗ If the razor needs to be recharged, you can
simply leave it in the
Jet Clean System
after
cleaning and the razor will automatically
recharge. The display on the razor will indicate
the razor is recharging.
◗ You may store your razor in the
Jet Clean
System
. Unplug from the outlet when
charging/cleaning is complete.
33
ENGLISH
C 8 The cleaning light starts to blink and the
razor is automatically lowered into the
cleaning solution.
The razor stops charging while it is being cleaned.
◗ The cleaning cycle takes 4 to 6 minutes. For
model 1280XCC only, the intensive program
takes approximately 35 minutes.
◗ During the first phase of the cleaning cycle,
the razor will automatically turn on and off
several times while the razor holder lowers
and raises the razor’s position in the cleaning
solution, removing all debris. The cleaning
light will blink continuously throughout the
cleaning program.
C ◗ During the second phase of the cleaning cycle,
the razor holder moves the razor to the
drying position and the drying light will blink.
This phase will take approximately 2 hours.
Model 1280XCC only, the drying phase takes
1 hour when the eco program is selected.
The razor will stay in one position until the
end of the drying program.
◗ Do not press the ON/OFF button while the
cleaning cycle is running. If this does occur, the
cleaning cycle will stop and the razor holder
will automatically move to the starting
position. The cleaning cycle can be re-started
by pressing the ON/OFF button once.
◗ If the power plug is disconnected before the
cleaning cycle is complete, the razor holder will
remain in its current position. Reconnect the
plug into the outlet or
Jet Clean System
and the
32
Extra-thorough cleaning method
Do not mix up the cutters and combs as the
shaving performance may be adversely affected
for several weeks before optimal shaving
performance is restored.
1 Turn razor OFF.
C 2 Pull the shaving unit straight off the razor.
Do not turn the shaving unit when you pull it off
the razor.
C 3 Using your thumb and forefinger, grasp the
sides of the shaving head near the center
of the shaving unit and pull each individual
shaving head open.
C 4 Press the retainer release tab (1) until the
retainer opens (2).
C 5 Remove the cutter from the comb.
Do not clean more than one cutter and comb
at a time, since they are all matching sets. If you
accidentally put a cutter in the wrong comb, it
may take several weeks before optimal shaving
performance is restored.
34 ENGLISH 35
ENGLISH
1
2
C 6 Clean the cutter with the cleaning brush
supplied.
C 7 Clean the inside of the comb.
C 8 After cleaning, place the cutter back into
the comb with the cutter legs pointing
downwards.
9 Repeat the process for the other two
cutters and combs.
C 10 Press down the retainer over the cutter.
C 11 Close the shaving heads.
ENGLISH
C 12 Insert the notch of the shaving unit into
the slot in the top of the razor (1). Then
press the shaving unit down (2) to attach it
to the razor. You will hear a ‘click’.
Cleaning the Trimmer
Clean the trimmer after each use.
1 Press the trimmer slide forward to slide
out the trimmer.
C 2 Rinse the trimmer under hot water. BUT
BE CAREFUL TO TEST WATER FIRST SO
AS NOT TO BURN OR SCALD HANDS.
3 Allow trimmer to air dry.
Tip: For optional trimmer performance, lubricate
the trimmer teeth with one drop of mineral oil
every 6 months.
Cleaning the Jet Clean Canister
(1280XCC and 1250XCC)
For optimal performance of the Jet Clean
System, it is recommended that you empty the
cleaning solution canister and thoroughly rinse
the canister clean every 2 weeks.
1 Place the Jet Clean System on a flat, level
surface.
36 ENGLISH
C 2 Simultaneously press the buttons located
on both sides of the Jet Clean System
(1) and lift the appliance off the Jet Clean
canister (2).
Always remove appliance from canister by lifting
straight up. Do not tilt Jet Clean System.
C 3 Discard any remaining cleaning solution in
the canister.
The cleaning solution can be safely poured down
the sink as there are no harmful ingredients.
C 4 Simply rinse the canister with warm water.
Wipe the canister with a towel or tissue
to remove excess water.
C 5 Pour the Jet Clean Solution into the
canister up to a level between the two
lines located inside the canister.
C 6 Carefully lower the Jet Clean System
over the canister making sure the release
buttons snap back into position.
37
CF
2
1
ENGLISH 39
ENGLISH
Replacing the Shaving Unit
◗ Replace the shaving unit once a year for
optimal shaving results.
◗ Replace damaged or worn razor heads with
model RQ12 Philips Norelco razor heads only.
◗ The individual shaving heads (cutters and
combs) are NOT replaceable. Only the
one-piece shaving unit can be replaced.
Replacement Razor Head Assembly
Indication
C ◗ The replacement head indicator symbol starts
to blink and you will hear a beep (models
1290X, 1280X and 1280XCC) to remind you
to check if it's time to replace your shaving
unit to obtain optimal shaving results.
This razor/charging stand/Jet Clean System has no
other user-serviceable parts. For assistance call
1-800-243-3050.
Maintenance
◗ Always remove razor from the charging stand/
Jet Clean System before cleaning appliance.
◗ Unplug the charging stand/Jet Clean System
after charging/recharging or cleaning razor.
The charging stand/Jet Clean System and razor
may be wiped clean using a damp cloth.
38
◗ Water from the tap should be on a warm
setting to clean any washable parts.
Note: DO NOT place or clean any parts of the
charging stand/Jet Clean System in a dishwasher.
Storage
◗ The razor can be placed in the charging stand/
Jet Clean System for safe storage. Remove the
plug from outlet as soon as the razor is fully
charged or cleaned.
◗ If appliance will not be used for an extended
period of time, it is recommended that the
cleaning solution in the Jet Clean canister be
emptied out before storing.
◗ Be sure razor is turned off. Remove cord from
outlet and charging stand or Jet Clean System
before storing in a safe, dry location where
it will not be crushed, banged, or subject to
damage.
◗ Do not wrap cord around razor/charging
stand or Jet Clean System when storing.
◗ Store cord in a safe location where it will not
be cut or damaged.
◗ Do not keep charging stand or Jet Clean
System permanently plugged into outlet.
◗ Do not place or store charging stand/Jet
Clean System where it can fall or be pulled
into a tub or sink, water or other liquid while
plugged in.
C ◗ If storing razor in the charging stand, put
the Protective Razor Head Cap on razor to
protect heads.
MINUTES LEFT
MINUTES LEFT
ENGLISH
Assistance
◗ For assistance, visit our website: www.philips.
com/support or call 1-800-243-3050.
◗ Information is available 24 hours a day,
7 days a week.
Battery Removal
C ◗ This Philips Norelco razor contains a
rechargeable Lithium-Ion battery
which must be disposed of properly.
◗ Battery should only be removed when
razor is to be discarded.
◗ For assistance, visit our website,
www.philips.com/support or call toll free:
1-800-243-3050.
1 Turn razor ON.
2 Allow razor to run until the battery is
empty/depleted.
3 Turn razor OFF.
4 Use a screwdriver to remove the back
panel of the razor.
5 Remove the rechargeable battery.
6 Do not attempt to replace battery.
Insulate battery ends by covering with tape
and/or place battery in a small plastic bag.
40 ENGLISH 41
7 Discard your razor. Do not attempt to
plug electrical cord into the outlet or
recharge the razor after the battery has
been removed.
8 Contact your local town or city officials
for battery disposal information or call
1-800-8-BATTERY or www.rbrc.com for
battery drop-off locations.
Accessories
◗ Replacement Shaving Unit
Model RQ12 - For maximum razor
performance, replace your Philips Norelco
razor heads once a year.
◗ Shaving Head Cleaning Spray
HQ110 - Philips Norelco Shaving Head
Cleaning Spray
◗ Cleaning Solution
HQ200 - Philips Norelco Jet Clean Solution,
10 fl. oz. /300 ml.
◗ Philips Norelco Razor Accessories may be
purchased at a store near you, or on our
website www.philips.com/store
42 ENGLISH 43
FULL TWO YEAR WARRANTY
Philips Electronics North America Corporation warrants each new Philips Norelco Product,
Models 1290X/1280X/1280XCC/1260X/1250X/1250XCC (except cutters and combs) against
defects in materials or workmanship for a period of two years from the date of purchase, and
agrees to repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse,
lack of reasonable care, the affixing of any attachment not provided with the product or loss
of parts or subjecting the product to any but the specified voltage.* Use of unauthorized
replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION WILL NOT PAY
FOR WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED REPAIR
SERVICE AND WILL NOT REIMBURSE THE CONSUMER FOR DAMAGE RE-
SULTING FROM WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
REPAIR SERVICE. NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/norelco or call
1-800-243-3050 for assistance. It is suggested that for your protection you return shipments of
product by insured mail, insurance prepaid. Damage occurring during shipment is not covered
by this warranty.
NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America
Corporation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages, so the above exclusion and limitations may not apply to you.
* Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Division of Philips Electronics North America Corporation
P.O.Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco, Tripleheader, Lift and Cut, and are Registered Trademarks of Philips Electronics
North America Co rporation.
is a Trademark of Philips Electronics North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips Electronics N.V.
© 2010 Philips Electronics North America Corporation. All Rights Reserved.