Table of Contents
Philips 190S1CB/00 User Manual
Displayed below is the user manual for 190S1CB/00 by Philips which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
Safety and Troubleshooting Information
• Safety Precautions and Maintenance
• FAQs
• Troubleshooting
• Regulatory Information
Safety and Troubleshooting Information
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than
those specified in this documentation may result in exposure to shock,
electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and using your computer monitor:
Operation:
● Keep the monitor out of direct sunlight and away from stoves or any other heat source.
● Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics.
● Do not block the ventilation holes on the cabinet.
● When positioning the monitor, make sure the power plug and outlet are easily accessible.
● If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching
the power cable or DC power cord for normal operation.
● Please use approved power cord provided by Philips all the time. If your power cord is missing, please
contact with your local service center. (Please refer to Customer Care Consumer Information Center)
● Do not subject the LCD monitor to severe vibration or high impact conditions during operation.
● Do not knock or drop the monitor during operation or transportation.
Maintenance:
● To protect your display from possible damage, do not put excessive pressure on the LCD panel. When
moving your monitor, grasp the frame to lift; do not lift the monitor by placing your hand or fingers on the LCD
panel.
● Unplug the monitor if you are not going to use it for an extensive period of time.
● Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry
cloth when the power is off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids
to clean your monitor.
● To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or
excessive moisture environment.
● If your monitor gets wet, wipe it with dry cloth as soon as possible.
● If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the
power cord. Then, remove the foreign substance or water, and send it to the maintenance center.
● Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or extreme cold.
● In order to maintain the best performance of your monitor and use it for a longer lifetime, please use the
monitor in a location that falls within the following temperature and humidity ranges.
❍ Temperature: 0-40°C 32-95°F
❍ Humidity: 20-80% RH
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/safety.htm（第 1／2 页）2009-8-13 14:54:19
Safety and Troubleshooting Information
● IMPORTANT: Always activate a moving screen saver program when you leave your monitor unattended.
Always activate a periodic screen refresh application if your LCD monitor will display unchanging static
content. Uninterrupted display of still or static images over an extended period may cause “burn in”, also
known as “after-imaging” or “ghost imaging”, on your screen. "Burn-in", "after-imaging", or "ghost imaging" is
a well-known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or
“ghost imaging” will disappear gradually over a period of time after the power has been switched off.
WARNING: Severe” burn-in” or “after-image” or “ghost image” symptoms will not disappear
and cannot be repaired. The damage mentioned above is not covered under your
warranty.
Service:
● The casing cover should be opened only by qualified service personnel.
● If there is any need for any document for repair or integration, please contact with your local service center.
(please refer to the chapter of "Consumer Information Center")
● For transportation information, please refer to "Physical Specifications".
● Do not leave your monitor in a car/trunk under direct sun light.
Consult a service technician if the monitor does not operate normally, or you are not sure what
procedure to take when the operating instructions given in this manual have been followed.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/safety.htm（第 2／2 页）2009-8-13 14:54:19
FAQs (Frequently Asked Questions)
• Safety and Troubleshooting
• General FAQs
• Compatibility with Other Peripherals
• LCD Panel Technology
• Ergonomics, Ecology and Safety
Standards
• Troubleshooting
• Regulatory Information
FAQs (Frequently Asked Questions)
General FAQs
Q1: When I install my monitor what should I do if the screen shows 'Cannot display this
video mode'?
A: Recommended resolution for Philips 19": 1440x900 @60Hz.
1. Unplug all cables, then connect your PC to the monitor that you used previously.
2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel Window, select
the Display icon. Inside the Display Control Panel, select the 'Settings' tab. Under the setting
tab, in box labeled 'desktop area', move the slidebar to 1440x900 pixels (19").
3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.
4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at 1440x900@60Hz
(19").
5. Shut down your computer, disconnect your old monitor and reconnect your Philips LCD monitor.
6. Turn on your monitor and then turn on your PC.
Q2: What does the recommended refresh rate for LCD monitor?
A:Recommended refresh rate in LCD monitors is 60Hz, In case of any disturbance on screen, you can
set it up to 75Hz to see if that removes the disturbance.
Q3: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .
icm)?
A: These are the driver files for your monitor. Follow the instructions in your user manual to install the
drivers. Your computer may ask you for monitor drivers (.inf and .icm files) or a driver disk when you first
install your monitor. Follow the instructions to insert the ( companion CD-ROM) included in this package.
Monitor drivers (.inf and .icm files) will be installed automatically.
Q4: How do I adjust the resolution?
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/saf_faq.htm（第 1／4 页）2009-8-13 14:54:21
FAQs (Frequently Asked Questions)
A: Your video card/graphic driver and monitor together determine the available resolutions. You can
select the desired resolution under Windows® Control Panel with the "Display properties".
Q5: What if I get lost when I am making monitor adjustments?
A: Simply press the OK button, then select 'Reset' to recall all of the original factory settings.
Q6: Will the LCD screen be resistant to scratches?
A: In general it is recommended that the panel surface is not subjected to excessive shocks and is
protected from sharp or blunt objects. When handling the monitor, make sure that there is no pressure or
force applied to the panel surface side. This may affect your warranty conditions.
Q7: How should I clean the LCD surface?
A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol. Do
not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc.
Q8:Can I change the color setting of my monitor?
A:Yes, you can change your color setting through OSD control as the following procedures,
1. Press "OK" to show the OSD (On Screen Display) menu
2. Press "Down Arrow" to select the option "Color" then press "OK" to enter color setting, there are three
settings as below.
a. Color Temperature; The six settings are 5000K, 6500K, 7500K, 8200K, 9300K and
11500K. With settings in the 5000K range the panel appears ‘warm,' with a red-white color
tone, while a 11500K temperature yields ‘cool, blue-white toning."
b. sRGB; this is a standard setting for ensuring correct exchange of colors between different
device (e.g. digital cameras, monitors, printers, scanners, etc)
c. User Define; the user can choose his/her preference color setting by adjusting red, green
blue color.
*A measurement of the color of light radiated by an object while it is being heated. This measurement is
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/saf_faq.htm（第 2／4 页）2009-8-13 14:54:21
FAQs (Frequently Asked Questions)
expressed in terms of absolute scale, (degrees Kelvin). Lower Kevin temperatures such as 2004K are
red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K.
Q9: Can the Philips LCD Monitor be mounted on the wall?
A: Yes. Philips LCD monitors have this optional feature. For standard VESA mount holes on the rear
cover allows the user to mount the Philips monitor on most of the VESA standard arms or accessories.
We recommend to contact your Philips sales representative for more information.
RETURN TO TOP OF THE PAGE
Compatibility with other Peripherals
Q10: Can I connect my LCD monitor to any PC, workstation or Mac?
A: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and workstations. You
may need a cable adapter to connect the monitor to your Mac system. Please contact your Philips sales
representative for more information.
Q11: Are Philips LCD monitors Plug-and-Play?
A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000, XP, Vista and Linux.
RETURN TO TOP OF THE PAGE
LCD Panel Technology
Q12: What kind of wide-angle technology is available?
A: Currently, the IPS type panels offer the best Contrast Ratio, compared to MVA, or PVA
technologies. TN panels have improved over the years, but still cannot match the Contrast Ratio offered
by IPS panel.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/saf_faq.htm（第 3／4 页）2009-8-13 14:54:21
FAQs (Frequently Asked Questions)
RETURN TO TOP OF THE PAGE
Ergonomics, Ecology and Safety Standards
Q13: What is Image Sticking, or Image Burn-in, or After Image, or Ghost Image in LCD
panels?
A: Uninterrupted display of still or static images over an extended period may cause "burn in", also
known as "after-imaging" or "ghost imaging", on your screen. "Burn-in", "after-imaging", or "ghost
imaging" is a well-known phenomenon in LCD panel technology. In most cases, the "burned in" or "atter-
imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been
switched off.
Always activate a moving screen saver program when you leave your monitor unattended.
Always activate a periodic screen refresh application if your LCD monitor will display unchanging static
content.
WARNING: Severe"burn-in" or "after-image" or "ghost image" symptoms will not disappear and
cannot be repaired. The damage mentioned above is not covered under your warranty.
Q14: Why is my Display not showing sharp text, and is displaying jagged characters?
A: Your LCD monitor works best at its native resolution of 1440x900@60Hz. For best display please
use this resolution.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/saf_faq.htm（第 4／4 页）2009-8-13 14:54:21
Troubleshooting
• Safety and
Troubleshooting
• FAQs
• Common Problems
• Imaging Problems
• Regulatory Information
Troubleshooting
This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips
customer service representative.
Common Problems
Having this problem Check these items
No Picture
(Power LED not lit)
● Make sure the power cord is plugged into the power outlet and into the back
of the monitor.
● First, ensure that the power button on the front of the monitor is in the OFF
position, then press it to the ON position.
No Picture
(Power LED is white blinking)
● Make sure the computer is turned on.
● Make sure the signal cable is properly connected to your computer.
● make sure the monitor cable has no bent pins on the connect side. If yes,
repair or replace the cable.
● The Energy Saving feature may be activated
Screen says
● Make sure the monitor cable is properly connected to your computer. (Also
refer to the Quick Set-Up Guide).
● Check to see if the monitor cable has bent pins.
● Make sure the computer is turned on.
AUTO button doesn't function in VGA mode
● The auto function is applicable only in VGA-Analog mode. If the result is
not satisfactory, you can do manual adjustments via the OSD menu. Note
that the Auto Function is not applicable in DVI-Digital mode as it is not
necessary.
Imaging Problems
Image is not centered
● Press the Auto button.
● Adjust the image position using the Phase/Clock of Setup in OSD Main
Controls.
Image vibrates on the screen
● Check that the signal cable is properly securely connected to the graphics
board or PC.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/saf_troub.htm（第 1／3 页）2009-8-13 14:54:25
Troubleshooting
Vertical flicker appears
● Press the Auto button.
● Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main
Controls.
Horizontal flicker appears
● Press the Auto button.
● Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main
Controls.
image appears blurred, indistinct or too dark ● Adjust the contrast and brightness on On-Screen Display.
An "after-image", "burn-in" or "ghost image"
remains after the power has been turned off.
● Uninterrupted display of still or static images over an extended period may
cause " burn in", also known as "after-imaging " or "ghost imaging", on your
screen. "Burn-in", "after-imaging", or "ghost imaging" is a well-known
phenomenon in LCD panel technology. In most cases, the "burned in" or
"after-imaging" or "ghost imaging" will disappear gradually over a period of
time after the power has been switched off.
● Always activate a moving screen saver program when you leave your
monitor unattended.
● Always activate a periodic screen refresh application if your LCD monitor
will display unchanging static content.
Image appears distorted. Text is fuzzy or blurred.
● Set the PC’s display resolution to the same mode as monitor’s
recommended screen native resolution.
Green, red, blue, dark, and white dots appears on
the screen
● The remaining dots are normal characteristic of the liquid crystal used in
today’s technology, Pls refer the pixel policy for more detail.
The "power on" light is too strong to disturb me.
● You can adjust “power on” light using the power LED of Setup in OSD main
Controls.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/saf_troub.htm（第 2／3 页）2009-8-13 14:54:25
Troubleshooting
For further assistance, refer to the Consumer Information Centers list and contact Philips customer service representative.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/saf_troub.htm（第 3／3 页）2009-8-13 14:54:25
Regulatory Information
• TCO'03 Information
•Recycling Information for Customers
•Waste Electrical and Electronic Equipment-
WEEE
•CE Declaration of Conformity
•Energy Star Declaration
• Federal Communications Commission
(FCC) Notice (U.S. Only)
•FCC Declaration of Conformity
c Commission Federale de la Communication
(FCC Declaration)
• EN 55022 Compliance (Czech Republic
Only)
• Polish Center for Testing and Certification
Notice
•North Europe (Nordic Countries) Information
• BSMI Notice (Taiwan Only)
• Ergonomie Hinweis (nur Deutschland)
• Philips End-of-Life Disposal
•China RoHS
• Lead-free guarantee
• Troubleshooting
•Frequently Asked Questions (FAQs)
Regulatory Information
*available for selective models
TCO'03 Information
Congratulations!
The display you have just purchased carries the TCO'03 Displays label. This means that your display
is designed, manufactured and tested according to some of the strictest quality and environmental
requirements in the world. This makes for a high performance product, designed with the user in focus
that also minimizes the impact on our natural environment.
Some of the features of the TCO'03 Display requirements.
Ergonomics
● Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and
strain problems. Important parameters are luminance, contrast, resoluction, reflectance, colour rendition and image stability.
Energy
● Energy-saving mode after a certain time-beneficial both for the user and the environment
● Electrical safety
Emissions
● Electromagnetic fields
● Noise emissions
Ecology
● The product must be prepared for recycling and the manufacturer must have a certified environmental management system
such as EMAS or ISO 14 000
● Restrictions on
❍ chlorinated and brominated flame retardants and polymers
❍ heavy metals such as cadmium, mercury and lead.
For more information, please visit
www.tcodevelopment.com
RETURN TO TOP OF THE PAGE
Recycling Information for Customers
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 1／10 页）2009-8-13 14:54:31
Regulatory Information
There is currently a system of recycling up and running in the European countries, such as The Netherlands, Belgium, Norway, Sweden
and Denmark.
In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA) to follow the IT product
recycling management process, detail can be found in web site www.epa.gov.tw
The monitor contains parts that could cause damage to the nature environment. Therefore, it is vital that the monitor is recycled at the end of its
life cycle.
For help and service, please contact Consumers Information Center or F1rst Choice Contact Information Center in each country.
RETURN TO TOP OF THE PAGE
Waste Electrical and Electronic Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EC governing used
electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal
of this equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off
such waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household
or the store at which you purchased the product.
Attention users in United States:
Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal laws. For the
disposal or recyciing information, contact www.mygreenelectronics.com or www.eiae.org.
RETURN TO TOP OF THE PAGE
EPEAT
“The EPEAT (Electronic Product Environmental Assessment Tool) program evaluates computer desktops, laptops, and monitors based
on 51 environmental criteria developed through an extensive stakeholder consensus process supported by US EPA.
EPEAT system helps purchasers in the public and private sectors evaluate, compare and select desktop computers, notebooks and
monitors based on their environmental attributes. EPEAT also provides a clear and consistent set of performance criteria for the design
of products, and provides an opportunity for manufacturers to secure market recognition for efforts to reduce the environmental impact
of its products.”
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 2／10 页）2009-8-13 14:54:31
Regulatory Information
Benefits of EPEAT
Reduce use of primary materials
Reduce use of toxic materials
Avoid the disposal of hazardous waste
EPEAT’S requirement that all registered products meet ENERGY STAR’s energy efficiency specifications, means that these products
will consume less energy throughout their life.
RETURN TO TOP OF THE PAGE
ROHS is a European Directive aiming to control the use of certain hazardous substances in the production of new electrical and
electronic equipment. Philips has completely eliminated four of six RoHS-banned substances form its products by 1998-eight full years
before compliance was required and has lowered usage of the remaining substances significantly below the mandated levels.
RETURN TO TOP OF THE PAGE
CE Declaration of Conformity
This product is in conformity with the following standards
- EN60950-1:2001 (Safety requirement of Information Technology Equipment)
- EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment)
- EN55024:1998 (Immunity requirement of Information Technology Equipment)
- EN61000-3-2:2006 (Limits for Harmonic Current Emission)
- EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable
- 2006/95/EC (Low Voltage Directive)
- 2004/108/EC (EMC Directive)
and is produced by a manufacturing organization on ISO9000 level.
The product also comply with the following standards
- ISO13406-2 (Ergonomic requirement for Flat Panel Display)
- GS EK1-2000 (GS specification)
- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)
- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)
- TCO'03, TCO Displays 5.0 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and Emission, TCO: Swedish
Confederation of Professional Employees) for TCO versions.
RETURN TO TOP OF THE PAGE
Energy Star Declaration
This monitor is equipped with a function for saving energy which supports the VESA DPM standard. This means that
the monitor must be connected to a computer which supports VESA DPM. Time settings are adjusted from the
system unit by software.
VESA State LED Indicator Power Consumption
Normal operation ON (Active) White < 16.6 W (typ.)
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 3／10 页）2009-8-13 14:54:31
Regulatory Information
Power Saving
Alternative 2
One step Sleep White (blinking) < 0.8 W (typ.)
Switch Off Off < 0.5 W (typ.)
As an ENERGY STAR® Partner, we have determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
We recommend you switch off the monitor when it is not in use for a long time.
RETURN TO TOP OF THE PAGE
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS.
RETURN TO TOP OF THE PAGE
FCC Declaration of Conformity
Declaration of Conformity for Products Marked with FCC Logo,
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 4／10 页）2009-8-13 14:54:31
Regulatory Information
United States Only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
RETURN TO TOP OF THE PAGE
Commission Federale de la Communication (FCC Declaration)
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de
l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une protection raisonnable contre
les interférences nuisibles dans le cadre d'une installation résidentielle. CET appareil produit, utilise et peut
émettre des hyperfréquences qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent
causer des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir l'absence
d'interférences dans le cadre d'une installation particulière. Si cet appareil est la cause d'interférences nuisibles
pour la réception des signaux de radio ou de télévision, ce qui peut être décelé en fermant l'équipement, puis
en le remettant en fonction, l'utilisateur pourrait essayer de corriger la situation en prenant les mesures
suivantes:
● Réorienter ou déplacer l'antenne de réception.
● Augmenter la distance entre l'équipement et le récepteur.
● Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.
● Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de conformité est
susceptible d'interdire à l'utilisateur l'usage du présent équipement.
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE MATERIEL
BROUILLEUR DU CANADA.
RETURN TO TOP OF THE PAGE
EN 55022 Compliance (Czech Republic Only)
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 5／10 页）2009-8-13 14:54:31
Regulatory Information
RETURN TO TOP OF THE PAGE
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works
together (computer, monitor, printer, and so on) should have the same power supply source.
The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form of a fuse with
a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be
located near the equipment and easily accessible.
A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107
and PN-89/E-06251.
RETURN TO TOP OF THE PAGE
North Europe (Nordic Countries) Information
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 6／10 页）2009-8-13 14:54:31
Regulatory Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN
UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT
TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA
PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL
ER LETTE Å NÅ.
RETURN TO TOP OF THE PAGE
BSMI Notice (Taiwan Only)
RETURN TO TOP OF THE PAGE
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen"
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 7／10 页）2009-8-13 14:54:31
Regulatory Information
festgelegten Vorschriften.
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da die
Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind.
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß
1. Reparaturen nur durch Fachpersonal durchgeführt werden.
2. nur original-Ersatzteile verwendet werden.
3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu
verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem Zeichenkontrast wären die Folge).
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß NETZSTECKER UND
NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
RETURN TO TOP OF THE PAGE
End-of-Life Disposal
Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the
amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old monitor from your sales representative.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations.
For additional information on recycling contact www.eia.org (Consumer Education Initiative)
RETURN TO TOP OF THE PAGE
China RoHS
The People's Republic of China released a regulation called "Management Methods for Controlling Pollution by Electronic Information
Products" or commonly referred to as China RoHS. All products including CRT and LCD monitor which are produced and sold for China
market have to meet China RoHS request.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 8／10 页）2009-8-13 14:54:31
Regulatory Information
环保使用期限
此标识指期限(十年),电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外泄或突
变, 电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身、 财产造成严重损害的期
限．
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 9／10 页）2009-8-13 14:54:31
Regulatory Information
RETURN TO TOP OF THE PAGE
Lead-free guarantee
Lead free display promotes environmentally sound recovery and disposal of waste from electrical and electronic
equipment. Toxic substances like Lead has been eliminated and compliance with European community’s stringent
RoHs directive mandating restrictions on hazardous substances in electrical and electronic equipment have been
adhered to in order to make Philips monitors safe to use throughout its life cycle.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/safety/regs/regulat.htm（第 10／10 页）2009-8-13 14:54:31
About This Manual
• About This Guide
• Notational Descriptions
About This Manual
About This Guide
This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's
features, setup, operation and other important information. Its contents are identical to the information in our printed
version.
It includes the following sections:
● Safety and Troubleshooting Information provides tips and solutions for common problems as well as other
related information you may need.
● About This Electronic User's Manual gives an overview of information included, along with notation icon
descriptions and other documentation for your reference.
● Product Information gives an overview of the monitor's features as well as the technical specifications for this
monitor.
● Installing Your Monitor describes the initial setup process and gives an overview of how to use the monitor.
● On-Screen Display provides information on adjusting the settings on your monitor.
● Customer Care and Warranty contains a list of worldwide Philips Consumer Information Centers along with
help desk phone numbers and information on the warranty applicable to your product.
● Download and Print Option transfers this entire manual to your hard drive for easy reference.
RETURN TO TOP OF THE PAGE
Notational Descriptions
The following subsections describe notational conventions used in this document.
Notes, Cautions and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks
contain notes, cautions or warnings. They are used as follows:
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/about/about.htm（第 1／2 页）2009-8-13 14:54:34
About This Manual
NOTE: This icon indicates important information and tips that help you make
better use of your computer system.
CAUTION: This icon indicates information that tells you how to avoid either
potential damage to hardware or loss of data.
WARNING: This icon indicates the potential for bodily harm and tells you how
to avoid the problem.
Some warnings may appear in alternate formats and may not be accompanied by an icon. In such cases, the specific
presentation of the warning is mandated by the relevant regulatory authority.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/about/about.htm（第 2／2 页）2009-8-13 14:54:34
Product Information
• Your LCD Monitor
• Smartimage
• SmartContrast
• SmartSaturate
• SmartSharpness
• Technical Specifications
• Resolution & Preset Modes
• Philips Pixel Defect Policy
• Automatic Power Saving
• Product Views
• Physical Function
• SmartControl II
Product Information
Your LCD monitor
Congratulations on your purchase and welcome to Philips. To fully benefit from the support that Philips offers, register your product at. www.
philips.com/welcome
SmartImage
What is it?
SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness
in real time. Whether you're working with text applications, displaying images or watching a video, Philips SmartImage delivers great optimized
LCD display performance.
Why do I need it?
You want a LCD display that delivers optimized display all your favorite types of content, SmartImage software dynamically adjust brightness,
contrast, color and sharpness in real time to enhance your LCD viewing experience.
How does it work?
SmartImage is an exclusive, leading edge Philips technology that analyzes the content displayed on your screen. Based on a scenario you
select, SmartImage dynamically enhances the contrast, color saturation and sharpness of images and videos for ultimate display performance -
all in real time with the press on a single button.
How to enable SmartImage?
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 1／11 页）2009-8-13 14:54:38
Product Information
1. Press to launch the SmartImage on screen display;
2. Keep press to toggle between Office Work, Image Viewing, Entertainment, Economy, and Off;
3. The SmartImage on screen display will remain on screen for 5 seconds or you can also press”OK” to make confirmation.
4. When SmartImage is enabled, the sRGB scheme is disabled automatically. To use sRGB you need to disable SmartImage with the
button at the front bezel of your monitor.
Except using key to scroll down, you can also press buttons to choose and press “OK” to confirm selection and close the
SmartImage OSD.There are five modes to be selected: Office Work, Image Viewing, Entertainment, Economy, and Off.
There are five modes to be selected: Office Work, Image Viewing, Entertainment, Economy, and Off.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 2／11 页）2009-8-13 14:54:38
Product Information
1. Office Work: Enhances text and dampens brightness to increase readability and reduce eye strain. This mode significantly enhances
readability and productivity when you’re working with spreadsheets, PDF files, scanned articles or other general office applications.
2. Image Viewing: This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos and other
images with outstanding clarity in vibrant colors – all without artifacts and faded colors.
3. Entertainment: Ramped up luminance, deepened color saturation, dynamic contrast and razor sharpness displays every details in
darker areas of your videos without color washout in brighter areas maintaining a dynamic natural values for the ultimate video display.
4. Economy: Under this profile, brightness, contrast are adjusted and backlighting fine-tuned for just right display of everyday office
applications and lower power consumption.
5. Off: No optimization by SmartImage.
RETURN TO TOP OF THE PAGE
SmartContrast
What is it?
Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor's contrast ratio for maximum visual
clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter images or dimming backlighting for clear display of
images on dark backgrounds.
Why do I need it?
You want the very best visual clarity and viewing comfort for every type of content. SmartContrast dynamically controls contrast and adjusts
backlighting for clear, crisp, bright gaming and video images or displays clear, readable text for office work. By reducing your monitor's power
consumption, you save on energy costs and extend the lifetime of your monitor.
How does it work?
When you active SmartContrast which will analysis the content you are displaying in real time to adjust colors and control backlight intensity. This
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 3／11 页）2009-8-13 14:54:38
Product Information
function can obviously enhance contrast in dynamic for more entertainment fun when viewing videos or playing games.
RETURN TO TOP OF THE PAGE
SmartSaturate
What is it?
Smart technology that controls color saturation - the degree to which one on screen color is diluted by neighboring colors - to deliver rich and
vibrant images for more entertainment fun when you are viewing videos.
Why do I need it?
You want rich, vibrant images for more entertainment fun when viewing photos or videos.
How does it work?
SmartSaturate dynamically controls color saturation – the degree to which on-screen color is diluted by neighboring colors – to deliver rich,
vibrant display for more entertainment fun when you are viewing images or videos in your display's Entertainment mode and is turned off for top
quality display of office application and in the Economy mode to reduce power consumption.
RETURN TO TOP OF THE PAGE
SmartSharpness
What is it?
Smart technology that enhances sharpness when you need it for ultimate display performance and more entertainment fun when you are viewing
videos or photos.
Why do I need it?
You want the ultimate in sharpness for more entertainment fun when viewing photos or videos.
How does it work?
Smart technology enhances sharpness when you need it for ultimate display performance and more entertainment fun when you are viewing
videos or photos in the Entertainment mode and is turned off for top quality display of office applications and in the Economy mode to reduce
power consumptions.
RETURN TO TOP OF THE PAGE
Technical Specifications*
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 4／11 页）2009-8-13 14:54:38
Product Information
Picture/Display
• LCD panel type TFT-LCD
• Panel size 19"
• Aspect ratio 16:10
• Pixel Pitch 0.2835 x 0.2835 mm
• Brightness 250 cd/m²
•SmartContrast 25000:1
•Contrast ratio(typ.) 800:1
• Response time (typical) 5 ms
• Optimum Resolution 1440 x 900 @ 60Hz
• Viewing angle 176° (H) / 170° (V) @ C/R > 5
• Picture Enhancement Smartimage
• Display colors 16.7 M
• Scanning Frequency 30 - 83 kHz (H)/56 -75Hz (V)
• sRGB YES
Connectivity
• Signal input
• Input Signal Separate Sync, Sync on Green
Convenience
• User Convenience Smartimage, Auto(Back),Input(Down), Brightness(Up),Menu(OK), Power On/Off
• OSD Languages English, French, German, Italian, Russian, Spanish, Simplified Chinese, Portuguese
• Other convenience VESA mount ( 100 x 100mm), Kensington lock
• Plug & Play Compatibility DDC/CI, sRGB, Windows 98/2000/XP/Vista, Mac OS X
Stand
• Height adjustment 70 mm (190S1CB/190S1CS models)
• Swivel -45/+45 (190S1CB/190S1CS models)
• Tilt -5/+20
Power
• On mode < 19 W (typ.),< 22.8 W (max.)
• On mode (ECO mode) < 14.5 W (typ.)
Energy Consumption (EnergyStar 5.0
test method) AC Input Voltage at 100VAC
+/-5VAC, 50Hz +/- 3Hz AC Input Voltage at 115VAC
+/-5VAC, 60Hz +/- 3Hz AC Input Voltage at 230VAC
+/-5VAC, 50Hz +/ -3Hz
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 5／11 页）2009-8-13 14:54:38
DVI-D (digital, HDCP, available for selective models), VGA (Analog)
Product Information
Normal Operation 16.6 W 16.6 W 16.7 W
Sleep 0.8 W 0.8 W 0.8 W
Off 0.5 W 0.5 W 0.5 W
Heat Dissipation* AC Input Voltage at 100VAC
+/-5VAC, 50Hz +/ -3Hz AC Input Voltage at 115VAC
+/-5VAC, 60Hz +/ -3Hz AC Input Voltage at 230VAC
+/-5VAC, 50Hz +/ -3Hz
Normal Operation 56.7BTU/hr 56.7BTU/hr 57.0BTU/hr
Sleep 2.7BTU/hr 2.7BTU/hr 2.7BTU/hr
Off 1.7BTU/hr 1.7BTU/hr 1.7BTU/hr
• Power LED indicator On mode: White, Standby/Sleep mode: White (blinking)
• Power Supply Build-in, 100-240VAC, 50/60Hz
Dimension
• Product with stand ( WxHxD) 436x372x183mm
• Product without stand ( WxHxD) 436x305x68mm
• Box dimension ( WxHxD) 488x420x141mm
Weight
• Product with stand 3.65kg
• Product without stand 3.31kg
• Product with packaging 5.27kg
Operating Condition
• Temperature range (operation) 0° C to 40 ° C
• Temperature range (operation) -20° C to 60° C
• Relative humidity 20% to 80%
• Altitude Non-operation: + 12,000 ft ( 3,658 m)
operation: + 40,000 ft ( 12,192 m),
• MTBF 50000 hrs
Environmental
• ROHS YES
• EPEAT sliver
• EnergyStar 5.0
• Packaging 100% recyclable
Compliance and standards
• Regulatory Approvals CE Mark, Energy Star 5.0, FCC Class B, SEMKO, TCO'03, TÜV/GS, TÜV Ergo, UL/cUL
Cabinet
• Color Sliver/Black, Black/Black
• Finish Texture
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 6／11 页）2009-8-13 14:54:38
Product Information
* This data is subject to change without notice.
RETURN TO TOP OF THE PAGE
Resolution & Preset Modes
A. Maximum Resolution
- For 190S1
1440 x 900 at 75 Hz (analog input)
1440 x 900 at 75 Hz (digital input)
B. Recommended Resolution
- For 190S1
1440 x 900 at 60 Hz (digital input)
1440 x 900 at 60 Hz (analog input)
13 factory preset modes:
H. freq (kHz) Resolution V. freq (Hz)
31.469 720*400 70.087
31.469 640*480 59.940
35.000 640*480 67.000
37.500 640*480 75.000
38.879 800*600 60.317
46.875 800*600 75.00
49.70 832*624 75.000
48.363 1024*768 60.004
60.023 1024*768 75.029
63.981 1280*1024 60.020
79.976 1280*1024 75.025
55.935 1440*900 59.887
70.635 1440*900 74.984
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 7／11 页）2009-8-13 14:54:38
Product Information
Automatic Power Saving
If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption
when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically. The following table
shows the power consumption and signaling of this automatic power saving feature:
Power Management Definition
VESA Mode Video H-sync V-sync Power Used LED color
Active ON Yes Yes < 19 W (typ.),< 22.8 W
(max.) White
Sleep OFF No No < 0.8 W (typ.) White
(Blinking)
Switch Off OFF - - < 0.5W (typ.) Off
This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, we have
determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
* This data is subject to change without notice.
The native resolution of the monitor is 1440 x 900, By default, your monitor has 100% (max.) 50% contrast, and 6500K
color temperature, with full white pattern.
RETURN TO TOP OF THE PAGE
Product Views
Follow the links to see various views of the monitor and its components.
Front View Product Description
RETURN TO TOP OF THE PAGE
Physical Function
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 8／11 页）2009-8-13 14:54:38
Product Information
1) Tilt
2) Swivel (190S1CB/190S1CS models)
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 9／11 页）2009-8-13 14:54:38
Product Information
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/product.htm（第 11／11 页）2009-8-13 14:54:38
Philips Pixel Defect Policy
• Product Features
• Technical Specifications
• Resolution & Preset Modes
• Automatic Power Saving
• Physical Specification
• Pin Assignment
• Product Views
Philips Pixel Defect Policy
Philips' Flat Panel Monitors Pixel Defect Policy
Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing
processes and practice stringent quality control. However, pixel or sub pixel defects on the TFT LCD panels used in flat
panel monitors are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects,
but Philips guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under
warranty. This notice explains the different types of pixel defects and defines acceptable defect levels for each type. In
order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel must exceed
these acceptable levels. For example, no more than 0.0004% of the sub pixels on a 19" XGA monitor may be defective.
Furthermore, Philips sets even higher quality standards for certain types or combinations of pixel defects that are more
noticeable than others. This policy is valid worldwide.
Pixels and Sub pixels
A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. Many pixels
together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single
white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of
lit and dark sub pixels appear as single pixels of other colors.
Types of Pixel Defects
Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several
types of sub pixel defects within each category.
Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is, a bright dot is a
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/pixel.htm（第 1／4 页）2009-8-13 14:54:42
Philips Pixel Defect Policy
sub-pixel that stands out on the screen when the monitor displays a dark pattern. There are the types of bright dot defects:
One lit red, green or blue sub pixel
Two adjacent lit sub pixels:
- Red + Blue = Purple
- Red + Green = Yellow
- Green + Blue = Cyan (Light Blue)
Three adjacent lit sub pixels (one
white pixel)
A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green
bright dot is 30 percent brighter than neighboring dots.
Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That is, a dark dot is a
sub-pixel that stands out on the screen when the monitor displays a light pattern. These are the types of black dot defects:
One dark sub pixel Two or three adjacent dark sub pixels
Proximity of Pixel Defects
Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also
specifies tolerances for the proximity of pixel defects.
Pixel Defect Tolerances
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/pixel.htm（第 2／4 页）2009-8-13 14:54:42
Philips Pixel Defect Policy
In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips
flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
BRIGHT DOT DEFECTS ACCEPTABLE LEVEL
MODEL 190S1
1 lit subpixel 3
2 adjacent lit subpixels 1
3 adjacent lit subpixels (one white pixel) 0
Distance between two bright dot defects* >15mm
Total bright dot defects of all types 3
BLACK DOT DEFECTS ACCEPTABLE LEVEL
MODEL 190S1
1 dark subpixel 5 or fewer
2 adjacent dark subpixels 2 or fewer
3 adjacent dark subpixels 0
Distance between two black dot defects* >15mm
Total black dot defects of all types 5 or fewer
TOTAL DOT DEFECTS ACCEPTABLE LEVEL
MODEL 190S1
Total bright or black dot defects of all types 5 or fewer
Note:
* 1 or 2 adjacent sub pixel defects = 1 dot defect
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/pixel.htm（第 3／4 页）2009-8-13 14:54:42
SmartControl
• Product Information
• Philips Pixel Defect Policy
•Philips SmartControl ll
• System support and requirement
• Installation
• Start to use
• Q&A
SmartControl II (Selective Models)
Philips SmartControl II
SmartControl II is monitor-based software with an easy-to-use on-screen graphic interface that guides you through fine-tuning resolution, color
calibration and other display settings including brightness, contrast, clock & phase, position, RGB, white point and - on models with onboard speakers -
volume adjustments.
System support and requirement:
1. Sytem support: 2000, XP, NT 4.0, XP 64 Edition, Vista 32/64. IE Support 6.0/7.0.
2. Language support: English, Simplified Chinese, German, Spanish, French, Italian, Russian, Portuguese.
3. Philips Monitor support DDC/CI Interface.
Installation:
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 1／17 页）2009-8-13 14:54:49
SmartControl
● Follow the instruction and complete the installation.
● You can lauch after installation complete.
● If you want to launch later, you can either click the shortcut on desktop or toolbar.
Start to use:
1. First launch -Wizard
● The first time after installation of SmartControl II, it will automatically go to Wizard for first time launch.
● The wizard will guide you through adjustment your monitor performance step by step.
● You can go to Plug-in menu to launch wizard later on as well.
● You can adjust more options without wizard by Standard pane.
Wizard Analog Sequence Wizard Digital Sequence
Resolution Resolution
Focus Contrast
Brightness Brightness
Contrast White Point (Color Temp)
Position File
White Point (Color Temp) -
File -
2. Start with Standard pane:
Adjust menu:
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 2／17 页）2009-8-13 14:54:49
SmartControl
● Adjust Menu allow you to adjust Brightness, Contrast, Focus, Position and Resolution.
● You can follow the instruction and do the adjustment.
● Cancel prompts user if you want to cancel installation.
Tab Heading Sub Menu Display in Analog Display in Digital
Adjust Brightness Yes Yes
Adjust Contrast Yes Yes
Adjust Focus (Clock & Clock Phase) Yes No
Adjust Position Yes No
Adjust Resolution Yes Yes
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 3／17 页）2009-8-13 14:54:49
SmartControl
Color menu:
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 4／17 页）2009-8-13 14:54:49
SmartControl
● Color Menu allow you to adjust RGB, Black Level, White Point, Color Calibration, and SmartImage (Please
refer to SmartImage section).
● You can follow the instruction and do the adjustment.
● Refer to below table for sub-menu item base on your input.
● Example for Color Calibration
Tab Heading Sub Menu Display in Analog Display in Digital
Color RGB Yes Yes
Color Black Level Yes Yes
Color White Point Yes Yes
Color Color Calibration Yes Yes
Color Viewing Mode Yes Yes
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 5／17 页）2009-8-13 14:54:49
SmartControl
1. "Show Me" starts color calibration tutorial.
2. Start - starts the 6-step color calibration sequence.
3. Quick View loads the before/after images.
4. To return to Color home pane, click the Cancel button.
5. Enable color calibration - by default is on. If unchecked, does not allow for color calibration to happen, dimes out start and quick view buttons.
6. Must have patent info in calibration screen.
First color Calibration Screen:
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 6／17 页）2009-8-13 14:54:49
SmartControl
1. Previous button is disabled until the second color screen.
2. Next goes to the succeeding target (6-targets).
3. Final next goes File>Presets pane.
4. Cancel closes the UI and returns to the plug in page.
SmartImage - Allows user to change setting for better display setting based on content.
When Entertainment is set, SmartContrast and SmartResponse are enabled.
Plug-Ins - Asset Management Pane will only be active when selecting Asset Management from the drop-down Plug Ins
menu.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 7／17 页）2009-8-13 14:54:49
SmartControl
Displays Assent Management information on Managment, Description, Serial Number, Current Timing, Domain Name, and Asset Management Status.
To return to Plug-in home pane select the plug-in tab.
Plug-Ins - Theft Deterrence Pane will only be active when selecting Theft Deterrence Mode from the drop-down Plug Ins
menu.
To enable Theft Deterrence, clicking Enable Theft Mode button brings up the following screen:
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 8／17 页）2009-8-13 14:54:49
SmartControl
1. User can enter PIN between 4 and 9 digits numbers only.
2. After entering PIN, Accept button takes user to the pop-up dialog box on the following page.
3. Minimum minutes set to 5. Slider set to 5 by default.
4. Does not require the display be attached to a different host to go into theft mode.
Once a PIN is entered and accepted, the following dialog box appears:
● Click on No button takes user to the following screen.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 9／17 页）2009-8-13 14:54:49
SmartControl
● Click on Yes button takes user to secure web site landing page.
After creating PIN, the Theft Deterrence pane will indicate Theft Deterrence Enabled and provide PIN Options button:
1. Theft Deterrence Enabled is displayed.
2. Disable Theft Mode opens pane screen on next page.
3. PIN Options button only available after user creates PIN, button opens secure PIN web site.
Disable Theft button opens the following pane:
1. After entering PIN, Accept button disables PIN.
2. Cancel button opens up main Theft Deterrence pane, displaying Theft Deterrence Disabled. Enable Theft Mode and PIN Options buttons.
3. Entering incorrect PIN results in the following dialog box:
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 10／17 页）2009-8-13 14:54:49
SmartControl
Options>Preferences - Will only be active when selecting Preferences from the drop-down Options menu. On a non-
supported display capable of DDC/CI, only the Help and Options tabs are available.
1. Displays current preference settings.
2. A checked box enables the feature. The check box is a toggle.
3. Enable Context Menu on desktop is checked (On) by default. Enable Context menu displays SmartControl II selections for Select Preset and Tune
Display in the desktop right-click context menu. Disabled removes SmartControl II from the right click context menu.
4. Enable Task Tray icon is checked (On) by default. Enable context menu shows the task tray menu for SmartControl II. A right click on the task tray icon
displays the menu options for Help, Technical Support. Check for Upgrade, About, and Exit. When Enable task tray menu is disabled, the task tray icon
will only display EXIT.
5. Run at Startup is checked (On) by default. When disabled, SmartControl II will not launch at start or be in the task tray. The only way to launch
SmartControll II is either from the desktop short cut or from the program file. Any preset set to run at startup will not load when this box is unchecked
(Disabled).
6. Enable transparency mode (Vista, XP, and 2k only). Default is 0% Opaque.
Options>Input - Will only be active when selecting Input from the drop-down Options menu. On a non-supported display
capable of DDC/CI, only the Help and Options tabs are available. All other SmartControl II tabs are not available.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 11／17 页）2009-8-13 14:54:49
SmartControl
1. Display the Source instruction pane and current input source setting.
2. On single input displays, this pane will not be visible.
Options>Audio - Will only be active when selecting Volume from the drop-down Options menu.
On a non-supported display capable of DDC/CI, only the Help and Options tabs are available.
Option>Auto Pivot
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 12／17 页）2009-8-13 14:54:49
SmartControl
Help>User Manual - Will only be active when selecting User Manual from the drop-down Help menu. On a non-supported
display capable of DDC/CI, only the Help and Options tabs are available.
Help>Version - Will only be active when selecting Version from the drop- down Help menu. On a non-supported display
capable of DDC/CI, only the Help and Options tabs are available.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 13／17 页）2009-8-13 14:54:49
SmartControl
Context Sensitive menu
The Context Sensitive menu is Enabled by default. If Enable Context Menu has been checked in the Options>Preferences pane, then the menu will be visible.
The Context Menu has four entries:
1. SmartControll II - When selected the About Screen is displayed.
2. Select Preset - Provides a hierarchical menu of saved presets for immediate use. A check mark shows the currently selected preset. Facoty Preset can
also be called from the drop down menu.
3. Tune Display - Opens the SmartControl II control panel.
4. Fly off for SmartImage - Check current settings, Off, Office Work, ImageViewing, Entertainment, Economy.
Task Tray Menu Enabled
The task tray menu can be displayed by right-clicking on the SmartControl II icon from the task tray. Left Click will launch the application.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 14／17 页）2009-8-13 14:54:49
SmartControl
The task tray has five entries:
1. Help - Access to User Manual file: opnes User Manual file using the default browser window.
2. Technical Support - displays the tech support page.
3. Check for Update - takes the user to PDI Landing and checks the user's version against the most current available.
4. About - Displays detailed reference information: product version, release information, and product name.
5. Exit - Close SmartControll II. To run SmartControll II again either select SmartControll II from Program menu, double-click the desktop PC icon or restart
the system.
Task Tray Menu Disabled
When the Task Tray is disabled in the preference folder, only the EXIT selection is available. To completely remove SmartControll II from the task tray, disable
Run at Startup in Options>Preferences.
Q&A
Q1. I change the monitor on a PC to a different one and the SmartControl becomes un-usable, what do I do?
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 15／17 页）2009-8-13 14:54:49
SmartControl
A. Restart your PC and see if SmartControl can work. Otherwise, you will need to remove and re-install SmartControl to ensure proper driver is installed.
Q2. The SmartControl functions well at the beginning, but it is not workable, what can I do?
A. If the following actions were executed, the monitor driver may need to be re-installed.
● Change video graphic adapter to another one
● Update video driver
● Activities on OS, such as service pack or patch
● Run Windows Update and updated monitor and/or video driver
● Windows was booted with the monitor power off or disconnected.
To find out, please right click My Computer and click on Properties->Hardware-> Device Manager.
If you see "Plug and Play Monitor" shows under Monitor, then you need to re-install. Simply remove SmartControl and re-install it.
Q3. After installing SmartControl, when clicking on SmartControl tab, nothing shows up after a while or a failure message shows, what happened?
A. It might be your graphic adaptor is not compatible with the SmartControl. If your graphic adaptor is one of the above mentioned brands, try to download the
most updated graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove SmartControl, and re-install it once more.
If it is still not working, we are sorry that the graphic adaptor is not supported. Please pay attention to Philips’ web site for any updated SmartControl driver
available.
Q4. When I click on Product Information, only partial information is shown, what happened?
A. It might be your graphic card adaptor driver is not the most updated version which fully supporting DDC/CI interface. Please try to download the most updated
graphic adaptor driver from corresponding companies’ web site. Install the driver. Remove SmartControl, and re-install it once more.
Q5. I forgot my PIN for Theft Deterrence Function. How can I do?
A. Please contact IT manager or Philips Service Center.
Q6. In a monitor with the Smartlmage feature, the sRGB scheme of color temperature function in SmartControl is not responding, why?
A. When Smartlmage is enabled, the sRGB scheme is disabled automatically. To use sRGB, you need to disable Smartlmage with the button at the front
bezel of your monitor.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 16／17 页）2009-8-13 14:54:49
SmartControl
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/product/SMART.HTM（第 17／17 页）2009-8-13 14:54:49
Installing Your LCD Monitor
• Front View Produt Description
• Connecting to Your PC
• The Base
• Getting Started
• Optimizing Performance
Installing Your LCD Monitor
Front View Product Description
1 To switch monitor's power On and Off
2MENU/ To access OSD menu
3 To adjust the OSD menu
4To adjust brightness of the display
5INPUT .To change the signal input source.
6 / AUTO Return to previous OSD level / Automatically adjust the horizontal position, vertical
position, phase and clock settings.
7Smartlmage. There are five modes to be selected: Office Work, Image Viewing,
Entertainment, Economy, and Off.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/install.htm（第 1／3 页）2009-8-13 14:54:52
Installing Your LCD Monitor
Rear View
1 Kensington anti-thief lock
2 VGA input
3 DVI-D input (available for selective models)
4 AC power input
RETURN TO TOP OF THE PAGE
Optimizing Performance
● For best performance, ensure that your display settings are set at 1440x900, 60Hz.
Note: You can check the current display settings by pressing the 'OK' button
once. The current display mode is shown in OSD main controls called
RESOLUTION.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/install.htm（第 2／3 页）2009-8-13 14:54:52
Connecting to Your PC
• Front View Product Description
• Accessory Pack
• Connecting to Your PC
• Getting Started
• Optimizing Performance
• The base
Connecting to Your PC
Accessory Pack
Unpack all the parts.
Power cord DVI cable (Optional)
VGA cable EDFU pack
RETURN TO TOP OF THE PAGE
Connecting to Your PC
1) Connect the power cord to the back of the monitor firmly. (Philips has pre-connected VGA cable for the
first installation.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/connect.htm（第 1／3 页）2009-8-13 14:54:55
Connecting to Your PC
* available for selective models
* available for selective models
2) Connect to PC
(a) Turn off your computer and unplug its power cable.
(b) Connect the monitor signal cable to the video connector on the back of your computer.
(c) Plug the power cord of your computer and your monitor into a nearby outlet.
(d) Turn on your computer and monitor. If the monitor displays an image, installation is complete.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/connect.htm（第 2／3 页）2009-8-13 14:54:55
Connecting to Your PC
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/connect.htm（第 3／3 页）2009-8-13 14:54:55
The Base
:
• Front View Product Description
• Accessory Pack
• Setting up and connecting your
monitor
• Getting Started
• Optimizing Performance
• Attach the Base
• Remove the Base Stand
• Remove the Base
The Base
Attach the Base
1) Firmly grasp the monitor with both hands. Attach the monitor stand to the monitor column until the tabs "click" into place before
releasing the height adjustable column.
190S1CB/190S1CS models
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/base.htm（第 1／6 页）2009-8-13 14:54:59
The Base
RETURN TO TOP OF THE PAGE
Remove the base stand
Before you start disassembling the monitor base, please follow the instructions below to avoid damage or injury.
a) Extend the monitor stand to its maximum height.
(b) Place the monitor face down on a smooth surface, taking care to avoid scratching or damaging the screen. Then lift the
monitor stand.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/base.htm（第 2／6 页）2009-8-13 14:54:59
The Base
(c) Press the release button on the rear of the stand to remove the base from the stand.
Remove the base
Condition:
● for VESA standard mounting applications
(a) Remove the 4 screw covers.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/base.htm（第 3／6 页）2009-8-13 14:54:59
The Base
(b) Remove the 4 Screws and then remove the base from the LCD monitor.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/base.htm（第 4／6 页）2009-8-13 14:54:59
The Base
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/base.htm（第 6／6 页）2009-8-13 14:54:59
Getting Started
Your LCD Monitor :
• Front View Product Description
• Setting Up and Connecting Your
Monitor
• Getting Started
• Optimizing Performance
Getting Started
Getting Started
Use the information file ( .inf) for Windows® 2000/XP/Vista or later
The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for Windows® 2000/XP/
Vista. This information file ( .inf) should be installed in order that your Philips monitor can be enabled from the
'Monitor' dialog box in Windows® 2000/XP/Vista and the Plug & Play application can be activated. The installation
procedure based on Windows® 2000 , XP and Vista is specified as follows.
For Windows® 2000
1. Start Windows® 2000
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select 'Monitor'
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below.
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.
7. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on
'Next' and then click on 'Have disk...'.
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).
9. Click on the 'Open' button, then click on the 'OK' button.
10. Select your monitor model and click on the 'Next' button.
11. Click on the 'Finish' button then the 'Close' button.
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
For Windows® XP
1. Start Windows® XP
2. Click on the 'Start' button and then click on 'Control Panel'.
3. Select and click on the category 'Printers and Other Hardware'
4. Click on the 'Display' Item.
5. Select the 'Settings' tab then click on the 'Advanced' button.
6. Select 'Monitor' tab
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.
- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/gt_start.htm（第 1／2 页）2009-8-13 14:55:03
Getting Started
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive F:
(CD-ROM Drive).
11. Click on the 'Open' button, then click the 'OK' button.
12. Select your monitor model and click on the 'Next' button.
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with Windows® XP'
message, please click on the 'Continue Anyway' button.
13. Click on the 'Finish' button then the 'Close' button.
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties dialog box.
For Windows® Vista
1. Start Windows® Vista
2. Click the Start button; select and click on 'Control Panel'.
3. Select and click on 'Hardware and Sound'
4. Choose 'Device Manager' and Click on 'Update device drivers'.
5. Select 'Monitor' and then right click on 'Generic PnP Monitor'.
6. Click on 'Update Driver Software'.
7. Select 'Browse my computer for driver software'.
8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:(CD-ROM Drive:\\Lcd
\PC\drivers\).
9. Click the 'Next' button.
10. Wait few minutes for installing the driver, and then click 'Close' button.
If your Windows® 2000/XP/Vista version is different or you need more detailed installation information, please refer to
your Windows® 2000/XP/Vista user's manual.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/install/gt_start.htm（第 2／2 页）2009-8-13 14:55:03
On-Screen Display
•Description of the On-Screen Display
• The OSD Tree
On-Screen Display
Description of the On Screen Display
What is the On-Screen Display?
On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or
select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display
interface is shown as below :
In the OSD shown above users can press buttons at the front bezel of the monitor to
move the cursor, to confirm the choice or change.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/osd/osddesc.htm（第 1／3 页）2009-8-13 14:55:13
On-Screen Display
The OSD Tree
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to
work your way around the different adjustments later on.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/osd/osddesc.htm（第 2／3 页）2009-8-13 14:55:13
On-Screen Display
Resolution notification
This monitor is designed for optimal performance at its native resolution, 1440X900@60Hz. When the monitor is powered
on at a different resolution, an alert is displayed on screen: Use 1440x900@60Hz for best results.
Display of the native resolution alert can be switched off from Setup in the OSD (On Screen Display) menu.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/190S1/osd/osddesc.htm（第 3／3 页）2009-8-13 14:55:13
Customer Care & Warranty
Customer Care & Warranty
PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE
WESTERN EUROPE: Austria Belgium Denmark France Germany
Greece Finland Ireland Italy Luxembourg the Netherlands Norway
Portugal Sweden Switzerland Spain United Kingdom Poland
EASTERN EUROPE: Czech Republic Hungary Russia Slovakia Slovenia
Turkey
LATIN AMERICA: Argentina Brasil
NORTH AMERICA: CANADA USA
PACIFIC: Australia New Zealand
ASIA: China Hong Kong India Indonesia Korea Malaysia Pakistan
Philippines Singapore Taiwan Thailand Vietnam
AFRICA: South Africa
MIDDLE EAST: United Arab Emirates
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warranty.htm2009-8-13 14:55:16
Your Philips F1rst Choice Warranty
Your Philips F1rst Choice Warranty
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and deliver high-quality
performance, ease of use and ease of installation. Should you encounter any difficulties while
installing or using this product, please contact the Philips helpdesk directly to benefit from your Philips
F1rst Choice Warranty. This three-year service warranty entitles you to a swap model on-site if your
monitor turns out to be faulty or defective. Philips aims at a swap within 48 hours of your call being
received.
What is covered?
The Philips F1rst Choice Warranty applies within Andorra, Austria, Belgium, Cyprus, Denmark, France, Germany, Greece,
Finland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, the Netherlands, Norway, Poland, Portugal, Sweden,
Switzerland, Spain and the United Kingdom and only for monitors originally designed, manufactured, approved and/or
authorized for usage within these countries.
Warranty coverage begins as from the day you buy your monitor. For three years thereafter, your monitor will be
swapped by at least an equivalent monitor in case of defects provided for under the warranty coverage.
The swap monitor remains yours and Philips keeps the defective/original monitor. For the swap monitor the warranty
period remains equal to that of your original monitor, being 36 months as from the purchase date of your original monitor.
What is excluded?
The Philips F1rst Choice Warranty applies provided the product is handled properly for its intended use, in accordance
with its operating instructions and upon presentation of the original invoice or cash receipt, indicating the date of purchase,
dealer's name and model and production number of the product.
The Philips F1rst Choice Warranty may not apply if:
● The documents have been altered in any way or made illegible;
● The model or production number on the product has been altered, deleted, removed or made illegible;
● Repairs or product modifications and alterations have been executed by unauthorized service organizations or
persons;
● Damage is caused by accidents including but not limited to lightning, water or fire, misuse or neglect;
● Reception problems caused by signal conditions or cable or antenna systems outside the unit;
● Defects caused by abuse or misuse of the monitor;
● Product requires modification or adaptation to enable it to comply with local or national technical standards, which
apply in countries for which the product was not originally designed, manufactured, approved and/or authorized.
Therefore always check whether a product can be used in a specific country.
● Note that products that are not originally designed, manufactured, approved and/or authorized for usage within the
Philips F1rst Choice countries, do not apply to the Philips F1rst Choice Warranty. In these cases the Philips global
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/war_1st.htm（第 1／2 页）2009-8-13 14:55:18
Your Philips F1rst Choice Warranty
warranty terms are valid.
Just a click away
In case of any problems, we advise you to read the operating instructions carefully or go to the www.philips.com/support
website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions carefully or go to the www.
philips.com/support website for additional support before contacting the Philips helpdesk.
To solve your problem quickly, please prepare the following details before contacting the Philips helpdesk:
● Philips type number
● Philips serial number
● Purchase date (copy of purchase may be required)
● PC environment Processor:
❍ CUP and Graphic card name and driver version
❍ Operating system
❍ Application being used
● Other cards installed
Having the following information available will also help speed up the process:
● Your proof of purchase indicating: date of purchase, dealer name, model and product serial number.
● The full address to which the faulty monitor has to be collected and the swap model should be delivered.
Philips' customer help desks are located worldwide. Click here to access the F1rst Choice Contact Information.
Or you can reach us via:
Website: http://www.philips.com/support
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/war_1st.htm（第 2／2 页）2009-8-13 14:55:18
F1rst Choice Contact Information
F1rst Choice Contact Information
Country Code Telephone number Tariff
Austria +43 0810 000206 € 0.07
Belgium +32 078 250851 € 0.06
Denmark +45 3525 8761 Local call tariff
Finland +358 09 2290 1908 Local call tariff
France +33 082161 1658 € 0.09
Germany +49 01803 386 853 € 0.09
Greece +30 00800 3122 1223 Free of charge
Ireland +353 01 601 1161 Local call tariff
Italy +39 840 320 041 € 0.08
Luxembourg +352 26 84 30 00 Local call tariff
The Netherlands +31 0900 0400 063 € 0.10
Norway +47 2270 8250 Local call tariff
Poland +48 0223491505 Local call tariff
Portugal +351 2 1359 1440 Local call tariff
Spain +34 902 888 785 € 0.10
Sweden +46 08 632 0016 Local call tariff
Switzerland +41 02 2310 2116 Local call tariff
United Kingdom +44 0207 949 0069 Local call tariff
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warfirst.htm2009-8-13 14:55:21
Your Guarantee in Central and Eastern Europe
Your Guarantee in Central and Eastern Europe
Dear Customer,
Thank you for purchasing this Philips product, which has been designed and manufactured to the highest quality
standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and
replacement parts during a period of 36 months from date of purchase.
What is covered?
This Philips Guarantee in Central and Eastern Europe applies within Czech Republic, Hungary, Slovakia, Slovenia,
Russia and Turkey and only for monitors originally designed, manufactured, approved and/or authorized for usage within
these countries.
Warranty coverage begins as from the day you buy your monitor. For 3 years thereafter, your monitor will be
serviced in case of defects provided for under the warranty coverage.
What is excluded?
The Philips guarantee applies provided the product is handled properly for its intended use, in accordance with its
operating instructions and upon presentation of the original invoice or cash receipt, indicating the date of purchase,
dealer's name and model and production number of the product.
The Philips guarantee may not apply if:
● the documents have been altered in any way or made illegible;
● the model or production number on the product has been altered, deleted, removed or made illegible;
● repairs or product modifications and alterations have been executed by unauthorized service organizations or
persons;
● damage is caused by accidents including but not limited to lightning, water or fire, misuse or neglect.
● Reception problems caused by signal conditions or cable or antenna systems outside the unit;
● Defects caused by abuse or misuse of the monitor;
● Product requires modification or adaptation to enable it to comply with local or national technical standards,
which apply in countries for which the product was not originally designed, manufactured, approved and/or
authorized. Therefore always check whether a product can be used in a specific country.
Please note that the product is not defective under this guarantee in the case where modifications become necessary in
order for the product to comply with local or national technical standards which apply in countries for which the product
was not originally designed and/or manufactured. Therefore always check whether a product can be used in a specific
country.
Just a click away
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/war_ee.htm（第 1／2 页）2009-8-13 14:55:25
Your Guarantee in Central and Eastern Europe
In case of any problems, we advise you to read the operating instructions carefully or go to the www.philips.com/support
website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions carefully before contacting
our dealers or Information Centers
In case your Philips product is not working correctly or is defective, please contact your Philips dealer or directly the
Philips Service and Consumer Information Centers
Website: http://www.philips.com/support
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/war_ee.htm（第 2／2 页）2009-8-13 14:55:25
Consumer Information Centers
Consumer Information Centers
Argentina Australia Brasil Canada New Zealand Belarus Bulgaria
Croatia Czech Republic Estonia United Arab Emirates Hong Kong
Hungary India Indonesia Israel Latvia Lithuania Malaysia
Middle East + North Africa New Zealand Pakistan Romania Russia
Serbia & Montenegro Singapore Slovakia Slovenia South Africa
South Korea Taiwan Philippines • Thailand Turkey Ukraine Vietnam
Eastern Europe
BELARUS
Technic al Center of JV IBA
M. Bogdanovich str. 155
BY - 220040 Minsk
Tel: +375 17 217 33 86
BELARUS
Service.BY
Petrus Brovky st. 19 – 101-B
220072, Minsk
Belarus
BULGARIA
LAN Service
140, Mimi Balkanska Str.
Office center Translog
1540 Sofia, Bulgaria
Tel: +359 2 960 2360
www.lan-service.bg
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warcic.htm（第 1／9 页）2009-8-13 14:55:29
Consumer Information Centers
CZECH REPUBLIC
General Consumer Information Center
800 142100
Xpectrum
Lu.ná 591/4
CZ - 160 00 Praha 6 Tel: 800 100 697 or 220 121 435
Email:info@xpectrum.cz
www.xpectrum.cz
CROATIA
Renoprom d.o.o.
Ljubljanska 4,
Sv. Nedjelja,10431
Croatia
Tel: +385 1 333 0974
ESTONIA
FUJITSU SERVICES OU
Akadeemia tee 21G
EE-12618 Tallinn
Tel: +372 6519900
www.ee.invia.fujitsu.com
HUNGARY
Serware Szerviz
Vizimolnár u. 2-4
HU - 1031 Budapest
Tel: +36 1 2426331
Email: inbox@serware.hu
www.serware.hu
HUNGARY
Profi Service Center Ltd.
123 Kulso-Vaci Street,
H-1044 Budapest ( Europe Center )
Hungary
Tel: +36 1 814 8080
m.andras@psc.hu
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warcic.htm（第 2／9 页）2009-8-13 14:55:29
Consumer Information Centers
LATVIA
ServiceNet LV
Jelgavas iela 36
LV - 1055 Riga,
Tel: +371 7460399
Email: serviss@servicenet.lv
LITHUANIA
ServiceNet LT
Gaiziunu G. 3
LT - 3009 KAUNAS
Tel: +370 7400088
Email: servisas@servicenet.lt
www.servicenet.lt
ROMANIA
Blue Ridge Int'l Computers SRL
115, Mihai Eminescu St., Sector 2
RO - 020074 Bucharest
Tel: +40 21 2101969
SERBIA & MONTENEGRO
Kim Tec d.o.o.
Viline vode bb, Slobodna zona
Beograd L12/3
11000 Belgrade
Serbia
Tel. +381 11 20 70 684
SLOVAKIA
General Consumer Information Center
0800004551
Datalan Servisne Stredisko
Puchovska 8
SK - 831 06 Bratislava
Tel: +421 2 49207155
Email: servis@datalan.sk
SLOVENIA
PC HAND
Brezovce 10
SI - 1236 Trzin
Tel: +386 1 530 08 24
Email: servis@pchand.si
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warcic.htm（第 3／9 页）2009-8-13 14:55:29
Consumer Information Centers
RUSSIA
CPS
18, Shelepihinskaya nab.
123290 Moscow
Russia
Tel. +7(495)797 3434
Profservice:
14A -3, 2Karacharovskaya str,
109202, Moscow ,
Russia
Tel. +7(095)170-5401
TURKEY
Türk Philips Ticaret A.S.
Yukari Dudullu Org.San.Bolgesi
2.Cadde No:22
34776-Umraniye/Istanbul
Tel: (0800)-261 33 02
UKRAINE
Comel
Shevchenko street 32
UA - 49030 Dnepropetrovsk
Tel: +380 562320045
www.csp-comel.com
LLC Topaz Company
Topaz-Service Company,
Mishina str. 3,
Kiev
Ukraine-03151
Tel: +38 044 245 73 31
Latin America
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warcic.htm（第 4／9 页）2009-8-13 14:55:29
Consumer Information Centers
ARGENTINA
Azopardo 1480.
(C1107ADZ) Cdad. de Buenos Aires
Tel: 0800 3330 856
Email: CIC.monitores@Philips.com
BRASIL
Alameda Raja Gabaglia, 188 - 10°Andar - V.
Olímpia - S. Paulo/SP - CEP 04551-090 -
Brasil
Tel: 0800-7254101
Email: lourdes.rezende@aoc.com.br
Pacific
AUSTRALIA
Company: AGOS NETWORK PTY LTD
Address: 4/5 Dursley Road, Yenorra, NSW 2161, Australia
Tel: 1300 360 386
Fax: +61-2-80808147
Email: philips@agos.com.au
Service hours: Mon.~Fri. 8:00am-7:30pm
NEW ZEALAND
Company: Visual Group Ltd.
Address: 28 Walls Rd Penrose Auckland
Phone: 0800 657447
Fax: 09 5809607
E-mail: vai.ravindran@visualgroup.co.nz
Service Hours: Mon.~Fri. 8:30am~5:30pm
Asia
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warcic.htm（第 5／9 页）2009-8-13 14:55:29
Consumer Information Centers
HONG KONG/Macau
Company Name: PHK Service Limited
Address: Flat A, 10/F., Pak Sun Building, 103 - 107 Wo Yi Hop Road, Kwai Chung, New Territories, Hong
Kong
Tel.: (852) 2610-6908 / (852) 2610-6929 for Hong Kong and (853) 2856-2277 for Macau
Fax: (852) 2485 3574 for Hong Kong and (853) 2856 1498 for Macau
E-mail: enquiry@phkservice.com.hk
Service Hours: Mon.~Sat. 09:00am~06:00pm
India
Company: REDINGTON INDIA LTD
Address: SPL Guindy House, 95 Mount Road, Chennai 600032, India
Tel: +9144-42243352/353
E-mail: aftersales@in.aocmonitor.com
Service hours: Mon.~Fri. 9:00AM~5:30PM; Sat. 9:00AM~1:00PM
Indonesia
Company Name: PT. Gadingsari elektronika Prima
Address: Kompleks Pinang 8, Jl. Ciputat raya No. 8F, Pondok Pinang. Jakarta
Tel: 021-750909053, 021-750909056
Fax: 021-7510982
E-mail: gepta@cbn.net.id
Service hours: Mon.~Fri. 8:30am~4:30pm; Sat. 8:30am~2:00pm
Additional service points:
1. Philips Building Jl. Buncit Raya Kav 99. Jakarta Selatan.
Phone: 021-7940040, ext 1722/1724, 98249295, 70980942
2. Jl. Tanah Abang 1 no 12S. Jakarta Pusat.
Phone: 021-3455150, 34835453
3. Rukan City Home no H31, Gading Square. Jl. Bulevar Barat. Kelapa Gading. Jakarta Utara. Phone: 021-
45870601, 98131424
South Korea
Company: PCS One Korea Ltd.
Address: 112-2, Banpo-dong, Seocho-ku, Seoul, 137-040, Korea
Call Center Tel: 080-600-6600
Tel: 82 2 591 1528
Fax: 82 2 595 9688
E-mail: cic_korea@philips.com
Service hours: Mon.~Fri. 9:00AM~ 6:00PM; Sat. 9:00AM~1:00PM
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warcic.htm（第 6／9 页）2009-8-13 14:55:29
Consumer Information Centers
Malaysia
Company: After Market Solutions (CE) Sdn Bhd
Address: Lot 6. Jalan 225/51A, 46100 Petaling Jaya, Selangor DE, Malaysia.
Phone: 603 7953 3370
Philips Info Line: 1-800-880-180
Fax: 603 7953 3338
E-mail: pceinfo.my@philips.com
Service Hours: Mon.~Fri. 8:15am~5:15pm; Sat. 9:00am~1:00pm
Pakistan
Philips Consumer Service
Address: Mubarak manzil, 39, Garden Road, Saddar, Karachi-74400
Tel: (9221) 2737411-16
Fax: (9221) 2721167
E-mail: care@philips.com
Website: www.philips.com.p
Singapore
Company: Philips Electronics Singapore Pte Ltd (Philips Consumer Care Center)
Address: 620A Lorong 1 Toa Payoh, TP4 Building Level 1, Singapore 319762
Tel: (65) 6882 3999
Fax: (65) 62508037
E-mail: consumer.care.sg@philips.com
Service hours: Mon.~Fri. 9:00am~6:00pm; Sat. 9:00am~1:00pm
Taiwan
Company: FETEC.CO
Address: 3F, No.6, Lane 205, Sec. 1, Chang Hsing Rd, Lu Chu Hs, Taoyuan, Taiwan R.O.C 33800
Consumer Care: 0800-231-099
Tel: (03)2120336
Fax: (03)3129184
E-mail: knlin08@xuite.net
Service hours: Mon.~Fri. 8:30am~7:00pm
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warcic.htm（第 7／9 页）2009-8-13 14:55:29
Consumer Information Centers
Thailand
Company: Axis Computer System Co., Ltd.
Address: 1421 Soi Lardprao 94, Srivara Town In Town Soi 3 Road, Wangthonglang, Bangkok 10310 Thailand
Tel: (662) 934-5498
Fax: (662) 934-5499
E-mail: axis5@axiscomputer.co.th
Service Hours: Mon.~Fri. 08:30am~05:30pm
Vietnam
Company: Digiworld Corp
Address: 211-213 Vo Van Tan St, Ward 5, Dist.3 , Ho Chi Minh city, Vietnam
Tel: 848-38266065
Fax: 848-38267307
E-mail: Digicare@dgw.com.vn
Service hours: 8:00 to 12:00 AM and 13:30 to 17:30 PM (from Monday to Friday)
Philippines
Glee Electronics Inc
Contact nos. (632) 636-3636 / 7064028 to 29
Fax no. (632) 7064026
Receiving Centers
NEO CARE - Megamall
4th Level Cyberzone, Building B,
SM Megamall, Mandaluyong City
NEO CARE - SM North EDSA
4th Level Cyberzone, Annex Bldg.
SM City North EDSA, Quezon City
441-1610
MDR Microware Sales Inc.
Cebu Branch
N. Escario corner Clavano St., Cebu City Phils.
# 255-4415/ 255-3242/253-9361/4124864 to 67
Sun # 0922-8210045 to 46
Davao Office:
C. Arellano St., Davao City 8000
082- 225-3021/225-3022
Sun# 0922-8210015
CDO Office:
1445 Corrales Ext.,CDO City
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warcic.htm（第 8／9 页）2009-8-13 14:55:29
Consumer Information Centers
088-856-8540/856-8541
Sun # 0922-8210080
Iloilo Office:
C. Lim Comp., Gomez St., Iloilo City
# 033 338-4159/ 033 508-3741
Sun # 0922-8808850
Africa
SOUTH AFRICA
Company name: Sylvara Technologies Pty Ltd
Address: Ho Address Palm Springs Centre Christoffel Road Van Riebeeck Park Kempton Park, South Africa
Tel: +27878084456
Fax: +2711 391 1060
E-mail: customercare@philipssupport.co.za
Service hours: Mon.~ Fri. 08:00am~05:00pm
Middle East
Middle East + North Africa
Company: AL SHAHD COMPUTER L.L.C
Address: P.O.BOX: 29024, DUBAI, UNITED ARAB EMIRATES
TEL: 00971 4 2276525
FAX: 00971 4 2276242
E-mail: shahd52@eim.ae
Service hours: Sat.~Thur. 9:00am~1:00pm & 4:00pm- 8:00pm
Israel
Company: Eastronics LTD
Address: 13 Rozanis St. P.O.B. 39300, Tel Aviv 61392 Israel
Tel: 1-800-567000 call free in Israel; (972-50-8353722 after service hours until 20:00)
Fax: 972-3-6458759
E-mail: eastronics@eastronics.co.il
Service hours: Sun.~Thurs. 08:00 - 18:00
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/warcic.htm（第 9／9 页）2009-8-13 14:55:29
International Guarantee
Your International Guarantee
Dear Customer,
Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality
standards.
If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement
parts irrespective of the country where it is repaired during a period of 12 months from date of purchase. This international
Philips guarantee complements the existing national guarantee obligations to you of dealers and Philips in the country of
purchase and does not affect your statutory rights as a customer.
The Philips guarantee applies provided the product is handled properly for its intended use, in accordance with its
operating instructions and upon presentation of the original invoice or cash receipt, indicating the date of purchase,
dealer's name and model and production number of the product.
The Philips guarantee may not apply if:
● the documents have been altered in any way or made illegible;
● the model or production number on the product has been altered, deleted, removed or made illegible;
● repairs or product modifications and alterations have been executed by unauthorized service organizations or
persons;
● damage is caused by accidents including but not limited to lightning, water or fire, misuse or neglect.
Please note that the product is not defective under this guarantee in the case where modifications become necessary in
order for the product to comply with local or national technical standards which apply in countries for which the product
was not originally designed and/or manufactured. Therefore always check whether a product can be used in a specific
country.
In case your Philips product is not working correctly or is defective, please contact your Philips dealer. In the event you
require service whilst in another country a dealer address can be given to you by the Philips Consumer Help Desk in that
country, the telephone and fax number of which can be found in the relevant part of this booklet.
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions carefully before contacting
your dealer. If you have questions which your dealer cannot answer or any related question please contact the Philips
Consumer Information Centers or via:
Website: http://www.philips.com
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/war_intl.htm2009-8-13 14:55:33
United States Guarantee
Your Philips F1rst Choice Warranty(USA)
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and deliver high-quality
performance, ease of use and ease of installation. Should you encounter any difficulties while
installing or using this product, please contact Philips directly to benefit from your Philips F1rst
Choice Warranty. This three-year service warranty entitles you to a swap model on-site within 48
hours of your call being received within the first year of purchase. If you have any problems with
your monitor within the second or third year of purchase, we will repair it after it has been sent to
the service provider at your expense and returned to you within five working days, free of
charge.
LIMITED WARRANTY (Computer Monitor)
Click here to access the Warranty Registration Card.
Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange*
*Product will be exchanged with a new or renewed to original specifications unit within two
business days for the first year. This product must be shipped in at your expense for service during
years two and three.
WHO IS COVERED?
You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you
purchased the product is considered proof of purchase. Attach it to this owner's manual and keep both nearby.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product. For three years thereafter, all parts will be repaired or
replaced, and labor is free. After three years from the day of purchase, you pay for the replacement or repair of
all parts, and for all labor charges.
All parts, including repaired and replaced parts, are covered only for the original warranty period. When the warranty on
the original product expires, the warranty on all replaced and repaired products and parts also expires.
WHAT IS EXCLUDED?
Your warranty does not cover:
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/war_usa.htm（第 1／4 页）2009-8-13 14:55:39
United States Guarantee
● labor charges for installation or setup of the product, adjustment of customer controls on the product, and
installation or repair of antenna systems outside of the product.
● product repair and/or part replacement because of misuse, accident, unauthorized repair or other cause not
within the control of Philips Consumer Electronics.
● reception problems caused by signal conditions or cable or antenna systems outside the unit.
● a product that requires modification or adaptation to enable it to operate in any country other than the country for
which it was designed, manufactured, approved and/or authorized, or repair of products damaged by these
modifications.
● incidental or consequential damages resulting from the product. (Some states do not allow the exclusion of
incidental or consequential damages, so the above exclusion may not apply to you. This includes, but is not
limited to, prerecorded material, whether copyrighted or not copyrighted.)
● the model or production number on the product has been altered, deleted, removed or made illegible.
Where IS SERVICE AVAILABLE?
Warranty service is available in all countries where the product is officially distributed by Philips Consumer Electronics. In
countries where Philips Consumer Electronics does not distribute the product, the local Philips service organization will
attempt to provide service (although there may be a delay if the appropriate spare parts and technical manual(s) are not
readily available).
Where CAN I GET MORE INFORMATION?
For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A. customers only) or
(919) 573-7855.
Before Requesting Service...
Please check your owner's manual before requesting service. Adjustments of the controls discussed there may save you
a service call.
TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...
Contact the Philips Customer Care Center phone number listed below for product assistance and procedures for
servicing:
Philips Customer Care Center
(877) 835-1838 or (919) 573-7855
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties
of merchantability and fitness for a particular purpose, are limited in duration to the duration of this
express warranty. But, because some states do not allow limitations on how long an implied
warranty may last, this limitation may not apply to you.)
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/war_usa.htm（第 2／4 页）2009-8-13 14:55:39
United States Guarantee
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
(800) 479-6696
Three years free parts and three years free labor will be provided at Philips Canada depot or any one of its authorized
service centers.
(In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed or implied, including
any implied warranties of merchantability or fitness for a particular purpose. Philips is not liable under any circumstances
for any direct, indirect, special, incidental or consequential damages, howsoever incurred, even if notified of the possibility
of such damages.)
REMEMBER... Please record the model and serial numbers found on the product below.
MODEL # ________________________________________________
SERIAL # ________________________________________________
This warranty gives you specific legal rights. You may have other rights which vary from state/
province to state/province.
Before contacting Philips, please prepare the following details so we can solve your problem quickly.
● Philips type number
● Philips serial number
● Purchase date (copy of purchase may be required)
● PC environment Processor:
❍ CUP and Graphic card name and driver version
❍ Operating system
❍ Application being used
● Other cards installed
Having the following information available will also help speed up the process:
● Your proof of purchase indicating: date of purchase, dealer name, model and product serial number.
● The full address to which the swap model should be delivered.
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/war_usa.htm（第 3／4 页）2009-8-13 14:55:39
United States Guarantee
Just a phone call away
Philips’ customer help desks are located worldwide. Within the U.S. you can contact Philips customer care Monday-
Friday from 8:00 AM-9:00 PM Eastern Time (ET) and on Saturdays from 10:00 AM-5:00 PM ET hrs by using one of the
contact phone numbers.
For more information on this and more great Philips products visit our website at:
Website: http://www.philips.com
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/warranty/war_usa.htm（第 4／4 页）2009-8-13 14:55:39
Download and Print
•Installing your LCD monitor driver
•Download and Printing Instructions
Download and Print
Installing Your LCD monitor driver
System requirements:
● PC running Windows® 2000 , Windows® XP, Windows® Vista or later
● Find your driver ".inf/.icm/.cat" at : /PC/drivers/
Read the "Readme.txt" file before installing.
Add” refer to http://www.p4c.philips.com/ to download the latest version of monitor drivers.”
This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your hard disk, then
viewed and printed with Acrobat Reader or through your browser.
If you do not have Adobe® Acrobat Reader installed, click on the link to install the application. Adobe® Acrobat Reader for
PC / Adobe® Acrobat Reader for Apple Macintosh.
Download instructions:
To download the file:
1. Click-and-hold your mouse over the icon below. (Windows® 95/98/2000/Me/XP/Vista users right-click)
Download 190S1.pdf
2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to Disk'.
3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or 'source', choose 'source').
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/download/download.htm（第 1／2 页）2009-8-13 14:55:42
Download and Print
Printing instructions:
To print the manual:
With the manual file open, follow your printer's instructions and print the pages you need.
RETURN TO TOP OF THE PAGE
file:///F|/manual spec/813/spec/cd/Q70G900281311B 190S1/190S1 CD/lcd/manual/ENGLISH/download/download.htm（第 2／2 页）2009-8-13 14:55:42