Table of Contents
Philips 225B1CB/27 User Manual
Displayed below is the user manual for 225B1CB/27 by Philips which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
Safety and Troubleshooting Information
Safety Precautions and
Maintenance
FAQs
Troubleshooting
Regulatory Information
Safety and Troubleshooting Information
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than
those specified in this documentation may result in exposure to shock,
electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and using your computer monitor:
Operation:
● Keep the monitor out of direct sunlight and away from stoves or any other heat source.
● Remove any object that could fall into ventilation holes or prevent proper cooling of the
monitors electronics.
● Do not block the ventilation holes on the cabinet.
● When positioning the monitor, make sure the power plug and outlet are easily accessible.
● If turning off the monitor by detaching the power cable or DC power cord, wait for 6
seconds before attaching the power cable or DC power cord for normal operation.
● Please use approved power cord provided by Philips all the time. If your power cord is
missing, please contact with your local service center. (Please refer to Customer Care
Consumer Information Center)
● Do not subject the LCD monitor to severe vibration or high impact conditions during
operation.
● Do not knock or drop the monitor during operation or transportation.
Maintenance:
● To protect your display from possible damage, do not put excessive pressure on the LCD
panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by
placing your hand or fingers on the LCD panel.
● Unplug the monitor if you are not going to use it for an extensive period of time.
● Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be
wiped with a dry cloth when the power is off. However, never use organic solvent, such
as, alcohol, or ammonia-based liquids to clean your monitor.
● To avoid the risk of shock or permanent damage to the set, do not expose the monitor to
dust, rain, water, or excessive moisture environment.
● If your monitor gets wet, wipe it with dry cloth as soon as possible.
● If foreign substance or water gets in your monitor, please turn the power off immediately
and disconnect the power cord. Then, remove the foreign substance or water, and send
it to the maintenance center.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/safety.htm 第 1 頁 / 共 2 [98-07-01 15:08]
Safety and Troubleshooting Information
● Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or
extreme cold.
● In order to maintain the best performance of your monitor and use it for a longer lifetime,
please use the monitor in a location that falls within the following temperature and
humidity ranges.
❍ Temperature: 0-40°C 32-95°F
❍ Humidity: 20-80% RH
● IMPORTANT: Always activate a moving screen saver program when you leave your
monitor unattended. Always activate a periodic screen refresh application if your LCD
monitor will display unchanging static content. Uninterrupted display of still or static
images over an extended period may cause “burn in”, also known as “after-imaging” or
“ghost imaging”, on your screen. "Burn-in", "after-imaging", or "ghost imaging" is a well-
known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-
imaging” or “ghost imaging” will disappear gradually over a period of time after the power
has been switched off.
WARNING: Severe” burn-in” or “after-image” or “ghost image” symptoms will not
disappear and cannot be repaired. The damage mentioned above is not covered under
your warranty.
Service:
● The casing cover should be opened only by qualified service personnel.
● If there is any need for any document for repair or integration, please contact with your
local service center. (please refer to the chapter of "Consumer Information Center")
● For transportation information, please refer to "Physical Specifications".
● Do not leave your monitor in a car/trunk under direct sun light.
Consult a service technician if the monitor does not operate normally, or you are
not sure what procedure to take when the operating instructions given in this
manual have been followed.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/safety.htm 第 2 頁 / 共 2 [98-07-01 15:08]
FAQs (Frequently Asked Questions)
Safety and Troubleshooting
General FAQs
Compatibility with Other
Peripherals
LCD Panel Technology
Ergonomics, Ecology and
Safety Standards
Troubleshooting
Regulatory Information
FAQs (Frequently Asked Questions)
General FAQs
Q1: When I install my monitor what should I do if the screen shows 'Cannot display this
video mode'?
A: Recommended resolution for Philips 22": 1680x1050 @60Hz.
1. Unplug all cables, then connect your PC to the monitor that you used
previously.
2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel
Window, select the Display icon. Inside the Display Control Panel, select the
'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the
slidebar to 1680x1050 pixels (22").
3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.
4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at
1680x1050@60Hz (22").
5. Shut down your computer, disconnect your old monitor and reconnect your
Philips LCD monitor.
6. Turn on your monitor and then turn on your PC.
Q2: What does the recommended refresh rate for LCD monitor?
A:Recommended refresh rate in LCD monitors is 60Hz, In case of any disturbance
on screen, you can set it up to 75Hz to see if that removes the disturbance.
Q3: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .
icm)?
A: These are the driver files for your monitor. Follow the instructions in your user
manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .
icm files) or a driver disk when you first install your monitor. Follow the instructions to
insert the ( companion CD-ROM) included in this package. Monitor drivers (.inf and .
icm files) will be installed automatically.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/saf_faq.htm 第 1 頁 / 共 5 [98-07-01 15:09]
FAQs (Frequently Asked Questions)
Q4: How do I adjust the resolution?
A: Your video card/graphic driver and monitor together determine the available
resolutions. You can select the desired resolution under Windows® Control Panel
with the "Display properties".
Q5: What if I get lost when I am making monitor adjustments?
A: Simply press the OK button, then select 'Reset' to recall all of the original factory
settings.
Q6: Will the LCD screen be resistant to scratches?
A: In general it is recommended that the panel surface is not subjected to excessive
shocks and is protected from sharp or blunt objects. When handling the monitor,
make sure that there is no pressure or force applied to the panel surface side. This
may affect your warranty conditions.
Q7: How should I clean the LCD surface?
A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use
isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone,
hexane, etc.
Q8:Can I change the color setting of my monitor?
A:Yes, you can change your color setting through OSD control as the following
procedures,
1. Press "OK" to show the OSD (On Screen Display) menu
2. Press "Down Arrow" to select the option "Color" then press "OK" to enter color
setting, there are three settings as below.
a. Color Temperature; The six settings are 5000K, 6500K, 7500K, 8200K,
9300K and 11500K. With settings in the 5000K range the panel appears
‘warm,' with a red-white color tone, while a 11500K temperature yields ‘cool,
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/saf_faq.htm 第 2 頁 / 共 5 [98-07-01 15:09]
FAQs (Frequently Asked Questions)
blue-white toning."
b. sRGB; this is a standard setting for ensuring correct exchange of colors
between different device (e.g. digital cameras, monitors, printers, scanners,
etc)
c. User Define; the user can choose his/her preference color setting by
adjusting red, green blue color.
*A measurement of the color of light radiated by an object while it is being heated.
This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower
Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are
blue. Neutral temperature is white, at 6504K.
Q9: Can the Philips LCD Monitor be mounted on the wall?
A: Yes. Philips LCD monitors have this optional feature. For standard VESA mount
holes on the rear cover allows the user to mount the Philips monitor on most of the
VESA standard arms or accessories. We recommend to contact your Philips sales
representative for more information.
RETURN TO TOP OF THE PAGE
Compatibility with other Peripherals
Q10: Can I connect my LCD monitor to any PC, workstation or Mac?
A: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and
workstations. You may need a cable adapter to connect the monitor to your Mac
system. Please contact your Philips sales representative for more information.
Q11: Are Philips LCD monitors Plug-and-Play?
A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000, XP,
Vista and Linux.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/saf_faq.htm 第 3 頁 / 共 5 [98-07-01 15:09]
FAQs (Frequently Asked Questions)
LCD Panel Technology
Q12: What kind of wide-angle technology is available?
A: Currently, the IPS type panels offer the best Contrast Ratio, compared to MVA, or
PVA technologies. TN panels have improved over the years, but still cannot match
the Contrast Ratio offered by IPS panel.
RETURN TO TOP OF THE PAGE
Ergonomics, Ecology and Safety Standards
Q13: What is Image Sticking, or Image Burn-in, or After Image, or Ghost Image in LCD
panels?
A: Uninterrupted display of still or static images over an extended period may cause
"burn in", also known as "after-imaging" or "ghost imaging", on your screen. "Burn-in",
"after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel
technology. In most cases, the "burned in" or "atter-imaging" or "ghost imaging" will
disappear gradually over a period of time after the power has been switched off.
Always activate a moving screen saver program when you leave your monitor
unattended.
Always activate a periodic screen refresh application if your LCD monitor will display
unchanging static content.
WARNING: Severe"burn-in" or "after-image" or "ghost image" symptoms will not
disappear and cannot be repaired. The damage mentioned above is not covered
under your warranty.
Q14: Why is my Display not showing sharp text, and is displaying jagged characters?
A: Your LCD monitor works best at its native resolution of 1680x1050@60Hz. For
best display please use this resolution.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/saf_faq.htm 第 4 頁 / 共 5 [98-07-01 15:09]
FAQs (Frequently Asked Questions)
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/saf_faq.htm 第 5 頁 / 共 5 [98-07-01 15:09]
Troubleshooting
Safety and
Troubleshooting
FAQs
Common Problems
Imaging Problems
Regulatory Information
Troubleshooting
This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these
solutions, contact Philips customer service representative.
Common Problems
Having this problem Check these items
No Picture
(Power LED not lit)
● Make sure the power cord is plugged into the power outlet
and into the back of the monitor.
● First, ensure that the power button on the front of the monitor
is in the OFF position, then press it to the ON position.
No Picture
(Power LED is white blinking)
● Make sure the computer is turned on.
● Make sure the signal cable is properly connected to your
computer.
● make sure the monitor cable has no bent pins on the connect
side. If yes, repair or replace the cable.
● The Energy Saving feature may be activated
Screen says
● Make sure the monitor cable is properly connected to your
computer. (Also refer to the Quick Set-Up Guide).
● Check to see if the monitor cable has bent pins.
● Make sure the computer is turned on.
AUTO button doesn't function in VGA
mode
● The auto function is applicable only in VGA-Analog mode. If
the result is not satisfactory, you can do manual adjustments
via the OSD menu. Note that the Auto Function is not
applicable in DVI-Digital mode as it is not necessary.
Imaging Problems
Image is not centered
● Press the Auto button.
● Adjust the image position using the Phase/Clock of Setup in
OSD Main Controls.
saf_troub.htm 第 1 頁 / 共 3 [98-07-01 15:09]file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/
Troubleshooting
Image vibrates on the screen
● Check that the signal cable is properly securely connected to
the graphics board or PC.
Vertical flicker appears
● Press the Auto button.
● Eliminate the vertical bars using the Phase/Clock of Setup in
OSD Main Controls.
Horizontal flicker appears
● Press the Auto button.
● Eliminate the vertical bars using the Phase/Clock of Setup in
OSD Main Controls.
image appears blurred, indistinct or too
dark
● Adjust the contrast and brightness on On-Screen Display.
An "after-image", "burn-in" or "ghost
image" remains after the power has
been turned off.
● Uninterrupted display of still or static images over an
extended period may cause " burn in", also known as "after-
imaging " or "ghost imaging", on your screen. "Burn-in", "after-
imaging", or "ghost imaging" is a well-known phenomenon in
LCD panel technology. In most cases, the "burned in" or
"after-imaging" or "ghost imaging" will disappear gradually
over a period of time after the power has been switched off.
● Always activate a moving screen saver program when you
leave your monitor unattended.
● Always activate a periodic screen refresh application if your
LCD monitor will display unchanging static content.
Image appears distorted. Text is fuzzy
or blurred.
● Set the PC’s display resolution to the same mode as
monitor’s recommended screen native resolution.
Green, red, blue, dark, and white dots
appears on the screen
● The remaining dots are normal characteristic of the liquid
crystal used in todays technology, Pls refer the pixel policy for
more detail.
saf_troub.htm 第 2 頁 / 共 3 [98-07-01 15:09]file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/
Troubleshooting
The "power on" light is too strong to
disturb me.
● You can adjust “power on” light using the power LED of Setup
in OSD main Controls.
For further assistance, refer to the Consumer Information Centers list and contact Philips customer service
representative.
RETURN TO TOP OF THE PAGE
saf_troub.htm 第 3 頁 / 共 3 [98-07-01 15:09]file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/safety/
Regulatory Information
TCO'03 Information
Recycling Information for Customers
Waste Electrical and Electronic
Equipment-WEEE
CE Declaration of Conformity
Energy Star Declaration
Federal Communications
Commission (FCC) Notice (U.S.
Only)
FCC Declaration of Conformity
Commission Federale de la
Communication (FCC Declaration)
EN 55022 Compliance (Czech
Republic Only)
Polish Center for Testing and
Certification Notice
North Europe (Nordic Countries)
Information
BSMI Notice (Taiwan Only)
Ergonomie Hinweis (nur
Deutschland)
Philips End-of-Life Disposal
China RoHS
Lead-free Product
Troubleshooting
Frequently Asked Questions (FAQs)
Regulatory Information
Available for selective models
TCO'03 Information
Congratulations!
The display you have just purchased carries the TCO'03 Displays label. This
means that your display is designed, manufactured and tested according to some
of the strictest quality and environmental requirements in the world. This makes for
a high performance product, designed with the user in focus that also minimizes the
impact on our natural environment.
Some of the features of the TCO'03 Display requirements.
Ergonomics
● Good visual ergonomics and image quality in order to improve the working environment for the user and
to reduce sight and strain problems. Important parameters are luminance, contrast, resolution,
reflectance, colour rendition and image stability.
Energy
● Energy-saving mode after a certain time-beneficial both for the user and the environment
● Electrical safety
Emissions
● Electromagnetic fields
● Noise emissions
Ecology
● The product must be prepared for recycling and the manufacturer must have a certified environmental
management system such as EMAS or ISO 14 000
● Restrictions on
❍ chlorinated and brominated flame retardants and polymers
❍ heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO Development in co-operation with
scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has
been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling
system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world.
For more information, please visit
www.tcodevelopment.com
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...mat/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 1 頁 / 共 10 [98-07-09 17:43]
Regulatory Information
Recycling Information for Customers
There is currently a system of recycling up and running in the European countries, such as The Netherlands,
Belgium, Norway, Sweden and Denmark.
In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA) to
follow the IT product recycling management process, detail can be found in web site www.epa.gov.tw
The monitor contains parts that could cause damage to the nature environment. Therefore, it is vital that the monitor is
recycled at the end of its life cycle.
For help and service, please contact Consumers Information Center or F1rst Choice Contact Information
Center in each country.
RETURN TO TOP OF THE PAGE
Waste Electrical and Electronic Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive
2002/96/EC governing used electrical and electronic appliances, this product may not be disposed of with
normal household waste. You are responsible for disposal of this equipment through a designated waste
electrical and electronic equipment collection. To determine the locations for dropping off such waste electrical
and electronic, contact your local government office, the waste disposal organization that serves your
household or the store at which you purchased the product.
Attention users in United States:
Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State
and Federal laws. For the disposal or recyciing information, contact www.mygreenelectronics.com or www.eiae.
org.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...mat/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 2 頁 / 共 10 [98-07-09 17:43]
Regulatory Information
EPEAT
“The EPEAT (Electronic Product Environmental Assessment Tool) program evaluates computer desktops,
laptops, and monitors based on 51 environmental criteria developed through an extensive stakeholder
consensus process supported by US EPA.
EPEAT system helps purchasers in the public and private sectors evaluate, compare and select desktop
computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and
consistent set of performance criteria for the design of products, and provides an opportunity for manufacturers
to secure market recognition for efforts to reduce the environmental impact of its products.”
Benefits of EPEAT
Reduce use of primary materials
Reduce use of toxic materials
Avoid the disposal of hazardous waste EPEAT’S requirement that all registered products meet ENERGY
STAR’s energy efficiency specifications, means that these products will consume less energy throughout their
life.
RETURN TO TOP OF THE PAGE
ROHS is a European Directive aiming to control the use of certain hazardous substances in the production of
new electrical and electronic equipment. Philips has completely eliminated four of six RoHS-banned
substances form its products by 1998-eight full years before compliance was required and has lowered usage
of the remaining substances significantly below the mandated levels.
RETURN TO TOP OF THE PAGE
CE Declaration of Conformity
This product is in conformity with the following standards
- EN60950-1:2001 (Safety requirement of Information Technology Equipment)
- EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment)
- EN55024:1998 (Immunity requirement of Information Technology Equipment)
- EN61000-3-2:2006 (Limits for Harmonic Current Emission)
- EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable
- 2006/95/EC (Low Voltage Directive)
- 2004/108/EC (EMC Directive)
and is produced by a manufacturing organization on ISO9000 level.
The product also comply with the following standards
- ISO13406-2 (Ergonomic requirement for Flat Panel Display)
- GS EK1-2000 (GS specification)
- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)
- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)
- TCO'03, TCO Displays 5.0 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and
Emission, TCO: Swedish Confederation of Professional Employees) for TCO versions
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...mat/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 3 頁 / 共 10 [98-07-09 17:43]
Regulatory Information
Energy Star Declaration
This monitor is equipped with a function for saving energy which supports the VESA Display
Power Management Signaling (DPMS) standard. This means that the monitor must be
connected to a computer which supports VESA DPMS. Time settings are adjusted from the
system unit by software.
VESA State LED Indicator Power Consumption
Normal operation ON (Active) White < 20 W (typ.)
Power Saving
Alternative 2
One step Sleep White Blinking < 0.5 W (typ.)
Switch Off Off < 0.5 W (typ.)
As an ENERGY STAR® Partner, we have determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
We recommend you switch off the monitor when it is not in use for a long time.
RETURN TO TOP OF THE PAGE
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...mat/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 4 頁 / 共 10 [98-07-09 17:43]
Regulatory Information
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer
device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive
moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
RETURN TO TOP OF THE PAGE
FCC Declaration of Conformity
Declaration of Conformity for Products Marked with FCC Logo,
United States Only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
RETURN TO TOP OF THE PAGE
Commission Federale de la Communication (FCC Declaration)
Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de
class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon
à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une
installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences
qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer
des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir
l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la
cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce
qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur
pourrait essayer de corriger la situation en prenant les mesures suivantes:
● Réorienter ou déplacer l'antenne de réception.
● Augmenter la distance entre l'équipement et le récepteur.
● Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.
● Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de
conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...mat/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 5 頁 / 共 10 [98-07-09 17:43]
Regulatory Information
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT
SUR LE MATERIEL BROUILLEUR DU CANADA.
RETURN TO TOP OF THE PAGE
EN 55022 Compliance (Czech Republic Only)
RETURN TO TOP OF THE PAGE
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All
equipment that works together (computer, monitor, printer, and so on) should have the same power supply
source.
The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device
in the form of a fuse with a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply
socket, which should be located near the equipment and easily accessible.
A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of
standards PN-93/T-42107 and PN-89/E-06251.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...mat/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 6 頁 / 共 10 [98-07-09 17:43]
Regulatory Information
RETURN TO TOP OF THE PAGE
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR
DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT
ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI
IRROTTAA PISTORASIASTA.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...mat/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 7 頁 / 共 10 [98-07-09 17:43]
Regulatory Information
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR
STØMTILFØRSEL ER LETTE Å NÅ.
RETURN TO TOP OF THE PAGE
BSMI Notice (Taiwan Only)
RETURN TO TOP OF THE PAGE
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch
Röntgenstrahlen" festgelegten Vorschriften.
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme
hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der
Röntgenverordnung erfüllt sind.
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß
1. Reparaturen nur durch Fachpersonal durchgeführt werden.
2. nur original-Ersatzteile verwendet werden.
3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem
Zeichenkontrast wären die Folge).
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
RETURN TO TOP OF THE PAGE
End-of-Life Disposal
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...mat/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 8 頁 / 共 10 [98-07-09 17:43]
Regulatory Information
Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your
product to increase the amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old monitor from your sales
representative.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations.
For additional information on recycling contact www.eia.org (Consumer Education Initiative)
RETURN TO TOP OF THE PAGE
China RoHS
The People's Republic of China released a regulation called "Management Methods for Controlling Pollution by
Electronic Information Products" or commonly referred to as China RoHS. All products including CRT and LCD
monitor which are produced and sold for China market have to meet China RoHS request.
环保使用期限
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...mat/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 9 頁 / 共 10 [98-07-09 17:43]
Regulatory Information
此标识指期限(十年),电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外泄或突
变, 电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身、 财产造成严重损害的期
限．
RETURN TO TOP OF THE PAGE
Lead-free Product
Lead free display promotes environmentally sound recovery and disposal of waste from
electrical and electronic equipment. Toxic substances like Lead has been eliminated and
compliance with European community’s stringent RoHs directive mandating restrictions on
hazardous substances in electrical and electronic equipment have been adhered to in order to
make Philips monitors safe to use throughout its life cycle.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-E...at/CD-Contents/lcd/manual/ENGLISH/225B1/SAFETY/REGS/REGULAT.HTM 第 10 頁 / 共 10 [98-07-09 17:43]
About This Manual
About This Guide
Notational Descriptions
About This Manual
About This Guide
This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It
describes the LCD monitor's features, setup, operation and other important information. Its
contents are identical to the information in our printed version.
It includes the following sections:
● Safety and Troubleshooting Information provides tips and solutions for common problems
as well as other related information you may need.
● About This Electronic User's Manual gives an overview of information included, along with
notation icon descriptions and other documentation for your reference.
● Product Information gives an overview of the monitor's features as well as the technical
specifications for this monitor.
● Installing Your Monitor describes the initial setup process and gives an overview of how to
use the monitor.
● On-Screen Display provides information on adjusting the settings on your monitor.
● Customer Care and Warranty contains a list of worldwide Philips Consumer Information
Centers along with help desk phone numbers and information on the warranty applicable
to your product.
● Glossary defines technical terms.
● Download and Print Option transfers this entire manual to your hard drive for easy
reference.
RETURN TO TOP OF THE PAGE
Notational Descriptions
The following subsections describe notational conventions used in this document.
Notes, Cautions and Warnings
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/about/about.htm 第 1 頁 / 共 2 [98-07-01 15:09]
About This Manual
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic
type. These blocks contain notes, cautions or warnings. They are used as follows:
NOTE: This icon indicates important information and tips that help you make
better use of your computer system.
CAUTION: This icon indicates information that tells you how to avoid either
potential damage to hardware or loss of data.
WARNING: This icon indicates the potential for bodily harm and tells you how
to avoid the problem.
Some warnings may appear in alternate formats and may not be accompanied by an icon. In
such cases, the specific presentation of the warning is mandated by the relevant regulatory
authority.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/about/about.htm 第 2 頁 / 共 2 [98-07-01 15:09]
Product Information
Your LCD Monitor
PowerSensor
Smartimage
SmartContrast
SmartSaturate
SmartSharpness
Technical Specifications
Resolution & Preset Modes
Philips Pixel Defect Policy
Automatic Power Saving
Product Views
Physical Function
SmartControl II
Product Information
Your LCD monitor
Congratulations on your purchase and welcome to Philips. To fully benefit from the support that Philips offers, register
your product at. www.philips.com/welcome
PowerSensor
What is PowerSensor?
PowerSensor is a unique environmentally friendly technology from Philips which enables user to save upto 70% of
power consumption. It is very user friendly and requires no software installation in order to operate. It works by
default thereby starting to save power and money straight out of the box.
User present in front User not present
Power consumption as illustrated above is for reference purpose only.
How does it work?
❍ PowerSensor works on principle of transmission and reception of harmless “infrared” signals in order to detect user-presence.
❍ When the user is in front of the monitor the monitor operates normally, at the predetermined settings that the user has set- i.e.
Brightness, contrast, color, etc
❍ Assuming that the monitor was set to 100% of brightness for example, when the user leaves his seat and is no longer in front of the
monitor, the monitor dims down to 30% of the brightness level
What are the Benefits?
❍ Reduction of brightness results in about 50% to 70% power savings
❍ Reduction in Total Cost of Ownership (TCO) to the company
❍ “Green” performance, Environment friendly operations
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 1 頁 / 共 12 [98-07-10 12:01]
Product Information
❍ Increase in lifetime of monitor, results in lower TCO
PowerSensor settings
Default settings
At its default setting, Setting 3, PowerSensor is designed to detect the presence of a monitor user located between 30
and 100 cm (12 and 40 inches) from the display and within five degrees left or right of the monitor.
Custom settings
When a user chooses a position outside the perimeters listed above, choose a higher strength signal for optimal
detection efficiency: The higher the setting, the stronger the detection signal. For maximum PowerSensor efficiency,
please position yourself directly in front of your monitor.
❍ If you choose to position yourself more than 100 cm or 40 inches from the monitor use the maximum detection signal for distances
up to 120cm or 47 inches.
❍ Since dark colored clothing tends to absorb infrared signals even when the user is within 100 cm or 40 inches of the display, step
up signal strength when wearing black or other dark garb.
❍ You can return to the default mode at any time a narrower detection range is desired.
How to adjust settings
If PowerSensor is not operating correctly inside or outside the default range, here’s how to fine-tune detection:
❍ Press the PowerSensor hot key
❍ You will find the default position ‘3’ on the adjustment bar.
❍ Adjust the PowerSensor detection adjustment to Setting 4 and press OK.
❍ Test the new setup to see if PowerSensor properly detect you in your current position.
Note:
A manually selected PowerSensor mode will remain operational unless and until it is readjusted or the default mode is recalled.
If PowerSensor is excessively sensitive to nearby motion, experiment with a lower signal strength.
Hot key Sensor distance
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 2 頁 / 共 12 [98-07-10 12:01]
Product Information
SmartImage
What is it?
SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness,
contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching
a video, Philips SmartImage delivers great optimized LCD display performance.
Why do I need it?
You want a LCD display that delivers optimized display all your favorite types of content, SmartImage software
dynamically adjust brightness, contrast, color and sharpness in real time to enhance your LCD viewing experience.
How does it work?
SmartImage is an exclusive, leading edge Philips technology that analyzes the content displayed on your screen. Based on
a scenario you select, SmartImage dynamically enhances the contrast, color saturation and sharpness of images and
videos for ultimate display performance - all in real time with the press on a single button.
How to enable SmartImage?
1. Press to launch the SmartImage on screen display;
2. Keep press to toggle between Office Work, Image Viewing, Entertainment, Economy, and Off;
3. The SmartImage on screen display will remain on screen for 5 seconds or you can also press”OK” to make
confirmation.
4. When SmartImage is enabled, the sRGB scheme is disabled automatically. To use sRGB you need to
disable SmartImage with the button at the front bezel of your monitor.
Except using key to scroll down, you can also press buttons to choose and press “OK” to confirm selection
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 3 頁 / 共 12 [98-07-10 12:01]
Product Information
and close the SmartImage OSD.There are five modes to be selected: Office Work, Image Viewing, Entertainment,
Economy, and Off.
There are five modes to be selected: Office Work, Image Viewing, Entertainment, Economy, and Off.
1.
Office Work: Enhances text and dampens brightness to increase readability and reduce eye strain. This mode
significantly enhances readability and productivity when you're working with spreadsheets, PDF files, scanned articles or
other general office applications.
2.
Image Viewing: This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos
and other images with outstanding clarity in vibrant colors - all without artifacts and faded colors.
3.
Entertainment: Ramped up luminance, deepened color saturation, dynamic contrast and razor sharpness displays every
details in darker areas of your videos without color washout in brighter areas maintaining a dynamic natural values for the
ultimate video display.
4.
Economy: Under this profile, brightness, contrast are adjusted and backlighting fine-tuned for just right display of
everyday office applications and lower power consumption.
5.
Off: No optimization by SmartImage.
RETURN TO TOP OF THE PAGE
SmartContrast
What is it?
Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor's contrast
ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter images
or dimming backlighting for clear display of images on dark backgrounds.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 4 頁 / 共 12 [98-07-10 12:01]
Product Information
Why do I need it?
You want the very best visual clarity and viewing comfort for every type of content. SmartContrast dynamically
controls contrast and adjusts backlighting for clear, crisp, bright gaming and video images or displays clear, readable text
for office work. By reducing your monitor's power consumption, you save on energy costs and extend the lifetime of
your monitor.
How does it work?
When you active SmartContrast which will analysis the content you are displaying in real time to adjust colors and
control backlight intensity. This function can obviously enhance contrast in dynamic for more entertainment fun when
viewing videos or playing games.
RETURN TO TOP OF THE PAGE
SmartSaturate
What is it?
Smart technology that controls color saturation - the degree to which one on screen color is diluted by neighboring colors -
to deliver rich and vibrant images for more entertainment fun when you are viewing videos.
Why do I need it?
You want rich, vibrant images for more entertainment fun when viewing photos or videos.
How does it work?
SmartSaturate dynamically controls color saturation - the degree to which on-screen color is diluted by neighboring colors -
to deliver rich, vibrant display for more entertainment fun when you are viewing images or videos in your
display's Entertainment mode and is turned off for top quality display of office application and in the Economy mode to
reduce power consumption.
RETURN TO TOP OF THE PAGE
SmartSharpness
What is it?
Smart technology that enhances sharpness when you need it for ultimate display performance and more entertainment
fun when you are viewing videos or photos.
Why do I need it?
You want the ultimate in sharpness for more entertainment fun when viewing photos or videos.
How does it work?
Smart technology enhances sharpness when you need it for ultimate display performance and more entertainment fun
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 5 頁 / 共 12 [98-07-10 12:01]
Product Information
when you are viewing videos or photos in the Entertainment mode and is turned off for top quality display of
office applications and in the Economy mode to reduce power consumptions.
RETURN TO TOP OF THE PAGE
Technical Specifications*
Picture/Display
LCD panel type TFT-LCD
Panel size 22'' W
Aspect ratio 16:10
Pixel Pitch 0.282 x 0.282 mm
Brightness 250 cd/m²
SmartContrast 25000:1
Contrast ratio (typ.) 1000:1
Response time (typical) 5 ms
Optimum Resolution 1680 x 1050 @ 60Hz
Viewing angle 176° (H) / 170° (V) @ C/R > 5
Picture Enhancement Smartimage
Display colors 16.7 M
Vertical refresh rate 56Hz -76Hz
Horizontal Frequency 30kHz - 80kHz
sRGB YES
Connectivity
Signal input DVI-D (digital, HDCP), VGA (Analog)
USB USB 2.0 x 1
Input Signal Separate Sync, Sync on Green
Audio In/Out Stereo Audio
Convenience
Built-in Audio 1.5 W x 2
User Convenience Smartimage, Auto (Back), Input (Down), Brightness (UP) Menu (OK),
Power On/Off
OSD Languages English, French, German, Italian, Russian, Spanish, Simplified Chinese,
Portuguese
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 6 頁 / 共 12 [98-07-10 12:01]
Product Information
Other convenience VESA mount ( 100 x 100mm), Kensington lock
Plug & Play Compatibility DDC/CI, sRGB, Windows 98/2000/XP/Vista, Mac OS X
Stand
Tilt -5/+20
Height adjustment 130mm (225P1), 70mm (225B1)
Swivel -65/+65 (225P1), -45/+45 (225B1)
Power
On mode < 24 W (typ.), < 30 W (max)
On mode (ECO mode) (typical) < 17.5 W
Energy Consumption
(EnergyStar 5.0 test method)
AC Input Voltage at
100VAC +/-5VAC,
50Hz +/- 3Hz
AC Input Voltage at
115VAC +/-5VAC,
60Hz +/- 3Hz
AC Input Voltage at
230VAC +/-5VAC, 50Hz
+/ -3Hz
Normal Operation (typcial) 20 W 20 W 20 W
Sleep 0.5 W (typ.) 0.5 W (typ.) 0.5 W (typ.)
Off 0.5 W 0.5 W 0.5 W
Heat Dissipation*
AC Input Voltage at
100VAC +/-5VAC,
50Hz +/ -3Hz
AC Input Voltage at
115VAC +/-5VAC,
60Hz +/ -3Hz
AC Input Voltage at
230VAC +/-5VAC, 50Hz
+/ -3Hz
Normal Operation 102.4BTU/hr 102.4BTU/hr 102.4BTU/hr
Sleep 2.73BTU/hr 2.73BTU/hr 2.73BTU/hr
Off 1.7BTU/hr 1.7BTU/hr 1.7BTU/hr
Power LED indicator On mode: White, Standby/Sleep mode: White (blinking)
Power Supply Build-in, 100-240VAC, 50/60Hz
Dimension
Product with stand (WxHxD) 502 x 589 x 220mm (225P1), 502 x 446 x 228mm (225B1)
Product without stand (WxHxD) 502 x 346 x 58mm
Box dimension (WxHxD) 658 x 410 x 272mm (225P1), 562 x 480 x 168mm (225B1)
Weight
Product with stand 6.4kg (225P1), 5.2kg (225B1)
Product without stand 4.1kg
Product with packaging 7.6kg (225P1), 6.9kg (225B1)
Operating Condition
Temperature range (operation) 0° C to 40 ° C
Temperature range (operation) -20° C to 60° C
Relative humidity 20% to 80%
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 7 頁 / 共 12 [98-07-10 12:01]
Product Information
Altitude Non-operation: + 12,000 ft ( 3,658 m)
operation: + 40,000 ft ( 12,192 m),
MTBF 50000 hrs
Environmental
ROHS YES
EPEAT sliver
EnergyStar 5.0
Packaging 100% recyclable
Compliance and standards
Regulatory Approvals CE Mark, Energy Star 5.0, FCC Class B, SEMKO, TCO 03, TÜV/GS, TÜV
Ergo, UL/cUL
Cabinet
Color Black/Sliver, Black/Black
Finish Texture
* This data is subject to change without notice.
RETURN TO TOP OF THE PAGE
Resolution & Preset Modes
A. Maximum Resolution
- For 225P1/225B1
1680 x 1050 at 60 Hz (analog input)
1680 x 1050 at 60 Hz (digital input)
B. Recommended Resolution
- For 225P1/225B1
1680 x 1050 at 60 Hz (digital input)
18 factory preset modes:
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 8 頁 / 共 12 [98-07-10 12:01]
Product Information
H. freq (kHz) Resolution V. freq (Hz)
31.469 640*350 70.086
31.469 720*400 70.087
31.469 640*480 59.940
35.000 640*480 67.000
37.500 640*480 75.000
35.156 800*600 56.250
37.879 800*600 60.317
46.875 800*600 75.000
48.363 1024*768 60.004
60.023 1024*768 75.029
63.981 1280*1024 60.020
79.976 1280*1024 75.025
55.469 1440*900 59.901
55.935 1440*900 59.887
70.635 1440*900 74.984
66.587 1920*1080 60.000 (reduce blinking)
65.290 1680*1050 60.000
64.674 1680*1050 60.000
RETURN TO TOP OF THE PAGE
Automatic Power Saving
If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce
its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor
will 'wake up' automatically. The following table shows the power consumption and signaling of this automatic power
saving feature:
Power Management Definition
VESA Mode Video H-sync V-sync Power Used LED
color
Active ON Yes Yes
< 24 W (typ.)
< 30 W (max.) White
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 9 頁 / 共 12 [98-07-10 12:01]
Product Information
Sleep OFF No No < 0.5 W (typ.) White
(Blinking)
Switch Off OFF - - < 0.5 W (typ.) Off
This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, we have determined that
this product meets the ENERGY STAR® guidelines for energy efficiency.
* This data is subject to change without notice.
The native resolution of the monitor is 1680 x 1050, By default, your monitor has 100% (max.) 50% contrast, and 6500K
color temperature, with full white pattern, without audio/USB.
RETURN TO TOP OF THE PAGE
Product Views
Follow the links to see various views of the monitor and its components.
Front View Product Description
RETURN TO TOP OF THE PAGE
Physical Function
Tilt
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 10 頁 / 共 12 [98-07-10 12:01]
Product Information
Swivel
Height adjustment
Pivot (225P1)
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-ED...-format/CD-Contents/lcd/manual/ENGLISH/225B1/PRODUCT/PRODUCT.HTM 第 11 頁 / 共 12 [98-07-10 12:01]
Philips Pixel Defect Policy
Product Features
Technical Specifications
Resolution & Preset Modes
Automatic Power Saving
Physical Specification
Pin Assignment
Product Views
Philips Pixel Defect Policy
Philips' Flat Panel Monitors Pixel Defect Policy
Philips strives to deliver the highest quality products. We use some of the industry's most advanced
manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on
the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can
guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with
an unacceptable number of defects will be repaired or replaced under warranty. This notice explains
the different types of pixel defects and defines acceptable defect levels for each type. In order to
qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel
must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a 19"
XGA monitor may be defective. Furthermore, Philips sets even higher quality standards for certain
types or combinations of pixel defects that are more noticeable than others. This policy is valid
worldwide.
Pixels and Sub pixels
A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and
blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub
pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together
appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of
other colors.
Types of Pixel Defects
Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel
defects and several types of sub pixel defects within each category.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/pixel.htm 第 1 頁 / 共 4 [98-07-01 15:10]
Philips Pixel Defect Policy
Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is,
a bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern.
There are the types of bright dot defects:
One lit red, green or blue sub
pixel
Two adjacent lit sub pixels:
- Red + Blue = Purple
- Red + Green = Yellow
- Green + Blue = Cyan (Light Blue)
Three adjacent lit sub pixels
(one white pixel)
A red or blue bright dot must be more than 50 percent brighter than neighboring dots
while a green bright dot is 30 percent brighter than neighboring dots.
Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That
is, a dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern.
These are the types of black dot defects:
One dark sub pixel Two or three adjacent dark sub pixels
Proximity of Pixel Defects
Because pixel and sub pixels defects of the same type that are near to one another may be more
noticeable, Philips also specifies tolerances for the proximity of pixel defects.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/pixel.htm 第 2 頁 / 共 4 [98-07-01 15:10]
Philips Pixel Defect Policy
Pixel Defect Tolerances
In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT
LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the
tolerances listed in the following tables.
BRIGHT DOT DEFECTS ACCEPTABLE LEVEL
MODEL 225P1/225B1
1 lit subpixel 3
2 adjacent lit subpixels 1
3 adjacent lit subpixels (one white pixel) 0
Distance between two bright dot defects* >15mm
Total bright dot defects of all types 3
BLACK DOT DEFECTS ACCEPTABLE LEVEL
MODEL 225P1/225B1
1 dark subpixel 5 or fewer
2 adjacent dark subpixels 2 or fewer
3 adjacent dark subpixels 0
Distance between two black dot defects* >15mm
Total black dot defects of all types 5 or fewer
TOTAL DOT DEFECTS ACCEPTABLE LEVEL
MODEL 225P1/225B1
Total bright or black dot defects of all types 5 or fewer
Note:
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/pixel.htm 第 3 頁 / 共 4 [98-07-01 15:10]
SmartControl
Product Information
Philips Pixel Defect Policy
Philips SmartControl ll
System support and
requirement
Installation
Start to use
Q&A
SmartControl II (Selective Models)
Philips SmartControl II
SmartControl II is monitor-based software with an easy-to-use on-screen graphic interface that guides you through fine-
tuning resolution, color calibration and other display settings including brightness, contrast, clock & phase, position, RGB,
white point and - on models with onboard speakers - volume adjustments.
System support and requirement:
1. Sytem support: 2000, XP, NT 4.0, XP 64 Edition, Vista 32/64. IE Support 6.0/7.0.
2. Language support: English, Simplified Chinese, German, Spanish, French, Italian, Russian, Portuguese.
3. Philips Monitor support DDC/CI Interface.
Installation:
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 1 頁 / 共 17 [98-07-01 15:10]
SmartControl
● Follow the instruction and complete the installation.
● You can lauch after installation complete.
● If you want to launch later, you can either click the shortcut on desktop or toolbar.
Start to use:
1. First launch -Wizard
● The first time after installation of SmartControl II, it will automatically go to Wizard for first time launch.
● The wizard will guide you through adjustment your monitor performance step by step.
● You can go to Plug-in menu to launch wizard later on as well.
● You can adjust more options without wizard by Standard pane.
Wizard Analog Sequence Wizard Digital Sequence
Resolution Resolution
Focus Contrast
Brightness Brightness
Contrast White Point (Color Temp)
Position File
White Point (Color Temp) -
File -
2. Start with Standard pane:
Adjust menu:
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 2 頁 / 共 17 [98-07-01 15:10]
SmartControl
● Adjust Menu allow you to adjust Brightness, Contrast, Focus, Position and Resolution.
● You can follow the instruction and do the adjustment.
● Cancel prompts user if you want to cancel installation.
Tab Heading Sub Menu Display in Analog Display in Digital
Adjust Brightness Yes Yes
Adjust Contrast Yes Yes
Adjust Focus (Clock & Clock Phase) Yes No
Adjust Position Yes No
Adjust Resolution Yes Yes
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 3 頁 / 共 17 [98-07-01 15:10]
SmartControl
Color menu:
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 4 頁 / 共 17 [98-07-01 15:10]
SmartControl
● Color Menu allow you to adjust RGB, Black Level, White Point, Color Calibration, and
SmartImage (Please refer to SmartImage section).
● You can follow the instruction and do the adjustment.
● Refer to below table for sub-menu item base on your input.
● Example for Color Calibration
Tab Heading Sub Menu Display in Analog Display in Digital
Color RGB Yes Yes
Color Black Level Yes Yes
Color White Point Yes Yes
Color Color Calibration Yes Yes
Color Viewing Mode Yes Yes
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 5 頁 / 共 17 [98-07-01 15:10]
SmartControl
1. "Show Me" starts color calibration tutorial.
2. Start - starts the 6-step color calibration sequence.
3. Quick View loads the before/after images.
4. To return to Color home pane, click the Cancel button.
5. Enable color calibration - by default is on. If unchecked, does not allow for color calibration to happen, dimes out start
and quick view buttons.
6. Must have patent info in calibration screen.
First color Calibration Screen:
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 6 頁 / 共 17 [98-07-01 15:10]
SmartControl
1. Previous button is disabled until the second color screen.
2. Next goes to the succeeding target (6-targets).
3. Final next goes File>Presets pane.
4. Cancel closes the UI and returns to the plug in page.
SmartImage - Allows user to change setting for better display setting based on content.
When Entertainment is set, SmartContrast and SmartResponse are enabled.
Plug-Ins - Asset Management Pane will only be active when selecting Asset Management from the drop-down
Plug Ins menu.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 7 頁 / 共 17 [98-07-01 15:10]
SmartControl
Displays Assent Management information on Managment, Description, Serial Number, Current Timing, Domain Name,
and Asset Management Status.
To return to Plug-in home pane select the plug-in tab.
Plug-Ins - Theft Deterrence Pane will only be active when selecting Theft Deterrence Mode from the drop-down
Plug Ins menu.
To enable Theft Deterrence, clicking Enable Theft Mode button brings up the following screen:
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 8 頁 / 共 17 [98-07-01 15:10]
SmartControl
1. User can enter PIN between 4 and 9 digits numbers only.
2. After entering PIN, Accept button takes user to the pop-up dialog box on the following page.
3. Minimum minutes set to 5. Slider set to 5 by default.
4. Does not require the display be attached to a different host to go into theft mode.
Once a PIN is entered and accepted, the following dialog box appears:
● Click on No button takes user to the following screen.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 9 頁 / 共 17 [98-07-01 15:10]
SmartControl
● Click on Yes button takes user to secure web site landing page.
After creating PIN, the Theft Deterrence pane will indicate Theft Deterrence Enabled and provide PIN Options button:
1. Theft Deterrence Enabled is displayed.
2. Disable Theft Mode opens pane screen on next page.
3. PIN Options button only available after user creates PIN, button opens secure PIN web site.
Disable Theft button opens the following pane:
1. After entering PIN, Accept button disables PIN.
2. Cancel button opens up main Theft Deterrence pane, displaying Theft Deterrence Disabled. Enable Theft Mode and
PIN Options buttons.
3. Entering incorrect PIN results in the following dialog box:
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 10 頁 / 共 17 [98-07-01 15:10]
SmartControl
Options>Preferences - Will only be active when selecting Preferences from the drop-down Options menu. On a
non-supported display capable of DDC/CI, only the Help and Options tabs are available.
1. Displays current preference settings.
2. A checked box enables the feature. The check box is a toggle.
3. Enable Context Menu on desktop is checked (On) by default. Enable Context menu displays SmartControl II selections for
Select Preset and Tune Display in the desktop right-click context menu. Disabled removes SmartControl II from the right click
context menu.
4. Enable Task Tray icon is checked (On) by default. Enable context menu shows the task tray menu for SmartControl II. A right
click on the task tray icon displays the menu options for Help, Technical Support. Check for Upgrade, About, and Exit.
When Enable task tray menu is disabled, the task tray icon will only display EXIT.
5. Run at Startup is checked (On) by default. When disabled, SmartControl II will not launch at start or be in the task tray. The
only way to launch SmartControll II is either from the desktop short cut or from the program file. Any preset set to run at
startup will not load when this box is unchecked (Disabled).
6. Enable transparency mode (Vista, XP, and 2k only). Default is 0% Opaque.
Options>Input - Will only be active when selecting Input from the drop-down Options menu. On a non-
supported display capable of DDC/CI, only the Help and Options tabs are available. All other SmartControl II tabs
are not available.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 11 頁 / 共 17 [98-07-01 15:10]
SmartControl
1. Display the Source instruction pane and current input source setting.
2. On single input displays, this pane will not be visible.
Options>Audio - Will only be active when selecting Volume from the drop-down Options menu.
On a non-supported display capable of DDC/CI, only the Help and Options tabs are available.
Option>Auto Pivot
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 12 頁 / 共 17 [98-07-01 15:10]
SmartControl
Help>User Manual - Will only be active when selecting User Manual from the drop-down Help menu. On a
non-supported display capable of DDC/CI, only the Help and Options tabs are available.
Help>Version - Will only be active when selecting Version from the drop- down Help menu. On a non-
supported display capable of DDC/CI, only the Help and Options tabs are available.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 13 頁 / 共 17 [98-07-01 15:10]
SmartControl
Context Sensitive menu
The Context Sensitive menu is Enabled by default. If Enable Context Menu has been checked in the
Options>Preferences pane, then the menu will be visible.
The Context Menu has four entries:
1. SmartControll II - When selected the About Screen is displayed.
2. Select Preset - Provides a hierarchical menu of saved presets for immediate use. A check mark shows the currently selected
preset. Facoty Preset can also be called from the drop down menu.
3. Tune Display - Opens the SmartControl II control panel.
4. Fly off for SmartImage - Check current settings, Off, Office Work, ImageViewing, Entertainment, Economy.
Task Tray Menu Enabled
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 14 頁 / 共 17 [98-07-01 15:10]
SmartControl
The task tray menu can be displayed by right-clicking on the SmartControl II icon from the task tray. Left Click will launch
the application.
The task tray has five entries:
1. Help - Access to User Manual file: opnes User Manual file using the default browser window.
2. Technical Support - displays the tech support page.
3. Check for Update - takes the user to PDI Landing and checks the user's version against the most current available.
4. About - Displays detailed reference information: product version, release information, and product name.
5. Exit - Close SmartControll II. To run SmartControll II again either select SmartControll II from Program menu, double-click the
desktop PC icon or restart the system.
Task Tray Menu Disabled
When the Task Tray is disabled in the preference folder, only the EXIT selection is available. To completely
remove SmartControll II from the task tray, disable Run at Startup in Options>Preferences.
Q&A
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 15 頁 / 共 17 [98-07-01 15:10]
SmartControl
Q1. I change the monitor on a PC to a different one and the SmartControl becomes un-usable, what do I do?
A. Restart your PC and see if SmartControl can work. Otherwise, you will need to remove and re-install SmartControl
to ensure proper driver is installed.
Q2. The SmartControl functions well at the beginning, but it is not workable, what can I do?
A. If the following actions were executed, the monitor driver may need to be re-installed.
● Change video graphic adapter to another one
● Update video driver
● Activities on OS, such as service pack or patch
● Run Windows Update and updated monitor and/or video driver
● Windows was booted with the monitor power off or disconnected.
To find out, please right click My Computer and click on Properties->Hardware-> Device Manager.
If you see "Plug and Play Monitor" shows under Monitor, then you need to re-install. Simply remove SmartControl and
re-install it.
Q3. After installing SmartControl, when clicking on SmartControl tab, nothing shows up after a while or a failure
message shows, what happened?
A. It might be your graphic adaptor is not compatible with the SmartControl. If your graphic adaptor is one of the
above mentioned brands, try to download the most updated graphic adaptor driver from corresponding companies web
site. Install the driver. Remove SmartControl, and re-install it once more.
If it is still not working, we are sorry that the graphic adaptor is not supported. Please pay attention to Philips web site for
any updated SmartControl driver available.
Q4. When I click on Product Information, only partial information is shown, what happened?
A. It might be your graphic card adaptor driver is not the most updated version which fully supporting DDC/CI
interface. Please try to download the most updated graphic adaptor driver from corresponding companies web site. Install
the driver. Remove SmartControl, and re-install it once more.
Q5. I forgot my PIN for Theft Deterrence Function. How can I do?
A. Please contact IT manager or Philips Service Center.
Q6. In a monitor with the Smartlmage feature, the sRGB scheme of color temperature function in SmartControl is
not responding, why?
A. When Smartlmage is enabled, the sRGB scheme is disabled automatically. To use sRGB, you need to
disable Smartlmage with the button at the front bezel of your monitor.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...new-format/CD-Contents/lcd/manual/ENGLISH/225B1/product/SMART.HTM 第 16 頁 / 共 17 [98-07-01 15:10]
Installing Your LCD Monitor
Front View Product Description
Connecting to Your PC
The Base
Getting Started
Optimizing Performance
Installing Your LCD Monitor
Front View Product Description
1 To switch monitor's power On and Off
2To access OSD menu
3 To adjust the OSD menu
4To adjust brightness of the display
5To adjust volume of the display
6
PowerSensor. To automatically dim down brightness level when no
users are in front of the monitor for saving power and prolonging the life
of your monitor. The higher the value, the more sensible PowerSensor
functions / Return to previous OSD level
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/install.htm 第 1 頁 / 共 3 [98-07-01 15:10]
Installing Your LCD Monitor
7SmartImage. There are five modes to be selected: Office Work, Image
Viewing, Entertainment, Economy, and Off
8Earphone jack
RETURN TO TOP OF THE PAGE
Rear View
1 USB upstream port and downstream port
2 VGA input
3 DVI-D input (available for selective models)
4 AC power input
5 PC Audio input
6 Kensington anti-thief lock
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/install.htm 第 2 頁 / 共 3 [98-07-01 15:10]
Installing Your LCD Monitor
Optimizing Performance
● For best performance, ensure that your display settings are set at 1680x1050, 60Hz.
Note: You can check the current display settings by pressing the 'OK' button
once. The current display mode is shown in OSD main controls called
RESOLUTION.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....03-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/install.htm 第 3 頁 / 共 3 [98-07-01 15:10]
Connecting to Your PC
Front View Product
Description
Accessory Pack
Connecting to Your PC
Getting Started
Optimizing Performance
The Base
Connecting to Your PC
Accessory Pack
Unpack all the parts.
Power cord DVI cable (Optional)
VGA cable (Optional) EDFU pack
Audio cable
RETURN TO TOP OF THE PAGE
Connecting to Your PC
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...w-format/CD-Contents/lcd/manual/ENGLISH/225B1/INSTALL/CONNECT.HTM 第 1 頁 / 共 3 [98-07-06 09:28]
Connecting to Your PC
1) Connect the power cord to the back of the monitor firmly. (Philips has pre-connected
VGA cable for the first installation.
*available for selective models
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...w-format/CD-Contents/lcd/manual/ENGLISH/225B1/INSTALL/CONNECT.HTM 第 2 頁 / 共 3 [98-07-06 09:28]
Connecting to Your PC
*available for selective models
2) Connect to PC
(a) Turn off your computer and unplug its power cable.
(b) Connect the monitor signal cable to the video connector on the back of your
computer.
(c) Connect the PC audio cable to the audio connector on the back of your
computer.
(d)
Connect the USB upstream port on the monitor and the USB port on PC with
a USB cable. The USB downstream port is now ready for any USB device to
plug in.
(e) Plug the power cord of your computer and your monitor into a nearby outlet.
(f) Turn on your computer and monitor. If the monitor displays an image,
installation is complete.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDF...w-format/CD-Contents/lcd/manual/ENGLISH/225B1/INSTALL/CONNECT.HTM 第 3 頁 / 共 3 [98-07-06 09:28]
The Base
Install base stand
Remove base stand
Front View Product
Description
Accessory Pack
Connecting to your PC
Getting Started
Optimizing Performance
Remove the Base
The Base
Install base stand
225B1
(a) Place the monitor base stand on a stable surface.
(b) Firmly grasp the monitor with both hands.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/base.htm 第 1 頁 / 共 8 [98-07-01 15:10]
The Base
(c) Attach the monitor stand to the monitor column until the tabs "click" into place before
releasing the height adjustable column.
Remove base stand
225B1
Before you start disassembling the monitor base, please follow the instructions below to
avoid damage or injury.
a) Extend the monitor stand to its maximum height.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/base.htm 第 2 頁 / 共 8 [98-07-01 15:10]
The Base
(b) Place the monitor face down on a smooth surface, taking care to avoid scratching or
damaging the screen. Then lift the monitor stand.
(c) Press the release button on the rear of the stand to remove the base from the stand.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/base.htm 第 3 頁 / 共 8 [98-07-01 15:10]
The Base
Remove the Base
Condition:
● for VESA standard mounting applications
(a) Remove the 4 screw covers.
225P1
225B1
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/base.htm 第 4 頁 / 共 8 [98-07-01 15:10]
The Base
(b) Remove the 4 screws and then remove the base from the LCD monitor.
225P1
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/base.htm 第 5 頁 / 共 8 [98-07-01 15:10]
The Base
225B1
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/base.htm 第 6 頁 / 共 8 [98-07-01 15:10]
The Base
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/base.htm 第 7 頁 / 共 8 [98-07-01 15:10]
Getting Started
Your LCD Monitor :
Front View Product
Description
Setting Up and Connecting
Your Monitor
Getting Started
Optimizing Performance
Getting Started
Getting Started
Use the information file ( .inf) for Windows® 2000/XP/Vista or later
The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for
Windows® 2000/XP/Vista. This information file ( .inf) should be installed in order that your
Philips monitor can be enabled from the 'Monitor' dialog box in Windows® 2000/XP/Vista and
the Plug & Play application can be activated. The installation procedure based on Windows®
2000 , XP and Vista is specified as follows.
For Windows® 2000
1. Start Windows® 2000
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select 'Monitor'
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps
given below.
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.
7. Select 'Display a list of the known drivers for this device so that I can choose a specific
driver', then click on 'Next' and then click on 'Have disk...'.
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).
9. Click on the 'Open' button, then click on the 'OK' button.
10. Select your monitor model and click on the 'Next' button.
11. Click on the 'Finish' button then the 'Close' button.
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
For Windows® XP
1. Start Windows® XP
2. Click on the 'Start' button and then click on 'Control Panel'.
3. Select and click on the category 'Printers and Other Hardware'
4. Click on the 'Display' Item.
5. Select the 'Settings' tab then click on the 'Advanced' button.
6. Select 'Monitor' tab
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please
stop installation.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/gt_start.htm 第 1 頁 / 共 2 [98-07-01 15:11]
Getting Started
- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on
the 'Next' button.
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the
'Next' button.
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the
appropriate drive F: (CD-ROM Drive).
11. Click on the 'Open' button, then click the 'OK' button.
12. Select your monitor model and click on the 'Next' button.
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with
Windows® XP' message, please click on the 'Continue Anyway' button.
13. Click on the 'Finish' button then the 'Close' button.
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties
dialog box.
For Windows® Vista
1. Start Windows® Vista
2. Click the Start button; select and click on 'Control Panel'.
3. Select and click on 'Hardware and Sound'
4. Choose 'Device Manager' and Click on 'Update device drivers'.
5. Select 'Monitor' and then right click on 'Generic PnP Monitor'.
6. Click on 'Update Driver Software'.
7. Select 'Browse my computer for driver software'.
8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:
(CD-ROM Drive:\\Lcd\PC\drivers\).
9. Click the 'Next' button.
10. Wait few minutes for installing the driver, and then click 'Close' button.
If your Windows® 2000/XP/Vista version is different or you need more detailed installation
information, please refer to your Windows® 2000/XP/Vista user's manual.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/install/gt_start.htm 第 2 頁 / 共 2 [98-07-01 15:11]
On-Screen Display
Description of the On-Screen
Display
The OSD Tree
On-Screen Display
Description of the On Screen Display
What is the On-Screen Display?
On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust
screen performance or select functions of the monitors directly through an on-screen instruction
window. A user friendly on screen display interface is shown as below :
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/osd/osddesc.htm 第 1 頁 / 共 4 [98-07-01 15:11]
On-Screen Display
Basic and simple instruction on the control keys.
In the OSD shown above users can press buttons at the front bezel of the monitor to move
the cursor, to confirm the choice or change.
RETURN TO TOP OF THE PAGE
The OSD Tree
Below is an overall view of the structure of the On-Screen Display. You can use this as a reference
when you want to work your way around the different adjustments later on.
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/osd/osddesc.htm 第 2 頁 / 共 4 [98-07-01 15:11]
On-Screen Display
Resolution notification
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/osd/osddesc.htm 第 3 頁 / 共 4 [98-07-01 15:11]
On-Screen Display
This monitor is designed for optimal performance at its native resolution, 1680X1050@60Hz. When
the monitor is powered on at a different resolution, an alert is displayed on screen: Use
1680x1050@60Hz for best results.
Display of the native resolution alert can be switched off from Setup in the OSD (On Screen
Display) menu.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5....003-new-format/CD-Contents/lcd/manual/ENGLISH/225B1/osd/osddesc.htm 第 4 頁 / 共 4 [98-07-01 15:11]
Customer Care & Warranty
Customer Care & Warranty
PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR
WARRANTY COVERAGE
WESTERN EUROPE: Austria Belgium Denmark France Germany
Greece Finland Ireland Italy Luxembourg the Netherlands Norway
Portugal Sweden Switzerland Spain United Kingdom Poland
EASTERN EUROPE: Czech Republic Hungary Russia Slovakia Slovenia
Turkey
LATIN AMERICA: Argentina Brasil
NORTH AMERICA: Canada USA
PACIFIC: Australia New Zealand
ASIA: China Hong Kong India Indonesia Korea Malaysia Pakistan
Philippines Singapore Taiwan Thailand Vietnam
AFRICA: South Africa
MIDDLE EAST: United Arab Emirates
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B.0QC01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warranty.htm [98-07-01 15:11]
Your Philips F1rst Choice Warranty
Your Philips F1rst Choice Warranty
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and deliver
high-quality performance, ease of use and ease of installation. Should you
encounter any difficulties while installing or using this product, please contact the
Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty. This
three-year service warranty entitles you to a swap model on-site if your monitor
turns out to be faulty or defective. Philips aims at a swap within 48 hours of your
call being received.
What is covered?
The Philips F1rst Choice Warranty applies within Andorra, Austria, Belgium, Cyprus, Denmark,
France, Germany, Greece, Finland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, the
Netherlands, Norway, Poland, Portugal, Sweden, Switzerland, Spain and the United Kingdom and
only for monitors originally designed, manufactured, approved and/or authorized for usage within
these countries.
Warranty coverage begins as from the day you buy your monitor. For three years thereafter, your
monitor will be swapped by at least an equivalent monitor in case of defects provided for under the
warranty coverage.
The swap monitor remains yours and Philips keeps the defective/original monitor. For the swap
monitor the warranty period remains equal to that of your original monitor, being 36 months as from
the purchase date of your original monitor.
What is excluded?
The Philips F1rst Choice Warranty applies provided the product is handled properly for its intended
use, in accordance with its operating instructions and upon presentation of the original invoice or
cash receipt, indicating the date of purchase, dealer's name and model and production number of
the product.
The Philips F1rst Choice Warranty may not apply if:
● The documents have been altered in any way or made illegible;
● The model or production number on the product has been altered, deleted, removed or made
illegible;
● Repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
● Damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect;
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...1.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_1st.htm 第 1 頁 / 共 3 [98-07-01 15:11]
Your Philips F1rst Choice Warranty
● Reception problems caused by signal conditions or cable or antenna systems outside the
unit;
● Defects caused by abuse or misuse of the monitor;
● Product requires modification or adaptation to enable it to comply with local or national
technical standards, which apply in countries for which the product was not originally
designed, manufactured, approved and/or authorized. Therefore always check whether a
product can be used in a specific country.
● Note that products that are not originally designed, manufactured, approved and/or
authorized for usage within the Philips F1rst Choice countries, do not apply to the Philips
F1rst Choice Warranty. In these cases the Philips global warranty terms are valid.
Just a click away
In case of any problems, we advise you to read the operating instructions carefully or go to the www.
philips.com/support website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully or go to the www.philips.com/support website for additional support before contacting the
Philips helpdesk.
To solve your problem quickly, please prepare the following details before contacting the Philips
helpdesk:
● Philips type number
● Philips serial number
● Purchase date (copy of purchase may be required)
● PC environment Processor:
❍ CUP and Graphic card name and driver version
❍ Operating system
❍ Application being used
● Other cards installed
Having the following information available will also help speed up the process:
● Your proof of purchase indicating: date of purchase, dealer name, model and product serial
number.
● The full address to which the faulty monitor has to be collected and the swap model should
be delivered.
Philips' customer help desks are located worldwide. Click here to access the F1rst Choice Contact
Information.
Or you can reach us via:
Website: http://www.philips.com/support
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...1.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_1st.htm 第 2 頁 / 共 3 [98-07-01 15:11]
Your Philips F1rst Choice Warranty
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...1.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_1st.htm 第 3 頁 / 共 3 [98-07-01 15:11]
F1rst Choice Contact Information
F1rst Choice Contact Information
Country Code Telephone number Tariff
Austria +43 0810 000206 € 0.07
Belgium +32 078 250851 € 0.06
Denmark +45 3525 8761 Local call tariff
Finland +358 09 2290 1908 Local call tariff
France +33 082161 1658 € 0.09
Germany +49 01803 386 853 € 0.09
Greece +30 00800 3122 1223 Free of charge
Ireland +353 01 601 1161 Local call tariff
Italy +39 840 320 041 € 0.08
Luxembourg +352 26 84 30 00 Local call tariff
The Netherlands +31 0900 0400 063 € 0.10
Norway +47 2270 8250 Local call tariff
Poland +48 0223491505 Local call tariff
Portugal +351 2 1359 1440 Local call tariff
Spain +34 902 888 785 € 0.10
Sweden +46 08 632 0016 Local call tariff
Switzerland +41 02 2310 2116 Local call tariff
United Kingdom +44 0207 949 0069 Local call tariff
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B.0QC01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warfirst.htm [98-07-01 15:11]
Your Guarantee in Central and Eastern Europe
Your Guarantee in Central and Eastern Europe
Dear Customer,
Thank you for purchasing this Philips product, which has been designed and manufactured to the
highest quality standards. If, unfortunately, something should go wrong with this product Philips
guarantees free of charge labor and replacement parts during a period of 36 months from date of
purchase.
What is covered?
This Philips Guarantee in Central and Eastern Europe applies within Czech Republic, Hungary,
Slovakia, Slovenia, Russia and Turkey and only for monitors originally designed, manufactured,
approved and/or authorized for usage within these countries.
Warranty coverage begins as from the day you buy your monitor. For 3 years thereafter, your
monitor will be serviced in case of defects provided for under the warranty coverage.
What is excluded?
The Philips guarantee applies provided the product is handled properly for its intended use, in
accordance with its operating instructions and upon presentation of the original invoice or cash
receipt, indicating the date of purchase, dealer's name and model and production number of the
product.
The Philips guarantee may not apply if:
● the documents have been altered in any way or made illegible;
● the model or production number on the product has been altered, deleted, removed or made
illegible;
● repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
● damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect.
● Reception problems caused by signal conditions or cable or antenna systems outside the
unit;
● Defects caused by abuse or misuse of the monitor;
● Product requires modification or adaptation to enable it to comply with local or national
technical standards, which apply in countries for which the product was not originally
designed, manufactured, approved and/or authorized. Therefore always check whether a
product can be used in a specific country.
Please note that the product is not defective under this guarantee in the case where modifications
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_ee.htm 第 1 頁 / 共 2 [98-07-01 15:11]
Your Guarantee in Central and Eastern Europe
become necessary in order for the product to comply with local or national technical standards
which apply in countries for which the product was not originally designed and/or manufactured.
Therefore always check whether a product can be used in a specific country.
Just a click away
In case of any problems, we advise you to read the operating instructions carefully or go to the www.
philips.com/support website for additional support.
Just a phone call away
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully before contacting our dealers or Information Centers
In case your Philips product is not working correctly or is defective, please contact your Philips
dealer or directly the Philips Service and Consumer Information Centers
Website: http://www.philips.com/support
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_ee.htm 第 2 頁 / 共 2 [98-07-01 15:11]
Consumer Information Centers
Consumer Information Centers
Argentina Australia Brasil Canada New Zealand Belarus Bulgaria
Croatia Czech Republic Estonia United Arab Emirates Hong Kong
Hungary India Indonesia Israel Latvia Lithuania Malaysia
Middle East + North Africa New Zealand Pakistan Romania Russia
Serbia & Montenegro Singapore Slovakia Slovenia South Africa
South Korea Taiwan Philippines Thailand Turkey Ukraine Vietnam
Eastern Europe
BELARUS
Technic al Center of JV IBA
M. Bogdanovich str. 155
BY - 220040 Minsk
Tel: +375 17 217 33 86
BELARUS
Service.BY
Petrus Brovky st. 19 – 101-B
220072, Minsk
Belarus
BULGARIA
LAN Service
140, Mimi Balkanska Str.
Office center Translog
1540 Sofia, Bulgaria
Tel: +359 2 960 2360
www.lan-service.bg
CZECH REPUBLIC
General Consumer Information Center
800 142100
Xpectrum
Lu.ná 591/4
CZ - 160 00 Praha 6 Tel: 800 100 697 or 220 121 435
Email:info@xpectrum.cz
www.xpectrum.cz
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warcic.htm 第 1 頁 / 共 9 [98-07-01 15:12]
Consumer Information Centers
CROATIA
Renoprom d.o.o.
Ljubljanska 4,
Sv. Nedjelja,10431
Croatia
Tel: +385 1 333 0974
ESTONIA
FUJITSU SERVICES OU
Akadeemia tee 21G
EE-12618 Tallinn
Tel: +372 6519900
www.ee.invia.fujitsu.com
HUNGARY
Serware Szerviz
Vizimolnár u. 2-4
HU - 1031 Budapest
Tel: +36 1 2426331
Email: inbox@serware.hu
www.serware.hu
HUNGARY
Profi Service Center Ltd.
123 Kulso-Vaci Street,
H-1044 Budapest ( Europe Center )
Hungary
Tel: +36 1 814 8080
m.andras@psc.hu
LATVIA
ServiceNet LV
Jelgavas iela 36
LV - 1055 Riga,
Tel: +371 7460399
Email: serviss@servicenet.lv
LITHUANIA
ServiceNet LT
Gaiziunu G. 3
LT - 3009 KAUNAS
Tel: +370 7400088
Email: servisas@servicenet.lt
www.servicenet.lt
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warcic.htm 第 2 頁 / 共 9 [98-07-01 15:12]
Consumer Information Centers
ROMANIA
Blue Ridge Int'l Computers SRL
115, Mihai Eminescu St., Sector 2
RO - 020074 Bucharest
Tel: +40 21 2101969
SERBIA & MONTENEGRO
Kim Tec d.o.o.
Viline vode bb, Slobodna zona
Beograd L12/3
11000 Belgrade
Serbia
Tel. +381 11 20 70 684
SLOVAKIA
General Consumer Information Center
0800004551
Datalan Servisne Stredisko
Puchovska 8
SK - 831 06 Bratislava
Tel: +421 2 49207155
Email: servis@datalan.sk
SLOVENIA
PC HAND
Brezovce 10
SI - 1236 Trzin
Tel: +386 1 530 08 24
Email: servis@pchand.si
RUSSIA
CPS
18, Shelepihinskaya nab.
123290 Moscow
Russia
Tel. +7(495)797 3434
Profservice:
14A -3, 2Karacharovskaya str,
109202, Moscow ,
Russia
Tel. +7(095)170-5401
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warcic.htm 第 3 頁 / 共 9 [98-07-01 15:12]
Consumer Information Centers
TURKEY
Türk Philips Ticaret A.S.
Yukari Dudullu Org.San.Bolgesi
2.Cadde No:22
34776-Umraniye/Istanbul
Tel: (0800)-261 33 02
UKRAINE
Comel
Shevchenko street 32
UA - 49030 Dnepropetrovsk
Tel: +380 562320045
www.csp-comel.com
LLC Topaz Company
Topaz-Service Company,
Mishina str. 3,
Kiev
Ukraine-03151
Tel: +38 044 245 73 31
Latin America
ARGENTINA
Azopardo 1480.
(C1107ADZ) Cdad. de Buenos Aires
Tel: 0800 3330 856
Email: CIC.monitores@Philips.com
BRASIL
Alameda Raja Gabaglia, 188 - 10°Andar - V.
Olímpia - S. Paulo/SP - CEP 04551-090 -
Brasil
Tel: 0800-7254101
Email: CIC.monitores@Philips.com
Pacific
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warcic.htm 第 4 頁 / 共 9 [98-07-01 15:12]
Consumer Information Centers
AUSTRALIA
Company: AGOS NETWORK PTY LTD
Address: 4/5 Dursley Road, Yenorra, NSW 2161, Australia
Tel: 1300 360 386
Fax: +61-2-80808147
Email: philips@agos.com.au
Service hours: Mon.~Fri. 8:00am-7:30pm
NEW ZEALAND
Company: Visual Group Ltd.
Address: 28 Walls Rd Penrose Auckland
Phone: 0800 657447
Fax: 09 5809607
E-mail: vai.ravindran@visualgroup.co.nz
Service Hours: Mon.~Fri. 8:30am~5:30pm
Asia
HONG KONG/Macau
Company Name: PHK Service Limited
Address: Flat A, 10/F., Pak Sun Building, 103 - 107 Wo Yi Hop Road, Kwai Chung, New Territories, Hong
Kong
Tel.: (852) 2610-6908 / (852) 2610-6929 for Hong Kong and (853) 2856-2277 for Macau
Fax: (852) 2485 3574 for Hong Kong and (853) 2856 1498 for Macau
E-mail: enquiry@phkservice.com.hk
Service Hours: Mon.~Sat. 09:00am~06:00pm
India
Company: REDINGTON INDIA LTD
Address: SPL Guindy House, 95 Mount Road, Chennai 600032, India
Tel: +9144-42243352/353
E-mail: aftersales@in.aocmonitor.com
Service hours: Mon.~Fri. 9:00AM~5:30PM; Sat. 9:00AM~1:00PM
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warcic.htm 第 5 頁 / 共 9 [98-07-01 15:12]
Consumer Information Centers
Indonesia
Company Name: PT. Gadingsari elektronika Prima
Address: Kompleks Pinang 8, Jl. Ciputat raya No. 8F, Pondok Pinang. Jakarta
Tel: 021-750909053, 021-750909056
Fax: 021-7510982
E-mail: gepta@cbn.net.id
Service hours: Mon.~Fri. 8:30am~4:30pm; Sat. 8:30am~2:00pm
Additional service points:
1. Philips Building Jl. Buncit Raya Kav 99. Jakarta Selatan.
Phone: 021-7940040, ext 1722/1724, 98249295, 70980942
2. Jl. Tanah Abang 1 no 12S. Jakarta Pusat.
Phone: 021-3455150, 34835453
3. Rukan City Home no H31, Gading Square. Jl. Bulevar Barat. Kelapa Gading. Jakarta Utara. Phone: 021-
45870601, 98131424
South Korea
Company: PCS One Korea Ltd.
Address: 112-2, Banpo-dong, Seocho-ku, Seoul, 137-040, Korea
Call Center Tel: 080-600-6600
Tel: 82 2 591 1528
Fax: 82 2 595 9688
E-mail: cic_korea@philips.com
Service hours: Mon.~Fri. 9:00AM~ 6:00PM; Sat. 9:00AM~1:00PM
Malaysia
Company: After Market Solutions (CE) Sdn Bhd
Address: Lot 6. Jalan 225/51A, 46100 Petaling Jaya, Selangor DE, Malaysia.
Phone: 603 7953 3370
Philips Info Line: 1-800-880-180
Fax: 603 7953 3338
E-mail: pceinfo.my@philips.com
Service Hours: Mon.~Fri. 8:15am~5:15pm; Sat. 9:00am~1:00pm
Pakistan
Philips Consumer Service
Address: Mubarak manzil, 39, Garden Road, Saddar, Karachi-74400
Tel: (9221) 2737411-16
Fax: (9221) 2721167
E-mail: care@philips.com
Website: www.philips.com.p
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warcic.htm 第 6 頁 / 共 9 [98-07-01 15:12]
Consumer Information Centers
Singapore
Company: Philips Electronics Singapore Pte Ltd (Philips Consumer Care Center)
Address: 620A Lorong 1 Toa Payoh, TP4 Building Level 1, Singapore 319762
Tel: (65) 6882 3999
Fax: (65) 62508037
E-mail: consumer.care.sg@philips.com
Service hours: Mon.~Fri. 9:00am~6:00pm; Sat. 9:00am~1:00pm
Taiwan
Company: FETEC.CO
Address: 3F, No.6, Lane 205, Sec. 1, Chang Hsing Rd, Lu Chu Hs, Taoyuan, Taiwan R.O.C 33800
Consumer Care: 0800-231-099
Tel: (03)2120336
Fax: (03)3129184
E-mail: knlin08@xuite.net
Service hours: Mon.~Fri. 8:30am~7:00pm
Thailand
Company: Axis Computer System Co., Ltd.
Address: 1421 Soi Lardprao 94, Srivara Town In Town Soi 3 Road, Wangthonglang, Bangkok 10310
Thailand
Tel: (662) 934-5498
Fax: (662) 934-5499
E-mail: axis5@axiscomputer.co.th
Service Hours: Mon.~Fri. 08:30am~05:30pm
Vietnam
Company: Digiworld Corp
Address: 211-213 Vo Van Tan St, Ward 5, Dist.3 , Ho Chi Minh city, Vietnam
Tel: 848-38266065
Fax: 848-38267307
E-mail: Digicare@dgw.com.vn
Service hours: 8:00 to 12:00 AM and 13:30 to 17:30 PM (from Monday to Friday)
Philippines
Glee Electronics Inc
Contact nos. (632) 636-3636 / 7064028 to 29
Fax no. (632) 7064026
Receiving Centers
NEO CARE - Megamall
4th Level Cyberzone, Building B,
SM Megamall, Mandaluyong City
NEO CARE - SM North EDSA
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warcic.htm 第 7 頁 / 共 9 [98-07-01 15:12]
Consumer Information Centers
4th Level Cyberzone, Annex Bldg.
SM City North EDSA, Quezon City
441-1610
MDR Microware Sales Inc.
Cebu Branch
N. Escario corner Clavano St., Cebu City Phils.
# 255-4415/ 255-3242/253-9361/4124864 to 67
Sun # 0922-8210045 to 46
Davao Office:
C. Arellano St., Davao City 8000
082- 225-3021/225-3022
Sun# 0922-8210015
CDO Office:
1445 Corrales Ext.,CDO City
088-856-8540/856-8541
Sun # 0922-8210080
Iloilo Office:
C. Lim Comp., Gomez St., Iloilo City
# 033 338-4159/ 033 508-3741
Sun # 0922-8808850
Africa
SOUTH AFRICA
Company name: Sylvara Technologies Pty Ltd
Address: Ho Address Palm Springs Centre Christoffel Road Van Riebeeck Park Kempton Park, South Africa
Tel: +27878084456
Fax: +2711 391 1060
E-mail: customercare@philipssupport.co.za
Service hours: Mon.~ Fri. 08:00am~05:00pm
Middle East
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warcic.htm 第 8 頁 / 共 9 [98-07-01 15:12]
Consumer Information Centers
Middle East + North Africa
Company: AL SHAHD COMPUTER L.L.C
Address: P.O.BOX: 29024, DUBAI, UNITED ARAB EMIRATES
TEL: 00971 4 2276525
FAX: 00971 4 2276242
E-mail: shahd52@eim.ae
Service hours: Sat.~Thur. 9:00am~1:00pm & 4:00pm- 8:00pm
Israel
Company: Eastronics LTD
Address: 13 Rozanis St. P.O.B. 39300, Tel Aviv 61392 Israel
Tel: 1-800-567000 call free in Israel; (972-50-8353722 after service hours until 20:00)
Fax: 972-3-6458759
E-mail: eastronics@eastronics.co.il
Service hours: Sun.~Thurs. 08:00 - 18:00
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...01.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/warcic.htm 第 9 頁 / 共 9 [98-07-01 15:12]
International Guarantee
Your International Guarantee
Dear Customer,
Thank you for purchasing this Philips product which has been designed and manufactured to the
highest quality standards.
If, unfortunately, something should go wrong with this product Philips guarantees free of charge
labor and replacement parts irrespective of the country where it is repaired during a period of 12
months from date of purchase. This international Philips guarantee complements the existing
national guarantee obligations to you of dealers and Philips in the country of purchase and does not
affect your statutory rights as a customer.
The Philips guarantee applies provided the product is handled properly for its intended use, in
accordance with its operating instructions and upon presentation of the original invoice or cash
receipt, indicating the date of purchase, dealer's name and model and production number of the
product.
The Philips guarantee may not apply if:
● the documents have been altered in any way or made illegible;
● the model or production number on the product has been altered, deleted, removed or made
illegible;
● repairs or product modifications and alterations have been executed by unauthorized service
organizations or persons;
● damage is caused by accidents including but not limited to lightning, water or fire, misuse or
neglect.
Please note that the product is not defective under this guarantee in the case where modifications
become necessary in order for the product to comply with local or national technical standards
which apply in countries for which the product was not originally designed and/or manufactured.
Therefore always check whether a product can be used in a specific country.
In case your Philips product is not working correctly or is defective, please contact your Philips
dealer. In the event you require service whilst in another country a dealer address can be given to
you by the Philips Consumer Help Desk in that country, the telephone and fax number of which can
be found in the relevant part of this booklet.
In order to avoid unnecessary inconvenience, we advise you to read the operating instructions
carefully before contacting your dealer. If you have questions which your dealer cannot answer or
any related question please contact the Philips Consumer Information Centers or via:
Website: http://www.philips.com
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...1.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_intl.htm 第 1 頁 / 共 2 [98-07-01 15:12]
International Guarantee
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5B...1.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_intl.htm 第 2 頁 / 共 2 [98-07-01 15:12]
United States Guarantee
Your Philips F1rst Choice Warranty(USA)
Thank you for purchasing this Philips monitor.
All Philips monitors are designed and manufactured to high standards and
deliver high-quality performance, ease of use and ease of installation. Should
you encounter any difficulties while installing or using this product, please
contact Philips directly to benefit from your Philips F1rst Choice Warranty. This
three-year service warranty entitles you to a swap model on-site within 48
hours of your call being received within the first year of purchase. If you have
any problems with your monitor within the second or third year of purchase, we
will repair it after it has been sent to the service provider at your expense and
returned to you within five working days, free of charge.
LIMITED WARRANTY (Computer Monitor)
Click here to access the Warranty Registration Card.
Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange*
*Product will be exchanged with a new or renewed to original specifications unit within two
business days for the first year. This product must be shipped in at your expense for service during
years two and three.
WHO IS COVERED?
You must have proof of purchase to receive warranty service. A sales receipt or other document
showing that you purchased the product is considered proof of purchase. Attach it to this owner's
manual and keep both nearby.
WHAT IS COVERED?
Warranty coverage begins the day you buy your product. For three years thereafter, all parts will be
repaired or replaced, and labor is free. After three years from the day of purchase, you pay for the
replacement or repair of all parts, and for all labor charges.
All parts, including repaired and replaced parts, are covered only for the original warranty period.
When the warranty on the original product expires, the warranty on all replaced and repaired
products and parts also expires.
WHAT IS EXCLUDED?
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...1.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_usa.htm 第 1 頁 / 共 4 [98-07-01 15:12]
United States Guarantee
Your warranty does not cover:
● labor charges for installation or setup of the product, adjustment of customer controls on the
product, and installation or repair of antenna systems outside of the product.
● product repair and/or part replacement because of misuse, accident, unauthorized repair or
other cause not within the control of Philips Consumer Electronics.
● reception problems caused by signal conditions or cable or antenna systems outside the
unit.
● a product that requires modification or adaptation to enable it to operate in any country other
than the country for which it was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications.
● incidental or consequential damages resulting from the product. (Some states do not allow
the exclusion of incidental or consequential damages, so the above exclusion may not apply
to you. This includes, but is not limited to, prerecorded material, whether copyrighted or not
copyrighted.)
● the model or production number on the product has been altered, deleted, removed or made
illegible.
Where IS SERVICE AVAILABLE?
Warranty service is available in all countries where the product is officially distributed by Philips
Consumer Electronics. In countries where Philips Consumer Electronics does not distribute the
product, the local Philips service organization will attempt to provide service (although there may be
a delay if the appropriate spare parts and technical manual(s) are not readily available).
Where CAN I GET MORE INFORMATION?
For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A.
customers only) or (919) 573-7855.
Before Requesting Service...
Please check your owner's manual before requesting service. Adjustments of the controls
discussed there may save you a service call.
TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS...
Contact the Philips Customer Care Center phone number listed below for product assistance and
procedures for servicing:
Philips Customer Care Center
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...1.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_usa.htm 第 2 頁 / 共 4 [98-07-01 15:12]
United States Guarantee
(877) 835-1838 or (919) 573-7855
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties
of merchantability and fitness for a particular purpose, are limited in duration to the duration of this
express warranty. But, because some states do not allow limitations on how long an implied
warranty may last, this limitation may not apply to you.)
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
(800) 479-6696
Three years free parts and three years free labor will be provided at Philips Canada depot or any
one of its authorized service centers.
(In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed
or implied, including any implied warranties of merchantability or fitness for a particular purpose.
Philips is not liable under any circumstances for any direct, indirect, special, incidental or
consequential damages, howsoever incurred, even if notified of the possibility of such damages.)
REMEMBER... Please record the model and serial numbers found on the product below.
MODEL # ________________________________________________
SERIAL # ________________________________________________
This warranty gives you specific legal rights. You may have other rights which vary from state/
province to state/province.
Before contacting Philips, please prepare the following details so we can solve your problem
quickly.
● Philips type number
● Philips serial number
● Purchase date (copy of purchase may be required)
● PC environment Processor:
❍ CUP and Graphic card name and driver version
❍ Operating system
❍ Application being used
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...1.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_usa.htm 第 3 頁 / 共 4 [98-07-01 15:12]
United States Guarantee
● Other cards installed
Having the following information available will also help speed up the process:
● Your proof of purchase indicating: date of purchase, dealer name, model and product serial
number.
● The full address to which the swap model should be delivered.
Just a phone call away
Philips customer help desks are located worldwide. Within the U.S. you can contact Philips
customer care Monday-Friday from 8:00 AM-9:00 PM Eastern Time (ET) and on Saturdays from
10:00 AM-5:00 PM ET hrs by using one of the contact phone numbers.
For more information on this and more great Philips products visit our website at:
Website: http://www.philips.com
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5...1.003-new-format/CD-Contents/lcd/manual/ENGLISH/warranty/war_usa.htm 第 4 頁 / 共 4 [98-07-01 15:12]
Download and Print
Installing your LCD monitor
driver
Download and Printing
Instructions
Download and Print
Installing Your LCD monitor driver
System requirements:
● PC running Windows® 2000 , Windows® XP, Windows® Vista or later
● Find your driver ".inf/.icm/.cat" at : /PC/drivers/
Read the "Readme.txt" file before installing.
Add” refer to http://www.p4c.philips.com/ to download the latest version of monitor drivers.”
This page provides an option to read the manual in .pdf format. PDF files can be downloaded into
your hard disk, then viewed and printed with Acrobat Reader or through your browser.
If you do not have Adobe® Acrobat Reader installed, click on the link to install the application.
Adobe® Acrobat Reader for PC / Adobe® Acrobat Reader for Apple Macintosh.
Download instructions:
To download the file:
1. Click-and-hold your mouse over the icon below. (Windows® 95/98/2000/Me/XP/Vista users right-
click)
Download 225P1/225B1.pdf
2. From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to
Disk'.
3. Choose where you would like to save the file; click 'Save' (if prompted to save as either 'text' or
'source', choose 'source').
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5....003-new-format/CD-Contents/lcd/manual/ENGLISH/download/download.htm 第 1 頁 / 共 2 [98-07-01 15:12]
Download and Print
Printing instructions:
To print the manual:
With the manual file open, follow your printer's instructions and print the pages you need.
RETURN TO TOP OF THE PAGE
file:///E|/LCD%20Monitor%20OEM/Philips/M1-project/225B1/225B1-EDFU/5....003-new-format/CD-Contents/lcd/manual/ENGLISH/download/download.htm 第 2 頁 / 共 2 [98-07-01 15:12]