Table of Contents
Philips 32BDL3010Q/00 User Manual
Displayed below is the user manual for 32BDL3010Q/00 by Philips which is a product in the Signage Displays category. This manual has pages.
Related Manuals
www.philips.com/welcome
32BDL3010Q
V1.00
User Manual (English)
i
Safety Instructions
Warnings and Precautions
KNOW THESE SAFETY SYMBOLS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol indicates high voltage is present inside.
It is dangerous to make any kind of contact with any
inside part of this product.
This symbol alerts you that important literature
concerning operation and maintenance has been
included with this product.
CAUTION: FCC/CSA regulations state that any unauthorized changes
or modications to this equipment may void the user’s
authority to operate it.
CAUTION: To prevent electric shock, match the wide blade of plug to
the wide slot, and fully insert the plug.
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
The Socket-outlet should be installed near the apparatus and be easily
accessible.
Read and follow these instructions
when connecting and using your Public
Information Display:
• Unplug the display if you are not going to use it for an extensive period
of time.
• Unplug the display if you need to clean it with a slightly damp cloth.
The screen many be wiped with a dry cloth when the power is off.
However, never use alcohol, solvents or ammonia-based liquids.
• Consult a service technician if the display does not operate normally
when you have followed the instructions in this manual.
• The casing cover should be opened only by qualied service personnel.
• Keep the display out of direct sunlight and away from stoves or any
other heat sources.
• Remove any object that could fall into the vents or prevent proper
cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry. To avoid electric shock, do not expose it to rain
or excessive moisture.
• If turning off the display by detaching the power cable, wait for 6
seconds before re-attaching the power cable for normal operation.
• To avoid the risk of shock or permanent damage to the set do not
expose the display to rain or excessive moisture.
• When positioning the display, make sure the power plug and outlet are
easily accessible.
• IMPORTANT: Always activate a screen saver program during your
application. If a still image in high contrast remains on the screen for an
extended period of time, it may leave an ‘after-image’ or ‘ghost image’
on the front of the screen. This is a well-known phenomenon that is
caused by the shortcomings inherent in LCD technology. In most cases
the afterimage will disappear gradually over a period of time after the
power has been switched off. Be aware that the after-image symptom
cannot be repaired and is not covered under warranty.
ii
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specied by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15. The batteries (batteries installed) shall not be exposed to excessive
heat such as sunshine, re or the like.
16. An all-pole MAINS SWITCH is used as the disconnect device, the
location on the apparatus and the function of the switch shall be
described, and the switch shall remain readily operable
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
WARNING: Apparatus shall not be exposed to dripping or splashing
and no objects lled with liquids, such as vases, shall be
placed on the apparatus.
WARNING: The batteries (batteries installed) shall not be exposed to
excessive heat such as sunshine, re or the like.
WARNING: The mains plug or appliance coupler is used as the
disconnect device,the disconnect device shall remain
readily operable.
WARNING: To prevent the spread of re, keep candles or other open
ames away from this product at all times.
WARNING: To prevent injury, this apparatus must be securely attached
to the oor/wall in accordance with the installation
instructions.
WARNING: The Class I apparatus shall be connected to a mains socket
outlet with a protective earthing connection.
WARNING
Never place a television set in an unstable location. A television set may
fall, causing serious personal injury or death. Many injuries, particularly to
children, can be avoided by taking simple precautions such as:
• Using cabinets or stands recommended by the manufacturer of the
television set.
• Only using furniture that can safely support the television set.
• Ensuring the television set is not overhanging the edge of the
supporting furniture.
• Not placing the television set on tall furniture (for example, cupboards
or bookcases) without anchoring both the furniture and the television
set to a suitable support.
• Not placing the television set on cloth or other materials that may be
located between the television set and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach
the television set or its controls.
If your existing television set is being retained and relocated, the same
considerations as above should be applied.
CAUTION: These servicing instructions are for use by qualied service
personnel only. To reduce the risk of electric shock,do not
perform any servicing other than that contained in the
operating instructions unless you are qualitied to do so.
CAUTION: Excessive sound pressure from earphones and headphones
can cause hearing loss. Adjustment of the equalizer to
maximum increases the earphone and headphone output
voltage and the sound pressure level. Therefore, to protect
your hearing, adjust the equalizer to an appropriate level.
For UL/CUL application: For use only with UL Listed Wall Mount Bracket
with minimum weight/load: 5.2 Kg
For CB application: Unit without base weight: 5.2 Kg. The equipment and
its associated mounting means still remain secure during the test.(Used
wall mounting kit: 200x200/100x100 mm distance by using M4 screws of
10 mm long plus the thickness of the mounting bracket.
iii
IMPORTANT INFORMATION
If a television is not positioned in a sufciently stable location, it can be
potentially hazardous due to falling. Many injuries, particularly to children,
can be avoided by taking simple precautions such as:
• Using cabinets or stands recommended by the manufacturer of the
television.
• Only using furniture that can safely support the television.
• Ensuring the television is not overhanging the edge of the supporting
furniture.
• Not placing the television on tall furniture(for example, cupboards or
bookcases)without anchoring both the furniture and the television to a
suitable support.
• Not standing the televisions on cloth or other materials placed
between the television and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach
the television or its controls.
EU Declaration of Conformity
This device complies with the requirements set out in the Council
Directive on the Approximation of the Laws of the Member States relating
to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive
(2014/35/EU) and RoHS directive (2011/65/EU).
This product has been tested and found to comply with the harmonized
standards for Information Technology Equipment, these harmonized
standards published under Directives of Ofcial Journal of the European
Union.
Warning:
This equipment is compliant with Class A of EN55032/CISPR 32. In a
residential environment this equipment may cause radio interference.
ESD Warnings
When user close to the monitor may cause the equipment discharge and
reboot to the display of main menu.
Information for EAC
Month and year of
manufacturing
please refer information in Rating label.
Name and location of
manufacturer
ООО “Профтехника”
Адрес: 3-й Проезд Марьиной рощи,
40/1 офис 1. Москва, 127018, Россия
Importer and information Наименование организации: ООО
“Профтехника”
Адрес: 3-й Проезд Марьиной рощи,
40/1 офис 1. Москва, 127018, Россия
Контактное лицо: Наталья Астафьева,
+7 495 640 20 20
nat@profdisplays.ru
Federal Communications Commission (FCC)
Notice (U.S. Only)
Note: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
Changes or modications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when
connecting this display to a computer device.
To prevent damage which may result in re or shock hazard, do not
expose this appliance to rain or excessive moisture.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Envision Peripherals Inc.
490 N McCarthy Blvd, Suite #120
Milpitas, CA 95035
USA
Polish Center for Testing and Certication
Notice
The equipment should draw power from a socket with an attached
protection circuit (a three-prong socket). All equipment that works
together (computer, display, printer, and so on) should have the same
power supply source.
The phasing conductor of the room’s electrical installation should have a
reserve short-circuit protection device in the form of a fuse with a nominal
value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be
removed from the power supply socket, which should be located near the
equipment and easily accessible.
A protection mark “B” conrms that the equipment is in compliance with
the protection usage requirements of standards PN-93/T-42107 and PN-
89/E-06251.
iv
Electric, Magnetic and Electronmagnetic Fields
(“EMF”)
1. We manufacture and sell many products targeted at consumers, which,
like any electronic apparatus, in general have the ability to emit and
receive electromagnetic signals.
2. One of our leading Business Principles is to take all necessary health
and safety measures for our products, to comply with all applicable
legal requirements and to stay well within the EMF standards applicable
at the time of producing the products.
3. We are committed to develop, produce and market products that
cause no adverse health effects.
4. We conrm that if its products are handled properly for their intended
use, they are safe to use according to scientic evidence available today.
5. We play an active role in the development of international EMF and
safety standards, enabling us to anticipate further developments in
standardization for early integration in its products.
Information for U.K. only
WARNING – THIS APPLIANCE MUST BE EARTHED.
Important:
(A)
(B)
This apparatus is supplied with an approved moulded 13A plug. To change
a fuse in this type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved
type.
3. Ret the fuse cover.
If the tted plug is not suitable for your socket outlets, it should be cut off
and an appropriate 3-pin plug tted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug
without a fuse is used, the fuse at the distribution board should not be
greater than 5A.
NOTE: The severed plug must be destroyed to avoid a possible shock
hazard should it be inserted into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance with the following
code:
BLUE – “NEUTRAL” (“N”)
BROWN – “LIVE” (“L”)
GREEN & YELLOW – “EARTH” (“E”)
1. The GREEN & YELLOW wire must be connected to the terminal in
the plug which is marked with the letter “E” or by the Earth symbol or
coloured GREEN or GREEN & YELLOW.
2. The BLUE wire must be connected to the terminal which is marked
with the letter “N” or coloured BLACK.
3. The BROWN wire must be connected to the terminal which marked
with the letter “L” or coloured RED.
Before replacing the plug cover, make certain that the cord grip is clamped
over the sheath of the lead – not simply over the three wires.
v
China RoHS
根据中国大陆《电子电气产品有害物质限制使用标识要求》，以下部分
列出了本产品中可能包含的有害物质的名称和含量。
零部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr
(VI))
多溴
联苯
(PBB)
多溴二
苯醚
(PBDE)
外壳 ○ ○ ○ ○ ○ ○
液晶显示屏 ×○ ○ ○ ○ ○
电路板组件*×○ ○ ○ ○ ○
电源适配器 ×○ ○ ○ ○ ○
电源线/连接线 ×○ ○ ○ ○ ○
遥控器 X ○ ○ ○ ○ ○
本表格依据SJ/T 11364 的规定编制。
*: 电路板组件包括印刷电路板及其构成的零部件，如电阻、
电容、集成电路、连接器等。
O: 表示该有害物质在该部件所有均质材料中的含量均在
GB/T 26572规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超
出GB/T 26572规定的限量要求。
上表中打“×”的部件，应功能需要，部分有害物质含量超出
GB/T 26572规定的限量要求，但符合欧盟RoHS法规要求（属于
豁免部分）。
备注：上表仅做为范例，实际标示时应依照各产品的实际部件及所
含有害物质进行标示。
10 环保使用期限
在产品本体上标示的该标志表示环境保护使用期限为 10 年。
电子信息产品的环境保护使用期限是指电子信息产品中所含的有害
物质不会向外部泄漏或出现突然变异，并且电子信息产品的用户在
使用该电子信息产品时也不会对环境造成严重污染或对人体、财产
带来严重损害的期限。
在环境保护期限中，请按照使用说明书使用本产品。
本环境保护使用不覆盖易损件：电池。
《废弃电子产品回收处理管理条例》提示性说明
为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终
止时，请遵守国家废弃电器电子产品回收处理相关法律规定，将其
交给当地具有国家认可的回收处理资质的厂商进行回收处理。
警告
此为 A级产品。在生活环境中，该产品可能会造成无线电干扰。
在这种情况下，可能需要用户对干扰采取切实可行的措施。
仅适用于非热带气候条件下安全使用 :
汉文仅适用于非热带气候条件下安全使用。
蒙古文
藏文
维文
壮文
Dan hab yungh youq gij dienheiq diuzgen mbouj dwg
diegndat haenx ancienz sawjyungh.
汉文
“注意
如果电池更换不当会有爆炸危险
只能用同样类型或等效类型的电池来更换”
蒙古文
藏文
维文
壮文
“Louzsim
Danghnaeuz denyouz vuenh ndaej mbouj habdangq aiq miz
gij yungyiemj fatseng bauqcaq
Cijndaej yungh gij denyouz doengzyiengh loihhingz roxnaeuz
daengjyauq loihl haenx vuenh”
汉文
“接入本设备的有线网络天线必须与保护接地隔离 ,不
然可能会引起着火等危险 !”
蒙古文
藏文
维文
壮文
“Gij mizsienq vangjloz denhsen ciephaeuj bonj sezbi daeuj
haenx itdingh aeu caeuq gij ciepdieg baujhoh doxliz, mboujne
aiq miz gij yungyiemj dawzfeiz daengj!”
vi
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG
ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING
PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG
STIKKONTAKT ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN
TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT
KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
End-of-Life Disposal
Your new Public Information Display contains materials that can be
recycled and reused. Specialized companies can recycle your product to
increase the amount of reusable materials and to minimize the amount to
be disposed of.
Please nd out about the local regulations on how to dispose of your old
display from your local philips dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance
to local-state and federal regulations. For additional information on
recycling contact www.eia.org (Consumer Education Initiative)
Waste Electrical and Electronie Equipment-
WEEE
Attention users in European Union private households
This marking on the product or on its packaging
illustrates that, under European Directive 2012/19/
EU governing used electrical and electronic appliances,
this product may not be disposed of with normal
household waste. You are responsible for disposal of
this equipment through a designated waste electrical
and electronic equipment collection. To determine
the locations for dropping off such waste electrical
and electronic, contact your local government ofce,
the waste disposal organization that serves your
household or the store at which you purchased the
product.
End of Life Directives-Recycling
Your new Public Information Display contains several
materials that can be recycled for new users.
Please dispose of according to all Local, State, and
Federal laws.
Restriction on Hazardous Substances statement (India)
This product complies with the “E-Waste (Management) Rules, 2016”
CHAPTER V, rule 16, sub-rule (1) . Whereas New Electrical and
Electronic Equipment and their components or consumables or parts or
spares do not contain Lead, Mercury, Cadmium, Hexavalent Chromium,
polybrominated biphenyls and polybrominated diphenyl ethers beyond a
maximum concentration value of 0.1% by weight in homogenous materials
for lead, mercury, hexavalent chromium, polybrominated biphenyls and
polybrominated diphenyl ethers and of 0.01% by weight in homogenous
materials for cadmium. except of exemptions set in Schedule 2 of the Rule.
E-Waste Declaration for India
This symbol on the product or on its packaging
indicates that this product must not be disposed of
with your other household waste. Instead it is your
responsibility to dispose of your waste equipment
by handing it over to a designated collection point
for the recycling of waste electrical and electronic
equipment . The separate collection and recycling
of your waste equipment at the time of disposal
will help to conserve natural resources and ensure
that it is recycled in a manner that protects human
health and the environment. For more information
about E -waste please visit http://www.india.philips.
com/about/sustainability/recycling/index.page
and to know where you can drop off your waste
equipment for recycling in India please contact on
below given contact details.
Helpline number: 1800-425-6396 (Monday to Saturday, 9 a.m. to 5:30 pm)
E-mail: india.callcentre@tpv-tech.com
Batteries
For EU: The crossed-out wheeled bin implies
that used batteries should not be put to the
general household waste! There is a separate
collection system for used batteries, to allow
proper treatment and recycling in accordance with
legislation.
Please contact your local authority for details on
the collection and recycling schemes.
For Switzerland: The used battery is to be returned
to the selling point.
For other non-EU countries: Please contact your
local authority for correct method of disposal of
the used battery.
According to EU directive 2006/66/EC, the battery
can’t be disposed improperly. The battery shall be
separated to collect by local service.
vii
Após o uso, as pilhas
deverão ser entregues ao
estabelecimento comercial ou
e/ou baterias
rede de assistência técnica
autorizada.
Turkey RoHS:
Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur
Ukraine RoHS:
Обладнання відповідає вимогам Технічного регламенту щодо
обмеження використання деяких небезпечних речовин в електричному
та електронному обладнанні, затвердженого постановою Кабінету
Міністрів України від 3 грудня 2008 № 1057
viii
Table Of Contents
1. Unpacking and Installation .......................................................1
1.1. Unpacking .........................................................................................1
1.2. Package Contents ........................................................................ 1
1.3. Installation Notes .........................................................................1
1.4. Mounting on a Wall ....................................................................2
2. Parts and Functions ...................................................................3
2.1. Control Panel ................................................................................. 3
2.2. Input/Output Terminals .............................................................4
2.3. Using the remote sensor and power indicator ..........6
2.4. USB Cover ....................................................................................... 7
2.5. Remote Control ........................................................................... 8
3. Connecting External Equipment.......................................... 10
3.1. Connecting External Equipment (DVD/VCR/
VCD) ...............................................................................................10
3.2. Connecting a PC ....................................................................... 10
3.3. Connecting Audio Equipment ...........................................11
3.4. Connecting Multiple Displays in a Daisy-chain
Conguration .............................................................................. 11
3.5. IR connection .............................................................................. 12
3.6. IR Pass-through Connection ...............................................12
4. Operation ................................................................................. 13
4.1. Play multimedia les from USB device .........................13
5. OSD Menu ............................................................................... 14
5.1. Navigating the OSD Menu ..................................................14
5.2. OSD Menu Overview ...........................................................14
6. Supported Media Formats .................................................... 19
7. Input Mode ............................................................................... 20
8. Cleaning and Troubleshooting .............................................. 21
8.1. Cleaning ..........................................................................................21
8.2. Troubleshooting .........................................................................22
9. Technical Specications ......................................................... 24
1
1. Unpacking and Installation
1.1. Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2. Package Contents
Please verify that you received the following items with your package content:
• LCD display
• Quick start guide
• Remote control with AAA batteries
• Power cord
• RS232 cable
• RS232 daisy chain cable
• IR sensor cable
• USB cover and screw x1 * The supplied power cord varies depending on destination.
Quick start guide Remote Control
and AAA Batteries
FORMAT
SOURCE
INFOLIST
OPTIONSADJUST
VOL
NORMAL ID
ID SET ENTER
Power Cord RS232 Daisy Chain Cable RS232 Cable
IR Sensor Cable USB Cover Screw
LCD display
* Items may differ in different locations
* Display design and accessories may differ from the images shown.
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies with the
safety regulations of the particular country (Type H05W-F, 2G or 3G, 0.75 or 1 mm2 should be used).
• Keep the packaging materials appropriately after unpacking the product.
1.3. Installation Notes
• Only use the power cable provided with this product. If an extension cord is required, please consult your service agent.
• The product should be installed on a at surface, or the product may tip over. Leave a space between the rear of the product and the wall for proper
ventilation. Do not install the product in a kitchen, bathroom or a place exposed to moisture, failure to do so may shorten the life of the internal
parts.
• Do not install the product where it is 3000m and higher in altitude. Failure to do so may result in malfunctions.
2
1.4. Mounting on a Wall
To mount this display on a wall, a standard wall-mounting kit (commercially available) is required. It is recommended that you use a mounting interface that
complied with TUV-GS and /or UL1678 standard in North America.
Protective Sheet
VESA Grid
Table
1. Spread a protective sheet on a at surface, which is wrapped around the display when it was packed, beneath the screen surface to facilitate your
operation without scratching the screen.
2. Ensure you have all accessories necessary for all types of mounting (wall mount, ceiling mount, table stand, etc).
3. Follow the instructions that came with the base mounting kit. Failure to follow the correct mounting procedures could result in damage to the
equipment, or injury to the user or installer. The product warranty does not cover the damage caused by improper installation.
4. For the wall-mounting kit, use the M4 mounting screws (with a length 10 mm longer than the thickness of the mounting bracket) and tighten them
securely
5. Weight of the unit without base = 5.2 kg. The equipment and its associated mounting facilities still remain secure during the test. Use only the UL
listed Wall Mount Bracket with a minimum weight/load of 5.2 kg.
6. Portrait orientation is not allowed.
1.4.1. VESA Grid
32BDL3010Q 100(H) x 100(V) mm
200(H) x 200(V) mm
Caution:
To prevent the display from falling:
• For wall or ceiling installation, we recommend that you install the display with metal brackets which are commercially available. For detailed instructions
about the installation, refer to the guide provided with the bracket.
• To prevent the display from falling in case of earthquake or other natural
disaster, please consult the manufacturer of the bracket for the mounting location.
Ventilation Requirements for enclosure locating
Leave a space of 100 mm at the top, rear, right and left of the display for ventilation.
100 mm 100 mm
100 mm
100 mm
3
2. Parts and Functions
2.1. Control Panel
MUTE INPUT MENU
1 2 3 4 5 6 7 8
9
1 [ ] button
Turn the display On or turn the display to standby mode.
2 [MUTE] button
Mute the sound or reactivate sound.
3 [INPUT] button
Select an input source.
4 [ ] button
• Increase the audio output level
• Enter into the submenu while OSD menu is on
5 [ ] button
• Decrease the audio output level
• Back to previous menu while OSD menu is on
6 [ ] button
• Move the selected item one level up while the OSD menu is
On
• Increase the adjustment.
7 [ ] button
• Move the selected item one level down while the OSD menu is
On.
• Decrease the adjustment.
8 [MENU] button
Return to the previous menu while the OSD menu is On. This
button can also be used to activate the OSD menu when the OSD
menu is Off.
9
Remote control sensor and power status indicator
• Receives command signals from the remote control.
• Indicates the operating status of the display without OPS:
-Lights green when the display is turned On
-Lights red when the display is in the standby mode
-When {SCHEDULE} is enabled, the light blinks green and red
-If the light blinks red, it indicates that a failure has been
detected
-Lights off when the main power of the display is turned off
* Use an IR sensor cable for better remote control performance.
(Please refer to the instructions of 3.5)
4
2.2. Input/Output Terminals
DVI-I HDMI 2 IN HDMI 1 IN
RS232 OUT
RS232 IN
IR-IN
IR-OUT
AUDIO OUT
PC LINE IN
RJ45
USB 2.0
R
L
6
78
9
10
11
12
13
14
1
3 4 5
2
1 AC IN
AC power input from the wall outlet.
2 MAIN POWER SWITCH
Switch the main power between on and off.
3 DVI-I IN
DVI/VGA video input.
4 HDMI2 IN / 5 HDMI1 IN
HDMI video/audio input.
6 RS232 IN / 7 RS232 OUT
RS232 network input / output for the loop-through function.
8 IR IN / 9 IR OUT
IR signal input / output for the loop-through function.
NOTES:
• This remote control sensor of this display will stop working if the
jack [IR IN] is connected.
• To remotely control your A/V device via this display, refer to page
12 for IR Pass Through connection.
10 AUDIO OUT
Audio output to external AV device.
11 PC LINE IN
Audio input for VGA source (3.5mm stereo phone).
12 RJ-45
LAN control function for using the remote control signal from the
control center.
13 USB 2.0 PORT
Connect your USB storage device and service port.
14 SECURITY LOCK
Used for protecting the product from stealing.
5
2.2.1. Inserting the batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace the batteries:
1. Press and then slide the cover to open it.
2. Insert the batteries with the correct polarity (+) and (-).
3. Replace the cover.
Caution:
Incorrect use of batteries may cause leakage or explosion. Be sure to follow the instructions below:
• Insert “AAA” batteries with the correct polarity (+ and -).
• Do not mix battery types.
• Do not use a new battery with a used one together. Otherwise, it may cause leakage or shorten the life of the batteries.
• Remove the dead batteries immediately to avoid battery leakage in the battery compartment. Do not touch exposed battery acid, as it may cause
injury to your skin.
NOTE: Remove the batteries from the battery compartment when not using for an extended period of time.
2.2.2. Handling the remote control
• Do not drop or apply shock to the remote control.
• Do not allow any liquid to get inside the remote control. If water has entered the remote control, wipe the remote control with a dry cloth
immediately.
• Do not place the remote control near heat and steam sources.
• Do not attempt to disassemble the remote control, unless you need to place batteries in the remote control.
2.2.3. Operating range of the remote control
Point the top front of the remote control at the remote sensor on the display when you press the
buttons.
Use the remote control within a distance of less than 6m (pull the lens down and use the remote
control from the front) /19ft from the display’s sensor, and a horizontal and vertical angle of less
than 20 degrees.
NOTE: The remote control may not function properly when the remote control sensor on the
display is under direct sunlight or strong illumination, or when there is an object between
the remote control and the remote sensor of the display.
2020
6
2.3. Using the remote sensor and power indicator
1. Push down the lens to have better remote control performance and make it easy to observe the power status.
2. Pull up the lens before mounting the display for video wall application.
3. Pull/push the lens until a click sound is heard.
Push right to collapse the lens Push left to expand the lens
7
2.4. USB Cover
• Use the USB cover and screws to cover the USB stick and Micro SD card.
USB
RJ45
USB 2.0 USB
• Maximum USB stick size recommended:
USB: 20(W)x10(H)x60(L) mm
L
H
W
8
2.5. Remote Control
2.5.1. General functions
1
2
3
4
5
6
7
8
10
9
12
14
15
11
13
16
1 [ ] POWER button
Turns the power On/Off.
2 [PLAY] buttons
Control playback of media les.
3 [ ] SOURCE button
Select an input source.
4 [ ] HOME button
Access the OSD menu.
5 [ ] LIST button
No function.
6 [ ][ ][ ][ ]NAVIGATION buttons
Navigate through the menus and select an item.
7 [ ] button
Conrm an entry or selection.
8 [ ] ADJUST button
Go to Auto Adjust OSD for VGA only.
9 [ ] MUTE button
Sound mute on or off.
10 [ ] [ ] [ ] [ ] COLOR buttons
No functions.
11 [Number/ ID SET/ ENTER] button
Enter text for network setting.
Press to set the display ID. Refer to 2.5.2. ID Remote Control for
more detail.
12 [ ] FORMAT button
Change the picture format.
13 [ ] BACK button
Return to the previous page or exit from the previous function.
14 [ ] INFO button
Display information about the current input signal.
15 [ ] OPTIONS button
No functions.
16 [ ] [ ] VOLUME button
Adjust volume level.
9
2.5.2. ID Remote Control
Set remote control ID number when using several displays.
Press the [ID] button and the red LED blinks twice.
1. Press the [ID SET] button for more than 1 second to enter the ID
mode. The red LED lights up.
Press the [ID SET] button again to exit from the ID mode. The red
LED lights off.
Press the digit numbers [0] ~ [9] to select the display to be controlled.
For example: press [0] and [1] for display No.1, press [1] and [1] for
display No.11.
The available numbers are [01] ~ [255].
2. If no button is pressed within 10 seconds, it will exit from the ID
mode.
3. If a wrong button is pressed, wait for 1 second until the red LED
lights off and then turns on again, then press the correct digits.
4. Press [ENTER] button to conrm your selection. The red LED blinks
twice and then lights off.
NOTE:
• Press the [NORMAL] button. The green LED blinks twice, indicating
that the display is under normal operation.
• It is necessary to set up the ID number for each display before
selecting its ID number.
10
3. Connecting External Equipment
3.1. Connecting External Equipment (DVD/VCR/VCD)
3.1.1. Using HDMI video input
DVD / VCR / VCD
HDMI 2 IN HDMI 1 IN
HDMI Out
[HDMI IN]
3.2. Connecting a PC
3.2.1. Using DVI input
PC
DVI Out
[DVI IN]
DVI-I
HDMI 4 IN HDMI 3 IN HDMI 2 IN HDMI 1 IN
[AUDIO IN] Audio Out
RS232 OUT
RS232 IN
IR-IN
IR-OUT
AUDIO OUT
PC LINE IN
RJ45
3.2.2. Using HDMI input
PC
HDMI 2 IN HDMI 1 IN
[HDMI IN]
HDMI Out
11
3.3. Connecting Audio Equipment
3.3.1. Connecting an external audio device
Stereo Amplifier
[AUDIO OUT] Audio In
AUDIO OUT
R
L
3.4. Connecting Multiple Displays in a Daisy-chain Configuration
You can interconnect multiple displays to create a daisy-chain conguration for applications such as a menu board.
3.4.1. Display control connection
Connect the [RS232 OUT] connector of DISPLAY 1 to the [RS232 IN] connector of DISPLAY 2.
DISPLAY 1
PC
DISPLAY 2
[RS-232C IN]
[RS-232C]
[RS-232C OUT] [RS-232C IN]
12
3.5. IR connection
[IR IN]
External
IR Receiver
[IR IN]
[IR OUT]
DISPLAY 1 DISPLAY 2
DISPLAY 1 DISPLAY 2
[RS-232C OUT] [RS-232C IN]
NOTES:
1. The remote control sensor of this display will stop working if the [IR IN] is connected.
2. IR loop through connection can support up to 9 displays.
3. IR in daisy chain via RS232 connection can support up to 9 displays.
3.6. IR Pass-through Connection
DVD / VCR / VCD
(DVD / VCR / VCD)
Remote Control
[IR OUT]
[IR IN]
13
4. Operation
NOTE: The control button described in this section is mainly on the
remote control unless specied otherwise.
4.1. Play multimedia files from USB device
1. Connect your USB device to the USB port on the display.
USB
RS232 OUT
RS232 IN
IR-IN
IR-OUT
AUDIO OUT
PC LINE IN
RJ45
USB 2.0
R
L
2. Press [ ] SOURCE button, choose USB, and press [ ]
button.
VGA
DVI-I
HDMI 1
HDMI 2
USB
3. The connected USB device is detected automatically for all its
playable les, which will be automatically sorted into 3 types:
Photo, Music, , and Movie .
USB 2.0
MUSIC MOVIEPHOTO
4. Press [ ] or [ ] button to choose the item. Press [ ] button
to enter its play list.
5. Press [ ], [ ], [ ] or [ ] button to choose the le you want. Press
[ ]or [ ] button to start playing.
6. Follow the on-screen instruction to control the play option.
7. Press [PLAY] buttons ( ) to control playing.
1 / 2
Return aaa1
xxx1 xxx2 xxx3 123
aaa2 aaa3
8. Press [ ], [ ], [ ] or [ ] button to choose “Return" item then
press [ ] button to go up to the top layer in the screen.
14
5. OSD Menu
An overview of the On-Screen Display (OSD) structure is shown
below. You can use it as a reference for further adjustment of your
display.
5.1. Navigating the OSD Menu
5.1.1. Navigating the OSD menu using the
remote control
FORMAT
SOURCE
INFOLIST
OPTIONSADJUST
1. Press [ ] button on the remote control to display the OSD menu.
2. Press [ ] or [ ] button to select the item to adjust.
3. Press [OK] or [ ] button to enter the submenu.
4. In the submenu, press [ ] or [ ] button to toggle between items,
press [ ] or [ ] button to adjust the settings. If there is a
submenu, press [OK] or [ ] button to enter the submenu.
5. Press [ ] button to return to the previous menu, or press [ ]
button to exit from the OSD menu.
5.1.2. Navigating the OSD menu using the
display’s control buttons
1. Press [MENU] button to display the OSD menu.
2. Press [ ] or [ ] button to select the item to adjust.
3. Press [ ] button to enter the submenu.
4. In the submenu, press [ ] or [ ] button to toggle between items,
press [ ] or [ ] button to adjust the settings. If there is a submenu,
press [ ] button to enter the submenu.
5. Press [MENU] button to return to the previous menu, or keep
pressing [MENU] button to exit from the OSD menu.
5.2. OSD Menu Overview
5.2.1. Picture
PICTURE
AUDIO
TILING
NETWORK
OPTION
Picture Mode
Brightness
Contrast
Sharpness
Backlight
Tint
Color
Noise Reduction
Gamma
Color Temperature
Zoom Mode
Scan Mode
50
50
50
100
50
50
0
Low
2.2
Full
Standard
Picture Mode
Select a predened picture setting.
Brightness
Adjust the brightness of this display’s backlight.
Contrast
Adjust the contrast ratio for the input signal.
Sharpness
This function is digitally capable to keep a distinct image at all times.
Adjust the sharpness of the picture for each picture mode.
Backlight
Adjust the brightness of this display’s backlight.
NOTE: sRGB picture mode is standard and cannot be changed.
Tint (Hue)
Adjust tint of the screen.
Press + button to make the tone color greenish.
Press - button to make the tone color purplish.
NOTE: for VIDEO mode only.
Color (Saturation)
Adjust color saturation.
Press + button to increase color depth.
Press - button to decrease color depth.
NOTE: for VIDEO mode only
Noise Reduction
Reduce picture noise.
Gamma
Adjust gamma. It refers to the brightness performance curve of signal
input. Select from {Native} / {2.2} / {2.4} / {S gamma} / {D-image}.
NOTE: sRGB picture mode is standard and cannot be changed.
Color Temperature
Adjust color tone.
The image becomes reddish as the color temperature decreases, and
becomes bluish as the color temperature increases.
15
Zoom mode
VGA/DVI-I/HDMI1/HDMI2: {Full} / {4:3} / {Real} / {16:9}.
USB: {Full} / {4:3} / {16:9}
Zoom Mode will be “Full” when tiling.
Full
This mode restores the correct proportions
of pictures transmitted in 16:9 using the full
screen display.
4:3
The picture is reproduced in 4:3 format and
a black band is displayed on either side of the
picture.
Real
This mode displays the image pixel-by-pixel
on screen without scaling the original image
size.
16:9
The picture is reproduced in 16:9 format and
a black band at the top and bottom.
Scan mode
Change the display area of the image.
Picture reset
Reset all your picture settings to the factory defaults.
Select “Ye s ” and press “SET” button to restore to the factory preset
data.
Press “EXIT” button to cancel and return to the previous menu.
5.2.2. Audio
0
50
50
20
100
0
Off
Off
Balance
Treble
Bass
Volume
Maximum Volume
Minimum Volume
Mute
Audio Out Sync
Audio reset
PICTURE
AUDIO
TILING
NETWORK
OPTION
Balance
Adjust to emphasize left or right audio output balance.
Treble
Adjust to increase or decrease higher-pitched sounds.
Bass
Adjust to increase or decrease lower-pitched sounds.
Volume
Adjust the volume.
Maximum volume
Adjust your own limitation for the maximum volume setting. This stops
the volume at the sound level you set.
Minimum volume
Adjust your own limitation for the minimum volume setting.
Mute
Turn the mute function on/off.
Audio Out Sync
Enable/disable the audio out volume.
Audio reset
Reset all settings in the Audio menu to factory preset values.
5.2.3. Tiling
1
1
1
3
3
2
1
Off
Off
PICTURE
AUDIO
TILING
NETWORK
OPTION
Enable
H monitors
V monitors
Position
Frame comp.
Frame comp. Top
Frame comp. Bottom
Frame comp. Left
Frame comp. Right
Create a single large-screen matrix (video wall) that consists of up
to 225 sets of display (up to 15 sets in vertical side and 15 sets in
horizontal side).
Enable
Enable or disable the Tiling function. If {On} is selected, the display will
apply the settings in {H monitors}, {V monitors}, {Position}, and
{Frame comp.}.
H monitors
Set how many displays in horizontal side.
V monitors
Set how many displays in vertical side.
Position
Set the position of this display in the screen matrix.
Example: 2 x 2 screen matrix (4 displays)
H monitors = 2 displays
V monitors = 2 displays
1 2
3 4
H monitors
V monitors
Position
16
Example: 5 x 5 screen matrix (25 displays)
H monitors = 5 displays
V monitors = 5 displays
1 2
6 7
3 4
8 9
5
10
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
H monitors
V monitors
Position
Frame comp.
Turn the frame compensation function On or Off. If you select {On}, the
display will adjust the image to compensate for the width of the display
bezels in order to accurately display the image.
{On}
{Off}
Frame comp. Top
Adjust the top frame compensation.
Frame comp. Bottom
Adjust the bottom frame compensation.
Frame comp. Left
Adjust the left frame compensation.
Frame comp. Right
Adjust the right frame compensation.
5.2.4. Network
Off
. . .
. . .
. . .
PICTURE
AUDIO
TILING
NETWORK
OPTION
DHCP
IP address
Netmask
Gateway
Set
DHCP
Select how this display should assign address to the network resource.
(On: DHCP & Auto IP, Off: Static IP). If DHCP is set to On, the device
will request and be assigned an address every time it is booted up.
Otherwise, you need to ask your network administrator for the
appropriate IP settings.
IP address/Netmask/Gateway/Set
Enter the IP address/Netmask/Gateway/Set.
5.2.5. Option
English
On
On
On
PICTURE
AUDIO
TILING
NETWORK
OPTION
Language
Auto signal detection
Date and Time
Schedule
HDMI with One Wire
Power LED light
Logo
Monitor ID
Network control port
Boot on source
Monitor info
Language
Set OSD menu language.
Auto signal detection
This function allows the system to detect and display the available signal
sources automatically.
• {Off} - Once an input is connected, it can only be selected manually.
If the selected input has signal, set the system to display the image
automatically according to the search order of each option.
The options are: {Auto} / {Failover}
• {Auto}: VGA-> DVI-I-> HDMI1-> HDMI2->USB.
• {Failover}
- Failover 1: User-dened setting. Default:HDMI 1.
- Failover 2: User-dened setting. Default:HDMI 1.
- Failover 3: User-dened setting. Default:HDMI 1.
- Failover 4: User-dened setting. Default:HDMI 1.
- Failover 5: User-dened setting. Default:HDMI 1.
- Failover 6: User-dened setting. Default:HDMI 1.
17
- Failover 7: User-dened setting. Default:HDMI 1.
Date and time
Set the current date and time for the display’s internal clock.
NOTES:
The denition and behavior of the Daylight saving time:
The current implementation of daylight saving is a reminder tool for the
user who doesn’t know how to adjust the clock of daylight saving.
It does not adjust the real time clock automatically. The problem is that
there are no standard rules on when to adjust the clock dened by
region or country. To solve this problem, the user must be able to set
the daylight saving start/end date. When daylight saving correction is on
(user selectable) then the real time clock should be adjusted at the time
set of the daylight saving on/off date. At the start date of daylight saving,
the clock should be adjusted 1 hour forward at 2 o’clock. At the end
date of daylight saving, the clock should be adjusted 1 hour backward at
2 o’clock.
The existing daylight on/off menu should be replaced by the following
menu structure:
The menu item {Daylight saving} opens the submenu that contains the
following items:
• Menu item {Daylight saving start date} Selection item {1st, 2nd, 3rd,
4th, last} Sunday of selection item {1-12 month}
• Menu item {Daylight saving stop date} Selection item {1st, 2nd, 3rd,
4th, last} Sunday of selection item {1-12 month}
• Menu item {Correction time} Selection item {0.5, 1.0, 1.5, 2.0} hour
• Menu item {Daylight saving} Selection item {on, off}
When “daylight saving” is “on”, the real time clock will be adjusted
automatically at the daylight saving time (e.g. April 5, 2015, 02.00 o’clock:
time will be set 1 hour later or October 25, 2015, 02.00 o’clock: time
will be set 1 hour earlier).
Schedule
This function allows you to program up to 7 (seven) different scheduled
time intervals for the display to activate.
You can select:
• The time for the display to turn On and Off.
• The days in a week for the display to activate.
• Which input source the display will use for each scheduled
activation period.
NOTE: It is recommended that you set up the current date and time
in the {Date and time} menu before using this function.
1. Press [OK] or [ ] button to enter the submenu.
Schedule 1
Schedule 2
Schedule 3
Schedule 4
Schedule 5
Schedule 6
Schedule 7
Schedule
2. Press [] or [] button to select a schedule item (item number 1 ~ 7),
and press [OK] or [ ] button to enter the submenu.
Schedule 1
Schedule 2
Schedule 3
Schedule 4
Schedule 5
Schedule 6
Schedule 7
Schedule
Status
Source
On Time
Off Time
Repeat modes
On
HDMI1
-- : --
-- : --
• {Status} - Press [ ] or [ ] button to select the status On or Off.
• {Source} - Press [ ] or [ ] button to select the input source.
• {On Time} - Press [ ] or [ ] button to adjust and the display will
turn on at the specied time.
• {Off Time} - Press [ ] or [ ] button to adjust and the display will
turn off at the specied time.
Leave hour and minute options empty if you do not want to use
the function of power-on or power-off schedule.
• {Repeat modes} -Press [ ] button to select which day in a week
this schedule item will take effect, and then press the [OK] button.
3. For additional schedule settings, press [ ], then repeat the steps
above. A check mark in the box next to the number of the schedule
item indicates that the selected schedule is in effect.
NOTES:
• If the schedules overlap, the scheduled power-on time takes priority
over scheduled power-off time.
• If there are two schedule items programmed for the same time, the
highest numbered schedule takes priority. For example, if schedule
items #1 and #2 both set the display to power on at 7:00 AM and
off at 5:00 PM, then only schedule item # 2 will take effect.
HDMI with One Wire
CEC control.
• {Off} - Disable CEC.(Default)
• {On} - Enable CEC.
Power LED Light
Select {Off} to turn off the indicator.
Logo
Select {Off} and the display will not display the logo when you
switch on.
Monitor ID
Set ID number for controlling the display via the RS232C connection.
Each display must have a unique ID number when multiple sets of
display are connected. Monitor ID number range is between 1 to 255.
Monitor Id
Monitor Id
Monitor group
1
1
• {Monitor group}
• {1-255} – {Monitor group} are supported. The default setting is
1.
18
Network control port.
Select from: {RS232} / {LAN}.
Boot on source
Select the input source when booting.
Input: select the input source when booting.
No failover function, the system will keep the source even the source
has no signal input.
Monitor information
Show information about your display, including Input source, Resolution,
Model name, SW version, Serial number and MAC address.
Power Save
Mode 1 [TCP off, auto off]
Mode 2 [TCP on, auto on/off]
Power save modes
Mode 1: DC off -> Power off. LED: Red.
Power Save -> Power off, LED: Red
Mode 2: DC off -> Power off, LED: Red.
Power Save -> Power Saving. LED: Orange. Can be wake up.
RCU Power
Button Off No Signal
Mode 1 [TCP off, auto off] DC OFF DC OFF
Mode 2 [TCP on, auto on/off] DC OFF When signal is back,
system wakes up
Firmware update
Update scalar rmware by USB.
Factory Reset
Reset all your customized settings to the factory default values.
Option Reset
Reset all settings in the option menu to the factory preset values.
19
6. Supported Media Formats
USB Multimedia Formats
Video format
Video Codec Resolution Bit Rate
MPEG1/2 1080P@30fps 40Mbps
H.264 1080P@30fps 50Mbps
WMV3 1080P@30fps 40Mbps
Motion JPEG 640x480@30fps 40Mbps
Audio format
Audio Codec Sampling Rate: Channel Bit Rate
MPEG1/2 Layer1 16KHz~48KHz Up to 2 32Kbps~448Kbps
MPEG1/2 Layer2 16KHz~48KHz Up to 2 8Kbps~384Kbps
MPEG1/2 Layer3 16KHz~48KHz Up to 2 8Kbps~320Kbps
AAC, HEAAC 8KHz~48KHz Up to 5.1 32Kbps~448Kbps
WMA 8KHz~48KHz Up to 2 128Kbps~320Kbps
Photo format
Image Photo Resolution
JPEG Base-line 15360x8640
(1920x8 x 1080x8)
Progressive 1024x768
PNG non-interlace 9600x6400
interlace 1200x800
BMP 9600x6400
NOTES:
• Sound or video may not work if the contents have a standard bit rate/frame rate above the compatible Frame/sec listed in the table above.
• Video content with a Bit rate or Frame rate larger than the rate specied in the table above can cause choppy video during playback.
20
7. Input Mode
Timing support:
Item Resolution H.Freq. (KHz) V.Freq. (Hz)
1 720×400 @70Hz DOS 31.469 70.087
2 640×480 @60Hz DMT 31.469 59.94
3 640×480 @67Hz MAC 35 66.667
4 640×480 @72Hz DMT 37.861 72.809
5 640×480 @75Hz DMT 37.5 75
6 800×600 @56Hz DMT 35.156 56.25
7 800×600 @60Hz DMT 37.879 60.317
8 800×600 @72Hz DMT 48.077 72.188
9 800×600 @75Hz DMT 46.875 75
10 832×624 @75Hz MAC 49.725 74.5
11 1024×768 @60Hz DMT 48.363 60.004
12 1024×768 @70Hz DMT 56.476 70.069
13 1024×768 @75Hz DMT 60.023 75.029
14 1152×864 @75Hz DMT 67.5 75
15 1152×870 @75Hz MAC 68.681 75.062
16 1280×720 @60Hz CVT16:9 44.772 59.855
17 1280x800 @60Hz CVT16:10 49.702 59.81
18 1280×1024 @60Hz DMT 63.981 60.02
19 1440×900 @60Hz CVT16:10 R 55.469 59.901
20 1440×900 @60Hz CVT16:10 55.935 59.887
21 1600×1200 @60Hz CVT16:9 75 60
22 1680×1050 @60Hz CVT16:9 R 64.674 59.883
23 1680×1050 @60Hz CVT16:9 65.29 59.954
24 1920×1080 @60Hz CVT-RB / XBOX360 66.7 60
25 1920×1080 @60Hz DMT-RB 67.5 60
26 480i@60Hz 15.734 59.94
27 480P@60Hz 31.469 59.94
28 720P@60Hz 44.955 59.94
29 1080I@60Hz 33.716 59.94
30 1080P@60Hz 67.433 59.94
31 576i@50Hz 15.625 50
32 576P@50Hz 31.25 50
33 720P@50Hz 37.5 50
34 1080I@50Hz 28.125 50.08
35 1080P@50Hz 56.25 50
• The PC text quality is optimum in FHD mode (1920 x 1080, 60Hz).
• Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows).
• Check your PC instruction book for information about connecting your PC to a display.
• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In some cases, abnormal signals (such as
stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the [INPUT] button to enter the
video mode. Also, make sure that the PC is connected.
• When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
• The display settings table complies to the IBM/VESA standards, and based on the analog input.
• The DVI support mode is regarded as same to the PC support mode.
• The best timing for the vertical frequency to each mode is 60Hz.
21
8. Cleaning and Troubleshooting
8.1. Cleaning
Caution When Using the Display
• Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high
temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too
close. Placing any object near the top of the display could also result in heat related damage to the object as well as the display itself.
• Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus cause re
or electric shock.
• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure.
Front Panel Cleaning Instructions
• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a soft, lint-free cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess liquid. Wipe the surface of
the display to remove dirt. Then use a dry cloth of the same type to dry.
• Do not scratch or hit the surface of the panel with ngers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners.
Cabinet Cleaning Instructions
• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.
• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove as much moisture as possible. Wipe
the cabinet. Use another dry cloth to wipe over until the surface is dry.
• Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside the unit, operating
problems, electrical and shock hazards may result.
• Do not scratch or hit the cabinet with ngers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.
• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
22
8.2. Troubleshooting
Symptom Possible Cause Remedy
No picture is displayed 1. The power cord is disconnected.
2. The main power switch on the back of the
display is not switched on.
3. The selected input has no connection.
4. The display is in the standby mode.
1. Plug in the power cord.
2. Make sure that the power switch is switched
on.
3. Connect a signal connection to the display.
Interference displayed on the display or an
audible noise is heard
Caused by surrounding electrical appliances or
uorescent lights.
Move the display to another location to see if the
interference is reduced.
Color is abnormal The signal cable is not connected properly. Make sure that the signal cable is attached rmly
to the back of the display.
Picture is distorted with abnormal patterns 1. The signal cable is not connected properly.
2. The input signal is beyond the capabilities of
the display.
1. Make sure that the signal cable is attached
rmly.
2. Check the video signal source to see if it
is beyond the range of the display. Please
verify its specications with this display’s
specication section.
Display image doesn’t ll up the full size of the
screen
1. The zoom mode is not set correctly.
2. Scan Mode may be set incorrectly to
underscan.
3. If the image exceeds the screen size, Scan
Mode may need to be set to Underscan.
Use the Zoom mode or Custom zoom function
in the Screen menu to ne tune display geometry
and time frequency parameter.
Can hear sound, but no picture Source signal cable is connected improperly Make sure that both video inputs and sound
inputs are connected correctly.
Can see picture but no sound is heard 1. Source signal cable is connected improperly.
2. Volume is turned all the way down.
3. {Mute} is turned on.
4. No external speaker is connected.
1. Make sure that both video inputs and sound
inputs are connected correctly.
2. Press [ ] or [ ] button to hear sound.
3. Switch MUTE off by using the [ ] button.
4. Connect external speakers and adjust the
volume to a suitable level.
Some picture elements do not light up Some pixels of the display are off. This display is designed using an extremely high
level of precision technology: however, sometimes
some pixels of the display may not display. This is
not a malfunction.
After-Images can still be seen on the display
after the display is powered off. (Examples
of still pictures include logos, video games,
computer images, and images displayed in 4:3
normal mode)
A still picture is displayed for an over extended
period of time
Do not allow a still image to be displayed for
an extended period of time as this can cause a
permanent after-image to remain on the display.
23
How to setup the settings in the menu to
control all the monitors at the same time and
individually via RC?
Daisy chained by RS232 and no IR cable 1. The rst display sets as “Primary” on OSD
(Advanced option/IR control item), others set as
“Secondary”.
2. The setup OSD will show on top left side of
the display. (Toggle MENU will show again if it
disappears)
3. Default setting: ID NO: 0, GP NO: 0, this setting
can control all displays by IR.
The “+”, “-” can change “ID NO” to control
signal display by “Monitor ID”.
The “UP”, “DOWN” can change “GP NO” to
control multi-display by “Group ID”.
*The rst display is always controlled by IR.
How does the RC work? Daisy chain : no connection of RS232 and IR
cable
No setting is required. Connect with IR cables
and control by IR.
*This may cause out-of-synchronizm
phenomenon. It is suggested to use the above
settings with RS-232 cable.
24
9. Technical Specifications
Display:
Item Specications
Screen Size (Active Area) 800 mm / 31.5 inch
Aspect Ratio 16:9
Number of pixels 1920 (H) x 1080 (V)
Pixel pitch 0.36375 (H) x 0.36375 (V) [mm]
Displayable colors 8 bit, 16.7M colors
Brightness (typical) 350 cd/m2
Contrast ratio (typical) 1200:1
Viewing angle 178 degrees
In/Out Terminals:
Item Specications
Speaker Output Internal Speakers 10W (L) + 10W (R) [RMS]/8Ω
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output RCA R/L x 1 0.5V [rms] (Normal) / 2 Channel (L+R)
Audio Input 3.5mm phone jack x 1 0.5V [rms] (Normal) / 2 Channel (L+R)
RS232C 2.5mm Phone jack x 2 RS232C in/RS232C out
RJ-45 RJ-45 Jack x 1 (8 pin) 10/100 LAN Port
HDMI Input HDMI Jack x 2
(Type A) (19 pin)
Digital RGB: TMDS (Video + Audio)
MAX:
Video - 720p, 1080p, 1920 x 1080/60 Hz
Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
DVI-I Input DVI-I Jack Digital RGB: TMDS (Video)
IR Input/Output 3.5mm x 2 IR pass through or IR daisy chain
USB Input USB x 1 (Type A) USB 2.0, Multimedia play and service port
General:
Item Specications
Power Input 100 - 240V~, 50-60Hz, 1.5A
Power Consumption (Max) 75 W
Power Consumption (typ.) 50 W
Power Consumption (Standby & Off) <0.5 W
Dimensions [W x H x D] 726.50 x 425.40 x 67.60 mm
Weight 5.2 0Kg
Gross Weight 7.70 Kg
Energy Efciency Class B
Visible Screen Size 800 mm / 31.5 inch
On Mode Power Consumption (W) 50 W
Annual Energy Consumption (kWh) 73 kWh
Standby Power Consumption (W) 0.50 W
Off Mode Power Consumption (W) 0.30 W
Display Resolution (Pixels) 1920 x 1080
25
Environmental Condition:
Item Specications
Temperature Operational 0 ~ 35°C
Storage -20 ~ 60°C
Humidity Operational 20 ~ 80% RH (No condensation)
Storage 5 ~ 95% RH (No condensation)
Altitude Operational 0 ~ 3,000 m
Storage / Shipment 0 ~ 9,000 m
2019 © Koninklijke Philips N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license from
Koninklijke Philips N.V.
Specications are subject to change without notice.