Table of Contents
- 1. Unpacking and Installation
- 2. Parts and Functions
- 3. Connecting External Equipment
- 4. Operation
- 5. OSD Menu
- 6. Supported Media Formats
- 7. Input Mode
- 8. Pixel Defect Policy
- 9. Cleaning and Troubleshooting
- 10. Warranty Statement
- 11. Technical Specifications
Philips 55BDL3017P/00 User Manual
Displayed below is the user manual for 55BDL3017P/00 by Philips which is a product in the Signage Displays category. This manual has pages.
Related Manuals
Professional
Display Solutions
P Line
43BDL3017P/50BDL3017P/
55BDL3017P
User Manual (English)
www.philips.com/welcome
43BDL3017P/50BDL3017P/55BDL3017P
ii
Safety Instructions
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than those specied in this documentation may
result in exposure to shock, electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and using your display:
Operation:
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Keep the display away from oil, otherwise the plastic cover may be damaged.
• It is recommended to set the display up in the well-ventilated place.
• Ultra-violet ray lter is necessary of outdoor operation.
• If the product will be used in extreme conditions such as high temperature, humidity, display patterns or operation time
etc... It is strongly recommended to contact Philips for Application engineering advice. Otherwise, its reliability and function
may not be guaranteed. Extreme conditions are commonly found at Airports, Transit Stations, Banks, Stock market, and
Controlling systems.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• When turning o the display by detaching the power cord, wait 6 seconds before re-attaching the power cord for normal
operation.
• Ensure the use of an approved power cord provided by Philips at all times. If your power cord is missing, please contact your
local service center.
• Do not subject the display to severe vibration or high impact conditions during operation.
• Do not knock or drop the display during operation or transportation.
• The eye bolt is for usage in short-time maintenance and installation. We suggest not to use the eye bolt for more than 1 hour.
Prolong usage is prohibited. Please keep a clear safety area under the display while using the eye bolt.
Maintenance:
• To protect your display from possible damage, do not put excessive pressure on the LCD panel. When moving your display,
grasp the frame to lift; do not lift the display by placing your hand or ngers on the LCD panel.
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the
power is o. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your display.
• To avoid the risk of shock or permanent damage to the set, do not expose the display to dust, rain, water or an excessively
moist environment.
• If your display becomes wet, wipe it with dry cloth as soon as possible.
• If a foreign substance or water gets in your display, turn the power o immediately and disconnect the power cord. Then
remove the foreign substance or water, and send the unit to the maintenance center.
• Do not store or use the display in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of your display and ensure a longer lifetime, we strongly recommend using the
display in a location that falls within the following temperature and humidity ranges.
Environmental absolute ratings
Item Min. Max. Unit
Storage temperature -20 65 °C
Operation temperature 0 40 °C
Glass Suraface temperature
(Operation)
0 65 °C
Storage humidity 5 90 % RH
Operating humidity 20 80 % RH
• LCD panel temperature need to be 25 degrees Celsius at all time for better luminance performance.
43BDL3017P/50BDL3017P/55BDL3017P
iii
• Only the lifetime of the display stated in this specication is guaranteed if the display is used under the proper operation
conditions.
IMPORTANT: Always activate a moving screen saver program when you leave your display unattended. Always activate a
periodic screen refresh application if the unit will display unchanging static content. Uninterrupted display of still or static
images over an extended period may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on your screen. This is
a well-known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost imaging” will
disappear gradually over a period of time after the power has been switched o.
WARNING: Severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired. This is also
not covered under the terms of your warranty.
Service:
• The casing cover should be opened only by qualied service personnel.
• If there is any need for repair or integration, please contact your local service center.
• Do not leave your display under direct sunlight.
If your display does not operate normally, having followed the instructions set out in this document, please
contact a technician or your local service center.
Stability Hazard.
The device may fall, causing serious personal injury or death. To prevent injury, this device must be securely attached to the
oor/wall in accordance with the installation instructions.
Read and follow these instructions when connecting and using your display:
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry
cloth when the power is o. However, never use alcohol, solvents or ammonia-based liquids.
• Consult a service technician if the display does not operate normally when you have followed the instructions
in this manual.
• The casing cover should be opened only by qualied service personnel.
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into the vents or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry. To avoid electric shock, do not expose it to rain or excessive moisture.
• When turning o the display by detaching the power cable or DC power cord, wait for 6 seconds before re-
attaching the power cable or DC power cord for normal operation..
• To avoid the risk of shock or permanent damage to the set do not expose the display to rain or excessive
moisture.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast
remains on the screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the
front of the screen. This is a well-known phenomenon that is caused by the shortcomings inherent in LCD
technology. In most cases the afterimage will disappear gradually over a period of time after the power has
been switched o. Be aware that the after-image symptom cannot be repaired and is not covered under
warranty.
• If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-pin
outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding
pin is an important safety feature.
EU Declaration of Conformity
This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member
States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), RoHS directive (2011/65/
EU).
This product has been tested and found to comply with the harmonized standards for Information Technology Equipment, these
harmonized standards published under Directives of Ocial Journal of the European Union.
ESD Warnings
When user close to the monitor may cause the equipment discharge and reboot to the display of main menu.
43BDL3017P/50BDL3017P/55BDL3017P
iv
Warning:
This equipment is compliant with Class A of EN55032/CISPR 32. In a residential environment this equipment may cause radio
interference.
Federal Communications Commission (FCC) Notice (U.S. Only)
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
Changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in re or shock hazard, do not expose this appliance to rain or excessive moisture.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Envision Peripherals Inc.
490 N McCarthy Blvd, Suite #120
Milpitas, CA 95035
USA
43BDL3017P/50BDL3017P/55BDL3017P
v
Polish Center for Testing and Certication Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that
works together (computer, display, printer, and so on) should have the same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a
fuse with a nominal value no larger than 16 amperes (A).
To completely switch o the equipment, the power supply cable must be removed from the power supply socket, which should
be located near the equipment and easily accessible.
A protection mark “B” conrms that the equipment is in compliance with the protection usage requirements of standards PN-
93/T-42107 and PN-89/E-06251.
Electric, Magnetic and Electromagnetic Fields (“EMF”)
1. We manufacture and sell many products targeted at consumers, which, like any electronic apparatus, in general have the
ability to emit and receive electromagnetic signals.
2. One of our leading Business Principles is to take all necessary health and safety measures for our products, to comply with
all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products.
3. We are committed to develop, produce and market products that cause no adverse health eects.
4. We conrm that if its products are handled properly for their intended use, they are safe to use according to scientic
evidence available today.
5. We play an active role in the development of international EMF and safety standards, enabling us to anticipate further
developments in standardization for early integration in its products.
43BDL3017P/50BDL3017P/55BDL3017P
vi
Information for U.K. only
(A)
(B)
WARNING - THIS APPLIANCE MUST BE EARTHED.
Important:
This apparatus is supplied with an approved moulded 13A plug. To change a fuse in
this type of plug proceed as follows:+
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.
3. Ret the fuse cover.
If the tted plug is not suitable for your socket outlets, it should be cut o and an
appropriate 3-pin plug tted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug without a
fuse is used, the fuse at the distribution board should not be greater than 5A.
NOTE: The severed plug must be destroyed to avoid a possible shock hazard should
it be inserted into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN & YELLOW - “EARTH” (“E”)
1. The GREEN & YELLOW wire must be connected to the terminal in the plug which is
marked with the letter “E” or by the Earth symbol or coloured GREEN or GREEN &
YELLOW.
2. The BLUE wire must be connected to the terminal which is marked with the letter
“N” or coloured BLACK.
3. The BROWN wire must be connected to the terminal which marked with the letter
“L” or coloured RED.
Before replacing the plug cover, make certain that the cord grip is clamped over the
sheath of the lead - not simply over the three wires.
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
43BDL3017P/50BDL3017P/55BDL3017P
vii
China RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》，以下部分列出了本产品中可能包含的有害
物质的名称和含量。
部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
外壳 O O O O O O
液晶显示屏 X O O O O O
电路板组件* X O O O O O
电源适配器 X O O O O O
电源线/连接线 X O O O O O
遥控器 X O O O O O
本表格依据SJ/T 11364 的规定编制。
*: 电路板组件包括印刷电路板及其构成的零部件，如电阻、电容、集成电路、连接器等。
O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572规定的限量要求。
上 表 中 打“ X”的部件，应功能需要，部分有害物质含量超出GB/T 26572规 定 的 限 量 要 求 ，但 符 合 欧 盟
RoHS法规要求（属于豁免部分）。
备注：上表仅做为范例，实际标示时应依照各产品的实际部件及所含有害物质进行标示。
1.
10 环保使用期限
此标识指期限 (十年 )，电子电气产品中含有的有害物质在正常使用的条件下不会发生外泄或突变，电
子电气产品用户使用该电子电气产品不会对环境造成严重污染或对其人身、财产造成严重损害的期限。
《废弃电器电子产品回收处理管理条例》提示性说明
为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终止时，请遵守国家废弃电器电子产品
回收处理相关法律法规，将其交给当地具有国家认可的回收处理资质的厂商进行回收处理，不当利用或
者处置可能会对环境和人类健康造成影响。
警告
此为 A级产品。在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对
干扰采取切实可行的措施。
43BDL3017P/50BDL3017P/55BDL3017P
viii
單元
限用物質及其化學符號
鉛
(Pb)
汞
(Hg)
鎘
(Cd)
六價鉻
(Cr+6)
多溴聯苯
(PBB)
多溴二苯醚
(PBDE)
塑料外框 ○ ○ ○ ○ ○ ○
後殼 ○ ○ ○ ○ ○ ○
液晶面板 － ○ ○ ○ ○ ○
電路板組件 － ○ ○ ○ ○ ○
電源線 － ○ ○ ○ ○ ○
其他線材 － ○ ○ ○ ○ ○
遙控器 － ○ ○ ○ ○ ○
喇叭（選配） － ○ ○ ○ ○ ○
風扇（選配） － ○ ○ ○ ○ ○
備考1.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考2.〝－〞係指該項限用物質為排除項目。
警語 : 使用過度恐傷害視力。
注意事項 :
(1) 使用30分鐘請休息10分鐘。
(2) 未滿2歲幼兒不看螢幕，2歲以上每天看螢幕不要超過1小時。
警告使用者 :
此為甲類資訊技術設備 , 於居住環境中使用時 , 可能會造成射頻擾動 , 在此種情況下 , 使用者會被
要求採取某些適當的對策。
Turkey RoHS:
Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur
Ukraine RoHS:
Обладнання відповідає вимогам Технічного регламенту щодо обмеження використання деяких небезпечних речовин в
електричному та електронному обладнанні, затвердженого постановою Кабінету Міністрів України від 3 грудня 2008 № 1057
End-of-Life Disposal
Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle
your product to increase the amount of reusable materials and to minimize the amount to be disposed of.
Please nd out about the local regulations on how to dispose of your old display from your local Philips dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional
information on recycling contact www.eia.org (Consumer Education Initiative)
43BDL3017P/50BDL3017P/55BDL3017P
ix
Waste Electrical and Electronic Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing
used electrical and electronic appliances, this product may not be disposed of with normal household waste. You
are responsible for disposal of this equipment through a designated waste electrical and electronic equipment
collection. To determine the locations for dropping o such waste electrical and electronic, contact your local
government oce, the waste disposal organization that serves your household or the store at which you purchased
the product.
Attention users in United States:
Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information, contact: www.
mygreenelectronics.com or www.eiae.org.
End of Life Directives-Recycling
Your new Public Information Display contains several materials that can be recycled for new users.
Please dispose of according to all Local, State, and Federal laws.
Restriction on Hazardous Substances statement (India)
This product complies with the “E-Waste (Management) Rules, 2016” CHAPTER V, rule 16, sub-rule (1) . Whereas New Electrical
and Electronic Equipment and their components or consumables or parts or spares do not contain Lead, Mercury, Cadmium,
Hexavalent Chromium, polybrominated biphenyls and polybrominated diphenyl ethers beyond a maximum concentration
value of 0.1% by weight in homogenous materials for lead, mercury, hexavalent chromium, polybrominated biphenyls and
polybrominated diphenyl ethers and of 0.01% by weight in homogenous materials for cadmium. except of exemptions set in
Schedule 2 of the Rule.
E-Waste Declaration for India
This symbol on the product or on its packaging indicates that this product must not be disposed of with
your other household waste. Instead it is your responsibility to dispose of your waste equipment by handing
it over to a designated collection point for the recycling of waste electrical and electronic equipment . The
separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the environment. For more
information about E -waste please visit http://www.india.philips.com/about/sustainability/recycling/index.
page and to know where you can drop o your waste equipment for recycling in India please contact on below
given contact details.
Helpline number: 1800-425-6396 (Monday to Saturday, 9 a.m. to 5:30 pm)
E-mail: india.callcentre@tpv-tech.com
43BDL3017P/50BDL3017P/55BDL3017P
x
Batteries
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation.
Please contact your local authority for details on the collection and recycling schemes.
For Switzerland: The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct method of disposal of the used
battery.
According to EU directive 2006/66/EC, the battery can’t be disposed improperly. The battery shall be separated to collect by
local service.
Após o uso, as pilhas
deverão ser entregues ao
estabelecimento comercial ou
e/ou baterias
rede de assistência técnica
autorizada.
Information for EAC
Month and year of manufacturing please refer information in Rating label.
Name and location of manufacturer ООО “Профтехника”
Адрес: 3-й Проезд Марьиной рощи, 40/1 офис 1. Москва, 127018, Россия
Importer and information
Наименование организации: ООО “Профтехника”
Адрес: 3-й Проезд Марьиной рощи, 40/1 офис 1. Москва, 127018, Россия
Контактное лицо: Наталья Астафьева,
+7 495 640 20 20
nat@profdisplays.ru
43BDL3017P/50BDL3017P/55BDL3017P
xi
Table Of Contents
1. Unpacking and Installation ........................................ 1
1.1. Unpacking ...........................................................1
1.2. Package Contents .............................................1
1.3. Installation Notes ..............................................1
1.4. Mounting on a Wall ......................................... 2
1.4.1. VESA Grid ............................................. 2
1.5. Mounting in Portrait Orientation ..................3
1.5.1. How to remove the logo ................... 3
1.6. Operating Instructions of Edge Alignment
Kit ........................................................................4
1.6.1. Installing the Edge Alignment Kit ....4
2. Parts and Functions ....................................................5
2.1. Control Panel ....................................................5
2.2. Input/Output Terminals..................................6
2.3. Remote Control ................................................ 7
2.3.1. General functions ............................... 7
2.3.2. ID Remote Control .............................8
2.3.3. Inserting the batteries in the remote
control ...................................................9
2.3.4. Handling the remote control ...........9
2.3.5. Operating range of the remote
control ...................................................9
2.4. USB Cover ........................................................ 10
2.5. AC Switch Cover ............................................. 10
3. Connecting External Equipment .............................11
3.1. Connecting External Equipment (DVD/
VCR/VCD)...........................................................11
3.1.1. Using HDMI video input ....................11
3.2. Connecting a PC ...............................................11
3.2.1. Using DVI input ...................................11
3.2.2. Using HDMI input ...............................11
3.2.3. Using DP input .................................... 12
3.3. Connecting Multiple Displays in a Daisy-
chain Conguration ........................................12
3.3.1. Display control connection .............12
3.4. IR connection ...................................................12
3.5. IR Pass-through Connection ........................13
3.6. Wire-connecting to Network .......................13
4. Operation ....................................................................14
4.1. Play multimedia les from USB device ......14
5. OSD Menu ...................................................................15
5.1. Navigating the OSD Menu .............................15
5.1.1. Navigating the OSD menu using the
remote control ...................................15
5.1.2. Navigating the OSD menu using the
display’s control buttons .................15
5.2. OSD Menu Overview ...................................... 15
5.2.1. Picture menu ......................................15
5.2.2. Screen menu ......................................16
5.2.3. Audio .................................................... 17
5.2.4. Conguration1 menu .........................17
5.2.5. Conguration2 menu ........................18
5.2.6. Option ..................................................19
6. Supported Media Formats .....................................22
7. Input Mode ................................................................. 23
8. Pixel Defect Policy ....................................................24
8.1. Pixels and Sub-Pixels ...................................24
8.2. Types of Pixel Defects + Dot Denition ....24
8.3. Bright Dot Defects ..........................................24
8.4. Dark Dot Defects ............................................25
8.5. Proximity of Pixel Defects ............................ 25
8.6. Pixel Defect Tolerances ................................25
8.7. MURA ................................................................ 25
9. Cleaning and Troubleshooting ...............................26
9.1. Cleaning ...........................................................26
9.2. Troubleshooting .............................................27
10. Warranty Statement .................................................28
11. Technical Specications ..........................................29
43BDL3017P/50BDL3017P/55BDL3017P
1
1. Unpacking and Installation
1.1. Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• As this product is high and heavy, the operation of moving the device is recommended to be performed by two technicians.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2. Package Contents
Please verify that you received the following items with your package content:
• LCD display
• Quick start guide
• Remote control with AAA
batteries
• Power cord
• RS232 cable
• RS232 daisy chain cable
• IR Sensor Cable
• Philips logo plate
• AC Switch Cover
• USB Cover
• Edge Alignment Kit-1
• Edge Alignment Kit-2 x 2
• Wire Clamper X 3
* The supplied power cord varies depending on destination.
LCD display Remote Control
and AAA Batteries
Quick start guide
Power Cord
IR Sensor Cable
USB Cover
RS232 Daisy Chain CableRS232 Cable
AC Switch Cover
Edge Alignment
Kit-1
Edge Alignment
Kit-2 x 2
Wire Clamper
X 3
Philips logo plate
* Dierences according to regions.
Display design and accessories may dier from those illustrated above.
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and
complies with the safety regulations of the particular country.
• You might like to save the package box and packing material for shipping the display.
1.3. Installation Notes
• Only use the power cable provided with this product. If an extension cord is required, please consult your service agent.
• The product should be installed on a at surface, or the product may tip over. Leave a space between the rear of the product
and the wall for proper ventilation. Do not install the product in a kitchen, bathroom or a place exposed to moisture, failure
to do so may shorten the life of the internal parts.
• Do not install the product where it is 3000m and higher in altitude. Failure to do so may result in malfunctions.
43BDL3017P/50BDL3017P/55BDL3017P
2
1.4. Mounting on a Wall
To mount this display on a wall, a standard wall-mounting kit (commercially available) is required. It is recommended that you
use a mounting interface that complies with TUV-GS and /or UL1678 standard in North America.
Protective Sheet
Table
VESA Grid
1. Spread a protective sheet which was wrapped around the display when it was packed on a at surface. Lay the display face-
down on the protective sheet to facilitate your operation without scratching the screen.
2. Ensure that you have all accessories necessary for any type of mounting (wall-mounting, ceiling mounting etc).
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in
damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper
installation.
4. For the wall-mounting kit, use M6 mounting screws (43BDL3017P with a length 14.5 mm longer than the thickness of the
mounting bracket,50BDL3017P/55BDL3017P with a length 12.2 mm longer than the thickness of the mounting bracket) and
tighten them securely.
1.4.1. VESA Grid
43BDL3017P 200(H) x 200(V) mm
50BDL3017P 400(H) x 400(V) mm
55BDL3017P 400(H) x 400(V) mm
Caution:
To prevent the display from falling:
• For wall or ceiling mounting, we recommend that you install the display with metal brackets which are commercially
available. For detailed instructions about the installation, refer to the guide that come with the bracket.
• To prevent the display from falling in case of earthquake or other natural disaster, please contact the manufacturer of the
bracket for the mounting location.
Required space for ventilation
Leave a space of 100 mm at the top, rear, right and left for ventilation.
100 mm 100 mm
100 mm
100 mm
43BDL3017P/50BDL3017P/55BDL3017P
3
1.5. Mounting in Portrait Orientation
This display can be installed in portrait orientation.
Rotate the display 90 degrees Counterclockwise. The “ ” logo should be on the right side when facing the display.
90° 90°
1.5.1. How to remove the logo
1. Prepare a piece of paper with a cutting area of logo as a
protector to prevent the front bezel from scratching.
2. Use a knife and carefully remove the logo sticker with the
paper placing beneath.
3. Tear o the logo sticker.
123
NOTE: We recommend you contact a professional technician when installing the display on a wall. We are not responsible for
any damage to the product if the installation is not performed by a professional technician.
43BDL3017P/50BDL3017P/55BDL3017P
4
1.6. Operating Instructions of Edge Alignment Kit
1.6.1. Installing the Edge Alignment Kit
Before installing the edge alignment kit, the display must by mounted to the video wall frame correctly.
• Use the thumb screw for easy mounting.
• Use the “Edge Alignment Kit-1” on 4 adjacent displays.
1 2
3 4
• Use the “Edge Alignment Kit -2” on 2 adjacent display.
1 2
NOTE: When installing the edge alignment kit, please consult a professional technician for proper installation. We accept no
liability for installations not performed by a professional technician.
43BDL3017P/50BDL3017P/55BDL3017P
5
2. Parts and Functions
2.1. Control Panel
9
1 2 3 4 5 6 7 8
1 [ ] button
Press this button to turn the display On or turn the
display to standby mode.
2 [MUTE] button
Press this button to mute the sound or reactivate sound.
3 [INPUT] button
Choose the input source.
Conrm a selection in the OSD menu.
4 [ ] button
Increase the adjustment while OSD menu is on, or
increase the audio output level while OSD menu is o.
5 [ ] button
Decrease the adjustment while OSD menu is on, or
decrease the audio output level while OSD menu is o.
6 [ ] button
Move the selected item one level up while the OSD
menu is On.
7 [ ] button
Move the selected item one level down while the OSD
menu is On.
8 [MENU] button
Return to the previous menu while the OSD menu is On.
This button can also be used to activate the OSD menu
when the OSD menu is O.
9 Remote control sensor and power status indicator
• Receives command signals from the remote control.
• Indicates the operating status of the display:
- Lights green when the display is turned on
- Lights red when the display is in standby mode
- Lights amber when the display enters APM mode
- When {SCHEDULE} is enabled, the light blinks
green and red
- If the light blinks red, it indicates that a failure has
been detected
- Lights off when the main power of the display is
turned o
43BDL3017P/50BDL3017P/55BDL3017P
6
2.2. Input/Output Terminals
21
12
13
14
15
16
17
18
3 4 5 6 7 8 9 10 11
HDMI OUT
HDMI 2 IN HDMI 3 IN
HDMI 1 IN
DVI-I IN
DP IN DP OUT
RS232
OUT
RS232
IN
USB A
RJ45
MICRO SD
IR-OUT
AUDIO OUT
PC LINE IN
IR-IN
1 AC IN
AC power input from the wall outlet.
2 MAIN POWER SWITCH
Switch the main power between On and O.
3 DisplayPort IN / 4 DisplayPort OUT
DisplayPort video input / output.
5 DVI-I IN
DVI-I video input.
6 HDMI 1 IN / 7 HDMI 2 IN / 8 HDMI 3 IN /
9 HDMI OUT
HDMI video/audio input /output
10 RS232 IN / 11 RS232 OUT
RS232 network input / output for the loop-through
function.
12 IR IN / 13 IR OUT
IR signal input / output for the loop-through function.
NOTES:
• This display’s remote control sensor will stop working
if the jack [IR IN] is connected.
• To remotely control your A/V device via this display,
refer to page 13 for IR Pass Through connection.
14 AUDIO OUT
Audio output to external AV device.
15 PC LINE IN
Audio input for VGA source (3.5mm stereo phone).
16 USB A
Connect your USB storage device and service port.
17 MICRO SD
Insert a Micro SD card.
18 RJ-45
LAN control function for the use of remote control signal
from control center.
43BDL3017P/50BDL3017P/55BDL3017P
7
2.3. Remote Control
2.3.1. General functions
1
2
3
5
7
8
17
9
11
10
13
15
12
14
16
4
6
1 [
/
] POWER button
[ ]Turn the power On.
[ ]Turn the power O.
2 [PLAY] buttons
Control playback of media les.
3 [ ] HOME button
Access the OSD menu.
4 [ ] SOURCE button
Choose input source. Press [ ] or [ ] button to choose
from USB, Network, HDMI 1, HDMI 2, DisplayPort,
DVI-D, YPbPr, AV or VGA. Press [ ] button to
conrm and exit.
5 [ ] LIST button
Reserved.
6 [ ] INFO button
Display information about current activity
7 [ ][ ][ ][ ]NAVIGATION buttons
Navigate through menus and choose items..
8 [ ] button
Conrm an entry or selection.
9 [ ] BACK button
Return to the previous menu page or exit from the
previous function.
10 [ ] MUTE button
Press to turn the mute function on/o.
11 [ ] [ ] [ ] [ ] COLOR buttons
Choose tasks or options
12 [NUMERIC] buttons
Enter text for network setting, and set up ID for ID mode
13 [ ] FORMAT button
Change zoom mode.
14 [ ] OPTIONS button
Access currently available options, picture and sound
menus.
15 [ ] POINTER button
Mouse function for Android
16 [ ] ADJUST button
Access currently available options, picture and sound
menus.
17 [ ] [ ] VOLUME button
Adjust the volume.
43BDL3017P/50BDL3017P/55BDL3017P
8
2.3.2. ID Remote Control
Set remote control ID number when using several displays.
Press [ID] button. The red LED blinks twice.
1. Press [ID SET] button for more than 1 second to enter the
ID Mode. The red LED lights up.
Press the [ID SET] button again to exit from ID mode. The
red LED lights o.
Press the digit numbers [0] ~ [9] to select the display you
want to control.
For example: press [0] and [1] for display No.1, press [1] and [1]
for display No.11.
The numbers available are from [01] ~ [255].
2. Not pressing any button within 10 seconds will exit the
ID Mode.
3. If a wrong button is pressed, wait 1 second after the red
LED lights o and then lights up again, then press the
correct digits again.
4. Press [ENTER] button to conrm. The red LED blinks
twice and then lights o.
NOTE:
• Press [NORMAL] button. The green LED blinks twice,
indicating the display is in normal operation.
• It is necessary to set up the ID number for each display
before selecting its ID number.
• Use “ ” (pause) key on the remote control to freeze
the screen. Use “ ” (play) key on the remote control to
unfreeze the screen.
• The “freeze” feature only can be adopted on “real”
video sources like VGA, AV, YPbPr, HDMI, DVI, DP.
• Any operation on the remote control or video mode
change will unfreeze the screen.
43BDL3017P/50BDL3017P/55BDL3017P
9
2.3.3. Inserting the batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
1. Press and then slide the cover to open it.
2. Insert batteries with the correct polarity (+) and (-).
3. Replace the cover.
Caution:
Incorrect use of batteries may cause leakage or explosion. Be sure to follow the instructions below:
• Insert “AAA” batteries with the correct polarity (+ and -).
• Do not mix battery types.
• Do not use a new battery with a used one together. Otherwise, it may cause leakage or shorten the life of the batteries.
• Remove the dead batteries immediately to avoid battery leakage in the battery compartment. Do not touch exposed battery
acid, as it may cause injury to your skin.
• Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of
ammable liquid or gas; and a battery subjected to extremely low air pressure that may result in an explosion or the leakage
of ammable liquid or gas.
NOTE: Remove the batteries from the battery compartment when not using for an extended period of time.
2.3.4. Handling the remote control
• Do not drop or apply shock to the remote control.
• Do not allow any liquid to get inside the remote control. If water has entered the remote control, wipe the remote control
with a dry cloth immediately.
• Do not place the remote control near heat and steam sources.
• Do not attempt to disassemble the remote control, unless you need to place batteries in the remote control.
2.3.5. Operating range of the remote control
Pointing the remote control at the remote sensor on the display.
Use the remote control within 5 m from the sensor on the display at an
angle of 20 degrees from the left and right.
NOTE:
• The remote control may not function properly when the remote control
sensor on the display is under direct sunlight or strong illumination, or
when an obstacle blocks the signal transmission.
• Use an IR sensor cable for better performance of the remote control.
(Refer to 3.4. IR connection for details)
20° 20°
43BDL3017P/50BDL3017P/55BDL3017P
10
2.4. USB Cover
• Use the USB cover and screws to cover the USB stick and micro SD card.
1. Install the USB stick and micro SD card.
2. Use the screws provided to x the USB cover.
• Maximum USB stick size recommended:
43BDL3017P / 50BDL3017P: 20(W)x10(H)x60(L) mm
55BDL3017P: 20(W)x10(H)x45(L) mm
L
H
W
2.5. AC Switch Cover
• Use AC Switch Cover to cover the AC switch.
1. Install the AC Switch Cover.
2. Fix the AC Switch Cover with the screw provided.
43BDL3017P/50BDL3017P/55BDL3017P
11
3. Connecting External Equipment
3.1. Connecting External Equipment (DVD/VCR/VCD)
3.1.1. Using HDMI video input
DVD / VCR / VCD
HDMI Out
[HDMI IN]
HDMI OUT
HDMI 2 IN HDMI 3 IN
HDMI 1 IN
RS232
OUT
RS232
IN
3.2. Connecting a PC
3.2.1. Using DVI input
[DVI IN]
PC
[PC LINE IN]
Audio Out DVI Out
RS232
OUT
PC LINE IN
HDMI OUT
HDMI 2 IN HDMI 3 IN
HDMI 1 IN
DVI-IN
DP IN DP OUT
RS232
OUT
RS232
IN
3.2.2. Using HDMI input
PC
HDMI Out
[HDMI IN]
HDMI OUT
HDMI 2 IN HDMI 3 IN
HDMI 1 IN
RS232
OUT
RS232
IN
43BDL3017P/50BDL3017P/55BDL3017P
12
3.2.3. Using DP input
PC
DP Out
[DP IN]
DVI-I
RS232
OUT
RS232
IN
DP IN
3.3. Connecting Multiple Displays in a Daisy-chain Configuration
You can interconnect multiple displays to create a daisy-chain conguration for applications such as a menu board.
3.3.1. Display control connection
Connect the [RS232 OUT] connector of DISPLAY 1 to the [RS232 IN] connector of DISPLAY 2.
DISPLAY 1 DISPLAY 2
PC
[RS232 IN]
[RS232]
[RS232 OUT] [RS232 IN]
3.4. IR connection
DISPLAY 1
[IR IN]
External
IR Receiver
NOTE:
This display’s remote control sensor will stop working if the [IR IN] is connected.
43BDL3017P/50BDL3017P/55BDL3017P
13
3.5. IR Pass-through Connection
DVD / VCR / VCD
(DVD / VCR / VCD)
Remote Control
[IR OUT]
[IR IN]
3.6. Wire-connecting to Network
PC
[RJ-45]
[RJ-45] ROUTER
INTERNET
Network Settings:
1. Switch the router on and enable its DHCP setting.
2. Connect the router to this display with an Ethernet cable.
3. Press [ ] HOME button on the remote control, then select Setup.
4. Select Connect to network, then press [ ] button.
5. Wait until this display nds the network connection.
6. If the “End User License Agreement” window prompts, accept the agreement.
NOTE: Connecting with a shielded CAT-5 Ethernet cable to comply with the EMC directive.
43BDL3017P/50BDL3017P/55BDL3017P
14
4. Operation
NOTE: The control button described in this section is mainly
on the remote control unless specied otherwise.
4.1. Play multimedia files from USB device
1. Connect your USB device to the USB port on the display.
USB
USB A
RJ45
MICRO SD
IR-OUT
AUDIO OUT
PC LINE IN
IR-IN
2. Press [ ] SOURCE button, choose Media Player,
and press [ ] button.
VGA
DVI
HDMI 1
HDMI 2
HDMI 3
Media Player
3. The playable les for the connected USB device will
be detected automatically. The les are automatically
sorted into 3 types: Photo, Music and Movie.
USB A
MUSIC MOVIEPHOTO
4. Press [ ] or [ ] button to choose the item. Press [ ]
button to enter its play list.
5. Press [ ], [ ], [ ] or [ ] button to choose a le. Press
[ ]or [ ] button to start playing.
6. Follow the on-screen instruction to control the play
option.
7. Press [PLAY] buttons ( ) to control playing.
1 / 2
Return aaa1
xxx1 xxx2 xxx3 123
aaa2 aaa3
8. Press [ ], [ ], [ ] or [ ] button to choose “Return" item
then press [ ] button to return to the top layer.
43BDL3017P/50BDL3017P/55BDL3017P
15
5. OSD Menu
An overview of the On-Screen Display (OSD) structure
is shown below. You can use it as a reference for further
adjustment of your display.
5.1. Navigating the OSD Menu
5.1.1. Navigating the OSD menu using the
remote control
1. Press [ ] button on the remote control to display the
OSD menu.
2. Press [ ] or [ ] button to select the item to adjust.
3. Press [OK] or [ ] button to enter the submenu.
4. In the submenu, press [ ] or [ ] button to toggle
between items, press [ ] or [ ] button to adjust the
settings. If there is a submenu, press [OK] or [ ] button
to enter the submenu.
5. Press [ ] button to return to the previous menu, or
press [ ]button to exit from the OSD menu.
5.1.2. Navigating the OSD menu using the
display’s control buttons
1. Press [MENU] button to display the OSD menu.
2. Press [ ] or [ ] button to select the item to adjust.
3. Press [ ] button to enter the submenu.
4. In the submenu, press [ ] or [ ] button to toggle
between items, press [ ] or [ ] button to adjust
settings. If there is a submenu, press [ ] button to enter
the submenu.
5. Press [MENU] button to return to the previous menu,
or keep pressing [MENU] button to exit from the OSD
menu.
5.2. OSD Menu Overview
5.2.1. Picture menu
Audio
Screen
Picture
Conguration 1
Conguration 2
Option
Contrast
Sharpness
Color
Tint
Brightness
Black Level
Gamma
Color Temperature
Smart Picture
Smart Power
Smart Mode
Noise Reduction
50
50
50
50
Native
Standard
o
50
50
0
Low
Brightness
Adjust the brightness of this display’s backlight.
Contrast
Adjust the contrast ratio for the input signal.
Sharpness
This function is digitally capable to keep a distinct image at
all times.
Adjust the sharpness of the picture for each picture mode.
Black Level
Adjust the image brightness for the background.
NOTE: sRGB picture mode is standard and cannot be
changed.
Tint (Hue)
Adjust the tint of the screen.
Press + button the esh tone color becomes greenish.
Press - button the esh tone color becomes purplish.
NOTE: VIDEO mode only.
Color(Saturation)
Adjust the color of the screen.
Press + button to increase color depth.
Press - button to decrease color depth.
NOTE: VIDEO mode only
Noise Reduction
Adjust the noise reduction level.
Gamma
Select a display gamma. It refers to the brightness
performance curve of signal input. Choose from {Native} /
{2.2} / {2.4} / {s gamma} / {D-image}.
NOTE: sRGB picture mode is standard and cannot be
changed.
Color Temperature
It is used to adjust the color temperature.
The image becomes reddish as the color temperature
decreases, and becomes bluish as the color temperature
increases.
43BDL3017P/50BDL3017P/55BDL3017P
16
Smart Picture
PQ setting
{Standard}/{Highbright}/{Warm}.
Smart Power
Smart Power control is not relative to brightness control:
1. Initial setting Brigthness
70 (in the range from 0-100)
Power consumption 70% of maximum power
consumption
2. Smart Power
OFF: no adaptation
MEDIUM: 65% of power consumption relative to current
settings
HIGH: 80% of power consumption relative to current
settings
Picture Reset
Reset all settings in the Picture menu.
Select “Yes” and press “SET” button to restore to factory
preset data.
Press “EXIT” button to cancel and then return to the
previous menu.
5.2.2. Screen menu
Audio
Screen
Picture
Conguration 1
Conguration 2
Option
V. Position
Clock
Zoom Mode
Custom Zoom
H. Position
Clock Phase
Auto Adjust
Screen Reset
Full
H position
Control Horizontal Image position within the display area of
the LCD.
Press + button to move screen to right.
Press - button to move screen to left.
NOTE: VGA input only.
V position
Control Vertical Image position within the display area of
the LCD.
Press + button to move screen to up.
Press - button to move screen to down.
NOTE: VGA input only.
Clock
Press + button to expand the width of the image on the
screen to the right.
Press - button to narrow the width of the image on the
screen to the left.
NOTE: VGA input only.
Clock Phase
Improves focus, clarity and image stability by increasing or
decreasing this setting.
NOTE: VGA input only.
Zoom mode
PC mode: {Full} / {4:3} / {1:1} / {16:9}/ {21:9}/ {Custom}.
Video mode: {Full} / {4:3} / {1:1} / {16:9}/ {21:9}/ {Custom}.
*Zoom mode setting is dened by input. If input in
multi-windows, the setting will apply for windows with the
same input.
The INFO OSD will show the latest setting.
Full
This mode restores the correct
proportions of pictures transmitted in
16:9 using the full screen display.
4:3
The picture is reproduced in 4:3
format and a black band is displayed
on either side of the picture.
1:1
This mode displays the image pixel-
by-pixel on screen without scaling the
original image size.
16:9
The picture is reproduced in 16:9
format and a black band at the top
and bottom.
21:9
The picture is reproduced in 21:9
format and a black band at the top
and bottom.
Custom
Choose to apply the custom zoom
settings in the Custom Zoom
submenu.
Custom zoom
You can use this function to further customize the zoom
settings to suit the image you want to display.
NOTE: This item is functional only when the {Zoom mode}
is set to {Custom}.
Zoom
Expands the horizontal and vertical
sizes of the image simultaneously.
H zoom
Expands the horizontal size of the
image only.
V zoom
Expands the vertical size of the image
only.
43BDL3017P/50BDL3017P/55BDL3017P
17
H position
Moves the horizontal position of the image left
or right.
V position
Moves the vertical position of the image up or
down.
Auto adjust
Press “Set” to detect and adjust H position, V position,
Clock, Phase automatically.
NOTE: VGA input only.
Screen reset
Reset all settings in the Screen menu to factory preset
values.
5.2.3. Audio
Audio
Screen
Picture
Conguration 1
Conguration 2
Option
Treble
Bass
Volume Minimum
Balance
Volume
Audio Out Volume
Volume Maximum
Mute
50
50
0
30
O
O
On
30
0
100
Audio source
Audio Reset
Speaker
Sync.Volume
Digital
Balance
Adjust to emphasize left or right audio output balance.
Treble
Adjust to increase or decrease higher-pitched sounds.
Bass
Adjust to increase or decrease lower-pitched sounds.
Volume
Adjust the volume.
Audio Out Volume
Adjust to increase or decrease the line out audio output
level.
Minimum volume ≤ Volume ≤ Maximum volume
NOTE: This function will be disabled when Audio Out Sync
is ON.
Volume Maximum
Adjust your own limitation for the maximum volume setting.
Volume Minimum
Adjust your own limitation for the minimum volume setting.
Mute
Turn the mute function on/o.
Speaker
Turn the internal speaker on/o.
NOTE: This function is only availavle when “Audio Out Sync”
is on.
Sync. Volume
Enable/disable audio out (line out) volume adjustability to
sync with internal speakers volume, but PD Internal speaker
sound will be forced to be mute.
Audio source
Select the audio input source.
Analog: audio from audio input.
Digital : audio from HDMI/DVI audio.
Displyport: audio from DP
Audio Reset
Reset all settings in the Audio menu to factory preset
values.
5.2.4. Configuration1 menu
Panel Saving
RS232 routing
WOL
Switch on state Last status
RS232
Last Input
O
On
O
O
Boot On Source
Light Sensor
Power LED Light
Network Settings
Conguration1 Reset
Factory Reset
Human Sensor
Audio
Screen
Picture
Conguration 1
Conguration 2
Option
Switch on State
Select the display status when you connect the power cord
next time.
• {Power o} - The display will remain o when the power
cord is connected to a wall outlet.
• {Forced on} - The display will turn on when the power
cord is connected to a wall outlet.
• {Last status} - The display will return to the previous
power status (on/o/standby) when removing and
replacing the power cord.
Panel saving
Choose to enable the panel saving functions and thus
reduce the risk of “image persistence” or “ghost-imaging”.
• {Brightness} - Select {On} and the image brightness
will be reduced to an appropriate level. The Brightness
setting in the Picture menu will be unavailable when
selected.
• {Pixel shift} - Select the time interval ({Auto} / {10 ~
900} Seconds / {O}) for the display to slightly expand
the image size and shift the position of pixels in four
directions (up, down, left, or right).
RS232 routing
Select the network control port.
Choose from: {RS232} / {LAN ->RS232}.
Boot on source
Select the source when booting up.
43BDL3017P/50BDL3017P/55BDL3017P
18
WOL
Choose to turn on or o the wake on LAN function.
Choose from : {O} / { On}
Light sensor (require Philips accessory CRD41 External
Sensor Box)
Choose to turn on or o backlight adjustment according to
environment brightness.
Choose from : {O} / { On}
Human sensor (require Philips accessory CRD41 External
Sensor Box)
This function will turn the backlight On when it senses the
presence of human and turn it o after a specied period of
time.
The options are:
• {O} (Default), {10 Min.}, {20 Min.}, {30 Min.}, {40 Min.},
{50 Min.}, {60 Min.}
Power LED Light
Select {O} to turn o the indicator.
Network settings
• DHCP Enable -> Cannot modify IP address/Subnet
mask/Default gateway
• DHCP Disable-> Can manually input IP address/Subnet
mask/Default gateway.
Conguration1 reset
Reset all settings in Conguration1 menu to the factory
preset values.
Factory reset
Reset all settings in the OSD menus of {Picture}, {Screen},
{Audio}, {PIP}, {Conguration1}, {Conguration2}, and
{Advanced option} to the factory preset values.
Press [ ] or [ ] button to select {Reset}, and press [OK]
button to do the reset.
5.2.5. Configuration2 menu
Audio
Screen
Picture
Conguration 1
Conguration 2
Option
Information OSD
Logo
OSD turn o
OSD transparency
Monitor ID
Monitor Info
HDMI EDID
Heat Status
OSD Rotation
Language
Conguration2 Reset
0
15
On
English
Landscape
1 . 4
4 Sec
OSD turn o
Set the period of time the OSD (on-screen display) menu
stays on the screen.
The options are: {5 ~ 100} seconds.
OSD Transparency
Adjust OSD transparency.
• {0} - Transparency o.
• {1-100} - Transparency level 1-100
Information OSD
Set the period of time the information OSD is displayed on
the upper right corner of the screen. The information OSD
will display when input signal is changed.
The information OSD will remain on the screen with {O}
selection.
The options are: {1 - 60} seconds.
Logo
Choose to enable or disable the picture of Logo when
turning on your display.
The options are: {O} /{On}
Monitor ID
Set the ID number for controlling the display via the RS232
connection.
Each display must have a unique ID number when multiple
sets of display are connected. Monitor ID number range is
between 1 to 255.
• {1-255} – {Monitor ID} The default setting is 1.
• {1-254} – {Monitor group} The default setting is 1.
• {1-15} – {Tiling matrix} The default setting is 1.
• {Auto ID} The {Auto ID} setup function enables setting up
{Monitor ID} of connected machine according to {Tiling
matrix} settings. Example: Tiling matrix sets as 4
• {Tiling matrix}: Tiling matrix number range is between 1 to
15. The default setting is 1.
Monitor Id
Monitor Id
Monitor group
1
1
• {Auto ID}: The option are: {Start} / {End}. The default is
{End}.
• Switch to Start option to set up IDs of machines
backward from current one.
Once the setup is completed, the option exits to End
automatically.
To use this function, serially connect all machines with
RS-232 cable and set their Control ports to RS-232 too.
1 2
5 6
34
7 8
9 10 11 12
13 14 15 16
Heat status
This function allows you to check the thermal status at any
time.
43BDL3017P/50BDL3017P/55BDL3017P
19
Monitor information
Shows information about your display, including Input
source, Resolution, Model name, SW version, serial number,
operation hours and MAC address.
Monitor information
Model name
Serial NO.
Operation hours
SW Version
MAC address
XXXX
XXXX
XXXX
XXXX
XXXX
HDMI EDID
Switch HDMI EDID type: {HDMI 1.4}, {HDMI 2.0}.
OSD Rotation
Landscape/Portrait
Language
Set OSD menu language.
Conguration2 reset
Reset all settings in Conguration2 menu to the factory
preset values.
5.2.6. Option
IR Control
Keyboard Control
O Timer O
O
O
5 Sec
Date and Time
Input Resolution
Tiling
Schedule
Auto Signal Detection
Power Save
Autoplay
Slideshow Duration
HDMI with One Wire
Audio
Screen
Picture
Conguration 1
Conguration 2
Option
Input resolution
Set the resolution of the VGA input. This is only required
when the display is unable to detect the VGA input
resolution correctly.
NOTE: This item is functional for VGA input only.
The options are:
• {1024x768 / 1280x768 / 1360x768 / 1366x768}
• {1400x1050 / 1680x1050}
• {1600x1200 / 1920x1200}
• {Auto}: Determines the resolution automatically.
The selected settings will become eective after turning o
the power and turning it on again.
IR control
Select the operation mode of the remote control when
multiple displays are connected via an RS232C connection.
• {Normal} - All displays can be operated normally by the
remote control unit.
• {Primary} - Designate this display as the primary display
for remote control operation. Only this display can be
operated by the remote control. (In primary mode, IR
key will always be processed regardless the monitor id/
group settings).
• {Secondary} - Designate this display as the secondary
display. This display can not be operated by the remote
control, and will only receive the control signal from the
primary display via the RS232C connection.
• {Lock All} / {Lock all but Volume} / {Lock all but Power}
/ {Lock all except PWR & VOL}- Lock the remote control
function of this display. To unlock, press and hold
the [ ] INFO button on the remote control for 6 (six)
seconds.
Keyboard control
Choose to enable or disable the display keyboard (control
buttons) function.
• {Unlock} - Enable the keyboard function.
• {Lock All} / {Lock all but Volume} / {Lock all but Power}
/ {Lock all except PWR & VOL} - Disable the keyboard
function.
NOTE: “Keyboard Control Lock Mode” This function
completely disables the access to all Keyboard
Control functions. To enable or disable the
keyboard control lock, press both [ ] and [ ]
buttons and hold down continuously for more than
3 seconds.
Tiling
With this function you can create a single large-screen
matrix (video wall) that consists of up to 225 sets of this
display (up to 15-sets on the vertical and 15-sets on the
horizontal sides). This function requires a daisy-chain
connection.
1
1
1
13
22
7
7
O Timer
Set automatically power o time (in hours).
Date and time
Set the current date and time for the display’s internal clock.
NOTES:
The denition and behavior of the Daylight saving time:
The current implementation of daylight saving is a reminder
tool for the user who doesn’t know how to adjust the clock
of daylight saving.
It does not adjust the real time clock automatically. The
problem is that there are no standard rules on when to
adjust the clock dened by region or country. To solve this
problem, the user must be able to set the daylight saving
start/end date. When daylight saving correction is on (user
selectable) then the real time clock should be adjusted at
the time set of the daylight saving on/o date. At the start
date of daylight saving, the clock should be adjusted 1 hour
43BDL3017P/50BDL3017P/55BDL3017P
20
forward at 2 o’clock. At the end date of daylight saving, the
clock should be adjusted 1 hour backward at 2 o’clock.
The existing daylight on/o menu should be replaced by
the following menu structure:
The menu item {Daylight saving} opens the submenu that
contains the following items:
• Menu item {Daylight saving start date} Selection item {1st,
2nd, 3rd, 4th, last} Sunday of selection item {1-12 month}
• Menu item {Daylight saving stop date} Selection item {1st,
2nd, 3rd, 4th, last} Sunday of selection item {1-12 month}
• Menu item {Correction time} Selection item {0.5, 1.0, 1.5,
2.0} hour
• Menu item {Daylight saving} Selection item {on, o}
When “daylight saving” is “on”, the real time clock will be
adjusted automatically at the daylight saving time (e.g.
April 5, 2015, 02.00 o’clock: time will be set 1 hour later
or October 25, 2015, 02.00 o’clock: time will be set 1 hour
earlier).
Schedule
This function allows you to program up to 7 (seven) dierent
scheduled time intervals for the display to activate.
You can select:
• The time for the display to turn On and O.
• The days in a week for the display to activate.
• Which input source the display will use for each
scheduled activation period.
NOTE: It is recommended that you set up the current date
and time in the {Date and time} menu before using
this function.
1. Press [OK] or [ ] button to enter the submenu.
Schedule 1
Schedule 2
Schedule 3
Schedule 4
Schedule 5
Schedule 6
Schedule 7
Schedule
2. Press [ ] or [ ] button to select a schedule item (item
number 1 - 7), and press [OK] or [ ] button to enter the
submenu.
Schedule 1
Schedule 2
Schedule 3
Schedule 4
Schedule 5
Schedule 6
Schedule 7
Schedule
Status
Source
On Time
Off Time
Repeat modes
USB Play List
Off
HDMI1
-- : --
-- : --
None
• {Status} - Press [ ] or [ ] button to select the status
On or O.
• {Source} - Press [ ] or [ ] button to select the input
source.
• {On Time} - Press [ ] or [ ] button to adjust and the
display will turn on at the specied time.
• {O Time} - Press [ ] or [ ] button to adjust and the
display will turn o at the specied time.
Leave hour and minute options empty if you do not want
to use the function of power-on or power-o schedule.
• {Repeat modes} -Press [ ] button to select which day
in a week this schedule item will take eect, and then
press the [OK] button.
3. For additional schedule settings, press [ ], then repeat
the steps above. A check mark in the box next to the
number of the schedule item indicates that the selected
schedule is in eect.
NOTES:
• If the schedules overlap, the scheduled power-on time
takes priority over scheduled power-o time.
• If there are two schedule items programmed for the
same time, the highest numbered schedule takes
priority. For example, if schedule items #1 and #2 both
set the display to power on at 7:00 AM and o at 5:00
PM, then only schedule item # 2 will take eect.
HDMI with One Wire
CEC control.
• {O} - Disable CEC.(Default)
• {On} - Enable CEC.
Auto signal detection
This function allows the display to detect and display
available signal sources automatically.
• {O} - Once an input is connected, it can only be
selected manually.
If the selected input has signal, set the system to display the
image automatically according to the search order of each
option.
The options are: {Auto} / {Failover}
• {Auto}: Dispalyport->VGA->DVI-I->HDMI1->HDMI2-
>HDMI3->Media Player
• {Failover}
- Failover 1: User-dened setting. Default:HDMI 1.
- Failover 2: User-dened setting. Default:HDMI 1.
- Failover 3: User-dened setting. Default:HDMI 1.
- Failover 4: User-dened setting. Default:HDMI 1.
- Failover 5: User-dened setting. Default:HDMI 1.
- Failover 6: User-dened setting. Default:HDMI 1.
- Failover 7: User-dened setting. Default:HDMI 1.
If the primary signal is lost then the display begin failover
by searching the next available source that is dened in the
priority list.
Please note that failover will suspend under the following
conditions and failover will resume when signal is lost again.
- Boot On Source : When the display is powered on, it
will go to the source dened in this OSD option.
-Scheduler: When the display is powered on by
43BDL3017P/50BDL3017P/55BDL3017P
21
scheduler, it will go to the corresponding source
according to the current time.
-User operation: No matter what current source it is,
when user manually changes source, the failover will
suspend.
To make sure failover starts from the 1st priority source after
powering on, please set the 1st priority source as boot on
source too.
Power Save
Mode 1 [TCP o, WOL on, auto o]
Mode 2 [TCP o, WOL on, auto on/o]
Mode 3 [TCP on, WOL o, auto on/o]
Mode 4 [TCP on, WOL o, no auto on/o]
Autoplay
Choose to play source type. The options are: {O} / {SD}/
{USB}.
Slideshow Duration
Duration of each picture for autoplay and Play List.
Play List
Choose 1 playlist to play, support up to 7 playlists.
USB Cloning
Copy PD settings from one set to another.
Import: Import settings from another set.
Export: Export settings to another set.
Firmewre update
Update rmware via SD or USB disk.
Option Reset
Reset all settings in the Option menu to factory preset values.
43BDL3017P/50BDL3017P/55BDL3017P
22
6. Supported Media Formats
USB Multimedia Formats
Video format
Video Codec Resolution Bit Rate
MPEG1/2 1080P@30fps 40Mbps
H.264 1080P@30fps 50Mbps
WMV3 1080P@30fps 40Mbps
Motion JPEG 640x480@30fps 40Mbps
Audio format
Audio Codec Sampling Rate Channel Bit Rate
MPEG1/2 Layer1 16KHz-48KHz Up to 2 32Kbps-448Kbps
MPEG1/2 Layer2 16KHz-48KHz Up to 2 8Kbps-384Kbps
MPEG1/2 Layer3 16KHz-48KHz Up to 2 8Kbps-320Kbps
AAC, HEAAC 8KHz-48KHz Up to 5.1 32Kbps-448Kbps
Photo format
Image Photo Resolution
JPEG Base-line 15360x8640
(1920x8 x 1080x8)
Progressive 1024x768
PNG non-interlace 9600x6400
interlace 1200x800
BMP 9600x6400
NOTES:
• Sound or video may not work if the contents have a standard bit
rate/frame rate above the compatible Frame/sec listed in the
table above.
• Video content with a Bit rate or Frame rate larger than the rate
specied in the table above can cause choppy video during
playback.
HDCP support table
Input Source HDMI Ver HDCP 1.4 HDCP 2.2
DVI HDMI 1.4b V X
HDMI1
HDMI 1.4b V X
HDMI 2.0 V V
HDMI2
HDMI 1.4b V X
HDMI 2.0 V V
HDMI3
HDMI 1.4b V X
HDMI 2.0 V V
43BDL3017P/50BDL3017P/55BDL3017P
23
7. Input Mode
Timing support:
Item Resolution H.Freq. (KHz) V.Freq. (Hz)
1 720×400 @70Hz DOS 31.469 70.087
2 640×480 @60Hz DMT 31.469 59.94
3 640×480 @67Hz MAC 35 66.667
4 640×480 @72Hz DMT 37.861 72.809
5 640×480 @75Hz DMT 37.5 75
6 800×600 @56Hz DMT 35.156 56.25
7 800×600 @60Hz DMT 37.879 60.317
8 800×600 @72Hz DMT 48.077 72.188
9 800×600 @75Hz DMT 46.875 75
10 1024×768 @60Hz DMT 48.363 60.004
11 1024×768 @70Hz DMT 56.476 70.069
12 1024×768 @75Hz DMT 60.023 75.029
13 1152×864 @75Hz DMT 67.5 75
14 1152×870 @75Hz MAC 68.681 75.062
15 1280×720 @60Hz CVT16:9 44.772 59.855
16 1280x800 @60Hz CVT16:10 49.702 59.81
17 1280×1024 @60Hz DMT 63.981 60.02
18 1440×900 @60Hz CVT16:10 R 55.469 59.901
19 1440×900 @60Hz CVT16:10 55.935 59.887
20 1600×1200 @60Hz CVT16:9 75 60
21 1680×1050 @60Hz CVT16:9 R 64.674 59.883
22 1680×1050 @60Hz CVT16:9 65.29 59.954
23 1920×1080 @60Hz CVT-RB /
XBOX360
66.7 60
24 1920×1080 @60Hz DMT-RB 67.5 60
25 480P@60Hz 31.469 59.94
26 720P@60Hz 44.955 59.94
27 1080I@60Hz 33.716 59.94
28 1080P@60Hz 67.433 59.94
29 576P@50Hz 31.25 50
30 720P@50Hz 37.5 50
31 1080I@50Hz 28.125 50.08
32 1080P@50Hz 56.25 50
33 3840x2160@30 67.5 30
34 3840x2160@60 135 60
• The PC text quality is optimum in UHD mode (3840 x 2160, 60Hz).
• Your PC display screen might appear dierent depending on the manufacturer (and your particular version of Windows).
• Check your PC instruction book for information about connecting your PC to a display.
• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In some cases,
abnormal signals (such as stripes) might appear on the screen when the PC power is turned o (or if the PC is disconnected).
If so, press the [INPUT] button to enter the video mode. Also, make sure that the PC is connected.
• When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
• The display settings table complies to the IBM/VESA standards, and based on the analog input.
• The DVI support mode is regarded as same to the PC support mode.
• The best timing for the vertical frequency to each mode is 60Hz.
43BDL3017P/50BDL3017P/55BDL3017P
24
8. Pixel Defect Policy
We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst
practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD-
displays are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips
guarantees that any Plasma- & LCD- displays with an unacceptable number of defects will be repaired during the warranty
period in line with your local guarantee conditions.
This notice explains the dierent types of pixel defects and denes the acceptable defect level for the LCD screen. In order to
qualify for repair under warranty, the number of pixel defects must exceed a certain level as shown in the reference table. If
the LCD screen is within specication a warranty exchange / claim back will be refused. Additionally, because some types or
combinations of pixel defects are more noticeable than others, Philips sets even higher quality standards for those.
8.1. Pixels and Sub-Pixels
subpixel
pixel
A pixel, or picture element, is composed of three sub-pixels in the primary colors
of red, green and blue. Many pixels together form an image. When all sub-pixels
of a pixel are lit, the three colored sub-pixels together appear as a single white
pixel. When all are dark, the three colored sub-pixels together appear as a single
black pixel. Other combinations of lit and dark sub-pixels appear as single pixels
of other colors.
8.2. Types of Pixel Defects + Dot Definition
Pixel and sub-pixel defects appear on the screen in dierent ways. There are three categories of pixel defects and several types
of sub-pixel defects within each category.
Dot denition = What is a defective “Dot”? :
One or more defective, adjacent sub-pixel are dened as one “dot”. The no. of defective sub-pixels are not relevant to dene a
defective dot. This means that a defective dot can consist of one, two or three defective sub-pixels which can be dark or lit.
RR G B
One dot = One Pixel; consists of three sub-pixels of Red, Green, and Blue.
8.3. Bright Dot Defects
Bright dot defects appear as pixels or sub-pixels that are always lit or “on”. These are the examples of bright dot defects:
One lit red, green or blue sub pixel Two adjacent lit sub pixels:
Red + Blue = Purple
Red + Green = Yellow
Green + Blue = Cyan (Light Blue)
Three adjacent lit sub pixels (one white
pixel)
43BDL3017P/50BDL3017P/55BDL3017P
25
8.4. Dark Dot Defects
Black dot defects appear as pixels or sub-pixels that are always dark or “o”. These are the examples of black dot defects:
One dark dot Two adjacent dark dots = 1 pair of dark
dots
Two dark dots, specications denes
the minimum distance between dark
dots
8.5. Proximity of Pixel Defects
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also
species tolerances for the proximity of pixel defects. In the table below you can nd specications about:
• Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)
• Minimum distance between dark dots
• Total no. of all defective dots
8.6. Pixel Defect Tolerances
In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD-
display must have pixel or sub-pixel defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT ACCEPTABLE LEVEL
1 lit sub pixel 2
BLACK DOT EFFECT ACCEPTABLE LEVEL
1 dark sub pixel 10
TOTAL DOT DEFECTS OF ALL TYPES 12
NOTE: * 1 or 2 adjacent sub pixel defects = 1 dot defect
8.7. MURA
Dark spots or patches may occasionally appear on some liquid crystal display (LCD) panels. This is known within the industry
as Mura, which is a Japanese term for “unevenness.” It is used to describe an irregular pattern or area in which uneven screen
uniformity appears under certain conditions. Mura is a result of the deterioration of the liquid crystal alignment layer and is most
commonly caused by long-term operation under high ambient temperatures. It is an industry- wide phenomenon and Mura is
not repairable. It is also not covered by our warranty terms.
Mura has been around since the introduction of LCD technology and with screens getting bigger and in operation 24/7, many
displays are running in low light conditions. This all adds to the possibility of Mura aecting displays.
HOW TO SPOT MURA
There are many symptoms of Mura and also multiple causes. Several of these are listed below:
• Impurities or foreign particles in the crystal matrix
• Uneven distribution of LCD matrix during manufacturing
• Non-uniform luminance distribution of the backlight
• Panel assembly induced stress
• Flaws within the LCD cells
• Thermal induced stress - high temperature operation over long periods of time
43BDL3017P/50BDL3017P/55BDL3017P
26
HOW TO AVOID MURA
Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be
minimized by these methods:
• Lower the backlight brightness
• Use a screen saver
• Reduce the ambient temperature around the unit
9. Cleaning and Troubleshooting
9.1. Cleaning
Caution When Using the Display
• Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very
hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries
may occur if any body parts are brought too close. Placing any object near the top of the display could also result in heat
related damage to the object as well as the display itself.
• Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the
cables and thus cause re or electric shock.
• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or
maintenance procedure.
Front Panel Cleaning Instructions
• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a soft, lint-free
cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess
liquid. Wipe the surface of the display to remove dirt. Then use a dry cloth of the same type to dry.
• Do not scratch or hit the surface of the panel with ngers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners.
Cabinet Cleaning Instructions
• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.
• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove as much
moisture as possible. Wipe the cabinet. Use another dry cloth to wipe over until the surface is dry.
• Do not use solution that contains oil to clean the plastic parts. Such product damage the plastic parts and void the
warranty.
• Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside
the unit, operating problems, electrical and shock hazards may result.
• Do not scratch or hit the cabinet with ngers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.
• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
43BDL3017P/50BDL3017P/55BDL3017P
27
9.2. Troubleshooting
Symptom Possible Cause Remedy
No picture is displayed 1. The power cord is disconnected.
2. The main power switch on the back
of the display is not switched on.
3. The selected input has no connection.
4. The display is in standby mode.
1. Plug in the power cord.
2. Make sure the power switch is
switched on.
3. Connect a signal connection to the
display.
Interference displayed on the display or
audible noise is heard
Caused by surrounding electrical
appliances or uorescent lights.
Move the display to another location to
see if the interference is reduced.
Color is abnormal The signal cable is not connected
properly.
Make sure that the signal cable is
attached rmly to the back of the display.
Picture is distorted with abnormal
patterns
1. The signal cable is not connected
properly.
2. The input signal is beyond the
capabilities of the display.
1. Make sure that the signal cable is
attached rmly.
2. Check the video signal source to see if
it is beyond the range of the display.
Please verify its specications with
this display’s specication section.
Display image doesn’t ll up the full size
of the screen
1. The zoom mode is not set correctly.
2. Scan Mode may be set incorrectly to
underscan.
3. If the image exceeds the screen size,
Scan Mode may need to be set to
Underscan.
Use the Zoom mode or Custom zoom
function in the Screen menu to ne tune
display geometry and time frequency
parameter.
Can hear sound, but no picture Source signal cable is connected
improperly.
Make sure that both video inputs and
sound inputs are correctly connected.
Can see picture but no sound is heard 1. Source signal cable is connected
improperly.
2. Volume is turned all the way down.
3. {Mute} is turned on.
4. No external speaker connected.
1. Make sure that both video inputs and
sound inputs are correctly connected.
2. Press [ ] or [ ] button to hear
sound.
3. Switch MUTE o by using the [ ]
button.
4. Connect external speakers and adjust
the volume to a suitable level.
Some picture elements do not light
up
Some pixels of the display are o. This display is manufactured using
an extremely high level of precision
technology: however, sometimes some
pixels of the display may not display.
This is not a malfunction.
After-Images can still be seen on the
display after the display is powered o.
(Examples of still pictures include logos,
video games, computer images, and
images displayed in 4:3 normal mode)
A still picture is displayed for an over
extended period of time
Do not allow a still image to be displayed
for an extended period of time as this
can cause a permanent after-image to
remain on the display.
43BDL3017P/50BDL3017P/55BDL3017P
28
10. Warranty Statement
Warranty period for PHILIPS signage display is listed as below, for areas not covered in this table, please follow their warranty
statement.
Region Warranty Period
USA, Canada 3 years
China 1 year
Asia Pacic 3 years
Europe 3 years
Brazil 3 years
43BDL3017P/50BDL3017P/55BDL3017P
29
11. Technical Specifications
Display:
Item Specications
43BDL3017P 50BDL3017P 55BDL3017P
Screen Size (Active Area) 108 cm / 42.5 inch 125.7 cm / 49.5 inch 138.7 cm / 54.6 inch
Aspect Ratio 16:9 16:9 16:9
Number of pixels 3840 (H) x 2160 (V) 3840 (H) x 2160 (V) 3840 (H) x 2160 (V)
Pixel pitch 0.2451 (H) x 0.2451 (V) [mm] 0.2854 (H) x 0.2854 (V) [mm] 0.315 (H) x 0.315 (V) [mm]
Displayable colors 8 bits+FRC, 1.07 Billion colors 8 bits+FRC, 1.07 Billion colors 8 bits+FRC, 1.07 Billion colors
Brightness (typical) 700 cd/m2 700 cd/m2 700 cd/m2
Contrast ratio (typical) 1200:1 4000:1 5000:1
Viewing angle 178 degrees 178 degrees 178 degrees
In/Out Terminals:
Item Specications
Speaker Output Internal Speakers 10W (L) + 10W (R) [RMS]/8Ω
82 dB/W/M/160 Hz - 13 KHz
Audio Output 3.5mm phone jack x 1 0.5V [rms] (Normal) / 2 Channel (L+R)
Audio Input 3.5mm phone jack x 1 0.5V [rms] (Normal) / 2 Channel (L+R)
RS232 2.5mm Phone jack x 2 RS232 in/RS232 out
RJ-45 RJ-45 Jack x 1 (8 pin) 10/100 LAN Port
HDMI Input /Output HDMI Jack x 3 (in) / x1(out)
(Type A) (19 pin)
Digital RGB: TMDS (Video + Audio)
MAX:
Video - 720p, 1080p, 3840 x 2160/60 Hz
Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
Displayport in/out Displayport Jack x 2
(20 pin)
Digital RGB: TMDS (Video + Audio)
MAX: Video - 720p, 1080p, 3840 x 2160/60 Hz
Audio - 48 KHz / 2 Channel (L+R)
Supports LPCM only
DVI-I Input DVI-I Jack Digital RGB: TMDS (Video)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ),
MAX: 1920 x 1080/60 Hz (WUXGA)
IR Input/Output 3.5mm x 2 IR pass through
SD card Micro SD card Support to 1TB
USB Input USB x 1 (Type A) USB 2.0, Multimedia play and service port
43BDL3017P/50BDL3017P/55BDL3017P
30
General:
Item Specications
43BDL3017P 50BDL3017P 55BDL3017P
Power Input 100 - 240V~, 50/60Hz 100 - 240V~, 50/60Hz 100 - 240V~, 50/60Hz
Power Consumption (Max) 240 W 260 W 296 W
Power Consumption (typ.) 100 W 110 W 148 W
Power Consumption (Standby & O) <0.5 W <0.5 W <0.5 W
Dimensions [W x H x D] 973 x 561.2 x 76.8 mm 1128.4 x 649 x 76.8 mm 1241.8 x 712.6 x 76.8mm
Weight 13.94 Kg 17.3 Kg 20.66 Kg
Gross Weight 17.1 Kg 21.1 Kg 26.6 Kg
Energy Eciency Class B B B
Visible Screen Size 1079.5 mm / 42.5 inch 1257.3 mm / 49.5 inch 1387 mm / 54.6 inch
On Mode Power Consumption (W) 95 W 124 W 151 W
Annual Energy Consumption (kWh) 139 kWh 181 kWh 220 kWh
Standby mode Power Consumption (W) 0.5 W 0.5 W 0.5 W
O Mode Power Consumption (W) 0.3 W 0.3 W 0.3 W
Display Resolution (Pixels) 3840 x 2160 3840 x 2160 3840 x 2160
Environmental Condition:
Item Specications
Temperature Operational 0 ~ 40°C
Storage -20 ~ 60°C
Humidity Operational 20 ~ 80% RH (No condensation)
Storage 5 ~ 95% RH (No condensation)
Altitude Operational 0 ~ 3,000 m
Storage / Shipment 0 ~ 9,000 m
2021 © TOP Victory Investments Ltd. All rights reserved.
This product has been manufactured by and is sold under
the responsibility of Top Victory Investments Ltd., and Top
Victory Investments Ltd. is the warrantor in relation to this
product. Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used
under license.
Specications are subject to change without notice.
Version:V1.00 2021-03-15