Table of Contents
Philips AD7050W/10 User Manual
Displayed below is the user manual for AD7050W/10 by Philips which is a product in the Loudspeakers category. This manual has pages.
Related Manuals
www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
AD7050W
Question?
Contact
Philips
1EN
Contents
1 Important 2
Safety 2
Notice 3
2 Your Entertainment System 5
Introduction 5
What's in the box 5
What else you need 5
Overview of the main unit 6
Get started to use AirPlay 6
3 Prepare 7
Connect power 7
Turn AD7050W on 7
4 Connect to your home Wi-Fi
network for AirPlay 8
Method 1: Use iOS5 Wi-Fi network
login sharing 8
Method 2: Connect to a WPS router 9
Method 3: Connect to a non-WPS
Wi-Fi router 10
5 Play 18
Stream audio from your iTunes music
library to AD7050W 18
Use advanced sound settings 20
Play/charge your iPod/iPhone/iPad
through USB socket 20
Play from an external device 21
6 Updatermware 22
Download the update le 22
Update from the conguration page 22
7 Product information 24
Specications 24
8 Troubleshooting 25
Contents
2EN
1 Important
Safety
Information for Europe:
Know these safety symbols
The 'exclamation mark' calls attention to
features for which you should carefully
read the supplied literature to prevent
operating and maintenance problems.
The 'lightening bolt' symbol indicates
uninsulated components within the product
that can cause an electric shock.
To reduce the risk of re or electric shock,
do not expose the product to rain or
moisture and do not place any objects lled
with liquids, such as vases, on the product.
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this product near water.
f Clean only with dry cloth.
g Do not block any ventilation
openings. Install in accordance with
the manufacturer's instructions.
h Do not remove the casing of this product.
i Do not expose the product to dripping
/ splashing water, rain or high humidity.
j Keep this product away from direct
sunlight,nakedamesorheat.
k Do not install near any heat
sources such as radiators, heat
registers, stoves, or other electrical
equipment(includingampliers).
l Do not place any other electrical
equipment on the product.
m Do not place any sources of
danger on the product (e.g. objects
containingliquids,burningcandles).
n Where the mains plug or an appliance
coupler is used as the disconnect
device, the disconnect device
shall remain readily operable.
Warning
•Never remove the casing of this apparatus.
•Never lubricate any part of this apparatus.
•Never place this apparatus on other electrical
equipment.
•Keep this apparatus away from direct sunlight, naked
ames or heat.
•Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect this apparatus from
the power.
Risk of overheating! Never install this
apparatus in a conned space. Always
leave a space of at least four inches around
this apparatus for ventilation. Ensure
curtains or other objects never cover
the ventilation slots on this apparatus.
3EN
Notice
Hereby, WOOX Innovations declares
that this product is in compliance with
the essential requirements and other
relevant provisions of Directive 1999/5/
EC. You can nd the Declaration of
Conformity on www.philips.com/support.
Any changes or modications made to this
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used by WOOX Innovations Limited
under license from Koninklijke Philips N.V.”
Specications are subject to change without
notice. WOOX reserves the right to change
products at any time without being obliged
to adjust earlier supplies accordingly.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin
symbol is attached to a product it
means that the product is covered by
the European Directive 2002/96/EC.
Please inform yourself about the
local separate collection system for
electrical and electronic products.
Please act according to your local rules and
do not dispose of your old products with
your normal household waste. Correct
disposal of your old product helps to
prevent potential negative consequences
for the environment and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy
to separate into three materials: cardboard
(box), polystyrene foam (buffer) and
polyethylene (bags, protective foam sheet.)
Your system consists of materials which
can be recycled and reused if disassembled
by a specialized company. Please observe
the local regulations regarding the
disposal of packaging materials, exhausted
batteries and old equipment.
“Made for iPod,” “Made for iPhone,” and
“Made for iPad” mean that an electronic
accessory has been designed to connect
specically to iPod, iPhone, or iPad, respectively,
and has been certied by the developer to
meet Apple performance standards. Apple
is not responsible for the operation of this
device or its compliance with safety and
regulatory standards. Please note that the
use of this accessory with iPod, iPhone, or
iPad may affect wireless performance.
AirPlay, iPod, and iPhone are trademarks of
Apple Inc., registered in the U.S. and other
countries. iPad is a trademark of Apple Inc.
Class II equipment symbol:
4EN
CLASS II apparatus with double insulation,
and no protective earth provided.
Note
•The type plate is located on the bottom of the
apparatus.
5EN
2 Your
Entertainment
System
Congratulations on your purchase, and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
If you contact Philips, you will be asked
for the model and serial number of
this apparatus. The model number and
serial number are on the bottom of the
apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Introduction
Apple AirPlay technology enables you to
play your iTunes music library, hosted on a
Mac, PC, iPhone, iPod touch, or iPad on any
AirPlay-enabled device (for example, your
AD7050W) connected to the Wi-Fi network.
With an AirPlay-enabled device (for
example, your AD7050W), you can:
• stream audio from your iTunes music
library to any room in your house
• choose which AirPlay-enabled
devices you want to play music
on (if you have more than one
such devices in your house)
• stream audio to multiple AirPlay-
enabled devices at the same
time (from the iTunes music
library on your PC/Mac only)
Tip
•Please visit www.philips.com/welcome for information
about more Philips AirPlay-enabled devices.
With AD7050W, you can also:
• charge your iPod/iPhone/iPad through
the USB socket with an Apple USB
cable (not supplied).
• play your iTunes music library on
your iPod/iPhone/iPad through the
USB socket directly while charging.
• play music from other audio devices
through the MP3-LINK socket.
What's in the box
Check and identify the contents
of your package:
• Main unit (with a built-in Wi-Fi
module)
• 1 x AC power adapter
• 1 x MP3 link cable
• User manual (on CD-ROM)
• Quick start guide
What else you need
To stream audio wirelessly by AirPlay, you need:
• A Wi-Fi certied router
• A host for your iTunes music library,
for example, an iPod touch/iPhone/
iPad installed with iOS 4.3.3 (or
later) or a Wi-Fi enabled PC/Mac
installed with iTunes 10.2.2 (or later)
Your AD7050W should be connected to
the same local network as your iTunes
host device through the Wi-Fi router.
List of compatible iTunes host devices
for AirPlay
In terms of AirPlay, AD7050W
is compatible with:
• a Wi-Fi enabled PC/Mac installed with
iTunes 10.2.2 (or later); and
6EN
• the following iPod/iPhone/iPad models
installed with iOS 4.3.3 (or later):
Made for
• iPhone 5
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPad (4th generation)
• iPad mini
• iPad (3rd generation)
• iPad 2
• iPad
• iPod touch (5th generation)
• iPod touch (4th generation)
• iPod touch (3rd generation)
Overview of the main unit
a VOL +/-
• Adjust volume.
• Press and hold both buttons
to reset the unit.
b POWER
• Press to turn the unit on.
• In power-on mode, press and
hold to turn the unit off.
• In power-on mode, press to
turn the bottom light on/off.
power
VOL
c WI-FI SETUP button/indicator
• Connect the unit to a Wi-Fi network.
• Show the Wi-Fi connection
status of the unit.
d MP3-LINK
• Connect an external audio player
through the supplied MP3 link cable.
e USB
• Connect an iPod/iPhone/iPad through
an Apple USB cable (not supplied).
f DC IN
• Connect the power adaptor.
g Bottom light
Get started to use AirPlay
To get started with AirPlay, you need to:
1 Upgrade your iPod touch/iPhone/iPad to
the latest iOS version (iOS 4.3 or later).
• Or install the latest version of iTunes
(iTunes 10 or later) on your PC/Mac.
2 Connect power to AD7050W, then turn it
on (see 'Prepare' on page 7).
3 Connect AD7050W to your existing home
Wi-Fi network (see 'Connect to your
home Wi-Fi network for AirPlay' on page
8).
4 Make sure that your iPod touch/iPhone/
iPad or PC/Mac are also connected to the
same Wi-Fi network.
7EN
3 Prepare
Always follow the instructions in
this chapter in sequence.
Connect power
Caution
•Risk of product damage! Make sure that the power
supply voltage matches the voltage printed on the
bottom of the unit.
•Risk of electric shock! When you unplug the AC
adaptor, always pull the plug from the socket. Never
pull the cord.
•Before you connect the AC adaptor, make sure that you
have completed all the other connections.
• Connect the AC power cord to
• the DC IN socket on the back of the
unit.
• the wall power socket.
Turn AD7050W on
1 Press on the back to turn the unit on.
2 Wait for successful boot-up of the unit.
» The boot-up takes up to 25 seconds.
» During boot-up, the Wi-Fi SETUP
indicator on the back of the unit blinks
yellow.
» After boot-up, the Wi-Fi SETUP
indicator turns solid yellow.
• To turn the unit off, press and hold .
• To turn the unit on again, press and hold
once more.
Tip
•If the unit stays idle for more than 30 minutes, it turns
off automatically.
•In power-on mode, you can press to turn on or off
the LED light at the bottom of the unit.
8EN
4 Connect to
your home Wi-
Fi network for
AirPlay
To connect AD7050W to your existing
home Wi-Fi network, you need to apply
your home Wi-Fi settings to AD7050W.
Choose your best setup method based
on the preconditions listed below.
Precondition Setup method
You have an iPod
touch/iPhone/
iPad upgraded to
iOS 5.0 or later.
Choose method 1
(recommended) (see
'Method 1: Use iOS5
Wi-Fi network login
sharing' on page 8).
Your Wi-Fi router is
enabled with WPS
(Wi-Fi Protected
Setup) and supports
PBC (Push Button
Connection).
Choose method
2 (see 'Method 2:
Connect to a WPS
router' on page 9).
You have a Wi-Fi
enabled device with
an Internet browser,
such as an iPod touch/
iPhone/iPad or a Wi-Fi
enabled PC/Mac.
Choose method
3 (see 'Method 3:
Connect to a non-
WPS Wi-Fi router'
on page 10).
Before connection of AD7050W to you
home Wi-Fi network, make sure that:
a your Wi-Fi router is powered
on and working properly.
b AD7050W has been powered on
and booted up successfully (see
'Turn AD7050W on' on page 7).
Once connected successfully, AD7050W
will remember your home Wi-Fi settings.
Then you can enjoy AirPlay whenever
AD7050W is powered on and connected
to your home Wi-Fi network automatically.
Method 1: Use iOS5 Wi-Fi
network login sharing
1 Connect your iPod touch/iPhone/iPad to
your home Wi-Fi network.
2 Connect an Apple USB cable (not
supplied) to:
• the USB socket on the back of
AD7050W.
• the dock connector on
your iPod/iPhone/iPad.
9EN
3 Press WIFI SETUP on the back of
AD7050W.
» The following dialog box is displayed.
4 Tap ALLOW (allow) to share your Wi-Fi
settings with AD7050W.
» After a while, the indicator on the back
of AD7050W turns solid green, and
the unit beeps.
» AD7050W is connected to your
existing home Wi-Fi network
successfully.
Method 2: Connect to a WPS
router
Note
•Before you press any button on AD7050W, make sure
that AD7050W has been booted up successfully (see
'Turn AD7050W on' on page 7).
1 Press the WPS button on your home Wi-Fi
router.
2 Shortly after step 1, press Wi-Fi SETUP on
the back of AD7050W.
» The Wi-Fi SETUP indicator blinks red,
yellow and green alternately.
» Within 2 minutes, the WI-FI SETUP
indicator turns solid green, and the unit
beeps.
» AD7050W is connected to your home
Wi-Fi network successfully.
WPS
10 EN
Tip
•For some Wi-Fi routers, you may need to hold the
WPS button for Wi-Fi connection or enable the WPS
PBC function from the router conguration pages. See
the user manuals of the specic routers for details.
•If the Wi-Fi SETUP indicator on AD7050W does not
turn solid green, it means that the Wi-Fi connection
has failed. Please wait for 2 minutes and try again. If the
problem remains, try to set up the Wi-Fi connection
manually (see 'Method 3: Connect to a non-WPS Wi-Fi
router' on page 10).
•If the Wi-Fi connection fails again, restart AD7050W,
and then try again.
Method 3: Connect to a non-
WPS Wi-Fi router
Note
•You can also follow the procedures below to connect
AD7050W to a WPS router manually.
To connect AD7050W to a Wi-Fi router
manually, you need access to AD7050W's
built-in conguration web page for change of
its internal Wi-Fi settings. To do so, you need a
Wi-Fi enabled device with an Internet browser
for temporary Wi-Fi connection to AD7050W.
The Wi-Fi enabled device can be an iPod touch/
iPhone/iPad or a Wi-Fi enabled PC/Mac.
Follow the sequence below for connection
of AD7050W to a non-WPS Wi-Fi router.
1 Collect settings of your home Wi-Fi router
and write down on paper for use during
AD7050W Wi-Fi setup (see 'Collect
settings of your home Wi-Fi router' on
page 10).
2 Make sure that AD7050W is in Assisted
Wi-Fi Setup mode. If not, switch
AD7050W to Assisted Wi-Fi Setup mode
(see 'Switch AD7050W to Assisted Wi-Fi
Setup mode' on page 11).
» A new Wi-Fi network created by
AD7050W will appear, with the
network name (SSID) of Philips
AD7050W.
3 Connect your Wi-Fi enabled device to the
newly created Wi-Fi network temporarily
(see 'Connect your Wi-Fi enabled device
to the newly created Wi-Fi network' on
page 11).
4 Open the built-in web page of AD7050W
with the Internet Browser of your Wi-Fi
enabled device (see 'Open the built-in web
page of AD7050W' on page 13).
5 Change the internal Wi-Fi settings of
AD7050W based on the settings you
wrote on paper at step 1 (see 'Change the
internal Wi-Fi settings of AD7050W' on
page 14).
6 Restore your Wi-Fi enabled device back
to your existing home Wi-Fi settings (see
'Restore your Wi-Fi enabled device back
to your existing home Wi-Fi setting' on
page 16).
Collect settings of your home Wi-Fi
router
Note
•Always consult the user manual of your home Wi-Fi
router for detailed instructions.
11EN
1 Connect your Wi-Fi enabled device to
your existing home Wi-Fi network.
2 Launch the Internet browser (for example,
Apple Safari or Microsoft Internet
Explorer) on your Wi-Fi enabled device.
3 Open the conguration page of your
home Wi-Fi router.
4 Find the Wi-Fi settings tab and write down
the following information on paper:
A Network name (SSID)
B Wi-Fi security mode (usually WPA or
WPA2 if enabled)
C Wi-Fi password (if Wi-Fi security is
enabled)
D DHCP mode (enabled or disabled)
E Static IP address settings (if DHCP
mode is disabled)
Switch AD7050W to Assisted Wi-Fi
Setup mode
Note
•Before you press any button on AD7050W, make sure
that AD7050W has been booted up successfully (see
'Turn AD7050W on' on page 7).
• Press and hold Wi-Fi SETUP on the back
of the device.
» The Wi-Fi SETUP indicator blinks
yellow and green.
» A new Wi-Fi network created by
AD7050W will appear, with the
network name (SSID) of Philips
AD7050W.
» It may take up to 30 seconds for
successful creation of this new Wi-Fi
network.
Note
•After you nish manual Wi-Fi setup for AD7050W,
the new Wi-Fi network created by AD7050W will
disappear.
•If you fail to enter Assisted Wi-Fi Setup mode, power
off AD7050W and power on it, then try again after
successful boot-up.
•Make sure that there are no other Philips AirPlay-
enabled devices in Assisted Wi-Fi Setup mode at the
same time. Multiple Wi-Fi networks created this way
may interfere with each other.
Connect your Wi-Fi enabled device to
the newly created Wi-Fi network
The new Wi-Fi network created by
AD7050W only allows access of one Wi-
Fi enabled device. To avoid interference
from any other Wi-Fi devices, you are
recommended to temporarily disable the
Wi-Fi function on your other Wi-Fi devices.
Option 1: Use your iPod touch/iPhone/iPad
1 Select Settings -> Wi-Fi on your iPod
touch/iPhone/iPad.
12 EN
2 Select Philips AD7050W from the list of
available networks.
Philips AD7050W
3 Wait until successful Wi-Fi connection on
your iPod touch/iPhone/iPad.
» is displayed at the upper left corner
of your iPod touch/iPhone/iPad.
Tip
•If Philips AD7050W is not in the list, try to scan the
available Wi-Fi networks again.
Option 2: Use your Wi-Fi enabled PC/Mac
Note
•See the user manual of your PC/Mac for how to
connect your PC/Mac to a Wi-Fi network.
•During Wi-Fi network connection, do not connect any
network cable to your PC/Mac.
1 Open the Wi-Fi setup tool or control
panel on your PC/Mac.
2 Scan the available Wi-Fi networks.
3 Select Philips AD7050W from the list of
available networks.
13EN
4 Wait until successful Wi-Fi connection on
your PC/Mac.
Tip
•If Philips AD7050W is not in the list, try to scan the
available Wi-Fi networks again.
Open the built-in web page of
AD7050W
1 Launch Apple Safari browser or any other
Internet browser on your Wi-Fi enabled
device.
2 Type in 192.168.1.1 at the browser
address bar and conrm.
» The AD7050W conguration web
page is displayed.
If you use Safari on your Wi-Fi enabled
PC/Mac, you can also select 'Philips
AD7050W XXX' from the Bonjour
pull-down list to enter the AD7050W
congurationwebpagedirectly.
1 Click -> Preferences.
» The Bookmarks menu is displayed.
192.168.1.1
14 EN
2 Tick Include Bonjour for Bookmarks bar.
3 Select 'Philips AD7050W XXX' from
the Bonjour pull-down list shown at the
bookmarks bar.
» The AD7050W conguration web
page is displayed.
Change the internal Wi-Fi settings of
AD7050W
Note
•Make sure that the settings on the conguration web
page match your home Wi-Fi network settings that you
wrote on paper.
On the conguration web page
of AD7050W, you can
• rename your AD7050W, and
• congure the Wi-Fi settings of AD7050W.
Change the device name
1 Rename your AD7050W in the box
behind Philips Fidelio device name.
2 Click or tap Rename.
ConguretheWi-Fisettings
1 Click or tap behind Select Option.
» The list of available Wi-Fi networks is
displayed.
Philips Fidelio device name
15EN
2 Select your Wi-Fi network from the list.
Select Option
Your Wi-Fi Network
3 Enter the password for your Wi-Fi network
on the red box, and then click or tap
Apply.
4 Click or tap OK.
16 EN
» After a while, the indicator on the back
of AD7050W turns solid green, and
the unit beeps.
» AD7050W is connected to your
existing home Wi-Fi network
successfully.
Note
•If the WI-FI SETUP indicator on AD7050W does not
turn solid green, it means that the Wi-Fi connection
has failed. Please power off both your Wi-Fi router
and AD7050W and then power on them again to see
whether AD7050W can be connected to your home
Wi-Fi network. If the problem remains, try the above
procedures again.
•After you nish the above changes or power-off and
power-on of AD7050W, the new Wi-Fi network
created by AD7050W will disappear.
Tip
•If you like, you can change the name of your AD7050W
in Advanced settings -> AirPlay Device Name on the
AD7050W conguration web page. This is helpful when
you have multiple Philips AirPlay-enabled devices in
your house and you need to distinguish between them.
•If you want to enter the network name (SSID) manually
(for example, if you want to hide your SSID), go to
Advanced settings -> CONFIGURE MANUALLY on
the AD7050W conguration web page.
Restore your Wi-Fi enabled device
back to your existing home Wi-Fi
setting
Note
•Make sure that the settings at steps 2 to 3 below match
your home Wi-Fi network settings you wrote on paper.
1 Select Settings -> Wi-Fi on your iPod
touch/iPhone/iPad.
• Or open the list of available Wi-Fi
networks on your PC/Mac.
17EN
2 Select your network name (SSID) from the
list of available wireless networks.
3 Enter the network key if required.
4 Wait until successful Wi-Fi connection to
your home Wi-Fi network.
18 EN
5 Play
Stream audio from your
iTunes music library to
AD7050W
Note
•Make sure that your iTunes host device is connected
to the same Wi-Fi network as AD7050W. Your iTunes
device can be an iPod touch/iPhone/iPad installed with
iOS 4.3 (or later) or a Wi-Fi enabled PC/Mac installed
with iTunes 10 (or later).
•For iPhone 4S users: To ensure optimal performance
of AirPlay streaming, upgrade your iPhone 4S to iOS
5.1 or later.
Stream from your iPod touch/iPhone/
iPad
1 Launch the iPod/Music application on your
iPod touch/iPhone/iPad.
2 Tap the AirPlay icon.
3 Select Philips AD7050W XXXX (or user
customized name) from the AirPlay list.
19EN
4 Select a media le and start play.
» After a while, you will hear music from
AD7050W.
Philips AD7050W xxx
Philips AD7050W xxx
Note
•If you fail to hear music after successful setup, do one of
the following on your iPod touch/iPhone/iPad:
•(1) Disconnect and then re-connect to the same Wi-Fi
router again;
•(2) Close all applications running at the background;
•(3) Power off and then power on your iPod touch/
iPhone/iPad again.
Stream from your PC/Mac
1 Launch iTunes 10 (or a later version) on
your PC/Mac.
2 Click the AirPlay icon on the window.
20 EN
3 Select Philips AD7050W XXXX (or user
customized name) from the AirPlay list.
4 Select a media le and start play.
» After a while, you will hear music from
AD7050W.
Tip
•When you stream audio from your iTunes music library
on a PC/Mac, you can select more than one AirPlay-
enabled devices (if available) at step 3 to stream music
to all of them at the same time.
•If you are using an earlier version of iTunes, the AirPlay
icon may be instead of .
Use advanced sound settings
If your iTunes host device is an
iPod touch/iPhone/iPad:
For advanced sound settings and additional
features, you can use your iPod touch/
iPhone/iPad to download the Philips
SoundStudio application from Apple App
Store. It is a free application from Philips.
If your iTunes host device is a
Wi-Fi enabled PC/Mac:
For advanced sound settings, you can
use the equalizer available on iTunes
directly (View -> Show Equalizer).
Tip
•See the iTunes help documentation for more details.
Play/charge your iPod/iPhone/
iPad through USB socket
Note
•The USB socket is only compatible with iPod/iPhone/
iPad.
You can play or charge your iPod/iPhone/
iPad through the USB socket with an
Apple USB cable (not supplied).
21EN
• Connect an Apple USB cable (not
supplied) to:
• the USB socket on the back of
AD7050W.
• the dock connector on
your iPod/iPhone/iPad.
Compatible iPod/iPhone/iPad
The USB socket supports play and charge of
the following iPod, iPhone, and iPad models.
• iPad 2
• iPad
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
• iPod nano (2nd, 3rd, 4th, 5th, and 6th
generation)
• iPod touch (1st, 2nd, 3rd, and 4th
generation)
Play from an external device
You can also listen to an external
audio player through the unit.
1 Connect a 3.5mm audio input cable (not
supplied) to:
• the MP3 LINK socket on the back of
the unit.
• the headphone socket on an
external audio player.
2 Make sure that you have stopped AirPlay
streaming and music play through the USB
socket.
3 Start music play on the external audio
player.
» You can hear music from AD7050W.
22 EN
6 Update
firmware
Note
•You can only update the rmware from a PC/Mac.
Downloadtheupdatele
1 On your PC/Mac, go to www.philips.com/
support.
2 Enter the model number to nd the latest
rmware upgrade le available.
3 Save and unzip the upgrade le to your
hard drive.
Update from the
congurationpage
Warning
•Always connect your AD7050W to AC power for
rmware upgrade. Never power off your AD7050W
during rmware upgrade.
www.philips.com/support
XXXX
XXXX. zip
Note
•To use an Internet browser other than Apple Safari
on your PC/Mac, remember to go to the Wi-Fi router
conguration page and write down the IP address of
your AD7050W. See the user manual of your Wi-Fi
router for how to nd the IP addresses of devices
connected to the Wi-Fi router.
1 Power on AD7050W (see 'Turn
AD7050W on' on page 7).
» It takes about 25 seconds for the unit
to boot up. During boot-up, the WI-FI
SETUP indicator on the back of the
unit blinks yellow.
» After boot-up, you can hear a beep
and the WI-FI SETUP indicator turns
to solid green.
» AD7050W is connected to the last
congured Wi-Fi network automatically.
2 Make sure that AD7050W and your PC/
Mac are connected to the same Wi-Fi
router.
3 Open Apple Safari on your PC/Mac, then
select 'Philips AD7050W XXXXXX' from
the Bonjour pull-down list.
• Or open any other Internet browser
on your PC/Mac, then type in the IP
address of AD7050W (available on the
Wi-Fi router conguration page) at the
address bar.
» The AD7050W conguration web
page is displayed.
23EN
4 Follow the on-screen instructions to
complete the rmware update.
Note
•In case the rmware update fails, you can try the above
procedures again.
•After successful rmware update, if there is any
problem with the Wi-Fi connection, restart AD7050W,
and then try to set up the Wi-Fi network for
AD7050W again (see 'Connect to your home Wi-Fi
network for AirPlay' on page 8).
24 EN
7 Product
information
Note
•Product information is subject to change without prior
notice.
Specications
Amplier
Rated Output Power 2 X 20 W RMS
Frequency Response 50 Hz - 20
kHz, ±3 dB
Signal to Noise Ratio > 86 dB
MP3 Link 600 mV RMS
20 kohm
Speakers
Speaker Impedance 8 ohm
Speaker Driver 66 mm full range
Sensitivity 84 dB/m/W
Wireless
Wireless
standard
802.11b/g
Wireless
security
WPA/WPA2 (8-63 characters)
Frequency
range
2412 - 2462 MHz (CH1-
CH11) (for /79, /37, /55, /97)
2412 - 2472 MHz (CH1-
CH13) (for /12, /10, /05)
PBC (one
button push)
Ye s
General information
AC power
PHILIPS
SWITCHING POWER
SUPPLY MODEL:
EFS05001800250 CE
Input: 100 ~
240 V, 50/60
Hz 2A
Output: 18
V 2.5 A
Operation Power
Consumption
40 W
Power Consumption
in Standby Mode
< 0.5 W
Dimensions
- Main Unit (L x W x H)
358 x 137
x 203 mm
Weight
- With Packing
- Main Unit
3.05 kg
2.10 kg
25EN
8 Troubleshooting
Warning
•Never remove the casing of this apparatus.
To keep the warranty valid, never try
to repair the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome). When you contact Philips,
ensure that the apparatus is nearby and the
model number and serial number are available.
No power
•Make sure that the AC power plug of
the device is connected properly.
•Make sure that there is power at the AC
outlet.
No sound
•Adjust the volume.
•Check the Wi-Fi network connection.
Set up the network again if needed (see
'Connect to your home Wi-Fi network for
AirPlay' on page 8).
No response from the unit
•Restart AD7050W, and then set up the
Wi-Fi network for AD7050W again
(see 'Connect to your home Wi-Fi
network for AirPlay' on page 8).
•Disconnect and reconnect the AC power
plug, and then switch on the device again.
Wi-Fi network connection failed
•Check if your Wi-Fi router is Wi-
Fi 802.11b/g certied. This device
is only compatible with Wi-Fi
802.11b/g certied routers.
•If your Wi-Fi router is Wi-Fi 802.11n
certied, make sure to enable the
802.11b/g mode. AD7050W does not
support connection to routers with
802.11n only.
•This device does not support the WPS-
PIN method.
•If your Wi-Fi router supports WPS and the
WPS-PBC method but fails to connect to
AD7050W, try the manual Wi-Fi setup
method (see 'Method 3: Connect to a
non-WPS Wi-Fi router' on page 10).
•Enable SSID broadcast on the Wi-Fi router.
•Keep away from potential sources of
interference which may affect Wi-Fi signal,
such as microwave ovens.
•If you fail to use your PC for Wi-Fi network
setup, check whether your PC is using a
Wi-Fi network. You cannot use Ethernet
connection for AirPlay network setup.
•Make sure that the SSID name of your
home router consists of alphanumeric
characters, with no space or special
characters like %/#/* inserted.
•If you choose to rename the AirPlay device
'Philips AD7050W XXXX' in the setting
menu, do not use special characters or
symbols.
•For some new types of Wi-Fi routers, a
network name (SSID) may be created
automatically when you use WPS for
connection. Always change the default
network name (SSID) to a simple one that
consists of alphanumerical characters, and
also change the Wi-Fi security mode to
secure your network.
Occasional breaking of AirPlay music
streaming
Do one or all of the following:
•Move AD7050W closer to
your Wi-Fi router.
26 EN
•Remove any obstacles between AD7050W
and your Wi-Fi router.
•Avoid using Wi-Fi channel which is
overlapped by the nearby Wi-Fi network.
•Check if your network speed is fast enough
(in cases where multiple devices share the
same router, the AirPlay performance may
be affected). Turn off the other devices
connected to your home router.
•Enable the Quality of Service (QoS)
option (if available on the Wi-Fi router).
•Turn off other Wi-Fi routers.
No AirPlay icon on my iTunes host device
•Make sure that AD7050W is already
connected to your home Wi-Fi network.
•Before you open iTunes, make sure that
you have enabled Bonjour service in
your PC. Take Windows XP for example:
to enable the service, you can click
Start->Control Panel, and double-click
Administrative Tools-> Services->Bonjour
Service, then click Start followed by OK
on the pop-up menu.
•If the problem remains, try to restart
AD7050W.
AirPlay connection failed with Mac or PC
•Temporarily disable the rewall and
security software to see whether it blocks
the ports that AirPlay uses to stream
content. See the help documentation of
your rewall and security software on how
to unblock the ports used by AirPlay.
•When you use iPod Touch/iPhone/iPad/
Mac/PC for AirPlay, if the music play breaks
or stops, try to restart your iPod Touch/
iPhone/iPad, iTunes or AD7050W.
•Video streaming or FTP downloads may
overload your router and therefore may
cause interruptions during AirPlay music
play. Try to reduce the load of your router.
Specicationsaresubjecttochangewithoutnotice.
2013 © WOOX Innovations Limited. All rights reserved.
This product was brought to the market by WOOX Innovations
Limitedoroneofitsafliates,furtherreferredtointhisdocument
as WOOX Innovations, and is the manufacturer of the product.
WOOX Innovations is the warrantor in relation to the product
with which this booklet was packaged. Philips and the Philips Shield
Emblem are registered trademarks of Koninklijke Philips N.V.
AD7050W_12_UM_V3.0