Table of Contents
Philips AEA7000/10 User Manual
Displayed below is the user manual for AEA7000/10 by Philips which is a product in the Holders category. This manual has pages.
Related Manuals
www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
AEA7000
Question?
Contact
Philips
1
English
EN
Contents
1 Important 2
Safety 2
Notice 3
2 Your Wireless Microphone and
Bluetooth® Speaker 5
Introduction 5
What's in the box 5
Overview of the unit 5
3 Get started 7
Connect power 7
Switch on the Bluetooth® speaker 7
Install/replace microphone batteries 7
4 Play 9
Sing along through the wireless
microphone 9
Play from a Bluetooth® enabled device 10
Play and charge your iPad through the
dock connector directly 11
Play from an external device 12
5 Product information 13
Specications 13
6 Troubleshooting 14
Contents
2EN
1 Important
Safety
Information for Europe:
Know these safety symbols
The 'exclamation mark' calls attention to
features for which you should carefully read the
supplied literature to prevent operating and
maintenance problems.
The 'lightening bolt' symbol indicates
uninsulated components within the product
that can cause an electric shock.
Toreducetheriskofreorelectricshock,do
not expose the product to rain or moisture and
donotplaceanyobjectslledwithliquids,such
asvases,ontheproduct.
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this product near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
h Do not remove the casing of this product.
i Do not expose the product to dripping /
splashing water, rain or high humidity.
j Keep this product away from direct
sunlight, naked ames or heat.
k Do not install near any heat sources
such as radiators, heat registers, stoves,
or other electrical equipment (including
ampliers).
l Do not place any other electrical
equipment on the product.
m Do not place any sources of danger
on the product (e.g. objects containing
liquids, burning candles).
n This product may include batteries. Please
refer to safety and disposal instructions
for batteries in this user manual.
o Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Warning
•Never remove the casing of this apparatus.
•Never lubricate any part of this apparatus.
•Never place this apparatus on other electrical
equipment.
•Keepthisapparatusawayfromdirectsunlight,naked
amesorheat.
•Ensure that you always have easy access to the power
cord,plugoradaptortodisconnectthisapparatusfrom
the power.
Risk of overheating! Never install this apparatus
inaconnedspace.Alwaysleaveaspaceof
at least four inches around this apparatus for
ventilation. Ensure curtains or other objects
never cover the ventilation slots on this
apparatus.
Mains fuse
This information applies only to products with a
UK mains plug.
3
English
EN
Thisproductisttedwithanapprovedmolded
plug.Ifyoureplacethefuse,useonewith:
• theratingsshownontheplug,
• aBS1362approval,and
• the ASTA approval mark.
Contact your dealer if you are not sure about
what type of fuse to use.
Caution:ToconformwiththeEMCdirective
(2004/108/EC),donotdetachtheplugfrom
the power cord.
Notice
Anychangesormodicationsmadetothis
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authoritytooperatetheequipment.
This product complies with the radio
interferencerequirementsoftheEuropean
Community.
This product is in compliance with the essential
requirementsandotherrelevantprovisionsof
Directive 1999/5/EC.
A copy of the EC Declaration of Conformity
(DoC) is available in the packaging.
Your product is designed and manufactured
withhighqualitymaterialsandcomponents,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negativeconsequencesfortheenvironmentand
human health.
Your product contains batteries covered by
theEuropeanDirective2006/66/EC,which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negativeconsequencesfortheenvironmental
and human health.
Information about the use of batteries:
Caution
•Riskofleakage:Onlyusethespeciedtypeofbatteries.
Do not mix new and used batteries. Do not mix
different brands of batteries. Observe correct polarity.
Remove batteries from products that are not in use for
a longer period of time. Store batteries in a dry place.
•Riskofinjury:Weargloveswhenhandlingleaking
batteries. Keep batteries out of reach of children and
pets.
•Riskofexplosion:Donotshortcircuitbatteries.Do
not expose batteries to excessive heat. Do not throw
batteriesintothere.Donotdamageordisassemble
batteries. Do not recharge non-rechargeable batteries.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separateintothreematerials:cardboard(box),
polystyrene foam (buffer) and polyethylene
(bags,protectivefoamsheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
4EN
packagingmaterials,exhaustedbatteriesandold
equipment.
“MadeforiPad”meansthatanelectronic
accessory has been designed to connect
specicallytoiPad,andhasbeencertiedby
the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
the use of this accessory with iPad may affect
wireless performance.
iPadisatrademarkofAppleInc.,registeredin
the U.S. and other countries.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG,Inc.andanyuseofsuchmarksbyPhilipsis
under license.
Note
•The type plate is located on the back of the unit.
5
English
EN
2 Your Wireless
Microphone
and Bluetooth®
Speaker
Congratulationsonyourpurchase,and
welcometoPhilips!Tofullybenetfromthe
supportthatPhilipsoffers,registeryourproduct
at www.philips.com/welcome.
IfyoucontactPhilips,youwillbeaskedforthe
model and serial number of this apparatus. The
model number and serial number are on the
backoftheapparatus.Writethenumbershere:
ModelNo.__________________________
SerialNo.___________________________
Introduction
With the Philips wireless microphone and
Bluetooth®speaker,youcan:
• dock your iPad onto the speaker to
sing along with music from the app
(The Voice: On Stage) through the
wireless microphone.
With the Bluetooth®speaker,youcan:
• play music from a Bluetooth® enabled
device that supports A2DP (Advanced
AudioDistributionProle).
• charge or play music from your iPad
directly through the dock connector.
• play music from other audio devices
through the AUDIO-IN socket.
What's in the box
Check and identify the contents of your
package:
• Wireless microphone
• Bluetooth® speaker
• AC power cord
• 3 X AAA batteries
• Quick start guide
• Safety sheet
Overview of the unit
Wireless microphone
a Line out socket
• (To use the microphone separately)
connecttotheMICinputsocketofan
existing Hi-Fi system.
b Battery compartment
c OFF/ON
• Switch the microphone on or off.
d Power indicator
• Light up red when the wireless
microphone is switched on.
• Flash red when the battery level is low.
Bluetooth® speaker
d
c
b
a
6EN
a
• Turn the unit on/off.
b Power/Bluetooth® indicator
• Indicate the power/Bluetooth® status.
c -/+
• Adjust volume.
d
• (Press) pair with a Bluetooth® enabled
device that supports A2DP (Advanced
AudioDistributionProle).
• (Press and hold) pair with the wireless
microphone in case automatic pairing
fails.
e Dock for iPad
f SOFTWARE UPGRADE (not for use by
end users)
g AUDIO-IN
• Connect an external audio player
through a 3.5mm audio input cable
(not supplied).
h AC MAINS~
• AC power socket.
a
b
cde
fgh
7
English
EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Connect power
Caution
•Riskofproductdamage!Makesurethatthepower
supply voltage corresponds to the voltage printed on
the back of the unit.
•Risk of electric shock! When you unplug the AC power
cord,alwayspulltheplugfromthesocket.Neverpull
the cord.
•BeforeyouconnecttheACpowercord,makesurethat
you have completed all the other connections.
• Connect the AC power cord to
• the AC MAINS~ socket on the back
of the Bluetooth® speaker.
• the wall power socket.
Switch on the Bluetooth®
speaker
• Press on the top of the Bluetooth®
speaker.
» The power indicator lights up white.
• Toswitchtheunittostandbymode,press
on the top panel.
• Toswitchtheunitonfromstandbymode,
press again.
Tip
•Ifthespeakerstaysidleformorethan15minutes,it
switches to standby mode automatically.
Install/replace microphone
batteries
Caution
•Riskofexplosion!Keepbatteriesawayfromheat,
sunshine,orre.Neverdiscardbatteriesinre.
•Danger of explosion if batteries are incorrectly
replaced.Replaceonlywiththesameorequivalent
type.
•Batteriescontainchemicalsubstances,sotheyshould
be disposed of properly.
1 Open the battery compartment and take
out the battery cartridge.
2 Insert 3 x AAA batteries (supplied) into
the cartridge with correct polarity (+/-) as
indicated.
8EN
3 Pushbackthebatterycartridge,thenclose
the battery compartment.
Note
•If you are not going to use the microphone for a long
time,removethebatteries.
•New batteries installed in the microphone support up
to 30 hours of continuous use.
•Whenthepowerindicatorashesred,itindicatesthat
the power level is low and you need to replace the
batteries.
9
English
EN
4 Play
Sing along through the
wireless microphone
Note
•The effective operation range between the wireless
microphone and Bluetooth® speaker is approximately
10 meters (30 feet).
1 Dock your iPad onto the Bluetooth®
speaker.
» ApromptpopsupontheiPadscreen,
asking you to install the relevant app.
2 Tap YES on the prompt to install the app
(The Voice: On Stage) from Apple App
Store.
3 Aftersuccessfulinstallation,runThe Voice:
On Stage on the iPad.
4 Slide the OFF/ON switch on the wireless
microphone to the ON position.
» The Bluetooth® indicator on the
Bluetooth®speakerashesblue.
» The wireless microphone starts to
pair with the Bluetooth® speaker
automatically.
» Aftersuccessfulpairingandconnection,
the Bluetooth® indicator turns solid
blue.
5 Find and download a tutorial from The
Voice: On Stage,thentapSING for
how to sing along through the wireless
microphone and Bluetooth® speaker.
10 EN
6 Select a song from The Voice: On Stage
and sing along through the wireless
microphone.
7 Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
Tip
•Ifautomaticpairingfails,pressandhold on the
speaker for more than 10 seconds to pair the
microphone with the speaker manually.
•If the wireless microphone remains disconnected from
the Bluetooth®speakerformorethan15minutes,it
switches to standby mode automatically. To switch it
onagain,youneedtoslidetheOFF/ON switch on the
microphone to theOFF position and then slide back to
the ON position.
•You can use controls available on the app to adjust
sound effects.
•Ifyouexperiencehowlingorecho,trytoincrease
the distance between the microphone and speaker
or adjust the angle of the microphone towards the
speaker.
Play from a Bluetooth®
enabled device
Note
•The effective operation range between the Bluetooth®
speaker and your Bluetooth® enabled device is
approximately 10 meters (30 feet).
•To pair with a Bluetooth®enabledmobiledevice,make
surethat:noiPadisdocked;oryouhavestoppedmusic
play and exited The Voice: On Stage on your docked
iPad.
•Topairwithanewmobiledevice,youcanpress to
remove the existing Bluetooth® connection.
•To play from a Bluetooth®enableddevice,makesure
that you are not playing music from your iPad docked
on the Bluetooth® speaker.
1 Press on the top of the Bluetooth®
speaker.
» The Bluetooth®indicatorashesblue.
2 Enable Bluetooth® on your device
that supports A2DP (Advanced Audio
DistributionProle).
11
English
EN
3 Select 'PHILIPS_AEA7000/10' on your
Bluetooth® enabled device and if necessary
input '0000' as the paring password.
» Aftersuccessfulpairingandconnection,
the Bluetooth® indicator on the
speaker turns solid blue and the
speaker beeps twice.
4 Start music play on your Bluetooth®
enabled device.
5 Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
Play and charge your iPad
through the dock connector
directly
Compatible iPad
This unit supports play and charge of the
followingiPadmodels:
• New iPad
• iPad 2
• iPad
Load the iPad
• Dock your iPad.
To remove the iPad
• Pull the iPad out of the dock.
Listen to the iPad
1 MakesurethattheiPadhasbeenloaded
correctly.
2 Start music play on your iPad.
» The connected iPad starts to play.
3 Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
12 EN
Charge the iPad
The docked iPad begins to charge as soon as
the unit is connected to AC power.
Play from an external device
You can also listen to an external audio player
through the Bluetooth® speaker.
1 Connecta3.5mmaudiocableto:
• the AUDIO-IN socket on the back of
the Bluetooth® speaker.
• the headphone socket on an external
audio player.
2 Start music play on the external audio
player.
3 Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
AUDIO-IN
13
English
EN
5 Product
information
Note
•Product information is subject to change without prior
notice.
Specications
Amplier
Rated Output Power 2X5WRMS
Signal to Noise Ratio >70dB
Aux-in Link 600mVRMS,20
kohm
Speakers
Speaker Impedance 4 ohm
Speaker Driver 70mm full range
Sensitivity > 84dB/1m/1W
Bluetooth®
Bluetooth® version V2.1 + EDR
Frequencyband 2.402-2.480GHzISM
Band
Range 10m (free space)
General information
AC power 100-240V~;50/60
Hz
Operation Power
Consumption
20 W
Dimensions (W x H
x D)
• Speaker
• Microphone
300 x 162 x 148mm
162 x 333 x 162mm
Weight
• With Packing
• MainUnit
2.5 kg
1.5kg
14 EN
6 Troubleshooting
Warning
•Never remove the casing of this device.
Tokeepthewarrantyvalid,nevertrytorepair
the system yourself.
If you encounter problems when using this
device,checkthefollowingpointsbefore
requestingservice.Iftheproblemremains
unsolved,gotothePhilipsWebpage(www.
philips.com/support).WhenyoucontactPhilips,
make sure that the device is nearby and the
model number and serial number are available.
No power to the Bluetooth® speaker
•MakesurethattheACpowerplugofthe
device is connected properly.
•MakesurethatthereispowerattheAC
outlet.
•Asapower-savingfeature,thespeaker
switches to standby mode automatically
after staying idle for more than 15 minutes.
Switch on the speaker again (see 'Switch
on the Bluetooth® speaker' on page 7).
No power to the wireless microphone
•The batteries may be installed incorrectly
or drained. Install or replace the batteries
properly (see 'Install/replace microphone
batteries' on page 7).
•Asapower-savingfeature,themicrophone
switches to standby mode automatically
after staying disconnected from the
speaker for more than 15 minutes. To
switchitonagain,youneedtoslidethe
OFF/ON switch on the microphone to the
OFF position and then back to the ON
position.
No sound or poor sound
•Adjust volume.
•Check the Bluetooth® connection.
•Check whether you have started music
play on the connected device.
Failed to set up connection between the
microphone and speaker
• Check whether both the wireless
microphone and Bluetooth® speaker
are switched on.
• Makesurethatthewireless
microphone and Bluetooth® speaker
are within the the effective operation
range,thatis,approximately10meters
(30 feet).
• Press and hold on the top of the
Bluetooth® speaker for more than 10
seconds to set up wireless connection
manually.
Howling or echo from the wireless
microphone
• Adjust volume.
• Increase the distance between the
microphone and speaker or adjust the
angle of the microphone towards the
speaker.
No response from the Bluetooth® speaker
•Disconnect and reconnect the AC power
plug,andthenswitchonthedeviceagain.
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
AEA7000_UM_10_V1.0