Table of Contents
Philips AEA7100/17 User Manual
Displayed below is the user manual for AEA7100/17 by Philips which is a product in the Karaoke Systems category. This manual has pages.
Related Manuals
www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
AEA7100
Question?
Contact
Philips
1
English
EN
Contents
1 Important 2
Safety 2
Notice 3
2 Your Wireless Microphone and
Bluetooth® Speaker 5
Introduction 5
What’s in the box 5
Overview of the unit 5
3 Get started 7
Connect power 7
Switch on the Bluetooth® speaker 7
Install/replace microphone batteries 7
4 Play 9
Sing along through the wireless
microphone 9
Play from a Bluetooth® enabled device 10
Play and charge your iPad through the
dock connector directly 11
Play from an external device 12
5 Product information 13
Specications 13
6 Troubleshooting 14
Contents
2EN
1 Important
Safety
This ‘bolt of lightning’ indicates uninsulated
material within the device may cause an electrical
shock. For the safety of everyone in your
household, please do not remove the covering.
The ‘exclamation mark’ calls attention to
features for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
WARNING:Toreducetheriskofreorelectric
shock, the device should not be exposed to rain
ormoistureandobjectslledwithliquids,such
as vases, should not be placed on the device.
CAUTION: To prevent electric shock, fully
insert the plug. (For regions with polarized
plugs: To prevent electric shock, match wide
blade to wide slot.)
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
h Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including ampliers) that
produce heat.
i Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not t into
your outlet, consult an electrician for
replacement of the obsolete outlet.
j Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
k Only use attachments/accessories
specied by the manufacturer.
l Use only with the cart, stand, tripod,
bracket, or table specied by the
manufacturer or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
m Unplug this apparatus during lightning storms
or when unused for long periods of time.
n Refer all servicing to qualied service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
3
English
EN
o Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to
the unit:
• Install all batteries correctly, + and - as
marked on the unit.
• Remove batteries when the unit is not
used for a long time.
• Perchlorate Material-special handling
may apply. See www.dtsc.ca.gov/
hazardouswaste/perchlorate.
p Apparatus shall not be exposed to
dripping or splashing, keep it away from
direct sunlight,naked ames or heat.
Warning
•Never remove the casing of this apparatus.
•Never lubricate any part of this apparatus.
•Never place this apparatus on other electrical
equipment.
•Keep this apparatus away from direct sunlight, naked
amesorheat.
•Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect this apparatus from
the power.
Risk of overheating! Never install this apparatus
inaconnedspace.Alwaysleaveaspaceof
at least four inches around this apparatus for
ventilation. Ensure curtains or other objects
never cover the ventilation slots on this
apparatus.
Information about the use of batteries:
Caution
•Riskofleakage:Onlyusethespeciedtypeofbatteries.
Do not mix new and used batteries. Do not mix
different brands of batteries. Observe correct polarity.
Remove batteries from products that are not in use for
a longer period of time. Store batteries in a dry place.
•Risk of injury: Wear gloves when handling leaking
batteries. Keep batteries out of reach of children and
pets.
•Risk of explosion: Do not short circuit batteries. Do
not expose batteries to excessive heat. Do not throw
batteriesintothere.Donotdamageordisassemble
batteries. Do not recharge non-rechargeable batteries.
Notice
Notice of compliance
Modications
The user is cautioned that changes or
modicationsnotexpresslyapprovedbythe
party responsible for compliance could void the
user’sauthoritytooperatetheequipment.
FCC & RSS compliance statement
This device complies with Part 15 of the FCC
Rules and Industry Canada licence-exempt
RSS standard(s). Operation is subject to the
following two conditions:
a This device may not cause harmful
interference, and
b This device must accept any interference
received, including interference that may
cause undesired operation.
FCC Radiation Exposure Statement
ThisequipmentcomplieswithFCC’sandIC’s
RF radiation exposure limits set forth for an
uncontrolled environment. The antenna(s)
used for this transmitter must be installed and
operated to provide a separation distance of
at least 20 cm from all persons and must not
be collocated or operating in conjunction with
any other antenna or transmitter. Installers must
ensure that 20cm separation distance will be
maintained between the device (excluding its
handset) and users.
FCC rules
Thisequipmenthasbeentestedandfound
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residentialinstallation.Thisequipmentgenerates,
usesandcanradiateradiofrequencyenergy
and, if not installed and used in accordance with
4EN
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
Ifthisequipmentdoescauseharmful
interference to radio or television reception,
which can be determined by turning the
equipmentoffandon,theuserisencouraged
to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipmentandreceiver.
• Connecttheequipmentintoanoutleton
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Canada:
This Class B digital apparatus complies with
Canadian ICES-003.
Disposal of your old product and
batteries
Your product is designed and manufactured
withhighqualitymaterialsandcomponents,
which can be recycled and reused.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products and batteries.
The correct disposal of these products helps
preventpotentiallynegativeconsequenceson
the environment and human health.
Your product contains batteries, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negativeconsequencesontheenvironmentand
human health.
Please visit www.recycle.philips.com for
additional information on a recycling center in
your area.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
“Made for iPad” means that an electronic
accessory has been designed to connect
specicallytoiPad,andhasbeencertiedby
the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
the use of this accessory with iPad may affect
wireless performance.
iPad is a trademark of Apple Inc., registered in
the U.S. and other countries.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Philips is
under license.
Note
•The type plate is located on the back of the unit.
5
English
EN
2 Your Wireless
Microphone
and Bluetooth®
Speaker
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
If you contact Philips, you will be asked for the
model and serial number of this apparatus. The
model number and serial number are on the
back of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Introduction
With the wireless microphone and Bluetooth®
speaker, you can:
• dock your iPad onto the speaker to
sing along with music from the app
(StarMaker Karaoke + Auto-Tune®)
through the wireless microphone.
With the Bluetooth® speaker, you can:
• play music from a Bluetooth® enabled
device that supports A2DP (Advanced
AudioDistributionProle).
• charge or play music from your iPad
directly through the dock connector.
• play music from other audio devices
through the AUDIO-IN socket.
What’s in the box
Check and identify the contents of your
package:
• Wireless microphone
• Bluetooth® speaker
• AC power cord
• 3 X AAA batteries
• Quick start guide
Overview of the unit
Wireless microphone
a Line out socket
• (To use the microphone separately)
connect to the MIC input socket of an
existing Hi-Fi system.
b Battery compartment
c OFF/ON
• Switch the microphone on or off.
d Power indicator
• Light up red when the wireless
microphone is switched on.
• Flash red when the battery level is low.
d
c
b
a
6EN
Bluetooth® speaker
a Power indicator
• Indicate the power status.
b
• Turn the unit on/off.
c Bluetooth® indicator
• Indicate the Bluetooth® status.
d -/+
• Adjust volume.
e
• (Press) pair with a Bluetooth® enabled
device that supports A2DP (Advanced
AudioDistributionProle).
• (Press and hold) pair with the wireless
microphone in case automatic pairing
fails.
f Dock for iPad
g SOFTWARE UPGRADE (not for use by
end users)
h AUDIO-IN
• Connect an external audio player
through a 3.5mm audio input cable
(not supplied).
i AC MAINS~
• AC power socket.
b
ca
def
ghi
7
English
EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Connect power
Caution
•Risk of product damage! Make sure that the power
supply voltage corresponds to the voltage printed on
the back of the unit.
•Risk of electric shock! When you unplug the AC power
cord, always pull the plug from the socket. Never pull
the cord.
•Before you connect the AC power cord, make sure that
you have completed all the other connections.
• Connect the AC power cord to
• the AC MAINS~ socket on the back
of the Bluetooth® speaker.
• the wall power socket.
Switch on the Bluetooth®
speaker
• Press on the top of the Bluetooth®
speaker.
» The power indicator lights up white.
» TheBluetoothindicatorashesblue
slowly.
• To switch the unit to standby mode, press
on the top panel.
• To switch the unit on from standby mode,
press again.
Tip
•If the speaker stays idle for more than 15 minutes, it
switches to standby mode automatically.
Install/replace microphone
batteries
Caution
•Risk of explosion! Keep batteries away from heat,
sunshine,orre.Neverdiscardbatteriesinre.
•Danger of explosion if batteries are incorrectly
replaced.Replaceonlywiththesameorequivalent
type.
•Batteries contain chemical substances, so they should
be disposed of properly.
1 Open the battery compartment and take
out the battery cartridge.
2 Insert 3 x AAA batteries (supplied) into
the cartridge with correct polarity (+/-) as
indicated.
8EN
3 Push back the battery cartridge, then close
the battery compartment.
Note
•If you are not going to use the microphone for a long
time, remove the batteries.
•New batteries installed in the microphone support up
to 30 hours of continuous use.
•Whenthepowerindicatorashesred,itindicatesthat
the power level is low and you need to replace the
batteries.
9
English
EN
4 Play
Sing along through the
wireless microphone
Note
•The effective operation range between the wireless
microphone and Bluetooth® speaker is approximately
10 meters (30 feet).
1 Dock your iPad onto the Bluetooth®
speaker.
» A prompt pops up on the iPad screen,
asking you to install the relevant app.
2 Tap YES on the prompt to install the app
(StarMaker Karaoke + Auto-Tune®) from
Apple App Store.
3 After successful installation, run StarMaker
Karaoke + Auto-Tune® on the iPad.
4 Slide the OFF/ON switch on the wireless
microphone to the ON position, then
select a song from the app and tap Sing ->
RECORD.
» The wireless microphone starts to
pair with the Bluetooth® speaker
automatically.
» After successful pairing and connection,
the Bluetooth® indicator turns solid
blue.
5 Find and download a tutorial from
StarMaker Karaoke + Auto-Tune®, then
tap Sing->RECORD for how to sing along
through the wireless microphone and
Bluetooth® speaker.
6 Select a song from StarMaker Karaoke +
Auto-Tune® and sing along through the
wireless microphone.
10 EN
7 Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
Note
•If no prompt pops up on your iPad at step 1, you can
go to Settings -> General -> About -> AEA7100 ->
Find App for Accessory to install the app.
Tip
•If automatic pairing fails, press and hold on the
speaker for more than 10 seconds to pair the
microphone with the speaker manually.
•If the wireless microphone remains disconnected from
the Bluetooth® speaker for more than 15 minutes, it
switches to standby mode automatically. To switch it
on again, you need to slide the OFF/ON switch on the
microphone to theOFF position and then slide back to
the ON position.
•You can use controls available on the app to adjust
sound effects.
•If you experience howling or echo, try to increase
the distance between the microphone and speaker
or adjust the angle of the microphone towards the
speaker.
Play from a Bluetooth®
enabled device
Note
•The effective operation range between the Bluetooth®
speaker and your Bluetooth® enabled device is
approximately 10 meters (30 feet).
•To pair with a Bluetooth® enabled mobile device, make
sure that: no iPad is docked; or you have stopped music
play and exited StarMaker Karaoke + Auto-Tune® on
your docked iPad.
•To pair with a new mobile device, you can press to
remove the existing Bluetooth® connection.
•To play from a Bluetooth® enabled device, make sure
that you are not playing music from your iPad docked
on the Bluetooth® speaker.
1 Press on the top of the Bluetooth®
speaker.
» The Bluetooth®indicatorashesblue
quickly.
2 Enable Bluetooth® on your device
that supports A2DP (Advanced Audio
DistributionProle).
11
English
EN
3 Select ‘PHILIPS_AEA7100‘ on your
Bluetooth® enabled device (if necessary,
input ‘0000’ as the paring password).
» After successful pairing and connection,
the Bluetooth® indicator on the
speaker turns solid blue and the
speaker beeps twice.
4 Start music play on your Bluetooth®
enabled device.
5 Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
Play and charge your iPad
through the dock connector
directly
Compatible iPad
This unit supports play and charge of the
following iPad models:
• New iPad
• iPad 2
• iPad
Load the iPad
• Dock your iPad.
To remove the iPad
• Pull the iPad out of the dock.
Listen to the iPad
1 Make sure that the iPad has been loaded
correctly.
2 Start music play on your iPad.
» The connected iPad starts to play.
3 Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
12 EN
Charge the iPad
The docked iPad begins to charge as soon as
the unit is connected to AC power.
Play from an external device
You can also listen to an external audio player
through the Bluetooth® speaker.
1 Connect a 3.5mm audio cable to:
• the AUDIO-IN socket on the back of
the Bluetooth® speaker.
• the headphone socket on an external
audio player.
2 Start music play on the external audio
player.
3 Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
AUDIO-IN
13
English
EN
5 Product
information
Note
•Product information is subject to change without prior
notice.
Specications
Amplier
Rated Output Power 2 X 5W RMS
Signal to Noise Ratio >70dB
Aux-in Link 600 mV RMS, 20
kohm
Speakers
Speaker Impedance 4 ohm
Speaker Driver 70mm full range
Sensitivity > 84dB/1m/1W
Bluetooth®
Bluetooth® version V2.1 + EDR
Frequencyband 2.402-2.480 GHzISM
Band
Range 10m (free space)
General information
AC power 120 V~; 60 Hz
Operation Power
Consumption
20 W
Standby Power
Consumption
<0.5W
Dimensions (W x H
x D)
• Speaker
• Microphone
300 x 162 x 148mm
162 x 333 x 162mm
Weight
• Speaker
• Microphone
1.3kg
0.3kg
14 EN
6 Troubleshooting
Warning
•Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requestingservice.Iftheproblemremains
unsolved, go to the Philips Web page (www.
philips.com/support). When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
No power to the Bluetooth® speaker
•Make sure that the AC power plug of the
device is connected properly.
•Make sure that there is power at the AC
outlet.
•As a power-saving feature, the speaker
switches to standby mode automatically
after staying idle for more than 15 minutes.
Switch on the speaker again (see ‘Switch
on the Bluetooth® speaker’ on page 7).
No power to the wireless microphone
•The batteries may be installed incorrectly
or drained. Install or replace the batteries
properly (see ‘Install/replace microphone
batteries’ on page 7).
•As a power-saving feature, the microphone
switches to standby mode automatically
after staying disconnected from the
speaker for more than 15 minutes. To
switch it on again, you need to slide the
OFF/ON switch on the microphone to the
OFF position and then back to the ON
position.
No sound or poor sound
•Adjust volume.
•Check the Bluetooth® connection.
•Check whether you have started music
play on the connected device.
Failed to set up connection between the
microphone and speaker
• Check whether both the wireless
microphone and Bluetooth® speaker
are switched on.
• Make sure that the wireless
microphone and Bluetooth® speaker
are within the the effective operation
range, that is, approximately 10 meters
(30 feet).
• Press and hold on the top of the
Bluetooth® speaker for more than 10
seconds to set up wireless connection
manually.
Howling or echo from the wireless
microphone
• Adjust volume.
• Increase the distance between the
microphone and speaker or adjust the
angle of the microphone towards the
speaker.
No response from the Bluetooth® speaker
•Disconnect and reconnect the AC power
plug, and then switch on the device again.
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
AEA7100_UM_17_V1.0