Table of Contents
Philips AECS7000E/00 User Manual
Displayed below is the user manual for AECS7000E/00 by Philips which is a product in the Bluetooth Conference Speakers category. This manual has pages.
Related Manuals
www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
AECS7000E
Question?
Contact
Philips
1
English
EN
Contents
Contents
1 Important 2
Important safety information 2
Notice 2
2 Your WeCall speaker 4
Introduction 4
What’s in the box 4
Product overview 5
3 Get started 6
Charge the WeCall speaker 6
Turn on the WeCall speaker 6
Connect the WeCall speaker 6
4 Use the WeCall speaker 8
Use as a speaker phone 8
Use together with the WeCall App
(for iPhone or Android phone) 8
Use as a Bluetooth or PC speaker 9
5 Product information 11
6 Troubleshooting 12
2EN
1 Important
Important safety information
The translation of this document is for
reference only.
In the event of any inconsistency between the
English version and the translated version, the
English version takes precedence.
• Follow all instructions.
• Heed all warnings.
• Do not use this device near water.
• Clean only with dry cloth.
• Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
• Do not install near any heat sources such
as radiators, heat registers, stoves, or other
devices(includingampliers)thatproduce
heat.
• Onlyuseattachments/accessoriesspecied
by the manufacturer.
• Referallservicingtoqualiedservice
personnel. Servicing is required when the
device has been damaged in any way, such
as liquid has been spilled or objects have
fallen into the device, the device has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
• Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit,the batteries (battery pack or batteries
installed) shall not be exposed to excessive
heatsuchassunshine,reorthelike.
• CAUTION: Danger of explosion if battery
is incorrectly replaced. Replace only with
the same or equivalent type.
• The device shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on
thedevice(e.g.liquidlledobjects,lighted
candles).
Warning
•Never remove the casing of this device.
•Never lubricate any part of this device.
•Never place this device on other electrical equipment.
•Keep this device away from direct sunlight, naked
amesorheat.
About replacement of parts/accessories
Visit www.philips.com/support to order
replacement parts/accessories.
Notice
Hereby, WOOX Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions
ofDirective1999/5/EC.Youcanndthe
Declaration of Conformity on www.philips.com/
support.
Anychangesormodicationsmadetothis
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used by WOOX Innovations Limited
under license from Koninklijke Philips N.V.”
Specicationsaresubjecttochangewithout
notice. WOOX reserves the right to change
products at any time without being obliged to
adjust earlier supplies accordingly.
3
English
EN
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
Always bring your product to a professional to
remove the built-in battery.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by WOOX
Innovations is under license.
Skype is a trademark of Skype or its related
companies. Although this product has been
testedandmetourcerticationstandardsfor
audio and video quality, it is not endorsed by
Skype, Skype Communications S.a.r.l. or any of
their related companies.
No emergency calls with Skype
Skype is not a replacement for your ordinary
telephone and can’t be used for emergency
calling.
Note
•The type plate is located on the bottom of the device.
4EN
2 Your WeCall
speaker
TofullybenetfromthesupportthatPhilips
offers, register your product at www.philips.
com/welcome.
Introduction
This Bluetooth conference speaker (WeCall
speaker) allows you to:
• connect to a Bluetooth enabled
smartphone and make a mobile or
VoIP call directly through the WeCall
speaker.
• connect to a PC/Mac through the
supplied USB cable and make a
VoIP call directly through the WeCall
speaker.
• connect to a Bluetooth enabled
iPhone or Android phone and make
a conference call through the WeCall
speaker with the help of the WeCall
App.
• enjoy music from a Bluetooth-enabled
mobile device or a PC/Mac.
• enjoy music from a PC/Mac connected
through the supplied USB cable.
What’s in the box
Check and identify the following which are
included with your WeCall speaker:
• WeCall speaker
• Carrying case
• USB cable
• Printed materials
5
English
EN
Product overview
a /
• Adjust volume during a call or music
play.
b ON/OFF power switch
• Power on or off the WeCall speaker.
c CLEAR
• Remove the existing pairing
information.
d Charge indicator
• Turns red when the battery is running
low, or when you charge the WeCall
Speaker.
e Micro USB socket
• For connection with the supplied USB
cable.
a
b
c
d
e
f
i
h
g
f USB/ source switch
• Switch between the USB or Bluetooth
audio sources.
g
• Answer an incoming mobile call.
• End an ongoing mobile call.
h Source indicator
• Turns blue in Bluetooth mode.
• Turns green in USB mode.
i
• Mute the 4 built-in microphones of the
WeCall speaker during a call so that
the other party cannot hear you.
6EN
3 Get started
Caution
•Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in
sequence.
Charge the WeCall speaker
• Connect the WeCall speaker to a PC/Mac
through the supplied USB cable.
» The charge indicator turns red.
» When the WeCall speaker is fully
charged, the charge indicator turns off.
• You can also charge the WeCall speaker
through a USB power adapter (not
supplied).
Tip
•Whenthebatteryislow,thechargeindicatorashes
red.
•It takes approximately 2 hours to fully charge the
WeCall speaker.
•The fully charged WeCall speaker supports
approximately 8 hours of operation.
Turn on the WeCall speaker
• Slide the power switch to the ON position.
» In Bluetooth mode, the status indicator
turns blue.
» In USB mode, the source indicator
turns green.
• To turn off the WeCall speaker, slide the
power switch to the OFF position.
Connect the WeCall speaker
Option 1: Connect to a Bluetooth-
enabled device
You can pair the WeCall speaker with a
Bluetooth-enabled mobile device (such as
your mobile phone or tablet) or PC/Mac. Then
you can enjoy music from the WeCall speaker,
or use it as a speaker phone when you make
mobile or VoIP calls.
Note
•The effective operation range between the WeCall
speaker and your Bluetooth-enabled device is
approximately 10 meters (30 feet).
1 Slide the source switch at the bottom of
the WeCall speaker to the position.
7
English
EN
2 Enable Bluetooth on your Bluetooth-
enabled device.
3 Select ‘Philips WeCall speaker‘ on your
Bluetooth-enabled device and if necessary
input ‘0000’ as the paring password.
» Thesourceindicatorstartstoash
blue.
» After successful pairing and connection,
the source indicator turns solid blue
and the WeCall speaker beeps.
Note
•To pair with a new Bluetooth-enabled device, you can:
•1. Hold CLEAR at the bottom of the WeCall speaker
for more than 3 seconds to remove the existing
Bluetooth connection.
•2. Disable the Bluetooth function on the currently
connected device.
•The WeCall speaker can memorize up to 4 paired
devices. When you pair with another Bluetooth-enabled
device,therstmemorizeddevicewillbeoverridden.
Tip
•For PC/Mac, to ensure stable performance, the USB
connection mode is recommended.
Option 2: Connect through USB
The USB cable charges the WeCall speaker
and can also be used to connect the WeCall
speaker to a PC/Mac to enjoy music or use it as
a speaker phone when you make VoIP calls.
1 Slide the source switch at the bottom of
the WeCall speaker to the USB position.
2 Connect the WeCall speaker to a PC/Mac
through the supplied USB cable.
» The source indicator turns green.
8EN
4 Use the WeCall
speaker
Use as a speaker phone
If the WeCall speaker has been connected to
a Bluetooth-enabled mobile phone or other
devices such as a tablet or PC/Mac:
1 Make sure that you have selected the
Bluetooth source on the WeCall speaker.
2 Make a mobile or VoIP call on your mobile
phone, or a VoIP call (such as a SkypeTM
call) on your tablet or PC/Mac.
3 Use the WeCall speaker as a speaker
phone during the call.
Tip
•When there is an incoming mobile call, you can press
to answer the call.
•During a mobile call, you can press to end the call.
•During a mobile call, you can press to mute the 4
built-in microphones of the WeCall speaker so that the
other party cannot hear you.
•During a mobile or VoIP call, you can use / on
the WeCall speaker to adjust volume.
If the WeCall speaker has been connected to a
PC/Mac through the USB cable:
1 Make sure that you have selected the USB
source on the WeCall speaker.
2 Make a VoIP call (such as a SkypeTM call)
on your PC/Mac.
3 Use the WeCall speaker as a speaker
phone during the call.
Use together with the WeCall
App (for iPhone or Android
phone)
1 Download Philips WeCall to your iPhone
or Android phone.
9
English
EN
2 Set up Bluetooth connection between
the WeCall speaker and your iPhone or
Android phone (see ‘Option 1: Connect to
a Bluetooth-enabled device’ on page 6).
3 Run Philips WeCall and import meetings
from your calendar.
• The potential conference calls will be
highlighted. Choose one of them.
4 Conrmthetelephonenumberandcode.
5 Make a conference call.
Tip
•During a call, you can use / on the WeCall
speaker to adjust volume.
•During a call, you can press to mute the WeCall
speaker so that the other party cannot hear you.
•During a call, you can press to end the call.
Use as a Bluetooth or PC
speaker
1 Make sure that you have selected the
correct source on the WeCall speaker.
2 In Bluetooth mode, start audio play on the
Bluetooth-enabled device and then listen
from the WeCall speaker.
• In USB mode, start audio play on the PC/
Mac and then listen from the WeCall
speaker.
10 EN
Tip
•During audio play, you can use / on the WeCall
speaker to adjust volume.
•During audio play, you can press to mute the
WeCall speaker.
11
English
EN
5 Product
information
Amplier
Rated Output Power 2W RMS
Frequency Response 80Hz -16k Hz,
±3dB
Signal to Noise Ratio >75dB
Bluetooth
Bluetooth®
version
V2.1 + EDR
Frequency band 2.402-2.480 GHz ISM
Band
Range 10m (free space)
Speakers
Speaker Impedance 4ohm
Speaker Driver 1" speaker
Sensitivity >84dB/1W/1m
General Information
DC Power Input Input: 5 VDC, 1 A
Battery Model No.: SDL-553055-
1000mAh
Rating voltage and
capacity: 3.7VDC,
1000mAh
Dimensions
- Main Unit (w x
h x d)
110 x 28 x 110 mm
Weight
- With Packing
- Main Unit
0.33 kg
0.17 kg
12 EN
6 Troubleshooting
Warning
•Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support). When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
No power
•Check whether the WeCall speaker is
switched on (see ‘Turn on the WeCall
speaker’ on page 6).
•Recharge the WeCall speaker (see ‘Charge
the WeCall speaker’ on page 6).
No sound
•Press / on the WeCall speaker to
adjust volume.
•Adjust volume on the connected device,
such as your mobile phone, tablet, or PC/
Mac.
•Check whether you have selected the
correct source.
•Check whether the WeCall speaker is
switched on.
•Check the Bluetooth or USB connection
to the WeCall speaker.
•Check whether you have started audio
play or any call on the connected device.
Failed to set up Bluetooth connection
•Check whether the WeCall speaker is
switched on (see ‘Turn on the WeCall
speaker’ on page 6).
•Check whether you have selected the
Bluetooth source.
•Make sure that the WeCall speaker and
your Bluetooth-enabled device are within
the effective operation range, that is,
approximately 10 meters (30 feet).
•Remove any obstacle between the WeCall
speaker and your Bluetooth-enabled
device.
•Check the Bluetooth setting on your
device to be connected with the WeCall
speaker (see the user manual of the
specicdevicefordetails).
•Hold CLEAR at the bottom of the
WeCall speaker for more than 3 seconds
to reset, and then try again.
•If there is any issue with Bluetooth
connection to a PC/Mac, upgrade the
Bluetooth driver of your PC or the iOS
version of your Mac.
•Afterrst-timepairingwithaMac,
the WeCall speaker may be shown as
disconnected. It is a not a malfunction. You
just need to make VoIP calls or play music
through the WeCall speaker directly to
activate the Bluetooth connection.
2014 © WOOX Innovations Limited.
All rights reserved.
This product was brought to the market by WOOX
Innovations Limited or one of its affiliates, further referred
to in this document as WOOX Innovations, and is the
manufacturer of the product. WOOX Innovations is the
warrantor in relation to the product with which this booklet
was packaged. Philips and the Philips Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
AECS7000E_00_UM_V2.0