Table of Contents
Philips AT10/00 User Manual
Displayed below is the user manual for AT10/00 by Philips which is a product in the Portable Speakers category. This manual has pages.
Related Manuals
www.philips.com/support
AT10
User manual
Always there to help you
Register your product and get support at
Question?
Contact
Philips
1EN
Contents
1 Important 2
2 Your Portable Speaker 3
Introduction 3
What's in the box 3
Overview of the product 4
3 Get started 5
Power supply 5
Turn on or off 5
Select a source 6
4 Play 7
Play from Bluetooth-enabled devices 7
Play from an SD card or USB device 7
Listen to FM radio 8
Play from an external device 9
Adjust volume 9
5 Product information 10
Specications 10
USBplayabilityinformation 10
6 Troubleshooting 12
About Bluetooth device 12
7 Notice 13
Compliance 13
Care of the environment 13
Trademark notice 14
2EN
1 Important
Warning
• Never remove the casing of this product.
• Never lubricate any part of this product.
• Never place this product on other electrical equipment.
• Keep this product away from direct sunlight, naked
amesorheat.
• Read these instructions.
• Follow all instructions.
• Do not use this apparatus near water.
• Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
• Do not install near any heat sources such
as radiators, heat registers, stoves, or
otherapparatus(includingampliers)that
produce heat.
• Onlyuseattachments/accessoriesspecied
by the manufacturer.
• Referallservicingtoqualiedservice
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
• The battery shall not be exposed to
excessiveheatsuchassunshine,reorthe
like.
• Apparatus shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on the
apparatus(e.g.liquidlledobjects,lighted
candles).
Note
• The type plate is located on the bottom of the
apparatus.
3EN
2 Your Portable
Speaker
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this speaker, you can:
• listen to FM radio; and
• enjoy audio from SD/SDHC card, USB
devices, Bluetooth-enabled devices, and
other external devices.
What's in the box
Check and identify the contents of your
package:
• Main unit
• USB cable for charging
• Short user manual
• Safety¬iceleaet
4EN
Overview of the product
a OFF/ON switch
• Turn the product on or off.
b
• Connect a USB storage device.
c SD
• Connect an SD/SDHC card.
d AUDIO IN
• Connect an external audio device.
e -/+
• Adjust volume.
f /
• Select a track.
• Search within play.
• Tune to FM radio stations.
g /PAIRING
• In SD, USB, or Bluetooth mode, press
to pause or resume play.
• In Bluetooth mode, press and hold for
three seconds to disconnect Bluetooth
connection or enter pairing mode.
• In FM mode, press and hold for two
seconds to store FM radio stations
automatically.
• In FM mode, press to select a preset
radio station.
ab cd
l
effghij k
h MODE
• Selectarepeatorshufeplaymode.
i SOURCE
• Select an audio source.
j Display panel
• Show current status.
k FM antenna
• Improve FM radio reception.
l DC 5V
• Recharge the built-in battery.
5EN
3 Get started
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this apparatus. The
model number and serial number are on the
bottom of the apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Power supply
The product is operated on the built-in
rechargeable battery.
Note
• Rechargeable battery has a limited number of charge
cycles. Battery life and number of charge cycles vary by
use and settings.
To recharge the built-in battery:
Connect the supplied USB cable to:
• the DC 5V socket on the back of the
product.
• the USB socket on a computer.
DC 5V
Battery status Battery icon ( )
behavior
Low battery Flashing
While charging Solid on
Fully charged or
charging stopped
Off
Turn on or off
• To turn the product on, slide the OFF/ON
switch to the right.
» The product switches to the last
selected source.
• To turn the product off, slide the switch to
the left.
Switch to ECO standby mode
In SD, USB, Audio-in, or Bluetooth mode,
the product switches to ECO standby mode
automatically in the following situations:
• Music playback is stopped for 15 minutes;
• There is no Micro SD card, USB device or
Audio-in cable connected for 15 minutes;
or
• Bluetooth connection is disconnected for
15 minutes.
To return to the SD/USB/Audio-in/Bluetooth
mode:
• Press to resume playback; or
• Slide the switch to turn the product off
rst,thenturniton.
6EN
Select a source
Press SOURCE repeatedly to select an audio
source: FM tuner, USB, SD card, Bluetooth, or
AUX.
7EN
4 Play
Play from Bluetooth-enabled
devices
With this product, you can listen to audio from
Bluetooth-enabled devices.
Connect a device
Note
• Make sure that your Bluetooth device is compatible
with this product.
• Before pairing a device with this product, read its user
manual for Bluetooth compatibility.
• The product can memorize a maximum of 4 paired
devices.Thefthconnecteddevicewillreplacethe
rstone.
• Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
• Any obstacle between this product and a Bluetooth
device can reduce the operational range.
• Keep away from any other electronic device that may
cause interference.
• The operational range between this product and a
Bluetoothdeviceisapproximately10meters(30feet).
1 Press SOURCE repeatedly to select
Bluetooth source.
» [bt] ashesonthedisplay.
2 Press and hold PAIRING for 3 seconds to
enter Bluetooth pairing mode.
3 On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
(refertotheusermanualofthedevice).
4 When [Philips AT10] is displayed on
your device, select it to start pairing and
connection. If necessary, enter default
password“0000”.
» After successful pairing and connection,
the product beeps twice, and [bt]
stopsashing.
To disconnect the Bluetooth-enabled device:
• Press and hold PAIRING for 3 seconds;
• Disable Bluetooth on your device; or
• Move the device beyond the
communication range.
» The product beeps twice, and [bt]
beginstoash.
To reconnect the Bluetooth-enabled device:
• When this product enters Bluetooth
mode, it will reconnect the last connected
device automatically; or
• On your Bluetooth device, select "Philips
AT10" on your Bluetooth menu to start
connection.
To connect another Bluetooth-enabled device:
1 Press and hold PAIRING for 3 seconds to
disconnect the currently connected device.
» The product enters Bluetooth pairing
mode.
2 Connect another Bluetooth device.
Play from Bluetooth device
After successful Bluetooth connection, play
audio on the Bluetooth device.
» Audio streams from your Bluetooth
device to the product.
Play from an SD card or USB
device
Note
• Make sure that the USB storage device or SD card
contains playable audio content.
Play from an SD card
1 Press SOURCE repeatedly to select the
SD card source.
» [SD] is displayed.
8EN
2 Insert an SD/SDHC card into the card slot.
» Play starts automatically.
Play from a USB storage device
1 Press SOURCE repeatedly to select the
USB source.
» [USB] is displayed.
2 Insert the USB device into the socket.
» Play starts automatically.
Control play
In USB or SD mode, follow the instructions
below to control play.
Button Function
/ Press to skip to the previous or next
track.
Press and hold to fast forward or fast
reverse the track during playback,
then release to resume play.
Press to start, pause, or stop play.
Button Function
MODE Press repeatedly to select a play
mode:
• [ ]: Play the current track
repeatedly.
• [ALL]: Play all tracks repeatedly.
• [ ]: Play all tracks randomly.
To return to normal play mode, press
MODE repeatedly until the repeat
andshufeiconsdisappear.
Listen to FM radio
Tune to FM radio stations
Note
• Keep the product away from other electronic devices
to avoid radio interference.
1 Fully extend the FM antenna.
2 Press SOURCE repeatedly to select FM
tuner source.
3 Press and hold / for two seconds.
» The product tunes to a station with
strong reception automatically.
4 Repeat step 3 to tune to more radio
stations.
To tune to a station manually:
Press / repeatedlyuntilyoundbetter
reception.
9EN
Store FM radio stations automatically
Note
• Youcanstoreamaximumof20presetradiostations.
In FM tuner mode, press and hold for two
seconds.
» All available radio stations are stored
automatically,thentherststored
radio station is broadcast.
Tip
• You can press / to stop auto scan.
Store FM radio stations manually
(only applicable to products with the
last 10 digits of the serial number
beyond 1633077076)
Note
• Youcanstoreamaximumof20FMradiostations.
1 In FM tuner mode, tune to an FM radio
station.
2 Press MODE to activate programming
mode.
» The preset number begins to blink.
3 Press repeatedly to select a number.
4 Press MODEagaintoconrm.
5 Repeat steps 1 to 4 to store other stations.
Note
• To remove a pre-stored station, store another station
in its place.
Select a preset radio station
In tuner mode, press repeatedly to select a
preset station.
Play from an external device
With this product, you can listen to an external
audio device such as an MP3 player.
1 Press SOURCE repeatedly to select AUX
source.
2 Connect an audio input cable with a
3.5 mm connector on both ends to
• the AUDIO IN socket on the product.
• the headphone socket on an external
device.
3 Play audio on the device (refer to its user
manual).
Adjust volume
During play, press -/+ to increase or decrease
volume.
Tip
• You can press and hold -/+ for 2 seconds to increase or
decrease volume continuously.
10 EN
5 Product
information
Note
• Product information is subject to change without prior
notice.
Specications
Amplier
Total Output Power 3 W
Frequency Response 60-20000Hz,±3dB
Signal to Noise Ratio >70dBA
Aux Input 800mVRMS22kohm
Tuner (FM)
Tuning Range FM:87.5-108MHz
Tuning Grid 50KHz
- Mono, 26dB S/N
Ratio
<22 dBf
- Stereo, 46dB S/N
Ratio
>43 dBf
Search Selectivity >28 dBf
Total Harmonic
Distortion
<2%
Signal to Noise Ratio >55dB
Bluetooth
BluetoothVersion V3.0+EDR
Bluetooth Frequency
Band
2.402GHz~2.48GHz
ISM Band
Bluetooth Distance 10m(Freespace)
Speaker
Speaker Impedance 6 ohm
Speaker Driver 3" full range
Sensitivity >82dB±3dB/m/W
General information
Power Supply
(through Micro USB
socket)
5V 600mA
Built-in Battery
(Li-polymerbattery)
3.7V,1800mAh
MP3 bit rates 32-320kbps
Eco Standby Power
Consumption
<0.5W
Dimensions - Main
Unit(WxHxD)
239x104x127mm
Weight - Main Unit 0.6kg
USB playability information
Compatible USB devices:
• USBashmemory(USB2.0)
• USBashplayers(USB2.0)
• memory cards (requires an additional card
reader to work with this unit; Some multi-
cardUSBreadermaynotbesupported.)
Supported formats:
• USBormemoryleformat:FAT12,FAT16,
FAT32(sectorsize:512bytes)
• MP3bitrate(datarate):32-320Kbpsand
variable bit rate
• Directory nesting up to a maximum of
8 levels
• Number of albums/ folders: maximum 99
• Number of tracks/titles: maximum 999
• File name in Unicode UTF8 (maximum
length:16bytes)
11EN
Unsupported formats:
• Empty albums: an empty album is an album
thatdoesnotcontainMP3/WMAles,and
is not be shown in the display.
• Unsupportedleformatsareskipped.
Forexample,Worddocuments(.doc)or
MP3leswithextension.dlfareignored
and not played.
• AAC,WAV,PCMaudioles
• DRMprotectedWMAles(.wav,.m4a,
.m4p,.mp4,.aac)
• WMAlesinLosslessformat
12 EN
6 Troubleshooting
Warning
• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page
(www.philips.com/support).Whenyoucontact
Philips, make sure that the device is nearby
and the model number and serial number are
available.
No power
• Recharge the battery.
No sound or poor sound
•Adjust volume on this product.
•Adjust volume on the connected device.
•Check if you have selected the correct
audio source.
No response from the product
•Turn on the product.
•Recharge the battery.
•Turntheproductoffrst,thenturnit
on to activate the product from standby
mode.
Poor radio reception
•Increase the distance between the product
and other electrical appliances.
•Fully extend and adjust the position of the
FM antenna.
USB device not supported
•The USB device is incompatible with the
unit. Try another one.
About Bluetooth device
The audio quality is poor after connection
with a Bluetooth-enabled device.
•The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
Fail to search out AT10 on your device for
pairing.
•Press and hold PAIRING for three seconds,
and then try again.
Cannot connect with the device.
•The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.
•This product is already connected with
another Bluetooth-enabled device.
Disconnect that device and then try again.
The paired device connects and disconnects
constantly.
•The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
•For some devices, Bluetooth connection
may be deactivated automatically as a
power-saving feature. This does not indicate
any malfunction of this product.
13EN
7 Notice
Anychangesormodicationsmadetothis
device that are not expressly approved by
Gibson Innovations may void the user’s
authority to operate the equipment.
Compliance
Hereby, Gibson Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions of
Directive1999/5/EC.YoucanndtheDeclaration
of Conformity on www.philips.com/support.
Care of the environment
Disposal of your old product and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product contains
a built-in rechargeable battery covered by
EuropeanDirective2013/56/EUwhichcannot
be disposed of with normal household waste.
We strongly advise you to take your product to
anofcialcollectionpointoraPhilipsservice
centre to have a professional remove the
rechargeable battery.
Inform yourself about the local separate
collection system for electrical and electronic
products and rechargeable batteries. Follow
local rules and never dispose of the product
and rechargeable batteries with normal
household waste. Correct disposal of old
products and rechargeable batteries helps
prevent negative consequences for the
environment and human health.
Caution
• Removal of the built-in battery invalidates the warranty
and may destroy the product.
Always bring your product to a professional to
remove the built-in battery.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separateintothreematerials:cardboard(box),
polystyrenefoam(buffer)andpolyethylene
(bags,protectivefoamsheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
14 EN
Trademark notice
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Gibson
Innovations Limited is under license. Other
trademarks and trade names are those of their
respective owners.
Specifications are subject to change without notice.
2016 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson
Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used under license.
AT10_00_UM_V5.0