Philips AZ329/98 User Manual
Displayed below is the user manual for AZ329/98 by Philips which is a product in the Portable Stereo Systems category. This manual has pages.
Related Manuals
www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
AZ329/98
Question?
Contact
Philips
2EN
Contents
1 Important 3
Safety 3
Notice 3
2 Your CD Soundmachine 5
Introduction 5
What's in the box 5
Overview of the main unit 5
3 Get started 6
Connect power 6
Turn on 7
Turn off 7
4 Play 8
Play a CD 8
Play from an external device 8
Play from USB devices 8
Play from SD card 9
Play tape 9
Tune to FM radio stations 10
5 Play options 10
Control play 10
Program tracks 11
Adjust sound 11
6 Product information 11
Specications 11
Maintenance 12
7 Troubleshooting 13
3EN
1 Important
Safety
• Read these instructions.
• Follow all instructions.
• Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
• Do not install near any heat sources such
as radiators, heat registers, stoves, or
otherapparatus(includingampliers)that
produce heat.
• Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the unit.
• Onlyuseattachments/accessoriesspecied
by the manufacturer.
• Unplug this unit during lightning storms or
when unused for long periods of time.
• Recording is permissible insofar as
copyright or other rights of third parties
are not infringed upon.
• Referallservicingtoqualiedservice
personnel. Servicing is required when the
unit has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have
fallen into the apparatus, the unit has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
• Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
• Install all batteries correctly, + and - as
marked on the unit.
• Do not mix batteries (old and new or
carbonandalkaline,etc.).
• Remove batteries when the unit is not
used for a long time.
• Batteries (battery pack or batteries
installed)shallnotbeexposedtoexcessive
heatsuchassunshine,reorthelike.
• CAUTION: Danger of explosion if battery
is incorrectly replaced. Replace only with
the same or equivalent type.
• The unit shall not be exposed to dripping
or splashing.
• Do not place any sources of danger on
theunit(e.g.liquidlledobjects,lighted
candles).
• Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Warning
•Never remove the casing of this apparatus.
•Never place this apparatus on other electrical
equipment.
•Never look into the laser beam inside this apparatus.
Caution
•Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Notice
This product complies with the radio
interference requirements of the European
Community.
Anychangesormodicationsmadetothis
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
4EN
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separateintothreematerials:cardboard(box),
paperpulp(buffer)andpolyethylene(bags,
protectivefoamsheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
This apparatus includes these labels:
Class II equipment symbol
This symbol indicates that the apparatus has a
double insulation system.
The making of unauthorized copies of copy-
protected material, including computer
programs,les,broadcastsandsound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.
Windows Media and the Windows logo
are trademarks, or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
Note
•The type plate is located on the bottom of the
apparatus.
5EN
2 Your CD
Soundmachine
Introduction
With this CD Soundmachine, you can:
• listen to FM radio;
• enjoy audio from discs, tapes, USB device,
Micro SD card, and other external audio
devices;
• program the play sequence of tracks.
TheunitoffersyouDynamicBassBoost(DBB)
to enrich sound.
What's in the box
Check and identify the contents of the package:
• Main unit
• Short user manual
Overview of the main unit
a SD/USB source selector
• Press to select SD or USB source.
b
• Stop playing.
c - ALBUM +
• Skip to the previous or next album.
d /
• Skip to the previous or next track.
• Search within a track.
e OPEN•CLOSE
• Open or close the disc compartment.
f Tape controls
•
Start tape play.
• /
Fast rewind or fast forward the tape.
Stop the tape play or open the tape
door.
•
Pause tape play or pause recording.
g
• Start or pause play.
a
b
c
d
k
l
h
i
j
e
f
g
p
q
r
CD
USB/SD
FM
TAPE/OFF
AUDIO IN
m on
6EN
h PROG
• Program the play sequence of tracks.
i MODE
• Select a play mode.
j Display panel
• Display current status.
k FM antenna
• Improve FM reception.
l + TUNING -
• Tune to FM radio stations.
m
• USB socket.
n Source selector
• Select a source.
o + VOLUME -
• Adjust volume
p SD
• Micro SD card slot.
q AC~MAINS
• Power supply socket.
r AUDIO-IN
• Connect an external audio device.
3 Get started
Caution
•Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of your apparatus. The
model number and serial number are on the
bottom of your apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Connect power
The unit can be powered by either AC power
or batteries.
Option 1: AC power
Warning
•Risk of product damage! Make sure that the power
supply voltage corresponds to the voltage printed on
the back or the underside of the unit.
•Risk of electric shock! When you disconnect the AC
power, always pull the plug from the socket. Never pull
the cord.
Connect the AC power cord to the wall socket.
Tip
•To save energy, turn the unit off after use.
7EN
Option 2: Battery power
Caution
•Batteries contain chemical substances, so they should
be disposed of properly.
Note
•Batteries are not supplied with the accessories.
1 Open the battery compartment.
2 Insert 6 batteries (type: 1.5V R14/UM2/C
CELL)withcorrectpolarity(+/-)as
indicated.
3 Close the battery compartment.
AC~MAINS
Turn on
Switch the source selector on the main unit to
FM/USB/SD/CD.
» When the source selector is in the CD
position, CD is displayed.
Switch to standby mode
• The unit switches to standby mode
automatically when there is no audio
detected for over 15 minutes.
• Press to wake up the unit from
standby mode.
Turn off
Switch the source selector on the main unit to
OFF.
8EN
4 Play
Play a CD
Note
•You cannot play CDs encoded with copyright
protection technologies.
•When an audio-in cable is plugged, CD/USB playback
stops, and the unit switches to audio in mode
automatically.
You can play commercially available audio CDs:
• CD-Recordables(CD-R)
• CD-Rewritables(CD-RW)
• MP3-CDs
1 Switch the source selector to CD.
2 Open the CD compartment.
3 Insert a CD with the printed side facing up
and close the CD lid gently.
» The total number of tracks displays.
» Your CD sound machine starts to play
automatically.
• To select a track,press / .
• To pause CD play, press .
» [ ]ashes.
• To resume CD play, press again.
• To stop CD play, press .
CD
USB/SD
FM
TAPE/OFF
AUDIO IN
Play from an external device
You can also listen to an external audio device
through this unit.
1 Connect an audio cable (3.5mm, not
supplied)to:
• the AUDIO-IN socket on the unit.
• the headphone socket on an external
device.
» "Au" shows on the display.
2 Play the external device (see the device's
usermanual).
Note
•The AUDIO-IN socket is not for headphones.
•The display panel lights off when the unit plays from the
external device.
•The unit switches to Audio in mode automatically when
it plays under CD or SD/USB mode.
AUDIO-IN
9EN
Play from USB devices
Note
•Make sure that the USB device contains playable audio
content.
1 Switch the source selector to USB/SD.
2 Insert the USB device into the socket.
3 Press down SD/USB source selector to
choose USB source.
» "USB" shows on the display.
» The unit starts to play. If not, press .
CD
USB/SD
FM
TAPE/OFF
AUDIO IN
SD USB
Play from SD card
Note
•Make sure that the SD card contains playable audio
content.
1 Switch the source selector to USB/SD .
2 Insert the SD card into the SD slot on the
back of the device.
3 Press to release the SD/USB source
selector to choose SD source.
» "SD" shows on the display.
» The unit starts to play,If not, press .
CD
USB/SD
FM
TAPE/OFF
AUDIO IN SD
SD USB
10EN
Play tape
1 Slide the source selector to TAPE.
2 Press on main unit to open the tape
door.
3 Load the tape with the open side upward
and the full spool to the right.
4 Press on main unit to start play.
• To pause/resume play, press on main
unit .
• To rewind or fast-forward, press /
on main unit .
• To stop play, press .
CD
USB/SD
FM
TAPE/OFF
AUDIO IN
Tune to FM radio stations
Note
•For optimal reception, fully extend and adjust the
position of the FM antenna.
1 Switch the source selector to FM.
2 Rotate TUNING to select a station.
3 Repeat step 2 to tune to more stations.
CD
USB/SD
FM
TAPE/OFF
AUDIO IN
11 EN
5 Play options
Control play
In CD mode, you can control play through the
following operations.
/ Press:skip to the previous/next
track
Hold:search within play, then
release to resume play.
Start or pause play.
Stop play.
PROG Program tracks.
+VOLUME- Adjust volume.
- ALBUM + Skip the the previous or next
album.
MODE Select a play mode.
[ ]: Play the current track
repeatedly.
[ ]: Play all tracks
repeatedly.
[ ]: Repeat all tracks
randomly.
To return to normal play, press
MODE repeatedly until the
repeat icons disappear.
Tip
•Only [ ] and [ ] can be selected when
you play the programmed tracks.
Program tracks
In CD/USB/SD mode, you can program a
maximum of 20 tracks.
1 Press to stop playback.
2 Press PROG to activate the program
mode.
» [PROG] (program)begintoblink.
3 Press / to select a track number,
then press PROGtoconrm.
4 Repeat steps 3 to program more tracks.
5 Press to play the programmed tracks.
» During play, [PROG] (program)is
displayed.
• To erase the program, press twice.
• When playback is stopped, press /
to review the program.
Adjust sound
During play, you can adjust volume and select
the sound effects.
Key Function
+VOLUME- Increase or decrease volume.
12EN
6 Product
information
Note
•Product information is subject to change without prior
notice.
Specications
Amplier
Max Output Power Total 2 W RMS
Frequency Response 125 -16000 Hz,
-3dB
Signal to Noise Ratio >55 dBA
Total Harmonic Distortion <1 %
Audio-in Input 650 mV RMS
Disc
Laser Type Semiconductor
Disc Diameter 12cm/8cm
Support Disc CD-DA, CD-R,
CD-RW
Audio DAC 24Bits / 44.1kHz
Total Harmonic
Distortion
<1%
Frequency Response 125 -16000 Hz,
-3dB
S/N Ratio >55 dBA
Tuner
Tuning Range 87.5 -
108MHz
Tuning grid 50 kHz
Total Harmonic Distortion <3%
Signal to Noise Ratio >50 dBA
Tape deck
Frequency response
-Normaltape(typeI)
125 - 8000
Hz(8dB)
Signal-to-noise ratio
-Normaltape(typeI)
35 dBA
Wowandutter ≤0.4%
DIN
General
Power supply
- AC Power
- Battery
220-240V~,
50/60 Hz;
9 V, 6 x 1.5 V
type: R14/UM2/C
CELL
Operation Power
Consumption
15 W
Standby Power
Consumption
<0.5 W
Dimensions
-MainUnit(WxHxD)
299 x 240 x 132
mm
Weight(MainUnit) 1.8 kg
13 EN
Maintenance
Clean the cabinet
• Use a soft cloth slightly moistened with
a mild detergent solution. Do not use a
solution containing alcohol, spirits, ammonia
or abrasives.
Clean discs
• When a disc becomes dirty, clean it with
a cleaning cloth. Wipe the disc from the
centre out.
• Do not use solvents such as benzene,
thinner, commercially available cleaners,
or antistatic spray intended for analogue
records.
Clean the disc lens
• After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
play quality, clean the disc lens with Philips
CD lens cleaner or any commercially
available cleaner. Follow the instructions
supplied with cleaner.
Clean the heads and the tape paths
• To ensure good recording and play quality,
clean the heads A,thecapstan(s)B, and
pressureroller(s)C after every 50 hours
of tape operation.
• Use a cotton swab slightly moistened with
cleaninguidoralcohol.
• You can also clean the heads by playing a
cleaning tape once.
Demagnetise the heads
• Use a demagnetising tape available at your
dealer.
14EN
7 Troubleshooting
Warning
•Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).WhenyoucontactPhilips,
make sure that the device is nearby and the
model number and serial number are available.
No power
• Ensure that the Mains cord is connected
securely.
• Ensure that there is power at the AC
Mains.
• Ensure that the batteries are inserted
correctly.
No sound or poor sound
•Adjust the volume.
No response from the unit
•Disconnect and reconnect the AC power
plug, then turn on the system again.
•As a power-saving feature, the unit
switches off automatically 15 minutes after
track play reaches the end and no control
is operated.
Poor cassette sound quality
• Ensure that heads in the cassette holder
are clean.
• EnsurethataNORMAL(IECI)cassette
tape is used for record.
Cassette does not work for record
• Ensure that cassette tabs are not broken.
No disc detected
•Insert a disc.
•Check if the disc is inserted upside down.
•Wait until the moisture condensation at
the lens has cleared.
•Replace or clean the disc.
•UseanalizedCDorcorrectformatdisc.
Poor radio reception
•Increase the distance between the unit and
your TV or VCR.
•Fully extend the FM antenna.
Specifications are subject to change without notice
2013 © WOOX Innovations Limited.
All rights reserved.
Philips and the Philips’ Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used by WOOX
Innovations Limited under license from Koninklijke Philips N.V.
AZ329_98_UM_V2.0