Philips BDL4251V/00 User Manual

Displayed below is the user manual for BDL4251V/00 by Philips which is a product in the Signage Displays category. This manual has pages.

Related Manuals

Philips SPC900NC/00 Manual

Public Signage Solutions

User

Manual

TYPE NR. BDL4251V

User Manual BDL4251V

TABLE OF CONTENTS

SAFETY INSTRUCTIONS.................................................................................................................................................................................2

Contents ................................................................................................................................................................................................................ 8

Connection & Button Overviews....................................................................................................................................................................9

Terminal Panel ...........................................................................................................................................................................................10

Remote Control........................................................................................................................................................................................11

Operating Range for the Remote Control.........................................................................................................................................12

Handling the remote control.................................................................................................................................................................12

How to Mount or Attach Feet to the LCD Monitor................................................................................................................................13

Setup Procedure.................................................................................................................................................................................................16

Install the LCD Monitor in Portrait Mode ..................................................................................................................................................18

Connectivity........................................................................................................................................................................................................19

Connectivity Diagram..............................................................................................................................................................................19

Connecting to a Personal Computer...................................................................................................................................................20

Connecting to a Digital Interface Equipment.....................................................................................................................................21

Connecting to a DVD Player .................................................................................................................................................................22

Connecting to a Stereo Amplifier.........................................................................................................................................................23

Connecting to a display mounted PC..................................................................................................................................................23

Basic Operation..................................................................................................................................................................................................24

Power ON and OFF Modes...................................................................................................................................................................24

Power Indicator.........................................................................................................................................................................................25

Using Power Management......................................................................................................................................................................25

Display Signal of Video Source Setting to [VIDEO]..........................................................................................................................25

Picture Size.................................................................................................................................................................................................25

Smart Picture Mode.................................................................................................................................................................................26

Audio Source Switching ..........................................................................................................................................................................26

Control Lock Mode .................................................................................................................................................................................26

OSD Information......................................................................................................................................................................................26

OSD (On-Screen-Display) Controls..............................................................................................................................................................27

PICTURE.....................................................................................................................................................................................................28

SCREEN......................................................................................................................................................................................................30

AUDIO........................................................................................................................................................................................................32

PIP (PICTURE IN PICTURE).................................................................................................................................................................33

CONFIGURATION 1..............................................................................................................................................................................34

CONFIGURATION 2..............................................................................................................................................................................36

ADVANCED OPTION............................................................................................................................................................................38

NOTE ..........................................................................................................................................................................................................41

Features ................................................................................................................................................................................................................45

Troubleshooting..................................................................................................................................................................................................46

Specifications.......................................................................................................................................................................................................48

Pin Assignment....................................................................................................................................................................................................49

User Manual BDL4251V

SAFETY INSTRUCTIONS

WARNINGS AND PRECAUTIONS

KNOW THESE SAFETY SYMBOLS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any

inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included

with this product.

Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article

820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as

practical.

Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to

operate it.

Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.

Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la bome correspondante de la prise et pousser

jusqu’au fond.

Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of U.S. copyright laws.

Certain Canadian programs may also be copyrighted and any unauthorized recording in whole or in part may be in violation of these rights.

TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

The Socket-outlet shall be installed near th e apparatus and shall be easily accessible.

Read and follow these instructions when connecting and using your computer monitor:

 Unplug the monitor if you are not going to use it for an extensive period of time.

 Unplug the monitor if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth

when the power is off. However, never use alcohol, solvents or ammonia-based liquids.

 Consult a service technician if the monitor does not operate normally when you have followed the instructions in this

manual.

 The casing cover should be opened only by qualified service personnel.

 Keep the monitor out of direct sunlight and away from stoves or any other heat source.

 Remove any object that could fall into the vents or prevent proper cooling of the monitor’s electronics.

 Do not block the ventilation holes on the cabinet.

 Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture.

 If turning off the monitor by detaching power cable or DC power cord, wait for 6 seconds before attach the power

cable or DC power cord for normal operation.

 To avoid the risk of shock or permanent damage to the set do not expose the monitor to rain or excessive moisture.

 When positioning the monitor, make sure the power plug and outlet are easily accessible.

 IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast

remains on the screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of

the screen. This is a well-known phenomenon that is caused by the shortcomings inherent in the LCD technology. In

most cases the afterimage will disappear gradually over a period of time after the power has been switched off. Be

aware that the after-image symptom cannot be repaired and is not covered under warranty.

User Manual BDL4251V

REGULATORY INFORMATION

CE DECLARATION OF CONFORMITY

MMD declare under our responsibility that the product is in conformity with the following standards

• EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment)

• EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment)

• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)

• EN6100-3-2: 2006 (Limits for Harmonic Current Emission)

• EN6100-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable

• 2006/95/EC (Low Voltage Directive)

• 2004/108/EC (EMC Directive)

• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 level.

FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

In a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING

EQUIPMENT REGULATIONS.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.



User Manual BDL4251V

POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works

together (computer, monitor, printer, and so on) should have the same power supply source.

The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with

a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be

located near the equipment and easily accessible.

A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-

42107 and PN-89/E-06251.

ELECTRIC, MAGNETIC AND ELECTRONMAGNETIC FIELDS (“EMF”)

1. MMD manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit

and receive electromagnetic signals.

2. One of MMDs’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable

legal requirements and to stay well within the EMF standards applicable at the time of producing the products.

3. MMD is committed to develop, produce and market products that cause no adverse health effects.

4. MMD confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available

today.

5. MMD plays an active role in the development of international EMF and safety standards, enabling MMD to anticipate further developments

in standardization for early integration in its products.



User Manual BDL4251V

INFORMATION FOR UK ONLY

WARNING - THIS APPLIANCE MUST BE EARTHED.

Important:

This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this

type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an

appropriate 3-pin plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug

without a fuse is used, the fuse at the distribution board should not be greater

than 5A.

Note: The severed plug must be destroyed to avoid a possible shock hazard should it

be inserted into a 13A socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured in accordance with the following code:

BLUE - “NEUTRAL” (“N”)

BROWN - “LIVE” (“L”)

GREEN & YELLOW - “EARTH” (“E”)

1. The GREEN AND YELLOW wire must be connected to the terminal in

the plug which is marked with the letter “E” or by the Earth symbol or

coloured GREEN or GREEN AND YELLOW.

2. The BLUE wire must be connected to the terminal which is marked with the letter

“N” or coloured BLACK.

3. The BROWN wire must be connected to the terminal which marked with the letter

“L” or coloured RED.

Before replacing the plug cover, make certain that the cord grip is clamped over the

sheath of the lead - not simply over the three wires.



User Manual BDL4251V

中国电子信息产品污染控制标识要求(中国RoHS法规标示要求)产品中有毒有害物质或

元素的名称及含量

有毒有害物质或元素

部件名称

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr 6+)

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

外壳 ○ ○ ○ ○ ○ ○

液晶面板 × × ○ ○ ○ ○

电路板组件 × ○ ○ ○ ○ ○

附件

(遥控器、电源线、连接线) × ○ ○ ○ ○ ○

遥控器电池 × ○ ○ ○ ○ ○

○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006标准规定的限量要求

以下。

×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限

量要求。

环保使用期限

此标识指期限(十年)，电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外

泄或突变，电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身、财产造成

严重损害的期限。

User Manual BDL4251V

NORTH EUROPE (NORDIC COUNTRIES) INFORMATION

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation

ADVARSEL:

SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.

Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.

Plassering/Ventilasjon

ADVARSEL:

NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.

END-OF-LIFE DISPOSAL

Your new TV/Monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the

amount of reusable materials and to minimize the amount to be disposed of.

Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on

recycling contact www.eia.org (Consumer Education Initiative)

WASTE ELECTRICAL AND ELECTRONIE EQUIPMENT-WEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG

governing used electrical and electronic appliances, this product may not be disposed of with normal

household waste. You are responsible for disposal of this equipment through a designated waste electrical

and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local

government office, the waste disposal organization that serves your household or the store at

which you purchased the product.

Attention users in United States:

Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal Laws. For the disposal

or recycling information, contact: www.mygreenelectronics.com or www.eiae.org.

User Manual BDL4251V

Contents

The BDL4251V monitor pack* should include:

• LCD monitor

• Power cord (1.8 m)

• VGA Signal Cable (1.8 m)

• CD User Manual & QSG

• Remote Control and AAA Batteries

• Cable belt x 3 (For tightening cables)

• Main switch cover

• Screw for Main Switch cover x 2

• BNC TO RCA adapter x 5

• Logo guider

• Clamper

• Screw for Clamper x 2

xxxxxxxxxx

xxxxxxxxxxxx

xxxxxxxxx

Video Signal Cable

(D-SUB to D-SUB Cable)

Logo guider

Please make sure that for

all

other

regions, apply a

power cord

conforms to

the

voltage of the power socket and has been approved by and complies with

the safety regulations of the particular country.

* You might like to save the package box and packing material for shipping the

monitor.

* The foll

owing components are prepared as options.

• External

Speakers

• Table

stand

Clamper

Screw for Clamper

(M4 x 8) x 2

CD Use

Manual & QSG

BNC TO RCA adapte

x 5

ew for Main switch cove

(M3 x 6) x 2

Main switch cove

Cable bel

x 3

(For tightening the power

cord and VGA / HDMI

cable)

Remote Con

ol and AAA

Batteries

Power co

For North

America

For China For EU

* The supplied power co

d varies depending on destination.

User Manual BDL4251V

Connection & Button Overviews

Control Panel

POWER button ( ) : To switch the power on/off.

MUTE button : To switch the audio mute ON/OFF.

INPUT button : To set the function while OSD menu is on or to activate input selection menu while OSD menu is off.

PLUS (+) button : To increase the adjustment while OSD menu is on, or to increase the audio output level while the OSD menu is off.

MINUS (-) button : To decrease the adjustment while OSD menu is on, or to decrease the audio output level while the OSD menu is off.

UP () button : To move the highlight bar up to adjust the selected item while OSD menu is on, or to activate the OSD menu when the OSD

menu is off.

DOWN () button :To move the highlight bar down to adjust the selected item while OSD menu is on, or to activate the OSD menu when

the OSD menu is off.

EXIT button : To return to previous menu while OSD menu is on or to activate the OSD menu when the OSD menu is off.

Main Power Switch : To turn the main power on/off.

Remote control sensor, Power indicator and ambient light sensor : To receive the IR signal from the remote control. The

indicator would show green when the LCD monitor is active and would turn red when the LCD is POWER OFF. While in the case of the system is in

power save mode, it would show both green and red. When SCHEDULE is enabled, it would blink green and glow red. If the indicator blinks red , it

tells that a failure is detected. The image brightness will be auto adjusted when “LIGHT SENSOR” set to “ON” on OSD menu.

NOTE: Keyboard Control Lock Mode This function completely disables the access to all Keyboard Control functions. To enable the

keyboard control lock, press both of “” and “” buttons and hold down continuously for more than 3 seconds. To recover back to the user mode,

press both of “” and “” and hold continuously for three 3 seconds.

User Manual BDL4251V

Terminal Panel

EXTERNAL CONTROL (mini D-Sub 9 pin)

This is for serial connection when multiple BDL4251V monitors are connected. To achieve remote management through RS232C commands (refer to

the RS232C remote control user manual), connect the RS232C OUT connector from a computer or from a different BDL4251V monitor to the

RS232C IN connector from your BDL4251V monitor. The same RS232C commands can be looped through by connecting the RS232C OUT of this

monitor to the next RS232C IN.

VIDEO IN/OUT

VIDEO IN connector (BNC and RCA): To input a composite video signal. Note that BNC and RCA are not available at the same time.

VIDEO OUT connector (BNC): To output the composite video signal from VIDEO IN connector.

S-VIDEO IN connector (MINI DIN 4 pin): To input the S-video (Y/C separate signal).

COMPONENT IN [Y, Pb, Pr] (BNC)

To connect an equipment such as a DVD player, HDTV device, or Laser disc player.

AC OUT connector

Bypass AC power output from AC IN connector. (Rating : 100~240Vac, 50-60Hz, 3A Max.)

AC IN connector

To connect with the supplied power cord.

EXTERNAL SPEAKER TERMINAL

To output the audio signal to external speakers from AUDIO IN 1, 2, 3 jack or HDMI.

AUDIO OUT

To output the audio signal from the AUDIO IN 1,2 and 3 jack or HDMI.

AUDIO IN 1, 2, 3

To input audio signal from external equipment such as a computer, VCR or DVD player.

HDMI IN

To input digital video/audio signals from a digital equipment or computer.

DVI-D IN

To input digital video signals from a digital equipment or computer.

VGA IN (mini D-Sub 15 pin)

To input analog RGB signals from a computer or other RGB equipment.

VGA OUT (mini D-Sub 15 pin)

To output the signal from VGA IN.

User Manual BDL4251V

Remote Control

POWER button

To turn the power on/off.

If LED Power Indicator on the monitor is not lightening, then the

remote control will not work.

SMART PICTURE button

To select smart picture mode from [HIGHBRIGHT], [STANDARD],

[sRGB], [CINEMA].

HIGHBRIGHT: for moving image such as Video

STANDARD: for images (Factory setting)

sRGB: for text based images

CINEMA: for movies.

PIP (Picture In Picture) button

ON/OFF button: To t u r n PIP mode ON/OFF.

INPUT button: To select the input signal for the sub-picture.

CHANGE button: To exchange between the main picture and sub-

picture.

Note:

The “PIP” and “POP” modes do not work if the screen size is

“CUSTOM” , “DYNAMIC” or “REAL”.

CONTRAST button

To s ta r t CONTRACT OSD selection, and then push "+" or "-" button

to adjust the value.

DISPLAY button

To turn on/off the setting information displayed on the right-up corner

of the screen.

MINUS button

To decrease the adjustment with OSD menu.

To move the sub-picture left when in “PIP” mode.

SET button

To activate the setting with OSD menu.

AUTO ADJUST button

To execute the AUTO ADJUST function.

MUTE button

To turn the mute function on/off.

VIDEO SOURCE button

To activate input selection menu, and push “” or “” to select input

source from [HDMI], [DVI-D], [VGA],[COMPONENT], [S-VIDEO] and

[VIDEO], and then push “SET” to switch to selected input source.

AUDIO SOURCE button

To activate audio selection menu, and push “” or “” to select audio

source from [AUDIO1], [AUDIO2], [AUDIO3] and [HDMI], and then

push “SET” to switch to selected audio source.

SIZE button

To select the picture size from [FULL], [NORMAL], [CUSTOM] ,

[DYNAM IC] and [REAL].

BRIGHTNESS button

To start the BRIGHTNESS OSD selection, and then push "+" or "-"

button to adjust the value.

UP button

To move the highlight bar up to adjust the selected item when OSD menu

is on.

To move the sub-picture up when in “PIP” mode.

MENU button

To turn the OSD menu on/off.

PLUS button

To increase the adjustment with OSD menu.

To move the sub-picture right when in “PIP” mode.

EXIT button

To turn to the previous OSD menu.

DOWN button

To move the highlight bar down to adjust the selected item when OSD

menu is on.

To move the sub-picture down when in “PIP” mode.

VOLUME UP button

To increase the audio output level.

VOLUME DOWN button

To decrease the audio output level.

User Manual BDL4251V

Operating Range for the Remote

Control

Point the top of the remote control towards the LCD monitor's remote

sensor during button operation.

Use the remote control within a distance of about 7 m/ 23 ft from the

front of the LCD monitor's remote control sensor and within a

horizontal and vertical angle 30° with a distance of about 3 m/ 10 ft.

Handling the remote control

* Do not subject to strong shock.

* Do not allow water or other liquid to splash the remote control.

If the remote control gets wet, wipe it dry immediately.

* Avoid exposure to heat and steam.

* Other than to install the batteries, do not open the remote

control.

NOTE:

The remote control system may not function when direct sunlight or strong

illumination strikes the remote control sensor of the LCD monitor, or when

there is an obstacle in the radiation path.

User Manual BDL4251V

How to Mount or Attach Feet to the LCD Monitor

You can install the LCD monitor in one of the following two ways:

Method 1: Attach and remove the optional stands

How to install stands

1. Please turn the monitor off.

2. After inserting stand in guide block, fasten the thumbscrews on both sides of the monitor.

NOTE:

Install the table stand with the longer end of the feet directing to the front.

In the upright position

How to remove the stands

1. Spread the protective sheet on the flat surface.

2. Make the monitor lying on the protective sheet.

3. Remove screws using a screwdriver and place them in a safe place for reuse.

User Manual BDL4251V

To avoid monitor from falling

Take measures to prevent the monitor from falling over in case of an earthquake or other disaster might occur to lessen the probability of injury and

damage.

As shown in the figure below, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the

monitor(BDL4251V: approx. 47.5 kg). Screw hooks (commercially available), of ring type rather than C-shaped screw hooks (with opening), are

recommended.

Caution:

 Though the recommended prevention from falling is intended to lessen the probability of injury and damage, it doesn’t assure its effectiveness

against any kind of earthquake or disaster.

 Before moving the monitor, remove the rope that is securing the monitor.

Method II: Mount the monitor on the wall

Before mounting the monitor to the wall, make sure that the system has been power-off and you have obtain a standard wall-mounting kit

(commercially available). Using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America is recommended.

1. Lay a protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the surface as not to scratch the screen

face.

2. This device cannot be installed without the correct and complete mounting accessories (not provided in the box). Make sure you have all related

parts available for wall mounting.

3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the

equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation.

4. For the wall-mounting kit, use M6 mounting screws for 400x 400 mm pattern (having a length 10 mm longer than the thickness of the mounting

bracket) and tighten them securely. (Recommended torque: 470 - 635N•cm).

Caution:

For preventing the monitor from falling.

 Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed procedures of

installation, refer to the instructions of the metal brackets.

 To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to consult the

bracket manufacturer for installation location.

 To lessen the risk of falling of the monitor, thread commercially available rope (having a load capacity at least 1960N (200kgf)) through the handles

at the right and left of the monitor and secure the rope to the wall mount brackets or ceiling mount brackets.(Refer to the first paragraph of this

page.)

Screw here is not supplied.

User Manual BDL4251V

Ventilation Requirements for enclosure locating

To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.

User Manual BDL4251V

Setup Procedure

1. Install the system on the right location

CAUTION:

THE LCD MONITOR MUST BE MOVED OR INSTALLED BY TWO

OR MORE PERSONS.

Failure to follow this caution may result in injury and damage when

the LCD monitor falls.

CAUTION:

DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY

YOURSELF.

The LCD display must be installed by a qualified technician. Contact

your dealer for more information.

CAUTION:

DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN,

FACE UP OR FACE DOWN.IT’S POSSIBILITY TO CLOCKWISE 90

DEGREES MOUNT. BUT DO NOT COUNTERCLOCKWISE 90

DEGREES MOUNT.

CAUTION:

DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE

EXPOSED TO DIRECT SUNLIGHT.

Failure to follow this caution will result in display defects.

IMPORTANT:

Lay the protective sheet, which was wrapped around the LCD

monitor when it was packaged, beneath the LCD monitor so as not to

scratch the panel.

2. Install the remote control batteries

The remote control is powered by 1.5V AAA batteries. To install or

replace batteries:

1. Press and slide to open the cover.

2. Align the batteries according to the (+) and (–) indications inside

the case.

3. Replace the cover.

CAUTION:

Incorrect use of batteries can result in leaks or bursting. Be careful

especially about the following points.

• Place “AAA” batteries matching the + and - signs on each battery

to the + and - signs of the battery compartment.

• Do not mix battery types.

• Do not combine new batteries with used ones. It causes shorter

battery life or leakage of batteries.

• Remove dead batteries immediately to prevent battery liquid from

leaking into the battery compartment. Don't touch exposed

battery acid, it cause damage to your skin.

NOTE:

If you do not intend to use the Remote Control for a long period,

remove the batteries.

3. Connect to external equipment

• To protect the connected equipment, turn off the main power before

making connections.

• Please refer to section “Connectivity” P.18~P.22 for operations.

4. Connect power cord

• The power outlet socket should be installed as near to the equipment

as possible, and should be easily accessible.

• Fully insert the prongs into the power outlet socket. A loose

connection may cause malfunctioning of the device.

NOTE:

Please refer to “Safety Operation” section of this manual for proper

selection of AC power cord.

5. Turn on the power of the attached

external equipment

When connected with a computer, turn on the power of the computer

first.

6. Operate the attached external equipment

Display the signal from the external equipment by selecting the correct

video and audio sources first.

7. Adjust the sound

Make adjustments to lower or to rise the volume as required.

8. Adjust the screen

Make adjustments to the display position or settings if required.

User Manual BDL4251V

9. Adjust the image

Make adjustments to brightness or contrast if required.

10. Recommended Adjustment

To reduce the risk of “image persistence”, please adjust the

following items based on the application being used.

“POWER SAVE”, “PANEL SAVING”, “DATE AND TIME”.

11. To prevent the main power switch from

being changed

To prevent the possibility of main power switch being carelessly

pushed, please attach the main switch cover (accessory) onto it.

NOTE:

With the main power switch cover in place, the main power switch

can not be turned off. Remove main power switch cover in order to

turn off the display.

User Manual BDL4251V

Install the LCD Monitor in Portrait Mode

BDL4251V can be installed in portrait position, under the following conditions:

Caution:

Portrait mode is effective only when wall-mounted or ceiling-mounted. The feet can not be used for the monitor in portrait position.

Placing the monitor in portrait position, will shorten the average life of the LCD backlight.

Operational Environment (Temperature) shall be limited, as shown below:

Temperature 5 - 35 °C / 41 - 95 °F Operational

Environment Humidity 20 - 80 % (without condensation)

Please orientate the monitor in the direction shown as the right figure:

Do not place monitor in landscape in any other manner.

How to set-up

1. Remove the feet if they are attached.

2. The “ ” logo should be on the LEFT side when facing the monitor.

How to Remove the Logo for landscape mode?

1. Remove the logo sticker by forcing a piece of paper under the logo.

2. Using a knife, carefully remove the logo sticker with the paper placing

beneath.

3. Tear off the logo sticker.

How to Use the Logo Guider for Portrait Mode?

1. Before applying, make sure the guider is well shaped. The "PHILIPS"

sticker attached on the end of it could be folded back as figure a.

2. Turn back the logo end of the guider and remove the sticky tape of the

logo.

3. Slide the logo guider along the short side of the front bezel as figure c &

then re-turn the logo end of the guider back to the right side.

4. With your left hand fixing the guider, press the logo by your right hand to

make it stuck firmly on the front bezel.

5. Remove the guider and leave the logo on the front bezel.

Clockwise

Counte

clockwise

User Manual BDL4251V

Connectivity

Before making connections:

* First turn off the power of all the attached equipments before make connections.

* Refer to the user manual included in each separate piece of equipment.

Connectivity Diagram

User Manual BDL4251V

Connecting to a Personal Computer

As you finish the connection between the computer and the LCD monitor, you could play the contents in the computer and display them on the

LCD monitor.

Connecting the LCD Monitor to a Personal Computer

• To achieve this, apply the supplied VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin) to make connection between a PC and the LCD

monitor (VGA IN connector).

• When connecting more than one LCD monitors to a PC, apply another VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin; it’s

commercially available) to make connection between the LCD monitor(VGA OUT connector) and the other (VGA IN connector).

• The AUDIO IN 1, 2, 3 or HDMI can be connected for audio input. After choosing one of the AUDIO IN connectors, you might need to select

AUDIO 1, 2, 3 or HDMI using the AUDIO SOURCE button on the remote control.

• When connecting more than one LCD monitors to a PC, apply RCA cable to make connection between the LCD monitor(AUDIO OUT

connector) and the other (AUDIO IN 1, 2, 3). HDMI source is not suitable for this case.

User Manual BDL4251V

Connecting to a Digital Interface Equipment

Connections can be made between the LCD monitor and other digital equipment that is equipped with a digital interface compliant with the DVI

(Digital Visual Interface) standard.

Connect the LCD Monitor to a Computer with a Digital Output

• The HDMI , DVI-D IN connector accepts a HDMI cable.

• HDMI and DVI-D can receive HDMI video signals from either a HDMI output of for instance a DVD player or from a DVI-D output of a PC.

• To ensure the display quality, use a cable with a quality prescribed by DVI standards.

• The AUDIO IN 1, 2, 3 or HDMI connector can be chosen to receive an audio source. Select AUDIO 1, 2, 3 or HDMI from the AUDIO

SOURCE button on the remote control. HDMI(for audio) is only selectable only when HDMI or DVI-D (for video) is selected.

• Note that the signal of a HDMI / DVI-D connector cannot be output to the VGA OUT connector.

User Manual BDL4251V

Connecting to a DVD Player

As you finish the connection between the DVD player and the LCD monitor, you could display the contents from the played DVD on the LCD

monitor. You might like to refer to your DVD player’s manual for further information.

Connect the LCD Monitor to a DVD Player

• To achieve this, apply a 3x components cable (Y, Pb, Pr) with BNC connectors at one end and RCA connectors at the other end between DVD

player and display. In case you can only obtain RCA connectors on both ends you can use the in box available BNC-to-RCA converters.

DVD player(Y, Pb, Pr Out) and LCD monitor (COMPONENT). You might need BNC-to-RCA adapters(including in the accessories) to convert

the BNC connectors to RCA connectors if you are using the separated signaling(Y, Pb, Pr) RCA cable.

• If your DVD player supports HDMI signaling, apply a HDMI to HDMI cable for the connection.

• The AUDIO IN 2 , 3 (both of RCA connector type) can be used for audio input. Select [AUDIO 1] (for 3.5φ phone jack), [AUDIO 2], [AUDIO

3] Or [HDMI] from the AUDIO SOURCE button on the remote control. HDMI (for audio) is selectable only when HDMI or DVI-D (for video)

is selected.

User Manual BDL4251V

Connecting to a Stereo Amplifier

You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier's manual for further information.

Connect the LCD Monitor to a Stereo Amplifier

• Turn on the LCD monitor and the amplifier only after all connections have been finished.

• Apply 2 RCA cables (audio left and right) to make connection between the amplifier (audio in) and the LCD monitor (audio out).

• Do not reverse the audio left and right jacks.

• For the preferred audio signal, select [AUIDO1], [AUDIO2], [AUDIO3] or [HDMI] from the AUDIO SOURCE button on the remote control.

HDMI(for audio) is selectable only when HDMI or DVI-D (for video) is selected.

• The AUDIO OUT RCA connectors output sound from the selected AUDIO SOURCE.

Connecting to a display mounted PC

This monitor has an area in the backcover to mount a small form fact PC or set-top box.

You can connect your mounted PC to your LCD monitor. Use M4 mounting screws for 100x234 mm to fix your mount PC.

User Manual BDL4251V

Basic Operation

Power ON and OFF Modes

The LCD monitor power indicator will turn green while powered on and will turn red while powered off. The monitor can be powered on or off

using the following three options:

1. Pressing the Main Power Switch.

NOTE:

When the Main Power Switch is used to power off the LCD monitor,

the remote control, the power button and the indicator will not work.

Make sure to turn the Main Power Switch on before using the other

two options.

2. Pressing the power button.

NOTE:

Before pressing the power button, be sure to turn on the Main Power

button on the LCD monitor.

3. Using the remote control.

NOTE:

Before operating the remote control, be sure to turn on the Main

Power Switch on the LCD monitor.

User Manual BDL4251V

Power Indicator

Status

Power ON Green

Power Standby Red

Power OFF LED Off

Diagnosis

(Detecting failure)

Red Blinking

* See troubleshooting

Using Power Management

Please turn off the LCD monitor when it will not be used for long time. This could potentially increase the life and decrease the power consumption

of the LCD monitor.

Standby mode: Push the power button on the remote control or on the monitor to enter the standby mode.

Power Off: Push the Main Power Switch to enter the power off mode.

Display Signal of Video Source Setting to [VIDEO]

Use the input button on the front panel or the VIDEO SOURCE button on the remote control to set video source to [VIDEO].

Use the COLOR SYSTEM OSD menu to select [AUTO], [NTSC], [PAL], [SECAM], [PAL60], [4.43NTSC], according to your video format.

Picture Size

HDMI, DVI-D, VGA FULL NORMAL CUSTOM

REAL

COMPONENT, VIDEO FULL NORMAL DYNAMIC

REAL CUSTOM

Signal Type NORMAL SIZE Recommended Size

NORMAL

4:3

DYNAMIC

Squeeze

FULL

NORMAL: Display with the input signal aspect ratio from PC signal, or display in 4:3 aspect ratio at COMPONENT or VIDEO signal.

FULL: Display in the entire screen.

DYNAMIC: Expand 4:3 pictures to the entire screen with non-linearity. (Some round image might be cut by expansion.)

CUSTOM (ZOOM): Images can be expanded beyond the active display area. The image which is outside of the active display area would not be

shown.

REAL: Image will be displayed for one by one pixel.

ZOOM

User Manual BDL4251V

Smart Picture Mode

HDMI, VGA HIGHBRIGTH STANDARD sRGB

COMPONENT, VIDEO HIGHBRIGTH STANDARD CINEMA

Audio Source Switching

You can select the audio source using the AUDIO SOURCE button on the remote control.

HDMI HDMI AUDIO1 AUDIO2 AUDIO3

Control Lock Mode

This function disables the operation o buttons so that the adjustments you make are not active when they are pressed.

To disable the buttons, press and hold down the  and  buttons together for at least 3 seconds.

To enable the buttons, press and hold down the  and  buttons together for at least 3 seconds again.

OSD Information

HDMI, VGA

VGA

1024 x 768

48kHz 60Hz

AUDIO : 1

SIZE : FULL

Video Source

Input signal Information

Audio Source

Picture Size

COMPONENT

AUDIO : 3

SIZE : FULL

Video Source

Audio Source

Picture Size

S-VIDEO, VIDEO

S-VIDEO

NTSC

AUDIO :3

SIZE : NORMAL

Video Source

Color System of Input Signal

Audio Source

Picture Size

PIP or POP

Main:VGA

Sub:S-VIDEO

VGA

1024 x 768

48kHz 60Hz

AUDIO : 1

S-VIDEO

NTSC

SIZE : FULL

Main picture Information

Sub picture Information

Main picture Information

User Manual BDL4251V

OSD (On-Screen-Display) Controls

Remote Control

Control Panel

Press MENU button to

open Main menu. Press

UP or DOWN button to

select sub-menu.

Press EXIT button to open

Main menu. Press UP or

DOWN button to select.

Press SET button

to enable setting.

Press INPUT button to

enable the setting.

Press UP or DOWN, and PLUS or

MINUS button to select function,

or adjust the setting. Press SET

button to enable the setting.

Press UP or DOWN, and PLUS or

MINUS button to select function,

or adjust the setting. Press INPUT

button to enable the setting.

Press MENU or

EXIT button to exit.

Press EXIT button to exit.

UP or DOWN button INPUT button

“+” “-” button EXIT button

OSD screen

User Manual BDL4251V

Main-Menu

PICTURE

BRIGHTNESS

Adjusts the overall image and background screen brightness.

Press + button to increase brightness.

Press - button to decrease brightness.

CONTRAST

Adjusts the image brightness for the input signal.

Press + button to increase contrast.

Press - button to decrease contrast.

SHARPNESS

This function is digitally capable to keep crisp images at any timing.

It is adjustable to get a distinct image or a soft one as you prefer and set independently for each

picture mode.

Press + button to increase sharpness.

Press - button to decrease sharpness.

BLACK LEVEL

Adjusts the image brightness for the background.

Press + button to increase black level.

Press - button to decrease black level.

NOTE: sRGB picture mode is standard and cannot be changed.

NOISE REDUCTION

Adjusts the noise reduction level.

Press + button to increase reduction level.

Press - button to decrease reduction level.

TINT * : INPUT HDMI , (HDMI INPUT MODE-HD), COMPONENT, S-VIDEO, VIDEO only

Adjusts the tint of the screen.

Press + button the flesh tone color becomes greenish.

Press - button the flesh tone color becomes purplish.

User Manual BDL4251V

COLOR * : INPUT HDMI , DVI-D(INPUT MODE-HD), COMPONENT, S-VIDEO, VIDEO only

Adjusts the color of the screen.

Press + button to increase color depth.

Press - button to decrease color depth.

COLOR TEMPERATURE

Is used to adjust the color temperature.

The image becomes reddish as the color temperature decreases, and becomes bluish as the color

temperature increases.

COLOR CONTROL

The color levels of red, green, and blue are adjusted by the color bars.

R: Red, G: Green, B: Blue

LIGHT SENSOR

Select “ON” to enable the ambient light sensor. The image brightness will be auto adjusted when

ambient light changed.

SMART CONTRAST

Select “ON” to enable the smart contrast. Can enhancement the image of high contrast ratio.

PICTURE RESET

Selecting Picture reset allows you to reset all OSD settings about PICTURE setting.

Select “Yes” and press “SET” button to restore to factory preset data.

Press “EXIT” button to cancel and then return to the previous menu.

User Manual BDL4251V

Main-Menu

SCREEN

H POSITION

Controls Horizontal Image position within the display area of the LCD.

Press + button to move screen to right.

Press - button to move screen to left.

V POSITION

Controls Vertical Image position within the display area of the LCD.

Press + button to move screen to UP.

Press - button to move screen to DOWN.

CLOCK * : INPUT VGA only

Press + button to expand the width of the image on the screen the right.

Press - button to narrow the width of the image on the screen the left.

CLOCK PHASE * : INPUT VGA only

Improves focus, clarity and image stability by increasing or decreasing this setting.

ZOOM MODE

You can select “FULL”, “NORMAL” and “CUSTOM” and “REAL”. (INPUT HDMI,DVI-D,VGA only)

You can also select “FULL”,“NORMAL” “DYNAMIC” and “CUSTOM” and “REAL”. (INPUT

COMPONENT, S-VIDEO, VIDEO only)

Selecting “DYNAMIC” will make the screen display panoramic with the expansion of the middle and outside

of the screen changed. (The upper and the bottom of the image will be cut by expansion.)

Dynamic image is the same as FULL size image when HDTV signal is input.

Selecting “REAL” image will be displayed 1 by 1 pixel.

User Manual BDL4251V

CUSTOM ZOOM

“CUSTOM ZOOM” will be selected when you select “CUSTOM” on the screen “ZOOM” mode.

ZOOM: expands the horizontal and the vertical size simultaneously.

HZOOM: expands the horizontal size only.

VZOOM: expands the vertical size only.

H POSITION: moves to the right with + button. moves to the left with – button.

V POSITION: moves up with + button. moves down with – button.

SCREEN RESET

Selecting Screen reset allows you to reset all OSD settings from PICTURE setting.

Select “Yes” and press “SET” button to restore the factory preset data.

Press “EXIT” button to cancel and then return to the previous menu.

User Manual BDL4251V

Main-Menu

AUDIO

BALANCE

Adjusts the balance of L/R volume.

Press + button to move the stereo sound image to right.

Sound of the left side will be small.

Press - button to move the stereo sound image to left.

TREBLE

This feature helps you to accentuate or reduce the high frequency sound.

Press + button to increase TREBLE sound.

Press - button to decrease TREBLE sound.

BASS

This feature helps you to accentuate or reduce the low frequency sound.

Press + button to increase BASS sound.

Press - button to decrease BASS sound.

SPEAKER

This feature helps you to cut the internal or the external loudspeaker.

Press + or - button to exchanges the internal and the external loudspeaker.

AUDIO RESET

Selecting Audio reset allows you to reset all OSD settings from AUDIO setting.

Select “YES” and press “SET” button to restore the factory preset.

Press “EXIT” button to cancel and then return to the previous menu.

User Manual BDL4251V

Main-Menu

PIP (PICTURE IN PICTURE)

Note: The “PIP” and “POP” modes do not function when the screen size is “CUSTOM” or “REAL”.

PIP SIZE

Selecting the size of picture inserted at the “Picture-in-Picture” (PIP) mode.

“Large”, “Middle” and “Small” are available.

PIP AUDIO

Selecting the sound source in PIP mode.

When selecting “MAIN AUDIO”, you will get the sound for the main picture and when selecting

“PIP AUDIO”, you will get the sound for the picture instead.

PIP RESET

Selecting PIP Reset allows you to reset all OSD settings from PIP setting.

Select “Yes” and press “SET” button to restore the factory preset data.

Press “EXIT” button to cancel and then return to the previous menu.

User Manual BDL4251V

Main-Menu

CONFIGURATION 1

AUTO ADJUST * : INPUT VGA only

Press "SET" button to automatically adjust screen size, horizontal position, vertical position, clock,

clock phase, white level and black level.

Press " EXIT " button to cancel execution AUTO ADJUST and then will return to the previous menu.

POWER SAVE

Selecting RGB "ON", the monitor will go to power management mode when HDMI, DVI-D,VGA, sync is

lost.

Selecting VIDEO "ON", the monitor will go to power management mode after about 10 minutes delay

from when COMPONENT and VIDEO input signal is lost.

LANGUAGE

OSD control menus are available in eight languages.

(English, German, French, Italian, Spanish, Polish, Turkish, Russian, Simple Chinese)

PANEL SAVING

Select "PANEL SAVING" functions to reduce the risk of the "image persistence".

COOLING FAN: The cooling fan will be auto-turned on and off according to temperature of monitor

when selected “AUTO”. The cooling fan will be turned on always when selected “ON”.

BRIGHTNESS: The brightness is decreased when selected "ON".

PIXEL SHIFT: Image is slightly expanded and moves 4 directions (UP, DOWN, RIGHT, LEFT) periodically

(Need setting the time for movement).

Movement area is approximately +/- 10mm from original position;

Please locate the important information such as text within 90% area of screen image.

See note (1) for this functions.

PIP and STILL will be disabled when "MOTION" is active.

COLOR SYSTEM * : INPUT S-VIDEO, AV only

Selecting the Color System depends on your input video format.

AUTO: NTSC, PAL, SECAM, PAL60 or 4.43 NTSC is automatically selected.

NTSC: Specific selection of NTSC.

PAL: Specific selection of PAL.

SECAM: Specific selection of SECAM.

PAL-60: Specific selection of PAL60.

4.43NTSC: Specific selection of 4.43 NTSC.

User Manual BDL4251V

CONFIGURATION RESET

Selecting the CONFIGURATION RESET allows you to reset all configuration settings.

Select "Yes" and press "SET" button to restore the factory preset data.

Press " EXIT " button to cancel and return the previous menu.

FACTORY RESET

Selecting "YES" allows you to reset PICTURE, SCREEN, AUDIO, CONFIGURATION1,2 and

ADVANCED OPTION will be back to factory settings (except LANGUAGE, DATE AND TIME and

SCHEDULE).

Select "YES" and press "SET" button to restore the factory preset data. Press " EXIT " button to

cancel and return the previous menu.

User Manual BDL4251V

Main-Menu

CONFIGURATION 2

OSD TURN OFF

The OSD control menu will stay on as long as it is used. In the OSD Turn Off submenu, you can select

how long the monitor waits after the last touch of a button to shut off the OSD control menu.

The preset choices are 5 -120 seconds.

INFORMATION OSD

Selects the information OSD to be displayed or not.

The information OSD will be displayed when the input signal is changed or a source change or warning

message like no-signal or out-of range.

A time between 1 to 10 seconds is available.

SLEEP TIMER

To select SLEEP TIMER mode ON/OFF.

In the SLEEP TIMER menu, you can preset the monitor to automatically power down.

A time between 1 to 24 hours is available.

When the SLEEP TIMER is set, the SCHEDULE settings will be disabled.

OSD H POSITION

Adjusts the horizontal position of the OSD menu.

OSD V POSITION

Adjusts the vertical position of the OSD menu.

User Manual BDL4251V

MONITOR INFORMATION

Indicates the model and serial number of your monitor.

User Manual BDL4251V

Main-Menu

ADVANCED OPTION

INPUT RESOLUTION * : INPUT VGA only

This feature makes the display controlling the source in order to match display capabilities by choice or

automatically. You can select one of the following timings:

(1)1024x768, 1280x768, 1360x768 and 1366x768.

(2) 640x480, 720x480 and 852x480

(3) 800x600, 1064x600 and 720x576

(4) 1400x1050 and 1864x1050

(5) 720x400 and 640x400

AUTO: Determines the resolution automatically.

The setting you select becomes effective when POWER is turned OFF and ON again.

BLACK LEVEL EXPANSION * : INPUT HDMI, DVI-D(MODE-HD), S-VIDEO, VIDEO only

Selects a level of black expansion from “OFF”,”LOW”, “MIDDLE” and “HIGH”.

In case of go under the black cut-off level, please adjust the “Black level” in moderation on OSD menu.

GAMMA SELECTION

Selects a display gamma. It refers to the brightness performance curve of signal input.

2.2

2.4

S gamma

Native

NOTE: sRGB picture mode is standard and cannot be changed.

SCAN MODE * : INPUT HDMI, DVI-D(MODE-HD), S-VIDEO, VIDEO only

Changes the display area of the image.

OVERSCAN: Set to display area about 95%

UNDERSCAN: Set to display area about 100%

SCAN CONVERSION * : INPUT HDMI, DVI-D(MODE-HD), S-VIDEO, VIDEO only

Selects IP (Interlace to Progressive) converter function.

PROGRESSIVE: Enable the IP function, to convert interlace signal to progressive. Normally use

this setting.

INTERLACE*: Disable the IP function.

*NOTE: This mode is better suited for motion pictures, but it increases chance of image retention.

User Manual BDL4251V

FILM MODE * : INPUT HDMI, DVI-D(MODE-HD), S-VIDEO, VIDEO only

Selects Film mode function.

AUTO: Enable the Film mode function. This mode is better suited for movies, which is converted 24

Frames/sec source to DVD Video. We recommend to select “PROGRESSIVE” in “SCAN CONVERSION”.

OFF: Disable the Film mode function. This mode is better suited for Broadcasting or VCR source.

IR CONTROL

Selects the operation mode of the remote controller when multiple BDL4251V monitors are connected via

RS232C.

The item in this menu will become effective by pressing “SET” button on the selected item.

NORMAL: The monitor will be controlled normally by remote controller.

PRIMARY: The first BDL4251V monitor of those multi-connected via RS232C is designated as PRIMARY.

SECONDARY: BDL4251V monitors other than the first one multi-connected via RS232C are designated

as SECONDARY.

LOCK: Disable the monitor control by infrared remote controller.

Keep pressing “DISPLAY” button during 5 sec or more, this setting will return to “NORMAL”.

KEYBOARD CONTROL

Selects the operation mode of the keyboard control.

Select “LOCK” to disable the keyboard.

Select “UNLOCK” to enable the keyboard.

TILING

TILING demonstrates multiple screens. This feature provides a single large screen using up to 25 monitors.

It will be able to divide up to 5 each H and V.

This requires you to feed the PC output into each of the monitors through a distributor.

H MONITORS: Select number of horizontal monitors.

V MONITORS: Select number of vertical monitors.

POSITION: Select a position to expand the screen.

FRAME COMP: Works in tandem with TILING to compensate for the width of the tile bezels in order to

accurately display the image.

ENABLE: Select “YES”, the monitor will expand the selected position.

PIP and STILL will be disabled when “TILING” is activated.

HEAT STATUS * : Disclamer: Heat sensor is indicative.

HEAT STATUS allows you to watch the thermal status at any time via the OSD menu and/or via RS232C

commands. The indicated temperature has a accuracy of 3 degrees (plus and minus).

Press “SET” button to enter the submenu to monitor the heat status.

Press “EXIT” button to cancel and then return the previous menu.

DATE AND TIME

Adjusts the current date and time for internal clock.

You should set this function when you use “SCHEDULE”.

User Manual BDL4251V

SCHEDULE

Programs the monitor's working schedule.

Schedules the power on and power off by using hour and a day of the week. Also sets the input port.

This OSD can't be removed except EXIT.

MONITOR ID

ID numbers for remote control are assigned to BDL4251V monitors that are multi-connected via RS232C.

ID numbers 1 to 26 are selectable.

DDC/CI

Use to turn ON or OFF the DDC/CI communication function. Select ON for normal use.

SMART POWER

Selecting SMART POWER allows you to choose a certain level of power saving condition.

Select “OFF” to set the system in normal power condition

Select “MEDIUM” to set the system in medium level power saving status.

Select “HIGH” to set the system in high level power saving status

Press “EXIT” button to cancel and then return the previous menu.

ADVANCED OPTION RESET

Selecting ADVANCED OPTION RESET allows you to reset all OSD settings from ADVANCED OPTION

settings, except for GAMMA SELECTION, DATE AND TIME, SCHEDULE, HDMI INPUT MODE, DVI-D

INPUT MODE,MONITOR ID, and DDC/CI.

Select “YES” and press “SET” button to restore the factory preset data.

Press “EXIT” button to cancel and then return the previous menu.

GAMMA SELECTION is reset when carrying out the PICTURE RESET in the PICTURE.

User Manual BDL4251V

NOTE

NOTE 1: IMAGE PERSISTENCE

Please be aware that LCD Technology may experience a phenomena known as Image Persistence. Image Persistence occurs when residual or

“ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’

image persistence is not permanent, but constant images being displayed for a long period of time should be avoided.

To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an

image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

As with all personal display devices, PHILIPS recommends displaying moving images and using a moving panel saving at regular intervals

whenever the screen is idle or turning off the monitor when not in use.

Please set “POWER SAVE”, “PANEL SAVING”, “DATE AND TIME” and “SCHEDULE” functions to further reduce the risk of

Image persistence.

For long life use of Public Display

< Image Sticking of LCD Panel >

When LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or “ghost”

image of previous image may be observed. (Image Persistence)

Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along the

displayed image, and it is observed permanently. (Image Sticking)

< Recommendations >

For preventing the fast transition to Image Sticking, and for longer life usage of LCD, following are recommended.

1. Static images should not be displayed for long period. Always use a short cycle to change to other images.

2. In case a fixed image is displayed for a long period, it is advised to activate the pixel shift feature that will periodically move the image in four

directions

3. When not in use, please turn off the monitor with your remote control, or use Power Management Function or use the Schedule Function of

monitor.

4. Reducing the environmental temperature will increase the life of your monitor.

When Protection board (glass, acryl) is installed over the LCD surface, enclosed into the box / wall, or stack the monitor, please utilize the

temperature sensors inside monitor.

To reduce the environmental temperature, the monitor should be set Low Brightness or Cooling Fan “ON” by using Screen sever Function.

5. Please use "Panel saving Mode" of monitor.

NOTE 2: HOW TO SETUP SCHEDULE

Using the “SCHEDULE” function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated.

You can select the time the monitor turns on and turns off, the day of week the monitor is activated, and which input source the monitor will

use for each scheduled activation period. A check mark in the box next to the number of the schedule indicates that the selected schedule is in

effect.

To select which schedule to set, use the up/down arrows to move the number (1 to 7) of the schedule.

Use the (+) and (-) buttons to move the cursor horizontally within the particular schedule. Use the ( ) and ( ) buttons to increase time and

select input port. The “SET” button is used to make a selection.

If you create a schedule but do not want to use a power on time, select “--” in the “ON” time slot.

If you do not want to use a power off time select “--” in the OFF time slot.

If there is no input selected (“--” showing in the input spot) the input from the previous schedule will be used.

The selection of EVERY DAY within a schedule takes priority over other schedules that are set up to operate weekly. When schedules are

overlapping, scheduled Power ON time has priority over scheduled Power OFF time.

If there are two schedules programmed for the same time, then the highest numbered schedule has priority. When the “SLEEP TIMER” is set, the

“SCHEDULE” function is disabled.

User Manual BDL4251V

NOTE 3: “PIP”, “POP” and “SIDE BY SIDE”

The following table shows the combination of signal inputs under which the “PIP” and “POP” modes function. These modes do not function,

however, when the screen size is “CUSTOM” or “REAL”.

SUB

HDMI DVI-D VGA COMPONENT S-VIDEO VIDEO

HDMI      

DVI-D       : Supported

VGA       : Not supported

COMPONENT      

S-VIDEO      

MAIN

VIDEO      

Press the “PIP ON/OFF” buttons on the remote control to change between “PIP”, “POP” and “SIDE BY

SIDE” mode as shown in the diagram below.

PIP POP

SIDE BY SIDE

ASPECT

SIDE BY SIDE FULL

OFF

“PIP”, “POP” mode resolution (Reference)

PIP SIZE SMALL

MIDDLE

LARGE

POP SIZE

: 450 dots X 338 dots

: 675 dots X 450 dots

: 900 dots X 675 dots

: 450 dots X 338 dots

< Remote control numbering function >

By connecting multiple BDL4251V monitors using RS232C cables, you can control any one monitor or all the monitors by one remote controller.

1. Assign arbitrary ID number to each of multi-connected BDL4251V monitors using MONITOR ID. ID numbers 1

to 26 are selectable.

It is recommended to assign sequential ID numbers from 1 and up.

2. The remote control mode of the first BDL4251V monitor is set to PRIMARY and those of the other monitors are set to

SECONDARY.

3. When you direct the remote controller at the remote control signal sensor of the PRIMARY monitor and press the DISPLAY

button on the remote controller, the ID selection OSD appears at the upper left of the screen.

ID number of the currently viewed monitor

Select the ID number of the monitor you want to control using the +/- button

on the remote controller.

The ID of the monitor you want to control is displayed at the upper left of its screen.

By selecting ALL, you can control all the multi-connected monitors.

4. Direct the remote controller at the remote control signal sensor of the PRIMARY monitor. OSD appears

on the monitor having the ID number you selected.

NOTE:

When the ID selection OSD is being displayed on the PRIMARY monitor, press the DISPLAY button on the remote controller again to cancel the

ID selection OSD and then control the monitor you selected.

HINT:

If you set the remote control mode wrongly and remote control operation becomes unavailable, press MENU button on the control panel of the

monitor to display the OSD screen and change the remote control mode using ADVANCED OPTION. By pressing

and holding down the DISPLAY button on the remote control for 5 seconds or longer, the remote control mode is initialized to

NORMAL.

User Manual BDL4251V

Pixel defect policy BDL4251V

Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and

practice stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays

are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees

that any Plasma- & LCD- displays with an unacceptable number of defects will be repaired during the warranty period in line with

your local guarantee conditions.

This notice explains the different types of pixel defects and defines the acceptable defect level for the BDL4251V LCD screen. In

order to qualify for repair under warranty, the number of pixel defects must exceed a certain level which is given in the

reference table. If the LCD screen is within specification a warranty exchange / claim back will be refused. Additionally, because

some types or combinations of pixel defects are more noticeable than others, Philips sets even higher quality standards for those.

Pixels and Sub-pixels

A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and blue. Many pixels together

form an image. When all sub-pixels of a pixel are lit, the three colored sub-pixels together appear as a single white pixel. When

all are dark, the three colored sub-pixels together appear as a single black pixel. Other combinations of lit and dark sub-pixels

appear as single pixels of other colors.

Types of Pixel Defects + Dot definition

Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several

types of sub-pixel defects within each category.

Dot definition = What is a defective “Dot” ?

One or more defective, adjacent sub-pixel are defined as one “dot”. The no. of defective sub-pixels are not relevant to

define a defective dot. This means that a defective dot can consist of one, two or three defective sub-pixels which can

be dark or lit.

One dot = One Pixel; consists of three sub-pixels of Red; Green and Blue

Bright Dot Defects

Bright dot defects appear as pixels or sub-pixels that are always lit or "on". These are the examples of bright dot defects:

One lit red, green or blue sub-

pixel

Two adjacent lit sub-pixels:

- Red + Blue = Purple

- Red + Green = Yellow

- Green + Blue = Cyan (Light

Blue)

Three adjacent lit sub-pixels

(one white dot)

User Manual BDL4251V

Dark Dot Defects

Black dot defects appear as pixels or sub-pixels that are always dark or "off". These are the examples of black dot defects:

One dark dot Two adjacent dark dots=

1 pair of dark dots

Two dark dots, specifications

defines the minimum distance

between dark dots

Proximity of Pixel Defects

Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies

tolerances for the proximity of pixel defects. In the table below you can find specifications about:

 Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)

 Minimum distance between dark dots

 Total no. of all defective dots

Pixel Defect Tolerances

In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD-

display must have pixel or sub-pixel defects exceeding the tolerances listed in the following table.

BRIGHT DOT EFFECT ACCEPTABLE LEVEL

MODEL BDL4251V

1 lit sub pixel 1

BLACK DOT EFFECT ACCEPTABLE LEVEL

1 dark sub pixel 8

TOTAL DOT DEFECTS OF

ALL TYPES

Note:

* 1 or 2 adjacent sub pixel defects = 1 dot defect

User Manual BDL4251V

Features

Full HD LCD display 1920x1080p

This display has a resolution that is referred to as Full HD. The state-of-the-art LCD screen technology has the full high-definition widescreen

resolution of 1080 progressive lines, each with 1920 pixels. This allows the best possible picture quality for HD input signals with up to 1080

lines. It produces brilliant flicker-free progressive scan pictures with optimum brightness and superb colors. This vibrant and sharp image will

provide you with an enhanced viewing experience.

Slim bezel

A slim bezel design adds a stylish look to a public display to nicely blend in most environments. Furthermore this design is ideal for tiled matrix

video walls.

Zoom function for tiled matrix

The internal zoom function enables easy implementation of a video wall matrix, without the need for expensive external equipment. Capable of

a vidiwall of 25 displays by dividing up to 5 displays each horizontally and vertically.

High brightness

Allows daylight viewing even in large public environments with high ambient light conditions due to its 700 cd/m² high brightness professional

panel.

Network controllability: RS232C

Network controllability allows user to control and adjust monitors remotely through RS232C protocol.

Smart insert

Professional PC's are part of most public signage installations. Quite often they add additional depth to the public display and a lot of cable

clutter. This public display contains a Smart insert in the backcover that will fit many professional small form factor PC's. In addition it offers

provisions for efficient cable management.

SmartPower

The backlight intensity can be controlled and pre-set by the system to reduce the power consumption by up to 50%, which saves substantially

on energy costs.

Advanced anti image sticking

Static images left on-screen for extended periods of time may leave a "ghost image" or image sticking effect on LCD displays. Although image

sticking in LCD displays is not permanent, you want to prevent this to happen, especially in locations where content is shown 24/7.

Compliant with RoHS standards

Philips designs and produces display products in compliance with strict Restriction of Hazardous Substances (RoHS) standards that restrict lead

and other toxic substances that can harm the environment.

Automatic Long Cable Compensation:

Automatic long cable compensation prevents image quality degradation (color shift and dull signals) caused by long cable lengths.

User Manual BDL4251V

Troubleshooting

No picture

• The signal cable should be completely connected to the graphics card/computer.

• Front Power Switch and computer power switch should be in the ON position.

• Check to make sure that a supported mode has been selected on the graphics card or system being used.

(Please consult graphics card or system manual to change graphics mode.)

• Check the monitor and your graphics card with respect to compatibility and recommended settings.

• Check the signal cable connector for bent or pushed-in pins.

• If nothing is displayed on the screen when HDCP device is connected, reset the power of the device.

Power Button does not respond

• Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.

Image persistence

• Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a residual or

“ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but

constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the

previous image was displayed. For example,

if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

NOTE:

As with all personal display devices, PHILIPS recommends displaying moving images and using a moving panel saving at regular intervals whenever the

screen is idle or turning off the monitor when not in use.

Image is unstable, unfocused or swimming is apparent

• Signal cable should be completely attached to the computer.

• Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment. When the display mode is

changed, the OSD Image Adjust settings may need to be re-adjusted.

• Check the monitor and your graphics with respect to compatibility and recommended signal timings.

• If your text is garbled, change the video mode to non-interlace and use 60 Hz refresh rate.

Image of component signal is greenish

• Check to see if the COMPONENT input connector is selected.

LED on monitor is not lit (no green or red color can be seen)

• Power Switch should be in the ON position and power cord should be connected.

• Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).

RED LED on monitor is blinking

• A certain failure might have occurred, please contact your nearest authorized PHILIPS service facility.

Display image is not sized properly

• Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.

• Check to make sure that a supported mode has been selected on the graphics card or system being used.

(Please consult graphics card or system manual to change graphics mode.)

Selected resolution is not displayed properly

• Use OSD Display Mode to enter Information menu and confirm that the appropriate resolution has been selected.

If not, select corresponding option.

User Manual BDL4251V

No Sound

• Check to see if speaker cable is properly connected.

• Check to see if mute is activated.

• Check to see if volume is set at minimum.

Remote Control does not work

• Check the Remote Control’s batteries status.

• Check if batteries are inserted correctly.

• Check if the Remote Control is pointing at the monitor’s remote sensor.

“SCHEDULE” / “SLEEP TIMER” function is not working properly

• The “SCHEDULE” function will be disabled when the “SLEEP TIMER” is set.

• If the “SLEEP TIMER” function is enabled and the power to the LCD monitor is turned off if the power supply is interrupted unexpectedly, then

the “SLEEP TIMER” will be reset.

Stripe Noise

Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or degradation.

“NO SIGNAL” is displayed on the screen

Image may not be displayed right after HDCP device is connected.

User Manual BDL4251V

Specifications

Specifications (BDL4251V)

Product Specifications

Analog Input Digital Input

LCD

Module

Diagonal:

Pixel

itch:

Resolution:

Color:

Brightness:

Contrast

Ratio:

Response

time:

iew

Angle:

42"

106.7

0.485

1920

1080

dots

1.07

billion

colors

(depending

video

car

used)

700

cd/m

(typ.)

1,000:1

(typ.) , 3,000:1witch Smart Contrast

(typ.

and

Down

178°,

Left

and

Right

178°

(typ.)

@CR>10

equency

Horizontal:

ertical:

15.625

15.734,

kHz

50.0

58.0

75.0

Pixel

Clock

13.5

-165.0

MHz

25.0

-165.0

MHz

iewable

Size

930.25 x 523.25

36.6

20.6

inches

Input

Signal

PC-Input:

ideo:

Sync:

Input-terminal:

VIDEO

Input:

AUDIO

Input:

RS232C:

In:

Analog

RGB

ideo:

0.7

Vp-p

TMDS

Input

impedance

ohm

Separate

sync:

TTL

level

(Pos./Neg.),

Input

Impedance

2.2K

ohm

Mini

D-sub

HDMI

Composite:

1.0

Vp-p

Input

impedance

75ohm

BNC

and

RCA-PINJACK-INPUT

Y/C

Vp-p

0.286

Vp-p

Input

Impedance

ohm

S-TERMINAL-INPUT

Component:

1.0

0.7

Vp-p

Input

Impedance

ohm

BNC-INPUT

RCA

PIN-JACK

L/R

INPUT

STEREO

Mini

Jack

INPUT

Mini

D-sub

Output

Signal

PC-Output:

ideo:

Sync:

Output-terminal:

VIDEO

Output:

AUDIO

Output:

Speaker

Output:

RS232C:

Out:

Analog

RGB

ideo:

0.7

Vp-p

with

ohm

terminated

Separate

sync:

TTL

level

(Pos./Neg.)

Mini

D-sub

BNC-OUTPUT

Composite

1.0

Vp-p

with

ohm

terminated

RCA

PIN-JACK

L/R

OUTPUT

0.15

rms

with

47k

ohm

terminated

Internal Speaker

ohm)

External

Speaker

Jack

ohm)

Mini

D-sub

Resolutions

Supported

640

480

800

600

60Hz

1024

768

60Hz

1280 x 720 at 60Hz

1280

768

60Hz

1360

768

60Hz

1600

1200

1900x1200 (reduced Blanking only)

1920

1080

60Hz*

Recommended

Resolution

NTSC,P

AL,SECAM,4.43NTSC,PAL60

DVD:480i,480p,

576i,720p,1080i,1080p

Power

Supply

2.4

–

1.2

@100

240

AC,

Power

Consumption

Power

Save:

Typically

232

Less than 1W (Power button off or main power switch off.)

Operational

emperatur

Envir

onment

Humidity:

Landscape:

°C

41-104

Portrait

°C

°F

(Without

condensation)

Storage

emperatur

Envir

onment

Humidity:

-20

°C

-4

140

°F

90%

(Without

condensation)/90%-3.5%x(T

mp-40°C)

egar

ding

over

40°C

Dimension

Net

without

stand:

Net

with

stand:

oss:

967.6

(W)

559.6

(H)

123.1

(D)

38.09"

(W)

22.03"

(H)

4.85"

(D)

967.6

(W)

x605.6

(H)

405

(D)

38.09"

(W)

23.84"

(H)

15.95"

(D)

1170

(W)

715

(H)

286

(D)

70.87"

(W)

x28.15"

(H)

x11.26"

(D)

eight

Net

without

stand:

Net

with

stand:

oss:

48.5lbs

52.47

lbs

23.8

68.78

lbs

31.2kg

Wall

mounting

interface

Holes

(400

pitches)

Optional

Multi-purpose

Fix

Mount

Complied

Regulatory

and

Guidelines

UL60950-1/C-UL/EN60950-1/FCC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3 /CE

Power

Management

Support VESA DPMS convention

Plug

Play

VESA

DDC2B,

DDC/CI

Accessories

CD User's

Manual, QSG, Power

Cor

VGA

Cable,

BNC TO RCA adapter x 5,

Remote

Contr

oller

AAA

Battery

2, Clamper

event

from

falling),

Cable belt x 3

(For

securing

cables),

Screw

for

Main

switch

cover

Screw

for

CLAMPER

Cable

Holder

2, Main

switch

cover.

Note:

echnical

specifications

subject

change

without

notice.

User Manual BDL4251V

Name

ideo

Signal

Red

ideo

Signal

Green

ideo

Signal

Blue

GND

DDC-GND

6 Red-GND

een-GND

8 Blue-GND

+5V

(DDC)

SYNC-GND

GND

DDC-SDA

13 H-SYNC

-SYNC

15 DDC-SCL

Assignment

HDMI

connector:

TMDS

Data2+

TMDS

Data0

Shield 15

SCL

TMDS

Data2

Shield 9

TMDS

Data0-

SDA

TMDS

Data2-

TMDS

Clock+

DDC/CEC

ound

TMDS

Data1+

TMDS

Clock

Shield 18

+5V

Power

TMDS

Data1

Shield 12

TMDS

Clock-

Hot

Plug

Detect

TMDS

Data1-

CEC

TMDS

Data0+

Reserved

(N.C.

device)

Name

1 NC

RXD

TXD

4 NC

GND

6 NC

CTS

9 NC

Pin Assignment

1) Analog Video Signal Input (Mini D-SUB 15P): VGA

Mini D-SUB 15P

5 6

10 11

2) S-VIDEO input (MINI DIN 4P): S-VIDEO

3) HDMI:

MINI DIN 4P

4) RS232C input/output

Mini D-SUB 9P

2 18

HDMI

Pin No Name

1 GND

2 GND

3 Y (Luminance)

4 C (Chroma)

User Manual BDL4251V

Philips and the Philips Shield Emblem are registered trademarks of

Koninklijke Philips Electronics N.V. and are used under license from

Koninklijke Philips Electronics N.V.

Specifications are subject to change without notice.

Philips BDL4251V/00 User Manual

Related Manuals

EXIT 41.00.20.00 Manual

EXIT 30.00.32.00 Manual

EXIT 30.00.32.00 Manual

Bourgini 23.1019.00.00 Manual

Philips HP6350/00 Manual

Philips HD6161/00 Manual

Philips AE2160/00C Manual

Philips SPC900NC/00 Manual