Table of Contents
Philips BT110A/00 User Manual
Displayed below is the user manual for BT110A/00 by Philips which is a product in the Portable Speakers category. This manual has pages.
Related Manuals
BT110
Register your product and get support at
www.philips.com/support
User manual
Portable speaker
1EN
Contents
1 Important 2
2 Your portable speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 4
3 Get started 5
Attach the string 5
Charge the built-in battery 5
Turn on/o 5
4 Play from Bluetooth devices 6
Connect a device 6
Disconnect a device 7
Reconnect a device 7
Connect another device 7
5 Play from external devices 8
6 Product information 9
Audio 9
Speaker 9
Bluetooth 9
General information 9
7 Troubleshooting 10
General 10
About Bluetooth device 10
8 Notice 11
Compliance 11
Care of the environment 11
Trademark notice 12
2EN
1 Important
Warning
•Never remove the casing of this product.
•Never place this product on other electrical
equipment.
•Keep this product away from direct
sunlight, naked ames or heat.
• Read these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not install near any heat
sources such as radiators, heat
registers, stoves, or other apparatus
(including ampliers) that produce
heat.
• Only use attachments/accessories
specied by the manufacturer.
• The battery shall not be exposed
to excessive heat such as sunshine,
re or the like.
• Do not place any sources of
danger on the product (e.g. lighted
candles).
• The operation temperature of the
product is from -10 °C to 40 °C.
• The product supports USB V2.0 or
V1.1 only.
Note
•The type plate is located on the bottom of
the product.
3EN
2 Your portable
speaker
Congratulations on your purchase,
and welcome to Philips! To fully
benet from the support that Philips
oers, register your product at
www.philips.com/welcome.
Introduction
This speaker has passed splash-proof
test (IPX4) and can be used near water.
With this speaker, you can enjoy audio
from Bluetooth-enabled devices or
other external devices.
What's in the box
Check and identify the contents of your
package:
• Speaker
• USB cable for charging
• String for carrying
• Printed materials
4EN
Overview of the speaker
a
• Enter Bluetooth pairing mode.
• After Bluetooth connection,
respond to a call.
• Clear Bluetooth pairing
information.
b
• Turn the speaker on or o.
c LED indicator
• Indicate battery or Bluetooth
connection status.
d AUDIO IN
• Connect an external audio
device.
e DC IN
• Recharge the built-in battery.
a
d
e
b
c
5EN
3 Get started
Always follow the instructions in this
chapter in sequence.
Attach the string
For easy carrying, attach the supplied
string to this speaker as illustrated.
Charge the built-in
battery
The speaker is powered by a built-in
rechargeable battery.
Note
•Before use, fully charge the built-in battery.
•The micro USB socket is for charging only.
•It takes you approximately four hours to
fully charge the battery.
•Rechargeable battery has a limited number
of charge cycles. Battery life and number of
charge cycles vary by use and settings.
Connect the USB cable between
• the DC IN socket on the speaker,
and
• a USB socket on a computer.
The LED indicator indicates the battery
status.
Battery Status LED Indicator
Under
charging
Red
Fully charged/
Not charging
O (in power-o
mode);
Blue (in Bluetooth
mode)
Low battery Flashing red
Turn on/o
Press and hold for three seconds to
turn the speaker on or o.
» When the speaker is turned on,
the LED indicator begins to ash.
» When the speaker is turned o,
the LED indicator lights o.
Note
•The speaker switches to standby mode
automatically when being idle for 15
minutes.
6EN
4 Play from
Bluetooth
devices
With this speaker, you can listen to
audio from Bluetooth-enabled devices.
Connect a device
Note
•The speaker can memorize a maximum of
four paired devices. The fth paired device
will replace the rst one.
•Any obstacle between this speaker
and a Bluetooth device can reduce the
operational range.
•Keep away from any other electronic
device that may cause interference.
•The operational range between this
speaker and a Bluetooth device is
approximately 20 meters.
1 Make sure that the speaker is in
Bluetooth pairing mode
• For rst-time use, the
speaker enters pairing mode
automatically.
• If the speaker has been paired
with other device before, press
and hold on the speaker for
two seconds to enter pairing
mode.
» The LED indicator ashes blue
quickly.
2 On your Bluetooth device, enable
Bluetooth and search for Bluetooth
devices that can be paired (refer to
the user manual of the device).
3 Select [Philips BT110] displayed
on your device for pairing and
connection. If necessary, input
“0000” as the pairing password.
» After successful pairing and
connection, the speaker beeps
twice, and the LED indicator
turns solid blue.
LED Indicator
(blue)
Bluetooth Connection
Status
Quick ashing
(2Hz)
Pairing
Slow ashing
(1Hz)
Connecting
Solid blue Connected
2 sec
.
Philips BT110
7EN
Play from a Bluetooth-enabled
device
Note
•Music play pauses when there is an
incoming call, and resumes when your
phone call ends.
After successful Bluetooth connection,
play music on the connected Bluetooth
device.
» Music streams from your Bluetooth
device to the speaker.
Tip
•You can use your Bluetooth device to
control play.
Control your phone call
After Bluetooth connection, you can
control an incoming call with this
speaker.
Button Function
Press to answer an incoming
call.
Press and hold for two
seconds to reject an incoming
call.
During a call, press to end the
current call.
During a call, press and hold
for two seconds to transfer
the call between your mobile
device and the speaker.
Disconnect a device
• Press and hold for two seconds;
• Turn o the speaker;
• Disable Bluetooth on your device;
or
• Move the device beyond the
communication range.
Reconnect a device
• When you turn on the speaker, it
will reconnect the last connected
device automatically;
• If not, select [Philips BT110] on
your Bluetooth menu to start
reconnection.
Connect another device
1 Press and hold for two seconds to
disconnect the currently connected
device;
» The speaker enters Bluetooth
pairing mode.
2 Connect another Bluetooth device.
8EN
5 Play from
external devices
With this speaker, you can also listen
to an external audio device such as an
MP3 player.
Note
•Make sure that music playback through
Bluetooth is stopped.
1 Connect an audio input cable (not
supplied) with a 3.5 mm connector
on both ends to
• the AUDIO IN socket on this
speaker, and
• the headphone socket on the
external device.
2 Play audio on the external device
(refer to its user manual).
» The speaker switches to the
AUDIO IN mode.
Tip
•When you start music streaming from
a connected Bluetooth device, the
speaker switches to the Bluetooth source
automatically.
9EN
6 Product
information
Note
•Product information is subject to change
without prior notice.
Audio
Rated Output
Power
4W RMS at 1%
THD
Frequency
Response
80 -16000 Hz
Signal to Noise
Ratio
>72 dBA
Audio-in Input 600mV RMS
20kohm
Speaker
Speaker Impedance 4 ohm
Speaker Driver 40mm full range
drivers
Sensitivity 80±3dB/m/W
Bluetooth
Bluetooth Version V4.0
Bluetooth Prole A2DP:1.2; HFP: 1.5;
AVRCP:1.4
Frequency band/
Output power
2.400GHz -
2.483GHz ISM
Band / ≤ 4dBm
(Class 2)
Bluetooth
Distance Range
20 m
General information
DC Power (Supply
Input)
5 V, 1 A
Built-in Battery 3.7 V, 800 mAh
Dimensions - Main
Unit (W x H x D)
98 x 77 x 35
mm
Weight - Main Unit 0.15 kg
10 EN
7 Trouble-
shooting
Warning
•Never remove the casing of this device.
To keep the warranty valid, never try to
repair the system yourself.
If you encounter problems when using
this device, check the following points
before requesting service. If the problem
remains unsolved, go to the Philips Web
page (www.philips.com/support). When
you contact Philips, make sure that the
device is nearby and the model number
and serial number are available.
General
No power
• Recharge your speaker.
No sound
•Adjust volume on the connected
device.
•In AUDIO IN mode, make sure that
music playback through Bluetooth
is stopped.
•Make sure that your Bluetooth
device is within the eective
operational range.
No response from the speaker
•Recharge the speaker.
About Bluetooth device
The audio quality is poor after
connection with a Bluetooth-enabled
device.
•The Bluetooth reception is poor.
Move the device closer to this
product or remove any obstacle
between them.
Fail to nd [Philips BT110] on your
device for pairing.
•Press and hold for two seconds
to enter pairing mode, and then try
again.
Cannot connect with the device.
•The Bluetooth function of the
device is not enabled. Refer to the
user manual of the device for how
to enable the function.
•This product is already connected
with another Bluetooth-enabled
device. Disconnect that device and
then try again.
The paired device connects and
disconnects constantly.
•The Bluetooth reception is poor.
Move the device closer to this
product or remove any obstacle
between them.
•For some devices, Bluetooth
connection may be deactivated
automatically as a power-saving
feature. This does not indicate any
malfunction of this product.
11EN
8 Notice
Any changes or modications made
to this device that are not expressly
approved by Gibson Innovations may
void the user’s authority to operate the
equipment.
Compliance
Hereby, Gibson Innovations declares
that this product is in compliance
with the essential requirements
and other relevant provisions of
Directive 2014/53/EU. You can nd
the Declaration of Conformity on
www.philips.com/support.
This product is designed to be
waterproof in compliance with IEC
60529 IPX4.
Care of the environment
Disposal of your old product and
battery
Your product is designed and
manufactured with high quality
materials and components, which can
be recycled and reused.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This symbol means that the product
contains a built-in rechargeable
battery covered by European Directive
2013/56/EU which cannot be disposed
of with normal household waste. We
strongly advise you to take your product
to an ocial collection point or a Philips
service centre to have a professional
remove the rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and
never dispose of the product and
rechargeable batteries with normal
household waste. Correct disposal of
old products and rechargeable batteries
helps prevent negative consequences
for the environment and human health.
Caution
•Removal of the built-in battery invalidates
the warranty and may destroy the product.
Always bring your product to a
professional to remove the built-in
battery.
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
12 EN
foam (buer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials
which can be recycled and reused
if disassembled by a specialized
company. Please observe the local
regulations regarding the disposal
of packaging materials, exhausted
batteries and old equipment.
Trademark notice
The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Gibson Innovations Limited
is under license. Other trademarks
and trade names are those of their
respective owners.
13EN
2016 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd.,
and Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are
used under license.
BT110_00 _UM_V3.0