Table of Contents
Philips BT6000R/10 User Manual
Displayed below is the user manual for BT6000R/10 by Philips which is a product in the Portable Speakers category. This manual has pages.
Related Manuals
BT6000
Register your product and get support at
www.philips.com/support
User manual
Portable speaker
1EN
Contents
1 Important 2
2 Your Bluetooth speaker 2
Introduction 2
What's in the box 3
Overview of the speaker 3
3 Get started 4
Power supply 4
Turn on/o 4
Adjust volume 5
4 Use Bluetooth devices 5
Connect a device 5
Play from Bluetooth device 6
Control your phone call 6
Disconnect a device 7
Reconnect a device 7
5 Listen to an external device 8
6 Specications 8
7 Trou bl e shooting 9
General 9
About Bluetooth device 10
8 Notice 10
Compliance 10
Care of the environment 10
Trademark notice 11
2EN
1 Important
Warning
•Never remove the casing of this speaker.
•Never place this speaker on other electrical
equipment.
•Keep this speaker away from direct
sunlight, naked ames or heat.
•Make sure that you always have easy
access to the power cord, plug, or adaptor
to disconnect the speaker from the power.
• Make sure that there is enough
free space around the speaker for
ventilation.
• After use under humid
circumstance, immediately clean
the product with a soft dry cloth.
• The battery shall not be exposed
to excessive heat such as sunshine,
re or the like.
• The adapter shall not be exposed
to dripping or splashing.
• No objects lled with liquids shall
be placed on the adapter.
• Do not place any sources of
danger on the speaker (e.g. lighted
candles).
• Use only power supplies listed in
the user manual.
• Where the plug of the Direct Plug-in
Adapter is used as the disconnect
device, the disconnect device shall
remain readily operable.
Note
• The type plate is located on the bottom
of the speaker.
2 Your
Bluetooth
speaker
Congratulations on your purchase,
and welcome to Philips! To fully
benet from the support that Philips
oers, register your product at
www.philips.com/welcome.
Introduction
This speaker has passed splash-proof
test (IPX4) and can be used near water.
With this speaker, you can enjoy audio
from Bluetooth-enabled devices or
other external devices.
3EN
What's in the box
Check and identify the contents of your
package:
• Speaker
• USB cable for charging
• USB adapter
• Printed materials
Quick Start Guide
Overview of the speaker
3 4
2 1
5
a /PAIRING
• Enter Bluetooth pairing mode.
• After Bluetooth connection,
respond to an incoming call.
• Clear Bluetooth pairing
information.
b NFC
• Connect a NFC compatible
device through Bluetooth.
c
• Charge the built-in battery.
d AUDIO IN
• Connect an external audio
device.
e Volume knob ( )
• Turn the speaker on or o.
• Adjust volume.
4
3 Get started
Always follow the instructions in this
chapter in sequence.
Power supply
Either AC power or the built-in battery
can be used as power supply of this
product.
Option 1: AC power
Caution
•Risk of product damage! Make sure that the
power voltage corresponds to the voltage
printed on the back or underside of the
speaker.
•Risk of electric shock! When you unplug the
AC adapter, always pull the plug from the
socket. Never pull the cord.
Connect the adapter to:
• the socket on the speaker.
• the power outlet.
Option 2: Battery power
The speaker can also operate on the
built-in rechargeable battery.
Note
•Rechargeable battery has a limited number
of charge cycles. Battery life and number of
charge cycles vary by use and settings.
•It takes approximately three hours to fully
charge the battery.
•The red LED indicator ashes when the
battery is low.
To recharge the built-in battery:
• Connect the speaker to AC power.
Battery indicator Battery status
Solid red Under charging
O Fully charged
Turn on/o
OFF
ON
EN
5
To turn the speaker on or o, rotate the
knob clockwise or anticlockwise until
you hear a click.
» When the speaker is turned on, the
blue LED indicator ashes.
» When the speaker is turned o, the
blue LED indicator lights o.
Note
•If the battery level is low, the red LED
indicator ashes.
•The speaker turns o automatically when
being idle for 15 minutes.
Adjust volume
During music playback, rotate the knob
to increase or decrease volume.
4 Use
Bluetooth
devices
With this speaker, you can listen to
audio from Bluetooth-enabled devices
and control the incoming call through
Bluetooth.
Connect a device
Note
•Make sure that Bluetooth function is
enabled on your device, and your device is
set as visible to all other Bluetooth devices.
•Any obstacle between this speaker
and a Bluetooth device can reduce the
operational range.
•Keep away from any other electronic
device that may cause interference.
•The operational range between this
speaker and a Bluetooth device is
approximately 10 meters (30 feet).
Option 1: Connect a device
through NFC
Near Field Communication (NFC) is a
technology that enables short-range
wireless communication between
various NFC compatible devices, such
as mobile phones and IC tags.
If your Bluetooth device supports NFC,
you can connect it with this speaker
easily.
1 Enable NFC on your Bluetooth
device (refer to its user manual).
2 Turn on the speaker.
» The blue LED indicator ashes.
EN
6
3 Tap the NFC tag on the top of the
speaker with the NFC area of your
Bluetooth device.
4 Follow the on-screen instructions
to complete the pairing and
connection.
» After successful connection, the
speaker beeps twice, and the
LED indicator turns solid blue.
Option 2: Connect a device
manually
1 On your Bluetooth device, enable
Bluetooth and search for Bluetooth
devices that can be paired (see the
user manual of the device).
2 Turn on the speaker.
» The blue LED indicator ashes.
3 Select [Philips BT6000] displayed
on your device for pairing. If
necessary, input “0000” as the
pairing password.
» After successful connection, the
speaker beeps twice, and the
LED indicator turns solid blue.
• If you fail to nd [Philips
BT6000] on your device
for pairing, press and hold
/PAIRING for three seconds
until you hear beep sound, and
then try again.
LED indicator
(blue)
Description
Flashing quickly Ready for pairing
Flashing slowly Connecting
the previously
connected device
Solid blue Connected
Play from Bluetooth
device
Note
•Music play pauses when there is an
incoming call, and resumes when your
phone call ends.
After successful Bluetooth connection,
play audio on the Bluetooth device.
» Audio streams from your Bluetooth
device to the speaker.
Control your phone call
After Bluetooth connection, you can
control an incoming call with this
speaker.
EN
7
Button Function
/PAIRING Press to answer an
incoming call.
Press and hold for three
seconds to reject an
incoming call.
During a call, press to end
the current call.
During a call, press and
hold for three seconds to
transfer the call to your
mobile device.
Disconnect a device
• Press and hold /PAIRING for three
seconds when there is no incoming
call;
• Disable Bluetooth on your device;
or
• Move the device beyond the
communication range.
» The speaker beeps, and the blue
LED indicator ashes.
Note
•Before connecting another Bluetooth
device, disconnect the current device rst.
Reconnect a device
• When you turn on the speaker,
it tries to reconnect the last
connected device automatically;
• If not successful, select [Philips
BT6000] on your Bluetooth menu
to start reconnection.
Clear pairing information
Press and hold /PAIRING for 8 seconds.
EN
8
5 Listen to
an external
device
With this speaker, you can also listen
to an external audio device such as an
MP3 player.
Note
•Make sure that music playback through
Bluetooth is stopped.
1 Open the protective cover on the
left of the speaker.
2 Connect an audio input cable (not
supplied) with a 3.5 mm connector
on both ends to
• the AUDIO IN socket on this
speaker, and
• the headphone socket on the
external device.
3 Play audio on the external device
(refer to its user manual).
Tip
•When you start music streaming from
a connected Bluetooth device, the
speaker switches to the Bluetooth source
automatically.
6 Specications
Note
•Product information is subject to change
without prior notice.
Rated output
power
(Amplier)
12W RMS
Acoustic
frequency
response
100-20000 Hz
Speaker driver 2 x 1.5” full range, 8 Ω
Bass
enhancement
2 x passive radiator
Bluetooth
version
V4.0
Bluetooth
supported
proles
HFP V1.5, A2DP V1.2,
AVRCP V1.4
Bluetooth
frequency band
/ Output power
2.400GHz ~
2.483GHz ISM Band /
≤ 4dBm (Class 2)
NFC frequency 13.56 MHz
AUX input level 650mV RMS
Water
resistance
IPX4
Power Supply
- AC Power
(power
adapter)
Brand name:
PHILIPS;
Model: AKN2G-
0500200VU;
Input: 100-240 V~,
50/60 Hz, 0.35 A;
Output: 5 V 2 A;
- Built-in
battery
Li-ion battery
(3.7 V, 4400 mAh)
Play time in
battery mode
Approx. 8 hours
EN
9
Standby Power
Consumption
< 1 W
Eco Standby
Power
Consumption
< 0.5 W
Dimensions
- Main unit
(W x H x D)
188 x 71 x 70 mm
Weight
- Main unit 0.5 kg
7 Trou bl e -
shooting
Warning
•Never remove the casing of this device.
To keep the warranty valid, never try to
repair the system yourself.
If you encounter problems when using
this device, check the following points
before requesting service. If the problem
remains unsolved, go to the Philips Web
page (www.philips.com/support). When
you contact Philips, make sure that the
device is nearby and the model number
and serial number are available.
General
No power
•Make sure that the AC power
plug of the speaker is connected
properly.
•Make sure that there is power at the
AC outlet.
•Recharge your speaker.
No sound
•Adjust volume on this product.
•Adjust volume on the connected
device.
•Make sure that your Bluetooth
device is within the eective
operational range.
No response from the speaker
•Disconnect and reconnect the
power plug, then turn on the
speaker again.
•Recharge the speaker.
EN
10
The LED indicator is solid red, and
the speaker has no response when
pressing any key.
•The speaker is in DEMO mode. To
exit this mode: after connecting
to AC power, press and hold
/PAIRING, turn on the speaker,
then release the /PAIRING key
after 15 seconds.
About Bluetooth device
The audio quality is poor after
connection with a Bluetooth-enabled
device.
•The Bluetooth reception is poor.
Move the device closer to this
product or remove any obstacle
between them.
Fail to nd [Philips BT6000] on your
device for pairing.
•Press and hold /PAIRING for three
seconds, and then try again.
Cannot connect with the device.
•The Bluetooth function of the
device is not enabled. Refer to the
user manual of the device for how
to enable the function.
•This product is already connected
with another Bluetooth-enabled
device. Disconnect that device and
then try again.
The paired device connects and
disconnects constantly.
•The Bluetooth reception is poor.
Move the device closer to this
product or remove any obstacle
between them.
•For some devices, Bluetooth
connection may be deactivated
automatically as a power-saving
feature. This does not indicate any
malfunction of this product.
8 Notice
Any changes or modications made
to this device that are not expressly
approved by Gibson Innovations may
void the user’s authority to operate the
equipment.
Compliance
Hereby, Gibson Innovations declares
that this product is in compliance
with the essential requirements
and other relevant provisions of
Directive 2014/53/EU. You can nd
the Declaration of Conformity on
www.philips.com/support.
Care of the environment
Disposal of your old product and
battery
Your product is designed and
manufactured with high quality
materials and components, which can
be recycled and reused.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This symbol means that the product
contains a built-in rechargeable
battery covered by European Directive
2013/56/EU which cannot be disposed
EN
11
of with normal household waste. We
strongly advise you to take your product
to an ocial collection point or a Philips
service centre to have a professional
remove the rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and
never dispose of the product and
rechargeable batteries with normal
household waste. Correct disposal of
old products and rechargeable batteries
helps prevent negative consequences
for the environment and human health.
Caution
•Removal of the built-in battery invalidates
the warranty and may destroy the product.
Always bring your product to a
professional to remove the built-in battery.
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials
which can be recycled and reused
if disassembled by a specialized
company. Please observe the local
regulations regarding the disposal
of packaging materials, exhausted
batteries and old equipment.
Trademark notice
The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Gibson Innovations Limited
is under license. Other trademarks
and trade names are those of their
respective owners.
The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the
United States and in other countries.
This is CLASS II apparatus with double
insulation, and no protective earth
provided.
EN
Copyright © 2016 Gibson Innovations Limited. Revised Edition © 2017
This product has been manufactured by, and is sold under the responsibility of Gibson
Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips
N.V. and are used under license.
BT6000MKII_12 _UM_V2.0