Philips D4002W/53 User Manual
Displayed below is the user manual for D4002W/53 by Philips which is a product in the Telephones category. This manual has pages.
Related Manuals
D400
D405
Register your product and get support at
www.philips.com/welcome
Short user manual
05.en
Important safety
instructions
Warning
•The Electrical network is classified as hazardous.
The only way to power down the charger is to
unplug the power supply from the electrical outlet.
Ensure that the electrical outlet is always easily
accessible.
•Refer to safety information before using the
product.
•This product complies with European R&TTE
directive 1999/5/EC.
•Use only the power supply listed in the user
instructions.
•Use only the batteries listed in the user instructions.
•Do not allow the product to come into contact
with liquids.
•Risk of explosion if battery is replaced by an
incorrect type.
•Dispose of used batteries according to the
instructions.
•When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.
1Overview
Display icons
It displays the connection between the handset
and the base. The more bars are shown, the
better the signal strength is.
It remains steadily on when browsing incoming
calls in the call log.
It indicates an outgoing call in the redial list.
Itasheswhenthereisanewmissedcallor
when browsing new missed calls. It remains
steadily on when browsing the missed calls in
call log that are already read.
Itasheswhenreceivingincomingcall.Itremains
steadily on during a call.
The speaker is on.
The ringer is off. The silent mode is set and
within active period (the phone does not ring).
The silent mode is set, but is outside of active
period.
The alarm is activated.
D405only:Answeringmachine:itasheswhen
there is a new message. It remains steadily
on when the telephone answering machine is
turned on.
Voicemessagesindicator:ashesfornew
messages, is steady for reviewed messages.
* This is network dependent
It displays when you scroll up/down a list or
increase and decrease the volume.
ECO
The ECO mode is activated.
ECO+
The ECO+ mode is activated.
In call
Enter the option menu.
Adjust the volume.
End calls.
Turn the speaker on/off.
Mute/unmute the microphone.
Enter a pause.
In menu
Conrm/Entertheoptionmenu./Select
Cancel
Up / down
Exit menu.
Standby
Access the main menu.
Phonebook
Call log
Make and receive calls.
Make intercom call.
Lock/unlock the keypad.
Make and receive calls through the speaker.
In text input
Delete text
Enter a space.
Switch upper/lower case.
Microphone
Earpiece
Loudspeaker
(back side)
Display icons
D405
Find
handset
/
/
Loudspeaker
(back side)
D400
1 2 3
2Connect
Multi-handset version
only.
3Get started
Insert batteries Charge your phone
Charge 8 hours
Congure your phone
1 Whenusingyourphoneforthersttime,youseea
welcome message (country dependent).
2 Set the country and language if prompted.
3 Set the date and time.
•If the time is in 12-hour format, press / to select
[am] or [pm] (country dependent).
> 70%
40% - 70%
10% - 40%
< 10%
Flashing: low battery
Scrolling: charging in progress
4Enjoy
Phonebook
Add record
1 Press .
2 Select [Phonebook] > [Add new].
3 Follow on-screen instructions.
Call from the phonebook
1 Press .
2 Select a record and press .
Direct access memory
You have 2 direct access memories (Keys 1 and 2).
To dial the saved phone number automatically, press
and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to [1_voicemail] (voice mail number) and
[2_info svc] (information service number) of your
network operator respectively (network dependent).
Call log
Call from the call log
1 Press .
2 Select a record and press .
Save record
1 Press > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > [Delete].
2 Follow on-screen instructions.
Redial list
Call from the redial list
1 Press .
2 Select a record and press .
Save record
1 Press > > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > > [Delete].
2 Follow on-screen instructions.
Record an announcement
(for D405 only)
1 Press .
2 Select [Answ. Machine] > [Announcement].
3 Follow on-screen instructions.
Register additional handsets
You can register additional handsets to the base
station.
1 Press .
2 Select [Services] > [Register], then press
toconrm.
3 Press and hold on the base station for 5 seconds.
4 Enter the system PIN/passcode (0000).
5 Press toconrmthePIN/passcode.
» Registration is complete in less than 2 minutes.
Restore default settings
You can reset your phone settings to the original
factory settings.
1 Press .
2 Select [Services] > [Reset], then press to
conrm.
3 Follow on-screen instructions.
Note
•You may recall the original PIN/passcode by
following this procedure.
Technical data
Battery
•Philips: 2 x AAA NiMH 1.2 V Rechargeable
550 mAh batteries
Use only the supplied batteries.
Adapter
Base and charger:
Philips: S003IB0600040 SSW-1920UK-2
Input: 100-240 V
50/60 Hz 150 mA
100-240 V
50/60 Hz 200 mA
Output: 6 V 400 mA 6 V 500 mA
Phonebook with 100 entries
Call log with 50 entries
Talk time: 16 hours
Standby time: 250 hours
Note
•YoucaninstallaDSL(digitalsubscriberline)lterto
prevent noise and caller ID problems caused by the
DSL interference.
•YoucanndtheDeclarationofConformityon
www.p4c.philips.com.
Frequently asked questions
No signal bar is displayed on the screen.
•The handset is out of range. Move it closer to the
base station.
•If the handset displays
[Register your handsets], put the handset on
the base until the signal bar appears.
If I fail to pair (register) the additional handsets to
the base station, what do I do?
Your base memory is full. Access > [Services]
> [Unregister] to unregister the unused handsets
and try again.
I have chosen a wrong language which I cannot
read, what do I do?
1 Press to go back to the standby screen.
2 Press to access the main menu screen.
3 The following options will appear on the screen:
[Phone setup] > [Language]
[Réglages]> [Langue]
[Telefon-Setup] > [Sprache]
[Cong. telef.] > [Lingua]
4 Select them to access the language options.
5 Select your own language.
My handset is in searching status, what do I do?
•Make sure that the base station has power supply.
•Register the handset to the base station.
•Move the handset closer to the base station.
I cannot change the settings of my voice mail, what
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
No display
•Make sure the batteries are charged.
• Make sure there are power and phone connections.
The handset on the charger does not charge.
•Make sure the batteries are inserted correctly.
•Make sure the handset is placed properly on the
charger. The battery icon animates when charging.
•Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dirty. Disconnect the power
supplyrstandcleanthecontactswithadampcloth.
•Batteries are defective. Purchase new ones with
thesamespecications.
Bad audio (crackles, echo, etc.)
•The handset is nearly out of range. Move it closer
to the base station.
•The phone receives interference from the nearby
electrical appliances. Move the base station away
from them.
•The phone is at a location with thick walls. Move
the base away from them.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
•The service is not activated. Check with your
service provider.
•The caller’s information is withheld or unavailable.
www.philips.com/support
For information, refer to the extended user
documentation online.
When this crossed-out wheeled
bin symbol is attached to
a product it means that the product
is covered by the European Directive
2002/96/EC.
2013 © WOOX Innovations Limited.
All rights reserved.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used by WOOX Innovations Limited
under license from Koninklijke Philips N.V.
UMS_D400-405
05_EN_V2.0
WK13375
0168