Philips M3451B/38 User Manual
Displayed below is the user manual for M3451B/38 by Philips which is a product in the Telephones category. This manual has pages.
Related Manuals
M345
Register your product and get support at
www.philips.com/support
Short user manual
05.en
Important safety
instructions
Warning
• The Electrical network is classified as hazardous.
The only way to power down the charger is to
unplug the power supply from the electrical outlet.
Ensure that the electrical outlet is always easily
accessible.
• Refer to safety information before using the
product.
• This product complies with European R&TTE
directive 1999/5/EC.
• Use only the power supply listed in the user
instructions.
• Use only the batteries listed in the user instructions.
• Do not allow the product to come into contact
with liquids.
• Risk of explosion if battery is replaced by an
incorrect type.
• Dispose of used batteries according to the
instructions.
• When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.
Display icons
It displays the connection between the handset
and the base. The more bars are shown, the
better the signal strength is.
It remains steadily on when browsing incoming
calls in the call log.
It indicates an outgoing call in the redial list.
It ashes when there is a new missed call or
when browsing new missed calls. It remains
steadily on when browsing the missed calls in
call log that are already read.
It ashes when receiving incoming call. It remains
steadily on during a call.
The speaker is on.
The ringer is off.
The alarm is activated.
Answering machine: it ashes when there is
a new message or when the memory is full.
It remains steadily on when the telephone
answering machine is turned on.
Voice messages indicator: ashes for new
messages, is steady for reviewed messages.
* This is network dependent
It is displayed when you scroll up/down a list or
increase and decrease the volume.
There are more digits on the right. Press to
read.
ECO+
The ECO+ mode is activated.
1Overview
In call
Phonebook
Access the redial list.
Adjust the volume.
Recall (network dependent).
End calls.
Enter a pause (press and hold).
Turn the speaker on/off.
Mute/unmute the microphone.
In menu
Conrm / Select / Enter the option menu.
Cancel / back
Up / down
Exit menu.
Standby
Access the main menu.
Access the redial list. / Switch the ambient
light on/off (press and hold).
Phonebook
Call log
Make and receive calls.
Switch the handset on/off (press and hold).
Make intercom call (press and hold).
Lock/unlock the keypad (press and hold).
Make and receive calls through the speaker.
Listen to new message from the answer
machine. / Access the answer machine menu.
In text input
Delete text.
Enter a space.
Switch upper/lower case (press and hold).
Light ring
Standby White / blue / purple
Incoming call Flashing green
On a call Green
Notications (missed
calls, new voice mails, new
incoming messages etc.)
Flashing red
Alarm Flashing amber
Find handset
Light ring
Microphone
Earpiece
Loudspeaker
(back side)
Display icons
2Connect
Multi-handset version only.
1 2 3
3Get started
Congure your phone Charge your phone
Charge 8 hours
1 The batteries are pre-installed in the handset. Pull
the battery tape off from the battery door before
charging.
2 When using your phone for the rst time, you see
a welcome message (country dependent).
3 Set the country and language if prompted.
4 Set the date and time.
• If the time is in 12-hour format, press /
to select [am] or [pm] (country dependent).
> 70%
40% - 70%
10% - 40%
Flashing: low battery
Phonebook
Add record
1 Press .
2 Select [Phonebook] > [Add new].
3 Follow on-screen instructions.
Call from the phonebook
1 Press .
2 Select a record and press .
Direct access memory
You have 2 direct access memories (Keys 1 and 2).
To dial the saved phone number automatically, press
and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to the voice mail number and information
service number of your service provider respectively.
(network dependent).
Call log
Call from the call log
1 Press .
2 Select a record and press .
View record
Press > > [View].
Save record
1 Press > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > [Delete].
2 Follow on-screen instructions.
Redial list
Call from the redial list
1 Press .
2 Select a record and press .
Save record
1 Press > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > [Delete].
2 Follow on-screen instructions.
Telephone answering machine
(for M345 only)
Turn the answering machine on or off
1 Press > [Answ. Machine] > [On/off].
2 Follow on-screen instructions.
Listen to the incoming messages
Press > [Answ. Machine] > [Play].
Delete an incoming messages
1 When you listen to the message, press to
enter the options menu.
2 Select [Delete], then press to conrm.
Register additional handsets
You can register additional handsets to the base
station.
1 Press .
2 Select [Services] > [Register], then press
to conrm.
3 Press and hold on the base station for
10 seconds.
4 Enter the system PIN/passcode (0000).
5 Press to conrm the PIN/passcode.
» Registration is complete in less than 2 minutes.
Restore default settings
You can reset your phone settings to the original
factory settings.
1 Press .
2 Select [Services] > [Reset], then press to
conrm.
3 Follow on-screen instructions.
Note
• You may recall the original PIN/passcode by
following this procedure.
4Enjoy
Technical data
Battery
• Philips: 2 x AAA NiMH 1.2 V Rechargeable
550 mAh batteries
Use only the supplied batteries.
Adapter (base and charger)
Input: Output:
MEIC:
MN-A102-U130
100-240 V~
50/60 Hz 200 mA
6 Vdc
400 mA
Tenpao:
S003IB0600040
P/N: R017886V-B
100-240 V~
50/60 Hz 150 mA
6 Vdc
400 mA
Phonebook with 50 entries
Call log with 20 entries
Talk time: 16 hours
Standby time: 180 hours
Note
• You can nd the Declaration of Conformity on
www.p4c.philips.com.
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the
base station.
• If the handset displays [Unregistered], register
your handset (see the section on “Register
additional handsets”).
If I fail to pair (register) the additional handsets to
the base station, what do I do?
Your base memory is full. Access > [Services]
> [Unregister] to unregister the unused handsets
and try again.
My handset is in searching or unavailable status,
what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I have chosen a wrong language which I cannot
read, what do I do?
1 Press to go back to the standby screen.
2 Press to access the main menu screen.
3 The following options will appear on the screen:
[Phone setup] > [Language]
[Réglages] > [Langue]
[Telefon-Setup] > [Sprache]
[Cong. telef.] > [Lingua]
4 Select them to access the language options.
5 Select your own language.
I have chosen a wrong country in Welcome screen,
what do I do?
Reset your phone settings to the original factory
settings (see the section on “Restore default
settings”).
I cannot change the settings of my voice mail, what
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
The handset on the charger does not charge or the
battery discharges too fast.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger. If the docking tone is turned on, you can
hear the docking tone when you place the handset
on the charging cradle.
• The charging contacts are dirty. Disconnect the
power supply rst and clean the contacts with a
damp cloth.
• The battery is not fully recharged. Leave the
handset on the charging cradle for at least 8 hours
or until the battery icon on the handset stops
scrolling and indicates full bar.
• The batteries are old or defective. Purchase and
replace with new rechargeable batteries with the
same specications.
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away
from them.
• The phone is at a location with thick walls. Move
the base away from them.
• The phone receives interference from the DSL
(digital subscriber line) connection. Install a DSL
lter to prevent the noise. Contact your service
provider for the DSL lter.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or unavailable.
Frequently asked questions
www.philips.com/support
To access the user instructions online, use the
reference model number written on the product
label at the bottom of the base station.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This product has been manufactured by, and
is sold under the responsibility of Gibson
Innovations Ltd., and Gibson Innovations Ltd. is
the warrantor in relation to this product.
Philips and the Philips Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used under license from Koninklijke
Philips N.V.
UMS_M345
05_EN_V1.0
WK15512
0168