Philips M7701B/23 User Manual
Displayed below is the user manual for M7701B/23 by Philips which is a product in the Telephones category. This manual has pages.
Related Manuals
Register your product and get support at
www.philips.com/support
Short
user
manual
Design cordless
phone (M770)
Design cordless
phone with
answering machine
(M775)
Faro
Important safety instructions
Warning
• The Electrical network is classified as hazardous.
The only way to power down the charger is to
unplug the power supply from the electrical outlet.
Ensure that the electrical outlet is always easily
accessible.
• Refer to safety information before using the
product.
• Hereby, Gibson Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions of
Directive 2014/53/EU.
• Use only the power supply listed in the user
instructions.
• Use only the batteries listed in the user instructions.
• Do not allow the product to come into contact with
liquids.
• Risk of explosion if battery is replaced by an
incorrect type.
• Dispose of used batteries according to the
instructions.
• When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.
In call
Enter the option menu.
Change the sound prole.
/ Adjust the volume.
Recall (network dependent).
End calls.
Enter a pause (press and hold).
Turn the speaker on/o.
/ Mute/unmute the microphone.
Standby
Access the main menu (press and hold
when there is a new event).
Access the redial list.
Phonebook
Call log
Make and receive calls.
Access the network voice mail (network
and country dependent) (press and hold).
Switch the handset on or o (press and
hold).
Make intercom call (press and hold).
Lock/unlock the keypad (press and hold).
Make and receive calls through the
speaker.
/ M775 only: Press to play new message from
the answer machine. / Access to the answer
machine menu.
In menu
Conrm / Select / Enter the option menu.
Cancel / back
/ Up / down
Exit menu.
In text input
Delete text.
Enter a space.
/ Left / Right
Switch upper/lower case (press and hold).
Display icons
It shows the connection status between the
handset and base station. The more bars are
shown, the better the signal strength is.
It remains steadily on when browsing incoming
calls in the call log.
It remains steadily on when browsing outgoing
call in the redial list.
It ashes when there is a new missed call or
when browsing unread missed calls in call log.
It remains steadily on when browsing the read
missed calls in call log.
It remains steadily on when browsing blocked
calls in call log.
It ashes when receiving incoming call. It
remains steadily on when you are in a call.
The speaker is on.
The ringer is o.
The silent mode is set and within active period
(the phone does not ring).
M775 only: Answering machine: it ashes when
there is a new message or when the memory
is full. It is displayed when the telephone
answering machine is turned on.
Voice messages indicator: ashes for new
messages, is steady for reviewed messages.
* This is network dependent.
The silent mode is set, but is outside of active
period.
/
The alarm is activated. The icon is displayed on
the screen of the pre-registered handset and
base station.
It is displayed when you adjust the volume.
The Eco mode is activated.
The ECO+ mode is activated.
It enables the phone to couple with the
hearing aid device to amplify the sound and
reduce noise interference.
1Overview
Microphone
Loudspeaker
Earpiece
(M775)
(M770)
Display icons
LCD display
Find handset /
registration
(bottom)
LED indicator
Make and receive calls through the
speaker (when the pre-registered
handset is on the base station).
Snooze the
alarm.
2Connect
12
3Get started
Congure your phone Charge your phone Remove and install the battery
sleeve
(when necessary)
Charge 8 hours
Charge your handset by docking
it in either direction.
1 The batteries are pre-installed in the handset.
Pull the battery tape o from the battery door
before charging.
2 When using your phone for the rst time, you
see a welcome message (country dependent).
3 Set the country and language if prompted.
4 Set the date and time.
• If the time is in 12-hour format, press
/ to select [am] or [pm] (country
dependent).
> 70%
40% - 70%
10% - 40%
Flashing: low battery
Scrolling: charging in progress
1
2
4Enjoy
Phonebook
Add record
1 Press [Menu] > [Phonebook] > [Add new].
2 Follow on-screen instructions.
Call from the phonebook
1 Press .
2 Select a record and press .
Call from the direct access memory
Press and hold on the keys in standby mode. The
availaibility of direct access memory is country
dependent.
Call log
Call from the call log
1 Press .
2 Select a record and press .
Save record
1 Press > [Option] > [Save number].
2 Follow on-screen instructions.
Redial list
Call from the redial list
1 Press [Redial].
2 Select a record and press .
Save record
1 Press [Redial].
2 Select a record and select [OK] > [Option] >
[Save number]
3 Follow on-screen instructions.
Telephone answering
machine (for M775 only)
Turn the answering machine on or o
1 Press [Menu] > [Answer machine] > [On/o].
2 Follow on-screen instructions.
• [On] > [Answer only] means the answering
machine is on. Calls are only answered,
messages are not recorded.
• [On] > [Answer & rec.] means the answering
machine is on. Calls are answered and
messages are recorded.
Listen to the incoming messages
Press [Menu] > [Answer machine] > [Play].
Register the handset or
additional handsets
You can register additional handsets to the base
station.
1 Press [Menu] on the handset.
2 Select [Services] > [Register], then press
[OK] to conrm.
3 Press and hold on the base station for
10 seconds.
4 Enter the system PIN/passcode (0000).
5 Press [OK] to conrm the PIN/passcode.
» Registration is complete in less than
2 minutes.
Note
The handset and the base station are GAP
compliant, which means they guarantee the
minimum functions: register a handset, take
the line, make a call and receive a call. The
advanced features may not be available if
you use them with other makes. To register
the handset to another GAP-compliant base
station, follow the registration procedure of
that base station.
Restore default settings
You can reset your phone settings to the original
factory settings, and recall the original PIN/
passcode.
1 Press [Menu].
2 Select [Services] > [Reset], then press [OK] to
conrm.
3 Follow on-screen instructions.
5Learn more
Silent mode
Sets time during which the phone will not ring.
[Privacy mode] > [Silent mode]
MySound
Customizes the sound of voices to your liking.
[Sounds] > [MySound]
Eco/ECO+ mode
Reduces transmission power and radiation (causes
2 seconds ring delay, 50% shorter standby time).
[Phone setup] > [Eco mode]/[ECO+ mode]
Call barring
Prevents unwanted outgoing calls to selected
numbers.
[Privacy mode] > [Call barring]
Block incoming calls
Blocks incoming calls to certain undesirable
numbers.
[Privacy mode] > [Call block]
Technical
data
Battery
• Philips: 2 x AAA NiMH 1.2 V Rechargeable
550 mAh batteries
Use only the supplied batteries.
Adapter (base and charger)
Tenpao: S003GB0600050
Input: 100-240 V~ 50/60 Hz 150 mA
Output: 6 Vdc 500 mA
Phonebook with 100 entries
Call log with 50 entries
Talk time: 16 hours
Standby time: 250 hours
RF output power: < 24 dBm
Frequency band: 1880 MHz ~ 1900 MHz
Note
You can nd the Declaration of Conformity on
www.p4c.philips.com.
Frequently asked questions
My handset displays [Searching] or
[Unavailable], or [Register your Handset],
what do I do?
• Make sure that the base station has power
supply.
• The handset is out of range. Move it closer to the
base station.
• The handset is not paired with the base. Register
the handset to the base station.
If I fail to pair (register) the additional
handsets to the base station, what do I do?
• Your base memory is full. Access >
[Services] > [Unregister] to unregister the
unused handsets and try again.
• If registration fails, unplug the power adapter
from the base station and plug it back. Wait for
15 seconds, and then repeat the registration
procedure.
I have chosen a wrong country in Welcome
screen, what do I do?
Reset your phone settings to the original factory
settings (see the section on “Restore default
settings”).
I have chosen a wrong language which I
cannot read, what do I do?
1 Press to go back to the standby screen.
2 Press to access the main menu screen.
3 The following options will appear on the screen:
[Phone setup] > [Language]
[Réglages] > [Langue]
[Telefon-Setup] > [Sprache]
[Cong. telef.] > [Lingua]
4 Select them to access the language options.
5 Select your own language.
The handset loses connection with the
base or the sound interrupts during a call.
• The handset is nearly out of range. Move it closer
to the base station.
• Check if the ECO mode is activated. Turn it o
to increase the handset range and enjoy the
optimal call conditions.
• Re-register the handset to the base station.
The handset on the charger does not
charge or the battery discharges too fast.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger. If the docking tone is turned on, you
can hear the docking tone when you place the
handset on the charging cradle. The battery icon
animates when charging.
• The charging contacts are dirty. Disconnect the
power supply rst and clean the contacts with a
damp cloth.
• The battery is not fully recharged. Leave the
handset on the charging cradle for at least
8 hours or until the battery icon on the handset
stops scrolling and indicates full bar.
• The batteries are old or defective. Purchase and
replace with new rechargeable batteries with the
same specications.
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station
away from them.
• The phone is at a location with thick walls. Move
the base away from them.
• The phone receives interference from the DSL
(digital subscriber line) connection. Install a DSL
lter to prevent the noise. Contact your service
provider for the DSL lter.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or
unavailable.
www.philips.com/support
To access the user instructions online, use the
reference model number written on the product
label at the bottom of the base station.
This symbol on a product means that the product is
covered by European Directive 2012/19/EU.
This product has been manufactured by, and is sold under
the responsibility of Gibson Innovations Ltd., and Gibson
Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used under
license from Koninklijke Philips N.V.
UMS_M770/775
05_EN_V1.0
WK16254