Table of Contents
Philips ORD7100R/00 User Manual
Displayed below is the user manual for ORD7100R/00 by Philips which is a product in the Radios category. This manual has pages.
Related Manuals
www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
ORD7100
Question?
Contact
Philips
1EN
Contents
1 Safety 2
2 Your docking system 3
Introduction 3
What's in the box 3
Overview of the system 4
3 Connect the FM antenna and
power cord 5
4 Power on and select a source 6
5 Set the clock 6
6 Use the dock 7
Compatible iPod/iPhone models 7
Enjoy audio through the dock 7
Charge your iPod/iPhone 8
Undock your iPod/iPhone 8
7 Listen to FM radio 8
Search for a radio station automatically 8
Search for a radio station manually 8
Store radio stations automatically 9
Store radio stations manually 9
8 Listen to an external device 9
9 Adjust the volume 10
10 Use the remote control 10
Activate the battery 10
Control play 10
Replace the battery 11
11 Troubleshooting 12
12 Product information 13
Amplier 13
FM Tuner 13
Speakers 13
General information 13
13 Notice 14
Compliance 14
Care of the environment 14
Trademark notice 14
Copyright 15
Contents
2EN
1 Safety
Read and understand all instructions before you
use this product. If damage is caused by failure
to follow the instructions, the warranty does
not apply.
Risk of electric shock or re!
• Never remove the casing of the product.
• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Philips Consumer
Care to have the product checked before
use.
• Never place the product and accessories
nearnakedamesorotherheatsources,
including direct sunlight.
• Never insert objects into the ventilation
slots or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord,
hold the plug securely, never the cable.
• Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heatsuchassunshine,reorthelike.
Risk of short circuit or re!
• Before you connect the product to the
power outlet, make sure that the power
voltage matches the value printed on the
back of the product. Never connect the
product to the power outlet if the voltage
is different.
• Never expose the remote control or
batteries to rain, water, sunshine, or
excessive heat.
• Avoid force coming onto power plugs.
Loosepowerplugscancausearcingorre.
• Correctly install the battery with its
polarity (+/- signs) as marked on the
remote control.
• Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
Risk of injury or damage to the product!
• This product shall not be exposed to
dripping or splashing!
• Do not place any sources of danger on this
product(e.g.liquidlledobjects,lighted
candles).
• Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
Risk of overheating!
• Neverinstallthisproductinaconned
space. Always leave a space of at least four
inches around the product for ventilation.
• Make sure that curtains or other objects
never cover the ventilation slots on the
product.
Risk of contamination!
• Remove the battery if it is exhausted or if
the remote control is not to be used for
an extended period of time.
• Batteries contain chemical substances, they
should be disposed of properly.
Risk of swallowing coin battery!
• The device may contain a coin/button
type battery, which can potentially be
swallowed. Keep the battery out of reach
of children at all times! If swallowed, the
battery can cause serious injury or death.
Severe internal burns can occur within two
hours of ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
3EN
• When you change the batteries, always
keep all new and used batteries out of
reach of children. Make sure that the
battery compartment is completely secure
after you replace the battery.
• If the battery compartment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
Note
•The type plate is located on the back of the product.
2 Your docking
system
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this system, you can:
• enjoy audio from an iPod/iPhone or
external device,
• charge your iPod/iPhone, and
• listen to FM radio stations.
What's in the box
Check and identify the contents of the package:
a Docking speaker
b Remote control
c User manual
d VDE AC power cord
e AC power cord for the U.K.
f MP3 link cable
g FM antenna
def
ab
c
User Manual
ORD7100
g
4EN
Overview of the system
a SOURCE
• Turn to select a source.
• Turn to switch the system from
standby mode to normal mode.
b
• Press to switch the system between
standby mode and normal mode.
• Turn to adjust the volume.
c Dock for iPod/iPhone
d LCD screen
e
• In radio mode, turn to search for a
radio station manually.
a
b
c
g
h
f
e
d
i
• In radio mode, press and hold to
activate the automatic search for and
storage of radio stations.
• For a compatible iPod/iPhone, press to
pause or resume music play.
• For a compatible iPod/iPhone, press
and hold to switch it to sleep mode, or
press to wake it up.
f PRESET
• Turn to select a preset radio station.
g AC MAIN~
• Connect to the AC power cord.
5EN
h MP3-LINK
• Connect to an external player by an
MP3 link cable.
i Socket for FM antenna
• Connect to an FM antenna.
3 Connect the
FM antenna and
power cord
1 Connect the FM antenna to the product.
2 Connect the AC power cord to the AC
MAIN~ socket and then to the wall outlet.
6EN
4 Power on and
select a source
To power on the product,
• press the knob,
• turn the SOURCE knob on the product, or
• press on the remote control.
» The product switches to the last
selected source.
• To switch the product to standby
mode, press the knob or again.
To select a source,
• turn the SOURCE knob on the product, or
• press the SRC button on the remote
control repeatedly.
• FM radio: is highlighted, and the
frequency of the current FM radio
station is displayed.
• iPod/iPhone: is highlighted, and
scrolls.
• External device: is highlighted, and
is displayed.
5 Set the clock
1 In standby mode, press and hold the
knob for two seconds.
» is displayed with 24 blinking.
2 Turn the knob to select a time format,
and then press the knobtoconrm.
• : 24-hour time format
• : 12-hour time format
» The hour digits blink.
3 Turn the knob to set the hour, and
then press the knobtoconrm.
» The minute digits blink.
4 Turn the knob to set the minute, and
then press the knobtoconrm.
» The set time is displayed.
Tip
•Once your iPod/iPhone is connected and recognized,
the clock on the product is synchronized with the
iPod/iPhone.
7EN
6 Use the dock
You can enjoy audio from a compatible iPod/
iPhone through this product.
An application Philips HomeStudio is available
on Apple App Store for this product. To enjoy
full features, download and install the application
to your iPod/iPhone.
Note
•During play, no audio signals are transferred through
the headphone socket of your iPod/iPhone.
•Once your iPod/iPhone is connected and recognized,
the product synchronizes its clock with the iPod/iPhone
automatically.
Compatible iPod/iPhone
models
This product supports the following iPod and
iPhone models.
Made for
• iPod touch (2nd, 3rd, and 4th generation)
• iPod classic
• iPod nano (2nd, 3rd, 4th, 5th, and 6th
generation)
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPhone 3G
Enjoy audio through the dock
1 Switch the source to .
2 Push the dock tray to eject it.
3 Connect your iPod/iPhone to the dock.
4 Play a track on your iPod/iPhone.
• To start, pause. or resume play, press
the knob.
• To skip to a track, turn the knob.
• To switch the iPod/iPhone to sleep
mode or wake it up, press and hold
the knob.
8EN
Charge your iPod/iPhone
Once the iPod/iPhone is docked and
recognized, the charging starts.
Undock your iPod/iPhone
Note
•Risk of damage to the dock or your iPod/iPhone: Do
not twist or shake your iPod/iPhone.
1 Disconnect the iPod/iPhone from the dock.
2 Push the dock tray inwards until you hear a
"click" to store it.
7 Listen to FM
radio
Note
•For optimal reception, fully extend the antenna and
adjust its position, or connect an outdoor antenna.
•This system does not support MW (medium wave)
radio reception.
•You can store up to 20 stations for each band.
Search for a radio station
automatically
Turn the knob clockwise or anti-clockwise,
and then press the knob in two seconds.
» is displayed, and then the radio
frequency changes until a strong
station is detected.
• To stop the search, press the knob
again.
Search for a radio station
manually
Turn the knob until the frequency of target
radio station is displayed.
9EN
Store radio stations
automatically
Press and hold the knob until is
displayed.
» Afterthesearchiscomplete,therst
stored radio station is broadcast.
• To tune to a stored radio station, turn the
PRESET knob until its sequence number is
displayed.
Store radio stations manually
1 Tune to the target radio station.
2 After two seconds, press the knob.
» PXX is displayed with XX blinking (XX
indicates the sequence number).
3 Turn the PRESET knob to select a
sequence number.
4 Press the knobtoconrm.
5 Repeat steps 1-4 to store more radio
stations.
• To overwrite a preset radio station,
store another station with its sequence
number.
• To tune to a stored radio station, turn the
PRESET knob until its sequence number is
displayed.
8 Listen to an
external device
You can also listen to an external audio device,
for example, MP3 player, through this product.
1 Switch the source to .
2 Connect the MP3 link cable between
• the MP3-LINK socket on the back
panel of this product, and
• the headphone jack on the external
device.
3 Play audio on the external device (refer to
its user manual).
10 EN
9 Adjust the
volume
Turn the knob.
10 Use the remote
control
During use, you can use the remote control to
control play.
Activate the battery
Forthersttimeuse,pulltheprotectivetab
out from the battery compartment.
Control play
During play, follow the instructions below to
control play.
FM mode
Buttons Functions
/ Totunetoaspecicradio
station, press repeatedly until its
frequency is displayed.
/ To tune to the previous or next
strong radio station, press and
hold to start scanning.
PRESET +/- To tune to a preset radio
station, press repeatedly until its
sequence number and frequency
are displayed.
PROG To program radio stations,
1 Tune to the radio station that
your want to store.
2 Press PROG to activate the
programming.
3 Press PRESET +/- to select a
sequence number.
4 Press PROGtoconrm.
5 Repeat the steps 1-4 to pro-
gram more radio stations.
DISP To display the clock or current
frequency, press it.
11EN
DOCK mode
Buttons Functions
To start, pause, or resume play,
press it.
To switch the iPod/iPhone to
sleep mode or wake it up, press
and hold it.
/ To skip to a track, press repeatedly.
/ To rewind a track or search
forward fast, press and hold.
MENU To select a track from the library,
1 Press MENU to access the
iPod/Music (iPod/Music) menu
of your iPod/iPhone.
2 Press MENU repeatedly to tog-
gle through the categories.
3 Press / to toggle
through sub-categories or
select a track.
4 Press to enter lower-level
menu or start the selected
track.
Volume
Buttons Functions
VOL+/
VOL-
To increase or decrease the volume,
press repeatedly.
MUTE To mute the product or release it
from mute status, press the button.
Replace the battery
1 Pull out the battery tray and then remove
theatbattery.
2 Insert one CR2025 battery with correct
polarity (+/-) as indicated.
3 Insert the battery tray.
12 EN
11 Troubleshooting
Warning
•Never remove the casing of this product.
To keep the warranty valid, never try to repair the product yourself.
If you encounter problems when using this product, check the following points before requesting
service. If the problem remains unsolved, go to the Philips Web page (www.philips.com/support). When
you contact Philips, make sure that the product is nearby and the model number and serial number are
available.
Problem Solution
No power Make sure that the AC power cord is connected properly.
Make sure that there is power at the AC power outlet.
If a connected iPod/iPhone stays inactive for 15 minutes when it is selected
as the source, the system switches to standby mode automatically.
No sound or poor sound Adjust the volume.
Press MUTE to release the speakers from mute status.
No response from the
product
Reconnect the AC power cord, and then turn on the product again.
If a connected iPod/iPhone stays inactive for 15 minutes when it is selected
as the source, the system switches to standby mode automatically.
Remote control does not
work
Before you press any function button, select the correct source with the
remote control instead of the system.
Reduce the distance between the remote control and the system.
Insert the battery with its polarity (+/– signs) aligned as indicated.
Replace the battery.
Aim the remote control at the iR sensor on the front panel of the system.
Poor radio reception Increase the distance between the product and other electrical appliances.
Fully extend the antenna.
Connect an outdoor FM antenna instead.
Clock is erased Power has been interrupted or the AC power cord has been
disconnected.
Reset the clock.
13EN
12 Product
information
Note
•Product information is subject to change without prior
notice.
Amplier
Frequency Response 60 Hz - 16 kHz,
±3 dB
Signal to Noise Ratio > 70 dBA
Aux Input 0.5 V RMS 10 kOhm
FM Tuner
Tuning Range 87.50 - 108.00 MHz
Tuning grid 50 kHz
Total Harmonic
Distortion
< 2%
Signal to Noise Ratio > 50 dBA
Number of preset
radio stations
20
Speakers
Speaker Impedance 6 Ohm
Speaker Driver 2 X 3" full range
Sensitivity > 82 dB/m/W
General information
AC Power Rating 100-240 V~, 50/60
Hz
Operation Power
Consumption
15 W
Dimensions (Main Unit) 325 x 175 x 167 mm
Weight (Main Unit) 3.5 kg
14 EN
13 Notice
Anychangesormodicationsmadetothis
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Compliance
This product complies with the radio
interference requirements of the European
Community.
Class II equipment symbol:
CLASS II apparatus with double insulation, and
no protective earth provided.
Care of the environment
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product is
covered by the European Directive 2002/96/EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Trademark notice
“Made for iPod” and “Made for iPhone”
mean that an electronic accessory has been
designedtoconnectspecicallytoiPodor
iPhonerespectively,andhasbeencertiedby
the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
15EN
the use of this accessory with iPod or iPhone
may affect wireless performance.
iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Copyright
2012 © Koninklijke Philips Electronics N.V.
Specicationsaresubjecttochangewithout
notice. Trademarks are the property of
Koninklijke Philips Electronics N.V or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
ORD7100_10_UM_V1.0