Table of Contents
Philips OST690/10 User Manual
Displayed below is the user manual for OST690/10 by Philips which is a product in the Home Audio Systems category. This manual has pages.
Related Manuals
www.philips.com/welcome
OST690
Always there to help you
User Manual
Question?
Contact
Philips
Register your product and get support at
2EN
Contents
1 Important 3
2 Your Speaker System 4
Introduction 4
What's in the box 4
Overview of the system 5
3 Get started 6
Connect power 6
Turn on 7
Turn off 7
Switch to standby mode 7
4 Play 8
Play from a USB device 8
Play from Bluetooth-enabled device 9
Play from an external audio device 9
5 Listen to FM radio 10
Tune to FM radio stations 10
Store radio stations automatically 10
Store radio stations manually 10
Select a preset radio station 10
6 Other features 11
Charge your mobile phone 11
Adjust display brightness 11
Adjust volume 11
Enhance bass 11
7 Product information 12
Specications 12
Supported MP3 disc formats 12
USB playability information 12
8 Troubleshooting 13
About Bluetooth device 14
9 Notice 14
3EN
1 Important
• Read these instructions.
• Follow all instructions.
• Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
• Do not install near any heat sources such
as radiators, heat registers, stoves, or
otherapparatus(includingampliers)that
produce heat.
• Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the unit.
• Only use attachments or accessories
speciedbythemanufacturer.
• Unplug this unit during lightning storms or
when unused for long periods of time.
• Referallservicingtoqualiedservice
personnel. Servicing is required when the
unit has been damaged in any way.
• Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
• Install all batteries correctly, + and - as
marked on the unit.
• Do not mix batteries (old and new or
carbonandalkaline,etc.).
• Remove batteries when the unit is not
used for a long time.
• Batteries (battery pack or batteries
installed)shallnotbeexposedtoexcessive
heatsuchassunshine,reorthelike.
• Tropical condition has been considered
and complied.
• The unit shall not be exposed to dripping
or splashing.
• Do not place any sources of danger on
theunit(e.g.liquidlledobjects,lighted
candles).
• Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Warning
•Never remove the casing of this unit.
•Never place this unit on other electrical equipment.
4EN
2 Your Speaker
System
Introduction
With this speaker system, you can:
• listen to FM radio;
• enjoy audio from Bluetooth-enabled
devices, USB device, and other external
audio devices; and
• charge your mobile phone with the
supplied USB cable.
The system offers you Dynamic Bass Boost
(DBB)toenrichsound.
What's in the box
Check and identify the contents of the package:
• Main unit
• AC power cord
• USB cable for charging
• Short user manual
• Safety¬iceleaet
5EN
Overview of the system
a Source selector
• Select a source: BLUETOOTH, FM, or
USB.
b LED indicator
c ON/OFF
• Turn the system on or off.
d
• Connect a USB storage device.
• Charge a mobile phone with the
supplied USB cable.
e AUDIO IN
• Connect an external audio device.
f Slider
• Stabilize the mobile phone while
charging.
g VOLUME
• Adjust volume.
h - TUNING +
• Tune to FM radio stations manually.
a
b
c
d
e
l
m
n
k
h
i
j
g
f
r
q
p
o
MODE PROG
SEARCH
-
PRESET
-
PROGPRESET +
SEARCH +
ALBALB
i DBB
• Turn dynamic bass enhancement on
or off.
j Display panel
k FM antenna
• Improve FM radio reception.
l ALB/PRESET -/+
• Select a preset radio station.
• Skip to the previous or next album.
• Adjust display brightness.
m MODE
• Selectarepeatorshufemode.
• Activate brightness adjustment.
n / SEARCH+/-
• Skip to the previous or next track.
• Tune to FM radio stations automatically.
• Search within a track.
o PROG
• Program the play sequence of tracks.
• Program FM radio stations.
6EN
p
• Open or close the compartment.
q
• Start or pause play.
r
• Stop play.
• Erase a program.
3 Get started
Always follow the instructions in this chapter in
sequence.
Connect power
The system can be powered by either AC
power or batteries.
Option 1: Battery power
Caution
•Batteries contain chemical substances, so they should
be disposed of properly.
Note
•Batteries are not supplied with the accessories.
1 Open the battery compartment.
2 Insert6batteries(type:R14/UM2/CCELL)
withcorrectpolarity(+/-)asindicated.
3 Close the battery compartment.
7EN
Option 2: AC power
Warning
•Risk of product damage! Make sure that the power
supply voltage corresponds to the voltage printed on
the back or the underside of the system.
•Risk of electric shock! When you disconnect the AC
power, always pull the plug from the socket. Never pull
the cord.
Connect the AC power cord to:
• the AC~ MAINS socket on the back of the
system.
• the wall outlet.
Tip
•To save energy, turn off the system after use.
Turn on
Switch the power slide to the ON position.
» The system switches to the last selected
source.
» The LED indicator lights up.
Turn off
Switch the power slide to the OFF position.
» The LED indicator turns off.
Switch to standby mode
• In AC power supply mode, if there is no
operation for 3 hours, this product will
switch to standby mode automatically for
energy-saving.Aftertherst30-minute
inactivity, the display will start to show the
remaining time before entering standby
mode(from149:59to0:00).
• In DC power supply mode, if there is no
operation for 15 minutes, this product
will switch to standby mode automatically
forenergy-saving.Aftertherst5-minute
inactivity, the display will start to show the
remaining time before entering standby
mode(from9:59to0:00).
» You may press to cancel the
countdown and resume normal operation,
or continue charging.
8EN
4 Play
Play from a USB device
Note
•Make sure that your USB device contains playable audio
content.
1 Rotate the source selector to the USB
position.
2 Press to open the compartment.
3 Insert the USB device into the socket
inside the compartment.
» Play starts automatically. If not, press
.
Note
•The USB socket is not compatible with music playback
from your smartphone.
Control play
In USB mode, you can control play through the
following operations.
/ Selectanaudiole;
Press and hold to fast-forward
or fast-reverse the track during
playback, then release to resume
play.
ALB-/
ALB+
Skip to the previous or next MP3/
WMA album.
Start or pause play.
Stop play.
MODE [ ]: Play the current track
repeatedly.
[ ]: Play the current album
repeatedly.
[ ]: Play all tracks repeatedly.
[ ]: Play tracks randomly.
To return to normal play, press
MODE repeatedly until the repeat
orshufeiconsdisappear.
Program tracks
In USB mode, you can program the play
sequence of tracks. A maximum of 20 tracks
can be programmed.
1 Press to stop playback.
2 Press PROG to activate the programming
mode.
» [PROG] is displayed and [P01] begins
to blink.
3 For MP3/WMA tracks, press ALB -/ALB +
to select an album.
4 Press / to select a track number,
then press PROGtoconrm.
5 Repeat steps 3-4 to program more tracks.
6 Press to play the programmed tracks.
» During play, [PROG] (program)is
displayed.
• To erase the program, press twice.
9EN
Play from Bluetooth-enabled
device
Note
•The effective operating range between the system and
thepaireddeviceisapproximately10meters(30feet).
•Any obstacle between the system and the device can
reduce the operational range.
•Compatibility with all Bluetooth devices is not
guaranteed.
1 Rotate the source selector to the
BLUETOOTH position.
2 On your Bluetooth device, enable
Bluetooth and search for Bluetooth devices
that can be paired (refer to the user
manualofthedevice).
3 When [OST690] is displayed on your
device, select it to start pairing and
connection.
» After successful pairing and connection,
the system beeps twice.
4 Play audio on your device.
» Audio streams from your device to this
system.
To disconnect the Bluetooth-enabled device:
• Deactivate Bluetooth on your device; or
• Move the device beyond the
communication range.
To clear Bluetooth pairing history:
Press and PROG together for 3 seconds.
» The current Bluetooth connection is
disconnected.
» After successful clearing, [CLR](clear)
blinks for 5 seconds, then [-] scrolls on the
display.
Play from an external audio
device
You can also listen to an external audio device
such as an MP3 player through this system.
1 Press to open the compartment.
2 Connect an audio cable (3.5mm, not
supplied)to:
• the AUDIO IN socket inside the
compartment.
• the headphone socket on an external
device.
» The system switches to Audio-in mode
automatically.
3 Play audio on the external device (see the
usermanualofthedevice).
10EN
5 Listen to FM
radio
Tune to FM radio stations
Note
•For better reception, fully extend and adjust the
position of the FM antenna.
1 Rotate the source selector to the FM
position.
2 Press SEARCH +/-.
» The system tunes to a station with
strong reception automatically.
3 Repeat step 2 to tune to more stations.
To tune to a radio station manually:
Rotate the tuning knob slowly.
Store radio stations
automatically
In tuner mode, press and hold PROG for 2
seconds.
» The system stores all the available FM radio
stations.
» Therststoredradiostationisbroadcast
automatically.
Store radio stations manually
Note
•You can store a maximum of 20 FM radio stations.
1 Tune to an FM radio station.
2 Press PROG to activate the storing mode.
3 Press PRESET + or PRESET - to allocate a
number(1to20)tothisradiostation,then
press PROGtoconrm.
» The preset number and the frequency
of the preset station are displayed.
4 Repeat the above steps to store other
stations.
Note
•To remove a pre-stored FM radio station, store another
station in its place.
Select a preset radio station
In FM tuner mode, press PRESET + or PRESET
- to select a preset radio station.
11 EN
6 Other features
Charge your mobile phone
Note
•Make sure that you have switched on the system.
1 Rotate the source selector to
BLUETOOTH/CHR or FM/CHR
2 Press to open the compartment.
3 Connect the supplied USB cable to:
• the socket inside the compartment.
• the USB socket on your mobile phone.
» The charging icon is displayed on your
phone.
4 Adjust the slider inside the compartment
to stabilize your phone.
BL
UETOOTH
/
CHR
USB
FM/CHR
BLUETOOTH
/CHR
US
B
FM/CHR
5 Close the compartment.
Note
•You cannot charge your mobile phone when the
system is powered by the batteries.
Adjust display brightness
1 Press and hold MODE for 3 seconds.
2 Press ALB/PRESET -/+ repeatedly to adjust
the display brightness.
Adjust volume
Rotate the VOLUME knob to adjust volume.
Enhance bass
To turn dynamic bass boost on or off, switch
the DBB slide to the ON or OFF position.
12EN
7 Product
information
Note
•Product information is subject to change without prior
notice.
Specications
Amplier
Max Output Power 6W per channel x 2
Frequency Response 125 -16000 Hz, -3dB
Signal to Noise Ratio >55 dBA
Total Harmonic
Distortion
<1 %
Audio-in Input 650 mV RMS
Tuner
Tuning Range 87.5 - 108 MHz
Tuning Grid 50 kHz
Sensitivity
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
<22 dBf
<41 dBf
Total Harmonic Distortion <3%
Signal to Noise Ratio >50 dBA
Bluetooth
Standard Bluetooth Standard Version 2.1+EDR
Range 10m(freespace)
Speaker
Speaker Impedance 8 ohm
Speaker Driver 4"
General
Power supply
- AC Power
- Battery
220-240 V~, 50/60 Hz;
6 x 1.5 V R14/UM2/C
CELL
Operation Power
Consumption
15 W
Standby Power
Consumption
<0.5 W
Max.Loading(USB) 5 V 1 A
Dimensions - Main Unit
(WxHxD)
447 x 230 x 116 mm
Weight(MainUnit) 2.2 kg
Supported MP3 disc formats
• ISO9660, Joliet
• Maximum title number: 512 (depending on
lenamelength)
• Maximum album number: 255
• Supported sampling frequencies: 32 kHz,
44.1kHz, 48 kHz
• SupportedBit-rates:32~256(kbps),
variable bit rates
USB playability information
Compatible USB devices:
• USBashmemory(USB2.0orUSB1.1)
• USBashplayers(USB2.0orUSB1.1)
• memory cards (requires an additional card
readertoworkwiththisapparatus)
Supported formats:
• USBormemoryleformatFAT12,FAT16,
FAT32(sectorsize:512bytes)
• MP3bitrate(datarate):32-320Kbpsand
variable bit rate
• WMA v9 or earlier
• Directory nesting up to a maximum of 8
levels
• Number of albums/ folders: maximum 99
• Number of tracks/titles: maximum 999
13 EN
• ID3 tag v2.0 or later
• File name in Unicode UTF8 (maximum
length:128bytes)
Unsupported formats:
• Empty albums: an empty album is an album
thatdoesnotcontainMP3/WMAles,and
is not be shown in the display.
• Unsupportedleformatsareskipped.For
example,Worddocuments(.doc)orMP3
leswithextension.dlfareignoredand
not played.
• AAC,WAV,PCMaudioles
• DRMprotectedWMAles(.wav,.m4a,
.m4p,.mp4,.aac)
• WMAlesinLosslessformat
8 Troubleshooting
Warning
•Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page
(www.philips.com/support).Whenyoucontact
Philips, make sure that the device is nearby
and the model number and serial number are
available.
No power
•Ensure that the AC power plug of the unit
is connected properly.
•Ensure that there is power at the AC
outlet.
•Insert the batteries with their polarities
(+/–signs)alignedasindicated.
•Replace the battery.
No sound or poor sound
•Adjust the volume.
No response from the unit
•Disconnect and reconnect the AC power
plug, then turn on the system again.
USB device not supported
•The USB device is incompatible with the
apparatus. Try another one.
Poor radio reception
•Increase the distance between the unit and
your TV or VCR.
•Fully extend the FM antenna.
14EN
About Bluetooth device
Music playback is unavailable on the system
even after successful Bluetooth connection.
•The device cannot be used with the
system to play music.
The audio quality is poor after connection
with a Bluetooth-enabled device.
•The Bluetooth reception is poor. Move
the device closer to the system or remove
any obstacle between the device and the
system.
Cannot connect with the system.
•Thedevicedoesnotsupporttheproles
required for the system.
•The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.
•The system is not in the pairing mode.
•The system is already connected with
another Bluetooth-enabled device.
Disconnect that device or all other
connected devices and then try again.
The paired device connects and disconnects
constantly.
•The Bluetooth reception is poor. Move
the device closer to the system or remove
any obstacle between the device and the
system.
•For some devices, the Bluetooth
connection may be deactivated
automatically as a power-saving feature.
This does not indicate any malfunction of
the system.
9 Notice
Anychangesormodicationsmadetothis
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
This product complies with the radio
interference requirements of the European
Community.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
15 EN
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separateintothreematerials:cardboard(box),
paperpulp(buffer)andpolyethylene(bags,
protectivefoamsheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Class II equipment symbol
This symbol indicates that the unit has a double
insulation system.
Note
•The type plate is located on the bottom of the
apparatus.
Specifications are subject to change without notice
2013 © WOOX Innovations Limited. All rights reserved.
This product was brought to the market by WOOX
Innovations Limited or one of its affiliates, further referred
to in this document as WOOX Innovations, and is the
manufacturer of the product. WOOX Innovations is the
warrantor in relation to the product with which this booklet
was packaged. Philips and the Philips Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
OST690_10_UM_V2.0