Philips PicoPix Micro+ PPX325 User Manual
Displayed below is the user manual for PicoPix Micro+ PPX325 by Philips which is a product in the Data Projectors category. This manual has pages.
Related Manuals
User Manual
Register your product and get support at
www.philips.com/support
Portable projector
Portable projector
PPX325
PicoPix Micro+
Introduction �������������������������������������������������3
Dear customer ...............................................................3
About this user manual ..............................................3
What’s in the box ..........................................................3
Customer service centre ............................................3
1 General safety information ��������������� 4
Setting up the product .............................................. 4
Repairs ............................................................................ 4
Power supply .................................................................5
2 Overview ������������������������������������������������5
Rear view .........................................................................5
Side view ......................................................................... 6
3 Connect ������������������������������������������������� 6
HDMI connection for image projection ............... 6
Connection for your smartphone........................... 7
Remote control............................................................... 8
4 Operation ���������������������������������������������� 8
Place the projector...................................................... 8
Connecting power supply ........................................ 8
Power on and setup ................................................... 8
Connecting to external speakers or
headphones .................................................................. 9
Placement options ...................................................... 9
5 Change settings �����������������������������������11
Language settings ....................................................... 11
Picture settings ............................................................. 11
Power control settings ............................................... 11
Restore default settings ........................................... 12
Other settings ..............................................................12
6 Service ��������������������������������������������������13
Built-in battery care ..................................................13
Cleaning ......................................................................... 13
Update software .........................................................13
Troubleshooting .......................................................... 14
7 Appendix ���������������������������������������������� 15
Technical data .............................................................15
CE statement ...............................................................16
FCC statement .............................................................16
Canada regulatory compliance .............................16
Other notice ..................................................................16
Table of contents
Introduction 3
Introduction
Dear customer
Thank you for purchasing this projector.
We hope you enjoy this product and the many
functions it offers!
About this user manual
The quick start guide supplied with this product
allows you to start using this product quickly
and easily. Detailed descriptions can be found
in the following sections of this user manual.
Read the entire user manual carefully. Follow
all safety instructions in order to ensure proper
operation of this product (see General safety
information, page 4). The manufacturer
accepts no liability if these instructions are not
followed.
Symbols used
Notice
Troubleshooting
This symbol indicates tips that will help
you in using this product more effectively
and easily.
DANGER!
Danger of personal injury!
This symbol gives warning of danger
of personal injury. Physical injury or
damage can result from improper
handling.
CAUTION!
Damage to the product or loss of data!
This symbol gives warning of damage
to the product and possible loss of
data. Damage can result from improper
handling.
What’s in the box
a PicoPix Micro projector (PPX325)
b USB cable
c Quick Start Guide
d HDMI to mini HMDI cable
e Remote control with 2 AAA batteries
1
2
4
3
ta
Quick Srt
Guide
Customer service centre
You can find the support hotline in the warranty
card or online:
Web: www.philips.com/support
Mail: philips.projector.eu@screeneo.com
International Phone: +41 215 391 665
Please ask your provider for international call
costs!
Access the electronic user manual at
https://support.screeneo.com
Access the community forum at
https://community.screeneo.com
Quick Start
Guide
ab
fc
d
e
Quick Start
Guide
ab
fc
d
e
5
4 Philips · PicoPix Micro+
1 General safety
information
Take note of all warning and safety notes
indicated. Do not make any changes or settings
that are not described in this user manual.
Incorrect operation, and improper handling can
lead to physical injury, damage to the product
or loss of data.
Setting up the product
This product is for indoor use only. Place the
product securely on a stable, flat surface.
To help avoid possible injuries to persons or
damage to the product itself, position all cables
in such a way that no one will trip over them.
Do not operate the product in damp rooms.
Never touch the mains cable or the mains
connection with wet hands.
The product must have sufficient ventilation
and must not be covered. Do not put the
product in closed cabinets, boxes, or other
enclosures when in use.
Protect the product from direct sunlight,
heat, intense temperature fluctuations and
moisture. Do not place the product in the
vicinity of heaters or air conditioners. Observe
the information on temperature listed in the
technical data (see Technical data, page 15).
Prolonged operation of the product causes the
surface to become hot. In case of overheating,
the product automatically switches to standby
mode.
Do not allow liquids to leak into the product.
Turn off the product and disconnect it from the
mains supply if liquids or foreign substances
leaked into the product. Have the product
inspected by an authorised service centre.
Always handle the product with care. Avoid
touching the lens. Never place heavy or sharp
objects on the product or on the power cable.
If the product gets too hot or emits smoke,
shut it down immediately and unplug the
power cable. Have your product checked by
an authorised service centre. Keep the product
away from open flames (e.g. candles).
The product has built-in battery. Do not
dissemble and modify. The built-in battery
should be replaced by qualified service staff
only.
Do not try to replace the built-in battery
yourself. Incorrect handling of the battery or
using the wrong type of battery can cause
damage to the product or cause injury.
DANGER!
Risk of explosion with incorrect type
of batteries!
There is a risk of explosion if the wrong
battery type is used.
Do not expose the batteries (battery pack or
embedded batteries) to excessive heat such as
sunshine, or open fire.
Under the following conditions, a layer of
moisture can appear inside the product which
can lead to malfunctions:
• if the product is moved from a cold to a
warm area;
• after a cold room is heated;
• when the product is placed in a damp
room.
Proceed as follows to avoid any moisture
buildup:
1 Seal the product in a plastic bag before
moving it to another room, in order for it to
adapt to room conditions.
2 Wait one to two hours before you take the
product out of the plastic bag.
The product should not be used in a very dusty
environment. Dust particles and other foreign
objects may damage the product.
Do not expose the product to extreme
vibrations. This may damage the internal
components.
Do not allow children to handle the product
without supervision. The packing materials
should be kept out of the hands of children.
For your own safety, do not use the product
during thunderstorms with lightning.
Repairs
Do not repair the product yourself. Improper
maintenance can result in injuries or damage to
the product. The product must be repaired by
an authorised service centre.
Please find the details of authorised service
centres on the warranty card supplied with this
product.
Do not remove the type label from this product,
as this will void the warranty.
Overview 5
Power supply
Use only a certified power adapter. Check
whether the mains voltage of the power supply
matches the mains voltage available at the
setup location. This product complies with the
voltage type specified on the product.
The power outlet shall be installed near the
product and shall be easily accessible.
The capacity of the built-in battery diminishes
with time. If the product functions only with
external power supply, the built-in battery is
defective. Contact an authorised service centre
to replace the built-in battery.
CAUTION!
Always use the button to turn the
projector off.
Turn off the product and unplug from the
power outlet before cleaning the surface
(see Cleaning, page 13). Use a soft, lint-
free cloth. Never use liquid, gaseous or easily
flammable cleaners (sprays, abrasives, polishes,
alcohol). Do not allow any moisture to reach
the interior of the product.
DANGER!
Risk of eye irritation!
This product is equipped with a high
power LED (Light Emitting Diode),
which emits very bright light. Do not
look directly into the projector lens
during operation. This could cause eye
irritation or damage.
2 Overview
Rear view
USB HDMI
h fg
cba d e
a Reset key
Reset the projector to the factory default
settings (use a small pin to press the reset
key).
b IR sensor
c Micro USB port
Connect to the power supply.
d
3.5 mm audio output; connect to external
speakers or headphones.
e Mini HDMI port
Connect to the HDMI output on a playback
device.
f
• Press and hold three seconds to switch
the projector on or off.
• Access the settings menu.
• Confirm a selection or entry.
• When the projector is switched on, the
LED turns blue. When the projector is
switched off, the LED turns off.
• When charging the projector, the LED
turns red regardless of the projector
switching on or off.
g /
• Navigate menu options.
• Increase or decrease volume.
h
Return to a previous menu screen.
6 Philips · PicoPix Micro+
Side view
a
a Focus adjustment knob
Adjust image sharpness.
3 Connect
Notice
You need to connect the projector to
an HDMI device, so that the projection
screen can show images.
Make sure all devices are disconnected
from the power outlet before establishing
or changing any connections.
Connection for your
smartphone
iPhone or iPad with Lightning Port:
Use the Official Lightning Digital AV Adapter
• Option 1: an HDMI to mini HDMI cable
from the Apple adapter to the projector.
• Option 2: an normal HDMI cable to the
HDMI to Mini HDMI adapter (included in
the box).
• Option 3: Google Chromecast dongle
connected directly to the projector, the
iPhone will then cast any content to the
projector.
HDMI connection for image
projection
Connect a playback device (e.g. a Blu-ray
player, gaming console, camcorder, digital
camera or PC) to the projector through HDMI
connection. With this connection, images are
shown on the projection screen, and audio is
played on the projector.
• Using an HDMI cable, connect the HDMI
connector (mini HDMI port) on the projector
to the HDMI output on the playback device.
Use an HDMI mini plug adapter for HDMI
connection if necessary.
USB HDMI
1
2
3
Connect 7
Smartphones / iPad Pro / MacBook / Other
Laptop or Tablet with USB-C connector:
Check if your USB-C equipped device supports
HDMI (video) through USB-C as some
smartphones support only USB-C Charge.
• Option 1: connect a USB-C to HDMI cable
directly to the projector using the HDMI to
Mini HDMI adapter (included in the box)
• Option 2: connect a USB-C to mini HDMI
cable directly to the projector
• Option 3: connect a USB-C adapter to
your smartphone, then an HDMI to mini
HDMI cable to the projector
• Option 4: connect a USB-C adapter to
your smartphone, then an HDMI cable and
use the HDMI to mini HDMI adapter to the
projector
• Option 5: use a dedicated Adapter (Like
Apple Digital AV Adapter) from the device
to the projector
• Option 6: Google Chromecast dongle
connected directly to the projector, your
device will then cast any content to the
projector
Smartphones with MHL connector:
Your smartphone may have a micro USB
connector with MHL technology (old
smartphones)
Be sure that your smartphone supports MHL
through the micro USB port as some lower end
smartphones support only micro USB Charge.
If your smartphone is compatible, you can
directly connect your smartphone to the
projector using a MHL adapter to an HDMI
cable.
DEVICEDEVICE
PROJECTORPROJECTOR
MHL adapter
Power
8 Philips · PicoPix Micro+
Remote control
OK
a
d
e
b
c
f
g
h
a
Access the settings menu.
b
Confirm a selection or entry.
c
Access the home menu.
d
Mute or restore volume.
e /
Increase or decrease volume.
f
Return to a previous menu screen.
g Navigation buttons
• Navigate menu options.
• Press / to change a selection.
h
• Press and hold for one second to switch
the projector on or off.
• When the projector is switched on, the
LED turns blue. When the projector is
switched off, the LED turns off.
• When charging the projector, the LED
turns red regardless of the projector
switching on or off.
4 Operation
Notice
You need to connect the projector to
an HDMI device, so that the projection
screen can show images (see Connect,
page 6).
Place the projector
Place the projector on a flat surface in front of
the projection surface.
You can also install the projector in different
configurations (see Placement options, page
10).
Connecting power supply
The projector can be operated by either
external power or built-in battery.
CAUTION!
Always use the button to turn the
projector on and off.
Operation by external power
1 Using the supplied USB cable, connect the
port on the projector to the USB port
on your computer or a power adapter (not
included).
a
b
Operation by built-in battery
The projector can be also operated on built-in
battery for portability.
Charging projector
Charge the projector for 1.5 hours before first
use.
Charge the projector when the low battery icon
appears in the center of the projection screen.
• To charge the projector, connect the
projector to an external power supply as
described in the section of “Operation by
external power”.
• When charging, the LED on the projector
turns red. When fully charged, the red LED
turns off.
Operation 9
Notice
The capacity of the built-in battery
diminishes with time. If the projector
functions only with external power
supply, the built-in battery is defective.
Contact an authorised service centre to
replace the built-in battery.
Power on and setup
1 Press and hold on the projector for
3 seconds to switch the projector on or off.
• When the projector is switched on, the
LED on the projector turns blue if the
projector is not being charged.
• When charging, the LED on the
projector turns red regardless of the
projector switching on and off.
Set up the language
1 When the projector is turned on, press
on the projector to access the settings
menu, then navigate to select Language,
and press OK.
2 Press / to select a language.
Changing screen size
The projection screen size (or size of images) is
determined by the distance between the lens
of the projector and the projection surface.
• You can also use the digital zoom to
reduce the screen size up to 50%. When
the projector is turned on, press on the
projector to access the settings menu, then
navigate to select Digital Zoom, and press
OK. Then press / to adjust image size.
• The projection image size is to up to 65’’.
• The projection distance is 80 cm to 200 cm.
Image sharpness adjustment
To adjust image focus, turn the focus
adjustment knob on the side of the projector.
10 Philips · PicoPix Micro+
Placement options
You can install the projector in the following
configurations. Follow the guidelines below for
different projector placement.
Notice
For overhead mounting on ceiling,
purchase a projector mount
recommended by an installation
professional and follow the instructions
that come with the mount.
Before mounting on the ceiling, make
sure the ceiling can support the weight
of the projector and mounting kit.
For ceiling installation, this product
must be securely attached to the ceiling
in accordance with the installation
instructions. An improper ceiling
installation may result in accident, injury
or damage.
Front table
1 Place the projector on a table in front of the
projection screen. This is the most common
way to position the projector for quick
setup and portability.
2 To adjust projection to the correct position,
when the projector is turned on, press on
the projector to access the settings menu,
then navigate to select Proj. Direc. - Front
proj., then press OK.
Front ceiling
1 Mount the projector on the ceiling with
upside up in front of the projection screen.
A projector mount is required to mount the
projector on ceiling.
Connecting to external
speakers or headphones
Connect external speakers or headphones to
the projector. With this connection, audio from
the projector is played through the external
speakers or headphones.
DANGER!
Danger of hearing damage!
Before connecting the headphones,
turn down the volume on the projector.
Do not use the projector over a longer
time at high volume – especially when
using headphones. This could lead to
hearing damage.
1 Using a 3.5 mm audio cable, connect the
connector on the projector to the analogue
audio input (3.5 mm jack, or red and white
jacks) on the external speakers. Or connect
the connector on the projector to
headphones.
• The speakers of the projector are
deactivated automatically when the
external speakers or headphones are
connected to the projector.
USB HDMI
2 When connecting to the headphones, press
/ to adjust the volume to a comfortable
level.
Change settings 11
2 To adjust projection to the correct position,
when the projector is turned on, press on
the projector to access the settings menu,
then navigate to select Proj. Direc. - Rev.
front proj., then press OK.
Rear table
1 Place the projector on a table behind the
projection screen. A special rear projection
screen is required.
2 To adjust projection to the correct position,
when the projector is turned on, press on
the projector to access the settings menu,
then navigate to select Proj. Direc. - Rear
proj., then press OK.
Rear ceiling
1 Mount the projector on ceiling with upside
up behind the projection screen. To mount
the projector on ceiling behind the screen,
a projector mount and a special rear
projection screen is required.
2 To adjust projection to the correct position,
when the projector is turned on, press on
the projector to access the settings menu,
then navigate to select Proj. Direc. - Rev.
rear proj., then press OK.
5 Change settings
This section helps you change the settings of
the projector.
1 When the projector is turned on, press
on the projector to access settings menu.
2 Press / to navigate menu options, then
press on the projector to confirm the
settings.
Language settings
Select your desired language for on-screen
menu.
• Navigate to Language, and press OK, then
press / to select a language.
Picture settings
• Picture Preset: Select a predefined color
brightness setting for picture and video
display.
• Picture Adj.: Adjust Brightness/Contrast/
Saturation/Toneburst/Sharpness with the
values from 0 to 100.
12 Philips · PicoPix Micro+
Restore default settings
If the projector does not function normally,
reset the projector to the default settings. It will
delete all the current settings.
• Navigate to Full Reset, and press OK, then
follow on-screen instructions to complete
resetting.
Other settings
• Position: Re-position the settings menu on
the projection screen when it appears.
• Volume: Adjust volume of the projector.
• SW Version: Display the current software
version of the projector.
• HW Version: Display the current hardware
version of the projector.
• Soft. Update: Upgrade system software
via a USB device (see Update software,
page 13).
• Color Temp.: Set to Warm to enhance hotter
colors such as red; set to Cool to make
picture bluish; set to User to customize
color values in RGB mode.
• Proj. Direc.: Adjust the projection to
the correct position based on different
installation of the projector.
• Digital Zoom: Scale the projection image
within the range from 50% to 100%.
Power control settings
Go to the following menu options to control
power consumption.
• Sleep Timer: Select a time option which
enables the projector to automatically turn
off at a specified period of time.
• ECO Mode: Activate or deactivate energy
saving mode. If On is selected, energy
saving mode is activated when low battery
power occurs.
• Display Duration: Select a timer to
automatically turn the screen off when the
projector is idle.
Service 13
6 Service
Built-in battery care
The capacity of the built-in battery diminishes
with time. You can prolong the life of the
battery if you observe the following points:
• Without a power supply, the projector
operates on the built-in battery. When the
battery does not have sufficient power, the
projector turns off. In this case connect the
projector to the power supply.
• Charge the battery regularly. Don’t store
the projector with a completely discharged
battery.
• If the projector is not used for several
weeks, discharge the battery a little by
using the projector before storing it.
• Keep the projector and the battery away
from sources of heat.
• If the projector cannot be charged after
connecting to the power supply, use a small
pin to press the reset key (a small hole)
located near the USB port of the projector.
Note about deep discharge of battery
When the built-in battery is in deep discharge,
it may take longer for the actual charging
process to start. In this case, charge the
projector for at least five hours before using it.
DANGER!
Risk of explosion with incorrect type
of batteries!
Do not try to replace the built-in
battery yourself.
Cleaning
DANGER!
Instructions for cleaning!
Use a soft, lint-free cloth. Never use
liquid or easily flammable cleansers
(sprays, abrasives, polishes, alcohol,
etc.). Do not allow any moisture to
reach the interior of the projector.
Do not spray the projector with any
cleaning fluids.
Wipe over the surfaces gently. Be
careful that you do not scratch the
surfaces.
Cleaning the lens
Use a soft brush or lens cleaning paper for
cleaning the lens of the projector.
DANGER!
Do not use any liquid cleaning agents!
Do not use any liquid cleaning
agents for cleaning the lens, to avoid
damaging the coating film on the lens.
Update software
The latest software of the projector can be
found on www.philips.com/support for you
to get the best features and support from the
projector.
Before you update the software of the
projector, check the current software version:
• When the projector is turned on, press
on the projector to access the
settings menu then navigate to SW
Version.
CAUTION!
Do not turn off the projector or remove
the USB flash drive during the update.
Update software through USB
1 Check the latest software version on www.
philips.com/support. Find your product
(model number: PPX325), and locate
‘Software and drivers’.
2 Download the software into the USB flash
drive. Unzip the downloaded software file
and save it in the root directory of the USB
flash drive.
• After unzipping, copy that file to the
USB flash drive.
3 Connect the USB flash drive to the USB port
on the projector.
• Recommend to use an external power
when connecting a USB flash drive.
4 Turn on the projector with external power.
Press to access settings menu, and
navigate to select Soft. Update, then press
to start update process.
5 Follow the on-screen instructions to
complete the update.
14 Philips · PicoPix Micro+
Troubleshooting
Power cycling
If a problem occurs that cannot be corrected with the instructions in this user manual, follow the
steps given here.
1 Turn the projector off using .
2 Wait at least ten seconds.
3 Turn the projector on again using .
4 If the problem persists, please contact our technical service centre or your dealer.
Problems Solutions
The projector cannot be turned on. • Disconnect and reconnect the power cable, and try to
turn the projector on again.
• Low battery power. Connect the projector to an external
power supply.
The projection screen does not show images. • You need to connect the projector to an HDMI device or
USB-C device, so that the projection screen can show
images (see Connect, page 6).
• Check if the video output of the external device is
turned on.
The projector is charged slowly. • When powered on, the external power will be used first
to run the projector and unused power will charge the
battery.
• For faster charging, charge while the projector is
powered off.
The projector cannot be turned off. • Press and hold longer than ten seconds. If this does
not work, disconnect the power cable.
No image from the external HDMI device. • Disconnect the HDMI cable or switch off the HDMI
device.
• Wait three seconds.
• Reconnect the HDMI cable or switch on the HDMI
device again.
No sound from the external connected device. • Check the cables to the external device.
• Check that the sound is activated on the external
device.
• Only the original cables from the device manufacturer
may function.
No sound from external HDMI output device. • On the HDMI output device, set the audio setting to
Multichannel (Raw data) & Stereo (PCM).
No sound when you connect your computer via
HDMI cable.
• Check that the sound is activated on the computer.
The projector turns itself off. • Low battery power.
• When the projector is running for a long period of time,
the surface becomes hot.
• Check that the power cable is connected correctly.
The temperature of the projector’s surface is
warm.
• For this projector it is normal to generate moderate heat
during operation.
What to do if the projector does not work when
connecting to a notebook PC?
• Check that the HDMI cable is plugged in correctly.
• Make sure that the notebook PC has been switched to
projector display.
Appendix 15
7 Appendix
Technical data
Technology/optical
Display technology ..............................................DLP
Light source ........................................... OSRAM LED
Resolution ........................................854 x 480 pixel
Resolution supported ..............1920 x 1080 pixel
LED lifetime .......................last over 20,000 hours
Contrast ratio .......................................................600:1
Aspect ratio ............................................................16:9
Throw ratio .............................................................. 1.2:1
Brightness mode .....................................normal/Eco
Screen size (diagonal)...............................10” to 70”
Screen distance ..............................80 cm - 200 cm
Focus adjustment ...........................................manual
Digital zoom ............................................................. yes
Projection modes .................... front, back, ceiling,
back ceiling
Sound
Internal Speaker ......................................................3 W
Connection
USB (on the projector) ...........................power only
USB (on the supplied USB cable) ........... Software
update only
Mini HDMI .................................................................... x1
Analog audio output (3.5mm) .............................. x1
Power source
Power source ......... micro USB port (DC 5V, 2.4A)
Built-in battery ......................................... 3000mAh
.................................................... last up to 3 hours
Product details
Dimensions (W × D × H) .............. 76 x 74 x 34 mm
........................................2.99 x 2.91 x 1.34 inches
Weight .................................................215 g / 0.47 lbs
Operating temperature.......................... 5 °C - 35 °C
Storage temperature ...................................... < 60 °C
Package content
PicoPix Micro+ projector, USB cable, Quick Start
Guide
CE statement
• The product shall only be connected to a
USB interface of version USB 2.0 or higher.
• Adapter shall be installed near the
equipment and shall be easily accessible.
• The operating temperature of the EUT can’t
exceed 35°C and shouldn’t be lower than
5°C.
• The plug is considered as disconnect device
of adapter.
The Declaration of Compliance can be
consulted on the site www.philips.com.
16 Philips · PicoPix Micro+
FCC statement
15�19 Labeling requirements�
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
15�21 Information to the user�
Any changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
15�105 Information to user�
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
FCC ID: 2ASRT-PPX325
Canada regulatory
compliance
This device complies with Industry Canada CAN
ICES-3 (B)/NMB-3(B)
RSS-Gen & RSS-247 statement: This device
complies with Industry Canada RSS standard(s).
Operation is subject to the following two
conditions:
1 This device may not cause interference, and
2 This device must accept any interference,
including interference that may cause
undesired operation of the device.
Other notice
Preservation of the environment as part
of a sustainable development plan is an
essential concern of Screeneo Innovation SA.
The desire of Screeneo Innovation SA is to
operate systems respecting the environment
and consequently it has decided to integrate
environmental performances in the life cycle
of these products, from manufacturing to
commissioning use and elimination.
Packaging: The presence of the logo (green
dot) means that a contribution is paid to an
approved national organisation to improve
package recovery and recycling infrastructures.
Please respect the sorting rules set up locally
for this kind of waste.
Batteries: If your product contains batteries,
they must be disposed of at an appropriate
collection point.
Product: The crossed-out waste bin symbol on
the product means that the product belongs
to the family of electrical and electronic
equipment. In this respect, the European
regulations ask you to dispose of it selectively:
• At sales points in the event of the
purchase of similar equipment.
• At the collection points made available
to you locally (drop-off centre, selective
collection, etc.).
Appendix 17
In this way you can participate in the reuse
and upgrading of Electrical and Electronic
Equipment Waste, which can have an effect on
the environment and human health.
The paper and cardboard packaging used can
be disposed of as recyclable paper. Have the
plastic wrapping recycled or dispose of it in
the non-recyclable waste, depending on the
requirements in your country.
Trademarks: The mentioned references in
this manual are trademarks of the respective
companies. The lack of the trademarks ®
and ™ does not justify the assumption that
these dedicated terminologies are free
trademarks. Other product names used herein
are for identification purposes only and may
be trademarks of their respective owners.
Screeneo Innovation SA disclaims any and all
rights in those marks.
Neither Screeneo Innovation SA nor its affiliates
shall be liable to the purchaser of this product
or third parties for damages, losses, costs, or
expense s incurred by the purchaser or third
parties as a result of accident, misuse, or abuse
of this product or unauthorised modifications,
repairs, or alterations to this product, or failure
to strictly comply with Screeneo Innovation SA
operating and maintenance instructions.
Screeneo Innovation SA shall not be liable for
any damages or problems arising from the use
of any options or any consumable materials
other than those designated as original
Screeneo Innovation SA/PHILIPS products or
Screeneo Innovation SA/PHILIPS approved
products.
Screeneo Innovation SA shall not be held liable
for any damage resulting from electromagnetic
interference that occurs from the use of any
interface cables other than those designated as
Screeneo Innovation SA/PHILIPS products.
All rights reserved. No part of this publication
may be reproduced, stored in a retrieval
system or transmitted in any form or by any
means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior
written permission of Screeneo Innovation SA.
The information contained herein is designed
only for use with this product. Screeneo
Innovation SA. is not responsible for any use of
this information as applied to other devices.
This user manual is a document that does not
represent a contract.
Errors, printing errors and changes are reserved.
Copyright © 2021 Screeneo Innovation SA.
Screeneo Innovation SA
Route de Lully 5c - 1131 Tolochenaz - Switzerland
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are
used under license. Screeneo Innovation SA is the warrantor in relation to the product with which
this booklet was packaged.
2021 © Screeneo Innovation SA. All rights reserved.
PicoPix Micro+
EN