Philips S560/12 User Manual
Displayed below is the user manual for S560/12 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
Important
Read this user manual carefully before you
use the appliance and save it for future
reference.
Danger
- Keep the adapter dry (Fig. 1).
Warning
- The adapter contains a transformer.
Do not cut off the adapter to replace
it with another plug, as this causes a
hazardous situation.
- The appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be supervised to
ensure that they do not play with the
appliance.
- Always unplug the appliance before
you clean it under the tap.
Caution
- Never use water hotter than 80°C to
rinse the appliance.
- Do not use the appliance, adapter or
any other part if it is damaged, as this
may cause injury. Always replace a
damaged adapter or part with one of
the original type.
- Never use compressed air, scouring
pads, abrasive cleaning agents or
aggressive liquids such as petrol or
acetone to clean the appliance.
- Water may leak from the socket at the
bottom of the shaver when you rinse
it. This is normal and not dangerous
because all electronics are enclosed in
a sealed power unit inside the shaver.
Compliance with standards
- This shaver is waterproof and complies
with the internationally approved
safety regulations. It is suitable for use
in the bath or shower and for cleaning
under the tap. For safety reasons, the
shaver can therefore only be used
cordlessly (Fig. 2).
- This Philips appliance complies with all
applicable standards and regulations
regarding exposure to electromagnetic
elds.
General
- The adapter is equipped with an
automatic voltage selector and is
suitable for mains voltages ranging from
100 to 240 volts.
- The adapter transforms 100-240 volts
to a safe low voltage of less than 24
volts.
General description (Fig. 3)
1 Protection cap
2 Shaving unit with shaving head holder
3 Shaving head holder release button
4 On/off button
5 Display
6 Retaining ring
7 Cutter
8 Guard
9 Shaving head holder
10 Trimmer
11 Adapter
12 Small plug
13 Cleaning brush
14 Storage pouch
The display
’Charging’ indication
- When the shaver is charging, the
battery symbol ashes (Fig. 4).
’Battery fully charged’ indication
- When the battery is fully charged,
the battery symbol lights up
continuously (Fig. 5).
- If you leave the shaver connected to
the mains, the light goes out after 30
minutes.
4222.002.5700.1
S560
Register your product and get support at
www.philips.com/welcome
3
12 4
56 7
8 9 10
11 12 13
14 15 16
17 18 19
20 21 22
23 24 25
26 27 28
29 30 31
32 33
’Battery low’ indication
- When the battery is almost empty, the
plug symbol starts ashing (Fig. 6).
- When you switch off the shaver, the
plug symbol continues to ash for a
few more seconds.
Travel lock
You can lock the shaver when you are going
to travel. The travel lock prevents the shaver
from being switched on by accident.
Note: The travel lock cannot be activated
when the shaver is connected to the mains.
Activating the travel lock
1 Press and hold the on/off button until
the travel lock symbol stops ashing
and the motor stops running (Fig. 7).
The travel lock is now activated.
Note: If you release the on/off button before
the travel lock symbol stops ashing, the travel
lock is not activated.
Deactivating the travel lock
1 Press and hold the on/off button until
the travel lock symbol stops ashing
and the motor starts running.
The shaver is now ready for use again.
Note: When you start charging, the travel lock
is deactivated automatically.
Charging
It takes approx. 60 minutes to fully charge
the battery.
When you charge the shaver for the rst
time or after a long period of disuse, let it
charge for 90 minutes.
A fully charged shaver provides up to
40 shaving minutes.
If you have a heavy beard, the shaver may
provide less than 40 shaving minutes. The
number of shaving minutes may also vary
over time, depending on your shaving
behaviour, cleaning habits and beard type.
Charging
Do not charge the shaver in a closed
pouch or in the packaging.
1 Put the small plug in the shaver.
2 Put the adapter in the wall socket.
,The battery symbol on the shaver
ashes to show that the shaver is
charging (see chapter ‘The display’).
Note: When you remove the adapter from the
wall socket and leave the small plug in the
shaver, the shaver may not work for a few
seconds.
Using the shaver
Note: You cannot use the shaver while it is
connected to the mains.
Shaving
Skin adaptation period
Your rst shaves may not bring you the
result you expect and your skin may even
become slightly irritated. This is normal.
Your skin and beard need time to adapt to
any new shaving system.
We advise you to shave regularly (at least
3 times a week) for a period of 3 weeks to
allow your skin to adapt to the new shaver.
During this period, use your new electric
shaver exclusively and do not use other
shaving methods. If you use different shaving
methods, it is more difcult for your skin to
adapt to the new shaving system.
1 Press the on/off button to switch on
the shaver.
2 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 8).
3 Press the on/off button to switch off
the shaver.
4 Clean the shaver after every shave
(see chapter ‘Cleaning and
maintenance’).
Wet shaving
You can also use this shaver on a wet face
with shaving foam or shaving gel.
To shave with shaving foam or shaving gel,
follow the steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to
your skin.
3 Rinse the shaving unit under the tap
to ensure that the shaving unit glides
smoothly over your skin.
4 Press the on/off button to switch on
the shaver.
5 Move the shaving heads over your
skin. Make both straight and circular
movements.
Note: Rinse the shaver under the tap regularly
to ensure that it continues to glide smoothly
over your skin.
6 Dry your face and thoroughly rinse
the shaver with a sufcient amount
of water after every shave. Make sure
you rinse all foam or shaving gel off
the shaver (see also chapter ‘Cleaning
and maintenance’).
Trimming
You can use the trimmer to groom
your sideburns and moustache.
1 Pull the shaving unit straight off the
shaver (Fig. 9).
Note: Do not twist the shaving unit while you
pull it off the shaver.
2 Insert the lug of the trimmer into the
slot in the top of the shaver (1). Then
press down the trimmer (2) to attach
it to the shaver (‘click’) (Fig. 10).
3 Press the on/off button to switch
on the trimmer. You can now start
trimming.
4 Press the on/off button to switch off
the trimmer.
5 Pull the trimmer straight off the
shaver (Fig. 11).
Note: Do not twist the trimmer while you pull
it off the shaver.
6 Insert the lug of the shaving unit into
the slot in the top of the shaver (1).
Then press down the shaving unit (2)
to attach it to the shaver
(‘click’) (Fig. 12).
Cleaning and maintenance
Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive
liquids such as petrol or acetone to clean
the appliance and its accessories.
- Clean the shaver after every shave.
- Clean the shaving heads frequently
with Philips Shaving Head Cleaning
Spray (HQ110) for optimal shaving
performance.
- You can clean the outside of the
shaver with a damp cloth. Do not clean
the shaving unit with a cloth.
Cleaning the shaving unit
Be careful with hot water. Always check if
the water is not too hot, to prevent your
hands from getting burnt.
1 Switch off the shaver.
2 Rinse the shaving unit under a hot tap
for some time (Fig. 13).
Note: You can also clean the shaving unit with
the cleaning brush supplied.
3 After rinsing the appliance under the
tap, hold it upright for 10-15 seconds
to allow water to run out of the
bottom.
4 Press the release buttons on the
shaving unit (1) and pull the shaving
head holder off the shaving unit
(2). (Fig. 14)
5 Rinse the shaving head holder under a
hot tap for 30 seconds (Fig. 15).
Note: You can also clean the shaving head
holder with the cleaning brush supplied.
6 Carefully shake off excess water and
let the shaving head holder dry.
Never dry the shaving head holder with
a towel or tissue, as this may damage the
shaving heads.
7 Reattach the shaving head holder
to the shaving unit (‘click’) (Fig. 16).
Extra-thorough cleaning method
1 Switch off the shaver.
2 Press the release buttons on the
shaving unit (1) and pull the shaving
head holder off the shaving unit
(2) (Fig. 14).
3 Turn the retaining ring anticlockwise
(1) and lift it off the shaving head
(2) (Fig. 17).
Repeat this process for the other retaining
ring.
4 Remove the shaving heads from the
shaving head holder. Each shaving
head consists of a cutter and
guard. (Fig. 18)
Note: Do not clean more than one cutter and
guard at a time, since they are all matching
sets. If you accidentally put a cutter in the
wrong shaving guard, it may take several
weeks before optimal shaving performance
is restored.
5 Clean the cutter with the cleaning
brush supplied (Fig. 19).
6 Clean the inside of the guard. (Fig. 20)
7 After cleaning with the brush, clean
the cutter and guard under the
tap (Fig. 21).
8 Place the cutter back into the guard.
9 Put the shaving heads back into the
shaving head holder (Fig. 22).
Note: Make sure the projections of the
shaving heads t exactly into the recesses.
10 Place the retaining ring on the shaving
head (1) and turn it clockwise (2) to
reattach the retaining ring (Fig. 23).
The retaining ring is xed properly if the
two wings of the retaining ring are located
exactly under the projections of the shaving
head holder.
Repeat this process for the other retaining
ring.
Note: The shaving heads and retaining ring
should be rmly set in place before closing the
shaving unit.
11 Reattach the shaving head holder to
the shaving unit (‘click’). (Fig. 16)
Note: If the shaving unit does not close
smoothly, check if you have positioned the
shaving heads properly and if the retaining
rings are xed properly.
Cleaning the trimmer
Clean the trimmer after every use.
Cleaning the trimmer under
the tap.
1 Switch on the appliance with the
trimmer attached.
2 Rinse the trimmer under a hot tap for
some time (Fig. 24).
3 After cleaning, switch off the appliance.
4 After rinsing the appliance under the
tap, hold it upright for 10-15 seconds
to allow water to run out of the
bottom.
1 Undo the screw in the back panel of
the shaver with a screwdriver (1) and
remove the back panel (2) (Fig. 30).
2 Bend the hooks aside and remove the
power unit (Fig. 31).
3 Break the snap hooks (1) and remove
the front panel of the power unit (2)
(Fig. 32).
4 Take out the battery holder (1) and
cut the battery tags with a pair of
cutting pliers (2) (Fig. 33).
5 Remove the rechargeable battery.
Guarantee and support
If you need information or support, please
visit www.philips.com/support or read
the separate worldwide guarantee leaet.
Guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they are
subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below, visit
www.philips.com/support for a list of
frequently asked questions or contact the
Consumer Care Centre in your country.
Problem Possible
cause
Solution
The
shaver
does not
shave as
well as it
used to.
The shaving
heads are
damaged
or worn.
Replace the
shaving heads
(see chapter
‘Replacement’).
The shaving
heads are
dirty.
Clean the
cutters and
guards with
the cleaning
brush supplied
(see chapter
‘Cleaning and
maintenance’,
section ‘Extra-
thorough clean-
ing method’).
Cleaning the trimmer with the
cleaning brush supplied.
1 Switch off the trimmer.
2 Clean the trimmer with the cleaning
brush. Brush up and down along the
trimmer teeth. (Fig. 25)
Tip: For optimal trimmer performance,
lubricate the trimmer teeth frequently
with Philips Shaving Head Cleaning Spray
(HQ110).
Storage
Note: Make sure the shaving unit is dry before
you store the shaver.
1 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 26).
2 Store the shaver in the
pouch supplied.
Replacement
For maximum shaving performance, we
advise you to replace the shaving heads
every two years. Replace damaged shaving
heads right away.
Only replace the shaving heads with original
SH30 Philips shaving heads. See also chapter
‘Ordering accessories’.
1 Switch off the shaver.
2 Press the release buttons on the
shaving unit and pull the shaving head
holder off the shaving unit (Fig. 14).
3 Turn the retaining ring (1)
anticlockwise (2) and lift it off the
shaving head (3) (Fig. 17).
Repeat this process for the other retaining
ring.
4 Remove the shavings heads from the
shaving head holder and throw them
away (Fig. 27).
5 Place new shaving heads in the
holder (Fig. 22).
Note: Make sure the projections of the
shaving heads t exactly into the recesses.
6 Place the retaining ring on the shaving
head (1) and turn it clockwise (2) to
reattach the retaining ring (Fig. 23).
The retaining ring is xed properly if the
two wings of the retaining ring are located
exactly under the projections of the shaving
head holder.
Repeat this process for the other retaining
ring.
7 Reattach the shaving head holder to
the shaving unit (‘click’) (Fig. 16).
Note: If the shaving unit does not close
smoothly, check if you have positioned the
shaving heads properly and if the retaining
rings are xed properly.
Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go
to your Philips dealer. You can also contact
the Philips Consumer Care Centre in your
country.
The following accessories are available:
- SH30 Philips shaving heads
- RQ575 Philips cleansing brush
- HQ110 Philips Shaving Head Cleaning
Spray
Recycling
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 28).
- The built-in rechargeable shaver battery
contains substances that may pollute
the environment. Always remove the
battery before you discard or hand in
the shaver at an ofcial collection point.
Dispose of the battery at an ofcial
collection point for batteries. If you
have trouble removing the battery, you
can also take the appliance to a Philips
service centre. The staff of this centre
will remove the battery for you and will
dispose of it in an environmentally safe
way (Fig. 29).
Removing the rechargeable
shaver battery
Only remove the rechargeable battery
when you discard the shaver. Make sure
the rechargeable battery is completely
empty when you remove it.
Be careful, the battery strips are sharp.
Problem Possible
cause
Solution
When you
remove
the adapter
from the
wall socket
and leave
the small
plug in the
shaver, the
shaver does
not work
for a few
seconds.
Remove the
small plug from
the shaver.
The
shaver
does not
work,
even
though
it is con-
nected to
the mains.
This shaver
is not
designed
to be used
directly
from the
mains.
Remove the
adapter from
the wall socket
and the small
plug from the
shaver. You can
now switch
on the shaver
again.
My
skin is
irritated
after
shaving.
Your skin
needs time
to get
used to
the Philips
shaving
system.
Skin irritation
during the rst
2-3 weeks of
use is possible.
After this period,
the skin irritation
usually disap-
pears.
The shaving
heads are
damaged
or worn.
Replace the
shaving heads
(see chapter
‘Replacement’).
The
rotation
speed of
the shav-
ing heads
is lower
than
usual.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The re-
chargeable
battery is
low.
Recharge the
battery. See
chapter ‘Charg-
ing’.
Problem Possible
cause
Solution
Long hairs
obstruct
the shaving
heads.
Clean the
cutters and
guards with
the cleaning
brush supplied
(see chapter
‘Cleaning and
maintenance’,
section ‘Extra-
thorough clean-
ing method’).
Shaving
foam or
shaving gel
has accu-
mulated in
the shaving
heads.
Rinse the
shaving heads
thoroughly
with a suf-
cient amount
of water.
The
shaver
does not
work
when I
press the
on/off
button.
The re-
chargeable
battery is
empty.
Recharge the
battery (see
chapter ‘Charg-
ing’).
The travel
lock is
activated.
To deactivate
the travel lock,
press and
hold the on/
off button until
the travel lock
symbol stops
ashing and the
motor starts
running.
The tem-
perature of
the shaver
is too high.
In this case,
the shaver
does not
work.
Let the shaver
cool down. As
soon as the
temperature of
the shaver has
dropped suf-
ciently, you can
switch on the
shaver again.
-請勿讓孩童使用本產品或將本產品
當成玩具。
-在水龍頭下沖洗本產品之前，
請先拔掉產品電源插頭。
警告
-切勿使用超過 80°C 的熱水沖洗
產品。
-如有損壞情況，請勿繼續使用該產
品、轉換器或任何其他零件，否則
可能導致受傷。轉換器或零件如有
受損，請務必以原型號更換之。
-絕對不可使用壓縮空氣、鋼絲絨、
磨蝕性的清潔劑或侵蝕性的液體
(例如汽油或丙酮) 清潔本產品。
-在您沖洗時，水可能會從電鬍刀底
部的插孔流出。此為正常現象，不
會造成危險，因為所有的電子零件
都密封於電鬍刀內的電源裝置中。
符合標準
-這款防水電鬍刀符合國際公認的安
全規範。適合在泡澡或淋浴時使
用，且可在水龍頭底下清潔。基於
安全考量，本電鬍刀只能以無線方
式操作。 (圖 2)
-本飛利浦產品符合所有電磁波暴露
的相關適用標準和法規。
一般
-本轉換器配備有自動電壓選擇器，
適用 100 到 240 伏特的插座電壓。
-轉換器可將 100-240 伏特的電壓轉
換為低於 24 伏特的安全低電壓。
一般說明 (圖 3)
1 保護蓋
2 附電鬍刀刀頭固定座的電鬍刀組
3 電鬍刀刀頭固定座釋放鈕
4 開關按鈕
5 顯示幕
6 固定環
7 刀具
8 刀網
9 電鬍刀刀頭固定座
10 鬢角刀
11 轉換器
12 小插頭
13 清潔刷
14 收納袋
顯示畫面
「充電」指示燈
-電鬍刀充電中時，電池符號會閃
爍。 (圖 4)
Problem Possible
cause
Solution
The
shaving
heads do
not stay
in place.
You did not
x the re-
taining rings
properly.
The retaining
ring is xed
properly if the
two wings of
the retaining
ring are located
exactly under
the projections
of the shaving
head holder.
After
fully
charg-
ing the
shaver, it
provides
less
than 40
shaving
minutes.
If you have a
heavy beard,
the shaver
may provide
less than
40 shaving
minutes. The
number
of shaving
minutes
may also
vary over
time, de-
pending on
your shaving
behaviour,
cleaning
habits and
beard type.
繁體中文
簡介
恭喜您購買本產品並歡迎加入飛利浦！
請於 www.philips.com/welcome 註冊您
的產品，以善用飛利浦提供的支援。
重要事項
在使用本產品前，請先仔細閱讀本使用
手冊，並保留使用手冊以供日後參考。
危險
-請保持轉換器乾燥。 (圖 1)
警示
-轉換器內含一個變壓器。請勿切斷
轉換器而以其他插頭取代，否則會
造成危險。
-本產品不適合供下列人士 (包括小
孩) 使用：身體官能或心智能力退
化者，或是經驗與使用知識缺乏
者。他們需要有負責其安全的人員
在旁監督，或指示產品的使用方
法，方可使用。
6 每次刮鬍，請擦乾臉部，並使用足
量的水徹底沖洗電鬍刀。請確實從
電鬍刀上洗去所有刮鬍膏或刮鬍凝
露(請參閱「清潔與維護」單元)。
修剪
您可以使用鬢角刀修整鬢角與鬍髭。
1 從電鬍刀中垂直抽出電鬍刀組。
(圖9)
注意：當您從電鬍刀中抽出電鬍刀組時，
請勿旋轉。
2 將鬢角刀的突耳插入電鬍刀頂端
的凹槽(1)，再將鬢角刀往下壓(2)
即可安裝到電鬍刀上(會聽見「喀
噠」一聲)。(圖10)
3 按下開關(on/off)按鈕，開啟鬢角
刀電源。這時即可開始修整。
4 按下開關(on/off)按鈕，關閉鬢角
刀電源。
5 從電鬍刀中垂直抽出鬢角刀。
(圖11)
注意：當您從電鬍刀中抽出鬢角刀時，
請勿旋轉。
6 將電鬍刀組的突耳插入電鬍刀頂端
的凹槽(1)，再將電鬍刀組往下壓
(2)即可安裝到電鬍刀上(會聽見
「喀噠」一聲)。(圖12)
清潔與維護
絕對不可使用壓縮空氣、鋼絲絨、磨蝕
性的清潔劑或侵蝕性的液體(例如汽油
或丙酮)清潔本產品與其配件。
-每次刮鬍後均需清潔電鬍刀。
-為得到最佳的刮鬍性能，請經常使
用飛利浦電鬍刀刀頭噴霧清潔劑
(HQ110) 清潔電鬍刀刀頭。
-您可以使用濕布清潔電鬍刀外側。
請勿用布清潔電鬍刀組。
清洗電鬍刀組
請小心使用熱水。隨時檢查熱水是否太
燙，以避免手部燙傷。
1 請關閉電鬍刀電源。
2 將電鬍刀組以熱水沖洗一段時間。
(圖13)
注意：您也可以用產品所附的清潔刷清
潔電鬍刀組。
,電鬍刀的電池符號閃爍，表示電
鬍刀正在充電中(請參閱「顯示畫
面」單元)。
注意：當您將轉換器從電源插座拔除
時，小插頭若仍插在電鬍刀上，電鬍刀
可能有幾秒鐘無法運作。
使用本電鬍刀
注意：您無法在電鬍刀仍連接在電源
上時使用。
刮鬍
皮膚適應期
您第一次刮鬍的結果可能不如您所預
期，皮膚甚至可能稍微刺痛。這是正常
現象。您的皮膚與鬍鬚需要時間適應任
何新的刮鬍系統。
我們建議您定期刮鬍 (每週至少 3 次)
為期 3 週，讓您的肌膚適應新的電鬍
刀。這段期間，請只使用您的新電鬍
刀，不要使用其他的刮鬍方式。如果您
使用不同的刮鬍方式，您的皮膚可能較
難適應新的刮鬍系統。
1 按下開/關(On/Off)按鈕，開啟電鬍
刀電源。
2 將電鬍刀刀頭在皮膚上移動，
請同時用直線及畫圓的方式來移動。
(圖8)
3 按下開/關(On/Off)按鈕，關閉電鬍
刀電源。
4 每次刮鬍後，請清潔本電鬍刀
(請參閱「清潔與維護」單元)。
濕刮
您也可以在沾有刮鬍膏或刮鬍凝露的濕
潤臉部上使用本電鬍刀。
若要在刮鬍時配合使用刮鬍泡或刮鬍凝
膠，請依照下列步驟：
1 在皮膚上抹一點水。
2 將刮鬍泡或刮鬍凝膠抹到皮膚上。
3 將電鬍刀組放在水龍頭下沖洗，
以確保電鬍刀組能在皮膚上平順
移動。
4 按下開/關(On/Off)按鈕，開啟電鬍
刀電源。
5 將電鬍刀刀頭在皮膚上移動，請同
時用直線及畫圓的方式來移動。
注意：定期將電鬍刀放在水龍頭下沖
洗，以確保電鬍刀持續在皮膚上平順
移動。
「電池充滿電」指示燈
-當電池充滿電時，電池符號會持續
亮起。 (圖 5)
-如果您將電鬍刀連接至電源時，
燈號會在 30分鐘後自動熄滅。
「電量不足」指示
-當電池電力即將用盡時，插頭符號
會開始閃爍。 (圖 6)
-當您關閉電鬍刀的電源時，插頭符
號會持續閃爍數秒。
旅行鎖定
在您外出旅行之前，可以設定鎖住電鬍
刀。使用旅行鎖可防止電鬍刀意外開
啟電源。
注意：電鬍刀插接電源時無法啟動旅
行鎖定。
啟動旅行鎖
1 按住開關(on/off)按鈕直到旅行鎖
定符號停止閃爍，且馬達停止運轉
為止。(圖7)
這時即已啟動旅行鎖定。
注意：若您在旅行鎖定符號停止閃爍
前放開開關(on/off)按鈕，則旅行鎖定
不會啟動。
解除旅行鎖
1 按住開關(on/off)按鈕直到旅行鎖
定符號停止閃爍，且馬達開始運轉
為止。
電鬍刀現在已可再度使用。
注意：一開始充電就會自動解除旅行
鎖定。
充電
完整充電約需 60 分鐘。
在您第一次對電鬍刀充電或者長時間沒
有使用後，請讓它連續充電 90 分鐘。
充飽電的電鬍刀可刮鬍 40 分鐘。
若您的鬢鬚濃密，電鬍刀的刮鬍時間可
能少於 40 分鐘。此外，取決於您的刮
鬍方式、清潔習慣和鬍鬚類型，可使用
時間也可能會隨著時日改變。
充電
請勿將電鬍刀置於密閉收納袋中或在包
裝內充電。
1 將小插頭插上電鬍刀。
2 將轉換器插入插座。
3 在水龍頭下沖洗本產品，將其直立
10-15秒，讓水從底部流出。
4 按下電鬍刀組的釋放鈕(1)並將電鬍
刀刀頭固定座從電鬍刀組取下(2)。
(圖14)
5 將電鬍刀刀頭固定座放在熱水龍頭
下沖洗30秒。(圖15)
注意：您也可以用產品所附的清潔刷清
潔電鬍刀刀頭固定座。
6 仔細甩乾多餘的水份之後，讓電鬍
刀刀頭固定座乾燥。
切勿使用毛巾或紙巾擦乾電鬍刀刀頭固
定座，因為此舉可能會造成電鬍刀刀
頭損害。
7 將電鬍刀刀頭固定座重新接上電鬍刀
組(會聽見「喀噠」一聲)。(圖16)
超徹底清潔方法
1 請關閉電鬍刀電源。
2 按下電鬍刀組的釋放鈕(1)並將電鬍
刀刀頭固定座從電鬍刀組取下(2)。
(圖14)
3 將固定環以逆時針方向轉動(1)，
然後將其自電鬍刀刀頭拿起(2)。
(圖17)
就其他固定環重複此項程序。
4 從電鬍刀刀頭固定座上取下電鬍刀
刀頭。每個電鬍刀刀頭均含刀片和
刀網。(圖18)
注意：因為刀片及刀網是成對的一組，
請勿一次清潔多組。如果您不小心將
刀片放進錯誤的電鬍刀刀網中，可能
要花幾週的時間才能恢復最理想的刮
鬍效果。
5 使用隨附於電鬍刀的清潔刷來清潔
刀片。(圖19)
6 清潔刀網內部。(圖20)
7 以小刷子清潔之後，將刀片及刀網
置於水龍頭下沖洗。(圖21)
8 將刀片放回刀網中。
9 將電鬍刀刀頭裝回電鬍刀刀頭固
定座。(圖22)
注意：確定電鬍刀刀頭的凸出部分準確
地安裝於凹處。
問題 可能原因 解決方法
長鬍鬚卡住
電鬍刀刀
頭。
使用隨附的
清潔刷清潔
刀具及刀網
(請參閱「清
潔與維護」
單元的「超
徹底清潔方
法」小節)。
刮鬍泡或刮
鬍凝膠黏附
在電鬍刀刀
頭上。
以足量的水
徹底沖洗電
鬍刀刀頭。
我按下
開/關
(On/
Off) 按
鈕時，
電鬍刀
沒有反
應。
充電式電池
沒電。
將電池重新
充電 (請參閱
「充電」單
元)。
旅行鎖定已
啟動。
若要解除旅行
鎖定，按住開
關 (on/off) 按
鈕直到旅行鎖
定符號停止閃
爍，且馬達
開始運轉為
止。
電鬍刀過
熱。在此情
況下，電鬍
刀將無法使
用。
讓電鬍刀冷
卻。等到電鬍
刀充分降溫，
您就能再度啟
動電鬍刀的電
源。
當您將轉換
器從電源插
座拔除時，
小插頭若仍
插在電鬍刀
上，電鬍刀
會有幾秒鐘
無法運作。
將小插頭從
電鬍刀取
下。
電鬍刀
無法運
作，即
使已經
連接到
電源。
此電鬍刀無
法直接插電
使用。
將轉換器從電
源插座拔除，
並將小插頭
從電鬍刀上
取下。現在您
可以再次開啟
電鬍刀的電
源。
取出電鬍刀的充電式電池
棄置本電鬍刀前，請先取出充電式電
池。當您要取出充電式電池時，請確認
其電力已完全耗盡。
電池固定帶非常銳利，請小心。
1 用螺絲起子(1)轉開電鬍刀的背板
螺絲，拆下背板(2)。(圖30)
2 彎折旁邊的扣鉤，然後取出供電裝
置。(圖31)
3 斷開彈簧鉤(1)，並取下供電裝置的
正面護板(2)。(圖32)
4 取出電池固定座(1)並使用剪鉗(2)
將電池拉片剪斷。(圖33)
5 取出充電式電池。
保固與支援
如果您需要資訊或支援，請造訪：
www.philips.com/support，或另行參閱
全球保證書。
保固限制
電鬍刀刀頭 (刀具和刀網) 由於其耗損
性，因此不在全球保固範圍內。
疑難排解
本單元概述您使用本產品時最常遇到的
問題。如果您無法利用以下資訊解決您
遇到的問題，請造訪 www.philips.com/
support 查看常見問題清單，或聯絡您
所在國家/地區的飛利浦客戶服務中心。
問題 可能原因 解決方法
電鬍刀
不像平
常一樣
運作。
電鬍刀刀頭
毀壞或磨
損。
更換電鬍刀
刀頭 (請參閱
「更換」單
元)。
電鬍刀刀頭
髒污。
使用隨附的
清潔刷清潔
刀具及刀網
(請參閱「清
潔與維護」
單元的「超
徹底清潔方
法」小節)。
2 按下電鬍刀組的釋放鈕，將電鬍刀刀
頭固定座從電鬍刀組取下。(圖14)
3 將固定環(1)以逆時針方向旋轉(2)，
然後將其自電鬍刀刀頭拿起(3)。
(圖17)
就其他固定環重複此項程序。
4 從電鬍刀刀頭固定座上取下電鬍刀
刀頭並丟棄。(圖27)
5 將新的電鬍刀刀頭放入固定座。
(圖22)
注意：確定電鬍刀刀頭的凸出部分準確
地安裝於凹處。
6 將固定環放在電鬍刀刀頭上(1)
並以順時針方向轉動(2)，以重新裝
回固定環。(圖23)
若固定環的兩翼已準確崁入電鬍刀刀頭
固定座的凸出部分下方，則表示固定環
已正確固定。
就其他固定環重複此項程序。
7 將電鬍刀刀頭固定座重新接上電鬍刀
組(會聽見「喀噠」一聲)。(圖16)
注意：若電鬍刀組無法順利關上，
請檢查電鬍刀刀頭安裝位置是否正確，
以及固定環是否確實固定。
訂購配件
若要購買配件或備用零件，請造訪
www.shop.philips.com/service，或者洽
詢您的飛利浦經銷商。您也可以聯絡您
所在國家/地區的飛利浦客戶服務中心。
備有下列配件可供另外選購：
-SH30 飛利浦電鬍刀刀頭
-RQ575 飛利浦潔顏刷
-HQ110 飛利浦電鬍刀刀頭噴霧清
潔劑
回收
-本產品使用壽命結束時請勿與一般
家庭廢棄物一併丟棄。請將該產品
放置於政府指定的回收站，此舉能
為環保盡一份心力。 (圖 28)
-本電鬍刀使用的充電式電池可能含
有會污染環境的物質。將本電鬍刀
丟棄或是送到政府指定回收站前，
請務必先取出電池，並將電池送到
政府指定的電池回收站。若您無法
取出電池，也可將本產品帶到飛利
浦授權服務中心。服務中心會為您
卸下電池，並以對環境無害的方式
處理電池。 (圖 29)
10將固定環放在電鬍刀刀頭上(1)
並以順時針方向轉動(2)，以重新裝
回固定環。(圖23)
若固定環的兩翼已準確崁入電鬍刀刀頭
固定座的凸出部分下方，則表示固定環
已正確固定。
就其他固定環重複此項程序。
注意：應先確定電鬍刀刀頭和固定環已
妥善固定，再關閉電鬍刀組。
11 將電鬍刀刀頭固定座重新接上電鬍刀
組(會聽見「喀噠」一聲)。(圖16)
注意：若電鬍刀組無法順利關上，
請檢查電鬍刀刀頭安裝位置是否正確，
以及固定環是否確實固定。
清潔鬢角刀
每次使用後均需清潔鬢角刀。
將鬢角刀放在水龍頭下沖洗。
1 裝上鬢角刀後，開啟產品電源。
2 將鬢角刀以熱水沖洗一段時間。
(圖24)
3 清潔之後，關閉產品電源。
4 在水龍頭下沖洗本產品，將其直立
10-15秒，讓水從底部流出。
使用隨附的清潔刷來清潔鬢角刀。
1 關閉鬢角刀電源。
2 使用清潔刷清潔鬢角刀。請沿著鬢
角刀的刀齒上下地刷。(圖25)
提示：為使鬢角刀發揮最佳性能，
請經常使用飛利浦電鬍刀刀頭噴霧清潔
劑(HQ110)潤滑鬢角刀的刀齒。
收納
注意：務必等電鬍刀組乾燥之後再收
納電鬍刀。
1 使用後請為電鬍刀蓋上保護蓋以防
損壞，並避免污垢累積在電鬍刀刀
頭中。(圖26)
2 將電鬍刀存放在隨附的收納袋中。
更換
為得到最佳的刮鬍性能，我們建議您請
每兩年更換一次電鬍刀刀頭。有損傷的
電鬍刀刀頭則請要立即更換。
更換電鬍刀刀頭時，限使用原廠 SH30
飛利浦電鬍刀刀頭。亦請參閱「訂購配
件」單元。
1 請關閉電鬍刀電源。
問題 可能原因 解決方法
刮鬍之
後，皮
膚感到
刺痛。
您的皮膚需
要一些時間
才能適應飛
利浦電鬍刀
系統。
開始使用
的第 2 到 3
週，皮膚可
能會有過敏
現象。過了
這段時間，
皮膚過敏的
症狀通常會
消失。
電鬍刀刀頭
毀壞或磨
損。
更換電鬍刀
刀頭 (請參閱
「更換」單
元)。
電鬍刀
刀頭的
旋轉速
度比平
常緩
慢。
過多污垢累
積在電鬍刀
刀頭中。
請清潔電鬍
刀刀頭。請
參閱「清潔
與維護」單
元。
充電式電池
電力不足。
為電池充電。
請參閱「充
電」單元。
電鬍刀
刀頭不
穩固。
固定環未妥
善固定。
若固定環的
兩翼已準確
崁入電鬍刀
刀頭固定座
的凸出部分
下方，則表
示固定環已
正確固定。
電鬍刀
充飽電
後，可
提供的
刮鬍時
間少於
40 分
鐘。
若您的鬢鬚
濃密，電鬍
刀的刮鬍時
間可能少於
40 分鐘。
此外，取決
於您的刮鬍
方式、清潔
習慣和鬍鬚
類型，可使
用時間也可
能會隨著時
日改變。