Philips S7720/85 User Manual
Displayed below is the user manual for S7720/85 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
S7720
Rechargeable Cordless
Tripleheader Shaver
SHAVER 77007700
SERIES 700 0SERIES 700 0
SHAVER 75007500
SERIES 700 0SERIES 700 0
Always here to help you Question?
Contact
Philips
Norelco
Question?
Contact
Philips
Norelco
Register your product and get support at
www.norelco.com/register
2
S7720
ENGLISH 4
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register
North America Corporation.
3. Never operate this shaver/SmartClean System if it has a
damaged cord or charging plug, if it is not working properly, if
it has been dropped or damaged, or dropped into water while
plugged in. For assistance call 1-800-243-3050.
4. Keep the shaver/SmartClean System, cord and charging plug
away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not use the adapter in or near a power outlet that contains
an electric air freshener to prevent damage to the adapter.
7. Do not clean, charge or plug in shaver/SmartClean System
outdoors or operate where aerosol (spray) products are being
used or where oxygen is being administered.
8. Do not use this shaver with a damaged or broken comb, as
facial injury may occur.
9. Always attach plug to shaver/SmartClean System first, then plug
into outlet and then put shaver in SmartClean System. Be
certain plug is inserted firmly into shaver/SmartClean System,
up to mark indicated on plug. To disconnect, turn SmartClean
System off, remove charging plug from outlet.
10. Never put the shaver/SmartClean System in direct sunlight or
store at a temperature above 140°F (60°C).
11. Keep the cord dry at all times. Do not handle with wet hands.
12. To prevent possible damage to the cord, do not wrap cord
around the shaver/SmartClean System.
13. Do not attempt to open the appliance to replace the battery.
14. Only use the power plug and other accessories supplied with
the appliance.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a transformer. Do not
cut off the power plug to replace it with another plug, as this will
cause a hazardous condition.
ENGLISH 5
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric appliance, basic precautions should always
be followed, including the following:
Read all instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a corded shaver/SmartClean System that has
fallen into water. Unplug immediately.
2. Power plug and the accessories connected to it are not for
immersion or for use in shower.
3. Do not use an extension cord with this appliance.
4. Do not place or store a SmartClean System where it can
fall or be pulled into a tub or sink. Do not place or drop a
SmartClean System into water or other liquid.
5. Always unplug this shaver/SmartClean System from the
electrical outlet immediately after use, except when shaver/
SmartClean System is (re)charging.
6. Unplug and remove power supply cord from shaver
before cleaning.
7. The batteries used in this device may present a fire or chemical
burn hazard if mistreated. Do not disassemble, heat above
100ºC (212°F) or incinerate.
WARNING
To reduce the risk of burns, fire, electric shock, or injury
to persons:
1. Close supervision is necessary when this shaver/SmartClean
System is used by, on, or near children or invalids.
2. Use this shaver/SmartClean System for its intended household
use as described in this manual. Do not use attachments or
a cleaning cartridge not recommended by Philips Electronics
ENGLISH
4
7
Table of Contents
Features ...................................................... 8-10
LED Display .............................................12-14
Charge Meter ...............................................14
Before First Use .....................................14-15
Charging ...................................................15-17
Recharging .....................................................17
Quick Charge ...............................................17
Put It To The Test & Shaving Tips ..............18
How to Shave
With An Electric Shaver .......................18-20
Using the SmartClick Trimmer ...........21-22
Using the SmartClick Styler ................22-25
Travel Lock ..............................................25-26
Cleaning ....................................................26-34
Replacing the Shaving Heads ...............35-38
Maintenance ..................................................38
Storage ......................................................38-39
Assistance ......................................................39
Disposal ....................................................39-40
Accessories ...................................................40
Warranty ........................................................41
ENGLISH
6ENGLISH
45 - DAY MONEY-BACK GUARANTEE
To enjoy the closest and most comfortable shave from your new Philips Norelco
Men’s Shaver, the shaver should be used exclusively for 3 weeks. This allows your
hair and skin enough time to adapt to the Philips Norelco Shaving System. If, after
that period of time, you are not fully satisfied with your Philips Norelco Men’s
Shaver, send the product back along with dated sales receipt and we’ll refund
you the full purchase price. The shaver must be shipped prepaid by insured
mail, insurance prepaid, have the original sales receipt, indicating pur-
chase price, the date of purchase, and the money-back guarantee return
authorization form enclosed. We cannot be responsible for lost mail.
The shaver must be postmarked no later than 45 days from the date of purchase.
Philips Norelco reserves the right to verify the purchase price of the shaver and
limit refunds not to exceed suggested retail price.
To obtain money-back guarantee return authorization form,
call 1-800-243-3050 for assistance. Delivery of refund check will
occur 6–8 weeks AFTER receipt of returned product.
98
SmartClick Precision
Trimmer or Styler*
Automatic Worldwide
Voltage 100V to 240V AC
Travel Case
Rechargeable 1-hour full
charge for up to 50 min.
of cordless shaving time
Quick Charge - For
one shave
Cordless - To shave
without a cord
Full 2-Year Warranty
45-Day Money-Back
Guarantee
ENGLISHENGLISH
Features
DynamicFlex Technology
Shaving Unit
• Hair Chamber
captures shaven
hair
Comfort
Rings
Electronic
On/Off Button
Cleaning
Indicator
Replacement
Shaving Heads
Indicator
Travel Lock
'Unplug for use'
Indicator
3-Level
Battery Display
• Shows
remaining
power level
of battery
• Battery Charge,
Full & Low
Indicators *Depending on which shaver you purchased.
11
10 ENGLISH
Features
SmartClean System
SmartClean System Cap
Shaver Holder
On/Off Button
Cleaning
Cartridge
Replacement
Indicator
Cleaning
Indicator
Cleaning
Cartridge
Release
Button
Ready Indicator
Charging
Indicator
Cleaning Cartridge
1312 ENGLISH
◗ Low Battery Indicator
C - When the battery is almost empty (5 or less
shaving minutes left), the bottom charging light
blinks orange.
C ◗ 'Unplug For Use' Indicator
The 'unplug for use' symbol will blink to remind
you the shaver is connected to the outlet.
C ◗ Replacement Shaving Heads Indicator
Every year, depending on your shaving behavior,
the replacement shaving heads indicator lights up
white continuously. See 'Replacing the Shaving
Heads' section for instructions to reset the
shaver. This reminds you that with new shaving
heads you will guarantee yourself optimal shaving
performance.
C ◗ Cleaning Indicator
For optimal shaving performance, we
recommend cleaning the shaver after EACH use.
The blinking faucet will remind you the
shaving unit needs to be cleaned. This happens
after each shave.
ENGLISH
LED Display
◗ Remove any sticker or protective foil from
the display before using shaver.
◗ The display provides the following
information:
◗ Charging Indicator
C - When the shaver is charging, the bottom
charging light blinks and then lights up
continuously. As charging continues, each charging
light will blink and then light up continuously until
the shaver is fully charged.
-Quick charge:When the shaver contains enough
energy for one shave, the bottom charging light
blinks slowly.
◗ Full Charge Indicator
C - When the battery has been fully charged,
all charging lights light up continuously.
After approximately 30 minutes the display
automatically switches off again.
- If the on/off button is pressed during or after
charging, the 'unplug for use' symbol will blink
indicating the shaver is still connected to the
electrical outlet.
◗ Remaining Battery Capacity
- The remaining battery capacity is indicated by
the number of charging lights that are on.
1514
ENGLISH
Important
◗ Only use the power cord or SmartClean
System provided to charge the shaver.
◗ The power plug transforms 100-240V AC to
less than 24V DC.
Charging
◗ Charging, recharging or storing at
temperatures below 40ºF/4,5ºC or higher
than 95ºF/35ºC adversely affects lifetime of
batteries.
◗ Charging or recharging requires one full hour.
◗ A fully charged shaver has a shaving time of up
to 50 minutes.
◗ You may recharge when the display indicates
the battery is almost empty.
◗ This shaver will not operate corded directly
from the electrical outlet.
◗ Do not charge the shaver in a pouch or travel
case.
C 1 Connect cord directly to shaver (1) and
connect the power plug into any 100V to
240V AC outlet (2). Use only the power
cord provided.
◗ An adaptor plug may be necessary for power
cord usage in some foreign countries. Use
an attachment plug adaptor of the proper
configuration for the power outlet.
1
2
ENGLISH
C ◗ Travel Lock
The shaver is equipped with a travel lock function.
You can use the travel lock function when you are
going to store the shaver for a longer period or if
you are going to take the shaver with you when
traveling. See ‘Travel Lock’ section for instructions
on how to use this function.
Charge Meter
◗ Charge Meter monitors amount of remaining
battery power available. Remaining battery
capacity is based on the amount of power
consumed shaving per minute and is
dependent upon your skin and beard type,
whether you use pre-shave lotion, and how
often the styler is used.
◗ Initially your shaver may need to go through 2
or 3 full charge/recharge cycles before
remaining battery capacity indicators begin to
display your accurate battery power left.
Before First Use
◗ Charge the shaver before you start using it
(see ‘Charging’). Make sure the shaver is
switched off before you start charging it.
◗ Remove any sticker or protective foil from
the display before using shaver.
1716 ENGLISH
C 4 Place the shaver into the holder (1), push
shaver back (2) and press down the top
cap to connect the shaver (3) (click).
The shaver will only fit in the SmartClean System
in one direction.
5 The battery indicator lights up to indicate
the shaver is charging.
6 Charging requires one full hour. A fully
charged shaver has a cordless shaving time
of up to 50 minutes.
C 7 Press the top cap down (1), pull the shaver
forward (2) and lift shaver from holder (3).
Recharging
1 Recharging requires one full hour.
Recharge when the display indicates the
battery is almost empty.
Quick Charge
When batteries are empty, recharging the shaver
for 5 minutes gives enough energy for one
cordless shave.
ENGLISH
The power cord will automatically convert to
work on 100V to 240V AC systems.
2 The display on the shaver will indicate
shaver is charging.
3 Charging requires one full hour. A fully
charged shaver has a cordless shaving time
of up to 50 minutes.
Charging Shaver with SmartClean
System
1 Connect the small plug to the SmartClean
System. Connect the power plug into any
100V to 240V AC outlet. Use only the
power cord provided.
C 2 Press the top cap down to open the
SmartClean System.
C 3 Hold the shaver head side down above the
shaver holder.
1
2
3
1
2
3
1918 ENGLISH
Shaving
◗ For best results on skin comfort, pre-trim
your beard if you have not shaved for 3 days
or longer.
C 1 Turn shaver ON by pressing the on/off
button once. Shave against the direction
of beard growth using only circular
movements.
The shaver display shows the remaining battery
capacity.
2 Stretch your skin with your free hand so
blades can lift and cut whiskers. Gently
press shaver to skin so the floating heads
can follow the contours of your face.
DO NOT press too hard. Too much
pressure can pinch the skin into the combs.
3 Turn shaver OFF by pressing the on/off
button once.
The shaver display shows the remaining battery
capacity.
4 Clean the shaver after each use (see
chapter ‘Cleaning’).
C 5 Place the shaver in the SmartClean System
to protect shaver heads.
Wet Shaving
You can also use the shaver on a wet face with
shaving foam or gel.
ENGLISH
Put It To The Test & Shaving Tips
◗ 21 Day Trial and Conversion Process. It is a fact
that your skin and beard need time to adjust to
a new shaving system.
◗ Use your new shaver exclusively for 3 weeks to
fully enjoy the closeness of a Philips Norelco
shave.
◗ At first you may not get as close a shave as you
expect, or your face may even become slightly
irritated. This is normal since your beard and
skin will need time to adjust. Invest 3 weeks
and you’ll soon experience the full joy of your
new shaver.
◗ Stick with it! If you alternate shaving methods
during the adjustment period, it may make it
more difficult to adapt to the Philips Norelco
shaving system.
◗ If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
How To Shave With An Electric
Shaver
C◗ This symbol on the shaver indicates that the
shaver can be used in the bath or shower.
◗ Make sure the SmartClean System does not
get wet or near water.
◗ For hygienic reasons, the shaver should only
be used by one person.
◗ Use this shaver for its intended household use
as described in this manual.
ENGLISH
Using the SmartClick Trimmer
C 1 Pull the shaving unit straight off the shaver.
NOTE: Do not turn the shaving unit while you
pull it off the shaver.
C 2 Insert the raised notch of the SmartClick
trimmer into the slot in the top of the
shaver. Press the trimmer down to attach it
to the shaver. You will hear a ‘click’.
3 Turn shaver ON.
C 4 Hold trimmer to exact hairline desired.
Move trimmer downward with gentle
pressure.
5 Trim beard, moustache or sideburns using
the trimmer.
6 Turn shaver OFF when finished.
7 Thoroughly clean the trimmer (see
‘Cleaning’).
C 8 Pull the trimmer straight off the shaver.
NOTE: Do not turn or twist the trimmer while
you pull it off the shaver.
21
ENGLISH
C 1 Apply some water to your skin.
C 2 Apply shaving foam or gel to your skin.
3 Rinse the shaving unit under the tap
to ensure that the shaving unit glides
smoothly over your skin.
4 Press the on/off button once to switch on
the shaver.
C 5 Move the shaving heads in circular
movements over your skin.
NOTE: Rinse the shaver under the tap regularly
to ensure that it continues to glide smoothly over
your skin.
6 Dry your face and thoroughly clean
the shaver after each use (see chapter
‘Cleaning’).
NOTE: Make sure you rinse all foam or gel off the
shaver.
C 7 Place the shaver in the SmartClean System
to protect heads.
20
ENGLISH
◗ Always comb beard and/or moustache with a
fine comb before using the styler.
◗ The hair length settings on the styler
correspond to the remaining hair length after
trimming. There are 5 settings from 3/64 in. –
3/16 in. (1-5mm).
C 1 Slide the comb straight into the guiding
grooves on both sides of the SmartClick
styler. You will hear a ‘click’.
C 2 Press the length selector and push to the
left or right to select the desired hair
length setting.
To prevent accidentally trimming hairs too short,
start with the maximum setting of 3/16 in.
(5mm).
3 Turn shaver ON.
The shaver display shows the remaining battery
capacity.
C 4 Move the styler upward with gentle
pressure making sure the front of the
comb is in full contact with the skin.
NOTE: If cut hairs accumulate in the comb, turn
the shaver off, remove comb and blow and/or
shake hair out of the comb.
23
ENGLISH
C 9 Insert the raised notch of the shaving unit
into the slot in the top of the shaver. Press
the shaving unit down to attach it to the
shaver. You will hear a ‘click’.
C 10 Place the shaver in the SmartClean System
to protect the heads.
Using the SmartClick Styler
C 1 Pull the shaving unit straight off the shaver.
NOTE: Do not turn the shaving unit while you
pull it off the shaver.
C 2 Insert the raised notch of the SmartClick
styler into the slot in the top of the shaver.
Press the styler down to attach it to the
shaver. You will hear a ‘click’.
Styling with Comb Attachment
◗ Use the SmartClick styler with the comb
attached to trim your beard and moustache.
◗ To prevent trimming your beard and
moustache too short, make sure your hair is
dr y.
22
2
1
ENGLISH
C 7 Insert the raised notch of the shaving unit
into the slot in the top of the shaver. Press
the shaving unit down to attach it to the
shaver. You will hear a ‘click’.
C 8 Place the shaver in the SmartClean System
to protect the heads.
Travel Lock
If you are going to store the shaver for a longer
time period or if traveling, it is possible to lock the
shaver. The travel lock prevents the shaver from
being switched on by accident.
Activating the travel lock
C 1 Press the ON/OFF button for 3 seconds.
◗ The travel lock symbol lights up white
continuously and the lock symbol blinks.
2 The travel lock has now been activated.
25
ENGLISH
Styling without Comb Attachment
◗ Use the SmartClick styler without the comb
to contour your beard, moustache, sideburns
or neckline.
C 1 Pull the comb off the SmartClick styler.
Make sure to grab the comb in the center. Do not
pull at the sides of the comb.
2 Turn shaver ON.
C 3 Contour your beard, moustache,
sideburns or neckline by moving the styler
downward with gentle pressure.
Be careful, the styler cuts hairs very close to the
skin, at a length of 1/32 in (0.5 mm).
4 Turn shaver OFF when finished.
The shaver display shows the remaining battery
capacity.
C 5 Pull the SmartClick styler straight off the
shaver.
NOTE: Do not turn or twist the styler while you
pull it off the shaver.
6 Thoroughly clean the styler and comb (see
‘Cleaning’).
24
3 sec.
ENGLISH
Cleaning the Shaving Unit
The shaving heads may be quickly cleaned after
each use by rinsing with hot water. Water from
the tap should be on a hot setting, BUT BE
CAREFUL TO TEST WATER FIRST SO AS NOT
TO BURN OR SCALD HANDS.
◗ Regular cleaning guarantees better shaving
results.
◗ While rinsing shaving heads, water may drip
out of the base of shaver. This is a normal
occurrence.
1 Turn shaver ON by pressing the on/off
button once.
C 2 For best results rinse the shaving unit by
running under hot water for a few minutes.
3 Turn shaver OFF
C 4 Pull the top portion of the shaving unit
straight off the shaver.
C 5 Rinse the hair chamber under the tap.
27
ENGLISH
Deactivating the travel lock
1 Press the ON/OFF button for 3 seconds.
C 2 The lock symbol blinks and then lights up
continuously. The shaver is now ready for
use.
BThe shaver unlocks automatically when charging
in the SmartClean System or when connected to
an electrical outlet.
Cleaning
◗ Always clean your shaver after each use.
◗ Regular cleaning guarantees better shaving
results.
◗ Never clean, remove or replace shaving unit
while motor is on.
◗ Do not apply pressure to shaving head combs.
Do not touch shaving heads with hard objects
as this may dent or damage precision-made
slotted combs.
◗ Do not use shaver if shaving head combs are
damaged or broken. Facial injury may occur.
◗ Do not use abrasives, scourers or aggressive
liquids such as gasoline or acetone to clean
the shaver.
26
ENGLISH
◗ To avoid evaporation, do not expose cleaning
solution to direct sunlight.
◗ The SmartClean System thoroughly cleans but
does not disinfect your shaver, therefore, do
not share shaver with others.
◗ The charging plug converts 100-240V AC to
less than 24V DC.
◗ Place the
SmartClean System
on a flat,
stable and fluid-resistant surface to avoid any
leakage. Be careful not to tip or move the
SmartClean System
when it is ready for use.
◗ Use this appliance for its intended household
use as described in this manual.
C 1 Place the SmartClean System on a flat, level
surface.
To prevent leaking, do not tilt the SmartClean
System.
C 2 While holding the SmartClean System with
one hand, press the button located on the
side of the SmartClean System (1) and lift
the SmartClean System (2).
C 3 Remove the seal off the cleaning cartridge.
NOTE: ONLY USE PHILIPS NORELCO
SMARTCLEAN CARTRIDGE (MODEL JC302)
WITH THE SMARTCLEAN SYSTEM.
29
ENGLISH
C 6 Rinse the shaving unit under hot tap water.
BE CAREFUL TO TEST WATER FIRST SO AS
NOT TO BURN OR SCALD HANDS.
7 Carefully shake off excess water and let
the shaving unit air dry completely.
NOTE: Do not wipe or dry the shaving unit with
a towel or tissue. This could damage the shaving
heads.
C 8 Press the top portion of the shaving unit
down to attach it to the shaver head
holder. You will hear a ‘click’.
Preparing SmartClean System For
Use
CAUTION: Keep cleaning cartridge(s) out of
reach of children. Do not take internally. Avoid
contact with eyes. In case of eye contact,
thoroughly flush with cold water. If irritation
persists, get medical attention.
Important
◗ Only use this shaver, Smart
Clean System
and
cleaning cartridge provided to charge or clean
shaver.
◗ Other Philips Norelco shavers may not work
with this
SmartClean System.
◗ For optimal cleaning results, replace the
cleaning cartridge every 3 months.
28
1
2
◗ When the cleaning cartridge filter is full, the
replacement symbol blinks indicating the
cleaning cartridge should be replaced. See
'Replacing the SmartClean System Cartridge'.
C 4 Place the cleaning cartridge in the
SmartClean System.
C 5 While holding the SmartClean System with
one hand, gently push the top part of the
SmartClean System back down. You will
hear a 'click'.
When the SmartClean System is ready for use,
do not move appliance to prevent leakage.
Cleaning the Shaver in the
SmartClean System
◗ If the shaver does not contain enough power
for one (1) shave, the SmartClean System
may not work properly. Charge the shaver
in the
SmartClean System
before using the
SmartClean System to clean your shaver.
◗ If you use the shaver with shaving foam or gel,
quickly rinse under hot water before cleaning
in the SmartClean System.
ENGLISH
1 Connect the small plug to the
SmartClean
System
. Connect the power plug into any
100V to 240V AC outlet. Use only the
power cord provided.
2. Place the SmartClean System on a flat,
level surface. Make sure the seal has been
removed from the cleaning cartridge (see
‘Preparing SmartClean System For Use’).
C 3 Press the top cap down to open the
SmartClean System.
C 4 Shake off any excess water from shaver
before placing in the SmartClean System.
C 5 Hold the shaver head side down above the
shaver holder.
C 6 Place the shaver into the holder (1), push
shaver back (2) and press down the top
cap to connect the shaver (3) (click).
The shaver will only fit in the SmartClean System
in one direction.
31
ENGLISH
30
1
2
3
ENGLISH
C 10 Press the top cap down (1), pull the
shaver forward (2) and lift shaver from
SmartClean holder (3).
◗ The SmartClean System automatically turns
off 30 minutes after the cleaning cycle is
complete.
11 Carefully shake off excess liquid and let the
shaving unit air dry completely.
You can also leave the shaver in the SmartClean
System overnight to dry.
Cleaning the Trimmer
Clean the trimmer after each use.
C 1 Attach the trimmer to shaver.
2 Turn shaver ON.
C 3 Rinse the trimmer under hot water. BUT
BE CAREFUL TO TEST WATER FIRST SO
AS NOT TO BURN OR SCALD HANDS.
33
ENGLISH
7 The battery symbol slowly blinks to
indicate shaver is charging.
C 8 Press the ON/OFF button ( ) on the
SmartClean System to start the cleaning
cycle.
The cleaning symbol will blink.
◗ The cleaning cycle takes approximately 10
minutes.
◗ Do not press the ON/OFF button while the
cleaning cycle is running. If this does occur, the
cleaning cycle will stop and the cleaning symbol
stops blinking. The cleaning cycle can
be re-started by pressing the ON/OFF button
once.
◗ If the power plug is disconnected before the
cleaning cycle is complete, reconnect the plug
into the outlet and the cleaning cycle can be
re-started by pressing the ON/OFF button
once.
C NOTE: When the cleaning cartridge filter is full,
the replacement symbol blinks orange. (See
'Replacing the SmartClean System Cartridge').
C 9 When the cleaning cycle is complete and
the shaver is hygienically clean, the ready
symbol lights up continuously.
The battery symbol on the shaver will light up to
indicate the shaver is fully charged.
32
1
2
3
ENGLISH
Replacing the Shaving Heads
◗ Replace the shaving heads once a year for
optimal shaving results.
◗ Replace damaged or worn shaving heads with
model SH70 Philips Norelco shaving heads
only.
Replacement Shaving Heads
Indication
C ◗ The shaving heads symbol lights up
continuously when the shaver is turned off to
remind you to replace your shaving heads to
obtain optimal shaving results.
C 1 Pull the top portion of the shaving unit
straight off the shaver.
C 2 Turn the retaining ring counterclockwise
(1) and lift it off the shaving head (2).
C 3 Remove the shaving heads from the
shaving head holder and discard.
DO NOT discard the retaining ring.
35
ENGLISH
4 Turn the shaver OFF. Shake off excess
water and allow trimmer to air dry
thoroughly.
Tip: For optimal trimmer performance, lubricate
the trimmer teeth with one drop of mineral
oil every 6 months.
Cleaning the Beard Styler
Clean the beard styler after each use.
C 1 Pull the comb off the beard styler.
Make sure to grab the comb in the center. Do not
pull at the sides of the comb.
C 2 Rinse the beard styler and comb under
hot water. BUT BE CAREFUL TO TEST
WATER FIRST SO AS NOT TO BURN OR
SCALD HANDS.
3 Shake off excess water and allow beard
styler and comb to air dry thoroughly.
Tip: For optimal performance, lubricate the beard
styler teeth with one drop of mineral
oil every 6 months.
34
1
2
ENGLISH
36
Replacing the SmartClean System
Cleaning Cartridge
C ◗ For optimal cleaning results, replace the
cleaning cartridge when the replacement
indicator blinks orange or every 3 months.
C 1 While holding the SmartClean System
with one hand, press the cartridge release
button on the side of the SmartClean
System (1) and lift the SmartClean System
(2).
C 2 Remove the empty cleaning cartridge and
pour any remaining cleaning fluid out of
the cleaning cartridge.
You can safely pour the cleaning fluid down the
sink.
3 Discard the empty cleaning cartridge.
Contact your local town or city officials for
recycling information.
4 Remove the seal off the new cleaning
cartridge.
C 5 Place the new cleaning cartridge in the
SmartClean System.
ENGLISH 37
ENGLISH
C 4 Place new shaving head in the holder.
Make sure the notches on both sides of the
shaving heads fit exactly onto the projections in
the shaving head holder.
C 5 Hold the shaving head holder in your hand
and place the retaining ring on the shaving
head holder (1). Turn clockwise (2) to
reattach the retaining ring.
Do not place the shaving head holder on a
surface, as damage may occur.
C NOTE: Each retaining ring has two recesses that
fit exactly into the projections of the shaving
head holder. Turn the ring clockwise until you
hear a click to indicate the ring is fixed into
place.
6 Repeat this process for the other two
cutters and combs.
7 Reattach the shaving head holder to the
bottom part of the shaving unit.
C 8 To reset the shaver, press and hold the
On/Off button for approximately
7 seconds.
36
1
2
1
2
7 sec.
ENGLISH 39
◗ Do not wrap power cord around shaver or
SmartClean System when storing.
◗ Store cord in a safe location where it will not
be cut or damaged.
◗ Do not place or store SmartClean System
where it can fall or be pulled into a tub or
sink, water or other liquid while plugged in.
Assistance
◗ For assistance, visit our website:
www.philips.com/support or
call toll free 1-800-243-3050
◗ Online information is available 24 hours a day,
7 days a week.
Disposal
C ◗ This Philips Norelco shaver contains a
rechargeable lithium-ion battery
which must be disposed of properly.
◗ Contact your local town or city officials
for battery disposal information or call
1-800-822-8837 or www.rbrc.com for battery
drop-off locations.
◗ Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused. For
recycling information, please contact your
38
C 6 While holding the SmartClean System with
one hand, gently push the top part of the
SmartClean System back down. You will
hear a 'click'.
When the SmartClean System is ready for use,
do not move appliance to prevent leakage.
This shaver/SmartClean System has no other
user-serviceable parts. For assistance, call
1-800-243-3050.
Maintenance
◗ Always remove shaver from the SmartClean
System before cleaning appliance.
◗ The SmartClean System and shaver
may be
wiped clean using a damp cloth.
◗ Water from the tap should be on a warm
setting to clean any washable parts.
NOTE: DO NOT place or clean any parts of the
SmartClean System in a dishwasher.
Storage
C ◗ The shaver can be placed in the travel case or
SmartClean System for safe storage.
◗ Be sure shaver is turned off. Remove cord
from outlet before storing in a safe, dry
location where it will not be crushed, banged,
or subject to damage.
ENGLISH
local waste management facilities or visit
www.recycle.philips.com.
◗ For assistance, visit our website,
www.philips.com/support or call toll free:
1-800-243-3050.
Accessories
C ◗ Replacement Shaving Heads
Model SH70 - For maximum shaver
performance, replace your Philips Norelco
shaving heads once a year.
◗ Replacement SmartClick Styler
Model RQ111 - Philips Norelco SmartClick
Styler
◗ Replacement Cleaning Cartridge
Model JC302 - Philips Norelco SmartClean
Cleaning Cartridge, 2-Pack
Model JC303 - Philips Norelco SmartClean
Cleaning Cartridge, 3-Pack
◗ SmartClick Cleansing Brush
Model RQ585 - Philips Norelco SmartClick
Cleansing Brush
◗ Philips Norelco Shaver Accessories may be
purchased at a store near you, or on our
website www.philips.com/store
40 ENGLISH ENGLISH 41
FULL TWO YEAR WARRANTY
Philips Electronics North America Corporation warrants each new Philips Norelco Product,
Model S7720 (except cutters and combs) against defects in materials or workmanship for a
period of two years from the date of purchase, and agrees to repair or replace any defective
product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse,
lack of reasonable care, the affixing of any attachment not provided with the product or loss of
parts or subjecting the product to any but the specified voltage.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/norelco or call 1-800-243-
3050 for assistance. It is suggested that for your protection you return shipments of product
by insured mail, insurance prepaid. Damage occurring during shipment is not covered by this
warranty.
NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America
Corporation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages, so the above exclusion and limitations may not apply to you.
* Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A division of Philips Electronics North America Corporation
P.O.Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco and Tripleheader are registered trademarks of Philips Electronics North America
Corporation.
PHILIPS is a registered trademark of Koninklijke Philips N.V.
© 2016 Philips Electronics North America Corporation. All Rights Reserved.
4222 002 5913 1