Table of Contents
Philips SD700B/00 User Manual
Displayed below is the user manual for SD700B/00 by Philips which is a product in the Portable Speakers category. This manual has pages.
Related Manuals
SD700
www.philips.com/support
User manual
Always there to help you
Register your product and get support at
Question?
Contact
Philips
1EN
Contents
1 Important 2
Hearing safety 2
2 Your Portable Speaker 4
Introduction 4
What's in the box 4
Overview of the product 5
3 Get started 6
Power supply 6
Turn on or off 6
Select a source 7
4 Play 8
Play from Bluetooth-enabled devices 8
Play from a Micro SD card or USB device 9
Play from an external device 9
Listen to FM radio 10
Listen through a headphone 10
Adjust volume 10
5 Product information 11
Specications 11
USB playability information 11
6 Troubleshooting 13
About Bluetooth device 13
7 Notice 14
Compliance 14
Care of the environment 14
Trademark notice 15
2EN
1 Important
Warning
• Never remove the casing of this product.
• Never lubricate any part of this product.
• Never place this product on other electrical equipment.
• Keep this product away from direct sunlight, naked
amesorheat.
• Read these instructions.
• Follow all instructions.
• Do not use this apparatus near water.
• Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
• Do not install near any heat sources such
as radiators, heat registers, stoves, or
otherapparatus(includingampliers)that
produce heat.
• Onlyuseattachments/accessoriesspecied
by the manufacturer.
• Referallservicingtoqualiedservice
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
• The battery shall not be exposed to
excessiveheatsuchassunshine,reorthe
like.
• Apparatus shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on the
apparatus(e.g.liquidlledobjects,lighted
candles).
Hearing safety
Listen at a moderate volume.
• Using headphones at a high volume can
impair your hearing. This product can
produce sounds in decibel ranges that may
cause hearing loss for a normal person,
even for exposure less than a minute. The
higher decibel ranges are offered for those
that may have already experienced some
hearing loss.
• Sound can be deceiving. Over time your
hearing 'comfort level' adapts to higher
volumes of sound. So after prolonged
listening, what sounds 'normal' can actually
be loud and harmful to your hearing. To
guard against this, set your volume to a safe
level before your hearing adapts and leave
it there.
To establish a safe volume level:
• Set your volume control at a low setting.
• Slowly increase the sound until you can
hear it comfortably and clearly, without
distortion.
Listen for reasonable periods of time:
• Prolonged exposure to sound, even
at normally 'safe' levels, can also cause
hearing loss.
• Be sure to use your equipment reasonably
and take appropriate breaks.
Be sure to observe the following guidelines
when using your headphones.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume as your
hearing adapts.
• Do not turn up the volume so high that
you can't hear what's around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
3EN
Note
• The type plate is located on the bottom of the
apparatus.
4EN
2 Your Portable
Speaker
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this speaker, you can:
• listen to FM radio; and
• enjoy audio from Micro SD card, USB
devices, Bluetooth-enabled devices, and
other external devices.
What's in the box
Check and identify the contents of your
package:
• Speaker
• USB cable for charging
• FM antenna
• Short user manual
• Safety¬iceleaet
5EN
Overview of the product
a SRC
• Select an audio source.
b /
• Select a track.
• Search within play.
• Tune to FM radio stations.
c /PAIRING
• In SD, USB, or Bluetooth mode, press
to pause or resume play.
• In Bluetooth mode, press and hold for
three seconds to disconnect Bluetooth
connection or enter pairing mode.
• In FM mode, press and hold for two
seconds to store FM radio stations
automatically.
• In FM mode, press to select a preset
radio station.
d -/+
• Adjust volume.
e
• Turn the product on or off.
f Bluetooth indicator
g Hole for attaching the string
h DC 5V
• Recharge the built-in battery.
i
• Connect a headphone.
ab bcdefg
h
i
j
k
l
m
j AUDIO IN/
• Connect an external audio device.
• Connect FM antenna.
k Display panel
• Show current status.
l
• Connect a USB storage device.
m SD slot
• Connect a Micro SD card.
6EN
3 Get started
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this apparatus. The
model number and serial number are on the
bottom of the apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Power supply
The speaker can operate on the built-in
rechargeable battery.
Note
• Before use, fully charge the built-in battery.
• Rechargeable battery has a limited number of charge
cycles. Battery life and number of charge cycles vary by
use and settings.
To recharge the built-in battery:
Connect the supplied USB cable to:
• the DC 5V socket on the speaker.
• the USB socket on a computer.
DC 5V
Battery status Battery icon ( )
behavior
Low battery Flashing
While charging Solid on
Fully charged or charging
stopped
Off
Turn on or off
• To turn the product on, slide the switch
to the right.
» The product switches to the last
selected source.
• To turn the product off, slide the switch to
the left.
Switch to ECO standby mode
In SD, USB, Audio-in, or Bluetooth mode,
the product switches to ECO standby mode
automatically in the following situations:
• Music playback is stopped for 15 minutes;
• There is no Micro SD card, USB device or
Audio-in cable connected for 15 minutes;
or
• Bluetooth connection is disconnected for
15 minutes.
7EN
To return to the SD/USB/Audio-in/Bluetooth
mode:
• Press to resume playback; or
• Slide the switch to turn the product off
rst,thenturniton.
Select a source
Press SRC repeatedly to select an audio source:
FM tuner, USB, SD, Bluetooth, or Audio-in.
8EN
4 Play
Play from Bluetooth-enabled
devices
With this product, you can listen to audio from
Bluetooth-enabled devices.
Connect a device
Note
• Make sure that your Bluetooth device is compatible
with this product.
• Before pairing a device with this product, read its user
manual for Bluetooth compatibility.
• The product can memorize a maximum of 4 paired
devices.Thefthconnecteddevicewillreplacethe
rstone.
• Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
• Any obstacle between this product and a Bluetooth
device can reduce the operational range.
• Keep away from any other electronic device that may
cause interference.
• The operational range between this product and a
Bluetoothdeviceisapproximately10meters(30feet).
1 Press SRC repeatedly to select Bluetooth
source.
» [bt] is displayed, and the Bluetooth
indicatorashesblueslowly.
2 Press and hold PAIRING until you hear
beep sound.
» The product is ready for pairing.
» TheBluetoothindicatorashesblue
quickly.
3 On your Bluetooth device, enable
Bluetooth and search for Bluetooth
devices.
4 Select [Philips SD700] on your device to
start pairing and connection. If necessary,
enter default password “0000”.
» After successful connection, the
speaker beeps twice, and the
Bluetoothindicatorstopashing.
Bluetooth indicator Status
Flashing blue quickly Ready for pairing a new
device
Flashing blue slowly Trying to connect a
paired device
Solid blue Connected
To disconnect the Bluetooth-enabled device:
• Press and hold PAIRING for three seconds;
• Disable Bluetooth on your device; or
• Move the device beyond the
communication range.
» The product beeps twice, and the
Bluetoothindicatorashesblue.
To reconnect the Bluetooth-enabled device:
• Next time when this product enters
Bluetooth mode, it will reconnect the last
connected device automatically; or
• On your Bluetooth device, select "Philips
SD700" on your Bluetooth menu to start
connection.
To connect another Bluetooth-enabled device:
1 Press and hold PAIRING for three seconds
to disconnect the currently connected
device.
» The product enters Bluetooth pairing
mode.
2 Connect another Bluetooth device.
Play from Bluetooth device
After successful Bluetooth connection, play
audio on the Bluetooth device.
» Audio streams from your Bluetooth
device to the product.
• To pause or resume play, press PAIRING.
9EN
Play from a Micro SD card or
USB device
Note
• Make sure that the USB storage device or Micro SD
card contains playable audio content.
Play from a Micro SD card
1 Press SRC repeatedly to select the SD
card source.
» [SD] is displayed.
2 Insert a Micro SD card into the card slot.
» Play starts automatically.
Play from a USB storage device
1 Press SRC repeatedly to select the USB
source.
» [USB] is displayed.
2 Insert the USB device into the socket.
» Play starts automatically.
Control play
In USB or SD mode, follow the instructions
below to control play.
Button Function
/ Press to skip to the previous or next
track.
Press and hold to fast forward or fast
reverse the track during playback,
then release to resume play.
Press to start, pause, or stop play.
Shufe play
During play, press and hold and
simultaneously for 2 seconds.
» [ ] is displayed.
» All tracks are played randomly.
Play from an external device
With this product, you can listen to an external
audio device such as an MP3 player.
1 Press SRC repeatedly to select AUX
source.
2 Connect an audio input cable with a 3.5
mm connector on both ends to
• the AUDIO IN socket on the speaker.
• the headphone socket on an external
device.
3 Play audio on the device (refer to its user
manual).
10 EN
Listen to FM radio
Tune to FM radio stations
Note
• Keep the product away from other electronic devices
to avoid radio interference.
1 Plug the FM antenna into the AUDIO IN/
socket.
2 Press SRC repeatedly to select FM tuner
source.
3 Press and hold / for two seconds.
» The product tunes to a station with
strong reception automatically.
4 Repeat step 3 to tune to more radio
stations.
To tune to a station manually:
• Press / repeatedlyuntilyound
better reception.
Store FM radio stations automatically
Note
• You can store a maximum of 20 preset radio stations.
In FM tuner mode, press and hold for two
seconds.
» All available radio stations are stored
automatically,thentherststored
radio station is broadcast.
Tip
• You can press / to stop auto scan.
Select a preset radio station
In tuner mode, press repeatedly to select a
preset station.
Listen through a headphone
Plug a headphone into the socket on the
product.
Adjust volume
During play, press -/+ to increase or decrease
volume.
Tip
• You can press and hold -/+ for 2 seconds to increase or
decrease volume continuously.
11EN
5 Product
information
Note
• Product information is subject to change without prior
notice.
Specications
Amplier
Rated Output Power 2 X 1.5W RMS
Frequency Response 60 -20000 Hz, ±3 dB
Signal to Noise Ratio >70 dBA
Aux Input 600mV RMS 22kohm
Tuner (FM)
Tuning Range FM: 87.5-108
MHz
Tuning Grid 50 KHz
- Mono, 26dB S/N Ratio <22 dBf
- Stereo, 46dB S/N Ratio >43 dBf
Search Selectivity >28 dBf
Total Harmonic Distortion <2%
Signal to Noise Ratio >55dB
Bluetooth
Bluetooth Version V3.0+EDR
Bluetooth Frequency
Band
2.402GHz ~
2.48GHz ISM Band
Bluetooth Distance 10m(Freespace)
Speaker
Speaker Impedance 4 ohm
Speaker Driver 4cm full range
Sensitivity >79±3dB/m/W
General information
Power Supply (through
MicroUSBsocket)
5 V 500 mA
Built-in Battery (Li-
polymerbattery)
3.7 V, 850 mAh
Eco Standby Power
Consumption
<0.5 W
Dimensions - Main Unit
(WxHxD)
164 x 63 x 33 mm
Weight - Main Unit 0.35 kg
USB playability information
Compatible USB devices:
• USBashmemory(USB2.0)
• USBashplayers(USB2.0)
• memory cards (requires an additional
card reader to work with this unit;
Some multi-card USB reader may not
besupported.)
Supported formats:
• USBormemoryleformat:FAT12,
FAT16,FAT32(sectorsize:512bytes)
• MP3bitrate(datarate):32-320Kbps
and variable bit rate
• Directory nesting up to a maximum of
8 levels
• Number of albums/ folders: maximum
99
• Number of tracks/titles: maximum 999
• File name in Unicode UTF8 (maximum
length:16bytes)
12 EN
Unsupported formats:
• Empty albums: an empty album is an
album that does not contain MP3/
WMAles,andisnotbeshowninthe
display.
• Unsupportedleformatsareskipped.
Forexample,Worddocuments(.doc)
orMP3leswithextension.dlfare
ignored and not played.
• AAC,WAV,PCMaudioles
• DRMprotectedWMAles(.wav,.m4a,
.m4p,.mp4,.aac)
• WMAlesinLosslessformat
13EN
6 Troubleshooting
Warning
• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).WhenyoucontactPhilips,
make sure that the device is nearby and the
model number and serial number are available.
No power
• Recharge the battery.
No sound or poor sound
•Adjust volume on this product.
•Adjust volume on the connected device.
•Check if you have selected the correct
audio source.
No response from the product
•Turn on the product.
•Recharge the battery.
•Turntheproductoffrst,thenturnit
on to activate the product from standby
mode.
Poor radio reception
•Increase the distance between the product
and other electrical appliances.
•Plug the FM antenna into the AUDIO IN/
socket for better reception.
•Fully extend and adjust the position of the
antenna.
USB device not supported
•The USB device is incompatible with the
unit. Try another one.
About Bluetooth device
The audio quality is poor after connection
with a Bluetooth-enabled device.
•The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
Fail to search out SD700 on your device for
pairing.
•Press and hold PAIRING for three seconds,
and then try again.
Cannot connect with the device.
•The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.
•This product is already connected with
another Bluetooth-enabled device.
Disconnect that device and then try again.
The paired device connects and disconnects
constantly.
•The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
•For some devices, Bluetooth connection
may be deactivated automatically as a
power-saving feature. This does not indicate
any malfunction of this product.
14 EN
7 Notice
Anychangesormodicationsmadetothis
device that are not expressly approved by
Gibson Innovations may void the user’s
authority to operate the equipment.
Compliance
Hereby, Gibson Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions
ofDirective1999/5/EC.Youcanndthe
Declaration of Conformity on www.philips.com/
support.
Care of the environment
Disposal of your old product and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product contains
a built-in rechargeable battery covered by
2522
European Directive 2013/56/EU which cannot
be disposed of with normal household waste.
We strongly advise you to take your product to
anofcialcollectionpointoraPhilipsservice
centre to have a professional remove the
rechargeable battery.
Inform yourself about the local separate
collection system for electrical and electronic
products and rechargeable batteries. Follow
local rules and never dispose of the product
and rechargeable batteries with normal
household waste. Correct disposal of old
products and rechargeable batteries helps
prevent negative consequences for the
environment and human health.
Caution
• Removal of the built-in battery invalidates the warranty
and may destroy the product.
Always bring your product to a professional to
remove the built-in battery.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separateintothreematerials:cardboard(box),
polystyrenefoam(buffer)andpolyethylene
(bags,protectivefoamsheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
15EN
Trademark notice
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Gibson
is under license. Other trademarks and trade
names are those of their respective owners.
Specications are subject to change without notice.
2015 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson
Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used under license from Koninklijke Philips N.V.
SD700_00_UM_V2.0