Table of Contents
Philips SHB9250/00 User Manual
Displayed below is the user manual for SHB9250/00 by Philips which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
www.philips.com/support
User manual
Always there to help you
Register your product and get support at
Question?
Contact
Philips
SHB9250
1EN
Contents
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your Bluetooth wireless headphones 3
What's in the box 3
Other devices 3
Overview of your Bluetooth wireless
headphones 3
3 Get started 5
Charge your headphones 5
Pair the headphones with your mobile
phone 5
4 Use your headphones 7
Connect the headphones to a
Bluetooth device 7
Manage your calls and music 7
Wear your headset 8
5 Technical data 9
6 Notice 10
Declaration of conformity 10
Disposal of your old product and battery 10
Compliance with EMF 10
Trademarks 11
7 Frequently asked questions 12
2EN
1 Important safety
instructions
Hearing Safety
Danger
• To avoid hearing damage, limit the time you use
headphones at high volume and set the volume to a
safe level. The louder the volume, the shorter the safe
listening time is.
Be sure to observe the following guidelines
when using your headset.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
• Do not turn up the volume so high that
you can’t hear what’s around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
• Excessive sound pressure from earphones
and headphones can cause hearing loss.
• Using headphones with both ears covered
while driving is not recommended and may
be illegal in some areas while driving.
• For your safety, avoid distractions from
music or phone calls while in trafc or
other potentially dangerous environments.
General information
To avoid damage or malfunction:
Caution
• Do not expose headphones to excessive heat.
• Do not drop your headphones.
• Headphones shall not be exposed to dripping or
splashing.
• Do not allow your headphones to be submerged in
water.
• Do not use any cleaning agents containing alcohol,
ammonia, benzene, or abrasives.
• If cleaning is required use a soft cloth, if necessary
dampened with a minimum amount of water or diluted
mild soap, to clean the product.
• The integrated battery shall not be exposed to
excessive heat such as sunshine, re or the like.
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
About operating and storage temperatures
and humidity
• Operate or store in a place where
temperature is between -15ºC (5ºF) and
55ºC (131ºF) (up to 90% relative humidity.
• Battery life may be shorter in high or low
temperature conditions.
3EN
2 Your Bluetooth
wireless
headphones
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
With this Philips wireless on-ear headphones,
you can:
• enjoy convenient wireless handsfree calls;
• enjoy and control wireless music;
• switch between calls and music;
• enjoy music on non-Bluetooth devices with
an audio cable.
What's in the box
Philips Bluetooth wireless headphones
SHB9250
USB charging cable
Audio cable
Quick start guide
Other devices
A mobile phone or device (e.g. notebook, PDA,
Bluetooth adapters, MP3 players etc) which
supports Bluetooth and is compatible to the
headphones.
Overview of your Bluetooth
wireless headphones
a Touch panel for music/call/volume/track
control
b LED indicator
c
Power button
d Microphone
e /
Pairing/Equalizer/Mute button
f Micro USB charging slot
d
b
c
a
e
f
g
h
4EN
g NFC detection area
h Audio jack
5EN
3 Get started
Charge your headphones
Note
• Before you use your headphones for the rst time,
charge the battery for 5 hours for optimum battery
capacity and lifetime.
• Use only the original USB charging cable to avoid any
damage.
• Finish your call before charging the headphones, as
connecting the headphones for charging will power the
headphones off.
Connect the supplied USB charging cable to:
• the USB connector of the headphones
and;
• USB power source.
» LED turns white during charging and
turns off when the headphones are
fully charged.
Tip
• Normally, a full charge takes 3 hours.
• When your battery is empty, you can carry on listening
music with an audio cable. Make sure the headphone
are off (and not in idle mode) before using this audio
cable.
Pair the headphones with
your mobile phone
Before you use the headphones with your
mobile phone for the rst time, pair it with a
mobile phone. A successful pairing establishes a
unique encrypted link between the headphones
and mobile phone. The headphones store the
last 4 devices in the memory. If you try to pair
more than 4 devices, the earliest paired device
is replaced by the new one.
There are two ways to pair your headphones
with your mobile phone:
• Manual pairing
• NFC pairing
Manual pairing
1 Make sure that the headphones are fully
charged.
2 Press and hold to turn the headphones
on.
3 Press and hold until the blue and white
LED ashes alternately.
4 Turn on the Bluetooth function of your
mobile phone.
» The headphones are in pairing mode
for 2 minutes.
5 Pair the headphones with the mobile
phone. For detailed information, refer to
the user manual of your mobile phone.
NFC pairing
1 Make sure you turn on the NFC function
on your phone and your phone’s screen
remains active.
2 Place your phone over the headset so that
the NFC detection area of each device can
touch each other.
3 Pair the headphones with the mobile
phone. For detailed information, refer to
the user manual of your mobile phone.
Note
• Make sure your mobile phone has the NFC feature
available and switched on.
• Make sure your mobile phone is not in standby mode.
• Pairing with NFC is only suitable for Android mobile
operating system 4.2 or above.
• Refer to the user manual of your mobile phone to
identify its NFC detection area.
6EN
The following example shows you how to pair
the headphones with your mobile phone.
1 Activate the Bluetooth feature of your
mobile phone, select Philips SHB9250.
2 Enter the headset password "0000" (4
zeros) if prompted. For those mobile
phones featuring Bluetooth 3.0 or higher,
no need to enter a password.
Settings
Devices Found
Select
10:36
Settings Connectivity
Select Back
10:37
Enter Password
****
0000
Settings
Bluetooth
Select Back
10:35
Connectivity
Add
Bluetooth
device
Back
Philips SHB9250
7EN
4 Use your
headphones
Connect the headphones to a
Bluetooth device
1 Turn on your mobile phone/Bluetooth
device.
2 Press and hold to turn the headset on.
» The blue LED ashes.
» The headset is reconnected to the last
connected mobile phone/Bluetooth
device automatically.
Tip
• If you turn on the mobile phone/Bluetooth device or
activate the Bluetooth feature after turning on the
headset, you have to reconnect the headset and mobile
phone/Bluetooth device manually.
• If your mobile phone/Bluetooth device cannot
reconnect automatically, try to reconnect manually
by clicking the headphones' name again under the
Bluetooth setting manual on your mobile phone/
Bluetooth device.
Note
• If the headset fails to connect to any Bluetooth device
within range in 5 minutes, it will switch off automatically
to save the battery life.
Manage your calls and music
On/off
• Turn the headphones on: press and hold
for 2 seconds.
• Turn the headphones off: press and hold
for 4 seconds.
» The white LED is on and fades out.
Voice control
• Siri/Google Now: press .
Music control
• Play or pause music: press once.
• Volume up: slide up or slide up and hold.
• Volume down: slide down or slide down
and hold.
• Skip forward: slide forward.
• Skip backward: slide backward.
• Enable/disable equalizer: Press /EQ
twice.
Call control
• Pick up/hang up a call: tap once.
8EN
• Reject an incoming call: tap and hold.
• Switch caller during a call: slide forward.
• Mute/unmute the microphone in a call:
press / .
Other headphones indicator status
Headphones status Indicator
The headphones
are connected to a
Bluetooth device, while
the headphones in
standby mode or while
you are listening to
music.
The blue LED
ashes for every 8
seconds.
The headphones are
ready for pairing.
The LED ashes
blue and white
alternately.
The headphones are on
but not connected to a
Bluetooth device.
The blue LED
ashes quickly.
Low battery. The white LED
ashes 3 times for
every 10 seconds
until it is out of
power.
Battery is fully charged. White LED is off.
Wear your headset
Adjust the headband to t your head.
Tip
• After use, twist the headphones for easy storage.
9EN
5 Technical data
• 16 hours of music time or talk time
• 300 hours of standby time
• Normal time for a full charge: 3 hours
• Rechargeable Lithium-Polymer battery
(320 mAh)
• 3.5 mm audio jack for corded headphones
mode
• Bluetooth 4.0, Bluetooth mono support
(Headphones Prole - HSP, Hands-Free
Prole - HFP), Bluetooth stereo supported
(Advanced Audio Distribution Prole
- A2DP; Audio Video Remote Control
Prole - AVRCP)
• Operating range: Up to 10 meters (33
feet)
• Digital echo & noise reduction
• Auto power off
Note
• Specications are subject to change without notice.
10 EN
6 Notice
Declaration of conformity
Hereby, WOOX Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions
of Directive 1999/5/EC. You can nd the
Declaration of Conformity on www.p4c.philips.
com.
This product has been designed, tested and
manufactured according the European R&TTE
directive 1999/5/EC.
Disposal of your old product
and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product contains
a built-in rechargeable battery covered by
European Directive 2013/56/EU which cannot
be disposed of with normal household waste.
We strongly advise you to take your product to
an ofcial collection point or a Philips service
centre to have a professional remove the
rechargeable battery.
Inform yourself about the local separate
collection system for electrical and electronic
products and rechargeable batteries. Follow
local rules and never dispose of the product
and rechargeable batteries with normal
household waste. Correct disposal of old
products and rechargeable batteries helps
prevent negative consequences for the
environment and human health.
Remove the integrated battery
Note
• Make sure the headset is disconnected from the USB
charging cable before removing the battery.
If there is no collection/recycling system for
electronic products in your country, you can
protect the environment by removing and
recycling the battery before disposing the
headset.
Compliance with EMF
This product complies with all applicable
standards and regulations regarding exposure to
electromagnetic elds.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
11EN
packaging materials, exhausted batteries and old
equipment.
Trademarks
Bluetooth
The Bluetooth word mark and logos are owned
by the Bluetooth SIG, Inc. and any use of such
marks by WOOX Innovations Limited is under
license.
Siri is a trademark of Apple Inc., registered in
the U.S. and other countries.
Google
Google and the Google Logo are registered
trademarks of Google Inc.
12 EN
7 Frequently
asked questions
My Bluetooth headphones do not switch on.
The battery level is low. Charge the
headphones.
I cannot pair my Bluetooth headphones with a
mobile phone.
The Bluetooth is disabled. Enable the Bluetooth
feature on your mobile phone and turn on
the mobile phone before you turn on the
headphones.
Pairing does not work.
Make sure the headphones are in pairing mode.
• Follow the steps described in this user
manual (see 'Pair the headphones with
your mobile phone' on page 5).
• Make sure that the LED light ashes blue
and white alternately before you release
. Do not stop holding the button if you see
the blue LED only.
The mobile phone cannot nd the
headphones.
•The headphones may be connected to
a previously paired device. Turn off the
connected device or move it out of range.
•Pairing may have been reset or the
headphones have been previously paired
with another device. Pair the headphones
with the mobile phone again as described
in the user manual (see 'Pair the
headphones with your mobile phone' on
page 5).
Voice dialing or redialing does not work on
my mobile phone.
Your mobile phone may not support this
feature.
The other side cannot hear me on the mobile
phone.
The microphone is muted. Press once to
enable the microphone.
My Bluetooth headphones are connected to a
Bluetooth stereo enabled mobile phone, but
music only plays on the mobile phone speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through the
headphones.
The audio quality is poor and crackling noise
can be heard.
The Bluetooth device is out of range. Reduce
the distance between your headphones and
Bluetooth device, or remove obstacles between
them.
The audio quality is poor when streaming
from the mobile phone is very slow, or audio
streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but also supports
A2DP (see 'Technical data' on page 9).
I hear but cannot control music on my
Bluetooth device (e.g. play/pause/skip forward/
backward).
Make sure the Bluetooth audio source supports
AVRCP (see 'Technical data' on page 9).
My headset does not work when the audio
cable is connected.
Microphone function will be deactivated if a
3.5mm audio cable is connected to the headset.
In such case, your headset is only for music
enjoyment.
After using "Google Now", music starts playing
through the mobile phone speaker instead of
headphones, but Bluetooth is still connected,
what can I do?
Press the Siri/Google now button again, music
will resume playing from the headphones.
13EN
How can I restore all original headphones
settings?
When the headphones are powered on and is
not connected to the USB cable, press and hold
and / for 5 seconds until you see the
white LED ashes 5 times.
For further support, visit www.philips.com/
support.
0890
2015 © WOOX Innovations Limited. All rights reserved.
Philips and the Philips’ Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used
by WOOX Innovations Limited under license from
Koninklijke Philips N.V.
UM_SHB9250_00_EN_V1.0
wk1452