Table of Contents
Philips SHD9200/10 User Manual
Displayed below is the user manual for SHD9200/10 by Philips which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
SHD9200
Question?
Contact
Philips
1EN
Contents
1 Important 2
Electric-, Magnetic- and
Electromagnetic Fields (EMF) 2
General information 2
Disposal of your old product 3
Notice for the European Union 3
2 What’s in the box (Fig. A) 4
3 Get Started 5
4 LED indications 7
5 Sound indications 8
6 Product information 9
7 Adaptorspecication 10
8 Frequently asked questions (FAQ) 11
Contents
2EN
1 Important
Hearing safety
Caution
•To prevent possible hearing damage, do not listen at
high volume levels for long periods. Set the volume to a
safe level. The louder the volume, the shorter is the safe
listening time.
Be sure to observe the following guidelines
when using your headphones.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
• Do not turn up the volume so high that
you can’t hear what’s around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
• Excessive sound pressure from earphones
and headphones can cause hearing loss.
Electric-, Magnetic- and
Electromagnetic Fields (EMF)
1. Royal Philips Electronics manufactures and
sells many products targeted at consumers,
which, like any electronic apparatus, in
general have the ability to emit and receive
electromagnetic signals.
2. One of Philips’ leading Business Principles is
to take all necessary health and safety measures
for our products, to comply with all applicable
legal requirements and to stay well within
the EMF standards applicable at the time of
producing products.
3. Philips is committed to develop, produce and
market products that cause no adverse health
effects.
4.Philipsconrmsthatifitsproductsare
handled properly for their intended use, they
aresafetouseaccordingtoscienticevidence
available today.
5. Philips plays an active role in the
development of international EMF and safety
standards, enabling Philips to anticipate further
developments in standardization for early
integration in its products.
General information
• Topreventreorshockhazard: Always
keep this product dry. Do not expose it
to excessive heat by heating equipment or
direct sunlight.
• Nonakedamesources,suchaslighted
candles, should be placed on the apparatus.
• Do not allow your headset to be
submerged in water.
• To clean the product: Use a slightly
dampened chamois cloth. Do not use
cleansing agents containing alcohol, spirits,
ammonia or abrasives as they may harm
the product.
• Do not disassemble the product.
• Transmission range: 100 meters, depending
on ambient conditions.
• Do not operate or store the product in
a place where temperature is below 0°C
(32°F) or above 40°C (104°F) as this may
shorten the battery life.
• This product shall not be exposed to
dripping or splashing.
• The mains plug of AC/DC adaptor is used
as the disconnect device, the disconnect
device shall be readily operable.
3EN
• Only use rechargeable NiMH batteries
(capacity over 700mAh) with your
headphones.
• Other types of rechargeable or alkaline
batteries cannot be charged with this
system.
• AAA alkaline batteries can be used to
operate the headphones.
• Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heatsuchassunshine,reorthelike.
Disposal of your old product
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed with normal household waste.
Please inform yourself about the local rules
on separate collection of batteries because
correct disposal helps to prevent negative
consequences for the environmental and
human health.
Attention should be drawn to the
environmental aspects of battery disposal.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Notice for the European
Union
Hereby, Philips Consumer Lifestyle, BU
Communications, Headphones & Accessories,
declares that this Philips digital wireless headset
SHD9200 is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC. This product has been
designed, tested and manufactured according to
the European R&TTE Directive 1999/5/EC.
4EN
2 What’s in the
box (Fig. A)
1) Headphones 2) Docking station
3) AC/DC adaptor 5V
300mA
4) RCA to RCA
cable
5) 2 x AAA rechargeable
NiMH batteries
6) Quick start
guide
5EN
3 Get Started
Note
•Beforeusingtheheadphonesforthersttime,charge
the supplied batteries for at least 8 hours. Only
rechargeable NiMH batteries can be charged. Use the
batteries (capacity over 700mAh) to ensure the 20
hours' operating time from fully charged.
•AAA alkaline batteries can be used to operate the
headphones.
•Use Philips power adaptor only.
•If no audio input for over 10 minutes, the transmitter
automatically turns to standby.
•The docking station does not transmit audio signal
during charge.
•Digital input only supports PCM (pulse code
modulation).
1 Install/Replace the supplied batteries (Fig.B).
2 Power on the transmitter (Fig.C).
3 Power off the headphones and charge the
headphones (Fig.D).
4 Press INPUT to select ANALOGUE or
DIGITAL mode (Fig.E).
• In ANALOGUE mode, connect the audio
device to LINE IN sockets, then adjust
ATT (Attenuation of audio input signal)
(Fig.F).
• For portable CD player, MP3 player
or other devices with 3.5mm triport
socket output, connect with RCA to
RCA cable (provided) and RCA to
3.5mm plug adaptor (not provided),
then switch ATT to 0dB.
• For Hi-Fi, TV, DVD player or other
devices with RCA socket output,
connect with RCA to RCA cable
(provided), then switch ATT to -8dB.
• In DIGITAL mode, connect the digital
audio device to DIGITAL IN COAXIAL
socket with coaxial cable (not provided)
(Fig.G).
1 Press and hold on the right headphone
for 2 seconds to power on the
headphones (Fig.H).
2 Touch +/- on the right headphone to
adjust the volume (Fig.I).
3 Press the 3D SOUND button on the right
headphone to activate/deactivate the 3D
sound function (Fig.I).
» The LED on the transmitter turns on.
Tip
•You can also adjust the volume on the audio device.
L
L
DIGITAL
OUT
3 sec
6EN
7EN
4 LED indications
Transmitter Headphones
Situation Analogue/Digital Charging 3D sound
LED White Red White Red
Searching Fast blinking --- --- Fast blinking
Connection
established
Blinking --- --- Blinking
Standby Off Off --- ---
Low battery --- --- --- Fast blinking
Charging Off Blinking --- ---
Fully charged --- On --- ---
Non NiMH bat-
teries
--- Off --- ---
3D sound
activated
--- --- On ---
3D sound deac-
tivated
--- --- Off ---
8EN
5 Sound
indications
Situation Sound signal
Low battery One “Beep” per 10
seconds
Turn the volume to
maximum/minimum
level
Alert tone “Beep”
9EN
6 Product
information
Transmitter
System Radio Frequency (RF)
Modulation MSK digital
Carrier
frequency
2,400 - 2,483.5 MHz
Channels 15 (auto-switching)
Radiated output
power
10 mW
Effective
transmission
range
Approx. 100 meters
(depending on ambient
conditions)
Input Level 800 mV (0 dB); 2 V (-8 dB)
Power
requirements
DC 5 V; 300 mA (from the
supplied AC power adaptor)
Headphones
Playback
frequency
range
17 - 24,000 Hz
Signal/Noise
ratio
89 dB Nominal
Distortion < 0.5% THD (Total Harmonic
Distortion)
Channel
Separation
60 dB
Impedance 32 ohm
Power
Requirements
2 x 700 mAh rechargeable
NiMH batteries (supplied) or
commercially available (AAA)
dry batteries
Operating
time
~ up to 20 hours (actual
result may vary)
10 EN
7 Adaptor
specification
Region Adaptor type
number
Input voltage Output voltage Input frequency
Europe
(except
U.K.)
YLS0051A-E050030 100-240V~ 5V , 300mA 50/60Hz
S003IV0500030 100-240V~ 5V , 300mA 50/60Hz
U.K./H.K. YLS0051A-U050030 100-240V~ 5V , 300mA 50/60Hz
S003IB0500030 100-240V~ 5V , 300mA 50/60Hz
8 Frequently
asked questions
(FAQ)
1. Headphones fail to charge.
Possible cause Solution
No battery
installed or
wrongly installed.
Install or replace batteries
properly (Fig.B).
No power
supply to
transmitter.
Make sure that the docking
station is connected to the
local mains power (Fig.C).
Headphones
wrongly placed
into the charging
dock.
Dock the headphones
properly and make sure that
the CHARGING indicator
is on (Fig.D).
2. No sound or distorted sound.
Possible cause Solution
Not set up
properly or
completed.
Make sure that the audio
cable is connected to
AUDIO OUT on the audio
device (Fig.E).
Low battery. Recharge the headphones
(Fig.D).
Audio device
is off.
Turn on the audio device.
Volume of
Analog/Digital
audio input is
too low/high.
Adjust the volume to a
higher/lower and non-
distorted level.
Receiver is too
far away from
transmitter.
Make sure that you use the
product within effective
range.
For further product support, please visit www.
philips.com/support.
0168
Specifications are subject to change without notice
© 2013 Koninklijke Philips Electronics N.V.
All rights reserved.
SHD9200_UM_10_V1.0
WK1303