Philips TAH6005BK/10 User Manual
Displayed below is the user manual for TAH6005BK/10 by Philips which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
User manual
Register your product and get support at
www.philips.com/support
6000 Series
TAH6005
Headphones
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your Wireless TV headphones 3
What's in the box 3
Wireless TV headphones 4
3 Get started 5
Start up 5
Connect 6
LED indications 7
4 Technical data 8
Contents
5 Frequently asked questions 9
1 Important
safety
instructions
Hearing Safety
Be sure to observe the following guidelines
when using your headset.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
• Do not turn up the volume so high that
you can't hear what's around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
• Excessive sound pressure from
earphones and headphones can cause
hearing loss.
• Using headphones with both ears
covered while driving is not recommend-
ed and may be illegal in some areas
while driving.
• For your safety, avoid distractions from
music or phone calls while in trac or
other potentially dangerous environ-
ments.
General information
To avoid damage or malfunction:
About operating and storage
temperatures and humidity
• Operate or store in a place where
temperature is between -10°C (14°F)
and 60°C (140 °F) (up to 90% relative
humidity.
• Battery life may be shorter in high or
low temperature conditions.
Danger
To avoid hearing damage, limit the time you
use headphones at high volume and set the
volume to a safe level. The louder the
volume, the shorter the safe listening time is.
Caution
Do not expose headphones and transmitter to
excessive heat.
Do not drop your headphones and transmitter.
Headphones and transmitter shall not be
exposed to dripping , splashing water.
Do not allow your headphones and transmitter to
be submerged in water.
Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft cloth, if
necessary dampened with a minimum amount of
water or diluted mild soap, to clean the product.
The integrated battery shall not be exposed to
excessive heat such as sunshine, re or the like.
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
2 Your Wireless TV
headphones
What's in the box
Quick start guide
Global Warranty
Safety leaet
Headphones
2 x AAA rechargeable battery
3.5 mm audio cable
AC/DC adaptor
Changeable plug for UK and GS plug
Transmitter
Antenna tube
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips oers, register your
product at www.philips.com/support.
With this Philips over-ear headphones, you
can:
• Enjoy convenient wireless TV show;
• Enjoy and control wireless music.
Overview of your wireless TV
headphones
Power input
3.5mm plug for headphones charging
Audio in (plug with TV)
Power on / o
LED indicator
Channel select switch
LED
Auto-tune (after channel select in transmitter)
Charging socket
Volume +/-
3 Get started
Caution
AAA alkaline batteries can be used to operate
the headphones, but cannot be charged with
this system.
Note
Only use Philips rechargeable shortened
sleeve NiMH batteries with your headphones.
Other types of rechargeable batteries cannot
be charged with this system.
Before using the headphones for the rst
time, charge the supplied batteries for at least
5 hours.
If the volume of the audio source is
insucient, the transmitter automatically turns
o.
The Transmitter does not transmit audio
signal when you charge the battery.
Start up
Put the Antenna tube on the transmitter.
Pull out the ear cushion on the left ear
shell. Insert the supplied AAA x2
batteries.
Connect the power adaptor to main
power socket and 3.5mm plug to
Transmitter.
Plug in the charging cable to the
headphone’s charging socket to charge
the headphones. The LED at the
transmitter will ashing “GREEN”. When
charging nished, the LED will steady
“GREEN” at the transmitter.
+
+
-
-
1
2
3
4
Connect
Charging: “Green” ashing;
Charging nished: “Green” on.
Hi-Fi/TV
“White” on
1 Connect the audio device
• Connect the audio device with a 3.5 mm
audio output. Connect one side of the
supplied 3.5 mm audio cable to the 3.5
mm audio input of the Transmitter and
another side to the 3.5 mm audio
output.
2 Power on the headphones
• Press the power button on the head-
phones. The LED will glow “GREEN” at
the headphones.
3Adjust the input volume
• For device with 3.5mm audio output (e.g.
TV), turn up the volume level on head-
phones will not respond if the connecting
device volume level is too low.
4Auto tune
• Press the auto-tune button on the
headphones for a second to tune to the
signal channel automatically.
Fully charged Green LED
on
N/A
LED indications
Tip
The white LED on transmitter turns o after 5
minutes.
Status LED on
Transmitter
LED on
headphones
Searching
Low battery
level
N/A Green LED
ashing
Connection
established
White
LED on*
N/A
Green LED on
Green LED
ashing
slowly
Charging Green LED
ashing
N/A
• Select the best channel
If there is interference, switch to another
signal channel in transmitter. Then press
the auto-tune button on the headphones
to repeat tuning.
4 Technical data
General specication and features
Music time (headphones variation): 18
hours
Normal time for a full charge: 6 hours
Operating range: up to 100 meters (open
space)
FM solution
Transmission
Carrier / reception frequency:
863.53-864.53 MHz
Transmission power: <9 dBm
Battery
2 x AAA NiMH 700 mAh rechargeable
batteries
Adapter
Philips: YLJXC-080040
Input: 100-240 v~, 50/60 Hz
Output: 8 vdc 400 mA
Tip
For further product support, please visit
www.philips.com/support.
5 Frequently
asked questions
I cannot hear any sound.
• Make sure that you connect the power
source and adapter correctly (see ‘1.
Connect the audio device’ on page 5).
• Make sure that you adjust the volume to
an appropriate level.
• Make sure that the batteries are charged
and inserted properly to the battery
charging slot (see ‘Get started’ on page 5).
• Check if the LED on the transmitter is
white.
• Batteries are defective. Purchase new
ones with the same specications.
The sound is distorted.
• The volume level at the audio source is set
too high.
• The headphones is nearly out of range.
Move it closer to the transmitter.
• The headphones recevies interference
from the nearby electrical appliances.
Move the transmitter away from them.
• The headphones is at a location with thick
walls. Move the transmitter away from
them.
• Adjust the channel setting (see ‘Get
started’ on page 6-7).
• Adjust the volume of the audio device.
When I move my head I hear interfering noise.
The interference can be caused by another
wireless device like Bluetooth, WiFi, router or
2.4 GHz devices. Move the wireless device
away.
The audio quality is poor.
• The headphones is out of range. Reduce
the distance between your headphones
and audio device, or remove obstacles
between them.
• Adjust the channel setting (see ‘Get started’
on page 6-7).
• Adjust the volume of the audio device.
The specication shows an operating range of
100 meters. Why is the actual range shorter?
The operating range is limited by obstacles like
thick walls, doors or ceiling. Move the head-
phones closer to the transmitter.
For further support, visit www.philips.com/support.
9
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license. This product has been
manufactured by and is sold under the responsibility of MMD Hong Kong
Holding Limited or one of its aliates, and MMD Hong Kong Holding
Limited is the warrantor in relation to this product.
UM_TAH6005_10_EN_V1.0