Philips TAPN505BK/00 User Manual
Displayed below is the user manual for TAPN505BK/00 by Philips which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
PN505
5000 Series5000 Series
In Ear
User manual
Register your product and get support at
www.philips.com/support
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your Bluetooth in-ear
headphones 3
What's in the box 3
Other devices 3
Overview of your Bluetooth
wireless headset 4
3 Get started 5
Charge the battery 5
Pair the headphones with your
mobile phone 5
4 Use your headphones 6
Connect the headphones to a
Bluetooth device 6
Connect to ANC(active noise
cancelation) 6
Connect to airline audio systems 7
Manage your calls and music 7
5 Technical data 8
6 Notice 9
Declaration of conformity 9
Disposal of your old product
and battery 9
Remove the integrated battery 9
Compliance with EMF 9
Environmental information 10
Notice of compliance 10
7 Trademarks 11
8 Frequently asked questions 12
Contents
1 Important
safety
instructions
Hearing Safety
Danger
To avoid hearing damage, limit the time you
use headphones at high volume and set the
volume to a safe level. The louder the
volume, the shorter the safe listening time is.
Be sure to observe the following guide-
lines when using your headset.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your
hearing adapts.
• Do not turn up the volume so high
that you can't hear what's around
you.
• You should use caution or tempo-
rarily discontinue use in potentially
hazardous situations.
• Excessive sound pressure from
earphones and headphones can
cause hearing loss.
• Using headphones with both ears
covered while driving is not recom-
mended and may be illegal in some
areas while driving.
• For your safety, avoid distractions
from music or phone calls while in
trac or other potentially dangerous
environments.
General information
To avoid damage or malfunction:
Caution
Do not expose headphones to excessive heat
Do not drop your headphones.
Headphones shall not be exposed to dripping
or splashing.
Do not allow your headphones to be
submerged in water.
Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft doth, if
necessary dampened with a minimum amount
of water or diluted mild soap, to clean the
product.
The integrated battery shall not be exposed to
excessive heat such as sunshine, re or the
like.
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
About operating and storage
temperatures and humidity
• Store in a place where temperature
is between -20°C (-4°F) and 50°C
(122 °F) (up to 90% relative humidi-
ty.
• Operate in a place where tempera-
ture is between -10°C (14°F) and
50°C (122 °F) (up to 90% relative
humidity.
• Battery life may be shorter in high
or low temperature conditions.
2 Your
Bluetooth
in-ear
headphones
What's in the box
Philips Bluetooth in-ear headphones
Philips TAPN505
Replaceable rubber ear caps x 3 pairs
Quick start guide
Other devices
A mobile phone or device (e.g. note-
book, PDA, Bluetooth adapters, MP3
players etc) which supports Bluetooth
and is compatible to the headset (see
'Technical data' on page 8).
Congratulations on your purchase, and
welcome to Philips! To fully benet
from the support that Philips oers,
register your product at
www.philips.com/welcome.
With this Philips in-ear headphones,
you can:
• enjoy convenient wireless
handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.
Audio cable with micro USB plug
USB charging cable (for charging only)
Overview of your
Bluetooth wireless
headset
Voice Assistant button
Micro USB charging slot
ANC On/O/Ambient sound button
ANC On/O/Ambient sound LED indicator
Volime / Track control button
LED indicator
(Power On / O / Pairing)
Microphone
7
8
3 Get started
Charge the battery
Charging case
Note
Before you use your headset for the rst time,
place the headsets in the charging case and
charge the battery for 3 hours for optimum
battery capacity and lifetime.
Use only the original USB charging cable to
avoid any damage.
Finish your call before charging the headset,
as connecting the headset for charging will
power the headset o.
Connect the supplied USB charging
cable to:
• The micro USB charging slot on the
headphones and;
• The charger/USB port of a
computer.
Tip
Normally, a full charge takes 2 hours.
Pair the headphones
with your mobile phone
Make sure that the headphones are
fully charged and turned o.
The headphone remain in
pairing mode for 5 minutes.
Before you use the headphones with
your mobile phone for the rst time, pair
it with a mobile phone. A successful
pairing establishes a unique encrypted
link between the headphones and
mobile phone. The headphones store
the last 8 devices in the memory. If you
try to pair more than 8 devices, the
earliest paired device is replaced by the
new one.
LED turns red during charging and
turns o when the headphones in
fully charged.
Press and hold for 5 seconds
until the blue and red LED ashes
alternately.
Philips PN505
Make sure that the mobile phone is
turned on and its Bluetooth feature
is activated.
The following example shows you how
to pair the headphones with your mobile
phone.
Pair the headphones with the
mobile phone. For detailed infor-
mation, refer to the user manual of
your mobile phone.
Activate the Bluetooth feature of your
mobile phone, select Philips PN505
Enter the headset password “0000”
(4 zeros) if prompted. For those
mobile phones featuring Bluetooth
3.0 or higher, no need to enter a
password.
Headphones status Indicator
ANC is on The white LED
will turn on.
ANC is o The white LED will
turn o.
Ambient sound
The white LED
ashes slowly
4 Use your
headset
Connect the headset to
your Bluetooth device
Connect to ANC (active
noise cancelation)
Turn on your mobile phone/
Bluetooth device.
Press and hold the on/o button to
turn the headphones on.
The blue LED ashes.
The ANC function will be on/o
automatically.
The headphones are recon-
nected to the last connected
mobile phone/ Bluetooth
device automatically. If the last
one is not available, the
headphones try to reconnect to
the second last connected
device.
Tip
If you turn on the mobile phone/Bluetooth
device or activate the Bluetooth feature
after turning on the headphones, you have
to reconnect the headphones and mobile
phone/Bluetooth device manually.
Tip
The function keys will be disabled when
using line-in mode.
Tip
When the ANC function is not required, switch
o the ANC button to continue your call or
listening to music.
Note
The Ambient sound can be enable only when
ANC is also enabled.
If the headphones fail to connect to any
Bluetooth device within range in 5 minutes,
it will switch o automatically to save the
battery life.
Note
You can also use the headphones with
the audio cable provided. Make sure
the headphones turned on before using
the audio cable. Connect the supplied
audio cable to the headphones and
external audio device.
Enable ANC
• Press once ANC button for enable
noise cancelation.
• Press once ANC button for disable
noise cancelation.
Enable Ambient sound mode
ANC LED indicator status
Wired Connection
• Press once ANC button to enable
Ambient sound.
• Press once ANC button disable
Ambient sound.
Connect the audio cable into the
plane adapter.
Insert the adapter into the dual
output jacks in the airplane seat.
Connect the audio cable into the
headphone.
Manage your calls and
music
On/o
Task Button Operation
Turn the
head-
phones on.
On/o,
music/call
control
Press and hold
for 5 seconds.
Turn the
head-
phones o.
On/o,
music/call
control
Press and hold
for 5 seconds.
The blue
LED is
on and
fades
out.
Connect to airline audio
systems
Music control
Task Button Operation
On/o,
music/call
control
Play or
pause music.
Press once.
Press once.
Long press.
Long press.
Adjust volume.
Next track.
Previous track.
Task Button Operation
Voice
assistant
Trigger voice
assistant
Press and
hold
Other headphones indicator status
Headphones status Indicator
The headphones
are connected
to a Bluetooth
device, while the
headphones in
standby mode
or while you are
listening to music.
The blue LED will
turn on.
The headphones
are ready for
pairing.
The LED ashes
blue and red
alternately.
The headphones
are on but not
connected to a
Bluetooth device.
The blue & red LED
ashes quickly
If no connection
can be made, the
headphones will
turn itself o within
5 minutes.
Low battery level. The red LED
ashes until it is
out of power
Battery is fully
charged.
Red LED is o.
Call control
Task Button Operation
Pick up/
hang up a
call.
Switch
caller
during a
call.
On/o,
music/
call control
On/o,
music/-
call
control
Press once.
Press twice.
1 beep.
1 beep.
Need to turn on headphone when connect to airline audio systems.
Note
Voice Assistant
5 Technical data
Note
Specications are subject to change without
notice.
Music time — ANC enabled with
Bluetooth: 7 hours | ANC dsabled
with Bluetooth: 7 hours
Talk time — ANC enabled with
Bluetooth: 7 hours | ANC dsabled
with Bluetooth: 7 hours
Standby time — ANC enabled with
Bluetooth: 160 hours | ANC dsabled
with Bluetooth: 160 hours
Charging time: 2 hours
Rechargeable lithium polymer
battery (180 mAh)
Bluetooth version: 5.0
Compatible Bluetooth proles:
• HSP (Hands-Free Prole-HFP)
• A2DP (Advanced Audio Distri-
bution Prole)
• AVRCP (Audio Video Remote
Control Prole)
Supported audio codec: SBC
Frequency range: 2.505-2.480 GHz
Transmitter power: < 10 dBm
Operating range: Up to 10 meters (33
feet)
Digital echo & noise reduction
Auto power o
Micro-USB port for charging
Supports SBC
Low battery warning: available
Remove the integrated battery
6 Notice
Hereby, MMD Hong Kong Holding Limited
declares that this product is in compli-
ance with the essential requirements and
other relevant provisions of Directive
2014/53/EU. You can nd the Declaration
of Conformity on www.p4c.philips.com.
Declaration of conformity
Disposal of your old
product and battery
Your product is designed and manufac-
tured with high quality materials and
components, which can be recycled and
reused.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This symbol means that the product
contains a built-in rechargeable battery
covered by European Directive
2013/56/EU which cannot be disposed
of with normal household waste. We
strongly advise you to take your product
to an ocial collection point or a Philips
service centre to have a professional
remove the rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and never
dispose of the product and rechargeable
batteries with normal household waste.
Correct disposal of old products and
rechargeable batteries helps prevent
negative consequences for the environ-
ment and human health.
If there is no collection/recycling system
for electronic products in your country,
you can protect the environment by
removing and recycling the battery
before disposing the headphones.
• Make sure the headset is discon-
nected from the charging case
before removing the battery.
Compliance with EMF
This product complies with all applica-
ble standards and regulations regarding
exposure to electromagnetic elds.
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials which
can be recycled and reused if disassem-
bled by a specialized company. Please
observe the local regulations regarding
the disposal of packaging materials,
exhausted batteries and old equipment.
Notice of compliance
The device complies with the FCC rules,
Part 15. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
FCC rules
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to part
15 of the FCC Rules. These limits are
designed to provide reasonable protec-
tion against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment o
and on, the user is encouraged to try to
correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between
equipment and receiver
Connect the equipment into an outlet
on a circuit dierent from that to which
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
Canada:
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence- exempt
RSS(s). Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) This device must accept any interfer-
ence received, including interference
that may cause undesired operation of
the device.
CAN ICES-3(B)/NMB-3(B)
IC Radiation Exposure Statement:
This equipment complies with Canada
radiation exposure limits set forth for
uncontrolled environments.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
Caution:
The user is cautioned that
changes or modications not expressly
approved by the party responsible for
compliance could void the user's
authority to operate the equipment.
7 Trademarks
The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by MMD Hong Kong Holding
Limited is under license. Other trade-
marks and trade names are those of
their respective owners.
Bluetooth
Siri is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
Siri
Google and the Google Logo are
registered trademarks of Google Inc.
Google
8 Frequently
asked
questions
My Bluetooth headset does not turn on.
The battery level is low. Charge the
headset.
I cannot pair my Bluetooth headset with
my Bluetooth device.
The Bluetooth is disabled. Enable the
Bluetooth feature on your Bluetooth
device and turn on the Bluetooth device
before you turn on the headset.
Pairing does not work.
• Put both earpieces into charging case.
• Make sure you have disabled the
Bluetooth function of any previously
connected Bluetooth devices.
• On your Bluetooth device, delete
“Philips SHB2505” from the Bluetooth
list.
• Pair your headset (see ‘Pair the
headset with your Bluetooth device
at the rst time’ on page 6).
How to reset pairing.
Take both headsets out of the charging
case. Press twice on both headsets
Multi-function buttons until the LED
indicator turns white, wait for about 10
seconds. You will hear “Connected”, “Left
Channel”, “Right Channel”, as pairing
successful.
The Bluetooth device cannot nd the
headset.
• The headset may be connected to a
previously paired device. Turn o the
connected device or move it out of
range.
• Pairing may have been reset or the
headset has been previously paired
with another device. Pair the headset
with the Bluetoot device again as
described in the user manual. (see
‘Pair the headset with your Bluetooth
device at the st time’ on page 6).
My Bluetooth headset is connected to a
Bluetooth stereo enabled mobile phone,
but music only plays on the mobile phone
speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through
the headset.
The audio quality is poor and crackling
noise can be heard.
• The Bluetooth device is out of range.
Reduce the distance between your
headset and Bluetooth device, or
remove obstacles between them.
• Charge your headset.
The audio quality is poor when streaming
from the mobile phone is very slow, or
audio streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but alos
supports A2DP and is BT4.0x (or higher)
compatible (see ‘Technical data’ on page
10).
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license. This product has been
manufactured by and is sold under the responsibility of MMD Hong Kong
Holding Limited or one of its aliates, and MMD Hong Kong Holding
Limited is the warrantor in relation to this product.
UM_TAPN505_00_EN_V0.2