Philips TAPS402/10 User Manual
Displayed below is the user manual for TAPS402/10 by Philips which is a product in the Portable Speakers category. This manual has pages.
Related Manuals
Register your product and get support at
www.philips.com/support
User manual
PS402
Smart Speaker
Contents
1 Important 1
Safety 1
Notice 1
2 Your Wireless speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 4
3 Get started 5
5Connect power
6Google home APP
4 You can also use a
BLUETOOTH speaker
7
Connect a Bluetooth device 7
Play from a connected
Bluetooth device
8
Disconnect a device 8
Reconnect a device 8
5 Other features 10
Adjust volume 10
6 10
7 Troubleshooting 11
General 11
Set clock 8
Set alarm time 8
Wireless charging 9
Standby mode 9
EN
1 Important
Safety
Warning
•Never remove the casing of this speaker.
Never place this speaker on other electrical
equipment.
Keep this speaker away from direct
•
•
• Only use attachments or
manufacturer.
Do not place any sources of
danger on the speaker (e.g. lighted
candles).
If your speaker gets wet, clean with
a soft dry cloth and then let it dry
completely in a well-ventilated
place before use next time.
•
•
Note
• The type plate is located on the left side
of the speaker.
Notice
Compliance
Hereby, MMD Hong Kong Holding
Limited declares that this product is in
compliance with the essential
requirements and other relevant
provisions of Directive 2014/30/EU.
Conformity on
www.philips.com/support.
Care of the environment
Disposal of your old product
Your product is designed and
manufactured with high quality
materials and components, which can
be recycled and reused.
our pr
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
1
to this device that are not expressly
approved by MMD Hong Kong Holding
Limited may void the user’s authority to
operate the equipment.
2013/56/EU which cannot be disposed
of with normal household waste. We
strongly advise you to take your product
service centre to have a professional
remove the rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and
never dispose of the product and
rechargeable batteries with normal
household waste. Correct disposal of
old products and rechargeable batteries
helps prevent negative consequences
for the environment and human health.
Caution
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
regarding the disposal of packaging
protective foam sheet.)
Your system consists of materials
which can be recycled and reused if
disassembled by a specialized company.
Please observe the local regulations
materials, exhausted batteries and old
equipment.
EN
2
2 Your
wireless
speaker
Congratulations on your purchase, and
your product at www.philips.com/
welcome.
Introduction
With this speaker, you can enjoy audio
from Bluetooth-enabled devices or
play network audio resources.
What's in the box
Check and identify the contents of your
package:
• Speaker
• Adapter
• Printed materials
EN 3
USB DC IN
Wireless charging/
Wireless charging
Push to talk/
Push to talk(Short press)
standby
(Long press 3s)
Vol+/
USB charging port
Power adapter jack
Mute/
Play/Pause/
Play/Pause/Exit standy mode/
stop timer/alarm(Short press)
Open the bluetooth after successful
authentication (Long press 3s)
Enter standy mode (Long press 10s)
Mode/
Vol-/
Clock light brightness adjust
(Short press)
Bottom light brightness adjust
(Double press)
Switch time display format
(Long press 3s)
1 step down (Short press)
continous steps down
(Long press 3s or 3s+)
continous steps up
Clock / Display panel
Overview of the speaker
[ ]+[ ]Factory data reset.
11
4EN
1 step down (Short press)
(Long press 3s or 3s+)
DC IN 15V 2.5A
Max output 5V 1A current
Charge your mobile devices
Show current time
Automatically setup and
display after networking
(Long press 12s )
10
5
EN
3 Get started
Always follow the instructions in this
chapter in sequence.
Connect power
Caution
Risk of product damage! Make sure that the
power voltage corresponds to the voltage
printed on the back or underside of the clock
radio.
Risk of electric shock! When you unplug the
AC plug, always pull the plug from the socket.
Never pull the cord.
Connect the power adaptor to the wall
outlet.
6EN
https://www.google.com/cast/setup/
Google Home
“Google Home”APP “Google Home”APP
1
2
How to use
Talk to your Google Assistant.
You can start conversation simply
by saying “Ok Google” or short
press .
Sure, here's some
music on
Google Play Music
Ok Google,
Play some music
Place the unit as close as possible
to a wireless LAN router.
Establish a wireless connection
from your smartphone/iPhone to
the wireless LAN router.
Take a note of the SSID and the
password(encryption key) of the
connected wireless LAN router.
some of the wireless LAN routers
have multiple SSIDs.for details,
refer to the operating instructions
supplied with the wireless LAN
router.
On the iPhone,activate the
BLUETOOTH funtion.
“Google Home” uses the
BLUETOOTH funtion to identify
the unit.
Set up Wi-Fi®with app.
Turn on the unit.
Tap to start “Google Home.”
Follow the directions in the app
to set up your unit for Wi-Fi. Set
the unit to the smartphone/
iPhone’s same Wi-Fi connection.
7
EN
4 You can also use as a
BLUETOOTH speaker
With this speaker, you can listen to
audio from Bluetooth-enabled devices
and play music through Bluetooth.
Connect a Bluetooth
device
Note
•
•
•
•
•
•
•
•
can open BTpairing by voice,“Ok,
google open the bluetooth”/
“Ok，google bluetooth pairing”.
speaker will be waiting status,for
pairing other Bluetooth device.
Form your smartphone or other
device’ s BLUETOOTH seting,
unit you setup for Wi-Fi.
If pairing procedure has succeed,
waiting status for pairing will be
released.Speaker will change into
BT connection status.
For BT pairing operation, if can
minutes, speaker will go out.But it
may be changed by Google control.
When Bluetooth is connected or
disconnected, there will be a tone
output.
Make sure that Bluetooth function is
enabled on your device, and your device is
set as visible to all other Bluetooth devices.
Any obstacle between this speaker
and a Bluetooth device can reduce the
operational range.
Keep away from any other electronic
device that may cause interference.
The operational range between this
speaker and a Bluetooth device is
approximately 3 meters.
8EN
Play from a connected
Bluetooth device
After successful Bluetooth connection,
play audio on the connected device.
» Audio streams from your Bluetooth
device to the speaker.
•To pause or resume play, press .
Tip
•You can also use your Bluetooth device to
control play.
Disconnect a device
• Disable Bluetooth on your device;
Move the device beyond the
communication range.
•
Reconnect a device
• When you turn on the speaker,
If not successful, select your
Bluetooth device name on your
Bluetooth menuto start reconnection.
•
Set clock
Long press 3 seconds to
set 12/24 hour format.
Automatically setup and display after
networking.
1Clock
AM/PM
2
•
Set alarm timer
You can setup alarm/timer by Google
Assistant.
Input Key: Short press
Press key during Alarm ringing,
then Stop Alarm.
•
9EN
Color warm white: normal /charging
complete.
Color orange: charging.
Color orange blink: charging error.
•
•
•
Wireless charging Standby mode
•
Module Description
GVA lighting Bottom lighting clock
OFF OFF(No wireless charging) On After authentication
OFF OFF(No wireless charging) Reset state
- On(wireless charging) - Keep on
--|--
（blink)
•
•
•
•
•
Triggering conditions
1. Google authentication succeeded.
2. No operation(including key and
hotword use) for 15 minutes and
automatically enters the network
standby mode.
Exit condition
1. Any user operation (including voice
wake up, button operation or APP
control).
2. Speaker power is controlled within
2W.
Suspend mode
Precondition:Power On
Operation:
1. Suspend in: Keep press for 10s+
2.Suspend out: press
Description:
1.USB charge out stop;
Wireless charge out still run,
2.Speaker power is controlled within
0.5W.
Network standby
10 EN
Adjust volume
-/+
Tip
•-/+
•
6
Note
•Product information is subject to change
without prior notice.
Rated output
2 x 8 W
Acousic
frequency
response
60-20000 Hz
Speaker driver 2 x 1.5” full range, 8Ω
Bass 1 x passive
enhancement radiator
Bluetooth version V4.2
Bluetooth AVRCP V1.5, A2DP1.2
Bluetooth 2.402GHz~
frequency band 2.480GHz ISM Band
/ Output power /BDR:7±2dBm
EDR:4±2dBm
USB output 5V, 1A
charging
Power 100-240v~
5 Other features
50-60Hz(AC Input)
DC output 15V 2.5A
You can press and hold to increase or
decrease volume continuously.
When the volume reaches the maximum,
the speaker beeps twice.
Support wireless Max power about
charge 10W
WIFI standby <2W
power
consumption
Standby <0.5W
consumption
Dimensions
- Main unit 223 x 87 x 94 mm
(W x H x D)
Weight
- Main unit 1.01 kg
During music playback,press to
increase or decrease volume.
11
EN
7 Trouble-
shooting
Warning
•Never remove the casing of this device.
To keep the warranty valid, never try to
repair the system yourself.
If you encounter problems when using
this device, check the following points
before requesting service. If the problem
remains unsolved, go to the Philips Web
page (www.philips.com/support). When
you contact Philips, make sure that the
device is nearby and the model number
and serial number are available.
General
No power
·Recharge the speaker.
No sound
·Adjust volume on this product.
·Adjust volume on the connected
device.
·Make sure that your Bluetooth
operational range.
No response from the speaker when
pressing any key.
·
back on.
GENERAL DESCRIPTION OF EUT:
Max.e.i.r.p.:IEEE 802.11a:17.97dBm
IEEE 802.11n(HT20):16.94dBm
IEEE 802.11n(HT40):15.86dBm
IEEE 802.11ac(VHT20):17.93dBm
IEEE 802.11ac(VHT40):16.96dBm
IEEE 802.11ac(VHT80):16.92dBm
BT（2402-2480MHz）:8.07dBm
BT LE（2402-2480MHz）: 9.00dBm
WIFI 2.4GHz(2412-2472MHz):19.94dBm
WIFI 5GHz(5150- 5250MHz): 17.93dBm
WIFI 5GHz(5250- 5350MHz): 17.97dBm
WIFI 5GHz(5470 -5725MHz): 17.92dBm
WIFI 5GHz(5725-5850MHz):13.84dBm
In all EU member states, operation of
5150-5350MHz is restrictedto indoor use
only.
•
•
•
2019 © MMD Hong Kong Holding Limited.All rights reserved.
This product has been manufactured by,and is sold under the responsibility of MMD
Hong Kong Holding Limited,and MMD Hong Kong Holding Limited.is the warrantor in
relation to this product. Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V.and are used under license.
TAPS402_00 _UM_V 1.0