Philips TAS7807W/00 User Manual
Displayed below is the user manual for TAS7807W/00 by Philips which is a product in the Portable Speakers category. This manual has pages.
Related Manuals
Register your product and get support at：
www.philips.com/support
User manual
Wireless Speaker
7000 Series
S7807
EN 1
Contents
1 Important 2
Safety 2
2 Your wireless speaker 3
Introduction 3
What's in the box 3
Overview of the speaker 3
4 Play from Bluetooth devices 5
Play from Bluetooth devices 5
Multi-point connection 6
Control playback
Control phone call
Trigger voice assistant of
your mobile device
Pairing for stereo mode
6
6
6
7
5 Product information 7
6 Troubleshooting 8
General 8
Bluetooth 8
7 Notice 9
Compliance 9
Care of the environment 9
FCC and IC statement 10
Trademark notice 10
3 Get started 4
Charge the built-in battery 4
4
Turn on/o
EN2
1 Important
Safety
Important safety instructions
• Make sure that the power supply
voltage corresponds to the voltage
on the back or the underside of
the unit.
• The speaker shall not be exposed
to dripping or splashing.
• Do not place any source of danger
on the speaker (e.g. liquid lled
objects, lit candles).
• Make sure that there is enough free
space around the speaker for
ventilation.
• Please use the speaker safely in an
environment with temperature
between 0℃ and 45℃.
• Only use attachments and accessories
specied by the manufacturer.
Battery safety precautions
• Danger of explosion if a battery is
incorrectly replaced. Replace only
with the same or equivalent type.
• A battery (battery pack or battery
installed) shall not be exposed to
excessive heat such as sunshine,
re or the like.
• A battery in extreme high or low
temperatures during use, storage or
transportation, and low air pressure at
high altitude can pose safety hazards.
• Do not replace a battery with an
incorrect type that can defeat a
safeguard (for example, some lithium
battery types).
• Disposing a battery into re or a
hot oven, mechanically crushing
or cutting a battery can result in
an explosion.
• Leaving a battery in an extremely
high temperature surrounding, or
an extremely low air pressure
environment may result in an
explosion or leakage of ammable
liquid or gas.
Warning
• Never remove the casing of this speaker.
• Never lubricate any part of this speaker.
• Place this speaker on a at, hard and
stable surface.
• Never place this speaker on other
electrical equipment.
• Only use this speaker indoors. Keep this
speaker away from water, moisture and
liquid-lled objects.
• Keep this speaker away from direct
sunlight, naked ames or heat.
• Risk of explosion if a battery is replaced
by an incorrect type.
EN 3
What's in the box
Check and identify the contents of your
package:
• Speaker
• USB cables
• Quick start guide
• Safety sheet
• Worldwide warranty
• Strap
Overview of the speaker
1
324
9 7 56
8
10
2 Your wireless
speaker
Congratulations on your purchase, and
welcome to philips! To fully benet
from the support that philips oers,
register your product at
www.philips.com/support.
• Enter Bluetooth pairing mode.
• Clear Bluetooth pairing
information.
3
•
1
Turn the speaker on or o.
• Press and hold to enter stereo
pairing mode.
2
• In Bluetooth mode, press to
pause or resume play.
• Respond to an incoming call
through Bluetooth connection.
• Press and hold to trigger voice
assistant of your mobile device.
4
• Decrease volume.
8
• Charge the built-in battery.
DC IN
10
• Increase volume.
7
6Microphone
Power/Bluetooth LED indicator
• Power/Bluetooth light.
5
Battery level indicators
• Show the charging progress.
• Show the battery level: To check
battery status, press any other
keys but not , as will trigger
the power o.
9
EN4
3 Get started
Always follow the instructions in this
chapter in sequence.
Charge the built-in
battery
The speaker is powered by a built-in
rechargeable battery.
Note
• Fully charge the built-in battery before
using.
• When the speaker is turned on and the
battery is low, the Power/Bluetooth
LED indicator blinks red.
Connect the USB-C socket on the
speaker to an outlet (5V 3A) by
using the provided USB cable.
INPUT: 5V 3A
OUTPUT: 5V 2A
LED 4LED 2LED 1 LED 3
Power/
Bluetooth LED
Power on
When the speaker is being charged,
Power/Bluetooth LED blinks red slowly.
When the speaker is fullycharged,
Power/Bluetooth LED is solid white.
The speaker could charge an external
device via USB cable.
Power o
When the speaker is being charged,
Power/Bluetooth LED blinks red slowly.
When the speaker is fully charged,
Power/Bluetooth LED is o.
Battery power
Full Solid white
Solid white OFF
OFF
OFF
Blinking
Red
Solid
white
Solid
white
OFF
LED1 LED2 LED3 LED4
Power/
Bluetooth LED
＞80%
50% - 80%
20% - 40%
Low battery ＜ 20%
EN 5
4 Play from
Bluetooth
devices
1 Press to turn the speaker on. It
will enter Bluetooth pairing mode
automatically. You can also press
and hold for 3 seconds to enter
Bluetooth pairing mode.
2 Enable Bluetooth and select
"Philips S7807" in the Bluetooth
list on your device for pairing.
If a message prompts for
permission for Bluetooth
connection, conrm it.
If a password is required, enter
0000 and then conrm.
3
Play audio on your Bluetooth
device to start music streaming.
Caution
• Risk of speaker damage! Make sure the
power supply voltage corresponds to the
voltage printed on the back or the
underside of the speaker.
• Risk of electric shock! When unplug the
USB cable, always pull the plug from the
socket. Never pull the cable.
• Use only a USB cable specied by the
manufacturer or sold with this speaker.
Note
The speaker will turn o automatically
if there is no audio signal from
Bluetooth for 15 minutes.
•
Press to turn the speaker on.
You will hear the prompt sound.
To turn the speaker o, press
You will hear the prompt sound.
again.
Play from Bluetooth
devices
With this speaker, you can enjoy audio
from your Bluetooth device.
Note
• Make sure that the Bluetooth function
is enabled on your device.
• The maximum distance for pairing the
speaker and your Bluetooth device is
20 meters (66 feet).
• Keep away from any other electronic
device that may cause interference.
EN6
Power/Bluetooth
LED indicator Description
Blinking white
quickly Ready for pairing
Blinking white
slowly
Reconnecting the last
connected device
Solid white Connected
Note
• To disconnect a device, press and hold
for 3 seconds until the Power/
Bluetooth LED indicator blinks white
quickly.
• To clear the pairing information, press
and hold for 8 seconds until the
Power/Bluetooth LED indicator blinks
white slowly for 3 times.
•Pair the speaker to two devices,
e.g. mobile phone and notebook.
Pairing
•Music can only be played from one
device at a time. The other device
will be reserved for phone calls.
•Pause the audio from one device to
start playing audio from the other
device.
Switch between devices
Note
• Receiving a call on Device 2 will pause
playback on Device 1. The call will be
routed automatically to your speaker.
• Ending the call will resume playback
from Device 1 automatically.
Multi-point connection
Control playback
During music playback
Press to pause or resume play
Press twice to play the next track
Adjust the volume
Control phone call
Press to answer or end a call
Press and hold to reject a call
Adjust the volume
Trigger voice assistant
of your mobile device
Press and hold to trigger voice
assistant of your mobile device
Adjust the volume
EN 7
5 Product
information
Note
• Product information is subject to change
without prior notice.
General information
USB port 5V 3A
Built-in Lithium battery 7.4V, 5000mAh
Dimensions (W x H x D)
280 x 104 x 104 mm
Operation Ambient
IP protection class
0 ℃~45 ℃
IP67*
Weight (main unit) 1896 g
Amplier
Output power (RMS) 40 W
Frequency response 60 Hz - 20 KHz
Signal to noise ratio > 75dB
Speaker
Impedance 4 Ω
Maximum input power 15 W
Drivers
Bluetooth
Bluetooth version 5.2
Frequency range 2402 - 2480 MHz
Maximum
transmition power
< 10 dBm
Compatible
Bluetooth proles
HFP V1.7
Bluetooth range up to 20 m
2 x 71 mm drivers
2 x 31 mm tweeters
Pairing for stereo mode
Two identical wireless speakers
(Philips S7807) can pair with each other
for stereo sound.
*The IP67 rating means the speaker driver is
dust tight and can be submerged for up to
30 minutes at a depth of up to 1 m.
Note
• Any speaker can be used as the primary
speaker.
• The speaker connected to a Bluetooth
device can only be used as the primary
speaker.
• Before stereo pairing, make sure that the
secondary speaker is under Bluetooth
pairing mode.
• Keep a maximum distance of 20 meters
(66 feet) between the speaker and your
Bluetooth device.
• In stereo mode, the button operation on
the secondary speaker is as same as that
of the primary speaker.
1 Press to power on both speakers,
and they will enter Bluetooth pairing
mode automatically. The speaker
connected to your Bluetooth device
will be used as the primary speaker.
2 On both speakers, press and hold
to enter stereo pairing mode until
the LED blinks red and white
alternatively. You will hear a prompt
sound when successfully connected
and Power/Bluetooth LED is solid
white.
3 Press on either speaker. The
music will be played through both
speakers.
To exit the stereo mode, press and hold
the on either speaker.
Passive radiators 2
6
Troubleshooting
Warning
• Never remove the casing of the speaker.
To keep the warranty valid, never try to
repair the speaker yourself.
If you encounter problems when using
this speaker, check the following points
before requesting service. If the problem
remains unsolved, go to the Philips
website (www.philips.com/support).
When you contact philips, ensure that
the speaker is nearby and the model
number and serial number are available.
General
No power
• Make sure the speaker is fully
charged.
• Make sure the USB socket of the
speaker is properly connected.
• As a power-saving feature, the
speaker turns o automatically
15 minutes after no audio signal
is received.
No sound
• Adjust the volume on this speaker.
• Adjust the volume on the connected
device.
•
Make sure that your Bluetooth
device is within the operational
range.
No response from the speaker
• Restart the speaker.
Bluetooth
The audio quality is poor after
connection with a Bluetooth-enabled
device
•
The Bluetooth reception is poor. Move
the device closer to this speaker or
remove any obstacle between them.
Fail to nd [Philips S7807] on your
Bluetooth device for pairing
• Press and hold for 3 seconds to
enter Bluetooth pairing mode, and
then try again.
Cannot connect with your Bluetooth
device
• The Bluetooth function of your
device is not enabled. Refer to the
user manual of your device to nd
out how to enable the function.
• This speaker is not in pairing mode.
• This speaker is already connected to
another Bluetooth-enabled device.
Disconnect and try again.
EN8
EN 9
7 Notice
Compliance
Hereby, TP Vision Europe B.V. declares
that this product is in compliance with
the essential requirements and other
relevant provisions of Directive 2014/
53/EU. You can nd the Declaration of
Conformity on www.philips.com/support.
Care of the environment
Disposal of your old product and battery
Your product is designed and
manufactured with high quality
materials and components, which
can be recycled and reused.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This symbol means that the product
contains batteries covered by European
Directive 2013/56/EU which cannot be
disposed of with normal household
waste.
Any changes or modifications made
to this device that are not expressly
approved by MMD Hong Kong Holding
Limited may void the user's authority to
operate the equipment.
Inform yourself about the local separate
collection system for electrical and
electronic products and batteries. Follow
local rules and never dispose of the
product and batteries with normal
household waste. Correct disposal of
old products and batteries helps prevent
negative consequences for the
environment and human health.
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buer) and polyethylene (bags,
protective foam sheet).
Your system consists of materials which
can be recycled and reused if
disassembled by a specialized company.
Please observe the local regulations
regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Removing the integrated batteries
Make sure the product is disconnected
from power before removing the
integrated battery.
For illustration purposes only
Disposal of a battery into re or a hot
oven, or mechanically crushing or
cutting of a battery, can result in
an explosion.
(4) Consult the dealer or an experienced
radio/TV technician for help.
RF Warning Statement
The device has been evaluated to meet
general RF exposure requirements. The
device can be used in portable
exposure conditions without restriction.
Trademark notice
The Bluetooth® word mark and logos
are registered trademarks owned by the
Bluetooth SIG, Inc. and any use of such
marks by MMD Hong Kong Holding
Limited is under license.
Other trademarks and trade names are
those of their respective owners.
EN10
FCC and IC statement
Warning:Changes or modications
not expressly approved by the party
responsible for compliance could void
the user’s authority to operate the
equipment.
Note: This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment
o and on, the user is encouraged to try
to correct the interference by one or
more of the following measures:
(1) Reorient or relocate the receiving
antenna. (2) Increase the separation
between the equipment and receiver.
(3) Connect the equipment into an
outlet on a circuit dierent from that to
which the receiver is connected.
FCC information
The device complies with the FCC rules,
Part 15. Operation is subject to the
following two conditions:
This device may not cause harmful
interference, and.
This device must accept any
interference received, including
interference that may cause
undesired operation.
IC-Canada: CAN ICES-3(B)/NMB-3(B)
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any
interference, including interference
that may cause undesired operation
of the device.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license.
This product has been manufactured by and is sold under the
TAS7807_00_UM_V1.0
responsibility of MMD Hong Kong Holding Limited or one of its aliates,
and MMD Hong Kong Holding Limited is the warrantor in relation to this product.
Specications are subject to change without notice.