Philips TAT2205BL/00 User Manual
Displayed below is the user manual for TAT2205BL/00 by Philips which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
2000 Series
TAT2205 | TAT2235 | TAT2245
Headphones
User manual
www.philips.com/support
Register your product and get support at
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your Bluetooth wireless
earpieces 3
What's in the box 3
Other devices 3
Overview of your Bluetooth
wireless earpieces 4
3 Get started 5
Charge the battery 5
Pair the earpieces with your
Bluetooth device at the rst
time 6
Pair the earpieces with another
Bluetooth device 6
4 Use your headphones 7
Reconnect the earpieces to your
Bluetooth device 7
Power on/o 7
Manage your calls and music 7
LED indicator status 8
How to wear 8
5 Factory reset the earpieces 9
6 Technical data 10
7 Notice 11
Declaration of conformity 11
Disposal of your old product
and battery 11
Compliance with EMF 12
Environmental information 12
Notice of compliance 12
8 Frequently asked questions 13
Contents
1 Important
safety
instructions
Hearing Safety
Danger
yTo avoid hearing damage, limit the time you
use headphones at high volume and set the
volume to a safe level. The louder the
volume, the shorter the safe listening time is.
Be sure to observe the following guide-
lines when using your earpieces.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your
hearing adapts.
• Do not turn up the volume so high
that you can't hear what's around
you.
• You should use caution or tempo-
rarily discontinue use in potentially
hazardous situations.
• Excessive sound pressure from
earphones and headphones can
cause hearing loss.
• Using headphones with both ears
covered while driving is not recom-
mended and may be illegal in some
areas while driving.
• For your safety, avoid distractions
from music or phone calls while in
trac or other potentially dangerous
environments.
General information
To avoid damage or malfunction:
Caution
yDo not expose headphones to excessive heat
yDo not drop your headphones.
yHeadphones shall not be exposed to dripping
or splashing.
yDo not allow your headphones to be
submerged in water.
yDo not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
yIf cleaning is required use a soft doth, if
necessary dampened with a minimum amount
of water or diluted mild soap, to clean the
product.
yThe integrated battery shall not be exposed to
excessive heat such as sunshine, re or the
like.
yDanger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
About operating and storage
temperatures and humidity
• Operate or store in a place where
temperature is between 0°C (32°F)
and 60°C (140 °F) (up to 90%
relative humidity.
• Battery life may be shorter in high
or low temperature conditions.
2 Your
Bluetooth
wireless
earpieces
What's in the box
True wireless in-ear headphones
Philips TAT2205/TAT2235/TAT2245
Replaceable rubber ear caps x 2 pairs
Charging case
Quick start guide
Other devices
A mobile phone or device (e.g. note-
book, PDA, Bluetooth adapters, MP3
players etc) which supports Bluetooth
and is compatible to the earpieces
(see 'Technical data' on page 10).
Congratulations on your purchase, and
welcome to Philips! To fully benet
from the support that Philips oers,
register your product at
www.philips.com/welcome.
With this Philips wireless earpieces, you
can:
• enjoy convenient wireless
handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.
USB-C charging cable (for charging only)
Overview of your
Bluetooth wireless
earpieces
c Microphone and LED indicator (earphone)
d Multi-function buttons
e LED indicator (charging case)
f USB-C charging slot
3 Get started
Charge the battery
Charging case
Note
yBefore you use your earpieces for the rst
time, place the earpieces in the charging case
and charge the battery for 2 hours for
optimum battery capacity and lifetime.
yUse only the original USB charging cable to
avoid any damage.
yFinish your call before charging the earpieces,
as connecting the earpieces for charging will
power the earpieces o.
Connect one end of the USB cable into
the charging case, and another end into
the power source.
• Charging process is veried by the
blue LED light on the front panel,
• When the charging case is fully
charged, the blue light goes on.
Tip
yThe charging case serves as a portable backup
battery for charging the earpieces. When the
charging case is fully charged, it supports 3 full
recharge cycle for the earpieces.
Earpieces
• Charging process is veried by white
LED light on the earpieces.
• When the earpieces is fully charged,
the white light goes o.
Tip
yNormally, a full charge takes 2 hours (for the
earpieces or charging case).
Place the earpieces in the charging case.
The earpieces start charging.
The charging case starts charging.
4 blue LED lights ashing every 1s in
cycles for 0-25% power
1st blue LED lights stay on and 2nd, 3rd &
4th LED lights turn on successively, ashing
once every 1s for 25-50% power
While charging earpieces, Blue LED will
light on.
4th blue LED lights ashes once every 1s
and others stay on for 75-100% power
1st and 2nd blue LED lights stay on and 3rd
& 4th lights turn on successively, ashing
once every 1s for 50-75% power
Battery LED indicator on
Charging case
Both earpieces are now
powered on and are paired
with each other.
The earpieces is now in pairing
mode and is ready to pair with a
Bluetooth device (e.g. a mobile
phone).
Turn on the Bluetooth function of
your Bluetooth device.
Note
yAfter powering on, if the earpieces cannot nd
any previously connected Bluetooth device, it
will automatically switch to pairing mode.
In right earpieces, it has voice
“Connected”and LED goes o on
both earpieces and ash 1 time
every 10s. You can use your device
to play music or make a call.
Pair the earpieces with your
Bluetooth device. Refer to the user
manual of your Bluetooth device.
Philips TAT2205/
TAT2235/ TAT2245
Turn on the Bluetooth function of
your Bluetooth device, select Philips
TAT2205/TAT2235/TAT2245
Enter the earpieces password
“0000” (4 zeros) if prompted. For
those Bluetooth devices featuring
Bluetooth 3.0 or higher, no need to
enter a password.
The following example shows you
how to pair the earpieces with
your Bluetooth device.
Pair the earpieces with
your Bluetooth device at
the st time
Make sure that the earpieces is fully
charged.
Auto power on: open the charging
capsule, the earpieces discharged
and the blue LED indicator ash for 3
times with “power on” voice prompt;
Manual power on: on both earpieces
press and hold the multi-function
buttons for approxinmately 3s.
The right earphone led ashes
alternately in white and blue, and
the left earphone LED is o for 10s
and the blue LED ashes once.
Blue LED
ashes once
for 10s
LED ashes
alternately in
white and blue
Tip
Note
yThe earpieces cannot connect to more than 1
device at the same time. If you have two paired
Bluetooth devices, only turn on the Bluetooth
function of the device that you want to connect.
yIf you turn on the Bluetooth function of your
Bluetooth device after turning on the earpieces,
you have to go to the Bluetooth menu of the
device and connect the earpieces to the device
manully.
yIf the earpieces fails to connect to any
Bluetooth device within 5 minutes, it will turn o
automatically to save the battery life.
yIn some Bluetooth devices, connection may not
be automatic. In this case, you have to go to the
Bluetooth menu of your device and connect the
earpieces to the Bluetooth device manually.
If no device is connected, the
earpieces will automatically
turn o after 5 mins.
Both earpieces are now
powered on and are paired
with each other automatically.
The earpieces will search the
last connected Bluetooth device
and reconnect to it automatical-
ly. If the last connected one is
not available, the earpieces will
search and reconnect to the
second last connected device.
4 Use your
earpieces
Turn on the Bluetooth function of
your Bluetooth device.
Take both earpieces from the charging
case, the earpieces will power on and
reconnect automatically.
Connect the earpieces to
your Bluetooth device
Philips TAT2205/
TAT2235/TAT2245
Note
yThe earpieces stores 1 device in the memory. If
you try to pair more than 2 devices, the earliest
paired device is replaced by the new one.
Single earpieces pairing
(Mono mode)
Pair the earpieces with
another Bluetooth device
Take the right earpieces (“Master
device”) from the charging case, the
earpiece will power on automatically.
There will be a voice “Power on” from
right earpieces.
Turn on the Bluetooth function on
your device, search for “Philips
UT102” tap to connect. (Please refer
to P.6)
Once the pairing succeed, you will
hear a voice “Connected” and the
indicator light will be o.
If you have another Bluetooth device
that you want to pair with the earpieces,
make sure the Bluetooth function in any
other previously paired or coonected
devices are turned o. Then follow the
steps in ‘Pair the earpieces with your
Bluetooth device at the rst time’.
Task
Music control
Turn the
earpieces
on.
Right and
left
earpieces
Right/Left
earpieces
Take both
earpieces
from the
charging
case or
press and
hold for 3s
Place both
earpieces in
charging
case.
Press and
hold for 5s.
Turn the
earpieces
o.
Play or
pause music
Skip forward Left
earpieces
Press and
hold for 2s
Skip
backward
Right
earpieces
Press and
hold for 2s
Right/Left
earpieces
Press once
Power on/o
Manage your calls and
music
Multi-
function
button
Operation
Task Multi-
function
button
Operation
LED indicator status
Call control
Pick up/hang
up call
Reject an
incomging
call
Right/Left
earpieces
Press and
hold for 1s
Right/Left
earpieces
Press twiceSiri/Google
The earpieces is
connected to a
Bluetooth device.
The earpieces is
powered on.
The earpieces is
pairing mode.
The earpieces is
on but not
connected to a
Bluetooth device.
The blue and
white LED will
ashes. If no
connection can be
made, the
earpieces will turn
itself o within 5
minutes.
The white LED
ashes 3 times.
The blue and
white LED ashes.
The white LED
light goes o and
blue light ashing
once every 10s.
Right/Left
earpieces
Press once
Task Multi-
function
button
Operation
Voice control
Task
Earpieces status Indicator
Multi-
function
button
Operation
5 Factory reset
the earpieces
How to wear
Low battery level
(earpieces).
Low battery level
(charging case).
Only the rst blue
LED goes on
You will hear
‘battery low’ on
the earpieces.
The white LED
ash twice.
Battery LED indicator on
earpieces status
Battery is fully
charged(earpieces)
The white LED on
the earpieces is o
Battery is fully
charged(charging
case).
The four blue LED
on the charging
case is on.
It will show a battery indicator on
Bluetooth device after connected to
earpieces.
If you encounter any pairing or connection
issue, you can follow the following
procedure to factory reset your earpieces.
On your Bluetooth device, go to the
Bluetooth menu and remove
Philips TAT2205/TAT2235/TAT2245
from the device list.
Turn off the Bluetooth function of your
Bluetooth device.
Put both earpieces back to charging
case. Both earpieces flashes white led.
Press and hold both earpieces
function button for 4s,until earpieces
flashes twice white led .
To pair the earpieces with a Bluetooth
device, turn on the Bluetooth function
of your Bluetooth device, select
Philips TAT2205/TAT2235/TAT2245
6 Technical data
Note
ySpecications are subject to change without
notice.
Earpieces
Music time: 4 hours (additional 8 hrs
with charging case)
Talk time: 3 hours (additional 7 hrs
with charging case)
Standby time: 50 hours
Charging time: 2 hours
Rechargeable lithium ion battery: 40
mAh on each earpiece
Bluetooth version: 5.1
Compatible Bluetooth proles:
• HSP (Hands-Free Prole-HFP)
• A2DP (Advanced Audio Distri-
bution Prole)
• AVRCP (Audio Video Remote
Control Prole)
Supported audio codec: SBC
Frequency range: 2.402-2.480 GHz
Transmitter power: < 4 dBm
Operating range: Up to 10 meters (33
feet)
Charging case
Charging time: 2 hrs
Rechargeable Li-ion battery: 320mAh
Remove the integrated battery
7 Notice
Hereby, MMD Hong Kong Holding Limited
declares that this product is in compli-
ance with the essential requirements and
other relevant provisions of Directive
2014/53/EU. You can nd the Declaration
of Conformity on www.p4c.philips.com.
Declaration of conformity
Disposal of your old
product and battery
Your product is designed and manufac-
tured with high quality materials and
components, which can be recycled and
reused.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This symbol means that the product
contains a built-in rechargeable battery
covered by European Directive
2013/56/EU which cannot be disposed
of with normal household waste. We
strongly advise you to take your product
to an ocial collection point or a Philips
service centre to have a professional
remove the rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and never
dispose of the product and rechargeable
batteries with normal household waste.
Correct disposal of old products and
rechargeable batteries helps prevent
negative consequences for the environ-
ment and human health.
If there is no collection/recycling system
for electronic products in your country,
you can protect the environment by
removing and recycling the battery
before disposing the headphones.
• Make sure the earpieces is discon-
nected from the charging case
before removing the battery.
• Make sure the charging case is
disconnected from the USB
charging cable before removing the
battery.
Compliance with EMF
This product complies with all applica-
ble standards and regulations regarding
exposure to electromagnetic elds.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard
(box), polystyrene foam (buer) and
polyethylene (bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by a
specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and
old equipment.
Notice of compliance
The device complies with the FCC rules, Part
15. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference
received, including interference that may
cause undesired operation.
FCC rules
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference to
radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment o and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between equipment
and receiver
Connect the equipment into an outlet on a
circuit dierent from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment.
This transmitter must not be co-located or
operating in conjunction with any other
antenna or transmitter.
Canada:
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Develop-
ment Canada’s licence-exempt RSS(s).
Operation is subject to the following two
conditions: (1)This device may not cause
interference. (2)This device must accept any
interference, including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et
Développement économique Canada
applicables aux appareils radio exempts de
licence.
L’exploitation est autorisée aux deux
conditions suivantes : (1) L’appareil ne doit
pas produire de brouillage; (2) L’appareil doit
accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en
compromettre le fonctionnement.
CAN ICES-3(B)/NMB-3(B)
IC Radiation Exposure Statement:
This equipment complies with Canada
radiation exposure limits set forth for
uncontrolled environments.
This transmitter must not be co-located or
operating in conjunction with any other
antenna or transmitter.
Caution: The user is cautioned that changes
or modications not expressly approved by
the party responsible for compliance could
void the user's authority to operate the
equipment.
EN
8 Trademarks
The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Top Victory Investment Limited
is under license. Other trademarks and
trade names are those of their respec-
tive owners.
Bluetooth
Siri is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
Siri
Google and Google Logo are registered
trademarks of Google Inc.
Google
9 Frequently
asked
questions
My Bluetooth earpieces does not turn on.
The battery level is low. Charge the
earpieces.
I cannot pair my Bluetooth earpieces with
my Bluetooth device.
The Bluetooth is disabled. Enable the
Bluetooth feature on your Bluetooth
device and turn on the Bluetooth device
before you turn on the earpieces.
Pairing does not work.
• Put both earpieces into charging case.
• Make sure you have disabled the
Bluetooth function of any previously
connected Bluetooth devices.
• On your Bluetooth device, delete
“Philips TAT2205/TAT2235/TAT2245”
from the Bluetooth list.
• Pair your earpieces (see ‘Pair the
earpieces with your Bluetooth device
at the first time’ on page 6).
How to reset pairing.
Put both earpieces back to chargingcase.
Both earpieces ashes white led.
Press and hold both earpieces function
button for 4s,until earpieces ashes twice
white led .
The Bluetooth device cannot nd the
earpieces.
• The earpieces may be connected to a
previously paired device. Turn o the
connected device or move it out of
range.
• Pairing may have been reset or the
earpieces has been previously paired
with another device. Pair the earpieces
with the Bluetoot device again as
described in the user manual. (see
‘Pair the earpieces with your Bluetooth
device at the st time’ on page 6).
My Bluetooth earpieces is connected to a
Bluetooth stereo enabled mobile phone,
but music only plays on the mobile phone
speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through
the earpieces.
The audio quality is poor and crackling
noise can be heard.
• The Bluetooth device is out of range.
Reduce the distance between your
earpieces and Bluetooth device, or
remove obstacles between them.
• Charge your earpieces.
The audio quality is poor when streaming
from the mobile phone is very slow, or
audio streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but alos
supports A2DP and is BT4.0x (or higher)
compatible (see ‘Technical data’ on page
10).
14
I hear but cannot control music on my
Bluetooth device (e.g. play/pause/skip
forward/backward).
Make sure the Bluetooth audio source
supports AVRCP (see ‘Technical data’ on
page 10).
The volume level of the earpieces is toot
low.
Some Bluetooth devices cannot link the
volume level with the earpieces through
volume sync. In this case, you have to
adjust the volume on your Bluetooth
device independently to achieve an
appropriate volume level.
I cannot connect the earpieces to another
device, what do I do?
• make sure the Bluetooth function of
the previous paired device is turned
o.
• Repeat the pairing procedure on your
second device (see ‘Pair the earpieces
with your Bluetooth device at the
rst time’ on page 6).
I hear sound from only one earpiece.
• If you are in a call, it is normal that
sound comes from the right and left
earpiece.
• If you are listening to music but sound
only comes from one earpiece:
• The other earpiece may be out of
battery. For optimal performance,
charge both earpiece fully.
• The right and left earpieces are
disconnected from each other,
Turn o both earpiece rst. Then
put both earpieces back to
charging case for 5 seconds and
take them out. This will turn the
earpieces on and connect the two
earpieces. Reconnect the earpieces
to your Bluetooth device.
• The earpieces is connected to more
than one Bluetooth device. Switch
o the Bluetooth function of all
connected devices. Turn o both
earpieces. Put both earpieces back
to charging case for 5 seconds
and take them out. Reconnect the
earpieces to your Bluetooth device.
Note that the earpieces is desighed
for connecting to only one Blue
tooth device ath a time. When you
reconnect the earpieces to your
Bluetooth device, make sure the
Bluetooth function of any other
Previously paired/connected
devices are o.
• If the above solutions do not help,
factory reset the earpieces (see
‘Factory reset the earpieces’ on
page 9).
For further support, visit
www.philips.com/support.
15
Este equipamento não tem direito à proteção contra interferência prejudicial
e não pode causar interferência em sistemas devidamente autorizados.
Este produto está homologado pela ANATEL, de acordo com os
procedimentos regulamentados pela Resolução 242/2000, e atende aos
requisitos técnicas aplicados. Para maiores informações, consulte a site da
ANATEL: www.anatel.gov.br
Philips and Philips Shield Emblem are registered trademarks of Koninklijke
Philips N.V. and are used under license. This product has been
manufactured by and is sold under the responsibility of MMD Hong Kong
Limited is the warrantor in relation to this product.
UM_TAT2205_TAT2235_TAT2245_00_EN_V3.0