Philips TAT5505BK/00 User Manual
Displayed below is the user manual for TAT5505BK/00 by Philips which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
User manual
Register your product and get support at
www.philips.com/support
5000 Series
TAT5505
Headphones
1 Important safety instructions 2
Hearing Safety 2
General information 2
2 Your True wireless
earphones 3
What's in the box 3
Other devices 3
Overview of your True wireless
earphones 4
3 Get started 5
Charge the battery 5
Pair the earpieces with your
Bluetooth device for the st time 6
4 Use your headphones 7
Connect the earpieces to your
Bluetooth device 7
Control ANC (active noise
cancelation) 7
Manage your calls and music 8
LED indicator status 8
Voice Assistant 9
5 Reset the earpieces 10
6 Technical data 10
7 Notice 11
Declaration of conformity 11
Disposal of your old product
and battery 11
Remove the integrated battery 11
Compliance with EMF 12
Environmental information 12
Notice of compliance 12
8 Trademarks 14
9 Frequently asked questions 15
Contents
1 Important
safety
instructions
Hearing Safety
Danger
To avoid hearing damage, limit the time you
use headphones at high volume and set the
volume to a safe level. The louder the
volume, the shorter the safe listening time is.
Be sure to observe the following guide-
lines when using your headset.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your
hearing adapts.
• Do not turn up the volume so high
that you can't hear what's around
you.
• You should use caution or tempo-
rarily discontinue use in potentially
hazardous situations.
• Excessive sound pressure from
earphones and headphones can
cause hearing loss.
• Using headphones with both ears
covered while driving is not recom-
mended and may be illegal in some
areas while driving.
• For your safety, avoid distractions
from music or phone calls while in
trac or other potentially dangerous
environments.
General information
To avoid damage or malfunction:
Caution
Do not expose headphones to excessive heat
Do not drop your headphones.
Headphones shall not be exposed to dripping
, splashing water.
Do not allow your headphones to be
submerged in water.
Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft doth, if
necessary dampened with a minimum amount
of water or diluted mild soap, to clean the
product.
The integrated battery shall not be exposed to
excessive heat such as sunshine, re or the
like.
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
• Disposal of a battery into re or a hot oven, or
mechanically crushing or cutting of a battery,
can result in an explosion;
• Leaving a battery in an extremely high
temperature surrounding environment can
result in an explosion or the leakage of
ammable liquid or gas;
• A battery subjected to extremely low air
pressure that may result in an explosion or the
leakage of ammable liquid or gas.
About operating and storage temperatures
and humidity
• Store in a place where temperature is
between -20°C (-4°F) and 50°C (122 °F)
(up to 90% relative humidity.
• Operate in a place where temperature
is between 0°C (32°F) and 45°C (113 °F)
(up to 90% relative humidity.
• Battery life may be shorter in high or
low temperature conditions.
• Replacement of a battery with an
incorrect type that can defeat a
safeguard (for example, in the case of
some lithium battery types);
2 Your True
wireless
earphones
What's in the box
Philips True wireless earphones
Philips TAT5505
Replaceable rubber ear caps x 3 pairs
Quick start guide
Other devices
A mobile phone or device (e.g. note-
book, PDA, Bluetooth adapters, MP3
players etc) which supports Bluetooth
and is compatible to the headset (see
'Technical data' on page 8).
Congratulations on your purchase, and
welcome to Philips! To fully benet
from the support that Philips oers,
register your product at
www.philips.com/welcome.
With this Philips True wireless
earphones, you can:
• enjoy convenient wireless
handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.
USB-C charging cable (for charging only)
Global Warranty
Safety leaet
Overview of your True
wireless earphones
Microphone
Multi-function touch
LED indicator (Earpieces)
LED indicator (charging box)
USB-C charging slot
3 Get started
Charge the battery
Charging Box
Earpieces
Note
Before you use your earpieces for the rst
time, place the earpieces in the charging box
and charge the battery for 3 hours for
optimum battery capacity and lifetime.
Use only the original USB-C charging cable to
avoid any damage.
Finish your call before charging the earpieces,
as connecting the earpieces for charging will
power the earpieces o.
Connect one end of the USB cable into
the charging box, and another end into
the power source.
• Charging process is veried by the
blue LED light on the front panel.
• When the charging box is fully
charged, the blue light goes on.
• Charging process is veried by blue
LED light on the earpieces.
• When the earpieces is fully charged,
the blue light goes o.
Tip
Tip
The charging box serves as a portable backup
battery for charging the earpieces. When the
charging box is fully charged, it supports 3
times full recharge cycle for the earpieces.
Normally, a full charge takes 2 hours (for the
earpieces or charging box) by USB cable.
Place the earpieces in the charging box.
The earpieces start charging.
The charging box starts charging.
The LED on both earpieces ash
in white & blue alternately.
Pair the earpieces with
your Bluetooth device
for the st time
Open the top cover from charging
box.
Make sure that the headset is fully
charged and powered o.
Single earpiece (Mono mode)
Take either right or Left earpiece out
from charging box for Mono use. The
earpiece will power on automatically.
There will be a voice “Power on” from
earpiece.
Note
Note
After powering on, if the earpieces cannot nd
any previously connected Bluetooth device, it
will automatically switch to pairing mode.
Note
Take the second Earpiece from the charging
box and they will pair each other automatically.
The earpieces stores 4 device in the memory. If
you try to pair more than 4 devices, the earliest
paired device is replaced by the new one.
Pair the earpieces with
another Bluetooth device
The earpieces are now in
pairing mode and is ready to
pair with a Bluetooth device
(e.g. a mobile phone)
Turn on the Bluetooth function
of your Bluetooth device, select
Philips TAT5505.
Turn on the Bluetooth function of
your Bluetooth device.
Pair the earpieces with your
Bluetooth device. Refer to the user
manual of your Bluetooth device.
The following example shows you
how to pair the earpieces with
your Bluetooth device.
If you have another Bluetooth device
that you want to pair with the earpieces,
make sure the Bluetooth function in any
other previously paired or connected
devices are turned o.
Long touch over 5 seconds both left &
right side simultaneously with earpiece
on ear, release when Pairing voice
prompt is heard.
Enter the earpieces password
“0000” (4 zeros) if prompted. For
those Bluetooth devices featuring
Bluetooth 3.0 or higher, no need to
enter a password.
Philips TAT5505
Dierent ANC mode can be toggled via
double tap on the right earpiece.
• ANC function is auto active when
put into the ear.
• Touch the MFB button twice, it will
change to Awareness mode.
• Touch the MFB button twice again,
it will turn the ANC function o.
Tip
Note
The earpieces cannot connect to more than 1
device at the same time. If you have two paired
Bluetooth devices, only turn on the Bluetooth
function of the device that you want to connect.
If you turn on the Bluetooth function of your
Bluetooth device after turning on the earpieces,
you have to go to the Bluetooth menu of the
device and connect the earpieces to the device
manully.
Tip
By removing the earpiece, it will automatically
change to sleep mode. When put earpiece back,
it will return to active mode.
If the earpieces fails to connect to any
Bluetooth device within 5 minutes, it will turn o
automatically to save the battery life.
In some Bluetooth devices, connection may not
be automatic. In this case, you have to go to the
Bluetooth menu of your device and connect the
earpieces to the Bluetooth device manually.
The blue LED ashes.
The earpieces will search the
last connected Bluetooth device
and reconnect to it automatical-
ly. If the last connected device is
not available, the earpieces will
enter pairing mode.
4 Use your
earpieces
Turn on the Bluetooth function of
your Bluetooth device.
Open the top cover from charging
box.
Connect the earpieces to
your Bluetooth device
Task
ANC ON Right
earpiece
Right
earpiece
Double tap
Double tapAwareness
mode
ANC OFF Right
earpiece
Right
earpiece
Double tap
Tap and
hold
Attention
mode
Multi-
function
button
Operation
Control ANC (active noise
cancelation)
Enable ANC
ANC ON
Awareness
mode
ANC O
Task
Turn the
earpieces
on.
Earpiece
take out
from
charging
box to
power on
Earpiece
put back to
charging
box to
power o
Turn the
earpieces
o.
Power on/o
Multi-
function
button
Operation
Music control
Play or
pause music
Skip forward Right
earpiece
Triple taps
Adjust
volume +/-
Via mobile
phone
control
Right
earpiece
Single tap
Manage your calls and
music
Task Multi-
function
button
Operation
Headphones status Indicator
ANC mode is
toggled
The blue LED will
turn on.
ANC LED indicator status Call control
Pick up/
Switch caller
during a call
Hang up call
/Reject call
Right
earpiece
Tap and
hold
Right
earpiece
Double
taps
Task Multi-
function
button
Operation
LED indicator status
The earpieces are
connected to a
Bluetooth device.
The earpieces are
ready for pairing
The earpieces are
on but not
connected to a
Bluetooth device
Low battery level
(earpieces)
Blue LED blink 2x
every 5s
The blue & white
LED ash
alternately
White LED blink
every 1s
(auto turn o after
3min)
White LED blink
every 5s
Headphones
status
Indicator
Battery is fully
charged
(charging box).
Refer to Case
LED
Battery LED indicator on
Bluetooth device
It will show a battery indicator on
Bluetooth device after connected to
earpieces.
Task Button Operation
Left
earpiece
Trigger voice
(Siri/Google)
assistant
Tap and
hold 2
seconds
Voice Assistant
How to wear
Charging Box (4 blue
LED)
Charging Box
LED (USB on)
Indicator
Continue to lit as
long as USB is on
Tip
When USB is o, the LED is lit for 30s after case open
or closed
Charging Box
LED (USB o)
Indicator
5 Reset the
earpieces
6 Technical data
Note
Specications are subject to change without
notice.
Music time — ANC enabled: 4.5
hours | ANC disabled with Bluetooth:
5 hours
Talk time — ANC enabled: 4.5 hours |
ANC disabled: 5 hours
Standby time — 200 hours
Charging time: 2 hours
Lithium-ion battery 50 mAh on each
earpiece, Lithium-ion battery 410
mAh on charging box
Bluetooth version: 5.1
Compatible Bluetooth proles:
• HSP (Hands-Free Prole-HFP)
• A2DP (Advanced Audio Distri-
bution Prole)
• AVRCP (Audio Video Remote
Control Prole)
Supported audio codec: SBC
Frequency range: 2.402-2.480 GHz
Transmitter power: < 5 dBm
Operating range: Up to 10 meters (33
feet)
Auto power o
USB-C port for charging
Low battery warning: available
TAT5505
Tap & hold multi-function touch for
>25s on each earpiece individually.
Return earpieces to charging box &
close the lid.
Follow steps in “Use your earpiec-
es-Connect the earpieces to your
Bluetooth device.”
Pair the earpieces with your
Bluetooth device, select Philips
TAT5505.
5
6
7 Notice
Hereby, MMD Hong Kong Holding Limited
declares that this product is in compli-
ance with the essential requirements and
other relevant provisions of Directive
2014/53/EU. You can nd the Declaration
of Conformity on www.p4c.philips.com.
Declaration of conformity
Disposal of your old
product and battery
Your product is designed and manufac-
tured with high quality materials and
components, which can be recycled and
reused.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This symbol means that the product
contains a built-in rechargeable battery
covered by European Directive
2013/56/EU which cannot be disposed
of with normal household waste. We
strongly advise you to take your product
to an ocial collection point or a Philips
service centre to have a professional
remove the rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and never
dispose of the product and rechargeable
batteries with normal household waste.
Correct disposal of old products and
rechargeable batteries helps prevent
negative consequences for the environ-
ment and human health.
Remove the integrated battery
If there is no collection/recycling system
for electronic products in your country,
you can protect the environment by
removing and recycling the battery
before disposing the headphones.
• Make sure the earpieces is discon-
nected from the charging box
before removing the battery.
• Make sure the charging box is
disconnected from the USB
charging cable before removing the
battery.
Compliance with EMF
This product complies with all applica-
ble standards and regulations regarding
exposure to electromagnetic elds.
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials which
can be recycled and reused if disassem-
bled by a specialized company. Please
observe the local regulations regarding
the disposal of packaging materials,
exhausted batteries and old equipment.
Notice of compliance
The device complies with the FCC rules,
Part 15. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
FCC rules
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to part
15 of the FCC Rules. These limits are
designed to provide reasonable protec-
tion against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment
o and on, the user is encouraged to try
to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between
equipment and receiver
Connect the equipment into an outlet
on a circuit dierent from that to which
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
Canada:
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Develop-
ment Canada’s licence-exempt RSS(s).
Operation is subject to the following two
conditions: (1)This device may not cause
interference. (2)This device must accept any
interference, including interference that may
cause undesired operation of the device.
Caution:
The user is cautioned that
changes or modications not expressly
approved by the party responsible for
compliance could void the user's
authority to operate the equipment.
IC Radiation Exposure Statement:
This equipment complies with Canada
radiation exposure limits set forth for
uncontrolled environments.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et
Développement économique Canada
applicables aux appareils radio exempts de
licence.
L’exploitation est autorisée aux deux
conditions suivantes : (1) L’appareil ne doit
pas produire de brouillage; (2) L’appareil doit
accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en
compromettre le fonctionnement.
CAN ICES-3(B)/NMB-3(B)
8 Trademarks
The Bluetooth® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by MMD Hong Kong Holding
Limited is under license. Other trade-
marks and trade names are those of
their respective owners.
Bluetooth
Siri is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
Siri
Google and Google Play are trademarks
of Google LLC.
Google
9 Frequently
asked
questions
My Bluetooth headset does not turn on.
The battery level is low. Charge the
headset.
I cannot pair my Bluetooth headset with
my Bluetooth device.
The Bluetooth is disabled. Enable the
Bluetooth feature on your Bluetooth
device and turn on the Bluetooth device
before you turn on the headset.
Pairing does not work.
• Put both earpieces into charging box.
• Make sure you have disabled the
Bluetooth function of any previously
connected Bluetooth devices.
• On your Bluetooth device, delete
“Philips TAT5505” from the Bluetooth
list.
• Pair your headset (see ‘Pair the
headset with your Bluetooth device
at the rst time’ on page 6).
The Bluetooth device cannot nd the
headset.
• The headset may be connected to a
previously paired device. Turn o the
connected device or move it out of
range.
• Pairing may have been reset or the
headset has been previously paired
with another device. Pair the headset
with the Bluetoot device again as
described in the user manual. (see
‘Pair the headset with your Bluetooth
device at the st time’ on page 6).
My Bluetooth headset is connected to a
Bluetooth stereo enabled mobile phone,
but music only plays on the mobile phone
speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through
the headset.
The audio quality is poor and crackling
noise can be heard.
• The Bluetooth device is out of range.
Reduce the distance between your
headset and Bluetooth device, or
remove obstacles between them.
• Charge your headset.
The audio quality is poor when streaming
from the mobile phone is very slow, or
audio streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but alos
supports A2DP and is BT4.0x (or higher)
compatible (see ‘Technical data’ on page
10).
APP DOWNLOAD
Scan the QR code/press 'Download'
button or search 'Philips Headphones' in
Apple App Store or Google Play to
download App.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license. This product has been
manufactured by and is sold under the responsibility of MMD Hong Kong
Holding Limited or one of its aliates, and MMD Hong Kong Holding
Limited is the warrantor in relation to this product.
UM_TAT5505_00_EN_V1.0