Philips TAX7207/10 User Manual
Displayed below is the user manual for TAX7207/10 by Philips which is a product in the Portable Speakers category. This manual has pages.
Related Manuals
Party Speaker
7000 Series
TAX7207
User manual
Register your product and get support at
www.philips.com/support
2 3ENEN
Contents
1 Important safety instructions 3
Safety 3
Care for your product 4
Care of the environment 4
Declaration of conformity 4
Help and support 4
Hearing safety 5
Built-in battery care 5
Trademarks 5
2 Your party speaker 7
What’s in the box 7
Party speaker 8
3 Get started 9
Connect to power 9
Turn On and O 10
Volume control 10
DBB control 10
Charge the built-in battery 10
Change light eect 11
Play from Bluetooth devices 12
Pairing for stereo mode (TWS) 13
PartyLink mode 14
Play audio through USB 15
Listen to an external device 16
Sing through microphone 16
Factory reset 16
Update rmware via USB 17
Pole-mounting your party speaker 17
4 Product specications 18
5 Troubleshooting 19
2 3ENEN
1 Important
safety
instructions
Read and understand all instructions
before you use your product. If damage
is caused by failure to follow instructions,
the warranty does not apply.
Safety
Know these safety symbols
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This is CLASS II apparatus with
double insulation, and no
protective earth provided.
AC voltage
Use only the power supplies listed
in the user manual.
WARNING!
Warning: Risk of electric shock!
The exclamatory mark is intended
to alert the user of the presence of
important operating instructions.
Risk of electric shock or re!
• Before you make or change any
connections, make sure that all
devices are disconnected from the
power outlet.
• Never expose the product and
accessories to rain or water. Never
place liquid containers, such as vases,
near the product. If liquids are spilt
on or into the product, disconnect it
from the power outlet immediately.
Contact Consumer Care to have the
product checked before use.
• Never place the product and accessories
near naked ames or other heat sources,
including direct sunlight.
• Never insert objects into the
ventilation slots or other openings
on the product.
• Where the mains plug or an
appliance coupler is used as the
disconnect device, the disconnect
device shall remain readily operable.
• Disconnect the product from the
power outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
• Use the product in tropical and/or
moderate climates.
Risk of short circuit or re!
• For identication and supply ratings,
see the type plate at the back or
bottom of the product.
• Before you connect the product to
the power outlet, ensure that the
power voltage matches the value
printed on the back or bottom of the
product. Never connect the product
to the power outlet if the voltage is
dierent.
Risk of injury or damage to this
product!
• For wall mounting, this product must
be securely attached to the wall in
accordance with the installation
instructions. Use only the supplied
wall mount bracket (if available).
Improper wall mounting may result
in accident, injury or damage. If you
have any query, contact Consumer
Care in your country.
• Never place the product or any
objects on power cords or on other
electrical equipment.
4 5ENEN
Inform yourself about the local separate
collection system for electrical and
electronic products and batteries.
Follow local rules and never dispose of
the product and batteries with normal
household waste. Correct disposal
of old products and batteries helps
prevent negative consequences for the
environment and human health.
Declaration of conformity
This product complies with the radio
interference requirements of the
European community.
Hereby, MMD Hong Kong Holding
Limited declares that the product
is in compliance with the essential
requirements and other relevant
provisions of RED Directive 2014/53/EU
and UK Radio Equipment Regulations
SI 2017 No 1206. You can nd the
Declaration of Conformity on www.
philips.com/support.
Help and support
For extensive online support, visit www.
philips.com/support to:
• download the user manual and the
quick start guide
• watch video tutorials (available only
for selected models)
• nd answers to frequently answered
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website
to select your language, and then enter
your product model number.
Alternatively, you can contact Consumer
Care in your country. Before you contact,
note down the model number and serial
number of your product. You can nd
this information on the back or bottom
of your product.
• If the product is transported in
temperatures below 5°C, unpack
the product and wait until its
temperature matches room
temperature before connecting it to
the power outlet.
• Parts of this product can be made
of glass. Handle with care to avoid
injury and damage.
Risk of overheating!
• Never install this product in a
conned space. Always leave a
space of at least four inches around
the product for ventilation. Ensure
curtains or other objects never cover
the ventilation slots on the product.
Note
• The rating label is pasted on the bottom or back
of the equipment.
Care for your product
Use only microber cloth to clean the
product.
Care of the environment
Disposal of your old product and
battery
Your product is designed and
manufactured with high quality
materials and components, which
can be recycled and reused.
This symbol on a product means
that the product is covered by
European Directive 2012/19/EU.
This symbol means that the product
contains batteries covered by
European Directive 2013/56/EU
which cannot be disposed of with
normal household waste.
4 5ENEN
Hearing safety
Listen at a moderate volume
• Using headphones at a high volume
can impair your hearing. This product
can produce sounds in decibel ranges
that may cause hearing loss for a
normal person, even for exposure
less than a minute. The higher
decibel ranges are oered for those
that may have already experienced
some hearing loss.
• Sound can be deceiving. Over time
your hearing ‘comfort level’ adapts
to higher volumes of sound. So after
prolonged listening, what sounds
‘normal’ can actually be loud and
harmful to your hearing. To guard
against this, set your volume to a
safe level before your hearing adapts
and leave it there.
To establish a safe volume level
• Set your volume control at a low
setting.
• Slowly increase the sound until you
can hear it comfortably and clearly
without distortion.
Listen for reasonable periods of time
• Prolonged exposure to sound, even
at normally safe levels, can also cause
hearing loss.
• Be sure to use your equipment
reasonably and take appropriate
breaks.
• Be sure to observe the following
guidelines when using your
headphones.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
as your hearing adapts.
• Do not turn up the volume so high
that you can’t hear what’s around you.
• You should use caution or
temporarily discontinue use in
potentially hazardous situations.
Built-in battery care
• The battery can be charged and
discharged hundreds of times, but
will eventually wear out.
• If left unused, a fully charged battery
will lose its charge over time.
• Leaving the product in hot or cold
places, such as in a closed car in the
summer and winter conditions, will
reduce the capacity and lifetime of
the battery.
• Always try to keep your device in
a cool, moisture-free environment
that’s less than 32°C. A product with
a hot or cold battery may not work
temporarily, even when the battery is
fully charged. Battery performance is
particularly limited in temperatures
well below freezing.
Trademarks
The Bluetooth® word mark and logos
are registered trademarks owned
by Bluetooth SIG, Inc. and any use
of such marks by MMD Hong Kong
Holding Limited is under license. Other
trademarks and trade names are those of
their respective owners.
67ENEN
IC-Canada:
CAN ICES-003(B)/NMB-003(B)
This device contains licence-exempt
transmitter(s) / receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the
following two conditions:
1 This device may not cause
interference.
2 This device must accept any
interference, including interference
that may cause undesired operation
of the device.
Avis d’Industrie Canada:
CAN ICES-003(B)/NMB-003(B)
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts
de licence. L’exploitation est autorisée
aux deux conditions suivantes :
1 L’appareil ne doit pas produire de
brouillage ;
2 L’appareil doit accepter tout
brouillage radioélectrique
subi, même si le brouillage est
susceptible d’en compromettre le
fonctionnement.
FCC information
NOTE: This equipment has been tested
and found to comply with the limits
for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio
or television reception, which can be
determined by turning the equipment
o and on, the user is encouraged to
try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an
outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced
radio / TV technician for help.
FCC&IC Warning:
• This equipment should be installed
and operated with minimum
distance 20cm between the radiator
and your body.
• Changes or modications to this unit
not expressly approved by the party
responsible for compliance could
void the user’s authority to operate
the equipment.
67ENEN
2 Your party
speaker
Congratulations on your purchase, and
welcome to Philips! To fully benet from
the support that Philips oers, register your
party speaker at www.philips.com/support.
What’s in the box
Check and identify the items in the
package:
Party Speaker x 1
Power Cord * x 1
• Power cord quantity and plug type
vary by regions.
TAX7207/93 TAX7207/37 TAX7207/10 TAX7207/98 TAX7207/94
for China
CCCVDEBS
for Europe/UK
UL
for US/Canada
VDEBSSAA
for Asia
BIS
for India
TAX7207/70
SNI
for Indonesia
TAX7207/67
TISI
for Thailand
Headph ones
Headph ones
hon
Headph ones
Series
Series
Series
CTN
Safety Information
Quick Start Guide x 1
Headph ones
Headph ones
hon
Headph ones
Series
Series
Series
CTN
Safety Information
Warranty Card x 1
Headph ones
Headph ones
hon
Headph ones
Series
Series
Series
CTN
Safety Information
Safety Sheet x 1
• Images, illustrations and drawings
shown on this user manual are for
reference only, actual product may
vary in appearance.
8 9ENEN
Party speaker
This section includes an overview of the
party speaker.
67
1 2 3 4 5
20
8
14 15 16 17 18 19
910 11 12 13
a (Light) touch key
• Press to change speaker light
mode.
• Press and hold for 3 seconds to
change speaker light brightness.
b DBB touch key
BASS eect setup.
c +/－ (Volume) touch key
Increase/Decrease the volume.
d (Play/Pause) touch key
• Start, pause or resume play.
• Press and hold to skip to next
track.
e (Standby-On) touch key
• Press and hold for 3 seconds to
switch on/o the unit.
• Press to check battery level in
power on status.
f Speaker light
67
1 2 3 4 5
20
8
14 15 16 17 18 19
910 11 12 13
Button Status
Short press
Light mode 1
Light o
g LED indicator
• Battery level indicator
• Function status
LED Function Color
LED1 DBB Solid yellow
LED2 Standby Solid red
Vocal fader Solid white
LED3
Bluetooth Blink or solid blue
TWS pairing Blink blue-white
PartyLink connected Solid white
LED4 Voice changer Solid green
PartyLink pairing Blink green-white
h Vocal fader button
Press repeatedly to switch between
vocal fader on and vocal fader o.
8 9ENEN
i Voice changer button
Press repeatedly to switch among
dierent voice tones: Woman voice/
Man voice/Children voice/Normal eect.
j PartyLink button
Press to enter PartyLink pairing
mode.
k TWS pair button
• Press to enter True Wireless
Stereo (TWS) pairing mode.
• It work only when you have two
identical speakers.
l Bluetooth / pair button
• Switch to Bluetooth mode.
• Press and hold to activate the
pairing function in Bluetooth
mode or disconnect the existing
paired Bluetooth device.
m Mic1 in / Mic2 in socket
Connect a microphone (not supplied)
into the Mic1 in / Mic2 in socket on
the unit.
n Mic1 vol +/－ Knob
Adjust microphone volume.
o Mic2 vol +/－ Knob
Adjust microphone volume.
p Echo +/－ Knob
Adjust the microphone echo level.
q USB (5V, 0.5A) socket
• Insert the USB device to play music.
• Upgrade software of this product.
r Audio in socket
Audio input from, for example, an
MP3 player (3.5mm socket).
s Audio out socket
Connect an audio cable (not
supplied) to the Audio out socket on
the unit and the audio in socket of
the external device, and the unit will
output audio automatically to the
external device.
t AC in~ socket
Connect to the power supply.
3 Get started
When you use this unit for the rst time
or unused for long periods of time,
recharge the battery fully.
Note
• For identication and supply ratings, see the
type plate at the back or bottom of the product.
• Before you make or change any connections,
make sure that all devices are disconnected
from the power outlet.
Connect to power
WARNING!
• Risk of product damage! Make sure that the
power supply voltage corresponds to the
voltage printed on the back or the underside of
the product.
• Risk of electric shock! When you unplug the
power cord, always pull the plug from the
socket. Never pull the cord.
• Before connecting the AC power cord, ensure
you have completed all other connections.
Connect the mains cable to the AC in~
socket of the party speaker and then into
a mains socket.
AC in ~
or
or
Power cord quantity and plug type vary
by regions.
10 11ENEN
Turn On and O
Press and hold touch key for 3 seconds
to switch on/o the unit.
Note
• The speaker will turn o automatically after
15 minutes without user operations and music
playback.
• In case of no response of button or function
error, you can press and hold Vocal fader and
buttons for 10 seconds to force shutdown, then
turn on the unit again to be used normally.
Volume control
Press +/－ touch key to increase or
decrease volume level.
Tip
• While adjusting the volume, the white speaker
light will move up or down for 3 seconds.
• When the volume meets the maximum level,
the white speaker light will fully turn on for 3
seconds.
• When the volume meets the minimum level, the
white speaker light will turn o for 3 seconds.
DBB control
Short press DBB touch key to switch the
DBB (bass) level.
Function LED1 (Yellow)
DBB1 LED1 ash once then solid
DBB2 LED1 ash twice then solid
DBB o LED1 o
Charge the built-in
battery
Plug the AC power cord to charge the
built-in battery. The battery indicators
blink in dierent manners to indicate the
charging status.
Note
• The four indicators on the unit will go out in 15
seconds after the battery is fully charged.
20%
100
%
50%
80%
100
%
20%
Low Battery
50%
80%
100
%
10 11ENEN
Check the battery level
• The speaker is designed with a
smart battery check feature for your
convenience.
• When the speaker is not in charging,
press touch key to display the
battery level on the LED indicators.
Note
• When the battery level is low, all battery LED
indicators will blink simultaneously and a
prompt tone is heard.
20%
100
%
50%
80%
100
%
20%
Low Battery
50%
80%
100
%
Change light eect
Turn speaker light on or o
In power on mode, press (Light) touch
key repeatedly to switch among dierent
light modes of speaker light.
Light mode 1
Light mode 2
Light off
3 sec
Change brightness
Press and hold (Light) touch key
for 3 seconds to change speaker light
brightness.
12 13ENEN
Play from Bluetooth
devices
The product can stream music from your
Bluetooth device to the system through
Bluetooth.
Note
• A Bluetooth device which supports Bluetooth
prole A2DP, AVRCP and with Bluetooth version
as 5.0 + EDR.
• The maximum operational range between
the party speaker and a Bluetooth device is
approximately 30 meters.
• The player will also be disconnected when your
device is moved beyond the operational range.
• Compatibility with all Bluetooth devices is not
guaranteed.
LED3 State Status
Blinking blue • Ready for Pairing
• Reconnecting the last
connected device
Solid blue Connected
1 Press the button to switch the
party speaker to Bluetooth mode.
» The LED indicator (LED3) and
speaker light will blink blue.
2 On the Bluetooth device, switch
on Bluetooth, search for and select
Philips TAX7207 to start connection.
» During connection, the LED
indicator (LED3) and speaker light
will blink blue.
3 Wait until you hear voice prompt
from the party speaker.
» When the speaker is connected,
the LED indicator (LED3) and
speaker light turn solid blue.
4 Select and play audio les or music
on your Bluetooth device.
Key Action
Short press Start, pause or resume play.
Long press Skip to the next track.
5 To exit Bluetooth, you can:
• Switch the unit to another source.
• Disable the function from your
Bluetooth device. Or place your
Bluetooth device out of the
maximum operational range.
The Bluetooth device will be
disconnected from the unit after
the voice prompt.
• Press and hold button until the
LED indicator blinks blue.
Note
• To disconnect a device, press and hold for
3 seconds until the LED indicator blinks blue
quickly.
• When you turn on the speaker, it always
automatically tries to reconnect the last
successfully connected device.
• Before connecting another Bluetooth device,
disconnect the current device rstly.
• When the Bluetooth device is beyond the valid
Bluetooth distance, the unit will disconnect
automatically from the device.
• Press and hold button on the unit for 8
seconds to disconnect the current device and
clear out the Bluetooth pairing information.
Multi-point control
The product support multi-point feature,
and can connect two Bluetooth device at
same time.
• There is audio prompt when the
second Bluetooth device connect the
party speaker.
• When the rst Bluetooth device
pause or disconnected, the second
Bluetooth device can stream its
audio to party speaker.
• Incoming call has priority over music
playback regardless from rst or
second devices.
Note
• Under TWS and PartyLink mode, multi-point
control is not supported.
12 13ENEN
Pairing for stereo mode
(TWS)
Two speakers can pair with each other
for stereo sound.
Note
• TWS is worked only if there are two identical
party speakers (Philips TAX7207).
Select master speaker manually
1 Press and hold key for 3 seconds to
power on both speakers and enter to
Bluetooth pairing mode.
» The LED indicator (LED3) on both
speakers blink blue.
2 Select one speaker as master and
connect to Bluetooth.
» LED3 on master speaker turns
solid blue once Bluetooth is
connected.
3 Press and hold (TWS) button on
both speakers for 3 seconds to enter
stereo pairing mode (TWS).
» LED3 blinks blue and white
alternatively on both speakers
4 When TWS is connected, you will
hear a voice prompt.
» LED3 turns solid blue on both
speakers.
5 To exit TWS, press and hold (TWS)
button on either speaker.
Select master speaker automatically
1 Press and hold touch key for 3
seconds to power on both speakers.
» The LED indicator (LED3) on both
speakers blink blue.
2 Press and hold TWS button on
both speakers for 3 seconds to enter
stereo pairing mode.
» The rst speaker entered TWS
mode is master and LED3 on
master speaker turns sold blue.
» The volume level, play/pause
state, light mode in slave speaker
will sync from master speaker
after TWS connected.
3 To exit TWS, press and hold (TWS)
button on either speaker.
Note
• During TWS pairing mode, both master and
slave speaker will return to previous state
automatically after 1 minute without user
operations or TWS pairing is not successful.
TWS playback operation
When TWS is connected, the slave
speakers will synchronize from master
speaker of below functions.
• Light eect
• Volume level
• Play/pause
• DBB (bass) level
Key & Operate Action
Press key on
either speaker
Play/pause the
music on both
speakers
Press VOL +/－ key
on either speaker
Increase or
decrease volume
on both speakers
Press DBB key on
either speaker
Change DBB setting
on both speakers
Press and hold key
on either speaker
for 3 seconds
Power o both
speakers
Press and hold key
on either speaker
for 3 seconds in
standby state
Power on selected
speaker and enter
TWS reconnection
Press key on
either speaker
Change light mode
in both speakers
14 15ENEN
Key & Operate Action
Press and hold key
on either speaker
for 3 seconds
Change brightness
in all speakers
Press and hold
button on either
speaker for 3 seconds
Exit TWS mode
PartyLink mode
The speaker can connect up to 50 party
speakers together and play audio at the
same time.
Enter PartyLink mode
1 Press and hold key for 3 seconds to
power on party speakers and enter
to Bluetooth pairing mode.
» The LED indicator (LED3) on both
speakers blink blue.
2 Select one speaker as master and
connect to Bluetooth.
» LED3 on master speaker turns
solid blue once Bluetooth is
connected.
3 Press and hold PartyLink button on
all speakers for 3 seconds to enter
PartyLink pairing mode.
» LED4 blinks green and white
alternatively on all speakers.
4 When PartyLink is connected, you
will hear a voice prompt.
» LED3 on slave speakers turns solid
white.
» LED4 remains blinking green and
white alternatively on master
speaker.
» Volume level, play/pause state,
light mode in slave speakers will
sync from master speaker after
PartyLink connected.
5 Press and hold PartyLink button on
master speaker. All speakers will exit
PartyLink mode.
Note
• During PartyLink pairing mode, slave speaker
will return to previous state automatically after
1 minute without user operations or PartyLink
pairing is not successful.
• No timeout on master speaker.
PartyLink between TAX7207 and
TAX4207
You can connect TAX7207 with another
party speaker TAX4207, both models
have PartyLink function.
When PartyLink is connected, the slave
speakers will synchronize from master
speaker of below functions.
• Volume level
• Play/pause
• DBB (bass) level
PartyLink playback operation
When PartyLink is connected, the slave
speakers will synchronize from master
speaker of below functions.
• Light eect
• Volume level
• Play/pause
• DBB (bass) level
14 15ENEN
Key & Operate Action
Press key on
master speaker
Play/pause the music
on all connected
speakers
Press VOL +/－
key on master
speaker
Increase or decrease
volume on all
connected speakers
Press DBB key
on master
speaker
Change DBB setting on
all speakers
Press and hold
power key on
master speaker
for 3 seconds
Power o master
speaker, all slave
speakers will exit party
link mode
Press and hold
key on selected
slave speaker for
3 seconds
Power o selected
slave speaker, there
is no eect on master
speaker and other slave
speakers
Press and
hold key
on selected
speaker in
standby state
Power on selected
speaker and pressing
PartyLink key again to
enter PartyLink mode
Press key on
master speaker
Change light mode in
all connected speakers
Press key on
slave speakers
No change light
mode in all connected
speakers
Press and hold
key on master
speaker for 3
seconds
Change brightness in
all speakers
Press PartyLink
button on
selected slave
speaker
Disconnect selected
slave speaker from
master speaker
Press and hold
PartyLink
button on
master speaker
for 3 seconds
Disconnect all speakers
and exit PartyLink
mode
Play audio through USB
Enjoy audio on a USB storage device,
such as an MP3 player and USB ash
memory, etc.
Note
• Make sure that the USB device contains
playable audio contents in supported formats.
Supported formats: MP3, WAV, WMA, FLAC.
FLAC format audio only supports not over 16
bit rate.
• The unit supports max 128G USB and le format
FAT16/FAT32/exFAT.
• Support a USB port: 5V 0.5A.
1 Insert the USB device.
» The unit will switch to the USB
mode and play automatically.
Key Action
Short press Start, pause or resume play.
Long press Skip to the next track.
16 17ENEN
Listen to an external
device
With this product, you can listen to an
external audio device such as an MP3 player.
Play from an MP3 player
1 Connect an audio input cable (not
supplied) with a 3.5mm connector
on both ends to:
• The Audio in socket on the unit.
• The headphone socket on the
MP3 player.
Headphone
(3.5mm)
AUDIO OUT
Audio in
» The unit switches to the Audio in
mode automatically.
2 Play audio on the MP3 player (refer
to its user manual).
Audio out
This unit has a Audio out socket. You can
output the analog stereo audio signals to
external devices such as an active speaker.
Connect an audio cable (not supplied)
to the Audio out socket on the unit
and the audio in socket of the external
device, and the unit will output audio
automatically to the external device.
Sing through microphone
Adjust microphone volume
Connect a microphone (not supplied)
into the Mic in socket of the unit, and
adjust the microphone volume by
turning the Mic vol knob.
Now, enjoy the karaoke singing!
Adjust echo
Adjust the microphone echo level to your
desired level by turning the Echo knob.
Vocal fader
Press the Vocal fader button to switch
between vocal fader on and vocal fader
o.
Voice changer
Press the Voice changer button on the
panel to switch among dierent voice
tones: Woman voice / Man voice /
Children voice / Normal eect.
Factory reset
Reset device to default setting.
1 Turn on the party speaker, press
and hold + and buttons for 10
seconds.
» Battery capacity LEDs ash three
times.
» The party speaker is reset and
enters standby mode.
16 17ENEN
Update rmware via USB
1 Check if there is the latest rmware
version on www.philips.com/support.
Search for your model and click on
“Software and drivers”.
Red
1
2
3
Software update les
8sec
2 Copy the software update les into
USB ash drive, insert USB ash drive
on the unit.
3 Press and hold DBB key for 8 seconds
in power on state with power cable
plug.
LED2 (Red) Status
Slow blinking
Fast blinking
Enter upgrade mode
Upgrade start
LED o Upgrade nished and
restart
Pole-mounting your
party speaker
1 Remove the cover from the bottom
of the party speaker (please keep the
cover).
2 Lift the party speaker to a speaker
tripod (sold separately).
3 Adjust the speaker tripod to the
appropriate height.
2
3
1
Bottom View
18 19ENEN
4 Product
specifications
Note
• Specications and design are subject to change
without notice.
Amplier
AC output power (RMS) 80 W
AC output power
(maximum) 160 W
Battery output power 30 W
Frequency response 40Hz-20KHz,
±3dB
Signal to noise ratio ≥ 65 dBA
Total harmonic distortion < 10%
Speaker
Speaker impedance 4 ohm + 8 ohm x 2
Sensitivity 91 dB ±3dB/m/W
Bluetooth
Bluetooth version V 5.0
Bluetooth
frequency band
2.402 GHz ~ 2.480
GHz ISM Band
Transmitter power ≤10dBm
Bluetooth range 30 m (free space)
Streaming format: AAC, SBC, music
streaming (A2DP), Playback/volume control:
AVRCP Multipoint (Multipair) support
USB
USB direct version 2.0 Full Speed
USB output 5V, 0.5A
Extension Codec Sample Rate Bitrate
.mp3
MPEG 1
Layer 1 16 ~ 48 kHz 32 ~ 448 kbps
MPEG 1
Layer 2 16 ~ 48 kHz 8 ~ 384 kbps
MPEG 1
Layer 3 16 ~ 48 kHz 8 ~ 320 kbps
MPEG 2 /
MPEG 2.5
Layer 1
16 ~ 48 kHz 8 ~ 256 kbps
MPEG 2 /
MPEG 2.5
Layer 2
16 ~ 48 kHz 8 ~160 kbps
MPEG 2/
MPEG 2.5
Layer 3
16 ~ 48 kHz 8 ~ 160 kbps
.wav WAV 16 ~ 48 kHz Up to 1536
kbps
.wma WMA 8 ~ 48 kHz 5 ~ 320 kbps
.ac FLAC Up to 48 kHz /
16 bit
Battery
Battery capacity 14.4V, 2600mAh
(Built in rechargeable)
Battery life 12 hrs
Battery charge time 6.5 hrs
General information
AC power 100-240V~
50/60Hz, 35W
Eco standby fewer
consumption ≤ 0.5W
Dimensions
(WxHxD) 300x310x300 mm
Weight 7.5 kg
Operating
Temperature 0°C - 45°C
18 19ENEN
5 Troubleshooting
Note
• Never remove the casing of the product.
To keep the Warranty valid, never try to
repair the system yourself.
If you encounter problems when using
this unit, check the following points
before requesting service. If the problem
remains unsolved, go to the Philips
website (www.philips.com/support).
When you contact Philips, ensure that
your unit is nearby and the model
number and serial number are available.
No power
• Ensure that the unit is fully charged
or connected with a power source.
• Ensure that all the required cables
are securely connected.
• Ensure that the unit is switched on.
• To save power, the unit switches to
standby automatically 15 minutes
after a play reaches the end and no
control is operated.
No sound
• Adjust the volume.
• Check the sound input source.
No response of button or function
error
• Press and hold Vocal fader and
buttons for 10 seconds to force
shutdown, then turn on the unit
again to be used normally.
Cannot display some les in USB
device
• The number of folders or les in the
USB device has exceeded a certain
limit. This phenomenon is not a
malfunction.
• The formats of these les are not
supported.
USB device not supported
• The USB device is incompatible with
the unit. Try another one.
About Bluetooth device
The audio quality is poor after connection
with a Bluetooth-enabled device
• The Bluetooth reception is poor.
Move the device closer to this
product or remove any obstacle
between them.
Cannot connect with the device
• The Bluetooth function of the device
is not enabled. Refer to the user
manual of the device for how to
enable the function.
• This product is already connected
with another Bluetooth-enabled
device. Disconnect that device and
then try again.
The paired device connects and
disconnects constantly
• The Bluetooth reception is poor.
Move the device closer to this
product or remove any obstacle
between them.
• For some devices, Bluetooth
connection may be deactivated
automatically as a power-saving
feature. This does not indicate any
malfunction of this product.
Specications are subject to change without notice. Please visit
www.Philips.com/support for the latest updates and documents.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license.
This product has been manufactured by and is sold under the
responsibility of MMD Hong Kong Holding Limited. or one of its aliates,
and MMD Hong Kong Holding Limited. is the warrantor in relation to this
product.
TAX7207RE_UM_EN_V1.0_20220217