RAM Mounts RAM-B-360U User Manual
Displayed below is the user manual for RAM-B-360U by RAM Mounts which is a product in the Mounting Kits category. This manual has pages.
Related Manuals
RAM® TWIST AND TILT™ BASE ASSEMBLY GUIDE (SIDE A)
OPTION 1 - MIRROR RELOCATION
PLACE (N) TOOTH LOCK WASHER OVER THREAD, FOLLOWED BY (C) STAND-OFF, AND ANOTHER
(N) WASHER. EXPOSE FEMALE THREADED HOLE ON MOTORCYCLE AND USE (G or H) SCREW,
DEPENDING ON THREAD PITCH. MIRROR WILL ATTACH TO THE (C) MIRROR STAND-OFF
BRACKET USING (J or K) NUT, DEPENDING ON THREAD PITCH OF MIRROR. PLACE ONE (N)
TOOTH LOCK WASHER BETWEEN MIRROR AND (C) STAND-OFF BRACKET AND TIGHTEN.
TOOLS REQUIRED
4MM HEX DRIVE WRENCH
6MM HEX DRIVE WRENCH
8MM HEX DRIVE WRENCH
A
C
D
E
GH
F
PARTS INDEX
A. RAM TOP CLEVIS WITH BALL (QTY. 1)
B. RAM CLEVIS BASE WITH HOLE FOR BOLT (QTY. 1)
C. MIRROR STAND-OFF BRACKET (QTY. 1)
D. O-RING (QTY. 2)
E. #10-24 X 1” SOCKET HEAD SCREW (QTY. 1)
F. #10-24 NYLOCK NUT (QTY. 1)
G. M10 X 1.25 X 40MM SOCKET HEAD CAP SCREW (QTY. 1)
H. M8 X1.25 X 40MM SOCKET HEAD CAP SCREW (QTY. 1)
J. M10 X 1.25 THIN HEX NUT (QTY. 2)
K. M8 X 1.25 THIN HEX NUT (QTY. 2)
L. M10 X 1.25 X 20MM SOCKET HEAD CAP SCREW (QTY. 1)
M. M8 X 1.25 X 20MM SOCKET HEAD CAP SCREW (QTY. 1)
N. M10 TOOTH LOCK WASHER (QTY. 3)
B
J
K
LM
N
STEP 1:
LOCATE THREADED FEMALE HOLE ON YOUR MOTORCYCLE AND VERIFY THE APPROPRIATE THREAD PITCH BY CAREFULLY THREADING ONE OF (G, H, L or M) SCREWS
PROVIDED. THE LENGTH OF THE CORRECT SCREW WILL DEPEND ON WHICH OF THE TWO OPTIONS YOU SELECT BELOW. PLACE CORRECT SCREW THROUGH
CENTER OPENING OF (B) CLEVIS BASE.
OPTION 2 - NO MIRROR RELOCATION
PLACE (N) TOOTH LOCK WASHER OVER THREAD. USE (L or M) SCREW TO
ATTACH ASSEMBLY TO MOTORCYCLE. (C) STAND-OFF WILL NOT BE USED.
N
L or M
OPTION 2
OPTION 1
N
C
N
N
G or H
J or K
B
B
RMR-INS-B-360
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
RAM® TWIST AND TILT™ BASE ASSEMBLY GUIDE (SIDE A)
OPTION 1 - MIRROR RELOCATION
PLACE (N) TOOTH LOCK WASHER OVER THREAD, FOLLOWED BY (C) STAND-OFF, AND ANOTHER
(N) WASHER. EXPOSE FEMALE THREADED HOLE ON MOTORCYCLE AND USE (G or H) SCREW,
DEPENDING ON THREAD PITCH. MIRROR WILL ATTACH TO THE (C) MIRROR STAND-OFF
BRACKET USING (J or K) NUT, DEPENDING ON THREAD PITCH OF MIRROR. PLACE ONE (N)
TOOTH LOCK WASHER BETWEEN MIRROR AND (C) STAND-OFF BRACKET AND TIGHTEN.
TOOLS REQUIRED
4MM HEX DRIVE WRENCH
6MM HEX DRIVE WRENCH
8MM HEX DRIVE WRENCH
A
C
D
E
GH
F
PARTS INDEX
A. RAM TOP CLEVIS WITH BALL (QTY. 1)
B. RAM CLEVIS BASE WITH HOLE FOR BOLT (QTY. 1)
C. MIRROR STAND-OFF BRACKET (QTY. 1)
D. O-RING (QTY. 2)
E. #10-24 X 1” SOCKET HEAD SCREW (QTY. 1)
F. #10-24 NYLOCK NUT (QTY. 1)
G. M10 X 1.25 X 40MM SOCKET HEAD CAP SCREW (QTY. 1)
H. M8 X1.25 X 40MM SOCKET HEAD CAP SCREW (QTY. 1)
J. M10 X 1.25 THIN HEX NUT (QTY. 2)
K. M8 X 1.25 THIN HEX NUT (QTY. 2)
L. M10 X 1.25 X 20MM SOCKET HEAD CAP SCREW (QTY. 1)
M. M8 X 1.25 X 20MM SOCKET HEAD CAP SCREW (QTY. 1)
N. M10 TOOTH LOCK WASHER (QTY. 3)
B
J
K
LM
N
STEP 1:
LOCATE THREADED FEMALE HOLE ON YOUR MOTORCYCLE AND VERIFY THE APPROPRIATE THREAD PITCH BY CAREFULLY THREADING ONE OF (G, H, L or M) SCREWS
PROVIDED. THE LENGTH OF THE CORRECT SCREW WILL DEPEND ON WHICH OF THE TWO OPTIONS YOU SELECT BELOW. PLACE CORRECT SCREW THROUGH
CENTER OPENING OF (B) CLEVIS BASE.
OPTION 2 - NO MIRROR RELOCATION
PLACE (N) TOOTH LOCK WASHER OVER THREAD. USE (L or M) SCREW TO
ATTACH ASSEMBLY TO MOTORCYCLE. (C) STAND-OFF WILL NOT BE USED.
N
L or M
OPTION 2
OPTION 1
N
C
N
N
G or H
J or K
B
B
RMR-INS-B-360
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
RAM® TWIST AND TILT™ BASE ASSEMBLY GUIDE (SIDE B)
RAM® TWIST AND TILT™ BASE ASSEMBLY GUIDE (SIDE B)
STEP 2:
WITH (N) TOOTH LOCK WASHERS IN PLACE (SEE STEP 1), PLACE
ASSEMBLY OVER THREADED HOLE ON MOTORCYCLE AND FULLY TIGHTEN.
STEP 3
POSITION (D) O-RINGS OVER RECESSED
GROOVES ON EACH SIDE OF (A) TOP CLEVIS. O-
RINGS MUST BE SEATED PROPERLY FOR EASY
ADJUSTMENT. INSERT (A) TOP CLEVIS WITH (D) O-
RINGS INTO (B) CLEVIS BASE AND FASTEN USING
(E) SCREW AND (F) NUT. ADJUST TO DESIRED
ANGLE AND FULLY TIGHTEN.
**IMPORTANT SAFETY NOTICE**
IT IS NOT SUGGESTED NOR RECOMMENDED TO REMOVE ANY STAINLESS STEEL SCREW AND REPLACE WITH
PIVOT BASE MOUNT. AN EXAMPLE OF THIS WOULD BE THE HANDLEBAR YOKE CLAMP BRACKET OR OTHER VITAL
ATTACHMENT WHICH HOLD ESSENTIAL STRUCTURAL COMPONENTS TOGETHER.
D
A
D
E
F
B
RMR-INS-B-360
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
The exclusive NPI Lifetime Warranty states that all RAM mounting components and parts
are warranted against defect in materials and workmanship for the life of the product or part.
NPI’s Lifetime Warranty covers the mount or its components only. The mounted device is
not covered under the Lifetime Warranty and will not be replaced if damaged as a result of
mount failure. This warranty is expressly limited to the persons in the United States, and all
foreign countries who purchase RAM for resale or use in the ordinary course of the buyer’s
business. This warranty does not cover any product or part that has been abused, worn out,
heated, ground or otherwise altered, used for a purpose other than that for which it was
intended, or used in a manner inconsistent with any instructions regarding its use.
LIFETIME WARRANTY ON ALL MOUNTING COMPONENTS
STEP 2:
WITH (N) TOOTH LOCK WASHERS IN PLACE (SEE STEP 1), PLACE
ASSEMBLY OVER THREADED HOLE ON MOTORCYCLE AND FULLY TIGHTEN.
STEP 3
POSITION (D) O-RINGS OVER RECESSED
GROOVES ON EACH SIDE OF (A) TOP CLEVIS. O-
RINGS MUST BE SEATED PROPERLY FOR EASY
ADJUSTMENT. INSERT (A) TOP CLEVIS WITH (D) O-
RINGS INTO (B) CLEVIS BASE AND FASTEN USING
(E) SCREW AND (F) NUT. ADJUST TO DESIRED
ANGLE AND FULLY TIGHTEN.
**IMPORTANT SAFETY NOTICE**
IT IS NOT SUGGESTED NOR RECOMMENDED TO REMOVE ANY STAINLESS STEEL SCREW AND REPLACE WITH
PIVOT BASE MOUNT. AN EXAMPLE OF THIS WOULD BE THE HANDLEBAR YOKE CLAMP BRACKET OR OTHER VITAL
ATTACHMENT WHICH HOLD ESSENTIAL STRUCTURAL COMPONENTS TOGETHER.
D
A
D
E
F
B
RMR-INS-B-360
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
The exclusive NPI Lifetime Warranty states that all RAM mounting components and parts
are warranted against defect in materials and workmanship for the life of the product or part.
NPI’s Lifetime Warranty covers the mount or its components only. The mounted device is
not covered under the Lifetime Warranty and will not be replaced if damaged as a result of
mount failure. This warranty is expressly limited to the persons in the United States, and all
foreign countries who purchase RAM for resale or use in the ordinary course of the buyer’s
business. This warranty does not cover any product or part that has been abused, worn out,
heated, ground or otherwise altered, used for a purpose other than that for which it was
intended, or used in a manner inconsistent with any instructions regarding its use.
LIFETIME WARRANTY ON ALL MOUNTING COMPONENTS