Table of Contents
RAM Mounts RAM-B-411U User Manual
Displayed below is the user manual for RAM-B-411U by RAM Mounts which is a product in the Mounting Kits category. This manual has pages.
Related Manuals
RAM® Gas Tank Mount Assembly Guide
Included Hardware:
A. RAM Gas Tank Bracket (QTY. 1)
B. RAM Ball Adapter with Hex Pad (QTY. 1)
C. #10-24 x 1 ½” Machine Screw (QTY. 1)
D. #10-24 Nylock Nut (QTY. 1)
E. #10 x 1” Fender Washer (QTY. 1)
F. M5-0.8 x 40mm Socket Head Cap Screw (QTY. 4)
G. M5-0.8 x 25mm Socket Head Cap Screw (QTY. 3)
H. M5 Flat Washer (QTY. 4)
RMR-INS-411
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
Assemble (B) RAM Ball to (A) Gas Tank Bracket as shown: Place the gas tank base on your traditional gas cap to determine the
correct alignment with the bolts, and desired position of the RAM Ball.
Important: Bolt alignment must be symmetrical.
Sort and verify all hardware and components prior to installation.
For Kawasaki:
(G) 25mm Screws - Qty. 3
For BMW:
(F) 40mm Screws - Qty. 4
Use any combination of the provided hardware to replace the factory
screws on your gas cap when installing. It is important to note that each of
the screws on your gas cap may have different lengths. For every factory
screw you replace, the replacement screw should be approximately 12mm
longer. Place provided washers under cap screw heads when installing.
Some bikes may require unique hardware to
properly install this base. Depending on your
configuration, 3rd party hardware may be required.
Common Hardware for Bike Models:
B
A
C
D
E
FG
H
J
K
L
M
D
B
A
C
E
RAM® Gas Tank Mount Assembly Guide
Included Hardware:
A. RAM Gas Tank Bracket (QTY. 1)
B. RAM Ball Adapter with Hex Pad (QTY. 1)
C. #10-24 x 1 ½” Machine Screw (QTY. 1)
D. #10-24 Nylock Nut (QTY. 1)
E. #10 x 1” Fender Washer (QTY. 1)
F. M5-0.8 x 40mm Socket Head Cap Screw (QTY. 4)
G. M5-0.8 x 25mm Socket Head Cap Screw (QTY. 3)
H. M5 Flat Washer (QTY. 4)
RMR-INS-411
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
Assemble (B) RAM Ball to (A) Gas Tank Bracket as shown: Place the gas tank base on your traditional gas cap to determine the
correct alignment with the bolts, and desired position of the RAM Ball.
Important: Bolt alignment must be symmetrical.
Sort and verify all hardware and components prior to installation.
For Kawasaki:
(G) 25mm Screws - Qty. 3
For BMW:
(F) 40mm Screws - Qty. 4
Use any combination of the provided hardware to replace the factory
screws on your gas cap when installing. It is important to note that each of
the screws on your gas cap may have different lengths. For every factory
screw you replace, the replacement screw should be approximately 12mm
longer. Place provided washers under cap screw heads when installing.
Some bikes may require unique hardware to
properly install this base. Depending on your
configuration, 3rd party hardware may be required.
Common Hardware for Bike Models:
B
A
C
D
E
FG
H
D
B
A
C
E