RAM Mounts RAM-GDS-DOCK-V2-AP2U User Manual
Displayed below is the user manual for RAM-GDS-DOCK-V2-AP2U by RAM Mounts which is a product in the Mobile Device Dock Stations category. This manual has pages.
Related Manuals
A
B
GDS™ Vehicle Dock Assembly Guide (Side A)
C
D
EF
G
H
RPR-INS-GDS-DOCK-V2
1. Use five (D) Screws to attach (B) Top cup to (A)
Back Plate.
Assembly
2. Use five (D) screws to attach (C) Docking cup to
bottom of (A) Back plate.
To prevent screws from protruding behind
vehicle dock, avoid over-tightening.
3. Use (E or F) Screws and (G) Nuts to attach vehicle dock to any
RAM® mounting system, depending on the type of the component used:
4. Insert Micro USB 2.0 cable into GDS™ Dock’s Micro USB 2.0
receiver. When plugged in, tablet will detect power source within two
seconds. User must supply a USB wall charger or cigarette adapter
with appropriate charging specifications for mounted device.
5. Snap USB cable into (H) cable retention clip. 6. Using (D) Screw, attach (H) Cable retention clip into any of the
available wholes shown behind vehicle dock.
Adjust USB cable appropriately along
cable retention clip before tightening.
Parts Index:
A. Vehicle Dock Backing Plate (QTY. 1)
B. Top Cup (QTY. 1) Cup Design May Vary
C. GDS™ Docking Cup (QTY. 1)
D. #4 X 3/8” Sheet Metal Screw (QTY. 10)
E. #8 X 5/8” Machine Screw (QTY. 4)
F. #8 X ½” Machine Screw (QTY. 4)
G. #8 Nylock Nut (QTY. 4)
H. Cable Retention Clip (QTY. 1)
National Products Inc.
8410 Dallas Ave S
Seattle WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
Lack of or improper use of wire
retnetion/cable management may void
warranty.
Composite Components:
Use (F) Screw
Metal Components:
Use (E) Screw
B
A
DD
C
EF
H
For open cockpit or outdoor use, it is recommended to apply
electrical tape to your USB connection.
H
GDS™ Vehicle Dock Assembly Guide (Side B)
Proper Insertion of IntelliSkin™
1. Insert top of tablet upward against top cup,
expanding spring tension.
2. Press bottom of tablet flush against
Tab-Tite back plate.
3. Rest bottom of tablet straight downward, docking ont the
pins of docking cup. When plugged in, tablet will detect
power source within two seconds.
4. To remove, pull tab upward, located on back of vehicle dock.
The exclusive NPI Lifetime Warranty states that all GDS™ non-electronic
components and parts are warranted against defect in materials and workmanship for
the life of the product or part. NPI’s Lifetime Warranty covers the product or its
components only. The mounted device is not covered under the Lifetime Warranty
and will not be replaced if damaged as a result of mount failure. This warranty is
expressly limited to persons in the United States, and all foreign countries who
purchase GDS™ for resale or use in the ordinary course of the buyer’s business. This
warranty does not cover any product or part that has been abused, worn out, heated,
ground or otherwise altered, used for a purpose other than that for which it was
intended, or used in a manner inconsistent with any instructions regarding its use.
3 YEAR WARRANTY ON ALL ELECTRONIC COMPONENTS
LIFETIME WARRANTY ON ALL NON-ELECTRONIC COMPONENTS
MORE DOCKS AND DEVICES WITH GDS™ TECHNOLOGY
GDS™ 6 Gang Dock
Charger
National Products Inc.
8410 Dallas Ave S
Seattle WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
GDS™ Desktop
Dock Pro
GDS™ Locking
Vehicle Dock
GDS™ to USB
Adapter
Visit for alternate docks or IntelliSkin™ for any tablet or phone.www.gdstech.com
RPR-INS-GDS-DOCK-V2
GDS™ Vehicle
Phone Dock