Read all instructions thoroughly before beginning installation. For additional questions and concerns that may not be covered in this manual, please contact

RAM® Mounts support at rammount.com/support.

rammount.com

1.800.499.7479

support@rammount.com

Safety Precaution

Do not install this product near or over an airbag deployment area or in a location that obstructs the driver’s vision or interferes with vehicle

operation. National Products, Inc does not assume responsibility or liability for any such personal injury, death or property damage.

Non-Locking

RAM-HOL-PAN11PU

Key-Locking

RAM-HOL-PAN11PKLU

Combo-Locking

RAM-HOL-PAN11PCLU

To see more mounting options, visit RamMount.com This document, including images, may not be reproduced partly or fully without the expressed written consent of National Products, Inc.

rammount.com

1.800.499.7479

support@rammount.com

ASSEMBLY

MOUNTING OPTIONS

RAM® Diamond Ball RAM® Square Post Clamp

RAM-247U-4

This clamping base is ideal for forklifts and square posts up to

4” in width; made of powder-coated, marine-grade aluminum

with stainless steel hardware.

Compatible with all RAM® Powered

Docks for the Panasonic FZ-N1;

ball and socket technology allows

for near-inﬁnite adjustability and

mounting options.

RAM® Double Socket Arm

RAM-201U

RAM® Diamond Ball Base

RAM-238U

RAM® Double U-Bolt Ball Base

RAM-235-1U

This base includes zinc-coated double U-bolt hardware to

support any round rail from 1.25” to 1.5” in diameter.

RAM® Tough-Claw™

RAP-404U

Available in alternate sizes, this RAM® Tough-Claw™

can clamp to rails ranging from 1” to 1.875” in diameter

without the use of any tools. Quickly tighten and loosen

the knob to connect to any rail or transfer to alternate

mounting locations easily.

View hundreds of interchangeable mounting components available

at rammount.com/components

Part Index

*not to scale

* Not Included

x 2

x 1

rammount.com

1.800.499.7479

support@rammount.com

PRODUCT OVERVIEW

DOCKING THE DEVICE

BACK

SIDE

TOPFRONT

6.78"

3.15"

7.85"

3.90"

3 4

1 2 3

Insert top of device,

pushing upward on the top

cup to expand the dock a

minimum of 7.85 inches.

Push the back of the

device ﬂat against the

cradle.

Carefully release unit so

it makes contact with

pogo pins.

To remove the device simply reverse the above directions

1. Hardware attachment point

2. Guide for device

3. Clearance for headset jack

4. Clearance for power button

5. Spring loaded top cup

6. Cable Retention Option

7. Pogo pins

8. Locking Mechanism

9. Stylus holder

10. Power cable

If pogo pins are damaged in

any way, please do not use the

cradle! PCB must be immediately

replaced to prevent damage to

your device and cradle electronics.

rammount.com

1.800.499.7479

support@rammount.com

HANDLING CAUTIONS

Pinching Hazard

The cradle is spring loaded and may snap closed, pinching

the skin of your hand if not careful. Avoid close contact

with the top cup of cradle.

Avoid Hand Strap Interference

Ensure hand strap or anything external is not in contact

with the pogo pins. This can damage them and disable the

holder’s charging capabilities.

Charging Cord Placement

Charging cord must be zip-tied to the back of the cradle

to prevent unnecessary strain to the connection point

on the holder.

COMBINATION LOCK

Unlock Mode

To unlock, align factory preset combination, or

current combination (A), and pull plunger (C)

outward away from notched ring (B).

Plunger IN: Device latch will be locked in position

Plunger OUT: Latch will be loose

Set lock to unlock mode (see above), with

plunger pulled outward.

Rotate notched ring until it stops.

Set new combination.

Rotate notched ring back to original

position. New combination will be set.

Changing Lock Combination