RAM Mounts RAM-VB-196-SW1 User Manual
Displayed below is the user manual for RAM-VB-196-SW1 by RAM Mounts which is a product in the Notebook Stands category. This manual has pages.
Related Manuals
Placement
Passenger side on the floor using the seat leg
bolts to anchor product. This base is not for use
in GM vehicles with front seat leg hooks.
Drilling Required
For many vehicles drilling is not required but for
some applications, drilling may be necessary.
Seat Configuration
Bucket/Bench
Construction/Finish
Steel/Black Powdercoat
Pole or Pedestal
Lower tube is welded to base
Weight
5.6 lbs.
Dimensions
A = 20.125”, B = 5.75", C = 9.75",
Hole Center = 9.00” min to 8.875” max
Cutting Required
For some applications, it may be necessary to
cut the welded tube shorter. An example of this
would be installing the base between the seat
frame box and seat track of a vehicle.
Notes
Slotted design allows this base to fit a wide variety of
vehicles. This base will not interfere with factory installed
console in most installations. Product has 16.188” min
base width but accommodates as low as 9” hole
center seat leg bolts.
RAM No-Drill TM Seat Bases
Item Number
RAM-VB-196 & RAM-VB-196-SW1
Complete Vehicle Mount
RAM-VB-196-SW1
Vehicle Base
RAM-VB-196
SPECIFICATIONS INSTALLATION INSTRUCTIONS
INSTALL INSTR. FOR TOPKICK and KODIAK
This product may be installed in several ways. It is up to the installer to determine the best location for the product.
Typical location are:
Under seat frame legs.
Over seat frame legs using supplied spacers and longer bolts.
Between seat frame and seat tracks.
1. Move the passenger seat to the rear-most position.
2. Remove or loosen the front seat leg bolts that secure the passenger side seat legs to the floor pan.
3. If installing under the seat legs, gently lift the front of the seat and place the base under the front of the seat frame
legs. Given the many applications for this product, what is stated here may not apply to your vehicle.
4. With the base positioned per your application, fully tighten mounting hardware to secure the seat legs
and no drill base into the vehicle.
Tips.
Iif using the supplied stand off tubes, choose the set that will sit the most flat in the seat bolt pocket. Also carefully
match up the thread of the factory bolt to the thread of the supplied bolt to insure they are an exact match. If you cannot
find a match, you will need to source the correct bolts.
RAM Mounting Systems
RMR-INS-VB-196
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com RMR-INS-VB-196
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
RAM-VB-196-1 & RAM-VB-196-1-SW1
Reverse Configuration
RAM-VB-196-1-SW1
Reverse Configuration
RAM-VB-196-1
RAM No-Drill TM Seat Bases
Item Number
RAM-VB-196 & RAM-VB-196-SW1 RAM Mounting Systems
RAM-VB-196-1 & RAM-VB-196-1-SW1
Installation photo of RAM-VB-196 in a Toyota Prius. Your
vehicle installation may vary from the one depicted here.
Placement
Passenger side on the floor using the seat leg
bolts to anchor product. This base is not for use
in GM vehicles with front seat leg hooks.
Drilling Required
For many vehicles drilling is not required but for
some applications, drilling may be necessary.
Seat Configuration
Bucket/Bench
Construction/Finish
Steel/Black Powdercoat
Pole or Pedestal
Lower tube is welded to base
Weight
5.6 lbs.
Dimensions
A = 20.125”, B = 5.75", C = 9.75",
Hole Center = 9.00” min to 8.875” max
Cutting Required
For some applications, it may be necessary to
cut the welded tube shorter. An example of this
would be installing the base between the seat
frame box and seat track of a vehicle.
Notes
Slotted design allows this base to fit a wide variety of
vehicles. This base will not interfere with factory installed
console in most installations. Product has 16.188” min
base width but accommodates as low as 9” hole
center seat leg bolts.
RAM No-Drill TM Seat Bases
Item Number
RAM-VB-196 & RAM-VB-196-SW1
Complete Vehicle Mount
RAM-VB-196-SW1
Vehicle Base
RAM-VB-196
SPECIFICATIONS INSTALLATION INSTRUCTIONS
INSTALL INSTR. FOR TOPKICK and KODIAK
This product may be installed in several ways. It is up to the installer to determine the best location for the product.
Typical location are:
Under seat frame legs.
Over seat frame legs using supplied spacers and longer bolts.
Between seat frame and seat tracks.
1. Move the passenger seat to the rear-most position.
2. Remove or loosen the front seat leg bolts that secure the passenger side seat legs to the floor pan.
3. If installing under the seat legs, gently lift the front of the seat and place the base under the front of the seat frame
legs. Given the many applications for this product, what is stated here may not apply to your vehicle.
4. With the base positioned per your application, fully tighten mounting hardware to secure the seat legs
and no drill base into the vehicle.
Tips.
Iif using the supplied stand off tubes, choose the set that will sit the most flat in the seat bolt pocket. Also carefully
match up the thread of the factory bolt to the thread of the supplied bolt to insure they are an exact match. If you cannot
find a match, you will need to source the correct bolts.
RAM Mounting Systems
RMR-INS-VB-196
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com RMR-INS-VB-196
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
RAM-VB-196-1 & RAM-VB-196-1-SW1
Reverse Configuration
RAM-VB-196-1-SW1
Reverse Configuration
RAM-VB-196-1
RAM No-Drill TM Seat Bases
Item Number
RAM-VB-196 & RAM-VB-196-SW1 RAM Mounting Systems
RAM-VB-196-1 & RAM-VB-196-1-SW1
Installation photo of RAM-VB-196 in a Toyota Prius. Your
vehicle installation may vary from the one depicted here.