RAM Mounts RAP-299-3-UN11U User Manual
Displayed below is the user manual for RAP-299-3-UN11U by RAM Mounts which is a product in the Holders category. This manual has pages.
Related Manuals
RAM X-Grip® ASSEMBLY INSTRUCTIONS (SIDE A)
PARTS INDEX:
A. RAM X-Grip® SUB ASSEMBLY (QTY. 1)
B. RAM CRADLE SLIDE SUPPORTS (QTY. 2)
C. ROUND RUBBER CAPS (QTY. 8)
D. THIN RUBBER CAPS (QTY. 2)
E. #8-32 X ½” MACHINE SCREW (QTY
. 2)
F. #8-32 NYLOCK NUT (QTY. 2)
G. #8 X ½” SHEET METAL SCREW (QTY. 4)
H. #8 X 5/8” SHEET METAL SCREW (QTY. 2)
A
B
D
RUBBER CAPS
- ATTACH (C) ROUND CAPS TO EACH PRONG THAT
MAKES CONTACT WITH YOUR TABLET.
ATTACHING SLIDE SUPPORTS (NOT REQUIRED)
1. POSITION (F) NUT AT BOTTOM OF SLOTTED HOLE ON
(B) SLIDE SUPPORT.
2. POSITION SLIDE AT AN ANGLE (AS SHOWN)
INTO BOTTOM HOLE OF (A) X-Grip™ ASSEMBLY.
PRESS SLIGHTLY AGAINST INTERNAL SPRING,
AND ANGLE (B) SLIDE SUPPORT BACK TO
PINCH (F) NUT AGAINST EDGE OF HOLDER.
ATTACHING RAM X-Grip® TO RAM MOUNT
FOR ATTACHING TO METAL OR ROUND BALL ADAPTERS,
USE (G) ½” SCREWS ALONG ANY OF THE HOLE
PATTERNS.
FOR ATTACHING TO COMPOSITE DIAMOND BALL
ADAPTER (RAP-B-238U), USE (H) 5/8” SCREWS
ALONG ANY OF THE HOLE PATTERNS.
C
EFG
G
G
G
GH
H
F
B
DURING THIS STEP, USE CAUTION TO PREVENT
NUT FROM FALLING INSIDE OF X-Grip®
ASSEMBLY.
H
C
D
RMR-INS-UN9
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
- ATTACH (D) THIN CAPS TO HANDLE PRONGS
LOCATED BEHIND RAM X-GRIP®.
RAM X-Grip® ASSEMBLY INSTRUCTIONS (SIDE A)
PARTS INDEX:
A. RAM X-Grip® SUB ASSEMBLY (QTY. 1)
B. RAM CRADLE SLIDE SUPPORTS (QTY. 2)
C. ROUND RUBBER CAPS (QTY. 8)
D. THIN RUBBER CAPS (QTY. 2)
E. #8-32 X ½” MACHINE SCREW (QTY
. 2)
F. #8-32 NYLOCK NUT (QTY. 2)
G. #8 X ½” SHEET METAL SCREW (QTY. 4)
H. #8 X 5/8” SHEET METAL SCREW (QTY. 2)
A
B
D
RUBBER CAPS
- ATTACH (C) ROUND CAPS TO EACH PRONG THAT
MAKES CONTACT WITH YOUR TABLET.
ATTACHING SLIDE SUPPORTS (NOT REQUIRED)
1. POSITION (F) NUT AT BOTTOM OF SLOTTED HOLE ON
(B) SLIDE SUPPORT.
2. POSITION SLIDE AT AN ANGLE (AS SHOWN)
INTO BOTTOM HOLE OF (A) X-Grip™ ASSEMBLY.
PRESS SLIGHTLY AGAINST INTERNAL SPRING,
AND ANGLE (B) SLIDE SUPPORT BACK TO
PINCH (F) NUT AGAINST EDGE OF HOLDER.
ATTACHING RAM X-Grip® TO RAM MOUNT
FOR ATTACHING TO METAL OR ROUND BALL ADAPTERS,
USE (G) ½” SCREWS ALONG ANY OF THE HOLE
PATTERNS.
FOR ATTACHING TO COMPOSITE DIAMOND BALL
ADAPTER (RAP-B-238U), USE (H) 5/8” SCREWS
ALONG ANY OF THE HOLE PATTERNS.
C
EFG
G
G
G
GH
H
F
B
DURING THIS STEP, USE CAUTION TO PREVENT
NUT FROM FALLING INSIDE OF X-Grip®
ASSEMBLY.
H
C
D
RMR-INS-UN9
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
- ATTACH (D) THIN CAPS TO HANDLE PRONGS
LOCATED BEHIND RAM X-GRIP®.
3. WHILE HOLDING (B) SLIDE IN PLACE FROM STEP 2, INSERT (E)
SCREW AT AN ANGLE TO LINE UP WITH (F) NUT. THREAD BY
HAND UNTIL THE SCREW LOCKS IN WITH THE THREADS.
4. ONCE (E) SCREW IS THREADED BY HAND INTO (F)
NUT, STRAIGHTEN (B) SUPPORT SLIDE AND FULLY
TIGHTEN USING SCREWDRIVER.
5. REPEAT STEPS 1 - 4 FOR SECOND SUPPORT SLIDE. POSITION TABLET
IN HOLDER AND ADJUST SLIDES AS NEEDED. WHEN ADJUSTING SUPPORT
SLIDES, DO NOT LOOSEN (E) SCREW BY MORE THAN THREE TURNS.
The exclusive NPI Lifetime Warranty states that all RAM mounting components and parts are warranted
against defect in materials and workmanship for the life of the product or part. NPI’s Lifetime Warranty
covers the mount or its components only. The mounted device is not covered under the Lifetime
Warranty and will not be replaced if damaged as a result of mount failure. This warranty is expressly
limited to the persons in the United States, and all foreign countries who purchase RAM for resale or
use in the ordinary course of the buyer’s business. This warranty does not cover any product or part
that has been abused, worn out, heated, ground or otherwise altered, used for a purpose other than that
for which it was intended, or used in a manner inconsistent with any unstructions regarding its use.
LIFETIME WARRANTY ON ALL MOUNTING COMPONENTS
E
RAM X-Grip® ASSEMBLY INSTRUCTIONS (SIDE B)
RMR-INS-UN9
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
3. WHILE HOLDING (B) SLIDE IN PLACE FROM STEP 2, INSERT (E)
SCREW AT AN ANGLE TO LINE UP WITH (F) NUT. THREAD BY
HAND UNTIL THE SCREW LOCKS IN WITH THE THREADS.
4. ONCE (E) SCREW IS THREADED BY HAND INTO (F)
NUT, STRAIGHTEN (B) SUPPORT SLIDE AND FULLY
TIGHTEN USING SCREWDRIVER.
5. REPEAT STEPS 1 - 4 FOR SECOND SUPPORT SLIDE. POSITION TABLET
IN HOLDER AND ADJUST SLIDES AS NEEDED. WHEN ADJUSTING SUPPORT
SLIDES, DO NOT LOOSEN (E) SCREW BY MORE THAN THREE TURNS.
The exclusive NPI Lifetime Warranty states that all RAM mounting components and parts are warranted
against defect in materials and workmanship for the life of the product or part. NPI’s Lifetime Warranty
covers the mount or its components only. The mounted device is not covered under the Lifetime
Warranty and will not be replaced if damaged as a result of mount failure. This warranty is expressly
limited to the persons in the United States, and all foreign countries who purchase RAM for resale or
use in the ordinary course of the buyer’s business. This warranty does not cover any product or part
that has been abused, worn out, heated, ground or otherwise altered, used for a purpose other than that
for which it was intended, or used in a manner inconsistent with any unstructions regarding its use.
LIFETIME WARRANTY ON ALL MOUNTING COMPONENTS
E
RAM X-Grip® ASSEMBLY INSTRUCTIONS (SIDE B)
RMR-INS-UN9
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com