Salicru 698OP000022 User Manual
Displayed below is the user manual for 698OP000022 by Salicru which is a product in the UPS Accessories category. This manual has pages.
Related Manuals
USER'S MANUAL
RACK MOUNTING MANUAL BYPASS
BM-R 3, 6 and 10 kVA
2SALICRU
3
General index.
1. INTRODUCTION.
1.1. THANK YOU LETTER.
2. SAFETY INFORMATION.
2.1. USING THIS MANUAL.
2.1.1. Conventions and symbols used.
2.2. ADDITIONAL SAFETY PRECAUTIONS.
3. QUALITY ASSURANCE AND STANDARDS.
3.1. STATEMENT BY THE MANAGEMENT.
3.2. STANDARDS.
3.3. ENVIRONMENT.
4. OVERVIEW.
4.1. VIEWS.
4.1.1. Equipment front views.
4.1.2. Corresponding legend of the equipment's views.
4.2. PRODUCT DEFINITION.
4.2.1. Nomenclature.
5. DESCRIPTION.
6. INSTALLATION.
6.1. RECEPTION OF THE EQUIPMENT.
6.1.1. Reception, unpacking and contents.
6.2. LOCATION AND CONSIDERATIONS.
6.2.1.1. Location.
6.3. WIRING.
7. OPERATING.
7.1. START UP.
7.2. TRANSFERENCE FROM «NORMAL» OR «UPS» MODE TO
«BYPASS».
7.2.1. 3 kVA manual bypass models, from «NORMAL» to
«BYPASS» mode.
7.2.2. 6 and 10 kVA manual bypass models, from «UPS» to
«BYPASS» mode.
7.3. TRANSFERENCE FROM «BYPASS» TO «NORMAL» OR
«UPS» MODE.
7.3.1. 3 kVA manual bypass models, from «BYPASS» to
«NORMAL» mode.
7.3.2. 6 and 10 kVA manual bypass models, from «BYPASS» to
«UPS» mode.
8. MAINTENANCE, WARRANTY AND SERVICE.
8.1. MAINTENANCE.
8.2. WARRANTY CONDITIONS.
8.2.1. Warranty terms.
8.2.2. Out of scope of supply.
8.3. TECHNICAL SERVICE NETWORK.
9. ANNEXES.
9.1. TECHNICAL SPECIFICATIONS.
BM-R Rack mounting manual bypass USER'S MANUAL
4SALICRU
SALICRU
1. INTRODUCTION.
1.1. THANK YOU LETTER.
We thank you in advance for the trust placed in us in the
purchasing of this product. Read this instruction manual
carefully in order to familiarize yourself with its content,
since the more you know and understand the equipment the
greater your satisfaction, level of safety and optimization of its
functionalities will be.
We remain at your disposal for any additional information or
queries that you may wish to make.
Yours sincerely.
•The equipment described herein is capable of causing
significant physical damage in the event of improper
handling. For this reason its installation, maintenance
and/or repair must be carried out exclusively by our per-
sonnel or by qualified personnel.
•Although no effort has been spared to ensure that the
information in this user manual is complete and accurate,
we are not responsible for any errors or omissions that may
exist.
The images included in this document are for illustrative
purposes and may not represent exactly the parts of the
equipment shown, therefore they are not contractual. How-
ever, any divergence that may arise will be remedied or
solved with the correct labelling on the unit.
•Following our policy of constant evolution, we reserve
the right to modify the characteristics, operations
or actions described in this document without prior
notice.
•Reproduction, copying, assignment to third parties,
modification or total or partial translation of this
manual or document, in any form or by any means,
without previous written authorization by our firm is
prohibited, with the full and exclusive property rights over
the same being reserved by our firm.
5
2. SAFETY INFORMATION.
2.1. USING THIS MANUAL.
The documentation of any standard equipment is available to
the customer on our website for download (www.salicru.
com).
•For devices “powered by socket”, this is the website for
obtaining the user manual and “Safety Instructions”
EK266*08.
•For devices with “permanent connection” via terminals, a
CD-ROM or pen drive containing all necessary information
for connection and start-up, including “Safety Instruc-
tions” EK266*08, may be supplied with it.
Before carrying out any action on the device relating to its
installation or start-up, change of location, configuration or
handling of any kind, carefully read the safety instructions.
The purpose of the user manual is to provide information
regarding safety and explanations of the procedures for
installation and operation of the equipment. Read them carefully
and follow the steps indicated in the order established.
Compliance with the "Safety Instructions" is
mandatory and the user is legally responsible for
compliance and enforcement.
The equipment is delivered properly labelled for the correct
identification of each of the parts, which together with the
instructions described in this user manual allows the operations
of installation and commissioning to be performed in a simple
and orderly manner without having any doubts whatsoever.
Finally, once the equipment is installed and operating, it is
recommended to save the documentation downloaded from the
website, CD-ROM or Pen Drive in a safe and easy-to-access
place, for any future queries or doubts that may arise.
The following terms are used interchangeably in the document
to refer to:
•«Manual bypass, Bypass, equipment or unit».- Rack
mounting manual bypass.
•«T.S.S.».- Technical Service and Support.
•«Client, installer, operator or user».- These are used
interchangeably and by extension to refer to the installer
and/or operator who will carry out the corresponding
actions, and the same person may be responsible for
carrying out the respective actions when acting on behalf
of, or in representation of, same.
2.1.1. Conventions and symbols used.
Some symbols may be used and appear on the equipment,
batteries and/or in the context of the user manual.
For more information, see section 1.1.1 of document EK266*08
on «Safety instructions».
2.2. ADDITIONAL SAFETY PRECAUTIONS.
•In the point of view of installation and electrical safety,
the rack mounting manual bypass must be considered as a
transformer or distribution line.
•As this is an equipment with protection against electrical
shocks class I, it is essential to supply or install the main
protection earth cable ( ), through either the AC wall
outlet or corresponding terminal.
•Those models with terminals, they have to be in-
stalled by both qualified personnel and per-
sonnel with particular training which can make the
shifting manoeuvring with the help of this document.
•The instructions that being read are relating to the own
manual bypass only. Any other action related to this docu-
ment, which involves any manoeuvring over any other
equipment like a UPS or stabilizer, it will be done as its
user’s manual states.
•The neutral regime from input to output is identical for the
bypass panels “with no galvanic isolation”. The neutral re-
gime must always be the same for the manual bypass as
well as the UPS or stabilizer.
BM-R Rack mounting manual bypass USER'S MANUAL
6SALICRU
3. QUALITY ASSURANCE AND STANDARDS.
3.1. STATEMENT BY THE MANAGEMENT.
Our goal is customer satisfaction, therefore this Management
has decided to establish a Quality and Environment Policy,
through the implementation of a Quality and Environmental
Management System that will enable us to comply with the
requirements demanded in the ISO 9001 and ISO 14001 and
also by our Customers and Stakeholders.
Likewise, the management of the company is committed to the
development and improvement of the Quality and Environmental
Management System, through:
•Communication to the entire company of the importance of
satisfying both the client's requirements as well as legal
and regulatory requirements.
•The dissemination of the Quality and Environment Policy
and the setting of the Quality and Environment objectives.
•Conducting reviews by the Management.
•Providing the necessary resources.
3.2. STANDARDS.
The Manual Bypass product is designed, manufactured and
commercialized in accordance with the standard EN ISO 9001
of Quality Management Systems and certified by SGS body.
The marking shows the conformity to the EEC Directive by
means of the application of the following standards:
•2014/35/EU. - Low Voltage Directive (LVD).
•2011/65/EU. - Restriction of Hazardous Substances in elec-
trical and electronic equipment (RoHS).
The manufacturers responsibility is excluded in the
event of any modification or intervention in the product
by the customer’s side.
Declaration of conformity CE of the product is at the
client disposal under previous request to our headquar-
ters offices.
3.3. ENVIRONMENT.
This product has been designed to respect the environment and
manufactured according to ISO 14001.
Recycling of the equipment at the end of its useful life:
Our company undertakes to use the services of authorized and
regulatory companies to treat the set of products recovered at
the end of their useful life (contact your distributor).
Packaging:
For the recycling of the packaging there must be compliance
with the legal requirements in force, according to the specific
regulations of the country where the equipment is installed.
7
4. OVERVIEW.
4.1. VIEWS.
4.1.1. Equipment front views.
Fig. 1 and 2 show the corresponding illustrations of the rack
mounting manual bypass, ready to be installed in 19" rack cabi-
nets, although the 3 kVA model allows wall mounting installa-
tion too see section 6 installation.
4 8 123
7
14 14
Fig. 1. Front view of the 3kVA rack mounting manual
bypass.
12 6 13
5
4
3
2
1
5
4U
4N
3U
3N
2R
2N
1R
1N
8 109
1114 14
Respect the phase and neutral rotation, otherwise
there will be a short-circuit when the manual by-
pass switch will be switched.
Fig. 2. Front view of the 6 and 10kVA rack mounting manual
bypass.
4.1.2. Corresponding legend of the equipment's views.
1 AC power supply IEC connector or input terminals.
2 To be connected to the UPS or stabilizer input.
3 To be connected to the UPS or stabilizer output.
4 IEC connectors or output terminals to loads.
5 Main protective earth (6 and 10 kVA models only).
6 Input circuit breaker switch (6 and 10 kVA models only).
7 Output thermic switches (2 sections in the 3 kVA model).
8 Manual bypass switch (Normal or Bypass positions).
9 Manual bypass signal auxiliary contact for signalling.
10 Terminal strip to connect with the EBMS signal of the UPS.
11 Protection cover for terminal power strip.
12 Cable gland for connection cables.
13 Manual bypass switch cover.
14 Angle support and screws to adapt the device to 19" rack
format.
4.2. PRODUCT DEFINITION.
4.2.1. Nomenclature.
BM-TWIN PRO-RT-6 2/2
Output voltage.
Input voltage.
Power.
Series.
Manual bypass acronym.
BM-R Rack mounting manual bypass USER'S MANUAL
8SALICRU
5. DESCRIPTION.
•The manual bypass is an option which allows feeding the
load or loads either from an equipment - UPS or stabilizer-,
or from commercial mains directly without breaking the
power supply during its switching manoeuvring, because it
is make before break type, unless it is used in a wrong way
without respecting the stated procedure in section 7.
•In correlation with Fig. 1 and 2, Fig 3 and 4 illustrations
show the single line diagrams of both structures.
The structure is identical in both figures, although there
are some differences between models. The most important
one is the auxiliary contact from the manual bypass switch,
which comes from a microswitch located in the back side of
the protection cover and connected to a signal connector in-
ternally. By means of the electrical connection with the sup-
plied cable between this connector and the one available in
several equipments like the UPS from TWIN PRO2 and/or
RT2 series, when the protecting cover from manual bypass
is removed, the UPS shifts from «Inverter output mode» to
«Static bypass mode», considering that the system was
on normal mode operating previously. Therefore, it makes
easier the operating and avoids possible wrong manoeu-
vring that it could cause serious damages to the installation
set, loads included.
UPS / STABILIZER
RACK MANUAL BYPASS 16 A
3 IEC
AC input mains to
manual bypass
3 IEC
1 IEC
Equipment IEC
input power supply
connector
Equipment
IEC output
Output to
loads
To
equipment
input
From equipment output
Fig. 3. Wiring between the UPS and the 3 kVA bypass.
UPS / STABILIZER
RACK MANUAL BYPASS 40 /
63 A Output
terminals to
loads
AC input power
suplpy
EMBS connector
To
equipment
input
From equipment output
Equipment input
terminals
Output
terminals
to loads
Fig. 4. Wiring between UPS and 6 and 10 kVA bypass.
9
6. INSTALLATION.
•Read and respect the Safety instructions, described
in section 2 of this document. The fact of omitting
any of the stated indications can cause serious or very se-
rious accidents to the surrounding, as well as failures in the
equipment and/or loads connected to it.
6.1. RECEPTION OF THE EQUIPMENT.
6.1.1. Reception, unpacking and contents.
•Reception. Check that:
Data of the label sticked on the packaging corresponds
to the ones stated in the order. And once it is unpacked,
check the previous data with the ones in the nameplate
of the own manual bypass unit.
In case of any discrepancies, make the nonconformity,
quoting the references in the delivery note.
It has not been damaged during transport.
•Contents.
Rack mounting equipment.
Wiring link with connector and AC inlet (3 kVA model).
Bypass signal cable to be connected with TWIN PRO2
or RT2 UPSs (6 and 10 kVA models).
Angles supports for 19" rack mounting and their screws.
User's manual in hardcopy and warranty.
•Once the reception is finished, if it is not going to be in-
stalled in the next days, it is recommended to keep the
equipment back in its original packaging as a preventive
measure.
•As regards to the packaging, when it is going to be dis-
posed, do it in accordance with the regulations in force.
It is advised to keep it for year, at least.
6.2. LOCATION AND CONSIDERATIONS.
6.2.1.1. Location.
•Remove the angles and screws from the plastic bag and
assemble them on the rack mounting bypass.
•These devices are designed to be integrated into rack
cabinets. Illustrations from Fig 5 and 6 are mere examples
and the first one shows the wall mounting version for 16
A model.
UPS or stabilizer
19" rack installation.
Wall mounting installation.
Fig. 5. Example of 3 kVA manual bypass installation.
UPS or stabilizer
Fig. 6. Example of 6 and 10 kVA manual bypass installation.
6.3. WIRING.
•Any equipment connection, control included (inter-
face, remote control, ...), will be done with all the
switched OFF and with no mains present (power supply
switch of the UPS to «Off»).
•Do not forget that the UPS is an electrical generator,
so the end-user must take the needed cautions
against the direct and indirect contacts, in case the instal-
lation has one.
•For 6 and 10 kVA manual bypass connected to a UPS, the
documentation of itself will be taken into account, as re-
gard the «Backfeed protection». Also, in the installation
itself, it is also stated the cross cable section and protec-
tion size and features, etc.. for a determined power rate. At
least proceed according to these recommendations.
•For 6 and 10 kVA models, remove the terminal protection
cover 11. Once the connection actions are finished, put it
back.
Cover 11 has two cable glands 12 for the use of the
cable entrance. Before connecting the cables to
their respective terminals, remember to pass them through
BM-R Rack mounting manual bypass USER'S MANUAL
10 SALICRU
To the AC wall inlet.
From IEC UPS or stabilizer
output connector
IEC outlets to loads
To IEC UPS or stabilizer
input connector
Fig. 7. Example of 3 kVA manual bypass wiring.
•For 6 and 10 kVA models, the manual bypass has an aux-
iliary contact 10 labelled as EBMS, which has to be con-
nected with its homologous located in the UPS or stabilizer,
where its mission has been previously described.
The risk of short-circuit is increased in case of
wrong manoeuvring, when the UPS or stabilizer do
not have this contact or it has not been connected. Make
the steps following the stated order.
•Illustrations of Fig. 7 and/or 8 show how to connect the
manual bypass with a UPS or stabiliser and loads, de-
pending on its power rate.
Respect the stated input and output strictly, other-
wise the UPS or stabiliser, manual bypass and loads
can be damaged.
•As this is an equipment with protection against
electrical shocks class I, it is essential to install the
main earth protection cable [ ].
In 3 kVA bypass models.
The bypass power supply plug will be connected to a
wall outlet with protection earth duly installed, which
through the IEC connectors will be connected to the en-
tire system.
In 6 and 10 kVA bypass models.
Connect the main earth protection cable 5 to the ter-
minal [ ]. There is a second terminal 5 beside the
output terminals. The earth protection cable to be con-
nected to the UPS or stabilizer can be taken from any
of them.
1N
1R
4U
4N
3U
3N
2R
2N
Bypass
signal
To an AC wall outlet or
grid terminals.
To UPS or stabilizer
input.
From UPS or stabilizer
output.
Fig. 8. Example of 6 an 10 kVA manual bypass wiring.
11
7. OPERATING.
•UPS or stabilizer operating manual, which the manual by-
pass is linked has to be available.
•Make sure that all connections have been done properly
and the instructions and labelling on each device as regards
to installation have been respected.
•It is needed and mandatory to proceed in the established
order.
•Consider the available protections:
In 3 KVA models, two circuit breakers, one for each
output terminal strip with IEC connectors.
In 6 and 10 KVA models, one input circuit breaker of 40
or 63 A respectively.
7.1. START UP.
•Supply voltage to the manual bypass input.
•In the 6 and 10 kVA models, turn the input circuit breaker 6
from manual bypass to «On».
•Start the UPS or stabilizer up, by respecting the steps
stated in their documentation (user's manual).
7.2. TRANSFERENCE FROM «NORMAL» OR «UPS» MODE TO
«BYPASS».
7.2.1. 3 kVA manual bypass models, from «NORMAL» to
«BYPASS» mode.
1. Transfer the own UPS or stabilizer to «Bypass mode» (shutdown
the inverter or the stabiliser, depending on the case, in
order to feed the load through their internal static bypass
switch). Confirm the output voltage availability through the
LCD panel or indicator.
Any transfer manoeuvring will be done with
the UPS or stabilizer on «Bypass mode».
2. Turn the manual bypass switch 8 a from «UPS» to «BYPASS».
The load will be supplied from the AC grid directly.
3. Those UPS or stabilizers models with input circuit breaker, turn
it «Off». The UPS or stabilizer will be out of service com-
pletely.
4. In case, a preventive maintenance, reparation or replacement
of the equipment were needed, disconnect both cables
with the IEC connector, which go from the UPS or stabilizer
to the rack mounting manual bypass.
7.2.2. 6 and 10 kVA manual bypass models, from «UPS» to
«BYPASS» mode.
1. Transfer the own UPS or stabilizer to «Bypass mode» (shutdown
the inverter or the stabiliser, depending on the case, in
order to feed the load through their internal static bypass
switch). Confirm the output voltage availability through the
LCD panel or indicator.
Any transfer manoeuvring will be done with
the UPS or stabilizer on «Bypass mode».
2. Remove the protection cover 13 from the manual bypass switch.
In case the UPS or stabilizer have not been transferred to
«Bypass mode», when the protection cover 13 is removed,
the equipment will shift to this operating mode automati-
cally, provided that the bypass signal 10 of the own rack
mounting bypass is connected with the UPS or stabiliser.
3. Turn the manual bypass switch 8 from «UPS» to «BYPASS». The
load will be supplied from the AC grid directly.
4. Those UPS or stabilizers models with input circuit breaker, turn
it «Off». The UPS or stabilizer will be out of service com-
pletely.
5. In case, a preventive maintenance, reparation or replacement
of the equipment were needed, disconnect the cables be-
tween the UPS or stabilizer and the rack mounting manual
bypass.
It is recommended to disconnect both ends of the
cable, UPS or stabilizer and rack mounting bypass,
in order to avoid any incident of wrong manoeuvring.
7.3. TRANSFERENCE FROM «BYPASS» TO «NORMAL» OR
«UPS» MODE.
7.3.1. 3 kVA manual bypass models, from «BYPASS» to
«NORMAL» mode.
1. Check that the complete set is connected according to section
6.3, as regards to the power of each model.
2. UPS or stabiliser models with input circuit breaker, turn it «On»,
and the «Bypass mode» will be restored (the UPS inverter or
stabiliser has to be turned «Off»).
3. Turn the manual bypass switch 8 from «BYPASS» to «NORMAL».
The load will be supplied through the AC grid through the
UPS or stabiliser static bypass.
Any transfer manoeuvring will be done with
the UPS or stabilizer on «Bypass mode».
4. Turn the UPS inverter or stabilizer «On», by respecting the steps
stated in their documentation (user's manual).
7.3.2. 6 and 10 kVA manual bypass models, from «BYPASS» to
«UPS» mode.
1. Check that the complete set is connected according to section
6.3, as regards to the power of each model.
2. UPS or stabiliser models with input circuit breaker, turn it «On»,
and the «Bypass mode» will be restored (the UPS inverter or
stabiliser has to be turned «Off»).
3. Turn the manual bypass switch 8 from «BYPASS» to «UPS». The
load will be supplied through the AC grid through the in-
ternal UPS or stabiliser static bypass.
Any transfer manoeuvring will be done with
the UPS or stabilizer on «Bypass mode».
4. Put the protection cover 13 of the manual bypass switch back,
otherwise the UPS inverter or stabiliser will not start up.
5. Turn the UPS inverter or stabiliser «On», by respecting the steps
stated in their documentation (user's manual).
BM-R Rack mounting manual bypass USER'S MANUAL
12 SALICRU
8. MAINTENANCE, WARRANTY AND SERVICE.
8.1. MAINTENANCE.
•This product does not require any preventive maintenance.
8.2. WARRANTY CONDITIONS.
8.2.1. Warranty terms.
Warranty conditions for the acquired product can be found in
our website, please register the unit in it. It is recommended
to do it as soon as possible in order to be included in the data
base of our Technical Service and Support (T.S.S.). Among
others benefits, in case of any T.S.S. intervention to fix an
hypothetical failure, the procedure formality will be smoother.
8.2.2. Out of scope of supply.
In case it is detected that the product is not damaged or the
fault was caused by a wrong manoeuvring, negligence, instal-
lation and/or wrong checking, reparation attempts or non-
authorised modifications, or any other cause beyond of the
intended use, or by accident fire, lightnings or other dangers,
our company is not forced by the warranty. Also, it will not
cover any compensation due to the incurred damages.
8.3. TECHNICAL SERVICE NETWORK.
The coverage in both national and international markets for
Technical Service and Support (T.S.S.), can be found in our
Website.
13
9. ANNEXES.
9.1. TECHNICAL SPECIFICATIONS.
Available power rates (kVA ) 3 6 10
Input and output tipology Single phase / Single phase
Male IEC connector or terminals, AC input power
supply IEC connector 3 terminals (phase, neutral and PE)
Female IEC connector or terminals, UPS or
stabilizer power supply IEC connector 3 terminals (phase, neutral and PE)
Female IEC connector or terminals, from UPS or
stabilizer output IEC connector 3 terminals (phase, neutral and PE)
Maximum permissible voltage of the input circuit
breaker 250 V
Input circuit breaker size -40 A 63 A
Maximum permissible voltage of manual bypass
switch 690 V
Maximum permissible current of the manual
bypass switch 16 A 40 A 63 A
Selective output breakers IEC connectors 2 - -
Maximum permissible voltage of the output breakers 250 V
Output breaker size 10 A - -
Number of output connectors or terminals
2 groups of 3 female IEC connectors of
10 A with thermic protection + 1 direct
female IEC connector of 16 A
1 group of 3 terminals (phase, neutral and PE)
Operating relative humidity 0-95 % non-condensing
Protection degree IP20
Dimensions - Depth x Width x Height- (mm) 110 x 438 (480) x 50 mm 160 x 438 (480) x 86 (2U) mm
Weight 1,5 kg 3 kg
Safety EN-IEC 62040-1; EN-IEC 60950-1
Marking CE
Quality System ISO 9001 and ISO 140001
Tab. 1. Technical specifications.
480
438
110
32
Fig. 9. Dimensions BM-R 3 kVA.
480
438
160
39
Fig. 10. Dimensions BM-R 6 and 10 kVA.
BM-R Rack mounting manual bypass USER'S MANUAL
14 SALICRU
: .............................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
15
: .............................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
BM-R Rack mounting manual bypass USER'S MANUAL
Avda. de la Serra 100
08460 Palautordera
BARCELONA
Tel. +34 93 848 24 00
Fax +34 93 848 22 05
services@salicru.com
SALICRU.COM
www.linkedin.com/company/salicru
@salicru_SA
Product Range
Uninterruptible Power Supplies (UPS)
Lighting Flow Dimmer-Stabilisers
DC Power Systems
Static Inverters
Photovoltaic Inverters
Voltage stabilisers
Variable frequency drives
The Technical Service and Support (T.S.S.) network, Com-
mercial network and warranty information are available in
website:
www.salicru.com
REF. EL106A01 REV. A CODE 401*