Table of Contents
- Before Using the Product
- Preparations
- Parts
- Installation
- Attaching the Stand (Type one) (C43J890DK* / C43J892DK*)
- Attaching the Stand (Type one) (C49J890DK* / C49J892DK*)
- Attaching the Stand (Type two) (C43J890DK* / C43J892DK*)
- Attaching the Stand (Type two) (C49J890DK* / C49J892DK*)
- Removing the Stand (For Attaching the BRACKET WALL) (C43J890DK* / C43J892DK*)
- Removing the Stand (For Attaching the BRACKET WALL) (C49J890DK* / C49J892DK*)
- Attaching the BRACKET WALL (C43J890DK* / C43J892DK*)
- Attaching the BRACKET WALL (C49J890DK* / C49J892DK*)
- Connecting and Using a Source Device
- Picture
- PIP/PBP
- OnScreen Display
- System
- Installing the Software
- Troubleshooting Guide
- Specifications
- Appendix
Samsung C43J892DKU User Manual
Displayed below is the user manual for C43J892DKU by Samsung which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
User Manual
The color and the appearance may differ depending on the product, and the specifications are subject to change without
prior notice to improve the performance.
The contents of this manual are subject to change without notice to improve quality.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Trademarks other than that of Samsung Electronics are owned by their respective owners.
C43J890DK* C43J892DK* C49J890DK* C49J892DK*
An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect (i.e., where the user
manual has not been read).
(b) You bring the unit to a repair center, but it is found that the product has no defect (i.e., where the user manual
has not been read).
You will be informed of the administration fee amount before a technician visits.
2
Table of contents
Before Using the Product
Securing the Installation Space 4
Precautions for storage 4
Safety Precautions 4
Cleaning 5
Electricity and Safety 5
Installation 6
Operation 7
Preparations
Parts 9
Control Panel 9
Direct Key guide 10
Function Key Guide 11
Changing Brightness, Contrast and Eye Saver Mode
settings 13
Changing the Volume setting 13
Types of Ports 14
Upgrading the Software via USB 15
Adjusting the Product Tilt and Height 17
Anti-theft Lock 18
Installation 19
Attaching the Stand (Type one) (C43J890DK* /
C43J892DK*) 19
Attaching the Stand (Type one) (C49J890DK* /
C49J892DK*) 20
Attaching the Stand (Type two) (C43J890DK* /
C43J892DK*) 21
Attaching the Stand (Type two) (C49J890DK* /
C49J892DK*) 22
Removing the Stand (For Attaching the BRACKET
WALL) (C43J890DK* / C43J892DK*) 23
Removing the Stand (For Attaching the BRACKET
WALL) (C49J890DK* / C49J892DK*) 24
Attaching the BRACKET WALL (C43J890DK* /
C43J892DK*) 25
Attaching the BRACKET WALL (C49J890DK* /
C49J892DK*) 26
Connecting and Using a Source Device
Read below before installing the monitor. 27
Connecting and Using a Source Device 27
Connection Using the HDMI Cable 27
Connection Using the DP Cable 28
Connection Using the USB Type-C Cable 28
Connecting to Headphones 29
Connecting the Product to a Source Device as a USB
Hub 29
Connecting a Source Device to the Product 29
Utilizing the Product as a USB HUB 30
Connecting the Power 31
Tidying Up the Connected Cables 32
Correct posture to use the product 33
Driver Installation 33
Setting Optimum Resolution 33
Picture
SAMSUNG MAGIC Bright 34
Brightness 35
Contrast 35
Sharpness 35
Color 35
SAMSUNG MAGIC Upscale 36
HDMI Black Level 36
Eye Saver Mode 36
Picture Size 37
Screen Adjustment 37
Calibration Report 37
3
Table of contents
PIP/PBP
PIP/PBP Mode 38
Size 39
Aspect Ratio 39
Position 40
Sound Source 40
Source 40
Switch USB 41
Picture Size 42
Contrast 43
OnScreen Display
Transparency 44
Position 44
Language 44
Display Time 44
System
USB Source Setup 45
DisplayPort Ver. 45
HDMI Mode 45
Smart ECO Saving 46
Off Timer Plus 46
PC/AV Mode 46
Source Detection 47
Key Repeat Time 47
Power LED On 47
Reset All 47
Information 47
Installing the Software
Easy Setting Box 48
Restrictions and Problems with the Installation 48
System Requirements 48
Troubleshooting Guide
Requirements Before Contacting Samsung Customer
Service Center 49
Testing the Product 49
Checking the Resolution and Frequency 49
Check the following. 49
Q & A 52
Specifications
General 53
Standard Signal Mode Table 54
Appendix
Responsibility for the Pay Service (Cost to
Customers) 57
Not a product defect 57
A Product damage caused by customer's fault 57
Others 57
Extended warranty 58
4
Securing the Installation Space
Ensure some space around the product for ventilation. An internal temperature rise may cause fire and
damage the product. Be sure to allow the amount of space as shown below or greater when installing
the product.
―The exterior may differ depending on the product.
10 cm (3.93 Inches)
10 cm
(3.93 Inches)
10 cm
(3.93 Inches)
10 cm (3.93 Inches)
10 cm
(3.93 Inches)
Precautions for storage
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used
nearby.
―Contact your nearest Samsung Customer Service Center if you want to clean the inside of the product
(Service fee will be charged.)
Do not press the monitor screen with hands or other objects. There is a risk of damaging the screen.
Safety Precautions
Warning A serious or fatal injury may result if instructions are not followed.
Caution Personal injury or damage to properties may result if instructions are
not followed.
Before Using the Product
Chapter 01
5
Cleaning
―Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
―Take the following steps when cleaning.
1
Power off the product and computer.
2
Disconnect the power cord from the product.
―Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric
shock may result.
3
Wipe the monitor with a clean, soft and dry cloth.
‒Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the monitor.
‒Do not spray water or detergent directly on the product.
4
Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
5
Connect the power cord to the product when cleaning is finished.
6
Power on the product and computer.
Electricity and Safety
Warning
•Do not use a damaged power cord or plug, or a loose power socket.
•Do not use multiple products with a single power socket.
•Do not touch the power plug with wet hands.
•Insert the power plug all the way in so it is not loose.
•Connect the power plug to a grounded power socket (type 1 insulated devices only).
•Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy
object.
•Do not place the power cord or product near heat sources.
•Clean any dust around the pins of the power plug or the power socket with a dry cloth.
Caution
•Do not disconnect the power cord while the product is being used.
•Only use the power cord provided with your product by Samsung. Do not use the power cord with
other products.
•Keep the power socket where the power cord is connected unobstructed.
‒The power cord must be disconnected to cut off power to the product when an issue occurs.
•Hold the plug when disconnecting the power cord from the power socket.
6
Warning
•DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT
INSTALL THE PRODUCT NEAR HEAT SOURCES.
•Do not install the product in poorly ventilated spaces such as a bookcase or closet.
•Install the product at least 10 cm away from the wall to allow ventilation.
•Keep the plastic packaging out of the reach of children.
‒Children may suffocate.
•Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
‒The product may fall and become damaged and/or cause an injury.
‒Using the product in an area with excess vibration may damage the product or cause a fire.
•Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or
smoke.
•Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
‒The product lifespan may be reduced or a fire may result.
•Do not install the product within the reach of young children.
‒The product may fall and injure children.
•Edible oil (such as soybean oil) may damage or distort the product. Keep the product away from oil
pollution. And do not install or use the product in the kitchen or near the kitchen stove.
Caution
•Do not drop the product while moving.
•Do not set down the product on its front.
•When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of
the product is not protruding.
‒The product may fall and become damaged and/or cause an injury.
‒Install the product only on cabinets or shelves of the right size.
•Set down the product gently.
‒Product failure or personal injury may result.
•Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical
substances, extreme temperatures or a significant presence of moisture, or a place where
the product will operate continuously for an extended period of time) may seriously affect its
performance.
‒Be sure to consult Samsung Customer Service Center if you want to install the product at such a
place.
Installation
7
Warning
•There is a high voltage inside the product. Never disassemble, repair or modify the product
yourself.
‒Contact Samsung Customer Service Center for repairs.
•To move the product, first disconnect all the cables from it, including the power cable.
•If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord
immediately and contact Samsung Customer Service Center.
•Do not let children hang from the product or climb on top of it.
‒Children may become injured or seriously harmed.
•If the product is dropped or the outer case is damaged, turn off the power and disconnect the
power cord. Then contact Samsung Customer Service Center.
‒Continued use can result in a fire or electric shock.
•Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
‒The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a
serious injury.
•During a lightning or thunderstorm, power off the product and remove the power cable.
•Do not drop objects on the product or apply impact.
•Do not move the product by pulling the power cord or any cable.
•If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area
immediately.
•Do not lift or move the product by pulling the power cord or any cable.
•Do not use or keep combustible spray or an inflammable substance near the product.
•Ensure the vents are not blocked by tablecloths or curtains.
‒An increased internal temperature may cause a fire.
•Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper,
matches, etc) into the product (via the vent or input/output ports, etc).
‒Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Center.
•Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the
product.
‒Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Center.
Operation
8
Caution
•Leaving the screen fixed on a stationary image for an extended period of time may cause
afterimage burn-in or defective pixels.
‒Activate power-saving mode or a moving-picture screen saver if you will not be using the
product for an extended period of time.
•Disconnect the power cord from the power socket if you do not plan on using the product for an
extended period of time (vacation, etc).
‒Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
•Use the product at the recommended resolution and frequency.
‒Your eyesight may deteriorate.
•Do not hold the product upside-down or move it by holding the stand.
‒The product may fall and become damaged or cause an injury.
•Looking at the screen too close for an extended period of time can deteriorate your eyesight.
•Do not use humidifiers or stoves around the product.
•Rest your eyes for more than 5 minutes or look at distance objects for every 1 hour of product use.
•Do not touch the screen when the product has been turned on for an extended period of time as it
will become hot.
•Store small accessories out of the reach of children.
•Exercise caution when adjusting the product angle or stand height.
‒Your hand or finger may get stuck and injured.
‒Tilting the product at an excessive angle may cause the product to fall and an injury may result.
•Do not place heavy objects on the product.
‒Product failure or personal injury may result.
•When using headphones or earphones, do not turn the volume too high.
‒Having the sound too loud may damage your hearing.
•Do not drop the product while moving.
‒Product failure or personal injury may result.
9
Preparations
Chapter 02
Parts
Control Panel
―The color and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Function Key Guide
Power LED
LEFT
JOG Button
RIGHT
UP(REAR)
DOWN(FRONT)
Shortcut Key
PRESS(ENTER)
PBP/PIPSource Switch USB
Return
Icons Description
Shortcut Key
PBP/PIPSource Switch USB
•Shortcut Key for Switching to a Source
This button is a shortcut for switching to a different source.
‒When the source is switched, the USB connection will be changed at the
same time according to the settings of USB Source Setup.
‒When PIP/PBP is On, only the source of the main screen can be switched.
•Shortcut Key for PIP/PBP On-Off
This button is a shortcut for the PIP/PBP On-Off function.
‒If there is no source for monitor, this button is disabled. The PIP/PBP On-
Off item is also disabled and appears dimmed in OSD.
•Shortcut Key for Switching USB
This button is a shortcut for switching a USB device to a different input
source.
‒The button is enabled only when PIP/PBP is On.
If you press this button when PIP/PBP is Off, the message Only applied
while PIP or PBP mode appears and nothing happens. Synchronously, The
Switch USB item in OSD is also disabled and appears dimmed.
‒If you press this button when PIP/PBP is On but there is no input source,
nothing happens.
JOG Button
Multi directional button that helps navigate.
―The JOG button is located at the bottom right side of the screen and has 5
directions of UP, DOWN, LEFT, RIGHT, and PRESS (ENTER).
10
Icons Description
Power LED
This LED is power status indicator and works as
•Power On (Power button): Off
•Power saving mode: Blinking
•Power Off (Power button): On
―The power Indicator operation can be swapped by changing in the menu. (System
→ Power LED On) Actual models because of functional variation maybe haven’t
this function.
Function Key Guide
Press the JOG button when the screen is turned on. The Function Key Guide will
appear. To access the onscreen menu when the guide is displayed, press the
corresponding direction button again.
―Function Key Guide may vary depending on the function or product model. Please
refer to the actual product.
Direct Key guide
―The shortcut button screen (OSD menu) shown below is displayed only when the monitor screen is turned
on, the computer resolution changes, or the input source changes.
―The function buttons page shows if Eye Saver Mode is enabled.
: On
: Off
Eye Saver Mode
Volume
Features
Eye Saver Mode Off
• / : Adjust Brightness, Contrast, Eye Saver Mode.
• : Adjust Volume.
• : Display Function Key Guide.
11
Function Key Guide
―To enter the main menu or to use other items, press the JOG button to display the Function Key Guide. You can exit by pressing the JOG button again.
Return
UP/DOWN/LEFT/RIGHT: Move to the item you want. The description for each item will appear when the focus changes.
PRESS(ENTER): The selected item will be applied.
Icons Description
Selects to change the input signal by moving the JOG button in the Function Key Guide screen. A message will appear on the top left corner of the screen if the input signal has
been changed.
Selects by moving the JOG button in the function key guide screen.
The OSD (On Screen Display) of your Monitor’s feature appears.
OSD control lock: Maintain the current settings, or lock the OSD control to prevent unintended changes to settings.
Enable/Disable: To lock/unlock the OSD control, press the LEFT button for 10 seconds when the main menu displayed.
―If the OSD control is locked, Brightness and Contrast can be adjusted. PIP/PBP is available.
Eye Saver Mode is available. Information can be viewed.
Selects by moving the JOG button in the function key guide screen.
Press the button when configuring settings for the PIP/PBP function is required.
Selects to turn the Monitor off by moving the JOG button in the function key guide screen.
―Actual models because of functional variation, Function key guide options will be different.
12
When the monitor displays nothing (i.e. Power saving mode or Non-signal mode), 2 direct keys for
control source and power could be used as below.
JOG Button Power saving/Non-signal mode
UP Source Change
Down
PRESS(ENTER) for 2 seconds Power Off
When the monitor displays the Main menu the JOG Button could be used as below.
JOG Button Action
UP/DOWN Move the option
LEFT
Exit the Main menu.
Close Sublist without saving value.
Value decreases in the slider.
RIGHT Move to next depth.
Value increases in the slider.
PRESS(ENTER) Move to next depth.
Save the value and close Sublist.
13
Changing Brightness, Contrast and Eye Saver Mode
settings
You can adjust Brightness, Contrast or Eye Saver Mode by moving the JOG button up or down, if no
OSD menu is displayed.
Eye Saver Mode
Brightness
Contrast
Off
―The displayed image may differ depending on the model.
―The default brightness can vary depending on the region.
Eye Saver Mode
Brightness
―This menu is not available when Smart ECO Saving is enabled.
―This menu is not available when Eye Saver Mode is enabled.
Contrast
―This menu is not available when
SAMSUNG
MAGIC
Bright is set to Cinema mode.
―This menu is not available when PIP/PBP Mode is set to On and the Size is set to (PBP Mode).
Changing the Volume setting
You can adjust Volume by moving the JOG button left or right, if no OSD menu is displayed.
Volume 50
Mute
―The displayed image may differ depending on the model.
―If the audio quality of a connected input device is poor, the Auto Mute function on the product may mute
the sound or cause choppy audio when applying the headphones or speakers. Set the input volume for the
input device to at least 20% and control the volume using the volume control (JOG button LEFT/RIGHT) on
the product.
―What is Auto Mute?
The function mutes the audio to improve sound effect when there is sound noise or when the input
signal is weak, usually due to a problem with the volume of an input device.
―To activate the Mute function, access the Volume control screen, then use the JOG button to move the
focus down. To deactivate the Mute function, access the Volume control screen, then increase or decrease
the Volume.
14
Types of Ports
―The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
POWER IN
Port Description
POWER IN
Connect the power cord for your monitor to the POWER IN port on the
back of the product.
Connects to a source device using an HDMI cable or HDMI-DVI cable.
Connects to a PC using a DP cable.
Connects to a source device using a USB Type-C cable. Compatible with
a USB cable version 3.0 or lower.
Connects to a PC using a USB cable.
―This port can only connect to a PC.
Port Description
Connect to a USB device. These ports are enabled when a source device
is connected to or using a USB Type-C to A cable or
a USB Type-C cable. These ports are enabled when a source device is
connected to using a USB Type-C to A cable.
Connect to a USB device. This port is enabled when a source device is
connected to or using a USB Type-C to A cable or a USB
Type-C cable. This port is enabled when a source device is connected to
using a USB Type-C to A cable. And USB 3.0 is supported only
when a source device is connected to or using a USB
Type-C to A (3.0) cable.
Connect to an audio output device such as headphones.
Dedicated to service technicians.
15
Upgrading the Software via USB
1
Be sure to insert the USB disk into the USB port marked out with the blue box as shown in the
figure below. You can upgrade the software via USB only if either the monitor screen operates
normally or the check signal is displayed on the monitor screen.
USB
Check Signal Cable
HDMI
When the screen as shown in the following figure is displayed, press and hold the Down arrow key
for 5 seconds.
Power Off
2
When the message as shown in the following figure is displayed on the monitor, select Yes to
upgrade the software.
Do you want to update via USB?
YesNo
3
When the screen as shown in the following figure is displayed, select Yes.
Update from version 0802.0 to version 0803.0
Update now
YesNo
4
The software upgrading proceeds.
Updating product Software...
Your product will turn itself off and on again
automatically after completing update.
Update now
0%
16
Note
1
Before upgrading through USB disk, you need to format the USB disk into the FAT32 format.
2
Make sure only the BIN file for upgrade is in the USB disk.
3
For the CJ89 model, make sure each upgrade file is in the BIN formate and follow the naming
rules of CJ89 (m-J89**CGAA-****.*[4-digit number].bin), wherein ** indicates the monitor size in
inches, ****.* stands for the version number and the 4-digit number is the checksum. For example,
“m-J8949CGAA-1000.0[9A80].bin” follows the naming rules of CJ89 49'' model, and must be
copied to the root directory.
4
If you want to keep the current version or degrade to a lower version, you may change file name to
m-J89**CGAA-0000.0[4-digit number] and then perform the same operations.
5
If the No valid update files found. Please check your USB device and try again. message is
displayed, this is probably due to the following reasons.
No valid update files found.
Please check your USB device and try again.
Update now
YesNo
‒No USB disk is inserted into the USB port marked out with the blue box.
‒The USB disk format is not supported.
‒The USB disk contains no valid upgrade files. (No upgrade files exist, or the file names are
incorrect.)
6
Do not turn off the monitor. And prevent the upgrading from any interruption as far as possible. If
an interruption happens, the monitor will return to the production version.
―Note that the production version may not be the same as the version before this upgrading if some other
upgrading has been done earlier.
17
Adjusting the Product Tilt and Height
―The color and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
-15.0° (±2.0°) to Left ~ 15.0° (±2.0°) to Right
C43J890DK* / C43J892DK*: -2.0° (±2.0°) ~ 17.0° (±2.0°)
C49J890DK* / C49J892DK*: -2.0° (±2.0°) ~ 15.0° (±2.0°)
0 ~ 120.0 mm (±5.0 mm)
•The monitor tilt and height can be adjusted.
•When adjusting the tilt and height, hold both sides of the product and avoid using excessive force
to prevent damage.
•When adjusting the stand height, you may hear a noise. This noise is generated because the ball
inside the stand slides when the stand height is adjusted. It is a normal noise and not a product
malfunction.
Caution
•Grasp the left and right sides of the monitor and adjust the tilt.
After adjusting the product tilt and height, if the screen is not level, take the following actions.
+4˚
-4˚
•Hold the bezel at both side edges and adjust the monitor angle until the screen becomes level. (Be
careful not to directly hold the LCD display.)
•The monitor angle can be adjusted from -4° to +4°.
18
Anti-theft Lock
―An anti-theft lock allows you to use the product securely even in public places.
―The locking device shape and locking method depend on the manufacturer. Refer to the user guide
provided with your anti-theft locking device for details.
To lock an anti-theft locking device:
1
Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2
Put one end of the cable through the loop on the other end.
3
Insert the locking device into the anti-theft lock slot at the back of the product.
4
Lock the locking device.
‒An anti-theft locking device can be purchased separately.
‒Refer to the user guide provided with your anti-theft locking device for details.
‒Anti-theft locking devices can be purchased at electronics retailers or online.
19
Installation
Attaching the Stand (Type one) (C43J890DK* / C43J892DK*)
―Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
: The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it.
―There is a risk of scratch damage if the screwdriver comes in contact with the product surface while fastening the screws. Make sure the screwdriver does not touch the surface.
1
11
21
3
Caution
Hold the stand neck with both
hands, not one hand, to prevent it
from falling off and causing injury.
Remove the Cushion Top and Cushion Front,
and then place the Cushion Front on the desk.
Pull the monitor out of the
package (two people are required
for this work), and then place the
monitor on the Cushion Front.
Place the stand neck on the
monitor as shown in the figure.
Caution
Tilt the stand neck to sides to avoid contact
with the screwdriver.
1
41
51
61
7
Fasten the screws at the top of the
stand neck.
Insert the stand base into the stand neck in
the direction as shown in the figure.
Assemble the COVER-CLEAN BACK
STAND to the stand neck as shown
in the figure.
Push the COVER-CLEAN BACK
STAND in the direction as shown in
the figure.
20
Attaching the Stand (Type one) (C49J890DK* / C49J892DK*)
―Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
: The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it.
―There is a risk of scratch damage if the screwdriver comes in contact with the product surface while fastening the screws. Make sure the screwdriver does not touch the surface.
1
11
21
3
Caution
Hold the stand neck with both hands, not one hand, to
prevent it from falling off and causing injury.
Remove the Cushion Top and Cushion Front, and then
place the Cushion Front on the desk.
Pull the monitor out of the package (two
people are required for this work), and then
place the monitor on the Cushion Front.
Place the stand neck on the monitor as
shown in the figure.
1
41
51
6
Caution
Tilt the stand neck to sides to avoid contact with the
screwdriver.
Fasten the screws at the top of the stand neck. Insert the stand base into the stand neck in
the direction as shown in the figure.
Disassemble the COVER-REAR TOP.
1
71
8
Assemble the COVER-REAR TOP to the stand neck as
shown in the figure.
Rotate the COVER-REAR TOP clockwise.
21
Attaching the Stand (Type two) (C43J890DK* / C43J892DK*)
―Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
: The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it.
―There is a risk of scratch damage if the screwdriver comes in contact with the product surface while fastening the screws. Make sure the screwdriver does not touch the surface.
1
11
2
Caution
Hold the stand neck with both hands, not one
hand, to prevent it from falling off and causing
injury.
Place the stand neck on the monitor as shown
in the figure.
Caution
Tilt the stand neck to sides to avoid contact with the
screwdriver.
Fasten the screws at the top of the stand neck.
1
31
41
51
6
Insert the stand base into the stand neck in the
direction as shown in the figure.
Assemble the COVER-CLEAN BACK STAND to
the stand neck as shown in the figure.
Push the COVER-CLEAN BACK STAND in the direction
as shown in the figure.
Stand up the monitor as shown in the figure.
1
7
Remove the package.
22
Attaching the Stand (Type two) (C49J890DK* / C49J892DK*)
―Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
: The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it.
―There is a risk of scratch damage if the screwdriver comes in contact with the product surface while fastening the screws. Make sure the screwdriver does not touch the surface.
1
11
2
Caution
Hold the stand neck with both hands, not one
hand, to prevent it from falling off and causing
injury.
Place the stand neck on the monitor as shown
in the figure.
Caution
Tilt the stand neck to sides to avoid contact with the
screwdriver.
Fasten the screws at the top of the stand neck.
1
31
41
51
6
Insert the stand base into the stand neck in the
direction as shown in the figure.
Disassemble the COVER-REAR TOP. Assemble the COVER-REAR TOP to the stand neck as
shown in the figure.
Rotate the COVER-REAR TOP clockwise.
1
71
8
Stand up the monitor as shown in the figure. Remove the package.
23
Removing the Stand (For Attaching the BRACKET WALL) (C43J890DK* / C43J892DK*)
―Before removing the stand from the monitor, place the monitor on a flat and stable surface with the screen facing down.
: The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it.
1
1
234
Disassemble the COVER-CLEAN BACK STAND
with a thin stick, as shown in the figure.
Disassemble the COVER-CLEAN BACK STAND. Remove the COVER-CLEAN BACK STAND. Remove the stand base from the stand neck.
56
Unfasten the 4 screws at the top of the stand
neck.
Lift and remove the stand. Caution
Do not press down on the monitor. There is a risk
of damaging the monitor.
24
Removing the Stand (For Attaching the BRACKET WALL) (C49J890DK* / C49J892DK*)
―Before removing the stand from the monitor, place the monitor on a flat and stable surface with the screen facing down.
: The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it.
1234
Rotate the COVER-REAR TOP counterclockwise. Lift the COVER-REAR TOP. Disassemble the COVER-REAR TOP. Remove the stand base from the stand neck.
56
Unfasten the 4 screws at the top of the stand
neck.
Lift and remove the stand. Caution
Do not press down on the monitor. There is a risk
of damaging the monitor.
25
Attaching the BRACKET WALL (C43J890DK* /
C43J892DK*)
―Power the product off and remove the power cable from the power socket.
1 2
43
Attach the BRACKET WALL here
BRACKET WALL
Align with on the monitor, then tightly fasten with the screws removed from the stand (P. 23).
•Notes
‒Using a screw longer than the standard length can damage the internal components of the
product.
‒The length of screws required for a wall mount that does not comply with the VESA standards
may vary depending on the specifications.
‒Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit
or desktop stand using excessive force. The product may get damaged or fall and cause personal
injury. Samsung shall not be held liable for any damage or injury caused by using improper
screws or attaching the wall-mount kit or desktop stand using excessive force.
‒Samsung shall not be held liable for any product damage or personal injury caused by using a
wall-mount kit other than the one specified or from an attempt to install the wall-mount kit on
your own.
‒To mount the product on a wall, ensure you purchase a wall-mount kit that can be installed 10
cm or farther away from the wall.
‒Be sure to use a wall-mount kit that complies with the national standards.
‒To install the monitor using a wall mount, disconnect the stand base from the monitor.
Unit: mm (inches)
Model name VESA screw hole specs (A * B)
in millimeters
Standard Screw Quantity
C43J890DK* /
C43J892DK* 100.0 x 100.0 (3.9 x 3.9) 4.0 mm Φ, 0.7 pitch * 10.0 mm long 4 EA
―Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to
electric shock.
26
Attaching the BRACKET WALL (C49J890DK* /
C49J892DK*)
―Power the product off and remove the power cable from the power socket.
1 2
43
Attach the BRACKET WALL here
BRACKET WALL
Align with on the monitor, then tightly fasten with the screws removed from the stand (P. 24).
•Notes
‒Using a screw longer than the standard length can damage the internal components of the
product.
‒The length of screws required for a wall mount that does not comply with the VESA standards
may vary depending on the specifications.
‒Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit
or desktop stand using excessive force. The product may get damaged or fall and cause personal
injury. Samsung shall not be held liable for any damage or injury caused by using improper
screws or attaching the wall-mount kit or desktop stand using excessive force.
‒Samsung shall not be held liable for any product damage or personal injury caused by using a
wall-mount kit other than the one specified or from an attempt to install the wall-mount kit on
your own.
‒To mount the product on a wall, ensure you purchase a wall-mount kit that can be installed 10
cm or farther away from the wall.
‒Be sure to use a wall-mount kit that complies with the national standards.
‒To install the monitor using a wall mount, disconnect the stand base from the monitor.
Unit: mm (inches)
Model name VESA screw hole specs (A * B)
in millimeters
Standard Screw Quantity
C49J890DK* /
C49J892DK* 100.0 x 100.0 (3.9 x 3.9) 4.0 mm Φ, 0.7 pitch * 10.0 mm long 4 EA
―Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to
electric shock.
27
Connecting and Using a Source Device
Chapter 03
Read below before installing the monitor.
1
Check the shapes of both ends of the cables that came with the monitor, and check the shapes and
positions of the matching ports on the monitor and external devices.
2
Before connecting signal cables, disconnect the power cables for the monitor and external devices
from the power outlet to prevent device damage from a short circuit or overcurrent.
3
After connecting all signal cables, connect the power cables for the monitor and external devices
to the power outlet.
4
Read the user manual to familiarize yourself with the monitor functions, precautions, and proper
use, before using the installed monitor.
Connecting and Using a Source Device
Select a connection method suitable for your source device.
―Connecting parts may differ in different products.
―Provided ports may vary depending on the product.
Connection Using the HDMI Cable
Check to make sure that the power cables for the monitor and external devices, such as
computers and set-top boxes, are not connected to the power outlet.
HDMI IN
―When connecting an HDMI cable, use the cable that came with the components of the monitor. If you use
an HDMI cable other than provided by Samsung, the image quality may be degraded. A Samsung branded
cable is recommended.
28
Connection Using the DP Cable
Check to make sure that the power cables for the monitor and external devices, such as
computers and set-top boxes, are not connected to the power outlet.
―When connecting a DP cable, use Samsung branded cable. If you use a DP cable other than provided by
Samsung, the image quality may be degraded.
Connection Using the USB Type-C Cable
Check to make sure that the power cables for the monitor and external devices, such as
computers and set-top boxes, are not connected to the power outlet.
The port is the dedicated USB hub port. For display on the screen, use the
, port.
The USB Type-C port can support USB Power Delivery, Data, and DP video signal.
According to the USB Power Delivery 3.0 specification, the monitor can charge your notebook or mobile
phone when you connect it to the monitor with a USB Type-C cable.
―For , a maximum charging power of 15 W is supported. For , a maximum charging power
of 95 W is supported. So, is proper for a mobile phone and is proper for a notebook.
Charging speed may vary depending on the notebook or mobile phone connected to the monitor.
―Because notebooks and mobile phones with a USB Type-C port released on the market are very various,
we cannot guarantee that the monitor can charge all types of notebooks and mobile phones with a USB
Type-C port.
―Make sure that the USB Type-C cable complies with the USB PD specification. Otherwise, your devices may
be damaged. A Samsung branded cable is recommended.
29
Connecting to Headphones Connecting the Product to a Source Device as
a USB Hub
Connecting a Source Device to the Product
―The product can function as a USB hub when it is connected to a source device via a USB Type-C cable or
USB Type-C to A cable. Then you can connect USB devices to the product without having to directly connect
them to the source device, and then you can control the USB devices from the product.
To use the product as a USB hub, connect a source device to the product using a USB Type-C cable or
USB Type-C to A cable.
Connect the USB cable to on the back of the product and to or on the source device.
30
Utilizing the Product as a USB HUB
Using the product as a hub, connect and use various source devices with the product at the same time.
A source device cannot connect to multiple devices at the same time if it has a limited number of available input/output ports. In this case, the hub feature of the product will improve your work efficiency by
allowing you to connect multiple devices to the USB ports on the product at the same time without directly connecting them to a source device.
If multiple devices are connected to a source device, the many cables around the source device may look messy. Connecting the devices directly to the product will resolve such inconvenience.
Connect a mobile device such as an MP3 player or smartphone to the product connected to a source device. This allows you to control the device or charge the device battery from your PC.
―To detect and start a USB device faster, connect the device to the USB 3.0 port on the product. The read/write rate is affected by the USB device and your source device.
―The product does not support media play. If you need to play a file on your USB device, connect the product as a USB hub to your source device, and then play the file on your source device.
―For USB-related problems caused by OS, drive programs or software, please contact relevant suppliers.
―With the launch of various USB devices on the market, we cannot guarantee that our products are matched with all USB devices.
―For an external mass-storage HDD requiring external power supply, be sure to connect it to a power source.
―The battery can be charged in the power-saving mode, but it cannot be charged when the product is powered off.
―Charging your USB device is not possible if the power cable is disconnected from the power socket.
―The USB device needs to be purchased separately.
31
Connecting the Power
POWER IN
To use the product, connect the power cable to a power outlet and the POWER IN port on the product.
―The input voltage is switched automatically.
32
Tidying Up the Connected Cables
: Headphones hanger
: Downward
: Upward
12345
Connect the corresponding cables. Arrange the cables against the bend
tendency of the cables and pull the
cables out of the COVER-REAR SUB
grooves.
Hang the HOLDER-CABLE in the
direction as shown in the figure.
Arrange the cables against their bend
tendency, and then pull them through
the HOLDER-CABLE hangers. When
the set height is changed, you need
to arrange the cables and pull them
through the HOLDER-CABLE hangers
again.
Push the COVER STAND BODY REAR in
the direction as shown in the figure.
678910
Remove the COVER STAND BODY REAR
by pulling it in the direction as shown in
the figure.
Place the corresponding cables into
the stand-neck holder. Do not stretch
the cable. Three cables in one holder is
recommended.
Attach the COVER STAND BODY REAR in
the direction as shown in the figure with
the buckles not being exposed.
Move down the COVER STAND BODY
REAR until it covers the stand neck
completely.
Adjust the set height, if required.
11 12 13
Open the Headset Hanger by pushing it
down.
Hang the headset. Rotate and then push up the Headset
Hanger in the directions as shown in the
figure.
Caution
Open the COVER-REAR SUB in the
direction as shown in the figure.
33
Correct posture to use the product
Use the product in the correct posture as follows:
•Straighten your back.
•Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at
the screen.
•Keep your eyes directly in front of the screen.
•Adjust the angle so light does not reflect on the screen.
•Keep your forearms perpendicular to your upper arms and level with the back of your hands.
•Keep your elbows at about a right angle.
•Adjust the height of the product so you can keep your knees bent at 90 degrees or more, your heels
attached to the floor, and your arms lower than your heart.
•Do the Eye excercises or blink frequently, then eye fatigue will be relieved.
Driver Installation
―You can set the optimum resolution and frequency for this product by installing the corresponding drivers.
―To install the latest version of the product driver, download it from the Samsung Electronics website at
http://www.samsung.com.
Setting Optimum Resolution
An information message about setting optimum resolution will appear if you power on the product for
the first time after purchase.
Select a language on the product and change the resolution on your PC to the optimum setting.
―If the optimum resolution is not selected, the message will appear up to three times for a specified time
even when the product is turned off and on again.
―The optimum resolution can also be selected in Control Panel on your PC.
34
Picture
A detailed description of each function is provided. Refer to your product for details.
Chapter 04
―The functions available may vary depending on the product model. The color and shape of parts may differ
from what is shown. Specifications are subject to change without notice to improve quality.
SAMSUNG MAGIC Bright
This menu provides an optimum picture quality suitable for the environment where the product will be
used.
―This menu is not available when Smart ECO Saving is enabled.
―This menu is not available when Eye Saver Mode is enabled.
―Not available when PIP/PBP Mode is set to On.
You can customize the brightness to suit your preferences.
In PC mode
•Custom: Customize the contrast and brightness as required.
•Standard: Obtain a picture quality suitable for editing documents or using Internet.
•Cinema: Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD content.
•High-brightness: Maximize the screen brightness.
In AV mode
When the external input is connected through HDMI/DP/USB Type-C and PC/AV Mode is set to AV,
SAMSUNG
MAGIC
Bright has four automatic picture settings (Dynamic, Standard, Movie and Custom) that are
preset at the factory. You can activate either Dynamic, Standard, Movie or Custom. You can select
Custom which automatically recalls your personalized picture settings.
•Dynamic: Select this mode to view a sharper image than in Standard mode.
•Standard: Select this mode when the surroundings are bright. This also provides a sharp image.
•Movie: Select this mode when the surroundings are dark. This will save power and reduce eye
fatigue.
•Custom: Select this mode when you want to adjust the image according to your preferences.
35
Brightness
You can adjust the general brightness of the picture. (Range: 0~100)
A higher value will make the picture appear brighter.
―This menu is not available when Smart ECO Saving is enabled.
―This menu is not available when Eye Saver Mode is enabled.
Contrast
Adjust the contrast between the objects and background. (Range: 0~100)
A higher value will increase the contrast to make the object appear clearer.
―This menu is not available when
SAMSUNG
MAGIC
Bright is set to Cinema mode.
―This menu is not available when PIP/PBP Mode is set to On and the Size is set to (PBP Mode).
Sharpness
Make the outline of objects more clear or blurry. (Range: 0~100)
A higher value will make the outline of objects clearer.
―This menu is not available when
SAMSUNG
MAGIC
Bright is set to Cinema mode.
―This menu is not available when
SAMSUNG
MAGIC
Upscale is in Mode1 or Mode2 mode.
―Not available when PIP/PBP Mode is set to On.
Color
Adjust the tint of the screen.
―This menu is not available when
SAMSUNG
MAGIC
Bright is set to Cinema mode.
―This menu is not available when Eye Saver Mode is enabled.
―Not available when PIP/PBP Mode is set to On.
•Red: Adjust the red saturation level. Values closer to 100 mean greater intensity for the color.
•Green: Adjust the green saturation level. Values closer to 100 mean greater intensity for the color.
•Blue: Adjust the blue saturation level. Values closer to 100 mean greater intensity for the color.
•Color Tone: Select a color tone that best suits your viewing needs.
‒Cool 2: Set the color temperature to be cooler than Cool 1.
‒Cool 1: Set the color temperature to be cooler than Normal mode.
‒Normal: Display the standard color tone.
‒Warm 1: Set the color temperature to be warmer than Normal mode.
‒Warm 2: Set the color temperature to be warmer than Warm 1.
‒Custom: Customize the color tone.
―When the external input is connected through HDMI/DP/USB Type-C and PC/AV Mode is set to AV, Color
Tone has four color temperature settings (Cool, Normal, Warm and Custom).
•Gamma: Adjust the middle level of luminance.
‒Mode1 / Mode2 / Mode3
36
SAMSUNG MAGIC Upscale
SAMSUNG
MAGIC
Upscale function can enhance the layers of the picture details and the vividness of the picture.
The function has more obvious effects on low-resolution pictures.
―This menu is not available when
SAMSUNG
MAGIC
Bright is set to Cinema mode.
―Not available when PIP/PBP Mode is set to On.
•Off / Mode1 / Mode2
―Comparing with Mode1, Mode2 has a stronger effect.
HDMI Black Level
If a DVD player or set-top box is connected to the product via HDMI, image quality degradation (contrast/
color degradation, black level, etc.) may occur, depending on the connected source device.
In such case, HDMI Black Level can be used to adjust the image quality.
―This function is only available in HDMI mode.
―Not available when PIP/PBP Mode is set to On.
•Normal: Select this mode when there is no contrast ratio degradation.
•Low: Select this mode to reduce the black level and increase the white level when there is a
contrast ratio degradation.
―HDMI Black Level may not be compatible with some source devices.
―The HDMI Black Level feature is only activated at a certain AV resolution, such as 720P and 1080P.
Eye Saver Mode
Set to an optimum picture quality suitable for eye relaxation.
TÜV Rheinland “Low Blue Light Content” is a certification for products which meet requirements for
lower blue light levels. When Eye Saver Mode is 'On', the blue light that wavelength is around 400nm
will decrease, and it will provide an optimum picture quality suitable for eye relaxation. At the same
time, the blue light level is lower than in the default settings, and it was tested by TÜV Rheinland and
certified as it met the requirements of TÜV Rheinland “Low Blue Light Content” standards.
37
Picture Size
Change the picture size.
―This menu is not available when PIP/PBP Mode is set to On and the Size is set to (PBP Mode).
In PC mode
•Auto: Display the picture according to the aspect ratio of the input source.
•Wide: Display the picture in full screen regardless of the aspect ratio of the input source.
In AV mode
•4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
•16:9: Display the picture with an aspect ratio of 16:9.
•Screen Fit: Display the picture with the original aspect ratio without cutting off.
―The function may not be supported depending on the ports provided with the product.
―Changing the screen size is available when the following conditions are satisfied.
―A digital output device is connected using the HDMI/DP/USB Type-C cable.
―The input signal is 480p, 576p, 720p, or 1080p and monitor can display normally (Not every model can
support all of these signals.).
―This can only be set when the external input is connected through HDMI/DP/USB Type-C and PC/AV
Mode is set to AV.
Screen Adjustment
―This menu is only available when Picture Size is set to Screen Fit in AV Mode.
When a 480P or 576P or 720P or 1080P signal is input in AV mode and the monitor can display normally,
select Screen Fit to adjust horizontal position in 0-6 levels.
Configuring H-Position & V-Position
H-Position: Move the screen to the left or right.
V-Position: Move the screen up or down.
Calibration Report
The data from this report are measured at the time of shipment.
•The measurements may vary according to the measuring equipment, measuring location, system
environment (e.g. computer, graphic board, etc) and other variables.
•Input signal: HDMI
•Each measurement from this report is based on the Custom mode at the time of shipment.
•This report is not provided on the menu of some products, but in an separate hardcopy report
instead.
38
PIP/PBP
A detailed description of each function is provided. Refer to your product for details.
Chapter 05
―The functions available may vary depending on the product model. The color and shape of parts may differ
from what is shown. Specifications are subject to change without notice to improve quality.
PIP/PBP Mode
Enable or disable the PIP/PBP Mode function.
The PIP (Picture in Picture) function separates the screen into two parts. One source device is displayed
on the main screen at the same time the another source device is displayed in inset windows.
The PBP (Picture by Picture) function separates the screen in half displaying output from two different
source devices simultaneously on the left and right sides of the screen.
―DisplayPort and USB Type-C 1 cannot be selected as input sources at the same time.
―PIP/PBP mode is compatible with Windows 7, Windows 8, and Windows 10.
―The PIP/PBP function may not be available depending on the specifications of the graphics card used. If the
screen is blank in PIP/PBP mode when the optimum resolution is selected, go to Control Panel → Display →
Screen Resolution and click Detect on the PC. (Instructions are based on Windows 7.)
―The screen may flicker briefly or appear after a delay when you enable or disable the PIP/PBP function or
when you change the screen size with the PIP/PBP function activated.
This can typically arise when a PC and a monitor are connected to two or more input sources. It has nothing
to do with the performance of a monitor.
The issue is mainly caused when the video signals are delayed in transmission to the monitor depending on
the graphics card performance.
―To maximize the picture quality, it is recommended to use a graphics card that supports DFHD (3840 x
1080, 3840 x 1200) resolution.
―When using PIP/PBP, automatic switching to the optimum resolution and frequency is not available, due
to conformance with the graphics card and Windows. Set PIP/PBP Mode to Off. Alternatively, restart the
monitor, then set the resolution to the optimum setting using the Windows interface.
39
Size
Select the size and aspect ratio of the sub-screen.
C43J890DK* / C43J892DK*
•: Select the icon image if you want to use PBP mode where the optimum resolution for the left
and right sides of the screen is 1920 x 1200 (width x height).
•: Select the icon image if you want to use PIP mode where the optimum resolution for the sub-
screen is 720 x 480 (width x height).
•: Select the icon image if you want to use PIP mode where the optimum resolution of the sub-
screen is 1280 x 720 (width x height).
C49J890DK* / C49J892DK*
•: Select the icon image if you want to use PBP mode where the optimum resolution for the left
and right sides of the screen is 1920 x 1080 (width x height).
• : Select the icon image if you want to use PIP mode where the optimum resolution for the
subscreen is 720 x 480 (width x height).
•: Select the icon image if you want to use PIP mode where the optimum resolution of the
subscreen is 1280 x 720 (width x height).
Aspect Ratio
Select the image size for each screen.
C43J890DK* / C43J892DK*
•16:10(16:10): Select this option if you want to use PBP mode where the optimum resolution for the
left and right sides of the screen is 1920 x 1200 (width x height).
•21:10(11:10): Select this option if you want to use PBP mode where the optimum resolution for the
left side of the screen is 2520 x 1200 (width x height) and the optimum resolution for the right side
of the screen is 1320 x 1200 (width x height).
•11:10(21:10): Select this option if you want to use PBP mode where the optimum resolution for the
left side of the screen is 1320 x 1200 (width x height) and the optimum resolution for the right side
of the screen is 2520 x 1200 (width x height).
C49J890DK* / C49J892DK*
•16:9(16:9): Select this option if you want to use PBP mode where the optimum resolution for the
left and right sides of the screen is 1920 x 1080 (width x height).
•21:9(11:9): Select this option if you want to use PBP mode where the optimum resolution for the
left side of the screen is 2560 x 1080 (width x height) and the optimum resolution for the right side
of the screen is 1280 x 1080 (width x height).
•11:9(21:9): Select this option if you want to use PBP mode where the optimum resolution for the
left side of the screen is 1280 x 1080 (width x height) and the optimum resolution for the right side
of the screen is 2560 x 1080 (width x height).
40
Position
Select the position of the sub-screen from the available options.
• / / /
―Not available when PBP is selected.
―The screen may flicker if the input signal is unstable.
Sound Source
Set which screen you want to hear the sound for.
PIP mode
/
PBP mode
/
Source
Select the source for each screen.
PIP Mode (available in PIP mode(Size / ))
―The input source for the main screen changes.
―With the exception of the current input source, the other two input sources can be selected.
―The screen may flicker if the input signal is unstable.
―When the Function Key Guide appears, move the JOG button LEFT to select the icon and then press the
JOG button. The main screen will switch in the order HDMI → DisplayPort → USB Type-C 1 → USB Type-C 2.
PBP Mode (available in PBP mode(Size ))
―The input source for the main screen changes.
―The screen may flicker if the input signal is unstable.
―When the input signal of the left and right screens are the same, the operation cannot be performed.
―When the Function Key Guide appears, move the JOG button LEFT to select the icon and then press the
JOG button. The same PBP source setting menu appears.
41
Switch USB
DP IN
HDMI IN
PC
Monitor
Laptop
PC Screen Laptop/Mobile Phone
Screen
HDMI Cable
USB Cable
DP Cable
USB Type-C Cable
The KVM (keyboard, video, and mouse) switch enables users to use only a keyboard, a video monitor, and a mouse for controlling multiple input sources.
The function of the Samsung USB switch is as follows:
•When PIP/PBP of a Samsung monitor is on, USB devices (I/O device, USB storage device, etc.) connected to the monitor can be switched between different input sources using the USB switch.
‒Two different input sources must be connected to the monitor via source ports (HDMI, DP, USB-C#1, USB-C#2), and an upstream USB hub must be correctly connected to the monitor if required.
‒You must connect USB devices to the Samsung monitor, enable PIP/PBP, and then correctly set up USB hub assignment in the OSD.
•This function can be operated using the USB Switch Shortcut key or the USB Switch item in OSD.
―Each of USB-C#1 and USB-C#2 can be regarded as an upstream USB hub as well as an input source. Therefore, it is unnecessary to set up USB hub assignment for these two ports.
This option is for switching a USB device to a different input source.
―The option is disabled and appears dimmed if PIP/PBP is Off.
―When a USB device is switched to a source, information about the source including the USB hub port is displayed on the screen.
―The Keyboard and Mouse (KM) switch enables users to interact with and manage up to three input sources using a single mouse and keyboard.
―To prevent data damage or loss, make sure that, before performing Switch USB, no USB storage devices are being used by the input sources connected to the monitor.
Mobile Phone
USB Type-C Cable
42
Picture Size
PIP Mode (available in PIP mode (Size / ))
Select the image size for sub-screen.
In PC mode
•Auto: Display the picture according to the aspect ratio of the each screen input source.
•Wide: Display the picture in full screen regardless of the aspect ratio of the each screen input
source.
In AV mode
•4:3: Display the picture of the sub-screen with an aspect ratio of 4:3. Suitable for videos and
standard broadcasts.
•16:9: Display the picture with an aspect ratio of 16:9.
•Screen Fit: Display the picture of the sub-screen with the original aspect ratio without cutting
anything off.
―The function may not be supported depending on the ports provided with the product.
―Changing the screen size is available when the following conditions are satisfied.
―A digital output device is connected using the HDMI/DP/USB Type-C cable.
―The input signal is 480p, 576p, 720p, or 1080p and monitor can display normally (Not every model can
support all of these signals.).
―This can only be set when the external input is connected through HDMI/DP/USB Type-C and PC/AV
Mode is set to AV.
PBP Mode (available in PBP mode(Size ))
Set the Picture Size for each of the divided screens.
In PC mode
•Auto: Display the picture according to the aspect ratio of the each screen input source.
•Wide: Display the picture in full screen regardless of the aspect ratio of the each screen input
source.
In AV mode
•4:3: Display the picture of the sub-screen with an aspect ratio of 4:3. Suitable for videos and
standard broadcasts.
•16:9: Display the picture with an aspect ratio of 16:9.
•Screen Fit: Display the picture of the sub-screen with the original aspect ratio without cutting
anything off.
―The function may not be supported depending on the ports provided with the product.
―Changing the screen size is available when the following conditions are satisfied.
―A digital output device is connected using the HDMI/DP/USB Type-C cable.
―The input signal is 480p, 576p, 720p, or 1080p and monitor can display normally (Not every model can
support all of these signals.).
―This can only be set when the external input is connected through HDMI/DP/USB Type-C and PC/AV
Mode is set to AV.
43
Contrast
PIP Mode (available in PIP mode(Size / ))
Adjust the contrast level for sub-screen.
PBP Mode (available in PBP mode(Size ))
Adjust the contrast level for each screen.
44
OnScreen Display
A detailed description of each function is provided. Refer to your product for details.
Chapter 06
―The functions available may vary depending on the product model. The color and shape of parts may differ
from what is shown. Specifications are subject to change without notice to improve quality.
Transparency
Set the transparency for the menu windows.
Position
Adjust the menu position.
Language
Set the menu language.
―A change to the language setting will only be applied to the onscreen menu display.
―It will not be applied to other functions on your PC.
Display Time
Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified
period of time.
Display Time can be used to specify the time after which you want the OSD menu to disappear.
45
System
A detailed description of each function is provided. Refer to your product for details.
Chapter 07
―The functions available may vary depending on the product model. The color and shape of parts may differ
from what is shown. Specifications are subject to change without notice to improve quality.
USB Source Setup
This option is for assigning correct USB ports for HDMI and DP ports.
―You must assign a correct USB port for each input source to ensure that the USB Switch function works
properly.
―USB-C#1 and USB-C#2 can be regarded as input sources and USB ports. Therefore, it is not necessary to set
up them. The last USB port can only work as a USB port but not as an input source.
―USB-C#1 and DP cannot be displayed at the same time in PIP/PBP Mode.
―Factory reset does not change these USB port assignments.
―When you assign a USB port, it is not necessary to press the JOG button for confirmation. If you select an
item, it is applied immediately.
DisplayPort Ver.
Select your DisplayPort version.
―Incorrect settings may cause the screen to go blank. If this occurs, check the device specifications.
―If the monitor is in HDMI/DisplayPort/USB Type-C 1/USB Type-C 2 mode and the screen says Check Signal
Cable or power saving mode activates, press the JOG button to display the function-button screen and
then select the icon. You can select 1.1 or 1.2↑.
HDMI Mode
Select the HDMI mode to use.
―The supportable device and resolution may differ depending on its version.
―When the version is changed, the screen may blink.
―If you set the HDMI Mode to 1.4, some high resolutions may not be supported because of bandwidth
limitation of the HDMI 1.4 protocol.
―When the setting is not appropriate, a blank screen may appear. In this case, check the specifications of the
device.
―Set the HDMI Mode to 1.4 when there is no sound output from the DVD connected to our product.
―Not available when PIP/PBP Mode is set to On.
46
Smart ECO Saving
The Smart ECO Saving function reduces power consumption by controlling the electric current used by
the monitor panel.
―This menu is not available when Eye Saver Mode is enabled.
•Off: Deactivate the Smart ECO Saving function.
•On: The power consumption will automatically be reduced by about 10 % over the current setting.
(The reduction of power consumption depends on the customer screen brightness condition.)
Off Timer Plus
Configuring Off Timer
Off Timer: Turn on Off Timer mode.
Turn Off After: The off timer can be set within a range of 0 to 23 hours. The product will automatically
power off after the specified number of hours.
―This option is only available when Off Timer is set to On.
―For products for the market in some regions, the Off Timer is set to automatically activate 4 hours after the
product powers on. This is done in accordance with power supply regulations. If you do not want the timer
to activate, go to → System → Off Timer Plus and set Off Timer to Off.
Configuring Eco Timer
Eco Timer: Turn on Eco Timer mode.
Eco Off After: The Eco Timer can be set between 10 and 180 minutes. The product will automatically
power off after the specified time has elapsed.
―This option is only available when Eco Timer is set to On.
PC/AV Mode
Set PC/AV Mode to AV. The picture size will be enlarged.
This option is useful when you view a movie.
•Set to PC when connected to a PC.
•Set to AV when connected to an AV device.
―This feature is only available on the widescreen models that include 16:9, 16:10 and 21:9.
―If the monitor is in HDMI/DisplayPort/USB Type-C 1/USB Type-C 2 mode and the screen says Check Signal
Cable or power saving mode activates, press the JOG button to display the function-button screen and
then select the icon. You can select PC or AV.
47
Source Detection
Select either Auto or Manual as the method to recognize input signal.
Key Repeat Time
Control the response rate of a button when the button is pressed.
Acceleration, 1 sec, or 2 sec can be selected. If No Repeat is selected, a command responds only once
when a button is pressed.
Power LED On
Configure the settings to enable or disable the power LED located at the lower part of the product.
•Working: The power LED is on when the product is turned on.
•Stand-by: The power LED is on when the product is turned off.
Reset All
Return all the settings for the product to the default factory settings.
Information
View the current input source, frequency, software version, and resolution.
48
Installing the Software
Chapter 08
Easy Setting Box
Easy Setting Box enables users to use the monitor by partitioning multiple sections.
To install the latest version of Easy Setting Box, download it from the Samsung Electronics website at
http://www.samsung.com.
―The software may not work properly if you do not restart the computer after the installation.
―The Easy Setting Box icon may not appear depending on the computer system and the product
specifications.
―If the shortcut icon does not appear, press the F5 key.
Restrictions and Problems with the Installation
The Easy Setting Box installation may be affected by the Graphics Card, Motherboard and the
Networking Environment.
System Requirements
OS Hardware
•Windows 7 32Bit/64Bit
•Windows 8 32Bit/64Bit
•Windows 8.1 32Bit/64Bit
•Windows 10 32Bit/64Bit
•At least 32MB of memory
•At least 60MB of free space on the hard disk drive
49
Troubleshooting Guide
Chapter 09
Requirements Before Contacting Samsung
Customer Service Center
―Before calling Samsung Customer Service Center, test your product as follows. If the problem persists,
contact Samsung Customer Service Center.
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen is turned off and the power indicator blinks even though the product is properly connected
to a PC, perform a self-diagnosis test.
1
Power off both the PC and product.
2
Disconnect the cables from the product.
3
Power on the product.
4
If the message Check Signal Cable appears, the product is working normally.
―If the screen remains blank, check the PC system, video controller and cable.
Checking the Resolution and Frequency
For a mode that exceeds the supported resolution(refer to Standard Signal Mode Table), the message
Not Optimum Mode will appear for a short time.
―The displayed resolution may vary, depending on the computer system settings and cables.
Check the following.
Installation issue (PC mode)
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connectors are locked.
Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected
to the product and PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the
screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the
graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust
the screen settings.)
Screen issue
The power LED is off. The screen will not switch on.
Check that the power cable is connected properly.
The message Check Signal Cable appears.
Check that the cable is properly connected to the product.
Check that the device connected to the product is powered on.
When using the Type-C cable, check whether it supports data communication.
50
Not Optimum Mode is displayed.
This message appears when the signal from the graphics card exceeds the maximum resolution or
frequency for the product.
Change the maximum resolution and frequency to suit the product performance, referring to
Standard Signal Mode Table (P.54).
The images on the screen look distorted.
Check the cable connection to the product.
The screen is not clear. The screen is blurry.
Remove any accessories (video extension cable, etc.) and try again.
Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky. There are shadows or ghost images left on the screen.
Check that the resolution and frequency for the PC are within the range of resolution and frequency
compatible with the product. Next, if required, change the settings, referring to Standard Signal
Mode Table (P.54) in this manual and the Information menu on the product.
The screen is too bright. The screen is too dark.
Adjust Brightness and Contrast.
Screen color is inconsistent.
Change the Color settings.
The colors on the screen have a shadow and are distorted.
Change the Color settings.
White does not really look white.
Change the Color settings.
There is no image on the screen and the power LED blinks every 0.5 to 1 second.
The product is operating in power-saving mode.
Press any key on the keyboard or move the mouse to return to normal operating mode.
Text is blurry.
If using a Windows OS (e.g. Windows 7, Windows 8, Windows 8.1 or Windows 10): Go to Control Panel →
Fonts → Adjust ClearType text and change Turn on ClearType.
Video playback is choppy.
Playback of high-definition large video files can be choppy. This may be because the video player is
not optimized for the computer resource.
Try playing the file on another video player.
Sound issue
There is no sound.
Check the connection of the audio cable or adjust the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound
card or software program.
Video is available but there is no sound.
Sound cannot be heard if a HDMI-DVI cable is used to connect the input device.
Connect the device using an HDMI cable, DP cable or USB Type-C cable.
Source device issue
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
―The LED lights on the frame of the product may be seen depending on the user's viewing angle. The light is
harmless to people and has no bearing on product features and performance. The product is safe to use.
51
Universal Serial Bus (USB) issue
USB interface is not working (USB devices are not working).
Check that your monitor is turned on.
Reconnect the USB cable to your computer.
Reconnect the USB devices (USB connectors).
Turn off and then turn on the monitor again.
Reboot the computer.
Some USB devices like external portable HDDs require a higher electric current. Then connect the
devices directly to the computer.
The USB Type-C port does not supply power (USB devices are not charged).
Check that the connected device is compliant with the USB-C specification.
Check that you use the USB Type-C cable shipped with your monitor.
The High Speed USB 3.0 interface is slow (The High Speed USB 3.0 devices work slowly or do not
work at all).
Check that your computer is USB 3.0-campatible.
Some computers have USB 3.0, USB 2.0, and USB 1.1 ports. Ensure that the correct USB port is being
used.
Reconnect the USB cable to your computer.
Reconnect the USB devices (USB connectors).
Reboot the computer.
USB 3.0 is supported only when a source device is connected to or using a USB
Type-C to A (3.0) cable.
The wireless mouse is lagging or not working (responds slowly or does not respond).
Increase the distance between the USB device and the wireless USB receiver.
Position the wireless USB receiver as close as possible to the wireless mouse.
Use a USB-extender cable to position the wireless USB receiver as far away as possible from the USB
port.
52
Q & A
―Refer to the user manual for your PC or graphics card for further instructions on adjustment.
How can I change the frequency?
Set the frequency on your graphics card.
•Windows 7: Go to Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor, and adjust Refresh rate under Monitor settings.
•Windows 8(Windows 8.1): Go to Settings → Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor, and adjust Refresh rate under Monitor settings.
•Windows 10: Go to Settings → System → Display → Advanced display settings → Display adapter properties → Monitor, and adjust Screen refresh rate under Monitor settings.
How can I change the resolution?
•Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust Resolution, and adjust the resolution.
•Windows 8(Windows 8.1): Go to Settings → Control Panel → Appearance and Personalization → Display → Adjust Resolution, and adjust the resolution.
•Windows 10: Go to Settings → System → Display → Advanced display settings, and adjust the resolution.
How do I set power-saving mode?
•Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings → Power options or BIOS SETUP on the PC.
•Windows 8(Windows 8.1): Set power-saving mode in Settings → Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings → Power options or BIOS SETUP on the PC.
•Windows 10: Set power-saving mode in Settings → Personalization → Lock screen → Screen timeout settings → Power & sleep or BIOS SETUP on the PC.
53
Specifications
Chapter 10
General
Model Name C43J890DK* / C43J892DK* C49J890DK* / C49J892DK*
Size
43 Class (43.4 Inches / 110.2 cm) 49 Class (48.9 Inches / 124.2 cm)
Display area
1052.3 mm (H) x 328.8 mm (V)
41.4 Inches (H) x 12.9 Inches (V)
1195.8 mm (H) x 336.3 mm (V)
47.1 Inches (H) x 13.2 Inches (V)
Pixel Pitch
0.274 mm (H) x 0.274 mm (V)
0.010787 Inches (H) x 0.010787 Inches (V)
0.3114 mm (H) x 0.3114 mm (V)
0.01226 Inches (H) x 0.01226 Inches (V)
Maximum Pixel
Clock
600 MHz 660 MHz
Power Supply
AC100-240V~ 50/60Hz
Refer to the label at the back of the product as the standard voltage can vary in
different countries.
Signal
connectors
HDMI, DP, USB Type-C
Environmental
conditions
Operating
Temperature: 50 °F – 104 °F (10 °C – 40 °C)
Humidity: 10 % – 80 %, non-condensing
Storage
Temperature: -4 °F – 113 °F (-20 °C – 45 °C)
Humidity: 5 % – 95 %, non-condensing
―Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data
exchange between the monitor and PC system optimizes the monitor settings. Monitor installation takes
place automatically. However, you can customize the installation settings if desired.
―Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be
brighter or darker on the LCD panel. This does not affect product performance.
―The above specifications are subject to change without notice to improve quality.
―This device is a Class B digital apparatus.
―For detailed device specifications, visit the Samsung Electronics website.
54
Standard Signal Mode Table
Model Name C43J890DK* / C43J892DK* C49J890DK* / C49J892DK*
Synchronization Horizontal Frequency
30 – 160 kHz 30 – 170 kHz
Vertical Frequency
50 – 120 Hz 50 – 144 Hz
Resolution Optimum Resolution
3840 x 1200 @ 60 Hz 3840 x 1080 @ 60 Hz
Maximum Resolution
3840 x 1200 @ 100 Hz (HDMI)
3840 x 1200 @ 120 Hz (DisplayPort)
3840 x 1200 @ 120 Hz (USB Type-C)
3840 x 1080 @ 120 Hz (HDMI)
3840 x 1080 @ 144 Hz (DisplayPort)
3840 x 1080 @ 144 Hz (USB Type-C)
If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted. If the signal transmitted from the PC does not belong to the standard signal
modes, the screen may be blank even though the power LED turns on. In such a case, change the settings according to the following table by referring to the graphics card user manual.
C43J890DK* / C43J892DK*
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)
CEA, 2560 x 1080
66.000 60.000 198.000 +/+
IBM, 720 x 400
31.469 70.087 28.322 -/+
MAC, 640 x 480
35.000 66.667 30.240 -/-
MAC, 832 x 624
49.726 74.551 57.284 -/-
MAC, 1152 x 870
68.681 75.062 100.000 -/-
VESA, 640 x 480
31.469 59.940 25.175 -/-
VESA, 640 x 480
37.861 72.809 31.500 -/-
VESA, 640 x 480
37.500 75.000 31.500 -/-
VESA, 800 x 600
35.156 56.250 36.000 +/+
VESA, 800 x 600
37.879 60.317 40.000 +/+
VESA, 800 x 600
48.077 72.188 50.000 +/+
VESA, 800 x 600
46.875 75.000 49.500 +/+
VESA, 1024 x 768
48.363 60.004 65.000 -/-
VESA, 1024 x 768
56.476 70.069 75.000 -/-
VESA, 1024 x 768
60.023 75.029 78.750 +/+
55
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)
VESA, 1152 x 864
67.500 75.000 108.000 +/+
VESA, 1280 x 720
45.000 60.000 74.250 +/+
VESA, 1280 x 800
49.702 59.810 83.500 -/+
VESA, 1280 x 1024
63.981 60.020 108.000 +/+
VESA, 1280 x 1024
79.976 75.025 135.000 +/+
VESA, 1440 x 900
55.935 59.887 106.500 -/+
VESA, 1600 x 900
60.000 60.000 108.000 +/+
VESA, 1680 x 1050
65.290 59.954 146.250 -/+
VESA, 1920 x 1080
67.500 60.000 148.500 +/+
VESA, 3840 x 1200
74.063 59.970 296.250 +/-
VESA, 3840 x 1200
125.750 99.960 503.000 +/-
VESA, 3840 x 1200
152.520 120.000 597.880 +/-
C49J890DK* / C49J892DK*
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)
CEA, 2560 x 1080
66.000 60.000 198.000 +/+
IBM, 720 x 400
31.469 70.087 28.322 -/+
MAC, 640 x 480
35.000 66.667 30.240 -/-
MAC, 832 x 624
49.726 74.551 57.284 -/-
MAC, 1152 x 870
68.681 75.062 100.000 -/-
VESA, 640 x 480
31.469 59.940 25.175 -/-
VESA, 640 x 480
37.861 72.809 31.500 -/-
VESA, 640 x 480
37.500 75.000 31.500 -/-
VESA, 800 x 600
35.156 56.250 36.000 +/+
VESA, 800 x 600
37.879 60.317 40.000 +/+
VESA, 800 x 600
48.077 72.188 50.000 +/+
VESA, 800 x 600
46.875 75.000 49.500 +/+
VESA, 1024 x 768
48.363 60.004 65.000 -/-
VESA, 1024 x 768
56.476 70.069 75.000 -/-
VESA, 1024 x 768
60.023 75.029 78.750 +/+
VESA, 1152 x 864
67.500 75.000 108.000 +/+
56
VESA, 1280 x 720
45.000 60.000 74.250 +/+
VESA, 1280 x 800
49.702 59.810 83.500 -/+
VESA, 1280 x 1024
63.981 60.020 108.000 +/+
VESA, 1280 x 1024
79.976 75.025 135.000 +/+
VESA, 1440 x 900
55.935 59.887 106.500 -/+
VESA, 1600 x 900
60.000 60.000 108.000 +/+
VESA, 1680 x 1050
65.290 59.954 146.250 -/+
VESA, 1920 x 1080
67.500 60.000 148.500 +/+
VESA, 3840 x 1080
66.625 59.968 266.500 +/-
VESA, 3840 x 1080
113.250 99.956 453.000 +/-
VESA, 3840 x 1080
137.250 119.974 549.000 +/-
VESA, 3840 x 1080
166.608 144.000 653.103 +/-
―Horizontal Frequency
The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in
kHz.
―Vertical Frequency
Repeating the same picture dozens of times per second allows you to view natural pictures. The repeat frequency is called "vertical frequency" or "refresh rate" and is indicated in Hz.
―This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality.
To avoid this, it is recommended that you select the optimum resolution specified for your product.
―Some resolutions listed in the table above may not be available depending on graphics card specifications.
57
Appendix
Chapter 11
Responsibility for the Pay Service (Cost to
Customers)
―When the service is requested, in spite of in warranty, we may charge you for a visit from a service
technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•If a service technician gives instructions on how to use product or simply adjusts options without
disassembling product.
•If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
•If a product is reinstalled or devices are connected additionally after installing the purchased
product for the first time.
•If a product is reinstalled to move to a different spot or to move to a different house.
•If customer requests instructions on how to use because of another company's product.
•If customer requests instructions on how to use the network or another company's Program.
•If customer requests software installation and setup for the product.
•If a service technician removes/cleans dusts or foreign materials inside of the product.
•If customer requests an installation additionally after purchasing a product through home-
shopping or online.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•External impact or drop.
•Use of supplies or separately sold product unspecified by Samsung.
•Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
•Remodeling or repairing the product by customer.
•Using it with incorrect voltage or non-authorized electrical connections.
•Not following the "cautions" in User Manual.
Others
•If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator,
Lamp, Filter, Ribbon, etc.)
―If customer requests a service in case the product has no defect, service fee may be charged. So please
read User Manual first.
58
Extended warranty
You can buy an extended warranty within 90 days of purchasing the product.
The extended warranty will cover an additional period of 3 years, beyond the standard 3 year warranty.
Samsung guarantee that replacement parts will be available for 5 years after the end of production.
After 5 years, in the event that the Samsung’s service center has run out of replacement parts and
cannot repair the product, Samsung will replace your product at no additional charge. If the model you
purchased is no longer available, Samsung replace it with the current equivalent model.