Samsung DW60A8070BB User Manual
Displayed below is the user manual for DW60A8070BB by Samsung which is a product in the Dishwashers category. This manual has pages.
Related Manuals
DISHWASHER
REPAIR Guide
DISHWASHER
Basic Model : DW60R7070 Series
DW60R7050 Series
DW60R7040 Series
Model Name : DW60A8070 Series
DW60A8060 Series
DW60A8050 Series
DW60A8040 Series
Model Code : DW60A8070BB, DW60A8070US,
DW60A8060BB, DW60A8060IB,
DW60A8060FS, DW60A8060FW,
DW60A8050BB, DW60A8050US,
DW60A8050FS, DW60A8040BB
DW60A8040IB
* For End User.
IMPORTANT SAFETY NOTICE
Following the repair by a non-authorized service provider self-repair or
non-professional repair of the product Samsung is not liable for any
damage to the product any injury or any other product safety issue caused
by any attempt to repair the product which does not carefully follow these
repair and maintenance instructions. Any damage to the product caused by
an attempt to repair the product by any person other than a Samsung
certified service provider will not be covered by the warranty.
All rights reserved.
This service guide may not be reproduced in whole or
as a part in any form whatsoever without the written permission of
the SAMSUNG ELECTRONICS Company.
WARNING
Note
1. You can check where to buy replacement parts at http://samsung.com
2. Visit the part purchase site and enter the model code of your product to check the parts available
for purchase. The model code is labelled on the edge of the tub. When you open the dishwasher’s
door, you can check the model code and version on the barcode label at the left side of the tub.
3. For replacement parts make sure the part name matches that of the illustration in this manual.
- User-serviceable parts are limited to door hinge and seals other seals spray arms drain lters
interior racks and plastic peripherals such as baskets and lids.
Caution
1. The part name listed on the site may differ from that in this manual. Please make sure you choose
the right part name.
2. Be sure to wear safety gloves while making repairs.
3. Must working more than 2 people to handling heavy weight.
Disassembly and Reassembly _ 3
1. TOOLS FOR REMOVAL AND REASSEMBLY
Tool image
No. Tool Type Remarks
①Adjustable Wrench
②Open-end Wrench 1-7/16”
③Vice Pliers
④Others
(screwdriver, nipper, long nose pliers)
Common tools for servicing
Screwdriver – Phillip, Flat, Torx T15
⑤Ear clamping tool In reassembling of the clamp-bend(ear clamp) using our
SVC part, this tool is needed.
NOTE :
Preparation for parts replacement
1. Remove the residual water inside the product. (Drain the water by operating the drain pump)
2. Close the water supply valve.
3. Turn off the power & disconnect the power cable.
You must turn off the circuit breaker connected to the product.
4. Pull out the unit from the sink and lay it on the oor.
Be careful of the drain hose when pulling out the unit.
4 _ Disassembly and Reassembly
2. STANDARD DISASSEMBLY DRAWINGS
2-1. PRECAUTION
Caution
Before servicing,
- Make sure to remove all items include baskets inside dishwasher.
- Drain the water in the dishwasher and disconnect the power supply.
- Lock the water faucet that is connected with inlet hose.
- Uninstall the dishwasher from the furniture cabinet except simple work.
- Disconnect the Inlet & Drain hoses from the duct, if the hoses are too short to pull the dishwasher out of the furniture
cabinet enough.
- Make sure to remove any remaining water in the Sump and hoses by rag or vacuum.
→ There is a risk of water spill on the oor.
Disassembly and Reassembly _ 5
2-2. FRESH TANK / CAP CASE BRAKE / GASKET BRAKE (DW60A8070*/
DW60A8060* MODELS)
- FRESH TANK : DD82-01910A / SVC ASSY-FRESH TANK
- CAP CASE BRAKE : DD81-02725A / SVC CAP CASE BRAKE
- GASKET BRAKE : DD81-02726A / SVC GASKET BRAKE
Part Figure Description
CAP CASE
BRAKE/
GASKET
BRAKE/
(DW60A8070*/
DW60A8060*
models)
A
B
[DISASSEMBLY]
1. Remove 3 screws that connect left SIDE PANEL to
front side of dishwasher.
- Type A: DD81-02693A / 2 pcs
- Type B: DD81-02694A / 1 pc
- HOUSING-LEFT : DD81-02928B/DD81-02880A/
DD81-02880C
FRESH TANK replacement: Empty the FRESH TANK
before repair. (Refer to ~page for how to empty)
WARNING
Be sure to remove the power plug before
servicing.
CAUTION
Empty the water container before lay down set.
(Refer to ~page for how to empty)
In case of Free Standing models, there’re no
screws of type B.
C
B
2
1
2. Remove 3 screws at the back side of dishwasher.
- Type C: DD81-02692A / 1 pc
- Type B: DD81-02694A / 2 pcs
In case of Free Standing models, take off the
COVER TOP by removing 2 screws of type A.
After removing screws, pull the COVER TOP
backward rst, and take it off upward.
-TOP COVER : DD81-02552C/DD81-02552D
Guide Tub Top
3. Remove 1 screw at the left side of GUIDE TUB TOP.
- Screw: DD81-02694A / 1 pc
- GUIDE TUB TOP : DD81-02733A
6 _ Disassembly and Reassembly
Part Figure Description
CAP CASE
BRAKE/
GASKET
BRAKE/
(DW60A8070*/
DW60A8060*
models)
4. Take off the left SIDE PANEL.
WARNING
Do not this work without safety gloves.
It may cause injury from sharp edges.
5. Take off the CAP CASE BRAKE by rotating in a
counter-clockwise direction with long-nose pliers.
- CAP CASE BRAKE : DD81-02725A
CAUTION
It can be brake easily when you use the iron part
of the pliers. Take off the cap using the handle part
of the pliersto prevent damage.
Fresh Tank
6. Remove 1 screw from the FRESH TANK assembly.
- Screw : DD81-02694A / 1pc
Gasket brake
7. Remove the GASKET BRAKE from the FRESH
TANK assembly.
- GASKET-BRAKE : DD81-02726A
Cap Case brake Gasket brake
Disassembly and Reassembly _ 7
Part Figure Description
CAP CASE
BRAKE/
GASKET
BRAKE/
(DW60A8070*/
DW60A8060*
models)
[ASSEMBLY]
1. Fit the GASKET BRAKE on the FRESH TANK, and
attach the FRESH TANK with screws.
- Screw : DD81-02694A / 1pc
CAUTION
Pay attention to assemble the seal correctly.
It can cause the water leakage when it’s
assembled wrong.
2. fasten the CAP CASE BRAKE by rotating in a
clockwise direction with long-nose pliers.
CAUTION
It can be break easily when you the use iron part
of the pliers. Take off the cap using the handle part
of the pliers to prevent damage.
3. Assemble the left SIDE PANEL with the screws.
CAUTION
Fasten the screws that was assembled to origin
location.
Don’t assemble to other locations.
WARNING
Do not this work without safety gloves.
It can cause injury from sharp edge.
8 _ Disassembly and Reassembly
2-3. RECYCLE TANK / DUCT DRY NUT / GASKET BRAKE (DW60A8070*/
DW60A8060* MODELS)
- RECYCLE TANK : DD82-01909A / SVC ASSY-RECYCLE TANK
- DUCT DRY NUT : DD81-02705A / SVC-DUCT DRY NUT
Part Figure Description
RECYCLE
TANK/
DUCT DRY NUT/
GASKET
BRAKE
(DW60A8070*/
DW60A8060*
models)
A
B
[DISASSEMBLY]
1. Remove 3 screws that connect right SIDE PANEL
to front side of dishwasher.
- Type A: DD81-02693A / 2 pcs
- Type B: DD81-02694A / 1 pc
- HOUSING_RIGHT : DD81-02929B/DD81-
02881A/DD81-02881C
WARNING
Be sure to remove the power plug before
servicing.
In case of Free Standing models, there’re no
screws of type B.
CAUTION
RECYCLE TANK replacement: Empty the
RECYCLE TANK before repair. (Refer to ~page
for how to empty)
C
B
2
1
2. Remove 3 screws at the back side of dishwasher.
- Type C: DD81-02692A / 1 pc
- Type B: DD81-02694A / 2 pcs
In case of Free Standing models, take off the
COVER TOP by removing 2 screws of type A.
After removing screws, pull the COVER TOP
backward rst, and take it off upward.
- TOP COVER : DD81-02552C/DD81-02552D
Guide Tub Top
3. Remove 1 screw at the left side of GUIDE TUB TOP.
- Screw: DD81-02694A / 1 pc
- GUIDE TUB TOP : DD81-02733A
Disassembly and Reassembly _ 9
Part Figure Description
RECYCLE
TANK/
DUCT DRY NUT/
GASKET
BRAKE
(DW60A8070*/
DW60A8060*
models)
4. Remove the right SIDE PANEL.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
5. Remove the DUCT DRY NUT by rotating in a
counter-clockwise direction with long-nose pliers.
- DUCT DRY NUT : DD81-02705A
CAUTION
It can be brake easily when you use the iron part
of the pliers. Take off the cap using the handle part
of the pliers to prevent damage.
Recycle Tank
6. Remove 1 screw from the RECYCLE TANK
assembly.
- Screw : DD81-02694A / 1pc
Gasket brake
7. Remove the GASKET BRAKE from the RECYCLE
TANK assembly.
- GASKET-BRAKE : DD81-02726A
Duct Dry Nut Gasket brake
10 _ Disassembly and Reassembly
Part Figure Description
RECYCLE
TANK/
DUCT DRY NUT/
GASKET
BRAKE
(DW60A8070*/
DW60A8060*
models)
Gasket brake
[ASSEMBLY]
1. Fit the GASKET BRAKE on the RECYCLE TANK,
and attach the FRESH TANK with screws.
- Screw : DD81-02694A / 1pc
CAUTION
Pay attention to assemble the seal correctly. It
can cause the water leakage when it’s assembled
wrong.
2. fasten the DUCT DRY NUT by rotating in a
clockwise direction
CAUTION
Wear gloves with friction and tighten rmly.
Otherwise, there is a risk of leakage.
3. Assemble the right SIDE PANEL with the screws.
CAUTION
Fasten the screws that was assembled to origin
location.
Don’t assemble to other locations.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
Disassembly and Reassembly _ 11
2-4. CASE BRAKE / CAP CASE BRAKE / GASKET BRAKE (DW60A8050*/
DW60A8040* MODELS)
- CASE BRAKE : DD82-01446A / SVC ASSY-CASE BRAKE
- CAP CASE BRAKE : DD81-02725A / SVC CAP CASE BRAKE
- GASKET BRAKE : DD81-02726A / SVC GASKET BRAKE
Part Figure Description
CASE BRAKE/
CAP CASE
BRAKE/
GASKET
BRAKE
(DW60A8050*/
DW60A8040*
models)
A
B
[DISASSEMBLY]
1. Remove 3 screws that connect left SIDE PANEL to
front side of dishwasher.
- Type A: DD81-02693A / 2 pcs
- Type B: DD81-02694A / 1 pc
- HOUSING-LEFT : DD81-02928B/DD81-02880A/
DD81-02880C
WARNING
Be sure to remove the power plug before
servicing.
In case of Free Standing models, there’re no
screws of type B.
C
B
2
1
2. Remove 3 screws at the back side of dishwasher.
- Type C: DD81-02692A / 1 pc
- Type B: DD81-02694A / 2 pcs
In case of Free Standing models, take off the
COVER TOP by removing 2 screws of type A.
After removing screws, pull the COVER TOP
backward rst, and take it off upward.
- TOP COVER : DD81-02552C/DD81-02552D
Guide Tub Top
3. Remove 1 screw at the left side of GUIDE TUB TOP.
- Screw: DD81-02694A / 1 pc
- GUIDE TUB TOP : DD81-02733A
12 _ Disassembly and Reassembly
Part Figure Description
CASE BRAKE/
CAP CASE
BRAKE/
GASKET
BRAKE
(DW60A8050*/
DW60A8040*
models)
4. Take off the left SIDE PANEL.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
5. Take off the CAP CASE BRAKE by rotating to
counter-clockwise direction with long-nose pliers.
- CAP CASE BRAKE : DD81-02725A
CAUTION
It can be broken easily when you use the iron part
of the pliers. Take off the cap using the handle part
of the pliers to prevent damage.
Gasket brake
Cap Case brake Gasket brake
6. Remove the GASKET BRAKE from the CASE
BRAKE assembly.
- GASKET-BRAKE : DD81-02726A
[ASSEMBLY]
1. Fit the GASKET BRAKE on the CASE BRAKE,
and fasten the CAP CASE BRAKE by rotating in a
clockwise direction with long-nose pliers.
CAUTION
It can be break easily when you use the iron part
of the pliers. Take off the cap using the handle part
of the pliers to prevent damage.
CAUTION
Pay attention to assemble the seal correctly.
It can cause the water leakage when it’s
assembled wrong.
2. Assemble the left SIDE PANEL with the screws.
CAUTION
Fasten the screws that was assembled to origin
location. Don’t assemble to other locations.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
Disassembly and Reassembly _ 13
2-5. CONTROL PANEL
- CONTROL PANEL : DD82-01903B, DD82-01903D / SVC ASSY-CONTROL PANEL
Part Figure Description
CONTROL
PANEL
(DW60A80**U*/
DW60A80**F*)
[DISASSEMBLY]
1. Open the dishwasher’s DOOR.
WARNING
Be sure to remove the power plug before
servicing.
CAUTION
Make sure to Remove the power plug before
servicing.
B
A
BA
2. Remove 10 screws that connect the ASSY
CONTROL PANEL to the dishwasher’s DOOR with
Torx® T15 screwdriver.
- Type A: DD81-03011A / 6 pcs
- Type B: DD81-02758A / 4 pcs
SUB TOUCH PBA
DW60A8070*/ DW60A8060*/
DW60A8050* models
DW60A8040* models
LAN PBA (WIFI)
3. Remove the wire harness that connect MAIN PBA
to SUB TOUCH PBA.
4. In the case of DW60A8070*/DW60A8060*/
DW60A8050* models, also remove the LAN PBA
(Wi-Fi) connector.
- ASSY-CONTROL PANEL : DD82-01903B/DD82-
01903D
14 _ Disassembly and Reassembly
Part Figure Description
CONTROL
PANEL
(DW60A80**U*/
DW60A80**F*)
SUB TOUCH PBA
DW60A8070*/ DW60A8060*/
DW60A8050* models
DW60A8040* models
LAN PBA (WIFI)
[ASSEMBLY]
1. Connect wire terminal to connect MAIN PBA to
SUB TOUCH PBA.
2. In the case of DW60A8070*/DW60A8060*/
DW60A8050* models, connect the LAN PBA (Wi-Fi)
connector as well.
CAUTION
Make sure the Wire harness are not getting stuck
in other parts.
B
A
3. Fix 10 screws to connect the ASSY CONTROL
PANEL to the dishwasher’s DOOR with Torx® T15
screwdriver.
- Type A: DD81-03011A / 6 pcs
- Type B: DD81-02758A / 4 pcs
Disassembly and Reassembly _ 15
- CONTROL PANEL : DD82-01903A, DD82-01903C, DD82-01903E, DD82-01903F / SVC ASSY-CONTROL PANEL
Part Figure Description
CONTROL
PANEL/
(DW60A80*0BB/
DW60A80*0IB)
[DISASSEMBLY]
1. Open the dishwasher’s DOOR.
It doesn’t need to uninstall the dishwasher from the
furniture cabinet.
WARNING
Be sure to remove the power plug before
servicing.
BA
B
A
2. Remove 8 screws that connect the ASSY
CONTROL PANEL to the dishwasher’s DOOR with
Torx® T15 screwdriver.
- Type A: DD81-03011A / 6 pcs
- Type B: DD81-02758A / 2 pcs
SUB PBA
DW60A8070*/ DW60A8060*/
DW60A8050* models
DW60A8040* models
LAN PBA (WIFI)
3. Remove wire connector that connect MAIN PBA to
SUB PBA.
4. In the case of DW60A8070*B/DW60A8060*B/
DW60A8050*B models, also remove the LAN PBA
(Wi-Fi) connector.
- ASSY-CONTROL PANEL : DD82-01903A/DD82-
01903C/DD82-01903E
16 _ Disassembly and Reassembly
Part Figure Description
CONTROL
PANEL/
(DW60A80*0BB/
DW60A80*0IB)
SUB PBA
DW60A8070*/ DW60A8060*/
DW60A8050* models
DW60A8040* models
LAN PBA (WIFI)
[ASSEMBLY]
1. Connect the Wire harness that connect MAIN PBA
to SUB PBA.
In case of DW60A8070*B/DW60A8060*B/
DW60A8050*B models, connect the wire
connector of LAN PBA (WIFI) as well.
CAUTION
Make sure the Wire harness are not getting stuck
in other parts.
BA
2. Fix 8 screws to connect the ASSY CONTROL
PANEL to the dishwasher’s DOOR with Torx® T15
screwdriver.
- Type A: DD81-02756A / 2 pcs
- Type B: DD81-02758A / 6 pcs
Disassembly and Reassembly _ 17
2-6. DOOR OUTER
- DOOR OUTER : DD81-02455B (*BB models), DD81-02455D (*IB models), DD81-02521A (*FS models),
DD81-02521B (*FW models) / SVC DOOR OUTER
Part Figure Description
DOOR OUTER
A
B
DW60A80**F*/
DW60A80**U* models
A
B
DW60A80**BB/
DW60A80**IB models
[DISASSEMBLY]
1. Open the dishwasher’s DOOR, and remove 8
screws to take off DOOR OUTER.
Screws on DOOR are Torx® T15 type. Use the
Torx® T15 screw driver when release the screws.
• DW60A80**F*/DW60A80**U* models
- Type A: DD81-02758A / 4 pcs
- Type B: DD81-02757A / 4 pcs
• DW60A80**BB/DW60A80**IB models
- Type A: DD81-02758A / 2 pcs
- Type B: DD81-02757A / 6 pcs
AB
WARNING
Be sure to remove the power plug before
servicing.
CAUTION
Be careful to avoid injury when the DOOR is
closed after removing DOOR OUTER.
CAUTION
The screws can fall into the SUMP after disassembly.
Keep the screws in a safe place to reassemble the
DOOR.
1
2
DW60A80**F*/
DW60A80**U* models
DW60A80**BB/
DW60A80**IB models
2. Remove the DOOR OUTER.
WARNING
Do not this work without safety gloves.
It can cause injury from sharp edge.
- DOOR OUTER : DD81-02521A/DD81-02521B/
DD81-02455B
18 _ Disassembly and Reassembly
Part Figure Description
DOOR OUTER
1
2
DW60A80**F*/
DW60A80**U* models
DW60A80**BB/
DW60A80**IB models
[ASSEMBLY]
1. Assemble the holes of DOOR OUTER to hooks of
CONTROL PANEL
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
Holes of DOOR OUTER Hooks of CONTROL PANEL
A
B
DW60A80**F*/
DW60A80**U* models
A
B
DW60A80**BB/
DW60A80**IB models
2. Fasten 8 screws to x the DOOR OUTER.
Screws on DOOR are Torx® T15 type. Use the
Torx® T15 screw driver when release the screws.
• DW60A80**F*/DW60A80**U* models
- Type A: DD81-02758A / 4 pcs
- Type B: DD81-02757A / 4 pcs
• DW60A80**BB/DW60A80**IB models
- Type A: DD81-02758A / 2 pcs
- Type B: DD81-02757A / 6 pcs
AB
Disassembly and Reassembly _ 19
2-7. HOLDER HINGE
- HOLDER HINGE : DD81-02763A / SVC HOLDER HINGE
Part Figure Description
HOLDER HINGE
(DW60A80**BB/
DW60A80**F*/
DW60A80**U*
models)
[DISASSEMBLY]
*
PREPARATION: Disassemble SIDE PANEL left & right.
1. Remove HOLDER ROPE DOOR from the DOOR
HINGE left & right with the DOOR closed.
WARNING
Be sure to remove the power plug before
servicing.
CAUTION
Pay attention to DOOR drop after remove the
rope.
It can cause injury.
- ASSY-HINGE-RIGHT : DD82-01675A
- ASSY-HINGE-LEFT : DD82-01676A
2. Remove HOLDER HINGE from the DOOR HINGE.
CAUTION
Be careful to avoid injury from the DOOR drop
without HOLDER ROPE DOOR.
Rotate the HOLDER HINGE to release from hook.
-HOLDER HINGE : DD81-02763A
[ASSEMBLY]
* Reassembly is the reverse order of disassembly.
20 _ Disassembly and Reassembly
2-8. DOOR HINGE / GUIDE HINGE
- DOOR HINGE LEFT : DD82-01676A / SVC ASSY-HINGE LEFT
- DOOR HINGE RIGHT : DD82-01675A / SVC ASSY-HINGE RIGHT
Part Figure Description
DOOR HINGE/
GUIDE HINGE
(DW60A80**BB/
DW60A80**F*/
DW60A80**U*
models)
Hook Hook
[DISASSEMBLY]
* PREPARATION: Disassemble DOOR OUTER,
CONTROL PANEL and SIDE PANEL left & right.
1. Remove 2 terminals that connected to
DETERGENT DISPENSER, and 1 ground wire that
connected to BRACKET DOOR FRAME.
WARNING
Be sure to remove the power plug before
servicing.
CAUTION
Pay attention to hook of terminals.
2. Remove HOLDER ROPE DOOR from the DOOR
HINGE left & right with the DOOR closed.
CAUTION
Pay attention to DOOR drop after remove the
rope. It can cause injury.
GUIDE HINGE
3. Push both ribs of GUIDE HINGE to pull out the DOOR.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge of broken parts.
Disassembly and Reassembly _ 21
Part Figure Description
DOOR HINGE/
GUIDE HINGE
(DW60A80**BB/
DW60A80**F*/
DW60A80**U*
models)
About 15˚
4. Do same work at the opposite side, and pull out the
DOOR INNER assembly to the direction of about 15˚.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
5. Remove 2 screws to take off BRACKET DOOR
FRAME from the DOOR INNER.
- Screws: DD81-02728A / 2 pcs
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
6. Remove 2 screw at each side to take off DOOR
HINGE from the DOOR INNER.
- Screws: DD81-02764A / 4 pcs
7. Take off the GUIDE HINGE from the DOOR
HINGE.
22 _ Disassembly and Reassembly
Part Figure Description
DOOR HINGE/
GUIDE HINGE
(DW60A80**BB/
DW60A80**F*/
DW60A80**U*
models)
[ASSEMBLY]
1. Assemble the DOOR HINGE assembly and
BRACKET DOOR FRAME with machine screws.
- Screws for DOOR HINGE assembly:
DD81-02764A / 4 pcs
- Screws for BRACKET DOOR FRAME:
DD81-02728A / 2 pcs
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
About 15˚
2. Fit the DOOR INNER assembly into the holder of
TUB to lock the hook of DOOR HINGE.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
3. Fit the HOLDER ROPE DOOR on the both side of
DOOR HINGE with the DOOR closed.
4. Connect 2 terminals of DETERGENT DISPENSER,
and 1 ground wire.
CAUTION
Make sure the Wire harness are not getting stuck
in other parts.
Disassembly and Reassembly _ 23
Part Figure Description
ASSY-HINGE
RIGHT/ ASSY-
HINGE LEFT
(DW60A80**IB
models)
BA[DISASSEMBLY]
1. Remove 8 screws that connect the ASSY
CONTROL PANEL to the dishwasher’s DOOR
with Torx® T15 screwdriver. Separate the ASSY
CONTROL PANEL.
- Type A: DD81-02756A / 2 pcs
- Type B: DD81-02758A / 6 pcs
C
2. Open the dishwasher’s DOOR, and remove 6
screws to take off DOOR OUTER.
Type C: DD81-02757A / 6 pcs
WARNING
Be sure to remove the power plug before
servicing.
CAUTION
Be careful to avoid injury when the DOOR is
closed after remove DOOR OUTER.
CAUTION
The screws can fall into the SUMP after
disassembly. Keep the screws to other place to
reassemble the DOOR.
3. Remove the all xing screws of the SIDE PANEL
and separate the SIDE PANEL on both sides.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
4. Open the ASSY DOOR about 45 degrees.
WARNING
Be sure to remove the power plug before
servicing.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
- DOOR HINGE LEFT : DD82-01907A / SVC ASSY-HINGE LEFT
- DOOR HINGE RIGHT : DD82-01908A / SVC ASSY-HINGE RIGHT
24 _ Disassembly and Reassembly
Part Figure Description
ASSY-HINGE
RIGHT/ ASSY-
HINGE LEFT
(DW60A80**IB
models)
5. Open the door to apply tension to the DOOR
SPRING and x the DOOR SPRING with a PIN.
6. Remove the 2 screws which is xed to INNER
DOOR.
7. Remove the stopper by pulling it by hand.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
Disassembly and Reassembly _ 25
Part Figure Description
ASSY-HINGE
RIGHT/ ASSY-
HINGE LEFT
(DW60A80**IB
models)
ASSY HINGE RIGHT
8. Remove the ASSY HINGE RIGHT hanging from
DOOR SPRING.
- ASSY-HINGE-RIGHT : DD82-01908A
- ASSY-HINGE-LEFT : DD82-01907A
[ASSEMBLY]
1. Pull the ASSY HINGE RIGHT to apply tension to
the SPRING and then x the SPRING with a PIN.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
2. Assemble by hanging the hook of ASSY HINGE
RIGHT on DOOR SPRING.
26 _ Disassembly and Reassembly
Part Figure Description
ASSY-HINGE
RIGHT/ ASSY-
HINGE LEFT
(DW60A80**IB
models)
3. Assemble the stopper by pushing it by hand.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
4. Fasten the 2 screws on the side of the INNER
DOOR.
5. After assembling the SIDE PANEL on both sides,
fasten the screws.
A total of 7 screws are fastened to one SIDE
PANEL.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
Disassembly and Reassembly _ 27
Part Figure Description
ASSY-HINGE
RIGHT/ ASSY-
HINGE LEFT
(DW60A80**IB
models)
C
BA
6. Fasten 10 screws to x the DOOR OUTER and
ASSY CONTROL PANEL.
- Type A: DD81-02756A / 2 pcs
- Type B: DD81-02758A / 6 pcs
- Type C: DD81-02757A / 6 pcs
28 _ Disassembly and Reassembly
2-9. SEAL TUB PACKING
- SEAL TUB PACKING : DD81-02770A / SVC SEAL TUB PACKING
Part Figure Description
SEAL TUB
PACKING
Seal tub packing
Bracket seal tub
[DISASSEMBLY]
1. Remove the old seal from the BRACKET SEAL TUB.
WARNING
Be sure to remove the power plug before
servicing.
WARNING
Be careful to touch the BRACKET SEAL TUB after
removed the seal. It can cause injury from sharp
edge.
- SEAL TUB PACKING : DD81-02770A
Insert to Bracket
seal Tub
Seal tip
Seal tip faces
to inside
[ASSEMBLY]
1. Put some water on new SEAL TUB PACKING to
assemble it easily. Fold the SEAL TUB PACKING in
half with the tip of the seal facing inward.
CAUTION
Pay attention to the direction of seal. If it is
assembled in reverse, it may cause leakage of
steam or water.
Center
About 20 cm
2.
Assemble the SEAL TUB PACKING to center of the
BRACKET SEAL TUB. Press seal about 20cm
(red dotted line) on both sides based on the center line.
Disassembly and Reassembly _ 29
Part Figure Description
SEAL TUB
PACKING
About 3~4 cm
3. Put Seal in the left & right side of the bottom.
The folded seal is about 3~4 cm long.
4. Press the seal from the top corner toward remaining
side.
CAUTION
Pay attention to assemble not to deform the seal
tip at the corner. If the gap is opened, it may cause
steam leakage.
30 _ Disassembly and Reassembly
2-10. ROTOR LOWER / ASSY DUCT NOZZLE
- ROTOR LOWER : DD81-02977A / SVC ROTOR LOWER
- ASSY DUCT NOZZLE : DD82-01501A / SVC ASSY-DUCT NOZZLE
Part Figure Description
ROTOR LOWER
/ ASSY DUCT
NOZZLE
[DISASSEMBLY]
1. Open the dishwasher’s DOOR.
Rotor lower
2. Take ROTOR LOWER off upward.
- ROTOR LOWER : DD81-02977A
3. Turn the COARSE FILTER counter-clockwise to
unlock the lter assembly.
- FILTER COARSE : DD81-02452A
4. Remove 2 screws to take off ASSY DUCT NOZZLE.
- Screws: DD81-02718A / 2 pcs
- ASSY DUCT NOZZLE : DD82-01501A
5. Release the hooks from tub holders.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Make sure to reassemble to right location.
There’re risks of leakage or poor performance
when it’s misassembled.
Disassembly and Reassembly _ 31
Part Figure Description
ROTOR LOWER
/ ASSY DUCT
NOZZLE
Sump
Guide of Holder
Bottom of Holder
Rib
[ASSEMBLY]
1. Put the HOLDER ROTOR LOWER on the SUMP.
CAUTION
Pay attention to assemble the HOLDER ROTOR
LOWER correctly. There’re risks of leakage or
poor performance when it’s misassembled.
2. Assemble the ASSY DUCT NOZZLE to hooks and
on the HOLDER ROTOR LOWER.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Make sure to reassemble to correct location.
There’re risks of leakage or poor performance
when it’s misassembled.
32 _ Disassembly and Reassembly
Part Figure Description
ROTOR LOWER
/ ASSY DUCT
NOZZLE
3. Fasten 2 screws to t the ASSY DUCT NOZZLE.
- Screws: DD81-02718A / 2 pcs
4. Put the ROTOR LOWER onto the HOLDER
ROTOR LOWER.
Disassembly and Reassembly _ 33
2-11. ASSY ROTOR MIDDLE
- ASSY ROTOR MIDDLE : DD82-01894A / SVC ASSY-ROTOR MIDDLE
Part Figure Description
ASSY ROTOR
MIDDLE
[DISASSEMBLY]
1. Open the dishwasher’s DOOR, and take off the
BASKET MIDDLE.
2. Release 2 hooks to take off ASSY ROTOR MIDDLE
from the BASKET MIDDLE.
- ASSY-ROTOR MIDDLE : DD82-01894A
CAUTION
Be careful not to be broken the hooks.
[ASSEMBLY]
1. Reassembly is the reverse order of disassembly.
long short
long
short
To disassemble the ROTOR MIDDLE only, loosen
the HOLDER ROTOR MIDDLE to counter-clockwise
direction.
Make sure to t the hook to the right location of
ROTOR MIDDLE.
34 _ Disassembly and Reassembly
2-12. COARSE FILTER / FINE FILTER / MICRO FILTER
- FILTER COARSE : DD81-02452A / SVC FILTER COARSE
- FILTER MICRO : DD81-02453A / SVC FILTER MICRO
- FILTER FINE : DD81-02454A / SVC FILTER FINE
Part Figure Description
COARSE FILTER
/ FINE FILTER /
MICRO FILTER
[DISASSEMBLY]
1. Turn the COARSE FILTER counter-clockwise to
unlock the lter assembly.
2. Separate the lters by releasing hooks.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
Make sure to direction of MICRO FILTER when
reassemble lters. (Hooks must face upward)
Coarse
lter
Fine lter Micro
lter
[ASSEMBLY]
Reassembly is the reverse order of disassembly.
FILTER COARSE : DD81-02452A
FILTER MICRO : DD81-02453A
FILTER FINE : DD81-02454A
CAUTION
Make sure the COARSE FILTER is closed
properly.
A loose cover can reduce the ltering
performance.
Disassembly and Reassembly _ 35
2-13. BASKET 3RD / ASSY ROLLER 3RD / HANDLE BASKET
- BASKET 3RD : DD82-01893A (DW60A8070* models) , DD82-01893B (DW60A8060*,DW60A8050* models) /
SVC ASSY-BASKET 3RD
Part Figure Description
BASKET 3RD /
ASSY ROLLER
3RD/ HANDLE
BASKET
BASKET
3RD TRAY
[DISASSEMBLY]
1. Lift up the BASKET 3RD TRAY and separate it.
ASSY ROLLER
3RD 2. Release the hook of ASSY ROLLER 3RD xed to
the WIRE FRAME 3RD and separate it.
3. Remove the HANDLE BASKET by lifting the 2 RIB.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Be careful not to be broken the hooks.
[ASSEMBLY]
1. Assemble the BASKET 3RD with ASSY ROLLER
3RD and HANDLE BASKET together.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Be careful not to be broken the hooks.
36 _ Disassembly and Reassembly
2-14. BASKET MIDDLE / ASSY ADJUSTER
- BASKET MIDDLE : DD82-01887A (DW60A8070* models) , DD82-01887B (DW60A8060*,DW60A8050* models) /
DD82-01887C (DW60A8040* models) SVC ASSY-BASKET UPPER
Part Figure Description
BASKET
MIDDLE / ASSY
ADJUSTER
[DISASSEMBLY]
1. Open the dishwasher’s DOOR, and take off the
BASKET MIDDLE.
Please refer to the section of ‘ASSY ROTOR
MIDDLE’ for disassembly of rotor middle.
ASSY BRACKET
ADJUSTER
ASSY Adjuster
2. Release 4 hooks of ASSY ADJUSTER(at each
side) to release them from the BASKET MIDDLE.
- ASSY-BRACKET ADJUSTER-LEFT : DD82-01896A
- ASSY-BRACKET ADJUSTER-RIGHT : DD82-01897A
- ASSY ADJUSTER L : DD82-01958A
- ASSY ADJUSTER R : DD82-01959A
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Be careful not to be broken the hooks.
[ASSEMBLY]
1. Assemble the BASKET MIDDLE with ASSY
ADJUSTER and ASSY BRACKET ADJUSTER
together.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Be careful not to be broken the hooks.
Disassembly and Reassembly _ 37
2-15. BASKET MIDDLE / GUIDE TINE / HANDLE BASKET
- WIRE FOLDING : DD81-03173A / SVC WIRE FOLDING
- HOLDER TINE-UP : DD81-03186A / SVC HOLDER TINE-UP
- GUIDE BUTTON : DD81-03174A / SVC GUIDE BUTTON
- HOLDER GUIDE TINE : DD81-03175A / SVC HOLDER GUIDE TINE
- HOLDER GUIDE TINE-UP : DD81-03177A / SVC HOLDER GUIDE TINE-UP
- WIRE GUIDE TINE : DD81-03176A / SVC WIRE GUIDE TINE
Part Figure Description
BASKET MIDDLE/
HANDLE
BASKET/
WIRE FOLDING/
HOLDER TINE-
UP/
HOLDER GUIDE
TINE/ GUIDE
BUTTON /
HOLDER GUIDE
TINE-UP
HANDLE BASKET
[DISASSEMBLY]
1. Remove the HANDLE BASKET by lifting the 2 RIB.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Be careful not to be broken the hooks.
WIRE FOLDING
HOLDER TINE-UP
2. Release the 2 HOLDER TINE-UP hooks and
separate the WIRE FOLDING from the BASKET
MIDDLE.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Be careful not to be broken the hooks.
38 _ Disassembly and Reassembly
Part Figure Description
BASKET MIDDLE/
HANDLE
BASKET/
WIRE FOLDING/
HOLDER TINE-
UP/
HOLDER GUIDE
TINE/ GUIDE
BUTTON /
HOLDER GUIDE
TINE-UP
GUIDE BUTTON
HOLDER GUIDE TINE
3. Release the 4 hooks of HOLDER GUIDE TINE and
separate it from the BASKET MIDDLE.
4. Push the GUIDE BUTTON to separate it from the
HOLDER GUIDE TINE.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Be careful not to be broken the hooks.
1
2
HOLDER GUIDE TINE-UP
WIRE GUIDE TINE
5. Release the hook of HOLDER GUIDE TINE-UP
to separate WIRE GUIDE TINE from BASKET
MIDDLE.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Be careful not to be broken the hooks.
[ASSEMBLY]
Reassembly is the reverse order of disassembly.
Carefully assemble the assembly position of
HOLDER TINE-UP and HOLDER GUIDE TINE-UP.
Disassembly and Reassembly _ 39
2-16. BASKET LOWER
- BASKET LOWER : DD82-01886A (DW60A8070* models) , DD82-01886B
(DW60A8060*,DW60A8050*,DW60A8040* models) / SVC ASSY-BASKET LOWER
Part Figure Description
BASKET LOWER
[DISASSEMBLY]
1. Open the dishwasher’s DOOR, and take off the
BASKET LOWER.
2. Remove the HANDLE BASKET by lifting the 2 RIB.
3. Release hook to take off ROLLER BASKET.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
Wire tine
Holder tine low Holder wire
L/R
4. Release the hook to remove HOLDER WIRE L/R
and HOLDER TINE LOW, and separate the WIRE
TINE.
[ASSEMBLY]
1. Reassembly is the reverse order of disassembly.
40 _ Disassembly and Reassembly
2-17. RAIL BASKET / HOLDER RAIL REAR
- HOLDER RAIL MIDDLE REAR : DD81-02768A / SVC HOLDER RAIL MIDDLE REAR
- RAIL BASKET LEFT : DD81-02766A / SVC RAIL MID-LEFT
- RAIL BASKET RIGHT : DD81-02767A / SVC RAIL MID-RIGHT
Part Figure Description
RAIL BASKET
& HOLDER RAIL
REAR
Holder Rail Rear
[DISASSEMBLY]
1. Take off the HOLDER RAIL REAR by pulling back
with releasing the hook.
- HOLDER RAIL MIDDLE REAR : DD81-02768A
Rail Basket Left
Rail Basket Right
2. Take off the RAIL BASKET.
- RAIL MID-LEFT : DD81-02766A
- RAIL MID-RIGHT : DD81-02767A
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
[ASSEMBLY]
1. Put the RAIL BASKET on the ROLLER RAIL.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Make sure that the direction of RAIL BASKET
when it’s reassembled. The front part of RAIL
BASKET faces upward.
2. Assemble the HOLDER RAIL REAR to RAIL
BASKET.
CAUTION
Make sure to lock the hook to hole of RAIL
BASKET.
Disassembly and Reassembly _ 41
2-18. COVER PLINTH
- COVER PLINTH : DD81-01650A (*FW models), DD81-01650B (*FS models) / SVC COVER PLINTH
Part Figure Description
COVER PLINTH
(Only for Free
standing models /
DW6*R70**F*)
[DISASSEMBLY]
1. Open the DOOR to 90˚, and release 2 screws.
- Screws: DD81-02694A / 2 pcs
WARNING
Be sure to remove the power plug before
servicing.
2. Release the holder of COVER PLINTH slightly from
the hook by at-head screw driver, and pull up the
COVER PLINTH.
3. Do same work at the opposite side.
- COVER PLINTH : DD81-01650A/DD81-01650B
[ASSEMBLY]
1. Assemble the COVER PLINTH to BASE.
CAUTION
Insert the COVER PLINTH inside the holder.
2. Open the DOOR to 90˚, Fasten 2 screws.
- Screws: DD81-02694A / 2 pcs
42 _ Disassembly and Reassembly
2-19. COVER TOP
- COVER TOP : DD81-02552D (*FW models), DD81-02552C (*FS models) / SVC TOP COVER
Part Figure Description
COVER TOP
(Only for Free
standing models /
DW60A80**F*)
[DISASSEMBLY]
1. Release 2 screws.
- Screws: DD81-02692A / 2 pcs
WARNING
Be sure to remove the power plug before
servicing.
1
2
2. Pull the COVER TOP backward to release hooks,
and take it off upward.
-TOP COVER : DD81-02552C/DD81-02552D
1
2
Hook Of Cover Top
Guide Of Cover Top
Tub Frame
[ASSEMBLY]
1. Put the COVER TOP on the top of dishwasher, and
push it forward to assembly.
Pay attention to lock the hooks(COVER TOP) to TUB
FRAME.
2. Fasten 2 screws.
- Screws: DD81-02692A / 2 pcs
Disassembly and Reassembly _ 43
2-20. SIDE PANEL / GUIDE TUB TOP / COVER TUB REAR
- GUIDE TUB TOP : DD81-02733A / SVC GUIDE TUB TOP
- HOUSING-LEFT : DD81-02928B (*BB, *IB models), DD81-02880A (*FS models). DD81-02880C (*FW models) /
SVC HOUSING-LEFT
- HOUSING_RIGHT : DD81-02929B (*BB, *IB models), DD81- 02881A (*FS models). |DD81-02881C (*FW models) /
SVC HOUSING-RIGHT
- COVER TUB REAR : DD81-03043A (*BB, *IB models), DD81-02734A (*US, *FS, *FW models) / SVC COVER TUB REAR
Part Figure Description
SIDE PANEL/
GUIDE TUB TOP/
COVER TUB
REAR
(DW60A80**F*)
[DISASSEMBLY]
1. Release 2 screws.
- Screws: DD81-02692A / 2 pcs
WARNING
Be sure to remove the power plug before
servicing.
1
2
2. Pull the COVER TOP backward to release hooks,
and take it off upward.
A
B
Cover Tub Rear
B
Guide Tub Top
3. Release Screws.
- Front side
‧ Type A: DD81-02693A / 4 pcs
- Rear side
‧ Type B: DD81-02694A / 4 pcs
- Top side
‧ Type B: DD81-02694A / 2 pcs
44 _ Disassembly and Reassembly
Part Figure Description
SIDE PANEL/
GUIDE TUB TOP/
COVER TUB
REAR
(DW60A80**F*)
Not to get
stuck
Could be dented
Hook
4. Take the SIDE PANEL off a little, just enough not to
get stuck to TUB FRAME.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
CAUTION
Be careful not to be dented SIDE PANEL because
of hook.
Side Panel Left Side Panel Right
Guide Tub Top
Cover Tub Rear
5. Pull the SIDE PANEL off from the COVER PLINTH.
GUIDE TUB TOP and COVER TUB REAR are
disassembled together.
- GUIDE TUB TOP : DD81-02733A
- HOUSING-LEFT : DD81-02928B/DD81-02880A/
DD81-02880C
- HOUSING-RIGHT : DD81-02929B/DD81-02881A/
DD81-02881C
- COVER TUB REAR : DD81-03043A/DD81-02734A
[ASSEMBLY]
1. Assemble the GUIDE TUB TOP and COVER TUB
REAR to back of dishwasher.
CAUTION
They are not xed without SIDE PANEL.
Recommend to work by 2 people.
Disassembly and Reassembly _ 45
Part Figure Description
SIDE PANEL/
GUIDE TUB TOP/
COVER TUB
REAR
(DW60A80**F*)
2. Put the hook of SIDE PANEL into the COVER
PLINTH.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
On The Tub
Frame
On The Guide
Tub Top
Could be dented
Hook
3. Assemble the SIDE PANEL left & right to each side.
CAUTION
Be careful not to be dented SIDE PANEL because
of hook.
Front
Top
Rear
4. Make sure to t the SIDE PANEL correctly.
46 _ Disassembly and Reassembly
Part Figure Description
SIDE PANEL/
GUIDE TUB TOP/
COVER TUB
REAR
(DW60A80**F*)
A
B
Cover Tub Rear
B
Guide Tub Top
5. Fasten Screws.
- Front side
‧ Type A: DD81-02693A / 4 pcs
- Rear side
‧ Type B: DD81-02694A / 4 pcs
- Top side
‧ Type B: DD81-02694A / 2 pcs
CAUTION
Fasten the screws that was assembled to origin
location. Don’t assemble to other locations.
1
2
Hook Of Cover Top
Guide Of Cover Top
Tub Frame
6. Put the COVER TOP on the top of dishwasher, and
push it forward to assembly.
Pay attention to lock the hooks(COVER TOP) to TUB
FRAME.
7. Fasten 2 screws.
- Screws: DD81-02692A / 2 pcs
Disassembly and Reassembly _ 47
Part Figure Description
SIDE PANEL/
GUIDE TUB TOP/
COVER TUB
REAR
(DW60A80**BB/
DW60A80**IB/
DW60A80**U*
models)
A
B
B
Cover Tub Rear
C
B
Guide Tub Top
[DISASSEMBLY]
1. Release Screws.
- Front side (Type A): DD81-02693A / 4 pcs
(Type B): DD81-02694A / 2 pcs
- Rear side (Type B): DD81-02694A / 4 pcs
(Type C): DD81-02692A / 2 pcs
- Top side (Type B): DD81-02694A / 2 pcs
Side Panel Left Side Panel Right
Guide Tub Top
Cover Tub Rear
2. Disassemble the SIDE PANEL left & right from
each side. GUIDE TUB TOP and COVER TUB
REAR are disassembled together.
- GUIDE TUB TOP : DD81-02733A
- HOUSING-LEFT : DD81-02928B/DD81-02880A/
DD81-02880C
- HOUSING_RIGHT : DD81-02929B/DD81-02881A/
DD81-02881C
- COVER TUB REAR : DD81-03043A/DD81-02734A
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
48 _ Disassembly and Reassembly
Part Figure Description
SIDE PANEL/
GUIDE TUB TOP/
COVER TUB
REAR
(DW60A80**BB/
DW60A80**IB/
DW60A80**U*
models)
[ASSEMBLY]
1. Assemble the GUIDE TUB TOP and COVER TUB
REAR to back of dishwasher.
CAUTION
They are not xed without SIDE PANEL.
Recommend to work by 2 people.
On The Tub
Frame
On The Guide
Tub Top
2. Assemble the SIDE PANEL left & right to each side.
WARNING
Do not this work without safety gloves. It can
cause injury from sharp edge.
A
B
B
Cover Tub Rear
C
B
Guide Tub Top
3. Fasten screws.
- Front side (Type A): DD81-02693A / 4 pcs
(Type B): DD81-02694A / 2 pcs
- Rear side (Type B): DD81-02694A / 4 pcs
(Type C): DD81-02692A / 2 pcs
- Top side (Type B): DD81-02694A / 2 pcs
Disassembly and Reassembly _ 49
3. CHECKPOINTS AFTER FINISHING A SERVICE
1 Check the safety device
Check the operation of the door lock switch. Make sure that it is locked while the dishwasher is running and that it is
unlocked when the dishwasher stops.
2. Use authenticated parts only
If any part is not authenticated, replace it with an authenticated part.
3. Handling wires
Check if any wires are loose or too tight, if they are connected correctly, if they are well bound with tape, and if they
are properly clamped.
4. The state of screws and nuts
Check if the screws and nuts are fastened correctly. Check whether they are fastened with the specied torque.
5. Remove foreign material
Check whether any foreign material such as soil, wire scraps and screws are in the dishwasher. (Check whether any
foreign material is entering through the sump into the disposer.)
6. Check for water leakage
Check whether there is water leakage from the hose connector, door, case sump (drain motor, circulation motor,
heater, thermistor, distributor motor), and the water supply/drain hoses.
7 Check the power cable
Check if there is any damage to the power cable or power outlet. Check that the power capacity is appropriate.
8. Check leveling
Check whether the dishwasher is level.
9. Check the installation location
Check whether the installation location is at and stable.
© 2021 Samsung Electronics Co.,Ltd.
All rights reserved.
Printed in Korea
GSPN (GLOBAL SERVICE PARTNER NETWORK)
Area Web Site
Eurpoe, CIS, Mideast & africa gspn1.samsungcsportal.com
Asia gspn2.samsungcsportal.com
North & Latin America gspn3.samsungcsportal.com
China china.samsungportal.com
This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law.