Samsung HRD-442-2TB User Manual
Displayed below is the user manual for HRD-442-2TB by Samsung which is a product in the Digital Video Recorders (DVR) category. This manual has pages.
Related Manuals
HRD-442/842/1642
4/8/16 CHANNEL DVR
User Manual
Copyright
©2017 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of
their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly,
without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin reserves the right
to change the contents of this document without prior notice.
Design and speci cations are subject to change without prior notice.
The default administrator ID is “admin”, and the password must be set when the user log in at the rst time.
Set password for your wireless network if you use the product with a wireless router. Being not protected with password or using the
default wireless router password may expose your video data to potential threat.
To prevent from your personal information being exposed, please change your password every 3 months. Note that the security and
other related issues caused by careless management of password shall be be in the charge of the user.
4/8/16 Channel DVR
User Manual
English _3
● OVERVIEW
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil
constituents as they may deform or cause damage to the product.)
7) Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods
of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
overview
4_ overview
overview
CALIFORNIA USA ONLY
This Perchlorate warning applies only to primary CR (Manganese Dioxide)
Lithium coin cells in the product sold or distributed ONLY in California USA.
“Perchlorate Material - special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.”
BEFORE START
This manual provides operational information necessary for using the product and contains a description about each
component part and its function as well as menu or network settings.
You have to keep in mind the following notices :
• Hanwha Techwin retains the copyright on this manual.
• This manual cannot be copied without Hanwha Techwin’s prior written approval.
• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of
instructions mentioned in this manual.
• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be
removed from the unit.
• Before installing additional HDD or connecting the SATA device to this product, check if it is compatible with the
product.
Warning
Battery
It is essential that when changing the battery in the unit, the replacement battery must be of the same type
otherwise there may be a possibility of an explosion.
The following are the specifications of the battery you are using now.
• Normal voltage : 3V
• Normal capacity : 220mAh
• Discharge Current : 0.2mA
• Operating temperature : -20°C ~ +85°C
(-4°F ~ +185°F)
Caution
• Connect the power cord into a grounded outlet.
• The Mains plug is used as a disconnect device and shall stay readily operable at any time.
• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the
Instructions.
System Shutdown
Turning off the power while the product is in operation, or undertaking improper actions may cause damage
or malfunction to the hard drive or the product.
To safely cut off power, press the front Power button on the product to display the confirmation message.
Click <OK> and then unplug the power cable.
You may want to install a UPS system for safe operation in order to prevent damage caused by an
unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)
English _5
● OVERVIEW
Operating Temperature
The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).
This product may not work properly if you run right after a long period of storage at a temperature below the
guaranteed one.
Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand
at room temperature for a period.
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).
Likewise, the hard drive may not work at a temperature below the guaranteed one.
Ethernet Port
This equipment is in door use and all the communication wirings are limited to inside of the building.
Security Precautions
The default administrator ID is “admin”, and the password must be set when the user log in at the first time.
Set password for your wireless network if you use the product with a wireless router. Being not protected with
password or using the default wireless router password may expose your video data to potential threat.
To prevent from your personal information being exposed, please change your password every 3 months.
Note that the security and other related issues caused by careless management of password shall be be in the
charge of the user.
6_ overview
overview
CONTENTS
OVERVIEW
3
3 Important Safety Instructions
4 Before Start
6 Contents
8 Features
12 Part Names and Functions (Front)
15 Part Names and Functions (Rear)
17 Remote Control
INSTALLATION
19
19 Checking the installation environment
20 Rack Installation
21 Installing The HDD
CONNECTING WITH OTHER DEVICE
26
26 Connecting External Devices
28 Connecting the Network
LIVE
30
30 Getting Started
33 Live Screen Configuration
38 Live Mode
41 Spot Out
41 Zoom
42 Audio ON/OFF
42 Freeze
43 Event Monitoring
MAIN MENU
44
44 System Setup
54 Setting the Device
64 Setting the Recording
67 Setting the Event
70 Backup
72 Network Configuration
85 Controlling a PTZ device
English _7
● OVERVIEW
SEARCH & PLAY
88
88 Search
91 Playback
WEB VIEWER
93
93 Introducing Web Viewer
94 Connecting Web Viewer (Windows)
96 Using Live Viewer (Windows)
101 Controlling a Connected PTZ Camera
104 Using Search Viewer
107 Viewer Setup
119 Information
120 Connecting Web Viewer (Mac)
122 Using Live Viewer (Mac)
123 Mobile Viewer
BACKUP VIEWER
124
124 SEC Backup Viewer
APPENDIX
126
126 Product Specification
130 Product Overview
133 Default Setting
137 Troubleshooting
140 Open Source Announcement
8_ overview
overview
FEATURES
The product compresses camera inputs from 4/8/16 channels with H.264 video codec, and supports simultaneous
recording and playback of 4/8/16-channel audio input to/from HDD.
These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video and
audio data.
• Provides a convenient User Interface
•
4/8/16
CH Composite Input Connectors
• Supports CIF/2CIF/4CIF/WD1/720P/1080P/4M recording formats
• With the network specific codec, network transfer enabled regardless of the recording conditions
• Display of HDD information and status by using HDD SMART
• CODEC performance : 4CH
NTSC : Up to 60fps@4MP / PAL : Up to 50fps@4MP
NTSC: Up to 120fps@1920 x 1080 / PAL : Up to 100fps@1920 x 1080
8CH
NTSC : Up to 120fps@4MP / PAL : Up to 100fps@4MP
NTSC : Up to 240fps@1920 x 1080 / PAL : Up to 200fps@1920 x 1080
16CH
NTSC : Up to 240fps@4MP / PAL : Up to 200fps@4MP
NTSC : Up to 480fps@1920 x 1080 / PAL : Up to 400fps@1920 x 1080
• HDD overwrite function
• Mass storage HDD backup through high-speed USB 3.0, 2.0
• Simultaneous Record and Playback of 4/8/16-channel video data
• Various Search Modes (Time, Event, Backup, POS, Motion Detection)
• Various Recording Modes (Manual, Event, Scheduled Recording)
• Alarm Interface
• Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer
• Supports coaxial and RS-485 protocols
• Tampering Detection
Standards Approvals
J Any changes or modifications in construction of this device which are not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
M This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
English _9
● OVERVIEW
Package Contents
Please unwrap the product, and place the product on a flat place or in the place to be installed.
Please check the following contents are included in addition to the main unit.
M The appearance of the components may differ from the image shown.
Accessory category and quantity may differ depending on sales region.
For some regions, HDD is not pre-installed. HDD Fixing Screw, SATA Power Cable, SATA data cable and SATA power/data
cable quantity vary depending on the model.
HRD-442
'9
6516
',*,7$/9,'(25(&25'(5
REC HDD ALARM
NETWORK BACKUP
POWER
DVR Adapter
Power Cable Mouse Remote Control /
Remote Control Battery (AAA)
User Manual or Quick Manual Network Viewer Software /
User Manual CD Bracket Rack
Bracket Fixing Screw Terminal Block (10 pin)
10_ overview
overview
HRD-842
USB
DVR Power Cable
Mouse User Manual or Quick Manual Remote Control /
Remote Control Battery (AAA)
Network Viewer Software /
User Manual CD Terminal Block (15 pin) Terminal Block (20 pin)
Bracket Fixing Screw Bracket Rack HDD Fixing Screw
(For models having no installed HDD)
SATA Power Cable
(For models having no installed HDD)
SATA Data Cable
(For models having no installed HDD)
English _11
● OVERVIEW
HRD-1642
USB
DVR Power Cable
Mouse User Manual or Quick Manual Remote Control /
Remote Control Battery (AAA)
Network Viewer Software / User Manual CD
Terminal Block (15 pin) Terminal Block (20 pin)
Bracket Fixing Screw Bracket Rack HDD Fixing Screw
(For models having no installed HDD)
SATA Data Cable
(For models having no installed HDD)
SATA Power Cable
(For models having no installed HDD)
12_ overview
overview
PART NAMES AND FUNCTIONS (FRONT)
HRD-442
HRD-842
HRD-1642
Part Names Functions
Channel Used to select channel numbers directly in the Live Mode, or numbers in the numeric input mode.
b
REC Starts or ends the recording.
/Step Rewind (
) : Used for backward frame-by-frame search while in PAUSE.
Fast Rewind () : Used for quick backward search while in Play. (2x-64x)
Stop : Used to stop the playback.
►/Play/Pause : Used to pause or resume the screen.
/Fast Forward () : Used for quick forward playback. (2x-64x)
Step Forward (
) : Used for forward frame-by-frame search while in PAUSE.
USB
b
c
USB
b
c
'9
6516
',*,7$/9,'(25(&25'(5
REC HDD ALARM
NETWORK BACKUP
POWER
c
English _13
● OVERVIEW
Part Names Functions
cLED Indicator
REC : Lights on when recording is in progress.
HDD : Displays the normal access to HDD.
Upon access to HDD, LED repeats on and off.
ALARM : Lights on when an event occurs.
NETWORK : Displays both network connection and data transfer status.
BACKUP : Stays ON when backup is in operation. (HRD-442)
POWER : Displays the power ON/OFF status.
Direction /
Select Button
Used to change a value or move the cursor up/down/left/right (◄ ►).
Selects a menu item or executes the selected menu.
Jog shuttle
When a scroll bar appears in each menu, acts as a scrolling.
In Play mode, - Jog : Pauses the playback and steps backward or forward.
- Shuttle : Fast playback forward or backward.
Power Used to turn the DVR ON/OFF.
Functions only if the button was held for 3 seconds.
USB Port Connects the USB devices.
MODE Each time you press the button in Live mode, the screen mode will be switched in sequence.
Each time you press the button in play mode, the screen mode will be switched in sequence.
AUDIO Sets Audio ON/OFF.
ALARM Cancels the ALARM LED and the audible alarm when the alarm is going off, and to remove the icon.
MENU/'Either goes to the system menu screen or moves to the upper menu from the lower menu.
ENTER Runs selected menu function.
Camera Control
ZOOM :
Digital zoom. (Magnification ratio varies depending on camera’s resolution. The higher the
resolution, the greater the magnification.)
FREEZE : Runs the FREEZE function in the Live Mode.
BACKUP : Runs the BACKUP function.
SEARCH : Goes to the search screen.
Remote
Reception System Receive the signal from the remote control.
14_ overview
overview
Using the jog shuttle
Jog starts from the right point and shuttle starts from the left point.
< Jog >
In play mode, DVR playback steps forward video by 1 frame. In play mode, DVR playback steps backward video by 1 frame.
< Shuttle >
In play mode, DVR plays fast forward. In play mode, DVR plays fast reverse.
English _15
● OVERVIEW
PART NAMES AND FUNCTIONS (REAR)
HRD-442
HRD-842
HRD-1642
Part Names Functions
AUDIO IN Audio input signal port (RCA jack) and port for optional audio extension cable.
bAUDIO OUT Audio Signal Output Port (RCA jack).
cVIDEO IN Video Signal Input Port (BNC type connector).
SPOT BNC type of output port for the Spot signal.
CH1
CH3
CH2
CH4
CONSOLE
SERIAL
1234
5678
AUDIO IN CH5 ~ CH8
VIDEO IN
AUDIO OUT
AUDIO IN
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
12345678
ALARM IN
NO CONNECTION
G G
HDMI eSATA
VGA OUT
USB
NETWORK
b c
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
CONSOLE HDMI eSATA
VGA OUT
SERIAL
12345678
9 10111213141516
12345678 9 101112 1314 1516
ALARM IN
G G G G
NETWORK USB
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
b c
&+ &+
&+ &+
6327
&+ &+
&+ &+ +'0, 1(7:25.
VGA OUT
SERIAL
CONSOLE
POWER
DC12V
1
12
234
ALARM IN
ALARM OUT
G
TX
NO
COM
COM
NO
NC
RX
ALARM
RESET
G
AUDIO OUT
HD VIDEO IN AUDIO IN
b c
16_ overview
overview
Part Names Functions
Power Power connection port.
eSATA Ports used for external storage device connections.
USB Connects the USB devices.
NETWORK NETWORK connector port.
VGA OUT Composite Video Signal Output Port (VGA type connector).
HDMI HDMI connector port.
ALARM
-ALARM IN : Alarm input ports.
HRD-442 : 1~4 CH
HRD-842 : 1~8 CH
HRD-1642 : 1~16 CH
-ALARM OUT : Alarm output ports.
HRD-442 : 1~2 CH
HRD-842/1642 : 1~4 CH
-ALARM RESET : Alarm Reset port.
RS-485 Used to establish RS485 communications. (TX+, TX-, RX+, RX-)
SERIAL Serial port for connecting to a POS device.
M [CONSOLE] is designed for the service repair purpose only.
In order to avoid high-speed signal crosstalk, suggest that the cable length between adjacent video channels is less than
300m. (based on 75-5 coaxial cable)
English _17
● OVERVIEW
REMOTE CONTROL
POWER
Displays the Exit pop up screen.
REC
Starts or ends the live recording.
ID
Sets the ID of the system.
Select 2 digits from 0 ~ 9 while pressing the ID Key.
VIEW
Runs the View function in the PTZ mode.
BACKUP
Displays the Backup Menu.
RETURN
Returns to the previous screen.
REC LOCK
Selects the recording lock function.
AUDIO
Turns Audio on/off.
Up/Down/Left/Right(▲▼◄ ►)/ENTER
Moves the cursor up/down/left/right, and runs the
Select Menu.
Move Frame
While paused, moves to the previous/next frame.
SCROLL ,.
Moves the menu scroll.
FR, STOP, PLAY/PAUSE, FF
MODE
Changes the screen mode.
MENU
Goes to the system menu screen.
ZOOM
Runs the digital zoom (x2) function.
NUMBER [0~+10]
Used as the numeric input keys, or displays a single
channel.
T/W
Zooms in or out.
PTZ
Displays or ends PTZ.
SEARCH
Displays the search menu.
PRESET
Displays the Preset Setup.
FREEZE
Freezes the screen temporarily.
Skip Backward (by unit time),
Slow Rewind, Slow Forward,
Skip Forward (by unit time)
ALARM
Cancels the Alarm.
18_ overview
overview
Using the Numeric buttons
CHANNEL 1–9 Press each button between 1 to 9.
CHANNEL 10 Press the [+10] button first, then press the 0 button again within 3 seconds.
CHANNEL 11–16 Press the [+10] button first, then press any number between 1 to 6 within 3 seconds.
Changing the Remote Control ID
Remote control’s ID and DVR’s ID should be matched for proper operation.
1. Press the [ID] button of the remote control and check the ID displayed on the DVR screen.
The factory default ID of the remote control is 00.
2. Enter 2 digits of your selection in order, while pressing the [ID] button of the remote control.
3. When ID input is done, press the [ID] button of the remote control again to check the setting.
M
If you want to change the remote control ID to 08: Press 0 and 8 in order while the [ID] button of the remote control is pressed.
For changing the ID of remote device, refer to “Remote Devices”. (Page 60)
English _19
●INSTALLATION
installation
Please take note of the followings before using this product.
• Do not use the product outdoor.
• Do not spill water or liquid in the connection part of the product.
• Do not impose the system to excessive shock or force.
• Do not pull out the power plug forcefully.
• Do not disassemble the product on your own.
• Do not exceed the rated input/output range.
• Use a certified power cord only.
• For the product with an input ground, use a grounded power plug.
CHECKING THE INSTALLATION ENVIRONMENT
This product is a top-notch security device that is equipped with a
high-capacity HDD and other key circuit boards.
When the temperature rises inside the product, the product may
breakdown and the product life be shortened. Please pay attention to
the following recommendations before installation.
When mounting the product on a rack, comply with the following instructions.
1. Please ensure that the rack inside is not sealed.
2. Please ensure the air is circulated through the inlet/outlet as shown in the picture.
3. If you pile up the prudcts or other rack-mount devices as shown in figure 2, secure
room for ventilation or install a vent.
4.
For natural air convection, place the inlet at the bottom of the rack and the outlet on top.
5. It is strongly recommended that a fan motor is installed at the inlet and the outlet for
air circulation. (Please fit a filter at the inlet to screen dust or foreign substances.)
6. Please maintain the temperature inside the rack or surrounding areas between 0°C
~ 40°C (32°F ~ 104°F) as shown in the figure 1.
Rack Mount Instructions - The following or similar rack-mount instructions are included
with the installation instructions :
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment may be greater than room
ambient. Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified by
the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that
the amount of air flow required for safe operation of the equipment is not
compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such
that a hazardous condition is not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should
be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
[Figure 1]
Temperature Unit: ºC
One Year: 24HR X 365 DAY =8,760 HR
Life (Unit: HOURS)
[Figure 2]
USB
USB
USB
USB
USB
USB
USB
20_ installation
installation
RACK INSTALLATION
Install the Bracket-Rack as shown in the figure, and then fasten the
screws on both sides (2 screws on each side).
Remove the screws on the left and right side of the DVR before installation.
Fix the screws not to be loosened by vibrations.
Cautions when Installing in the Rack
To install multiple DVRs in the rack, make sure to separate the FOOT at the bottom of each DVR.
1. There are four FOOTs at the bottom of a DVR.
Press the projected parts at both-ends of each “FOOT”
and turn it counterclockwise.
2. “FOOT” is separated from the main body when it is turned
to the end of fastening groove.
<Separation> <Installation>
English _21
●INSTALLATION
INSTALLING THE HDD
Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product
damage.
Please consult your provider for further information on HDD installation since improper installation or settings may
damage the product.
Make sure to unplug the power cord from the wall outlet before proceeding with the installation.
J Cautions for data loss (HDD care)
Please pay attention so that the data inside the HDD is not damaged.
Before adding a HDD, please check the compatibility with this product.
HDD is vulnerable to malfunction due to its sensitive nature especially against shock when operating.
Please ensure that the HDD is free from such shock.
We are not liable for any damage to the HDD incurred by user’s carelessness or miss use.
Cases might cause damage to HDD or recorded data
To minimize the risk of data loss from a damaged HDD, please backup data as often as possible.
If exposed to shock when disassembling or installing, data stored in the hard disk may be damaged.
A sudden power failure or turning off the product while in HDD operation may damage the hard disk drive.
HDD or files stored inside may be damaged if the main body is moved or impacted during the HDD operation.
Cautions on HDD installation
1. When adding a new HDD, make sure to fasten screws tightly and use appropriate parts if required to fix
the HDD. Otherwise, the product may be damaged or does not operate properly.
2. Please check the HDD compatibility before adding a HDD.
Please contact your nearest dealer to obtain the list of compatible devices.
Installing the HDD
J If the installed HDD had been used with other devices, it will be automatically formatted.
• If installing HDDs to HRD-442
1. Unfasten the screws on the side and in the rear and
remove the cover.
22_ installation
installation
2. Unfasten the screws on the HDD bracket and
remove the bracket.
Press the handle on both sides of the bracket and pull it
forward. The main body and the bracket will separate.
3. First combine the HDD bracket and one side of the
HDD and open the bracket on the other side to
mount the HDD.
Insert the screws from the HDD bracket into the HDD screw
hole.
4. Press the bracket where the HDD is mounted and
fix it in with screws.
English _23
●INSTALLATION
5. Close the cover and use the screws to fix it.
• If installing HDDs to HRD-842/1642
The following figures are based on Model HRD-1642.
1. First, loosen the screws on both sides and remove
the cover.
2. Loosen the screws (x4) in the left/right and upper
sides and remove the upper brackets.
1
NO
COM COM COM COM
NCNO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
SERIAL
12345678
910 11 12 13 14 15 16
12345678910111213141516
ALARM IN
GG
GG
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
eSATA
CONSOLE USB
NETWORK
HDMI
VGA OUT
Bracket
USB
24_ installation
installation
3.
Install HDDs (x4) on the upper bracket and fix them
with screws.
4. Connect the cable to the HDD by matching the
HDD SATA/power cable number to the HDD
position number on the bracket.
1
NO
COMCOMCOMCOM
NCNONO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
SERIAL
12345678
910
1112 1314 15 16
12345678910111213141516
ALARM IN
GG
GG
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
eSATA
CONSOLEUSB
NETWORK
HDMI
VGA OUT
Bracket
1
NO
COM COM COM COM
NCNONO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
SERIAL
12345678
910 11 12 13 14 15 16
123456789101112131415 16
ALARM IN
GG
GG
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
eSATA
CONSOLE USB
NETWORK
HDMI
VGA OUT
Bracket
English _25
●INSTALLATION
5. Mount the bracket on which an additional HDD is
mounted to the DVR and fasten it with screws, and
then connect the SATA/power cable to the
connector with the corresponding number on the
main board.
For the HDD position on the bracket, please refer to the
figure below.
M
Please don’t pull off the cables with force, press the
connector gently before removing HDD.
6. Check if the connectors are properly connected and
there is no problem with wiring, and close the cover
and fix it with screws.
USB
1
NO
COM COM COMCOM
NCNO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
SERIAL
12345678
91011 12 13 14 15 16
12345678910111213141516
ALARM IN
GG
GG
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
eSATA
CONSOLE USB
NETWORK
HDMI
VGA OUT
1
2
63
4
7
5
8
1
2
3
4
5
6
7
8
< HRD-1642 >
4
3
2
1
1
2
3
4
< HRD-842 >
26_ connecting with other device
CONNECTING EXTERNAL DEVICES
M The following figures are based on Model HRD-1642.
Connecting the USB
1. By factory default, a USB port is provided for external connection.
2. You can connect a USB HDD, USB memory or mouse to the USB port.
3.
If a USB HDD is connected to the system, recognition and settings are available in “Main Menu >
Device
>
Storage Device”. (Page 57)
4. The product supports hot plugging function that enables connecting/disconnecting USB devices while in
operating the system.
J If the USB storage media for backup is not formatted by the product, format it as FAT32 file system with a PC.
To prevent from USB ports being damaged, please unplug USB devices before openning the front cover.
connecting with other device
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
CONSOLE HDMI eSATA
VGA OUT
SERIAL
12345678
9 10111213141516
123456 78 9 1011 121314 1516
ALARM IN
G G G G
NETWORK USB
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
15
1
6
G
A
U
DI
O
IN
C
H5
~ CH16
14
7
8
4
15
16
SO
LE
O
N
S
CO
HDMI
HDMI
HDM
HDMI
HDMI
DM
DM
DM
D
DM
DM
DMI
DMI
H
HDMI
HD
H
I
I
VG
A
OU
T
NETWOR
R
K
eSATA
eSATA
eSATA
S
S
SAT
SA
AT
T
TA
USB
USB
USB
USB
USB
S
S
1
2
3
4
ALARM OUT
+
RX
M
G
1
N
O
COM
COM
COM
COM
NC
NO
NO
N
O
2
3
4
+
-
1
9
EO
I
N
X
+
R
-
+
DE
AUDI
+
TX
IO
+
S
ERIAL
C
H1
CH3
C
H
2
C
H
4
AUDIO OUT
DIO O
IN
VI
9
3
4
4
4
4
4
4
4
4
4
4
5
6
11
12
13
10
2
AUDIO IN AUDIO IN
VIDEO IN SPOT VIDEO OUT (VGA) NETWORK AC 100-240V~IN
AUDIO OUT HDMI USB eSATA HDD
English _27
●CONNECTING WITH OTHER DEVICE
Connecting External SATA HDD (eSATA)
External SATA port is provided on the rear panel.
If connected to the system, the external SATA HDD (eSATA) can be recognized and configured in “Main Menu >
Device > Storage Device”.
J Use a cable shorter than 1 m for the external external SATA HDD (eSATA) connections.
Unexpected disconnection to a device in use which is connected via eSATA may restart the system. Check whether the
device is in use before disconnecting it.
Connecting POS Device
You can connect a POS device to the RS-232C port on the product’s rear side when you connect it directly
with a RS-232C cable.
Connection setup for the RS-232C port is available in “Main Menu > Device > POS Devices”, press the
<POS Device Setup> button and set <Baudrate, Parity, Data, Stop bit>. (Page
60
)
Connecting the Alarm Input/Output
M The following figures are based on Model HRD-1642.
The Alarm In/Out port at the back is composed of the following.
• ALARM IN 1 ~ 16 : Alarm Input Port
• ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm Input and
resumes sensing.
• ALARM OUT 1 ~ 4 : Alarm Output Port
ALARM OUT
(30VDC 2A,
125VAC 0.5A MAX)
ALARM IN
(5mA sink)
ALARM IN
(5mA sink)
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
CONSOLE HDMI eSATA
VGA OUT
SERIAL
12345678
9 10111213141516
12345678 9 1011 12131415 16
ALARM IN
G G G G
NETWORK USB
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
M
C
OM
2
3
4
ALARM OUT
G
A
LARM
R
E
S
E
T
1
2
3
4
5
ALAR
G
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
12 345678 9 1011 121314 1516
ALARM IN
G G G G
M
T
1
NO
CO
M
CO
M
CO
M
CO
M
NC
NO
N
O
N
O
2
3
3
4
4
ALARM OUT
G
+
-
TX
+
-
RX
ALAR
M
RE
S
E
T
G
1
2
3
4
5
6
7
8
9
1
0
11
1
2
1
3
14
1
51
6
ALARM
IN
G
G
G
Sensors Alarm
28_ connecting with other device
connecting with other device
Connecting the RS-485 Device
Connect the [TX/RX +, –] device through the back port.
M
You can connect and control the PTZ camera which supports the RS-485 communication.
Check if the RS-485 device is compatible with the product first.
Pay attention not to change the polarity (+/-) of the RS-485 device when connecting it.
Depending on camera’s type, connection polarity can be different.
For further information, refer to the respective PTZ Camera’s documentation.
CONNECTING THE NETWORK
M The following figures are based on Model HRD-1642.
Connecting to Network through Ethernet (10/100/1000BaseT)
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
CONSOLE HDMI eSATA
VGA OUT
SERIAL
12345678
9 101112 13141516
12345678 9 101112 131415 16
ALARM IN
G G G G
NETWORK USB
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
1
NO
COM
2
3
ALARM OUT
+
-
TX
+
-
RX
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
ALARM
RE
S
E
T
M
C
OM
NO
4
OUT
G
COM
3
O
1
N
O
COM
C
OM
C
N
C N
O
N
O
2
3
A
LARM
O
+
-
TX
+
-
R
X
PTZ camera
system keyboard
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
CONSOLE HDMI eSATA
VGA OUT
SERIAL
12345678
9 10111213141516
123456 78 9 1011 12131415 16
ALARM IN
G GG G
NETWORK USB
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
NETW
O
R
K
NETWORK
N
ETW
O
RK
NETWORK
Hub/Switcher
Hub/Switcher
Back Bone
Windows
Network Viewer
English _29
●CONNECTING WITH OTHER DEVICE
Connecting to the Network using the router
Connecting to Network through PPPoE
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
CONSOLE HDMI eS ATA
VGA OUT
SERIAL
12345678
9 101112 13141516
12345678 9 101112 13141516
ALARM IN
G G G G
NETWORK USB
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
NETW
O
RK
NETWORKNETW
O
R
K
NETWORK
Windows
Network Viewer
PPPoE MODEM
Hub/Switcher
Phone(PPPoE) Line
1
NO
COM COM COM COM
NC NO NO NO
234
ALARM OUT
G
+-
TX
+-
RX
ALARM
RESET
CH1
CH3
CH2
CH4
CONSOLE HDMI eS ATA
VGA OUT
SERIAL
12345678
9 10111213141516
12345678 9 101112 13141516
ALARM IN
G G G G
NETWORK USB
AUDIO IN CH5 ~ CH16
VIDEO IN
AUDIO OUT
AUDIO IN
NETWORK
NETWORKNETWOR
K
NETWORK
Broadband Router
xDSL or Cable Modem
External Remote PC
DDNS Server
(Data Center)
xDSL or Cable Modem
30_ live
live
GETTING STARTED
Starting the system
1. Connect power cable to the product’s rear.
2. Touch and hold the front power button for over 3 seconds.
M It takes about 10 seconds to display the start screen after
booting.
3. The boot up screen appears.
Booting up may take about 3 minute, as indicates
progress with icons.
If a new HDD is installed, the initialization process may
take longer.
4. The live screen appears with a beep.
Check Camera Signals Guide
This DVR product automatically recognizes camera signals.
Depending on the installation environment, the automatically
recognized signal may be different from the camera that is
actually connected.
If the image is not displayed after the installation, check the
signal type of the connected camera and set it manually.
live
OK
x This DVR product automatically recognizes camera signals.
x Depending on the installation environment,
the automatically recognized signal may be different from the camera that is actually connected.
x If the image is not displayed after the installation,
check the signal type of the connected camera and set it manually.
Check Camera Signals Guide
REC
REC
2015-01-01 01:10:25
English _31
●LIVE
Shutting Down the System
You can shut down the system only if you have logged in to the DVR.
You require permission to shut down the system if you are not logged in as admin.
1. Hold the <Power> button on the front for over 3 seconds,
or press Power button on the remote control once, or right
click to pop up shutdown menu and click Shutdown.
2. The “Shutdown” confirmation window appears.
3. Use the arrow keys on the remote control or the front
panel to move to <OK> and press the [ENTER] button or
click <OK>.
The system will shut down.
M
For the permission management, refer to “Permission
Management > Setting Permissions”. (Page 49)
Login
To access a DVR or restricted menu, you should have logged in to the DVR.
1. In live mode, right-click any area of the screen.
You will see the context sensitive menu as in the right
figure.
2. Click <Login>.
The login dialog appears.
You can also see the login dialog to access a desired
menu by pressing the [MENU] button on the remote
control or the front panel.
The login dialog will also appear if you press a menu button on the
remote control or the front panel of the DVR when the corresponding
menu requires logging in.
After logged in, press [RETURN] on the remote control to display the
logout dialog.
M For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 49)
2015-01-01 01:10:25
Scene Mode
Spot Out
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Login
2015-01-01 01:10:25
Shutdown
Are you sure to shutdown?
OK Cancel
2015-01-01 01:10:25
Login
x ID admin
x Password
OK Cancel
32_ live
live
J The default administrator ID is “admin”, and the password must be set when the user log in at the first time.
Set password for your wireless network if you use the product with a wireless router. Being not protected with password or
using the default wireless router password may expose your video data to potential threat.
To prevent from your personal information being exposed, please change your password every 3 months.
Note that the security and other related issues caused by careless management of password shall be be in the charge of the
user.
• To set your password, please click < > to check your password setup condition.
-If the password has 7 characters or less, the <Check the
password> screen pops up. After checking, please set
your password to one that is 8 characters or longer.
-Even if the password you enter is 8 characters or longer, if
it does not meet the specific conditions, the <Password
setting guide> screen pops up. After checking the
specific setup conditions, please set the password again.
Locking All Buttons
This will restrict access to all buttons available in the DVR.
1. In Live mode, press buttons in the order of [STOP (@)]
[FREEZE][STOP (@)][FREEZE][MENU].
<All Key Lock> confirmation window appears.
2. Select <OK>.
All keys are locked.
3. In the lock condition, press any button to display a dialog
where you are prompted to enter the password for
unlocking the buttons.
The button lock will be released if you enter the admin
password.
2015-01-01 01:10:25
All Key Lock
Are you sure to all key lock?
OK Cancel
For security, please set at least 8 characters in combination of alphabet and numbers.
If less than 10 digits, it must include special characters.
x ID admin
x New Password
x Confi rm P/W
Include Network Settings
Admin Group User Setup
Permission Management
Confi rm Password
OK
Please set up the password including alphabets,
Special characters and numbers at least 8 characters
OK Cancel
For security, please set at least 8 characters in combination of alphabet and numbers.
If less than 10 digits, it must include special characters.
x ID admin
x New Password
x Confi rm P/W
Include Network Settings
Admin Group User Setup
Permission Management
OK Cancel
Password setting guide
Set the password according to the below rules.
x 8~9 characters : Combination of alphabet, number and special character
x
10~16 characters : Combination of two or more of alphabets, numbers and special characters
x ID and Password cannot be the same.
x
4 or more contiguous or repeated string characters and key arrangement are not allowed.
(Example : abcde123456, aaaaa11111, qwerty!@#$)
OK
English _33
●LIVE
LIVE SCREEN CONFIGURATION
Icons on the Live Screen
You can check the status or operation of the DVR with the icons on the live screen.
Part Names Functions
Current Date, Time Displays the current time and date.
bLogin Information When you are logged in, the “LOG ON” icon will be displayed.
cScreen Mode
Displayed if the recording is in process.
To cancel the recording, right click to select Record Stop from the context menu.
Displayed if the zoom function is activated.
Displayed if you press the Freeze button.
Displayed in Auto Sequence mode where all channels are switched at the specific time
interval.
System
Operation
Displayed if there is a problem with the cooling fan.
Displayed if the HDD is full and the DVR has an insufficient space to record.
Displayed if no HDD is installed or the existing HDD should be replaced.
Displayed if the HDD needs a technical examination.
Displayed while the backup is in process or if the backup data is played.
Displayed if a new firmware is found from the network.
Video Input
Status
Displayed if no input is entered in the condition that the camera is set to <ON>.
Nothing will be displayed on the screen if the camera is set to <OFF>.
2015-01-01 01:10:25
b c
CAM 01
CAM 01
34_ live
live
Part Names Functions
Camera Name/ Channel Displays the camera name and the changed channel, if any.
Camera
Operation
Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.
Displays AUDIO ON/MUTE.
Not displayed in video mode if deactivated.
If the sensor is set to <ON>, the input signal will be displayed on the screen of the
connected channel.
Displayed if a motion detected in the condition that the motion detection is set to <ON>.
Appears when the Tampering Detection is set to <ON> and a tampering attempt is
detected.
Displays the current record mode from Record/Event/Schedule.
Error Information
• If the internal HDD is not connected, the “NO HDD”( ) message will appear; if there occurs a problem,
you will see the “HDD FAIL”( ) message in the top left corner. In this case, make sure you contact the
service center for assistance as this may cause a failure of recording, playback or backup.
• If the cooling fan does not work properly or has a problem, the <Fan Information> window will appear and
the fan error icon ( ) will be displayed on the top left corner. In this case, check to see if the internal fan
works.
As a fan error can shorten the product life, make sure you contact the service center for assistance.
M If you see the fan error icon or No HDD, HDD FAIL icons on the screen, contact the service center for more details.
Live Screen Menu
In addition to the buttons on the front panel or the remote control, you can access a desired menu by right-
clicking the mouse any area in live mode.
Right click opens the context menu which shows different menu items according to the situation, such as
logged in/out state, split screen mode, and various operational conditions.
M Menu items of Search, Record, Backup, Shutdown and PTZ can be deactivated, depending on the user permission.
< Single Mode Menu >
2015-01-01 01:10:25
Scene Mode
Spot Out
PTZ Control
Zoom In
Audio
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
2015-01-01 01:10:25
< Split Mode Menu >
Scene Mode
Spot Out
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
English _35
●LIVE
Split Mode Menu
The context sensitive menu in split mode differs, depending on the login/logout status.
Menu Functions
Scene Mode Refer to “Live Mode”. (Page 38)
bSpot Out Refer to “Spot Out”. (Page 41)
cAudio On/Off Refer to “Audio ON/OFF”. (Page 42)
Freeze Refer to “Freeze”. (Page 42)
Stop Alarm Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 43)
Record/Stop Starts/stops the standard recording.
Play Plays the search result (data). Refer to “Search & Play > Play”. (Page 91)
Search Refer to “Search & Play > Search”. (Page 88)
Backup Refer to “Main Menu > Setting the Backup”. (Page 70)
Main Menu Accesses the main menu. Refer to the Using the DVR section. (Page 44)
Shutdown Turns down the DVR.
Show/Hide Launcher Shows or hides the launcher. Refer to “Show / Hide the Launcher Menu”. (Page 37)
mLogin/Logout You can log in or out.
2015-01-01 01:10:25
Scene Mode
Spot Out
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
c
m
b
36_ live
live
Single Mode Menu
The single mode menu is available only in Single Mode.
The menu, which appears as <Screen Mode> on a single screen, appears as <Full Screen> after selecting
only one channel on a split screen.
Menu Functions
Full Screen Select and click a desired channel in Split mode to switch to the full screen of the selected
channel.
bPTZ Control Accesses the PTZ Control menu.
The PTZ menu is activated only in One-Channel Live mode. (Page 85)
cZoom In Enlarges the selected image. (Page 41)
2015-01-01 01:10:25
Full Screen
Spot Out
PTZ Control
Zoom In
Audio
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
b
c
< Menu after selecting one channel
on the split screen >
< Single Mode Menu >
2015-01-01 01:10:25
Scene Mode
Spot Out
PTZ Control
Zoom In
Audio
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
English _37
●LIVE
Show / Hide the Launcher Menu
The Launcher menu appears on the bottom of the live screen.
1. In Live mode, right-click to display the context menu and select <Show Launcher> or <Hide Launcher>.
If selected <Hide Launcher>, the launcher menu disappears on the bottom of the live screen.
2. If <Show Launcher> is selected, the launcher menu appears at the bottom of the screen.
If you click the launcher menu using the mouse, it directly goes into the menu.
M
If no input is entered for 10 seconds, the menu will disappear.
The Launcher menu can be accessed only by using the mouse.
Menu Functions
Date/Time
Displays the current time and date.
The indication of AM/PM is displayed if you set 12 hours for the time format in “System >
Date/Time/Language > Time”. (Page 44)
bScreen Mode Press this button to switch the screen mode in sequence.
The current mode is highlighted in white.
cMenu Expansion Button Click to display the hidden menu to the right.
Audio Turns ON/OFF the sound of the selected channel.
Zoom In/Out Enlarges the selected area. This is available only in Single Live mode.
PTZ Runs the PTZ Control launcher.
The PTZ control launcher will be active on the Live screen after you select a single channel.
Alarm Stops the alarm if it's activated.
Freeze Freezes the Live screen temporarily.
Play Enters Play mode if a file to play exist, and if not, enters Search mode.
Record Start/End recording the Live screen.
2015-01-01
01:10:25
c b
38_ live
live
LIVE MODE
D
isplay Live images from 16 channels in a total of 8 layout of split screens.
Switching the screen mode
To switch the split mode, select a screen mode in the launcher menu, or right-click to select a screen mode in
the context menu.
Press the [MODE] button on the front panel or the remote control to switch the mode in the sequence of the
launcher menu items.
HRD-442 only supports full screen, 4-split screen, and automatic switchover screen.
HRD-842 does not support 16-split screen.
Switching the split mode
Display 16 Live images in the sequence of Single, 4-split and 9-split modes.
Auto Sequence
M In Single mode, If you have set <SEQ-Dwell Time> in “Setting the Device > Camera”, Auto Sequence will be conducted
at the set interval. (Page 54)
In a split mode, If you have set <Multi CH SEQ Time> in “Setting the Device > Monitor”, Auto Sequence will be
conducted at the set interval. (Page 62)
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH1 CH2
CH3 CH4
CH6 CH7
CH3
CH2
CH4
CH1
CH5
16-split mode 9-split mode 4-split mode 7-split mode
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH10 CH11 CH12 CH13 CH14 CH15 CH16
CH12
CH1
CH13
CH9
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH1
CH2
CH1
13-split mode 16(A)-split mode PIP
Auto Sequence
16
1
Single mode
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
CH1
13-16
9-12
5-8
1-4
4-split mode
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
10-16
1-9
9-split mode
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
English _39
●LIVE
Manual Switching
Press the left/right button on the front panel or the remote control, or click the arrow <◄/►> key to move to
the next split mode.
• If pressing the right [►] button in 9-split mode :
9-split (CH 1~9) mode 9-split (CH 10~16) mode Auto Sequence
• If pressing the right [►] button in 4-split mode :
Channel (CH 1~4) Channel (CH 5~8) Channel (CH 9~12) Channel (CH 13~16) Auto Sequence
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
10-16
1-9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
13-16
9-12
5-8
1-4
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
40_ live
live
Channel Setting
You can display the channel in a desired area of a split screen.
1. Place the cursor over the camera name of each channel to display the <▼> key to the right on the screen.
2. Click a camera name to display a channel list where you can select a different channel.
3. Select a desired channel and click it.
The current channel will be switched to the selected one.
Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also
change the channel position.
Ex : if switching CH 1 to CH 7
Switching to Single Mode
When in split mode, select and double-click a desired channel to switch to its Single mode.
Press the number corresponding to a desired channel on the front panel or the remote control to switch to its
Single mode.
Refer to “Remote Control > Using the numeric buttons”. (Page 18)
Ex : If double-clicking CH 3 or pressing the number “3” on the remote control or the front panel.
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH3
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
English _41
●LIVE
SPOT OUT
The Spot Out monitoring is independent of the Live mode, which monitors a specific channel through the Spot Out port.
Selecting a Spot Out mode
If an event occurs such as sensor, motion or alarm from the Spot Out port in connection with a monitor, you
can select a output screen mode.
1. In Live mode, right-click any area on the screen.
The Live menu appears.
2. Click Spot Out.
The split screen appears according to the Spot Out source.
(Page 63)
Spot Out: It supports auto sequence and single mode by default, and
additionally supports 16-split, 9-split and 4-split modes if selected
<Multi Spot> out.
ZOOM
This is available only in Single Live mode. In Single mode, select a desired area and use the Zoom function to enlarge
the picture.
1. Select <Zoom In> in the right-click menu.
Press the [ZOOM] button on the front panel or the remote control, or simply click < > in the launcher
menu. The zoom box appears.
2. Use the direction keys, or drag and drop to specify an area to enlarge.
3. Press the [ENTER] button, or double-click the selected area to enlarge the picture.
In the enlarged image, use the direction buttons (◄ ►) on the remote control or the front panel to move the enlarged
area.
4. Press the [ZOOM] button on the front panel or the remote control to release the zoom.
M Magnification ratio varies depending on camera’s resolution. The higher the resolution, the greater the magnification.
Simply click < > in the launcher menu will zoom out the image.
2015-01-01 01:10:25
Auto Sequence
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
Scene Mode
Spot Out
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
2015-01-01 01:10:25
2015-01-01 01:10:25
2015-01-01 01:10:25
42_ live
live
AUDIO ON/OFF
You can turn the sound on/off corresponding to the channel in Live mode.
AUDIO ON/OFF in Single mode
Click the audio icon ( ) on the screen, or press the [AUDIO] button on the front panel or the remote control
to turn it on/off.
M Only the channel where <Audio> is set to <ON> in “Device > Camera” displays the audio icon ( ) in Live mode that
you can use to turn the sound on/off.
FREEZE
This is available only in Live mode, this pauses playing the Live image temporarily.
1.
Press the [FREEZE] button on the front panel or the remote control, or click <
> in the launcher menu.
The playback of the image is stopped temporarily.
Sound continues to play during the pause.
2. Press the [FREEZE] button again, or click < >.
This will release the freeze.
English _43
●LIVE
EVENT MONITORING
This will display the channel in sync with a specific event (Sensor/Motion/Video Loss/Tampering) if it occurs.
In “Monitor > Event Display”, set the event monitoring to ON/OFF and specify the event display time. (Page 62)
• If multiple events occur simultaneously, the screen will switch to a split mode.
-2~4 events : 4-split mode
-5~9 events : 9-split mode
-10~16 events : 16-split mode
• If the second event occurs within the set time of <Event Display>, the first event will last until the second
one is terminated. (Page 62)
Ex : If you set <Event Display> to 5 seconds, and only one event occurs in CH 1.
Ex : If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the first
event occurred in CH 1.
M Press the [ALARM] button to reset the alarm settings and to release the event mode.
If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will be
performed.
This will also apply to the Spot Out monitor.
J In case of continuous events such as motion detection, switching to another split mode display may not immediate if
concatenating events follow, even when you stopped alarm of the event.
CH1
Event occurrence 5 seconds
Stop alarm
CH1
CH1 CH2
Event occurrence 4 seconds 9 seconds
Stop alarm
44_ main menu
You can setup the system properties, devices, and options for recording, event, backup
and network.
SYSTEM SETUP
You can setup Date/Time/Language, Permission, System Properties and Log.
Date/Time/Language
You can check and setup the current Date/Time and time related properties, as well as the language used for
the interface on the screen.
Setting the Date/Time/Language
Set the Date/Time/Language
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control or on the front panel.
If not logged in, it prompts with login window.
Refer to “Login”. (Page 31)
2. Use the left/right buttons (◄ ►) to select the <System>.
System property setup menu is selected.
3. Use the up/down buttons () to select <Date/Time/
Language> and press the [ENTER] button.
4. Select <Date/Time/Language>.
A dialog to setup Date, Time and Language.
5. Use direction buttons (◄ ►) to select an item to set
and make your changes.
• Date : Sets the date that will appear on the screen.
You can select the date format.
• Time : Sets the time and its format that will appear on the
screen.
Select either one from <24 Hours, 12 Hours (AM/PM)>.
• Time Zone : Sets the time zone of your area based on the
Greenwich Mean Time (GMT).
GMT (Greenwich Mean Time) is standard World Time and the basis
of world time zone.
• Time Sync. : You can set the DVR’s current time
synchronized to a selected <Time Server> regularly if you select to use <Time Server>.
In this case, <Date/Time/Language> setup does not allow time adjustment.
main menu
System
Logout Return
Date/Time/Language
Permission Management
System Management
Log Information
Date/Time/Language
Date/Time/Language
Holiday
x Date 2015-01-01 YYYY-MM-DD
x Time 08:14:24 24 Hours
x Time Zone GMT
x Time Sync. Setup
x DST Dec First (Sun) 0 Dec First (Sun) 0
x Language English
OK Cancel
English _45
● MAIN MENU
- Time Server : Enter an IP or URL address of the time server.
- Last Sync Time : Displays the most recent synchronization
time from the selected time server.
- Activate as Server : Set to <Use> to allow the DVR to act
as a Time Server for other DVRs.
• DST : Set up Daylight Saving Time with its period to make
the time earlier than the GMT of its time zone by 1 hour
during the set period.
• Language : Select your language. Sets the language for the
interface.
English, French, German, Spanish, Italian, Chinese(Simplified),
Russian, Korean, Polish, Japanese, Dutch, Portuguese, Turkish, Czech, Danish, Swedish, Thai, Romanian,
Serbian, Croatian, Hungarian, Greek, Chinese (Traditional), Finnish and Norwegian are available.
6. When the Date/Time/Language setup is done, press <OK>.
M You can also use numeric buttons on the remote control or front panel to enter values for Date, Time and other numeric
fields.
Setting Holiday
You can set specific dates to Holidays according to your preferences.
Holidays are applied to <Recording Schedule> and <Alarm Schedule> too.
Using the mouse may help make setup easier.
1.
Use the up/down buttons (
) in <Date/Time/Language> window to select <Date/Time/Language>, and
press the [ENTER] button.
2. Select <Holiday>.
A calendar for Holiday setup appears.
3. Use the left/right < > buttons to select year or month,
and press the [ENTER] button.
4. Use direction buttons (◄ ►) to select a desired date,
and press the [ENTER] button.
You will see the “Setting Holiday” screen.
Ex : Select January 12th and check on <1/12> only to make every
January 12th a holiday. Check both on <1/12> and <Jan 2nd
Mon> to make every January 12th and 2nd Monday of January
holidays.
5. When the Holiday setup is done, press <OK>.
Using the Calendar
Using the mouse may help make setup easier.
Select year and month.
Select the left/right < > key on the left/right side of year/month and press [ENTER] button to adjust
by 1 year/month.
Use direction buttons to select a date and press [ENTER] button.
A date with recorded data to be searched will appear in yellow in the System Log, Event Log, Time Search and Event Search.
Date/Time/Language
Date/Time/Language
Holiday
x Date 2015 -01-01 YYYY-MM-DD
x Time 08:14:24 24 Hours
x Time Zone GMT+08:00
x Time Sync. Setup Not Used
x DST Dec First (Sun) 0H Dec First (Sun) 0H
x Language English
OK Cancel
Time Synchronization Setup
OK Cancel
x Synchronization Use
x Time Server 203.248.240.140
x Last Sync Time Fail
x Activate as Server Use
OK Cancel
Date/Time/Language
Date/Time/Language Holiday
2015 Jan
Sun Mon Tue Wed Thu Fri Sat
1 2 3
4 5 6 7 8 9 10
11 12 13 14 15 16 17
18 19 20 21 22 23 24
25 26 27 28 29 30 31
OK Cancel
Date/Time/Language
Date/Time/Language Holiday
2015 Jan
Sun Mon Tue Wed Thu Fri Sat
1 2 3
4 5 6 7 8 9 10
11 12 13 14 15 16 17
18 19 20 21 22 23 24
25 26 27 28 29 30 31
Setting Holiday
OK Cancel
1 / 12
Jan 2nd Mon
46_ main menu
main menu
Permission Management
You can set permissions of each user over the DVR's specific function and settings.
Setting the Administrator
You can set and change Administrator’s ID and password.
The administrator can use and set all menu items and functions.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Permission Management>, and press
[ENTER] button.
2. Select <Admin>.
A dialog for Admin ID and Password input appears.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the ID and password.
M
The default administrator ID is “admin”, and the password must
be set when the user log in at the first time.
To prevent from your personal information being exposed, please change your password every 3 months.
Note that the security and other related issues caused by careless management of password shall be be in the charge of the
user.
If you click < >, a simple guideline to setting the password is shown.
4. When the administrator setup is done, press <OK>.
Using Virtual Keyboard
For alphanumeric inputs, the virtual keyboard window
appears.
Use direction buttons (◄ ►) to move to a desired
character, and press the [ENTER] button.
In the upper text input box of the virtual keyboard, there
displays a list of candidate words containing the selected
character. OK Cancel
` 1 2 3 4 5 6 7 8 9 0 - =
q w e r t y u i o p [ ] \
Del
a s d f g h j k l ; ‘
Caps Lock
z x c v b n m , . /
Shift
Space Ctrl
Select a word from the list, or use the keyboard to enter the whole word.
If there are many of candidate words, use < , > buttons to move between them forward and backward.
Select <OK>.
Entered word is applied.
For upper case letters, use <Caps Lock> button.
For special characters, use <Shift> button.
Using the virtual keyboard is the same to a normal keyboard use in your region.
You can enter the ID with case-insensitive alphanumeric characters only.
For the password, use alphabets and special characters excluding < \ > and <">.
You can use number buttons on the remote control or front panel.
For security, please set at least 8 characters in combination of alphabet and numbers.
If less than 10 digits, it must include special characters.
x ID admin
x New Password ************
x Confi rm P/W ************
Permission Management
Admin Group
OK Cancel
User Setup
English _47
● MAIN MENU
Setting the Group
You can create user groups and setup permissions for those user groups.
You can register a user for each group in <User>.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Permission Management>, and press
[ENTER] button.
2. Select <Group>.
A window for <Add>, <Delete>, <Rename>, and
<Group Authority> setup appears.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Add, Delete, Rename : You can add, delete, rename a
group or modify the permissions given to the group.
The virtual keyboard appears when <Add> or <Rename> was selected.
- Add : When you first run the DVR with the admin account, only the admin account exists. Add has already
been deactivated. Select <Add> to display the virtual keyboard. Enter a group name. You can add up to
10 groups.
- Delete : Deletes a user group that is already registered. Selecting Delete will delete all user accounts
belonging to that group.
- Rename : Renames a group that is already registered. Select <Rename> to display the virtual keyboard.
For entering a group name, refer to “Using Virtual Keyboard”. (Page 46)
• Group Authority : Sets permissions to access menu items of each group.
Users of a group can access checked functions.
4. When the group setup is done, press <OK>.
To set the group authority
You can set the permissions of the group users to access the menu according to the channel.
1. Select a menu to which the group permission is assigned.
The menu where the group permission is assigned will be
displayed in the Live menu when a group user logs in.
• Live View : You can set the permission to access the Live
screen according to the channel.
• Search : You can set the permission to access the Search
menu according to the channel.
• Backup : You can set the permission to access the Backup
menu according to the channel.
• Menu : You can set menus accessible with a specific
permission.
Group users can access the permitted menus only.
Select a menu to display the Menu Permission screen.
• Bi-directional audio: You will be given permission to use
two-way audio features.
• Record Lock, PTZ, Remote Alarm Out, Shutdown : Select
an item so that the item will be added to the permissions.
2. Select <OK>.
Select and assign a group user so that the user can
access the specified menu.
Permission Management
Group
Admin
OK Cancel
User
Add Delete Rename
x Group ABC
Group Authority
Live View
Search
Backup
Menu
Record Lock PTZ Remote Alarm Out Shutdown
Setup
Setup
Setup
Setup
Setup
Menu Permission
OK Cancel
Date/Time/Language
Date/Time/Language Holiday
System Management
System Information
Log Information
System Log Event Log Backup Log
All
System Device Record Event Backup Network
Permission Management
Group
Admin
OK Cancel
User
Add Delete Rename
x Group
x Group Authority
Live View
Search
Backup
Menu
Bi-directional audio
Record Lock PTZ Remote Alarm Out Shutdown
Setup
Setup
Setup
Setup
Setup
Permission Management
Group
Admin
OK Cancel
User
Add Delete Rename
x Group ABC
x Group Authority
Live View
Search
Backup
Menu
Bi-directional audio
Record Lock PTZ Remote Alarm Out Shutdown
Setup
Setup
Setup
Setup
Setup
Channel Setup
OK Cancel
1 2 3 4
5 6 7 8
9 10 11 12
13 14 15 16
All
48_ main menu
main menu
To restrict the user permissions
If the admin restricts all permissions of an added group, the users belonging to that group can access only
the default minimum menus and can change the user’s own password only.
1. Start the DVR.
If all permissions are restricted, only the Login dialog
should appear.
2. Log in with a registered user ID.
3. Right-click any area on the screen.
If all permissions are restricted, only the accessible context
menus should appear.
To change the user password
If you log in with a user account that is restricted to access the menu, you can change your own password only.
1. Log in with your account.
2. Select <User Menu>.
The Permission Management setup screen appears.
3. Select <Permission Management>.
The Password setup dialog appears.
4. Enter a new password.
5. Select <OK>.
You change to the password will be applied.
Login
x ID abc
x Password
OK Cancel
2015-01-01 01:10:25
Scene Mode
Audio Off
Freeze
Stop Alarm
User Menu
Hide Launcher
Logout
For security, please set at least 8 characters in combination of alphabet and numbers.
If less than 10 digits, it must include special characters.
x ID USER
x New Password ************
x Confi rm P/W ************
Permission Management
User
OK Cancel
English _49
● MAIN MENU
Setting the User
You can add a user and edit information of a registered user.
Users can be added only if a group was created in <Group> menu.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Permission Management>, and press
[ENTER] button.
2. Select <User>.
A window for Add User appears.
3. Use direction buttons (◄ ►) to select <Add> from the
window.
A window for “Add User” appears.
4. You can configure the Network Viewer settings including
name, ID, viewer, Select Group and password.
Result of the user setup appears in the <User> window.
To change the user property, use “Edit User”.
The “Edit User” window appears when you select a
desired item to be changed in the <User> window.
• Viewer : If you select <Use>, you will be given access to the
Web Viewer and Network Viewer.
Refer to “Connecting Web Viewer”. (Page 94)
For more information about use of Network Viewer, refer to the
Network Viewer's user guide.
5. When the user setup is done, press <OK>.
Setting Permissions
You can set restricted access for all general users.
Items with restrictions will require logging in for use.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Permission Management>, and press
[ENTER] button.
2. Select <Setup>.
The Restricted Access, Restriction on Network Access,
Auto Log out, Manual Input of ID setup screen appear.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Restricted Access : All menu items allowed for a user can
be set with restricted access.
- Checked ( ) : Restricted
- Not checked ( ) : Accessible
If it is not checked ( ) in <Restricted Access>, any user can access the item no matter what the <Group Authority>
setting.
If it is checked ( ) in <Restricted Access>, a user can access the item only if the user has permission in <Group
Authority> setting.
• Restriction on Network Access : Restricts remote access from a <Restricted Access> network.
- All Network : Restricts all access instances via Network Viewer and Web Viewer.
- Web Viewer : Restricts access via the Web Viewer.
• Auto Log out : A user will be automatically logged out if there is no operation on DVR for over set period of
time.
Group Name ID Viewer Delete
Permission Management
User
Admin
OK Cancel
Setup
Add
Group
x Group All Group
Previous/Next Page
Group Name ID Viewer Delete
Permission Management
User
Admin
OK Cancel
Setup
Add
Group
x Group All Group
Previous/Next Page
Add User
OK Cancel
x Name
x ID
x Viewer Not Used
x Select Group ABC
x Password
x Confi rm P/W
Permission Management
Setup
Admin
OK Cancel
Group
x Restricted Access
Live View Backup Record Lock Search
PTZ Remote Alarm Out Shutdown All
x Auto Log out OFF
x Manual Input of ID ON OFF
x Touch Button Sound ON OFF
x Touch Button ON OFF
User
x Restriction on Network Access
All Network Web Viewer
50_ main menu
main menu
• Manual Input of ID : Prompts you to enter the user ID
manually for the login process.
- Checked ( ) : Encloses the registered user IDs with the
[] symbols.
Use the virtual keyboard to enter the user ID.
• Touch Button Sound : You can set whether to sound beep
on use of front touch buttons.
• Touch Button : You can set whether to use the front touch
buttons or not.
4. When the permission setup is done, press <OK>.
System Management
You can check the system version, update to a newer version, as well as data backup and initialization.
Checking the System Information
You can check the current system version, broadcasting system, MAC address. You can update the system.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <System Management>, and press [ENTER]
button.
2. Check the Software Version, Broadcast Format and MAC
Address.
• System Information : Shows the current system’s
information.
The values can not be changed by a user.
• S/W Upgrade : Updates the DVR’s software up to date.
• DVR Name : Assigned name will be displayed in Network
Viewer, when connected to the DVR.
x Software Version HRD-1642 vx.xxh_yymmddhhmmss
x Broadcast Format NTSC
x MAC Address 00:00:F0:54:FF:FF
System Management
System Information Settings
Previous
x System Information
Search
OK
x Device Network
x Version No S/W Data
x DVR Name DVR
x S/W Upgrade
Login
x ID *****
x Password
OK Cancel
English _51
● MAIN MENU
• Updating the Software
1. Connect a device storing the software to be updated. (It may take about 30 seconds to recognize the
device.)
Upgradeable devices include USB memory and network device.
To update the network, the current DVR should have been connected to the network.
Upgrade via the proxy server may not be enabled due to the restricted access.
2. Select <System Management> from <System> window.
3. Select <System Information>.
4. Press <Search> button to display updated image, then the <Search> button switches to <Upgrade>.
The <Upgrade> button will be activated only if the current <Software Version> of the <System Information> is same to
or older than that of <S/W Upgrade>.
5. Press <Upgrade> button to display confirmation popup
for upgrading.
Press <OK> in the “System Upgrade” window.
While updating, it shows the progress.
6. When the updating is done, it automatically restarts.
Do not turn the power off until it finishes restarting.
M If “Upgrade Failed” appears, retry from the step 4.
When you experience continued failure, consult the service
center for assistance.
When you perform S/W update remotely using Smart Viewer,
it may take a max of 3 minutes to complete the update since
Smart Viewer popped up a confirmation message. This is to
guarantee that the DVR set operates stably. For a faster update,
use the USB cable to connect to the DVR set.
x Software Version HRD-1642 vx.xxh_yymmddhhmmss
x Broadcast Format NTSC
x MAC Address 00:00:F0:54:FF:FF
System Management
System Information Settings
Previous
x System Information
Search
OK
x Device Network
x Version No S/W Data
x DVR Name DVR
x S/W Upgrade
System Upgrade
OK Cancel
Current Version vx.xxh_yymmddhhmmss
New Version vx.xxh_yymmddhhmmss
Do you want to upgrade?
x Software Version HRD-1642 vx.xxh_yymmddhhmmss
x Broadcast Format NTSC
x MAC Address 00:00:F0:54:FF:FF
System Management
System Information Settings
Previous
x System Information
Search
OK
x Device Network
x Version No S/W Data
x DVR Name DVR
x S/W Upgrade
S/W Upgrade
Software upgrading...
52_ main menu
main menu
Settings
You can copy and import the DVR settings by using a storage media.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <System Management>, and press [ENTER]
button.
2. Select <Settings>.
A window of storage device and load factory default
appears.
3. Use direction buttons (◄ ►) to move to a desired item,
and export or import settings data to a storage device.
• Storage Device : Shows the connected storage device.
• Export : All logs recorded in the DVR are exported to the
storage media.
• Import : Imports DVR settings from the storage device and applies to the DVR.
If <Include Network Settings> is checked, the network settings will be imported too.
After importing the configuration, please reboot DVR to take effect.
• Load Factory Default : If <Default> is selected, a
confirmation dialog for “Load Factory Default” prompts.
Press <OK> to initialize the system to the factory default.
• Power Off : When power is off, Alarm 1 is activated. After
checking the checkbox, if you push the <Apply> button, all
event alarms that were set by Alarm 1 output will be
released. After this, it is impossible to select Alarm 1 by
other Alarm outputs.
If that function is set, all checkboxes in all alarm setup screens
and the Alarm 1 out checkbox are deactivated to Off.
4. To move to the previous menu, press <Previous>.
x Storage Device 0 MB (Remained Capacity)
x DVRUSB 38010100
x USBDVR No data
Include Network Settings
Settings
System Information
Previous
x Load Factory Default
x Power Off No. 1 alarm output used when the power is off.
Default
Export
Import
System Management
Apply
x Storage Device 0 MB (Remained Capacity)
x DVRUSB 38010100
x USBDVR No data
Include Network Settings
Settings
System Information
Previous
x Load Factory Default
x Power Off No. 1 alarm output used when the power is off.
Default
Export
Import
System Management
Apply
Load Factory Default
OK Cancel
Sure to Default Setting?
Recording stops few second.
English _53
● MAIN MENU
Log Information
You can browse logs on the system and events.
System Log
System Log shows log and timestamp on every system start up, system shutdown, and changes on system
settings.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Log Information>, and press [ENTER] button.
2. Select <System Log>.
Refer to “Using the Calendar”. (Page 45)
Click on the calendar < > to display the calendar window.
• Type : When there are too many logs, you can display logs
of the desired format by selecting the type.
• Export : All logs recorded in the DVR are exported to the
storage media.
3. Use direction buttons (◄ ►) to move to a desired item, and press <Search>.
Event Log
Event log shows recorded events on alarms, motion detections and video loss.
It also shows the log and its timestamp.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Log Information>, and press [ENTER] button.
2. Select <Event Log>.
3. Use direction buttons (◄ ►) to move to a desired item,
and select it.
4. Set Search Day, Channel and Type and the press
<Search>.
Refer to “Using the Calendar”. (Page 45)
Click on the calendar < > to display the calendar window.
Backup Log
You can find out who backed up and the details (backup time, channel, device to use, file format, etc.).
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <System> window to
move to <Log Information>, and press [ENTER] button.
2. Select <Backup Log>.
3. Use direction buttons (◄ ►) to move to a desired item,
and select it.
4. Specify a search term and select <Search> in the right
corner.
Backup details for the search term will be listed.
No. Log List Date/Time
Log Information
System Log Event Log
First Page
Search Day 2015-01-01
Previous
Export
Previous/Next Page
Type View all
Search
Last Page
Backup Log
No. Log List Date/Time
7 Motion Detection [CH 7] 2015-01-01 00:02:18
6 Motion Detection [CH 6] 2015-01-01 00:02:18
5 Motion Detection [CH 5] 2015-01-01 00:02:18
4 Motion Detection [CH 4] 2015-01-01 00:02:18
3 Motion Detection [CH 3] 2015-01-01 00:02:18
2 Motion Detection [CH 2] 2015-01-01 00:02:18
1 Motion Detection [CH 1] 2015-01-01 00:02:18
Log Information
Event Log
System Log
First Page
Search Day 2015-01-01
Previous
Export
Previous/Next Page
CH All CHs Type View all
Search
Last Page
Backup Log
No. User Date/Time
Log Information
Backup Log
System Log
First Page
Search Day 2015-01-01 ~ 2015-01-02
Previous
Previous/Next Page
Search
Last Page
Event Log
Export
54_ main menu
main menu
SETTING THE DEVICE
You can setup Camera, Storage Device, Remote Device, POS Device and Monitor.
Camera
Setting the Camera
You can set Video, Audio, Channel Name and Dwell Time of a Camera.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control or front
panel.
2. Use the left/right button (◄ ►) to select <Device>.
Device setting menu is selected.
3. Use the up/down buttons () to move to <Camera>,
and press [ENTER] button.
4. Select <Camera>.
Displays settings window for Video, Audio, CH Name,
SEQ-Dwell Time, Type, Screen Setup and Privacy Region.
5. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Video
-<ON/OFF> : You can turn ON/OFF the selected channel’s
camera.
-<Covert1> : Shows information other than the video of
the selected channel.
For privacy protection, it does not display the video while the recording continues.
-<Covert2> : Shows nothing but an empty screen while the recording continues.
M If the channel is set to <Covert1> or <Covert2> mode, the channel’s sound is not hearable.
However, the channel’s sound is recorded if its Audio setting is set to <ON>, even the sound is not heard in Live mode.
• Audio
- If set to <ON>, you can turn the audio of the channel ON/OFF on the Live screen.
- If set to <OFF>, the channel’s audio is off on the Live screen and not recorded.
Audio output is available for only 1 channel.
• CH Name : Up to 15 characters including blanks are allowed.
Refer to “Using Virtual Keyboard”. (Page
46
)
The first character should not be empty.
Device
Logout Return
Camera
Storage Device
Remote Device
POS Device
Monitor
CH Video
Audio CH Name SEQ-Dwell Time
Type
1 ON
OFF
CAM 01 5 sec AHD
2 ON
OFF
CAM 02 5 sec AHD
3 ON
OFF
CAM 03 5 sec AHD
4 ON
OFF
CAM 04 5 sec AHD
5 ON
OFF
CAM 05 5 sec AHD
6 ON
OFF
CAM 06 5 sec AHD
7 ON
OFF
CAM 07 5 sec AHD
8 ON
OFF
CAM 08 5 sec AHD
Camera
Camera
Screen Setup Privacy Region
OK Cancel
PTZ
Previous/Next Page
Type
English _55
● MAIN MENU
• SEQ-Dwell Time : You can set the dwell time between channels for the Live screen and Spot Out.
If set to <OFF>, the channel is not listed in the Auto Sequence mode.
• Type : AHD/TVI/CVI/CVBS is displayed according to the camera connected in auto mode.
• Screen Setup : The video appeared on the screen may vary
depending on the channel’s camera, configure the DVR
display to your preferences.
Select a channel and adjust the
<
(Brightness)>,
<
(Contrast)>,
<
(Color)> and
<
(EQ)> of the
selected channel.
On setting the EQ level in manual way, it is recommended that
larger level will be adapted in long distance cable case, while
smaller one in short distance cable case. (EQ level : 1~5)
Press the <Init> to initialize settings back to the default.
• Privacy Region : You can specify a certain area of the camera video to be protected for your privacy.
6. When the camera setup is done, press <OK>.
To set the privacy zone
Select <Privacy Region>.
When “Privacy Region” window appears, select a
channel for detection and set the area of motion
detection.
• To set the area in “Privacy Region” window
In the “Privacy Region” window, select desired region
from < >.
• Privacy Region
You can specify up to 4 privacy zones for each channel,
which can be identified by the color.
1 Purple 2 Green 3 Blue 4 Yellow
• To set the area using <Individual> selection
Privacy Region
OK Cancel
Apply to All CH
CH1
Privacy Region1
Individual
In the “Privacy Region” window, you can select cells individually by using <Individual>.
When selected <Individual>, “Privacy Region” window disappears and you can select cells one by one.
When the motion area setup is done, Right-click to select <Menu> in the context menu or the [MENU]
button on the remote control to display the “Privacy Region” window again.
- Clear All : Selected cell is removed from the Privacy Region.
- Menu : After selecting individual motion areas, move to the “Privacy Region” window.
If selected <Apply to All CH>, selected motion area is applied to all channels.
When completing the privacy zone settings, click <OK>.
Clear All
Menu
Screen Setup
Init Apply to All CH
CH1
OK Cancel
48 53 53 3
56_ main menu
main menu
Setting the PTZ
To use Camera’s PTZ functions, ID and protocols of each camera and DVR should be matched.
For other settings, refer to the <Remote Device> settings. (Page 60)
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Camera>, and press [ENTER] button.
2. Select <PTZ>.
A window of PTZ settings appears.
3. Use direction buttons (◄ ►) to move to a desired item,
and select it.
• Port : Select a port control method for the camera that is
connected to a channel.
You have two choices : <RS-485> and <Coaxial>.
• ID : Set the ID of the connected camera of each channel.
You can easily setup by using the numeric buttons on the remote control or front panel.
• Protocol : Set the protocol of the connected camera of each channel.
M You can check the camera’s ID and protocol if you turn the camera off and on after connecting it to the DVR.
When camera is connected through coaxial port, DVR would recognize HD or SD camera automatically and apply proper
protocol.
For HD camera, ACP protocol is applied.
For SD camera, PELCO-C protocol is applied.
4. When the PTZ setup is done, press <OK>.
CH Port
ID Protocol
1 RS-485 0
> None
2 RS-485 1
> None
3 RS-485 2
> None
4 RS-485 3
> None
5 RS-485 4
> None
6 RS-485 5
> None
7 RS-485 6
> None
8 RS-485 7
> None
* Coaxial Auto : HD : ACP, SD : PELCO-C
Camera
PTZ
Camera
Previous/Next Page
OK Cancel
Type
English _57
● MAIN MENU
Setting the Camera Type
You can set the camera type by selecting it manually/automatically.
Using the mouse may help make setup easier.
1. Use the up/down buttons (▲▼) in <Device> window to
move to <Camera>, and press [ENTER] button.
2. Select <Type>.
A window of Camera type settings appears.
3. Use direction buttons (▲▼◄ ►) to move to a desired
item, and select it.
• Type : Set the type of the camera connected to each
channel. You can choose from CVI, TVI, AHD and CVBS.
• Resolution: Set the mode of the camera connected to each
channel. You can choose from 4M, 1080P and SD mode.
• Mode : Select Auto or Manual in Mode option. Mode set as Auto as default, When there is no image on the
screen from the connected camera, customer may manually set camera’s type and resolution to make it
appear.
• EQ Levels: 1, 2, 3, 4, 5
4. Select <Check EQ>,auto get the EQ levels of all channels and save.
5. When the Camera type setup is done, press <OK>.
Storage Device
You can check information on storage devices.
Confirming Devices
You can check storage devices and their free space, usage as well as status.
Devices available are HDD, and USB devices (Memory, HDD).
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Storage Device>, and press [ENTER] button.
2. Select <Device>.
• No. : Shows the assigned number of the internal HDD.
To see the detailed positioning of the HDD according to the
number, refer to <HDD Map>.
• Used/Total : Shows the used/total capacity of the storage
device.
Storage Device
Device Format
OK Cancel
HDD Alarm
HDD Map
Device No. Used/Total Usage Status/Management
HDD 1 3.92G/0.98T Internal Normal
CH Type Resolution Mode
EQ
1 AHD
SD
Auto 3
2 AHD
4M
Auto 3
3 AHD
4M
Auto 3
4 AHD
4M
Auto 3
5 AHD
4M
Auto 3
6 AHD
4M
Auto 3
7 AHD
4M
Auto 3
8 AHD
4M
Auto 3
Camera
PTZCamera
Previous/Next Page
OK Cancel
Type
Check EQ
58_ main menu
main menu
• Usage : Sets the storage device’s usage.
- USB memory is used only for backups.
External USB HDD, SATA HDD are used for extension and backup.
A maximum of 2TB for each port is supported for backup on a high capacity SATA HDD such as RAID equipment
(ex: SVS-5R), and a maximum of 4TB for extension purposes.
SVS-5R supports only RAID1 and RAID5.
If an eSATA HDD device is used for extended storage or backup purposes, disconnecting eSATA device may restart the
system.
For backup use, the device can be disconnected if it’s not in use.
• Status/Management : Shows the current status of the HDD, as in Normal/Check/Replace.
- Normal : Available to use
- Check : Available to use but recommended to replace
- Replace : Requires immediate replacement.
• HDD Map : Shows the internal HDD’s locations according to
assigned numbers.
Refer to this for servicing or additional HDD installation.
3. To move to the previous menu, press <OK>.
< HRD-1642 >
HDD Map
OK
< HRD-842 >
HDD Map
OK
< HRD-442 >
HDD Map
OK
English _59
● MAIN MENU
Formatting
You can format a storage device.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Storage Device>, and press [ENTER] button.
2. Select <Format>.
A window for selection of device for formatting appears.
3. Use direction buttons (◄ ►) to select a device to be
formatted.
4. Select <Format> on the bottom of the screen.
Press <OK> on the “Manage” confirmation window will
start formatting the selected device.
5. When the formatting is done, press <OK>.
HDD Alarm
You can set alarm settings for HDD defects such as Check Alarm Output Port, Replace Alarm Output Port,
and its duration.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Storage Device>, and press [ENTER] button.
2. Select <HDD Alarm>.
A window for setting HDD check and replace output ports
and their durations appears.
3. Use direction buttons (◄ ►) to move to the desired
item.
• Alarm
- Alarm signal will output through the alarm out port on the
rear side when selected <1>, <2>, <3>, and <4>.
- If <BEEP> was selected, a beep will sound.
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.
• Check Alarm Output Port : If HDD generates check alarm, the alarm signal will output to the specified alarm
output port.
• Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specified
alarm output port.
• Duration : Sets the alarm duration for the alarm signal and beep sound.
- Check Alarm, Replace Alarm signals will output through the selected alarm out ports (1, 2, 3, and 4).
- If <BEEP> was selected, a beep will sound.
- If <All> was selected, both beep sound and alarm signal through rear side ports will output.
Storage Device
Device
OK Cancel
HDD Alarm
Format
Device Select Used/Total Usage
HDD 1 3.92G/0.98T Internal
Format
Storage Device
Device
OK Cancel
HDD Alarm
Format
Device Select Used/Total Usage
HDD 1 3.92G/0.98T Internal
Format
Manage
Formatting deletes all recordings.
Proceed formatting?
Recording stops few second.
OK Cancel
Storage Device
Format
OK Cancel
Device HDD Alarm
x Check Alarm Output Port
x Duration OFF
1 2 3
4 BEEP All
x Replace Alarm Output Port
x Duration OFF
1 2 3
4 BEEP All
60_ main menu
main menu
M <Check> status means that the HDD is operating but it has problems that require technical examination.
() appears on the Live screen.
<Replace> status means that the HDD has defect and requires immediate replacement.
() appears on the Live screen.
If the installed HDD is not recognized properly, a confirmation popup will appear.
4. When the HDD Alarm setup is done, press <OK>.
Remote Devices
You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Remote Device>, and press [ENTER] button.
2. Use direction buttons (◄ ►) to move to the desired
item, and press [ENTER] button.
3. Set the values of each communication setup of the remote
device.
• Baudrate : Baud rate settings of the DVR, PTZ camera and
system keyboard should be matched for proper operations.
4. Make sure to match IDs of the DVR, System Keyboard
and Remote Control, and press <OK>.
M For changing the remote control’s ID, refer to “Changing the Remote Control ID”. (Page 18)
POS Devices
You can set properties of POS devices connected to the DVR.
A POS device connection requires channel, preset, and Port/Ethernet settings.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <POS Device>, and press [ENTER] button.
2. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• POS USE : When selected <POS USE>, DVR and POS will
be connected.
J
If you change settings for the device and press <OK> while the
<POS USE> is not checked, the changes for POS device will not
be saved.
M POS function is not available on HD (1080p) cameras, please connect DVR with SD camera only.
System Keyboard OFF ID 1
Remote Control ON ID 0
Baudrate Parity Data Stop Bit Transfer type
9600
None 8
1 Half Duplex
Remote Device
OK Cancel
POS USE
POS CH Preset
Port/Ethernet
1 None No preset None
2 None No preset None
3 None No preset None
4 None No preset None
5 None No preset None
6 None No preset None
7 None No preset None
8 None No preset None
POS Device
OK Cancel
Previous/Next Page
POS Device Setup
English _61
● MAIN MENU
• POS Device Setup : Sets the communication setups for the
POS device and DVR.
It is independent to the Remote Device setup.
• CH : Select the camera to be synchronized to the POS
device.
If selected a channel input field, “Sync Channel Setup” window
appears.
One POS device can be synchronized to up to 16 cameras
(channels), however one channel cannot be synchronized to
multiple POS devices.
Channels to be synchronized to a POS device should be set to
“Event” in “Main Menu > Record > Recording Schedule”.
(Page 64)
• Preset : Sets the name, start and end strings of the receipt
for the preset.
Preset name should be unique.
Use <Add> button to display “Add Preset” window, and set its
name, start string, and end string.
• Port/Ethernet : Sets the port number for the DVR and POS
device connection.
COM1 : For RS-232C connections
7001~7016 : For Ethernet connections
3. When the POS Device setup is done, press <OK>.
POS USE
POS CH Preset
Port/Ethernet
1 None No preset None
2 None No preset None
3 None No preset None
4 None No preset None
5 None No preset None
6 None No preset None
7 None No preset None
8 None No preset None
POS Device
OK Cancel
Previous/Next Page
POS Device Setup
POS Device Setup
OK Cancel
Baudrate Parity Data Stop bit
1200
None
7
1
POS USE
POS CH Preset
Port/Ethernet
1 None No preset None
2 None No preset None
3 None No preset None
4 None No preset None
5 None No preset None
6 None No preset None
7 None No preset None
8 None No preset None
POS Device
OK Cancel
Previous/Next Page
POS Device Setup
Preset Setup
OK Cancel
Add
No. Name Start End Input char. Set Del
Add Preset
OK Cancel
x Name
x Start Keyword
x End Keyword
POS USE
POS CH Preset
Port/Ethernet
1 None No preset None
2 None No preset None
3 None No preset None
4 None No preset None
5 None No preset None
6 None No preset None
7 None No preset None
8 None No preset None
POS Device
OK Cancel
Previous/Next Page
POS Device Setup
Sync Channel Setup
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
CH
OK Cancel
62_ main menu
main menu
Monitor
You can configure information to be displayed and its format for Spot Out monitor.
Setting the Monitor
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Monitor>, and press [ENTER] button.
2. Select <Monitor>.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Event Display : Sets the dwell time of the event channel
display on the monitor when an event occurs.
If selected <Continuous>, it displays the channel until you
press [ALARM] button to release it.
• Display : Displays only checked items on the monitor screen.
• Multi CH SEQ Time : Sets the interval between automatic display switching in 4-split and 9-split mode of
the Live screen.
• VGA/HDMI : Set your preferred screen resolution to <VGA> or <HDMI>.
• HDMI Resolution Auto Detection : If you set it to <ON>, then the HDMI screen resolution is automatically
detected.
If a HDMI monitor is not connected, the resolution is set to VGA/HDMI.
If <VGA> or <HDMI> is not supported by the monitor, it may not be able to display anything.
4. When the monitor setup is done, press <OK>.
Screen Setup
Some monitors many not display information (camera name, icon, time information, etc.) about the DVR,
depending on the condition. Then, you can change the display position of the data.
1. In the <Device> window, press the up/down () button to move to <Monitor> and press the [ENTER]
button.
2. Select the <Monitor> item.
3. Select <Display Position Setup> in the bottom.
You will move to the <Display Position Setup> window.
4. Use the four direction buttons or the number buttons on
the front panel or the remote control to adjust the data
position.
2015-01-01 01:10:25
Display Position Setup
OK Cancel
30 30
30
30
Monitor
Monitor Spot Out
x Event Display OFF
x Display Date Time CH Name Icon
x Multi CH SEQ Time 5 sec
x
VGA/HDMI
1920X1080
x
HDMI Resolution Auto Detection ON
Mode
OK Cancel
Display Position Setup
English _63
● MAIN MENU
Setting the Spot Out
You can set the DVR to output information / video apart from the monitor out.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Monitor>, and press [ENTER] button.
2. Select <Spot Out>.
The number of Spot Out terminals differs according to the model.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Spot Out : It supports auto sequence and single mode by
default, and additionally supports 16-split, 9-split and 4-split
modes if selected <Multi Spot> out.
• Set Mode : A window for “Set Spot Out” appears and you
can set the channel for it.
You can set the dwell time between the screen switching in
“Setting the Device > Camera > SEQ-Dwell Time”.
(Page 54)
• Event Display : Sets the duration for the Spot Out on an
event.
If selected <OFF>, an event will not output to the Spot Out.
M You can setup using the mouse right button in Live screen.
Refer to “Spot Out”. (Page 41)
If selected <Multi Spot> double frame function is deactivated.
4. When the Spot Out is done, press <OK>.
Setting the Screen Mode
You can configure the Live screen and Split Screens.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Device> window to
move to <Monitor>, and press [ENTER] button.
2. Select <Mode>.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Live Screen : Select split modes for the Live screen.
16-split, 9-split, and 4-split screens are included by default.
• Play Screen : Select split modes for the playback screen.
Only the 13-split screen is optional.
Black shows the playback while white shows the Live
screen.
4. When the screen mode setup is done, press <OK>.
Monitor
Spot Out
Monitor
x Spot Out Multi Spot
SEQ
x Event Display OFF
Mode
OK Cancel
Set Mode All
Monitor
Spot Out
Monitor
x Spot Out Multi Spot
SEQ
x Event Display OFF
Mode
OK Cancel
Set Mode
Set Mode
All
All
Set Spot Out
OK
1 2 3 4
5 6 7 8
9 10 11 12
13 14 15 16
Monitor
Mode
Monitor Spot Out
OK Cancel
Live Play
x Live Screen
x Play Screen
64_ main menu
main menu
SETTING THE RECORDING
You can setup scheduled recording, event recording and other recording related settings.
Recording Schedule
Make your reservation on a date and time to schedule the recording on specified time.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control or front
panel.
2. Use the left/right button (◄ ►) to select <Record>.
Record menu is selected.
3. Use the up/down buttons () to move to <Recording
Schedule>, and press [ENTER] button.
4. Select <Recording Schedule>.
A window of scheduled recording setup appears.
5. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Channel : Select a channel to set the recording schedule
time and date format.
• Recording type : Select each time cell, and then select a
type to start recording.
• Apply to All CH : If selected <Apply to All CH>, “Apply to
All CH” window appears.
Press <OK> to apply the setup to all channels.
6. When the recording schedule setup is done, press <OK>.
M
Event recording and scheduled recording starts about 3 seconds
prior to the event/schedule for guaranteed recording.
Record
Logout Return
Recording Schedule
Event Record Duration
REC Quality & Resolution
Record Option
All 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
Mon
Tue
Wed
Thu
Fri
Sat
Hol
No Recording Continuous
Event Both(Cont&Evnt)
Apply to All CH
OK Cancel
Recording Schedule
CH1
All 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
Mon
Tue
Wed
Thu
Fri
Sat
Hol
No Recording Continuous
Event Both(Cont&Evnt)
Apply to All CH
OK Cancel
Recording Schedule
CH1
Apply to All CH
OK Cancel
Apply recording schedule to all channels?
English _65
● MAIN MENU
Recording Color Tags
Color Part Names Functions
White No Recording No schedule / event recording
Orange Continuous Scheduled recording only
Blue Event Event recording only
Green Both(Cont&Evnt) Both scheduled / event recordings
Each press of a selected cell will cycle through <No Recording>-<Continuous>-<Event>-
<Both(Cont&Evnt)>.
Event Record Duration
You can set the beginning and ending point of a recording on an event.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Record> window to
move to <Event Record Duration>, and press [ENTER]
button.
2. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Pre Event : The recording of an event will start at a
pre-determined time prior to the actual occurrence of the event.
If it is set to 5 seconds, the recording begins from
5 seconds before the event.
• POST Event : The recording will continue for a
pre-determined time after the actual end of an event.
If it is set to 5 seconds, the recording ends in 5 seconds after an event.
3. When the event recording duration setup is done, press <OK>.
REC Quality / Resolution
You can set resolution, FPS, and quality of recordings by channel, and by recording type of standard / event.
For more information about the resolution, refer to the “Product Specification” section. (Page 126)
Setting Standard Recording Properties
You can set each channel’s resolution, quality and FPS for normal recordings.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Record> window to
move to <REC Quality & Resolution>, and press
[ENTER] button.
2. Select <Standard>.
3. When the recording setup is done, press <OK>.
Event Record Duration
OK Cancel
Previous/Next Page
CH Pre Event
POST Event
1 OFF 1 min
2 OFF 1 min
3 OFF 1 min
4 OFF 1 min
5 OFF 1 min
6 OFF 1 min
7 OFF 1 min
8 OFF 1 min
CH Resolution
Record Rate
Record Quality
Type
1 4M 15fps
Level4 SD
2 4M 15fps
Level4 SD
3 4M 15fps
Level4 SD
4 4M 15fps
Level4 SD
5 4M 15fps
Level4 SD
6 4M 15fps
Level4 SD
7 4M 15fps
Level4 SD
8 4M 15fps
Level4 SD
REC Quality & Resolution
Standard Event
Previous/Next Page
OK Cancel
66_ main menu
main menu
Setting Event Recording Properties
You can set each channel’s resolution, quality and FPS for event recordings.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Record> window to
move to <REC Quality & Resolution>, and press
[ENTER] button.
2. Select <Event>.
Event recording setup window appears.
3. Use direction buttons (◄ ►) to move to a desired item,
and select it.
• Resolution : Sets the resolution of the recorded screen.
• Record Rate : Image Per Second, means the frames
recorded per a second.
• Record Quality : Sets the recording quality.
4. When the Event recording setup is done, press <OK>.
M The estimated total remaining count means the total number of remaining recordings for both standard and event
recordings.
You cannot increase the remaining count if the current remaining count has reached zero or there is no available remaining
count from any other page. If this is the case, reduce the remaining count for the current page, or do so for the same
channel on any other page.
Record Option
You can set the recording to stop or overwrite when the HDD is full.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Record> window to
move to <Record Option>, and press [ENTER] button.
2. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Disk End Mode : If selected <Overwrite>, recording will
continue despite the HDD full while overwriting the oldest.
If selected <Stop>, the recording will stop when the HDD is
full.
• Disk End Beep : If selected <Stop>, the button is activated.
If you check it, the beep will sound on the disk full and the
recording stops.
• Auto Delete : If you check it, Record Period setup is activated.
If you specify the auto deletion period, the recording data before the period will be deleted automatically.
This option will be enabled only if Disk End Mode is set to <Overwrite>.
• HDD Free Space : Shows remaining free space available on the HDD.
• Recordable (days/hours) : Shows estimation of remaining days and hours for recording, based on the
remaining free space.
3. When the recording option setup is done, press <OK>.
Record Option
OK Cancel
x Disk End Mode Overwrite
Disk End Beep
x Auto Delete 180 day
x Record Status
x HDD Free Space : 986 GB / 989 GB
x Recordable (Date/Time) :
Auto Delete
OK Cancel
The recording information will be deleted.
Do you want to proceed?
CH Resolution
Record Rate
Record Quality
Type
1 4M 15fps
Level4 SD
2 4M 15fps
Level4 SD
3 4M 15fps
Level4 SD
4 4M 15fps
Level4 SD
5 4M 15fps
Level4 SD
6 4M 15fps
Level4 SD
7 4M 15fps
Level4 SD
8 4M 15fps
Level4 SD
REC Quality & Resolution
Standard Event
Previous/Next Page
OK Cancel
English _67
● MAIN MENU
SETTING THE EVENT
You can set recording options when sensor, motion, image loss detection or tampering event occurs.
Sensor Detection
You can set the sensor’s operating condition and connected camera, as well as alarm output and its duration.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control or front
panel.
2. Use the left/right button (◄ ►) to select <Event>.
Event setting menu is selected.
3. Use the up/down buttons () to move to <Sensor
Detection>, and press [ENTER] button.
A window of sensor detection setup appears.
4. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Sensor Operation : Sets the operation mode of sensors.
-<OFF> : Sensor does not operate.
-<N.O> : Sensor is opened.
If the sensor is closed, it generates alarm.
-<N.C> : Sensor is closed.
If the sensor is open by interruption, it generates alarm.
• Cam : Select a channel to be connected to the sensor.
If selected camera, “Cam Preset setup” window appears.
Select a channel and setup the preset.
Preset setup can be done in PTZ mode.
Refer to “Preset Setting”. (page 87)
• Alarm : Sets the alarm output method.
For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 59)
• Alarm Duration : Sets the duration of alarm signal and alarm
sound.
5. When the sensor detection setup is done, press <OK>.
Sensor Detection
OK Cancel
Previous/Next Page
Sensor
Sensor Operation
Cam
Alarm
Alarm Duration
1 OFF 1 None 10 sec
2 OFF 2 None 10 sec
3 OFF 3 None 10 sec
4 OFF 4 None 10 sec
5 OFF 5 None 10 sec
6 OFF 6 None 10 sec
7 OFF 7 None 10 sec
8 OFF 8 None 10 sec
Sensor Detection
OK Cancel
Previous/Next Page
Sensor
Sensor Operation
Cam
Alarm
Duration
1 OFF 1 None 10 sec
2 OFF 2 None 10 sec
3 OFF 3 None 10 sec
4 OFF 4 None 10 sec
5 OFF 5 None 10 sec
6 OFF 6 None 10 sec
7 OFF 7 None 10 sec
8 OFF 8 None 10 sec
Cam Preset setup
OK Cancel
CH
Preset
1 None
2 None
3 None
4 None
5 None
6 None
7 None
8 None
CH
Preset
9 None
10 None
11 None
12 None
13 None
14 None
15 None
16 None
Sensor Detection
OK Cancel
Previous/Next Page
Sensor
Sensor Operation
Cam
Alarm
Alarm Duration
1 OFF 1 None 10 sec
2 OFF 2 None 10 sec
3 OFF 3 None 10 sec
4 OFF 4 None 10 sec
5 OFF 5 None 10 sec
6 OFF 6 None 10 sec
7 OFF 7 None 10 sec
8 OFF 8 None 10 sec
Alarm Setup
OK Cancel
1 2 3
4 BEEP All
Event
Logout Return
Sensor Detection
Motion Detection
Video Loss Detection
Tampering Detection
Alarm Schedule
68_ main menu
main menu
Motion Detection
You can set target detection region and motion, as well as the alarm signal output.
When the motion detection region is set, it detects motion within the area.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Event> window to
move to <Motion Detection>, and press [ENTER] button.
A window of motion detection area setup appears.
2. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Mode : Sets whether to activate motion detection.
• Sensitivity : Sets the sensitivity level of the motion detection.
• Alarm : Sets the alarm output method.
For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 59)
• Alarm Duration : Sets the duration of alarm signal and alarm sound.
3. When the motion detection setup is done, press <OK>.
Setting the Motion Detection Area
Select <Motion Region>.
When “Motion Region” window appears, select a
channel for detection and set the area of motion
detection.
• To set the area in “Motion Region” window
In the “Motion Region” window, select desired region
from < >.
• To set the area using <Individual> selection
In the “Motion Region” window, you can select cells
individually by using <Individual>.
Motion Region
OK Cancel
Apply to All CH
CH1
Individual
When selected <Individual>, “Motion Region” window disappears and you can select cells one by one.
When the motion area setup is done, press the <Menu> on the screen or the [MENU] button on the
remote control or front panel to display the “Motion Region” window again.
- Select : Selected cell is set to be a part of motion detection area.
- Unselect : Selected cell is removed from the motion detection area.
- Inverse : Unselected cells are set to be the motion detection area.
- Menu : After selecting individual motion areas, move to the “Motion Region” window.
If selected <Apply to All CH>, selected motion area is applied to all channels.
When the motion detection setup is done, press <OK>.
Select
Unselect
Inverse
Menu
Motion Detection
OK Cancel
Previous/Next Page
CH Mode
Sensitivity
Alarm
Alarm Duration
1 OFF Level10 (High)
None 10 sec
2 OFF Level10 (High)
None 10 sec
3 OFF Level10 (High)
None 10 sec
4 OFF Level10 (High)
None 10 sec
5 OFF Level10 (High)
None 10 sec
6 OFF Level10 (High)
None 10 sec
7 OFF Level10 (High)
None 10 sec
8 OFF Level10 (High)
None 10 sec
Motion Region
English _69
● MAIN MENU
Video Loss Detection
You can set the alarm to be generated on a camera disconnection, which causes a video loss.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Event> window to
move to <Video Loss Detection>, and press [ENTER]
button.
A window of video loss detection area setup appears.
2. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Video Loss State : Sets whether to activate video loss
detection.
• Alarm : Sets the alarm output method.
For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 59)
• Alarm Duration : Sets the duration of alarm signal and alarm sound.
3. When the video loss detection setup is done, press <OK>.
Tampering Detection
You can set to detect tampering attempts and trigger events, such as sudden change of camera’s framing
direction, blocked lens and other overall change of scenes from the video.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Event> window to
move to <Tampering Detection>, and press [ENTER]
button.
Tampering detection settings screen appears.
2. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Mode : Set whether to use Tampering Detection or not.
• Sensitivity : Set the sensitivity level of tampering detection.
• Alarm : Set the alarm output method.
• Alarm Duration : Set the alarm signal output and its dwell time.
3. When the tampering detection setup is done, press <OK>.
M Since the tampering detection is designed and optimized to function in accordance with the user defined sensitivity level, it
may not render a significant difference in detection with varied sensitivity in general monitoring situations.
When the tampering detection mode is set <ON>, it is recommended that the pre event recording time of the corresponding
channel should be set to 10 seconds or longer.
Video Loss Detection
OK Cancel
Previous/Next Page
CH Video Loss State Alarm
Alarm Duration
1 OFF None 10 sec
2 OFF None 10 sec
3 OFF None 10 sec
4 OFF None 10 sec
5 OFF None 10 sec
6 OFF None 10 sec
7 OFF None 10 sec
8 OFF None 10 sec
Tampering Detection
OK Cancel
Previous/Next Page
CH Mode
Sensitivity
Alarm
Alarm Duration
1 OFF Medium
None 10 sec
2 OFF Medium
None 10 sec
3 OFF Medium
None 10 sec
4 OFF Medium
None 10 sec
5 OFF Medium
None 10 sec
6 OFF Medium
None 10 sec
7 OFF Medium
None 10 sec
8 OFF Medium
None 10 sec
70_ main menu
main menu
Alarm Schedule
You can set the conditions and operating hours for scheduled alarms.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Event> window to
move to <Alarm Schedule>, and press [ENTER] button.
2. Use direction buttons (◄►) to move to a desired item,
and set the value.
• Alarm : Sets the alarm output method.
For further information on alarm output, refer to “HDD Alarm >
Alarm”. (Page 59)
• ON : Marked in orange, and always generates alarm on
scheduled time.
• OFF : Marked in white, no alarm is generated even if an event occurs.
• Event Sync : Marked in Blue, generates alarm only when an event occurs.
• Apply to All Alarm : Applies the configured schedule to all
alarms.
M
When the alarm is generated on the scheduled time, you can
stop the alarm by canceling the schedule.
3. When the Alarm Schedule setup is done, press <OK>.
BACKUP
You can check the backup device and set the backup schedule by channel or by time.
The product only supports external HDD of USB memory. (Page 126)
Setting the Backup
You can backup the desired data to a connected device.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control or front
panel.
2. Use the left/right button (◄ ►) to select <Backup>.
Backup menu is selected. Backup
Logout Return
Backup
All 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
Mon
Tue
Wed
Thu
Fri
Sat
Hol
OFF ON Event Sync Apply to All Alarm
OK Cancel
Alarm Schedule
Alarm1
All 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Sun
Mon
Tue
Wed
Thu
Fri
Sat
Hol
OFF ON Event Sync Apply to All Alarm
OK Cancel
Alarm Schedule
Alarm1
Apply to All Alarm
OK Cancel
Apply the alarm scheduling to all?
English _71
● MAIN MENU
3. Press the [ENTER] button.
A backup window appears.
You can directly access it from the “Live screen menu”.
(Page 34)
4. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Backup Range : Sets the <Start> and <End> time for the
backup.
• Channel : Sets the channel to backup.
You can select multiple channels.
• Device : Select a backup device from the recognized devices.
• Type : Sets the backup data format.
- DVR : Saved data can be played back only by the DVR.
- AVI : Saves the CODEC information provided by the DVR with the recording data, and saved data can be
played back by using external viewers (such as Windows Media Player) on a PC.
If you need to install a codec in Windows, run the x264_dvr.exe file in the codec folder that is created when you back up an
AVI file.
- SEC : Saves data in the Hanwha Techwin’s proprietary format with built-in viewer, which supports
immediate playback on a PC.
• File Name : You can set the back file name.
Refer to “Using Virtual Keyboard”. (Page 46)
• Check capacity : Shows the size of the selected backup data, used and available capacity of the selected
backup device.
• Overlap : Shows a list of overlapping data on a same time according to the number of data.
It appears when one channel has multiple data on a certain time point due to changing of time or time zone
settings, etc.
Refer to time and time zone of “Setting the Date/Time/Language”. (Page 44)
5. When the backup setup is done, press <OK>.
If no available device is recognized for backup, <OK> button is not activated.
J The application may slow down during the backup.
You can switch to the menu screen during the backup in operation, but playback of data is not available.
The data can be played back on a Webviewer while the backup is in progress but audio does not function.
When a memory device is used for backup, it is not available to use the full capacity of the media since the system
consumes a part of its capacity.
If backup has failed, select “Device > Storage Device” and check the free space of the HDD and check also if the HDD is
properly connected.
M Pressing the <Exit> during the backup will return to the previous menu, while the backup progresses.
Backup :
Used :
Free :
Check capacity
OK Cancel
Backup
x Start 2015-01-01 00:01:06 x End 2015-01-01 08:25:45
x Overlap List0
x Device USB x Type SEC
x Folder /20150101/ x File Name 0001
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
All
Change
72_ main menu
main menu
NETWORK CONFIGURATION
It provides networked monitoring of Live screen from a remote place, and supports mail forwarding function with
events. You can configure the network environment which enables such functions.
Connection Mode
You can set the network connection route and protocol.
Setting the Connection
Sets the protocol and environment of the network.
Using the mouse may help make setup easier.
1. Press the [MENU] button on the remote control or front
panel.
2. Use the left/right button (◄ ►) to select <Network>.
Network menu is selected.
3. Use the up/down buttons () to move to <Connection
Mode>, and press [ENTER] button.
4. Select <Interface>.
A window of connection mode setup appears.
5. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• IP Type : Sets the network connection mode.
• Transfer Bandwidth : Sets the maximum data flow to be
transferred. (Upload speed)
Options will vary depending on the selected connection
mode.
- For <Static>, <DHCP> : Select one from 50 kbps ~
2Mbps, and Unlimited.
- For <PPPoE>, select one from 50 kbps ~ 600 kbps.
Connection Mode
Interface Port Alarm
x IP Type Static
x Transfer Bandwidth 2Mbps
OK Cancel
x IP Address 192.168.1.200
x Gateway 192.168.1.1
x Subnet Mask 255.255.255.0
x DNS Manual 168.126.63.1
Network
Logout Return
Connection Mode
DDNS
Live Transfer
Mailing Service
SNMP
English _73
● MAIN MENU
• IP Address, Gateway, Subnet Mask, and DNS
- For <Static> : You can directly input IP Address, Gateway,
Subnet Mask and DNS.
- For <DHCP> : IP Address, Gateway, and Subnet Mask
are set automatically.
- For <PPPoE> : IP Address, Gateway, and Subnet Mask
are set automatically.
• ID, Password : In case you selected PPPoE, provide the
“ID” and its “Password”.
M
DNS server for <DHCP> and <PPPoE> can be set by user only if you selected <Manual>.
6. When the connection setup is done, press <OK>.
Setting the Port
1. Use the up/down buttons () in <Network> window to
move to <Connection Mode>, and press [ENTER]
button.
2. Select <Port>.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Protocol Type : Select the protocol type between TCP and
UDP.
- TCP : If compared to UDP, TCP connection is more stable
but slow. Recommended for Internet connection.
- UDP : If compared to TCP, UDP connection is less stable but fast. Recommended for use in LAN
environment.
If selected UDP, selections of Device Port, UDP Port and Unicast/Multicast are activated.
If setting the connection mode to PPPoE, you cannot select UDP for the protocol type.
• Device Port : Initially, <4520~4524> is set. It increases / decreases by 5.
- TCP: It has better stability and lower speed when compared to UDP, and recommended for internet
environments.
• UDP Port : Initially, <8000~8160> is set. It increases / decreases by 160.
• Unicast/Multicast : Select one between UDP-Unicast and UDP-Multicast.
If selected Multicast, Multicast IP and TTL are activated.
- UDP- Unicast : Transfers data packet to an individual client.
- UDP-Multicast : Allows data communication to multiple clients causing no additional traffic to the network.
• Multicast IP Address : User can directly input.
• Multicast TTL : Select from 0 ~ 255. Initial value for the TTL is set to <5>.
• HTTP Port : Enter the port number for the Web Viewer. Initially, it is set to <80>.
• Secure Video Transmission : Send encrypted video.
If it is set to <ON>, network performance can be limited.
• Multi Browser Support : The Web Viewer can be used with a browser that supports the Silverlight.
The multi viewer can be used only if the HTTP port is set to 80, protocol type is TCP and device ports range
within 4505-4530.
This is for the Siliverlight’s security purposes.
4. When the protocol setup is done, press <OK>.
Connection Mode
Port
Interface Alarm
x Protocol Type TCP
x Device Port 4520 ~ 4524
x UDP Port 8000 ~ 8160
x Unicast/Multicast UDP-Unicast
x Multicast IP Address 224.126.63.1
x Multicast TTL 5
x HTTP Port 80
ySecure Video Transmission ON OFF
* Multi Browser Support:
Device Port 4505~4530, HTTP Port 80
OK Cancel
Connection Mode
Interface Port Alarm
x IP Type PPPoE
x Transfer Bandwidth 600kbps
OK Cancel
x IP Address 192.168.1.200
x Gateway 192.168.1.1
x Subnet Mask 255.255.255.0
x DNS Manual 168.126.63.1
x ID ID
x Password ************
74_ main menu
main menu
Notification
J In a multi-browser environment, the <HTTP Port> should be set to 80 (private port).
Select one between 4505 and 4530 for RTSP
• Network Overview
USB USB
Internet
Local PC
DVR 1
Router (External IP: 109.112.92.133,
Local IP: 192.168.1.1
Cable/ADSL
Modem
DVR 2
DDNS Server
(https://ddns.hanwha-security.com/)
System DVR 1 DVR 2
WEB RTSP WEB RTSP
IP 192.168.1.200 192.168.1.200 192.168.1.202 192.168.1.202
Protocol TCP TCP TCP TCP
Private Port 80 4520~4524 81 4525~4529
Public Port 80 4520~4524 81 4525~4529
Connection Mode
Interface Port Alarm
x IP Type Static
x Transfer Bandwidth 2Mbps
OK Cancel
x IP Address 192.168.1.200
x Gateway 192.168.1.1
x Subnet Mask 255.255.255.0
x DNS Manual 168.126.63.1
Connection Mode
Interface Port Alarm
x IP Type Static
x Transfer Bandwidth 2Mbps
OK Cancel
x IP Address 192.168.1.202
x Gateway 192.168.1.1
x Subnet Mask 255.255.255.0
x DNS Manual 168.126.63.1
Connection Mode
Port
Interface Alarm
x Protocol Type TCP
x Device Port 4520 ~ 4524
x UDP Port 8000 ~ 8160
x Unicast/Multicast UDP-Unicast
x Multicast IP Address 224.126.63.1
x Multicast TTL 5
x HTTP Port 80
ySecure Video Transmission ON OFF
* Multi Browser Support:
Device Port 4505~4530, HTTP Port 80
OK Cancel
Connection Mode
Port
Interface Alarm
x Protocol Type TCP
x Device Port 4525 ~ 4529
x UDP Port 8000 ~ 8160
x Unicast/Multicast UDP-Unicast
x Multicast IP Address 224.126.63.1
x Multicast TTL 5
x HTTP Port 81
ySecure Video Transmission ON OFF
* Multi Browser Support:
Device Port 4505~4530, HTTP Port 80
OK Cancel
English _75
● MAIN MENU
• 1st Set Port Forwarding Setting
Port Forwarding is 4520~4524
(4520, 4521, 4522, 4523, 4524)
HRD-1642
192. 168. 1. 200
TCP
4520
4520
Port Forwarding is 80
HRD-1642
192. 168. 1. 200
TCP
80
80
• 2nd Set Port Forwarding Setting
Port Forwarding is 4525~4529
(4525, 4526, 4527, 4528, 4529)
HRD-1642
192. 168. 1. 202
TCP
4525
4525
Port Forwarding is 81
HRD-1642
192. 168. 1. 202
TCP
81
81
76_ main menu
main menu
Connecting and Setting the Network
Networking may differ from the connection method, check your environment before setting the connection mode.
When no router is used
• Static mode
- Internet connection : Static PPPoE, leased line, and LAN environments allows connection between the DVR
and remote user.
- DVR Network Settings : Set the <Connection Mode> in
<Interface> menu of the connected DVR to <Static>.
Consult your network manager for IP Address, Gateway and
Subnet Mask.
• DHCP mode
- Internet connection : Connect the DVR directly to a cable
modem, DHCP PPPoE modem or FTTH network.
- DVR Network Settings : Set the <Connection Mode> in
<Interface> menu of the connected DVR to <DHCP>.
• PPPoE mode
- Internet connection : An PPPoE modem is directly connected to the DVR, where the PPPoE connection
requires user ID and password.
- DVR Network Settings : Set the <Connection Mode> in
<Interface> menu of the connected DVR to <PPPoE>.
<ID> and <Password> should be the same to the PPPoE user
information.
If you don’t know the ID and password, consult your PPPoE service
provider.
Connection Mode
Interface Port Alarm
x IP Type Static
x Transfer Bandwidth 2Mbps
OK Cancel
x IP Address 192.168.1.200
x Gateway 192.168.1.1
x Subnet Mask 255.255.255.0
x DNS Manual 168.126.63.1
Connection Mode
Interface Port Alarm
x IP Type PPPoE
x Transfer Bandwidth 600kbps
OK Cancel
x IP Address 192.168.1.200
x Gateway 192.168.1.1
x Subnet Mask 255.255.255.0
x DNS Manual 168.126.63.1
x ID ID
x Password ************
English _77
● MAIN MENU
When a router is used
J To avoid IP address conflict with the DVR's static IP, check followings :
• Setting the DVR with a static IP
- Internet connection : You can connect the DVR to a router which is connected to an ADSL/Cable modem
or a router in a Local Area Network (LAN) environment.
• Setting the DVR Network
1. Set the <Connection Mode> in <Interface> menu of the connected DVR to <Static>.
2. Check whether the set IP address is in the static IP range provided by the Broadband Router.
IP Address, Gateway, and Subnet Mask : Consult your network manager.
Check whether the set IP address is in the static IP range provided by the Broadband Router.
J If a DHCP server is configured with starting address (192.168.0.100) and end address (192.168.0.200), you should set
the IP address out of the configured DHCP range (192.168.0.2 ~ 192.168.0.99 and 192.168.0.201 ~ 192.168.0.254).
3. Check the Gateway address and subnet mask are equal to those set in the Broadband Router.
• Setting the DHCP IP Address of the Broadband Router
1. To access the Broadband Router’s configurations, open a web browser on the local PC that is connected
to the Broadband Router and enter the router’s address (ex : http://192.168.1.1).
2. At this stage, make the local PC's windows network configurations to the below example :
Ex) IP Address : 192.168.1.2
Subnet Mask : 255.255.255.0
Gateway : 192.168.1.1
- Once connected to the Broadband Router, it prompts with password. While entering nothing to the User
Name field, enter “admin” into the password field and press <OK> to access the router configurations.
- Access the router’s DHCP configuration menu and set its DHCP server activation, and provide the start and
end address.
Set the start address (192.168.0.100) and end address (192.168.0.200).
M Above steps may differ from the router devices depending on the manufacturer.
78_ main menu
main menu
• Setting Router’s Port Forwarding
1. Set the protocol to <TCP>.
2. External Port Range : Enter the TCP Port set in the
<Device Port> in <Port> menu of the connected DVR.
If more than one DVRs are connected to the router, the
TCP port can be different.
3. Internal PC IP Address : Enter the IP address set to the
<IP Address> in <Interface> menu of the connected
DVR.
4. Internal Port Range : Set the same to the “External Port
Range”.
M
Above steps may differ from the router devices depending on the manufacturer.
Port forwarding is required when you want to access the DVR connected to the router from outside of the router’s network.
Alarm setting
1. In the <Network> setting window, press the top down
(▲▼) button to move to the <Connection Mode> mode
and press the [ENTER] button.
2. Select the <Alarm> menu.
3. Press the top/down/left/right(▲▼◄►) button to toggle
settings and set up your preferences.
• Disconnect Alarm Output Port : Select a method for
outputting an alarm when network connection is terminated.
- If you select <1>, <2>, <3> or <4> the signal is outputted
from the alarm output terminal in the rear.
- If you select <BEEP>, the alarm sound will be played.
- If you select <ALL>, the alarm signal outputs and the warning sounds from the rear will be heard at the
same time.
• Duration : Select the duration of alarm signal outputs and warning sounds.
- It is outputted to the alarm output terminal selected in the connection cancellation alarm output port.
- If you select <BEEP>, the alarm sound will be played.
- If you select <ALL>, the alarms signal outputs and the warning sounds from the rear will be set at the
same time.
4. After finishing setting the alarms, select <OK>.
Connection Mode
Interface Port Alarm
x Disconnect Alarm Output Port
x Duration OFF
OK Cancel
1 2 3
4 BEEP All
Connection Mode
Port
Interface Alarm
x Protocol Type TCP
x Device Port 4520 ~ 4524
x UDP Port 8000 ~ 8160
x Unicast/Multicast UDP-Unicast
x Multicast IP Address 224.126.63.1
x Multicast TTL 5
x HTTP Port 80
ySecure Video Transmission ON OFF
* Multi Browser Support:
Device Port 4505~4530, HTTP Port 80
OK Cancel
English _79
● MAIN MENU
DDNS
You can set the DDNS site for a remote user’s network connection.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Network> window to
move to <DDNS>, and press [ENTER] button.
DDNS Setup screen appears.
2. Use the virtual keyboard to enter the <Product ID>.
Refer to “Using Virtual Keyboard”. (Page
46
)
If selected <OFF> input fields are deactivated.
If selected <iPOLiS>, the server name field is disabled.
• DDNS Site : Set whether to use DDNS or not, and select
the DDNS site if enabled.
• Server Name : Enter the server name of the selected DDNS site.
• Product ID : Enter the product ID which was registered to the DDNS site.
• Quick Connect : Appears if the <DDNS Site> is set to <hanwha-security.com>.
To use this feature, connect the DVR to a UPnP router and set to <Use>.
M If the quick connect setup has been cancelled while progressing, it is automatically set to <Not Used>.
3. When the DDNS setup is done, press <OK>.
OK Cancel
DDNS
x DDNS Site hanwha-security.com
x Server Name
ddns.hanwha-security.com
x Product ID
x Quick Connect Not Used Use
x DDNS Host Address https://ddns.hanwha-security.com/
80_ main menu
main menu
DDNS Setting
DDNS is a short form of Dynamic Domain Naming System.
DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters
(ex : www.google.com) to an IP address consisting of numbers (64.233.189.104).
DDNS (Dynamic DNS) is a service that registers a domain name and the floating IP address with the DDNS
server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP
system.
• Setting DDNS in the DVR
Set <Protocol Type> in the <Port> menu of the connected DVR to the following :
Ex) Protocol Type : TCP
Device Port : 4520~4524
DDNS Site : hanwha-security.com
• DDNS Settings of the Router
Select the corresponding menu for the network transfer protocol of the router.
• SETTING UP Hanwha Techwin DDNS
Go to Your PC
1. Open your browser and go to https://ddns.hanwha-security.com/ and click <LOGIN>.
2. You first need to create an account.
Click <SIGN UP>.
3. Follow the account registration instructions on the website.
4. After completing the account registration, login to your
account.
5. Add your DVR to your account. Click <Register
Product>.
6. Create a name(Product ID) for your DVR. Use 4 to 20
alphanumeric characters without spaces. Select
classification, model number of the DVR and click <Product
Registration>.
HRD-1642
hrd1642shop
English _81
● MAIN MENU
7. After registration, you should see your product in the list.
Go back to DVR
1. From network tab, click on <DDNS>.
2. Under DDNS Site, select <hanwha-security.com>.
3. Under Product ID, enter the product ID you created on the
Hanwha Techwin DDNS website.
Under Quick Connect, select <Use> and click <OK>.
M If the connection was not successful, your router may not be
supporting UPNP.
For more information on enabling UPNP on your router, please
see Router manual.
OK Cancel
DDNS
x DDNS Site hanwha-security.com
x Server Name
ddns.hanwha-security.com
x Product ID
x Quick Connect Not Used Use
x DDNS Host Address https://ddns.hanwha-security.com/
OK Cancel
DDNS
x DDNS Site hanwha-security.com
x Server Name
ddns.hanwha-security.com
x Product ID hrd1642shop
x Quick Connect Not Used Use
x DDNS Host Address https://ddns.hanwha-security.com/hrd1642shop
OK Cancel
DDNS
x DDNS Site hanwha-security.com
x Server Name
ddns.hanwha-security.com
x Product ID srd1673dhome
x Quick Connect Not Used Use
x DDNS Host Address http://www.samsungipolis.com/srd1673dhome
Connection
OK
Quick Connect Success
hrd1642shop HRD-1642
Network
Logout Return
Connection Mode
DDNS
Live Transfer
Mailing Service
SNMP
82_ main menu
main menu
Live Transfer
Sets the quality of the image that is transferred from the DVR to the network.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Network> window to
move to <Live Transfer>, and press [ENTER] button.
The Live Transfer window appears.
2. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Resolution: Shows the selected network profile’s resolution
setting.
• Quality: Shows the selected network profile’s image quality
setting.
3. When the live transfer is done, press <OK>.
Mailing Service
You can send an e-mail to a DVR-registered user at a specific time interval, or if an event occurs.
M If an event occurs with a channel where the camera’s video is set to <OFF> or the remaining recording count is set to
<OFF>, only the text notification will be sent to the applicable email address.
J If you set the interval of the e-mail notice too short, the e-mail server may consider it as spam that will not be transferred
normally.
SMTP Setting
Sets the SMTP mail server.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Network> window to
move to <Mailing Service>, and press [ENTER] button.
2. Select <SMTP>.
You will see the SMTP setting window.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• ServerType : Displays the connected server type.
• Server Address : Enter a server to connect to.
• Port : Sets the communication port.
• Use Authentication : Check this if the SMTP server uses user authentication.
The account input box will be activated.
• ID : Enter a user to use authentication when connecting to the SMTP server.
• Password : Enter the password of the SMTP server user.
Mailing Service
SMTP Event
OK Cancel
Use Authentication
Group Recipient
x ServerType SMTP mail Server
x Server Address
x Port 25
ID
Password
x Secure Transfer Never
x Sender Address ex. user@example.net
E-mail Test
Live Transfer
OK Cancel
Previous/Next Page
CH Resolution
Quality
1 CIF Low
2 CIF Low
3 CIF Low
4 CIF Low
5 CIF Low
6 CIF Low
7 CIF Low
8 CIF Low
English _83
● MAIN MENU
• Secure Transfer : Select one from <Never> and <TLS (if available)>.
• Sender Address : Use the virtual keyboard to enter the sender’s e-mail address.
Refer to “Using Virtual Keyboard”. (Page 46)
• E-mail Test : Conducts the test on the server settings.
4. When the SMTP setup is done, press <OK>.
Event Setting
You can set the interval and type of the event that will be sent to the user.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Network> window to
move to <Mailing Service>, and press [ENTER] button.
2. Select <Event>.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Event Interval : Set the event interval.
If a series of events occurs, the e-mail will be sent at the specified
interval, not on each event.
• The number of attached images for each event : Set the
number of images attached to the e-mail sent in case an event occurs.
Can attach 1 to 5.
• Use Event Transfer : Select an event type to send if an event occurs.
If the selected event occurs, the e-mail will be sent to the group that has the recipient authority.
4. When the event setup is done, press <OK>.
Group Setting
You can set the group to whom the e-mail is sent, and specify the permission for each group.
You can add recipients for each group in the <Recipient> menu item.
The recipient is set separately from the DVR user group.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Network> window to
move to <Mailing Service>, and press [ENTER] button.
2. Select <Group>.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Add : Select <Add> and use the virtual keyboard to add a
group.
Refer to “Using Virtual Keyboard”. (Page 46)
• Delete : Deletes the selected group.
• Rename : You can reset the recipient permission of an existing group.
• Recipient Permission : Set the permission of the recipient group.
4. When the group setup is done, press <OK>.
Mailing Service
Group
SMTP
OK Cancel
Recipient
x Group
x Recipient Permission
Sensor Motion Tampering
Change P/W HDD Info Video Loss
Power On/Off Manual Record
Event
Add Delete Rename
Mailing Service
SMTP
OK Cancel
Recipient
x Event Interval 10 min
x The number of attached images for each event 1
x Use Event Transfer
Sensor Motion Tampering
Change P/W HDD Info Video Loss
Power On/Off Manual Record
Event Group
84_ main menu
main menu
Recipient Setting
You can add/remove a recipient(s) to/from the specified group and edit the group if necessary.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Network> window to
move to <Mailing Service>, and press [ENTER] button.
2. Select <Recipient>.
3. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Add : You can select a recipient name, e-mail address or
group.
You should have created a group in the <Group> menu
item before you can add a user to the group.
For inputting the recipient name and email address, refer to
“Using Virtual Keyboard”. (Page 46)
4. When the recipient setup is done, press <OK>.
SNMP
You can configure the settings for the SNMP protocol.
Using the mouse may help make setup easier.
1. Use the up/down buttons () in <Network> window to
move to <SNMP>, and press [ENTER] button.
The SNMP setup screen appears.
2. Use direction buttons (◄ ►) to move to a desired item,
and set the value.
• Enable SNMP v1 : SNMP version 1 will be active.
• Enable SNMP v2 : SNMP version 2 will be active.
- Read Community : Read community where you can
access objects that support the SNMP protocols.
- Write Community : Write community where you can
access objects that support the SNMP protocols.
• Enable SNMP v3 : SNMP Ver.3 is used.
- Password : SNMP Ver.3 initial user password is set.
3. When the SNMP setup is done, press <OK>.
Mailing Service
SMTP
OK Cancel
Event Group Recipient
Group Name e-Mail Address Delete
Add
x Group All Group
Previous/Next Page
Mailing Service
SMTP
OK Cancel
Event Group Recipient
Group Name e-Mail Address Delete
Add
x Group ABC
Previous/Next Page
Add recipient
OK Cancel
x Name
x Email
x Select Group ABC
SNMP
OK Cancel
x Enable SNMP v1
x Enable SNMP v2
Read Community public
Write Community write
x Enable SNMP v3
Password
English _85
● MAIN MENU
CONTROLLING A PTZ DEVICE
The DVR enables you to adjust the settings of a PTZ camera as well as an ordinary one to your preference.
PTZ Device
The PTZ device can be activated only if a channel in connection with the PTZ camera is selected.
Getting started with PTZ
The PTZ camera is available, only if a channel is selected, in the following way :
Using the remote control buttons
Press the [PTZ] button on the remote control.
Using the launcher menu
Click < PTZ > to display the live launcher.
Using the right-click menu in Live mode
Right-click any area on the screen to display the context menu, and
select <PTZ Control>.
Using icons on the live screen
Click the < > icon on the live screen.
M
The PTZ function is available only if the PTZ camera is connected
so that the < > icon is displayed on the screen.
2015-01-01 01:10:25
2015-01-01 01:10:25
Scene Mode
Spot Out
PTZ Control
Zoom In
Audio
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
86_ main menu
main menu
Using the PTZ camera
You can use one camera to perform all functions of PAN, TILT and ZOOM for monitoring multiple places and
set the preset to your preference in a desired mode.
1. Launch the <PTZ Control> menu.
As the < > icon on the bottom right corner turns
yellow, you access the “PTZ Control” mode to display the
“PTZ Control” menu.
M
Be sure to configure PTZ working environments before operation,
since the PTZ Working(Active) mark can be appeared to be
activated even when PTZ is not operative.
2. Use the PTZ wheel in the launcher menu to adjust the
monitoring area, or use the direction buttons (◄ ►) on
the remote control to move the camera to a desired place.
• PTZ Wheel : Clicking a nearer point to the center will move in that direction slowly; clicking a farther point
from the center will move fast.
Keep clicking left to rotate the lens counter clockwise; keep clicking right to rotate the lens clockwise.
• Zoom ( ) : You can use the Zoom function of the PTZ camera.
• IRIS ( ) : Adjusts the intensity of radiation incoming to the iris.
• Focus ( ) : Enables you to adjust the focus manually.
• Swing : Moves between the preset start point and end point.
• Group : Moves in the path specified by combining the preset, pattern and auto pan.
• Trace : Moves camera’s framing in the predefined path.
• Preset : Sets the preset position for camera framing and moves to designated preset position when
selecting a desired preset.
• Tour : Moves in the path specified by combining multiple groups.
For the coaxial communications, the operation may differ depending on the protocol.
M Before entering the PTZ device control mode, set the values of the PTZ device in the <Setting the PTZ> menu.
(Page 56)
For camera specifications that supports PTZ comtrol depending on communication method, refer to our web site.
2015-01-01 01:10:25
PTZ Control CAM01
Select Preset
Save
Rename
Camera Setup
Exit
Swing
Select
Group
Select
Trace
Select
Preset
Select
Tour
Delete
Delete All
English _87
● MAIN MENU
Preset Setting
A preset is a set of specific target points of a PTZ camera, and up to 127 presets per a camera can be stored.
Using the mouse may help make setup easier.
1. In PTZ Control mode, use the direction buttons to adjust the camera in a desired direction.
2. Select the <Save> key.
The virtual keyboard for inputting the preset will appear.
Refer to “Using Virtual Keyboard”. (Page
46
)
• Save : You can add and save the preset.
• Rename : You can change the settings of the existing presets.
• Delete : Deletes the selected preset.
• Delete All : Deletes all existing presets.
M If you replace the camera of the channel that stores the preset list with a new one, you should reset the preset accordingly.
3. Press <OK>.
The preset will be saved as a name that you entered.
Camera Setting
A PTZ camera has its own menu system. Optimize the PTZ camera according to the DVR.
Using the mouse may help make setup easier.
• Select <Camera Setup> in the PTZ Control menu.
The camera-specific menu appears.
You can configure the settings of those cameras that support the
protocols of Samsung-E/Samsung-T/Pelco-D/Pelco-p/Panasonic/
Phillips/AD/DIAMOND/ERNA/KALATEL/VCL TP/VICON/ELMO/GE.
If you are setting Auto Pan or Pattern in the camera menu, press
and hold the appropriate button for a certain time so that the
button operation can be different from that in normal PTZ setting.
2015-01-01 01:10:25
Camera Setup
Exit
88_ search & play
SEARCH
You can perform the search for recorded data by the time or by the search criteria such as an event.
You can access the <Search> menu directly in Live mode.
1. In Live mode, right-click any area of the screen.
The Live menu appears.
2. Select <Search>.
Or, press the [SEARCH] button on the remote control or
the front panel.
3. The Search menu appears.
If you have not checked <POS USE> in the “Main Menu > Device
> POS Device” menu, the Search menu does not include the <POS
Search> item. (Page 60)
4. The search can be restricted by the Auto Delete function.
Refer to “Setting the Recording > Record Option”.
(Page 66)
M
Overlapped data : It only appears if there exists overlapped data
on a certain time, produced due to the change of DVR’s time
setup. The latest data comes first, from <List0>.
It does not appear in <Backup Search>.
Time Search
You can search for recorded data of a desired time.
As the time to display may be different depending on the time zone and the DST standard time, the time of
data recorded in the same time can be displayed differently depending on time zone and DST settings.
Using the mouse may help make setup easier.
1. Select <Time Search> in the <Search> menu.
2. Select a date to search.
Refer to “Using the Calendar”. (Page
45
)
3. The record data on the specific date will be listed.
The display bar is different according to the data type.
So check the data type for the color in the left pane.
4. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
• Go to First : Moves to the earliest date.
• Go to Last : Moves to the most recent date.
• Time : Enter a time to perform the search or use the up/down button <>> to select one.
• Previous/Next Page : Moves to the previous / next page. (Use the remote control or the buttons on the front
panel.)
search & play
Time Search
2015-01-01
Play Return
2015/01/01 00:01:17
Standard Schedule
Motion Sensor
V.Loss Etc
Tampering
Go to First Go to Last
Zoom In Zoom Out
All Data
CAM 01
CAM 02
CAM 03
CAM 04
CAM 05
CAM 06
CAM 07
Previous/Next Page
00:01
Overlapped Data List1
2015-01-01 01:10:25
Scene Mode
Spot Out
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
2015-01-01 01:10:25
Time Search
Event Search
Backup Search
POS Search
Motion Search
Return
English _89
● SEARCH & PLAY
• Zoom In : The map enlarges in detail.
It will switch in the sequence of 24 hours - 16 hours - 8 hours
- 4 hours.
• Zoom Out : The map will switch in the reverse order of the
detailed mode above.
It will switch in the sequence of 4 hours - 8 hours - 16 hours
- 24 hours.
M
Double-click a desired time to zoom it in/out.
• Preview : Click <Channel> and select (click, drag) a time in
<Duration> to display a still image for the portion.
- If the selected channel does not contain any recorded data, it will be marked black.
5. Select a data item and click <Play>.
The screen switches to the data playback mode.
Event Search
You can search for events by the channel and play them.
Using the mouse may help make setup easier.
1. Select <Event Search> in the <Search> menu.
2. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
All record events on a specific date will be found. (Normal/Schedule
recording included)
• Date/Time Preview : If you select a data item in the list, the
still image of the selected data will be displayed in the left
preview pane.
• Event : Displays the type of the event that occurred.
3. Select a data item and click <Play>.
The screen switches to the event data playback mode.
Backup Search
Searches for backup data in the connected backup device.
Only data in the format of DVR is included in the search.
Refer to <Type> in “Backup > Setting the Backup”. (Page 70)
Using the mouse may help make setup easier.
1. Select <Backup Search> in the <Search> menu.
2. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
• Record Period : Displays the record period.
• Channel info : Displays the recorded channel.
• Play Start Time : Select a time that you start playing.
3. Select a data item and click <Play>.
The screen switches to the backup data playback mode.
Backup Search
Play Return
No. Folder File Name
1 20150101 16190000
Previous/Next Page
x File Name x Channel info
x Record Period 2015-01-01 01:01:01 - 2015-01-01 01:01:10
x Play Start Time 2015-01-01 16:30:52
USB:USB2FlashStorage
Time Search
2015-01-01
Play Return
2015/01/01 00:01:17
Standard Schedule
Motion Sensor
V.Loss Etc
Tampering
Go to First Go to Last
Zoom In Zoom Out
All Data
CAM 01
CAM 02
CAM 03
CAM 04
CAM 05
CAM 06
CAM 07
Previous/Next Page
00:01
Overlapped Data List1
Event Search
CAM 01
2015-01-01 View all
Play Return
Previous/Next Page
2015/01/01 00:01:22
No. Date/Time Preview Event
3 02:47:54 ~ 02:48:59 Motion
2 00:39:06 ~ 00:40:30 Motion
1 00:01:22 ~ 00:02:28 Motion
Go to First Go to Last
Overlapped Data List1
90_ search & play
search & play
POS Search
You can search for data in the POS device that is connected to the DVR.
You can use the mouse to select the related items.
1. Select <POS Search> in the <Search> menu.
2. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
You can enter specific text to refine your search.
• Keyword : Use the virtual keyboard to enter a keyword.
• Search Criteria :
-<Case Sensitive> : If selected, search will be performed
case-sensitively.
-<Whole Word> : If selected, only the exact matches with
the keyword will be found.
• Preview : Select a data item in the list to display the preview image.
Information about the image will be displayed on the bottom of the screen.
•
: You can use these buttons to accelerate your search if you have a huge list of search results.
3. Select a data item and click <Play>.
The screen switches to the POS data playback mode.
Motion Search
If a motion is detected in each channel, you can set a desired area to perform the search.
You can use the mouse to select the related items.
1. Select <Motion Search> in the <Search> menu.
2. Use direction buttons (◄ ►) to set the search criteria
and press the [ENTER] button.
If you set the motion area to <Manual Area>, the <Setup> button
will be activated.
• Motion Region : Select an area to perform the search.
- All Area : Searches for all areas of the selected channel.
- Current Area : Searches for the motion area for each
channel specified in “Motion Detection >
Setting the Motion Detection Area”. (Page 68)
- Manual Area : You can set the motion area manually.
• Setup : The Setup button will be activated only if you have
set the motion area to Manual. Press this button to display
the area setting window.
• Date/Time : The Date/Time will be automatically set by the
hour, and the end time will be automatically set to one hour
later than the start time if it is set.
• Preview : Select a data item in the list to display the still
image of the item.
3. Select a data item and click <Play>.
The screen switches to the motion data playback mode.
Motion Region
OK Cancel
Apply to All CH
CH1
Individual
Motion Search
Date/Time 2015-01-01 03:41:18 2015-01-01 05:11:44
Play Return
No. Start Time
7 01:01:30
6 01:01:25
5 01:01:20
4 01:01:15
3 01:01:10
2 01:01:05
1 01:01:01
Previous/Next Page
Search
Channel CAM 01 Motion Region All Area Setup
2015/01/01 01:01:30
Go to First Go to LastOverlapped Data List1
POS Search
Date/Time 2015-01-01 02:41:18 2015-01-01 03:41:18
Play Return
POS CH Start Date/Time Keyword
1 1 2015-01-01 03:41:15 CHANGE _
1 1 2015-01-01 03:41:15 CASH _
1 1 2015-01-01 03:41:10 CASH _
Previous/Next Page
Search
Keyword Case Sensitive Whole Word
Go to First Go to Last
CHANGE
5.95
2015/01/01 03:41:15
Overlapped Data List1
English _91
● SEARCH & PLAY
PLAYBACK
Play
You can play data stored in the HDD and backup a desired portion of the data.
Using the mouse may help make setup easier.
1. In Live mode, click <Play> in the right-click menu or
< > in the launcher menu, or press the Play button on
the remote control or the front panel.
2. Use the up/down button () to select a menu.
For data search, refer to <Search>. (Page 88)
3. Select a data item and click <Play> in the Search menu.
The selected data is played and the play launcher appears
on the screen.
If there is an existing data, <Play> will start immediately without
performing the search.
• Playback Information : Displays the date and time of the
current data in the top corner.
• Backup : Click < > to set the current time to the start
time of backup; you can specify a backup area using the
mouse (yellow triangle).
Click < > again to set the current time to the end time of
the backup and the “Backup Range” window appears.
- Type : Supports formats of DVR, AVI and SEC.
Refer to a list of formats in “Setting the Backup”.
(Page 70)
- Device : Select a backup device.
- Check Capacity : Enables you to check the capacity of
the selected storage device.
4. If you want to return to the Live screen in Play mode, click <
> in the launcher menu or press the
[] button on the remote control or the front panel.
2015-01-01 01:10:25
Scene Mode
Spot Out
Audio Off
Freeze
Stop Alarm
Record
Play
Search
Backup
Main Menu
Shutdown
Hide Launcher
Logout
2015-01-01 01:10:25
REC
OK Cancel
Backup Range
x Start 2015-01-01 00:01:06 x End 2015-01-01 01:10:25
x Device USB x Type SEC
x Folder /20150101/ x File Name 0001
Backup :
Used :
Free :
Change
Check capacity
92_ search & play
search & play
Using the Playback Button
Part Names Functions
Play Timeline Indicates the current playback point, and can be used to move.
bSkip Backward Moves backward by unit time. (Move by 10 minutes)
cBackward Fast
Play Used for quick backward playback. (2 - 64x speed)
Backward Slow
Play Used for backward frame-by-frame search while in PAUSE. (1/2 - 1/8x speed)
Step Backward Moves backward by one frame at a time.
Pause Stops playing the current video temporarily.
Stop Stops playback and moves to the live screen.
Step Forward Moves forward by one frame at a time.
Forward Slow
Play
Ensured to play forward up to 4 channels simultaneously at a low speed. (1/2 - 1/8x speed)
In a split mode, the real time playback may not be supported, depending on the record quality,
resolution and number of channels. And some frame rates may be supported.
Forward Fast Play Used for quick forward playback. (2 - 64x speed)
Skip Forward Moves forward by unit time. (Move by 10 minutes)
Return Return to the search setup screen.
mAudio Sets Audio ON/OFF.
nZoom In / Out Zoom In or Out the current video for the selected channel.
REC Records all channels in Live mode.
Partial Backup Begins backup of the selected section of the video being played, with the specified starting/ending
point.
qMode Switch
Click a desired playback mode or press [MODE] to switch the screen mode in sequence.
The grey area in the center of the 13-split mode plays the Live channel.
The default channel of the Live mode is CH1, which can be changed later.
REC
q
English _93
● WEB VIEWER
INTRODUCING WEB VIEWER
What is Web Viewer?
Web Viewer allows remote access to your DVRs. You have
access to live video, archived video, PTZ control
(if configured), etc.
Product Features
• Remote access from a standard browser
• Supports PTZ camera controls
• Supports 1, 4, 9, 16 camera viewing formats (maximum of
16 cameras in the list).
• Gets jpeg, bmp or png format images to print and save to “Print or Save jpeg, bmp or png format images”.
• Record video in AVI format-compatible with popular media players. (needed the H.264 codec)
System Requirements
The following lists the recommended suggest hardware and operating system requirements needed to run
the Web Viewer.
OS
Windows XP SP3 or higher
Windows Vista
Windows 7
Mac OS 10.6 and later versions
Web Browser
-Windows OS : Internet Explorer 8, 9, 10, Firefox 3.6 or higher, Chrome 12 or
higher
-Mac OS : Safari 5 or higher, Firefox 3.6 or higher.
CPU Intel Core i7 3.4Ghz
Memory 4 GB or more
Graphic Card If user wants to support 1080p 16 channel display, in order to guarantee pictures'
display effect, it's recommended to use R9 270 4GB or higher Graphic Card.
HDD
50 MB (Installation space required)
* Additional HDD space required for recording.
Recorded file size will vary depending on recording quality settings.
web viewer
G
Network
94_ web viewer
web viewer
CONNECTING WEB VIEWER (Windows)
1. Open your web browser and type the IP address or URL of
DVR into the URL address box.
M
“192.168.1.200” is set to IP by default.
Set to an available IP address in IP Installer or "Network >
Connection Mode”.
The URL connection will be enabled only when the DDNS connection settings have been completed.
2. A user with the admin permissions should provide the
admin ID and password. A registered user should provide
the user ID and password.
J The default administrator ID is “admin”, and the password must
be set when the user log in at the first time.
Set password for your wireless network if you use the product with a wireless router. Being not protected with password or
using the default wireless router password may expose your video data to potential threat.
To prevent from your personal information being exposed, please change your password every 3 months. Note that the
security and other related issues caused by careless management of password shall be be in the charge of the user.
If there are more than one LAN cards for the PC, you can use a LAN card with a smaller interface matrix value in order to
receive video.
M
It allows up to 10 simultaneous access including the Admin and general users.
It does not allow multiple login of the Admin user.
Password of the Admin and general users can be changed in <Permission Management> menu of the DVR.
Normal users should have set <Viewer> under <Permission Management> to “Use” before connecting to the
Web Viewer. (Page 49)
All settings are applied by the DVR’s settings.
If you change such as the permission settings with logged in to the Web Viewer, you may go back to the log in
screen.
3. Click <Install ActiveX Control...>.
4. When the installation confirm message appear, click [Yes]
button.
All windows will be closed(IE).
English _95
● WEB VIEWER
5. When a program installation wizard window appears, press
the [Install] button to install the program.
6. When the program is installed, open the web viewer again
to login.
Live Viewer's main screen appears when you log in
successfully after installing the program.
96_ web viewer
web viewer
USING LIVE VIEWER (Windows)
The Live Viewer screen consists of following :
Menu Functions
Menu Selection Switches into corresponding menu screen by clicking each menu.
b
Address, Name, Time Displays the IP, model name, time, etc. of connected DVR.
c
DVR Time, PC Time Select <DVR Time> or <PC Time> for the OSD time information display setting of the Live Viewer.
Split Mode Selection Selects the type of split screen and specify the channel displayed in Display Pane.
Change Channel Switches into previous/next channel or perform Auto Sequence.
Click Auto Sequence button to display the Time Interval Selection menu.
CAPTURE Saves current video for selected channel in designated path.
PRINT Prints current video image for selected channel through designated printer.
AVI Save Records the live video in AVI file format in designated path, and then stops recording.
Recording status icon is displayed on screen during recording.
Audio Sets the sound connected to each channel to ON/OFF.
OSD Select the format of OSD information that will be displayed.
b
c
English _97
● WEB VIEWER
Menu Functions
PTZ Controls connect PTZ camera(s).
OSD Menu Goes to the relevant menu screen of a camera, which supports OSD menu and changes
the menu.
Display Pane Displays the video of camera connected to DVR.
Logout Click Logout icon for logout.
User ID Displays the user's ID.
M
Dual Stream selection : If you right-click a channel among the web viewer live screens, a dropdown menu, 'network
stream/record stream' is shown. The default setting is 'network stream'. In this setting, videos are displayed in
'network stream' resolution. If 'record stream' is selected, videos are displayed in 'record stream' resolution.
OSD Information Display
The channel number of the connected DVR are displayed.
b Either the <DVR Time> or the <PC Time> will be displayed as the
current date and time, according to your configuration.
c It displays whether the PTZ controls are active.
Shows Audio On/Off status.
Alarm icon appears when alarm is issued.
It disappears when pressed the [ALARM] button of the DVR.
Motion icon appears when a motion is detected.
Tampering icon appears when a tampering is detected.
Shows the recording status.
M
If you have set PTZ cameras for the DVR, “PTZ” is displayed on the
screen. Select a PTZ camera channel and use the [PTZ] button for
camera control.
Connected DVR
This displays the IP address and the status of the connecting
DVR.
M
Connection failure message
No Response : Appears when the DVR does not respond.
Access Denied : Appears when the maximum number of
users is exceeded.
The number of simultaneous connections are limited to 10.
Setting the Display of the OSD Time Information
Select <DVR Time> or <PC Time> for the OSD time
information display setting.
• DVR Time : Based on the time of the connected DVR
• PC Time : Based on the time of the PC currently running
the Web Viewer.
b
c
98_ web viewer
web viewer
Split-Screen
Click split mode selection button to switch to the
corresponding screen mode.
To switch to full screen mode
Click <
>.
Current split screen appears in full screen.
Press the [ESC] key to exit the full screen mode.
SIXTEEN MODENINE MODESINGLE MODE
SINGLE MODE
QUAD MODE
QUAD MODE
English _99
● WEB VIEWER
Changing the Live Screen Mode
16-split mode does not support “Sequence”, “Previous” and
“Next”.
• : When this button is clicked, the previous screen
appears.
- In SINGLE MODE, the channel numbers are switched in
reverse order.
- In QUAD MODE, the screens are changed like 1st 4 channels (1~4) 2nd 4 channels (5~8)
3rd 4 channels (9~12) 4th 4 channels (13~16).
- In NINE MODE, the screens are changed from 9 channels (1~9) to 7 channels (10~16).
• : When this button is clicked, the next screen appears.
- In SINGLE MODE, the channel numbers are sequentially switched from 1 to 16.
- In QUAD MODE, the screens are changed like 1st 4 channels (1~4) 2nd 4 channels (5~8)
3rd 4 channels (9~12) 4th 4 channels (13~16).
- In NINE MODE, the screens are changed from 9 channels (1~9) to 7 channels (10~16).
•
: When this button is clicked, screens are switched at a
preset interval.
- In SINGLE MODE, the channel numbers are sequentially
switched from 1 to 16.
- In QUAD MODE, the screens are changed like
1st 4 channels (1~4) 2nd 4 channels (5~8)
3rd 4 channels (9~12) 4th 4 channels (13~16).
- In NINE MODE, the screens are changed from 9 channels (1~9) to 7 channels (10~16).
Default setting time (10 seconds)
To capture a screen
1. Click <
> button.
When a pop-up window appears, select the saving path
for captured image.
2. Select the path and name the file. And then click the
<Save> button.
3. Save current camera’s video image as .bmp, .jpg or .webp
file.
J
If the browser does not operate in admin mode for Windows
vista/7, when you save the capture file, there can be problems in saving it as bmp, jpg or png.
100_ web viewer
web viewer
To print a screen
1. Click < > button.
2. Print current camera’s video image with the printer
connected to the PC operating the Web Viewer.
To save as AVI
1. Click <
> button.
When “AVI Setup” window appears, select the record
saving path and capacity.
2. Select a desired path, enter the maximum recording
capacity, and then click <OK> button.
Save current channel’s video as AVI file. For playing a video clip,
you can use the free video player to play the video.
(ex: GOM Player, KM Player, etc.)
After saving an AVI file, install the CODEC when playing it in Windows Media Player.
However, the video may not played properly, depending on the CODEC compliance of the player.
At least 1GB of free space is required for recording.
J
While recording current data in Web Viewer, you cannot select Split Mode buttons, switch to the previous/next
screen, or activate Auto Sequence function.
If the viewer is running without the administrator’s permission in Windows Vista / 7, you may not change a folder
when saving a video as AVI file.
Audio
• : Sets audio of each connected channel to On/Off.
OSD
• : Select Show OSD on the Live screen.
English _101
● WEB VIEWER
CONTROLLING A CONNECTED PTZ CAMERA
Controlling PTZ
If PTZ camera is connected, the <
> icon appears on screen. When selecting corresponding camera
channel, the PTZ tab is provided to allow you to control the PTZ.
Part Names Functions
Direction Adjustment Adjusts the direction of a camera.
b
PT Speed Adjusts the PAN, TILT reaction speed.
c
Preset Sets the preset position for camera framing and moves to designated preset position
when selecting a desired preset.
Swing Moves between the preset start point and end point.
Group Moves in the path specified by combining the preset, pattern and auto pan.
Tour Moves in the path specified by combining multiple groups.
Trace Moves camera’s framing in the predefined path.
Power PTZ Click or drag on the screen to control PTZ.
Focus Adjusts the focus of the camera.
IRIS Adjusts image’s brightness by controling the camera’s iris.
ZOOM Zooms in/out the image by controling camera’s zoom.
b
c
102_ web viewer
web viewer
To set a preset
1. Click <
> button to display “Preset” window.
2. Click <
> to select a desired preset number.
3. Enter the name of preset.
4. Use direction keys to adjust the direction which camera
aims at.
5. Click the <RECORD> button.
To activate the preset
1. Click <
> button to display “Preset” window.
2. Select a desired preset to activate from the list.
The camera’s framing moves to the preset position.
To activate Swing, Group, Tour and Trace
You can activate listed functions in the same manner as using a preset. For more information, refer to
corresponding user manul of applicable camera.
M
Only selective functions of the camera can be supported, depending on camera.
English _103
● WEB VIEWER
Controlling OSD Menu
If connected PTZ camera supports the OSD menu, press the <
> to enter camera’s menu screen to
change its settings.
Part Names Functions
Direction Adjustment You can go to a desired menu.
ENTER Selects a desired item.
b
Menu On/Off You can On/Off camera’s OSD menu settings.
M
For more information about camera’s OSD menu, refer to corresponding user manul of each camera.
b
104_ web viewer
web viewer
USING SEARCH VIEWER
The Search Viewer screen consists of following :
Up to 3 users can access simultaneously.
Menu Functions
Menu Selection Switches to the corresponding menu screen by clicking each menu.
bAddress, Name, Time Displays the IP, model name, time, etc. of connected DVR.
cSplit Mode Selection Selects the type of split screen and selects the channel displayed in Display Pane.
Backup Connected camera videos are backed up manually.
CAPTURE Saves current video for selected channel in designated path.
PRINT Prints current video image for selected channel through designated printer.
AVI Save Records the live video in AVI file format in designated path, and then stops recording.
Recording status icon is displayed on screen during recording.
Audio Sets the sound connected to each channel to ON/OFF.
OSD Select the format of OSD information that will be displayed.
Calendar Displays the video-recorded date in blue and today in white. Click the date in blue color
to display the recorded video information in timeline.
Overlapped Data Displays and zooms in/out recorded video data. If overlapping data found, this function
selects one of them to play.
b
c
English _105
● WEB VIEWER
Menu Functions
Play Control Adjusts current video’s playback speed and played time position.
Recording Color Displays the corresponding color depending on recorded data type if you place your
mouse cursor on that area.
Display Pane Plays corresponding data on the screen if you select a search result.
Logout Click Logout icon for logout.
User ID Displays the user's ID.
Searching the Recorded Video in the Calendar
Dates having recorded video are marked in blue.
Click a date marked blue to display video information on the
timeline. When you click <
>, it will be synchronized
with the system time (date) of the current PC.
To search by date
You can select the search date by using calendar.
1. Click <
> or <
> to select the year to search.
2. Click <
> or <
> to select the month to search.
The date including data appears in blue and today
appears in red.
3. Click the date to search in calendar.
The first image of searched video data on the date is displayed on screen and the data is displayed in the
timeline.
4. To search video data on today, click <
>.
Today’s date is selected.
(PC Time)
To adjust timeline
If searched data are overlapping, you can select a desired data, move its playback time point, and zoom in/
out the timeline.
1. Select the number of data to search if data is overlapping.
It appears only when data are overlapped and assigns <0> to the most recent data.
2. Click your desired time point to play on the timeline.
The playback start point is moved.
3. Click < >, < > to zoom in/out the zoom factor to display time.
4. To show the previous/next timeline in zoomed-in status, click < > or < > to go to the left or right.
106_ web viewer
web viewer
Names and Functions of Play Buttons
Moves backward by 10 minutes from the current playing
point.
b Plays in reverse at doubled speed. The playback speed is
doubled up to 64x speed.
c Moves backward by 1 second from current playing point.
Moves forward by 1 second from current playing point.
Plays at doubled speed. The playback speed is doubled up to 64x speed.
Moves forward by 10 minutes from the current playing point.
Moves to the recording start point on the corresponding timeline.
Plays in reverse.
Stops playing. When resuming playback, it is played from the recording start point.
Pauses playing. When resuming playback, it is played from the stopped point.
Plays normally.
Moves to the recording end point on the corresponding timeline.
If you back up searched videos
After you manually enter channels, date, and time, etc. that you want to back up, you can back up recorded videos.
1. Please, setup the details of the backup process.
• Channel : Channels to back up are selected.
You can select multiple channels redundantly.
• Backup intervals : To setup <Start> and <End> times to
back up.
• Type : Backup format is selected.
- AVI : Live videos are stored in AVI file format. This file
format can be played using various viewers, such as
Windows Mediaplayer on your PC.
If Windows needs to install a codec, please run x264_dvr.exe in
the folder 'codec' that is generated during avi backup.
- SEC : Live videos are stored in SEC file format. To be playable directly on PC.
When backing up SEC, you can select whether or not to use a password. After checking <USE password>, please set
up your password.
• Filename : You can change the backup file name.
• Path : Specifies the path to store backup videos.
2. After backup configuration is completed, please click the <Backup> button.
3. When backup is completed, the <File Backup> screen
pops up.
If you click <Open folder.>, you can verify the path in
which backup videos are stored.
b c
English _107
● WEB VIEWER
VIEWER SETUP
You can configure the DVR settings remotely on the network.
To configure the DVR settings, click <Setup>.
System
You can configure the various settings of the DVR system.
Date/Time/Language
For more information, refer to <Date/Time/Language> in the <System Setup> menu. (Page 44)
1. Select <Date/Time/Language> in the System menu.
2. Configure the DVR settings according to your system environment.
• Date/Time
Set the date and time.
• Time Synchronization Setup
Set the time synchronization.
• Display
Date Format : Set the date type.
Time : Select a time format to display on the screen.
• DST (Daylight Saving Time)
DST is displayed an hour ahead of the standard time of the time zone.
• Language
Select a preferred language for the DVR.
Holiday
You can set specific dates to Holidays according to your preferences.
For more information, refer to <Setting Holiday> in the <System
Setup> menu. (Page 45)
108_ web viewer
web viewer
Permission Management
For more information, refer to <Permission Management> in the <System Setup> menu. (Page 46)
• Admin
You can change the admin ID or the password.
You can type the ID with alphanumeric characters only.
For the password, use alphabets and special characters excluding <\> and
<">.
If you click < >, a simple guideline to setting the password is shown.
• Group
Users are classified into groups and the permission can be
set according to the group.
First of all, add a group.
• User
You can add, change or remove a user or users.
English _109
● WEB VIEWER
• Setup
You can set the user permission.
System Management
For more information, refer to <System Management> in the <System Setup> menu. (Page 50)
• System Information
You can see information of the current system.
Check the Software Version, Broadcast Format and MAC Address.
Device
You can check a list of devices that are connected to the DVR and configure the necessary settings.
Click <Device> in the menu screen.
For more information, refer to “Setting the Device”. (Page 54)
Camera
• Camera
You can configure the settings of the camera that is connected to the
DVR.
Vx.xxh_yymmddhhmmss
110_ web viewer
web viewer
• Privacy Region
You can specify a certain area of the camera video to be protected for
your privacy.
• PTZ
You can configure the settings of the PTZ camera that is connected to
the DVR.
Set the ID and protocol.
• Type
You can set the camera type by selecting it manually/automatically.
English _111
● WEB VIEWER
Storage Device
You can check and change the settings of the storage device.
• Device
You will see a list of storage devices that are connected to the DVR.
You can check the type, used/total, usage and status of the device.
• HDD Alarm
You can set the alarm output channel and the alarm duration for an
error.
Remote Device
You can see a list of remote devices including PTZ cameras and
system keyboards that are connected to the RS-485 port of the DVR
and configure the necessary settings.
112_ web viewer
web viewer
POS Device
You can set the channel, preset and communication port of the POS
device that is connected to the DVR.
M
You cannot set to use the POS device remotely.
Monitor
• Monitor
You can configure the monitoring screen settings and set the output
system.
• Mode
You can switch between live mode and play mode.
English _113
● WEB VIEWER
Record
For more information, refer to <Setting the Recording>. (Page 64)
Recording Schedule
If you set a recording schedule for a specific date and time, the
recording will start at that specific time.
- Apply to All CH : Click <Apply to All CH> to display the
confirmation window.
Event Record Duration
You can set the start and end times of recording that will be activated
if an event occurs.
114_ web viewer
web viewer
REC Quality & Resolution
• Standard/Event
You can set the resolution, frame rate and recording quality for each
channel.
Record Option
You can set the Disk End Mode.
Event
For more information, refer to <Setting the Event>. (Page 67)
Sensor Detection
You can set the sensor operation mode and the synchronized camera
as well as the alarm output type and the duration.
English _115
● WEB VIEWER
Motion Detection
You can set the motion detection mode and the sensitivity
as well as the alarm output type and the duration.
• Motion Region
Set the target motion detection area.
Video Loss Detection
You can set the alarm output time if a video loss occurs.
Tampering Detection
You can set whether to generate alarm and its dwell time for video
tampering events.
116_ web viewer
web viewer
Alarm Schedule
You can schedule the alarm output according to the day of the week
and the time.
The default setting is Event Sync, which activates the alarm only if an
event occurs.
Network
For more information, refer to <Network Configuration>. (Page 72)
Connection Mode
A remote user can access the DVR via the network to check the current mode and the IP address.
• Interface
You can set the network connection route.
• Port
You can configure the protocol related settings.
English _117
● WEB VIEWER
• Alarm
Set the alarm.
DDNS
You can check the DDNS settings.
Live Transfer
Sets the quality of the image that is transferred from the DVR to the network.
• Live Transfer
A remote user can set the image resolution of the transferred data.
118_ web viewer
web viewer
Mailing Service
You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users.
• SMTP
You can set the server that sends mails and specify if you use the
authentication process.
• Event
You can set the event interval and specify which events the server
sends mails for.
• Group
You can add a group to receive the mail if an event occurs and set the
permission to receive the event mail for each group.
English _119
● WEB VIEWER
• Recipient
You can add a user or users who will receive the mail.
SNMP
You can configure the settings for the SNMP protocol.
INFORMATION
Click <Information>.
Displays the model name of connected DVR and the version of Web Viewer.
120_ web viewer
web viewer
CONNECTING WEB VIEWER (Mac)
Safari on MAC.
If you want to use HRD-Series DVR Web Viewer with Safari Browser on a Mac, please refer to this user guide
and install Multi Viewer with firmware upgrade if necessary.
• Mac OS versions available : 10.6 or later version
• Silverlight : 5 or later
• Safari : 5 or later
1. Click [Click now to Install] to display the installation
screen as shown.
2. Double-click the [Silverlight.pkg] icon to display the
Silverlight plug-in installation screen as shown.
3. Click [Continue] to start installing Silverlight plug-in.
When done, you will see the screen as below.
4. Click [Close] to exit from the Silverlight plug-in installation
screen.
English _121
● WEB VIEWER
• If Microsoft Silverlight plug-in is already installed
1. Use a web browser to connect to the DVR.
2. If Silverlight plug-in is already installed, you will see the
login screen as shown.
3. If the login screen does not appear, check if the DVR set is
connected properly with a valid IP address.
M
If automatic proxy is activated and an invalid DNS server is specified while configuring network, the Internet access
may not be available.
For more details on using the Web Viewer, please refer to “Connecting Web Viewer (Windows)”. (Page 94)
• If Safari 6.1 or higher is used, set it as shown below.
1. Select Safari "Preferences > Security > Internet Plugin".
2. Click on silver light plugin.
3. Set the DVR address to <Allow Always> or <Allow>.
4. Select an address for DVR in <Run in Unsafe Mode> and
set the website to <Trust> on the popup.
5. When the program has finished installing, open the web
viewer again to login.
122_ web viewer
web viewer
USING LIVE VIEWER (Mac)
The Live Viewer screen consists of following :
Menu Functions
Name, Address
Displays a connected DVR’s IP address and model name.
b
Menu Selection
Consists of <
Live
> ,<
About
> and <
LOGOUT
> menu.
c
Split Mode Selection
These buttons are used for the screen split and full screen mode.
Supports up to a maximum of 9 channels due to performance constraints of Silverlight.
Name, Address
Displays a connected DVR’s IP address and model name.
Audio
Sets the sound connected to each channel to ON/OFF.
DVR Tim, PC Time
Select <
DVR Time
> or <
PC Time
> for the OSD time information display setting of the Live
Viewer.
Change Channel
Switches into previous/next channel or perform Auto Sequence.
Click Auto Sequence button to display the Time Interval Selection menu.
CAPTURE Saves current video for selected channel in designated path.
PRINT Prints current video image for selected channel through designated printer.
RECORD
Starts and stops recording.
If you cannot play the file recorded from the web, please install the H.264 CODEC.
ex) MAC: perian_1.2.3.dmg (http://perian.org)
c
b
English _123
● WEB VIEWER
Menu Functions
Channel Indicates connected DVR's channels.
PTZ Controls connect PTZ camera(s).
Display Pane Displays the video of camera connected to DVR.
MOBILE VIEWER
What is Mobile Viewer?
Mobile Viewer is management software that enables you to connect to DVR (Digital Video Recorder) remotely
and control the video playback and PTZ operations (if configured) in real time.
Key Features
• Remote access via Smart phone
• Voice Recognition
• 1-split and 4-split modes supported in Live Viewer
• Supports single channel search function
• Switch channels using the touch-sensitive LCD panel
• PTZ camera operations supported
(complies with the protocol of the connected DVR)
• Up to 16 channels supported
Compatible Smartphone
This application is optimized for
• iOS v6.1, v7.0 (iPhone 4/5, iPad 2/3/4)
• Optimized for Android v4.x.
Some features (e.g. Favorite list) may work abnormally in Android v2.x.
Android v5.x or above may show v.loss due to OS compatibility.
Use lower resolutions for multi-split view.
M
For more information, refer to the user manual.
(www.hanwha-security.com)
124_ backup viewer
SEC BACKUP VIEWER
You can play a file that is backed up in the format of SEC.
Backup in SEC format produces backup data file, library file and self-executable viewer file.
If you run the backup file viewer, the backup data file will be automatically played.
Recommended System Requirements
PCs with a lower specification than the recommended below may not fully support forward/backward and
high-speed playback.
• OS : Windows XP professional, Windows Vista, Windows 7
• CPU : Intel i5 2.8GHz or faster
• RAM : DDR PC-3200 1G or more
• VGA : Geforce 6200 or higher
Part Names Functions
Split Screen
Set the screen’s aspect ratio to be displayed.
The screen switches to the selected split screen mode.
backup viewer
b
c
SRD-1694_CAM 01
English _125
● BACKUP VIEWER
Part Names Functions
b
Digital Zoom
Enlarge the image by up to 100 times as big as the current one.
Press the Zoom In ( ) button the enlarge the image; press the Zoom Out
( ) button to shrink the image.
You can also use the slide bar ( ) in the pop-up window to zoom in/out.
Press ( ) on a size-changed video to restore the default zoom factor
(100%).
If you enlarge the image by more than 200%, the enlarged area will be
marked on the digital zooming screen. Click on the marked area and move it
to a desired position.
The digital zooming is applied to all backup viewer. When the digital zooming
is canceled, the video size will restore the default rate of 100%.
c
Screen Printout
Saves the current video’s image as in an image file. Supports jpeg file format.
Prints out the current screen. You should have installed the appropriate printer
driver before you can print out the screen.
Audio
/ A toggle button. Each time you press this button, the audio output will toggle
between activated and deactivated.
You can adjust the volume level from 0 to 100.
Watermark / Press the button to enable file tampering detection, to detect data file forging.
Deinterlace You can enable the De-interlace function.
Show OSD
Check the OSD checkbox to display the OSD information on the backup
playback screen.
Information such as backup date, day of the week, time, model name, and
channel number will be displayed on the screen.
Maintain aspect
ratio/Full screen
Maintains the aspect ratio of the playback screen.
Plays the video on a full screen.
Enlarge /
Reduce Timeline
Collapses the time range that is displayed on the range bar of the storage
time. You can collapse the range bar until the overall range is shortened to
24 hours.
Enlarges the time range that is displayed on the range bar of the storage
time. You can enlarge the range bar until the overall range is extended to
1 minute.
Restore Timeline Restores the timeline to the default.
Display of storage time range Displays the time range of a stored video file.
You can move the gridline of the range bar to select a time point to play.
Playback Control You can adjust the video playback of the timeline.
M
If it has a high recording rate and is played at high speed playback of 16x or higher speed in the backup viewer,
actual playback speed may not reach the set playback speed.
126_ appendix
appendix
PRODUCT SPECIFICATION
Item Details
HRD-442 HRD-842 HRD-1642
Video Inputs
4channel BNC :
AHD(2MP, 4MP), TVI(2MP),
CVI(2MP), NTSC/PAL
8channel BNC :
AHD(2MP, 4MP), TVI(2MP),
CVI(2MP), NTSC/PAL
16channel BNC :
AHD(2MP, 4MP), TVI(2MP),
CVI(2MP), NTSC/PAL
Resolution
2560x1440, 1920 x 1080, 960 x 480, 704 x 480 / 960 x 576, 704 x 576
Live
Frame rate 120fps , 100fps
240fps , 200fps 480fps , 400fps
Resolution
2560x1440, 1920 x 1080, 960 x 480, 704 x 480, 960 x 576, 704 x 576
Multi Screen display 1/4//PIP/Sequence
1/4/7/9/PIP/Sequence 1/4/7/9/13/16/16A/PIP/
Sequence
Performance
Operating System Embedded Linux
Recording
Compression H.264, Wisestream
Record Rate
yHRD-442
NTSC : Up to 60fps@4MP / PAL : Up to 50fps@4MP
NTSC : Up to 120fps@1920 x 1080 / PAL : Up to 100fps@1920 x 1080
NTSC : Up to 120fps @ 1280 x 720, 928x480, 704X480, 704X240, 352X240
PAL : Up to 100fps @ 1280 x 720, 928x576, 704x576, 704x288, 352x288
yHRD-842
NTSC : Up to 120fps@4MP / PAL : Up to 100fps@4MP
NTSC : Up to 240fps@1920 x 1080 / PAL : Up to 200fps@1920 x 1080
NTSC : Up to 240fps @ 1280 x 720, 928x480, 704X480, 704X240, 352X240
PAL : Up to 200fps @ 1280 x 720, 928x576, 704x576, 704x288, 352x288
yHRD-1642
NTSC : Up to 240fps@4MP / PAL : Up to 200fps@4MP
NTSC : Up to 480fps@1920 x 1080 / PAL : Up to 400fps@1920 x 1080
NTSC : Up to 480fps @ 1280 x 720, 928x480, 704X480, 704X240, 352X240
PAL : Up to 400fps @ 1280 x 720, 928x576, 704x576, 704x288, 352x288
Mode
Manual, Schedule (Continuous/Event), Event(Pre/Post), Time lapse (1~30 fps(N),
1~25fps(P))
English _127
● APPENDIX
Item Details
HRD-442 HRD-842 HRD-1642
Recording
Event
Video Loss, Motion(Level 1~10), Alarm Input, Tampering(Level Low,Medium, High)
Overwrite modes Continuous
Pre-alarm Up to 30 sec (5, 10, 20, 30 Sec)
Post-Alarm Up to 6 hour (5, 10, 20, 30 sec, 1, 3, 5, 10, 20 min, 1, 2, 3, 4, 5, 6 hour)
Search & Playback
Search mode
Date/time, Event, Back up, POS(SD Signal only), Motion (
※
All Search Included
Preview Function)
Playback function
Fast Forward/Backward (x2,x4,x8,x16,x32,x64) ※ Backward Play with I-frame
Only,
Slow Forward/Backward (x1/2,x1/4,x1/8)
Step Forward/Backward ※ Backward Play with I-frame Only
Simultaneous
playback 4CH(Local Monitor, CMS)
8CH(Local Monitor, CMS) 16CH(Local Monitor, CMS)
Network (IPv4) Transmission speed
Record(Main) Stream) 4MP : 15fps/CH, 1080p/720p/WD1/4CIF/CIF : 30fps/CH(N),
25fps/CH(P)
Network(Sub) Stream) WD1/4CIF : 12fps/CH, 2CIF/CIF/QVGA/QCUF : 30fps/CH(N),
25fps/CH(P)
Network (IPv4)
Transmission
Bandwidth Up to 64Mbps
Bandwidth control Selectable
Stream Record Stream and Network Stream Selectable (at monitoring Viewer)
Remote users
Maximum Search(3)/Live Unicast(10)/Live Multicast(20)
Protocol support
TCP/IP, DHCP, PPPoE, SMTP, NTP, HTTP, DDNS, RTP, RTSP, SNMP SUNAPI(SUNAPI
2017. 07)
Web Browser
Windows OS : Internet Explorer 8, 9, 10, Firefox 3.6 or higher, Chrome 12 or higher
Mac OS : Safari 5 or higher, Firefox 3.6 or higher
Viewer Software SSM, Webviewer, SmartViewer, iPOLiS mobile viewer, WiseNet Mobile (~7. 2017)
128_ appendix
appendix
Item Details
HRD-442 HRD-842 HRD-1642
Smart phone
Platform Android, iOS
Protocol support RTP, RTSP, HTTP, CGI(SUNAPI 2017. 07)
Control
Live(4ch) : Multi-Profile
Support
Playback(1ch)
Live(8ch) : Multi-Profile Support
Playback(1ch)
Remote users
Maximum Search (3), Live Unicast (10), Multicast (20)
Storage
Internal Up to 2 SATA HDDs
(0~8TB HDD)
Up to 4 SATA HDDs
(0~8TB HDD)
Up to 8 SATA HDDs
(0~8TB HDD)
External (e-SATA
Interface) USB(for Backup)
e-SATA, USB(for Backup)
File Format (Back-
up) BU(DVR Player), SEC(Include Player), AVI
Security Password Protection 1 Admin, 10 Group , 10 User per 1 Group
Data Authentication Watermark
Easy Configuration Easy Configuration P2P (TUTK)(2017.07)
Interface
Monitors
VGA 1 VGA (1920x1080, 1280x1024, 1280x720)
HDMI
1 HDMI (4K(3840 x 2160), 2K(2560 x 1440), 1920x1080, 1280x1024, 1280x720)
Composite(Spot) BNC(1CH) ※ Included OSD On Screen, Multi mode Support
Loop Outputs -
Audio
Inputs/Output 4CH line in / 1CH line out
8CH line in (Built in 4CH,
Option : Audio Extension
Cable)/ 1CH line out
16CH line in (Built in 4CH,
Option : Audio Extension
Cable)/ 1CH line out
Compression G.711
Sampling rate 8KHz
Alarm Inputs/Outputs
Terminal 4 Inputs (NO/
NC) / Terminal 2 relay
Outputs (NO/NC), Rating :
30V DC/2A, 250V
AC/0.25A
Terminal 8 Inputs (NO/NC)
/ Terminal 4 relay Outputs
(NO/NC), Rating : 30V
DC/2A, 250V AC/0.25A
Terminal 16 Inputs (NO/
NC) / Terminal 4 relay
Outputs (NO/NC), Rating :
30V DC/2A, 250V
AC/0.25A
Remote notification Notification via e-mail
English _129
● APPENDIX
Item Details
HRD-442 HRD-842 HRD-1642
Connections
Ethernet 1 RJ45 10/100/1000 Base-T
Serial interface RS-485(Full Duplex) for PTZ, System Keyboard
USB 2 ports(Front)
1 ports(USB 3.0, Rear),
1 ports(USB 2.0, Front)
e-SATA -
2 External SATA ports
Application support Mouse, IR Remocon
Protocol
support(RS-485)
Samsung-E/Samsung-T/Pelco-D/Pelco-p/Panasonic/ Phillips/ AD/ DIAMOND/
ERNA/ KALATEL/ VCL TP/VICON/ ELMO/GE
Protocol
support(Coaxial)
NTSC/PAL : Pelco-C (Coaxitron)
AHD : ACP(AHD Coax Protocol)
General
Electrical
Input Voltage/
Current
DC12V
Adaptor(100~250V AC
±10% , 50/60Hz)
100 ~ 240 VAC ±10%; 50/60 Hz
Power consumption
Max. 18W(1 x 2T HDD) Max. 25W (1 x 2T HDD) Max. 62W (1 x 2T HDD)
Environmental
Operating
Temperature/
Humidity
+0°C to +40°C (+32°F to +104°F) / 20% to 85% RH
Mechanical
Dimension
(W x H x D)
W370.0x H44.0 x
D320(14.57” x 1.73” x
12.6”)
W440x H88 x D384.8(17.32” x 3.46” x 15.15”)
Weight (With hard
disks)
Approx. 2.84 kg(6.26 lb) Approx. 5.24 kg (11.55 lb) Approx. 5.78 kg (12.74 lb)
Lauguage
English, French, German, Spanish, Italian, Russian, Polish, Czech, Turkish, Netherlands
Portuguese, Swedish, Danish, Rumania, Serbia, Croatia, Hungary, Greek, Finnish,
Norwegian, Korean, Japanese, Chinese(Traditional), Thai , Taiwanese (25 Language)
130_ appendix
appendix
PRODUCT OVERVIEW
• HRD-442
unit : mm(inch)
English _131
● APPENDIX
• HRD-842
unit : mm(inch)
132_ appendix
appendix
• HRD-1642
unit : mm(inch)
English _133
● APPENDIX
DEFAULT SETTING
This returns the factory default settings.
The settings are made as follows;
• Use System/Load Factory Default in MENU
The default settings are based on HRD-1642.
The default administrator ID is “admin”, and the password must be set when the user log in at the first time.
To prevent from your personal information being exposed, please change your password every 3 months. Note that the security and other
related issues caused by careless management of password shall be be in the charge of the user.
Category Details Factory Default
System Settings
Date/Time/Language Date/Time/Language
Date YYYY-MM-DD
Time Format 24 hours
Time Zone GMT
Time Synchronize OFF
DST OFF
Language English
Permission
Management
Admin ID admin
User Group All Group
Setup
Restricted Access
Backup/Record Lock/
Search/PTZ/Remote
Alarm Out/Shutdown
Auto Logout OFF
Manual Input of ID OFF
Touch Button Sound ON
Touch Button ON
System Management System Information Broadcast Format NTSC/PAL
Device Camera
Camera
Video ON
Audio OFF
CH Name CAM 01 ~ CAM 16
SEQ-Dwell Time 5 sec
Type AHD
Screen Setup
Brightness 48
Contrast 53
Color 53
EQ 3
PTZ
Port RS-485
ID Camera No.
Protocol None
Type
Type AHD
Resolution 4M
Mode Auto
EQ 3
134_ appendix
appendix
Category Details Factory Default
Device
Storage Device HDD Alarm
Check Alarm Output Port OFF
Duration OFF
Replace Alarm Output Port OFF
Duration OFF
Remote Device
Baudrate 9600
Parity None
Data 8
Stop bit 1
System Keyboard OFF
Remote Control ON(0)
POS Device ON
Monitor
Monitor
Event Display OFF
Display All
Multi CH SEQ Time 5 sec
VGA/HDMI 1920 x 1080
HDMI Resolution Auto
Detection ON
Spot Out
Multi Spot OFF
Spot Out Single
Event Display OFF
Mode Live Screen ALL
Play Screen ALL
Recording
Recording Schedule CH1~CH16 Both(Cont&Evnt)
Event Record Duration PRE Event OFF
POST Event 1 min
REC Quality/Resolution
Standard
Resolution 4M
Frame Rate 15 fps
Record Quality Level 4
Type HD
Event
Resolution 4M
Frame Rate 15 fps
Record Quality Level 4
Type HD
Record Option Disk End Mode Setup Overwrite
Disk End Beep OFF
Auto Delete OFF
English _135
● APPENDIX
Category Details Factory Default
Event
Sensor Detection
Sensor Operation OFF
Camera Camera No.
Alarm None
Alarm Duration 10 sec
Motion Detection
Mode OFF
Sensitivity Level10(high)
Alarm None
Alarm Duration 10 sec
Motion Region All Area
Video Loss Detection
Video Loss State OFF
Alarm None
Alarm Duration 10 sec
Tampering Detection
Mode OFF
Sensitivity Medium
Alarm None
Alarm Duration 10 sec
Alarm Schedule Alarm1 Event Sync
136_ appendix
appendix
Category Details Factory Default
Network
Connection Mode
Interface
IP Type Static
Transfer Bandwidth 2Mbps
IP Address 192.168.1.200
Gateway 192.168.1.1
Subnet Mask 255.255.255.0
DNS 168.126.63.1
Port
Protocol Type TCP
Device Port 4520~4524
HTTP Port 80
Secure Video Transmission OFF
Alarm Disconnect Alarm Output Port OFF
Duration OFF
DDNS DDNS Site OFF
Live Transfer Resolution CIF
Quality Low
Mailing Service
SMTP
Server OFF
Port 25
Use Authentication OFF
Secure Transfer Never
Event
Event Interval 10 min
The number of attached
images for each event 1
Use Event Transfer OFF
Group Group OFF
Recipient Permission OFF
SNMP
Enable SNMP v1 OFF
Enable SNMP v2 OFF
Enable SNMP v3 OFF
English _137
● APPENDIX
TROUBLESHOOTING
Symptom Countermeasures
The system does not turn on and the indicator on the
front panel does not work at all.
yCheck if the power supply system is properly connected.
yCheck the system for the input voltage from the power source.
yIf the problem persists even after you have taken the above actions,
check the power supplier and replace it with a new one if neccessary.
Some channels display just a black screen even if
they receive video sources.
yCheck if the camera connected to the system properly displays the
image. Sometimes, this problem may occur on a camera that is not
properly connected to the video source.
yCheck if the camera is properly supplied with power.
ySometimes, this problem may occur on a channel with weak video
signal from a video distributor that is connected to multiple systems. In
this case, input the video source of the camera directly into the DVR.
This may find the cause and solve the problem.
If I press the [REC] button on the front panel, the
REC indicator does not flash, nor the player start
recording.
yCheck if there is a free space on the HDD for the recording.
yCheck if the record mode is set to ON in the record mode setting.
The screen displays the logo image repeatedly. yThis may occur from a problem with the main board, or the related
software is corrupt.
Contact the nearest service center for more information.
The Channel button does not work on the Live
screen.
yThe Channel button does not work if the current screen is in the event
monitoring mode.
In the event monitoring screen, press the [ALARM] button to exit the
screen and select a channel.
The cursor will not move to the Start button when I
start the calendar search.
yCheck if the channel and the date that you want to play are marked
with the V symbol.
Both channel and date should be checked before you can start playing
with the Start button.
When the alarm sounds, I press the [ALARM] button
on the front panel to release the alarm but it does
not work. The alarm persists and I could not set it off
in any way.
yPress the [MENU] button on the front panel to release the alarm in the
following way:
1) To release the event monitoring mode : Monitoring Mode – set the
duration of the event monitoring to Off.
2) To release the alarm sound : Event Record Mode - Alarm (Motion
Detection/Video Loss/Tampering Detection) – deactivate the alarm
sound.
3) To release the event : Event Record Mode - Alarm (Motion Detection/
Video Loss/Tampering Detection) – set the mode to Off.
No response is made even if I press the [PTZ] button
on the Live screen.
yMenu Camera Check if the current protocols and other settings
in the PTZ device are properly configured according to the PTZ camera.
138_ appendix
appendix
Symptom Countermeasures
I've found that the DVR does not recognize as many
disks as installed when I have connected multiple
external HDDs to the DVR.
yIt takes time for the DVR to recognize multiple external HDDs. Try again
in a moment and if the problem (of failure to recognize as many HDDs
as connected) persists, it may occur due to a mechanical error of the
HDD installed. Try again with a different HDD.
A message of “Need to reset date/time.” Is displayed
on the screen.
yThis message is displayed if there occurs a problem with the time
setting of the internal clock or an error in the clock itself.
Contact the retailer or the service center for more information.
The time bar is not displayed in Search mode. yThe timeline can switch between normal and extension mode.
In extension mode, the time bar may not be displayed in the current
timeline. Switch to normal mode or use the left or right button to
navigate through the time bar.
The “NO HDD” icon and an error message are
displayed.
yCheck the HDD for connection. If the problem persists in a normal
condition, contact the nearest service center to have the HDD checked
by the service personnel.
I have installed an additional HDD on the DVR but it
does not recognize the HDD.
ySee the compatibilty list to check if the additional HDD is supported by
the DVR. For the compatibility list, contact the retailer where you
purchased the DVR.
I have connected an external storage device (external
SATA HDD) to the DVR but the DVR seems not to
recognize it.
ySee the compatibility list of external storage devices to check if the
connected device is supported by the DVR.
For the compatibility list, contact the retailer where you purchased the
DVR.
If I press the ESC key in full screen mode of the
WebViewer, the system does not switch to a normal
split mode.
yPress the ALT+TAB keys to select ‘ACTIVE MOVIE’ and press the ESC
key again. The system will switch to a normal split mode.
I found it difficult to configure the network settings if
using the default search, backup and router settings.
yFor more information, refer to the user manual.
yIf you want to check the basics of the product for a quick start, refer to
the quick start guide (backup, search).
yIf you use the router for network connection, refer to the “Connecting
to the Internet using the router” section in this manual.
I forgot the password. yContact the DVR administrator for help.
Backup data is just not played by the PC or DVR. yWhen you are backing up data, you have choices about the player
either: PC or DVR. Make your selection before proceeding.
yIf you are using the PC to play the data, the format of the backup file
should be either SEC.
yIf you are using the DVR for this purpose, formatting backup files should
be done by the DVR.
My player does not switch to Live mode while in
playback.
yPress the Stop [@] button on the DVR or the remote control, or click the
[ ] icon on the launcher to switch to Live mode.
English _139
● APPENDIX
Symptom Countermeasures
Recording does not work. yIf your player does not display a Live image at all, that indicates
recording does not work so first check if you see an image on the
screen.
yRecording does not work if the recording settings are not properly
configured.
1) Manual Record: Press the [REC] button on the front panel of the DVR
or on the remote control to start recording.
2) Scheduled Record: Specify a desired time in Menu – Record –
Recording Schedule. Recording will start at the specified time.
-<Continuous> Record: Recording will proceed in any conditions
at the specified time.
-<Event> Record: When an event occurs, recording will perform
only if the event is of alarm, motion detection, video loss and
Tampering Detection.
If there is no event found, recording will not perform.
-<Continuous / Event> Record: If there is no event found,
Continuous recording will perform. Whereas, if an event occurs,
Event recording will perform.
The image quality of the recording data is not good. yIncrease the resolution and quality level in Menu – Record – Quality /
Resolution.
1) Resolution: Select a bigger size when specifying the recording size.
(720P/1080P>WD1>4CIF>2CIF>CIF)
The recording image in the CIF format shows a deteriorated quality
as it is enlarged from a small-sized image.
2) Record Quality: Specify a bigger level for the recording quality.
yIf you increase the resolution and the recording quality, the data size
increases accordingly. So the HDD will be filled faster. Overwriting will
overwrite the existing data so recording will proceed at a shorter
interval.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom
to share and change it. By contrast, the GNU General Public License is
intended to guarantee your freedom to share and change free software
to make sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s software and
to any other program whose authors commit to using it. (Some other
Free Software Foundation software is covered by the GNU Lesser
General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price.
Our General Public Licenses are designed to make sure that you have
the freedom to distribute copies of free software (and charge for this
service if you wish), that you receive source code or can get it if you
want it, that you can change the software or use pieces of it in new free
programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone
to deny you these rights or to ask you to surrender the rights. These
restrictions translate to certain responsibilities for you if you distribute
copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis
or for a fee, you must give the recipients all the rights that you have. You
must make sure that they, too, receive or can get the source code. And
you must show them these terms so they know their rights.
We protect your rights with two steps:
(1) copyright the software, and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain
that everyone understands that there is no warranty for this free
software. If the software is modified by someone else and passed on,
we want its recipients to know that what they have is not the original, so
that any problems introduced by others will not reflect on the original
authors’ reputations.
Finally, any free program is threatened constantly by software patents.
We wish to avoid the danger that redistributors of a free program will
individually obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear that any patent must
be licensed for everyone’s free use or not licensed at all. The precise
terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin S
0. This License applies to any program or other work which contains a
notice placed by the copyright holder saying it may be distributed under
the terms of this General Public License. The “Program”, below, refers
to any such program or work, and a “work based on the Program”
means either the Program or any derivative work under copyright law:
that is to say, a work containing the Program or a portion of it, either
verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term
“modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of running
the Program is not restricted, and the output from the Program is
covered only if its contents constitute a work based on the Program
(independent of having been made by running the Program). Whether
that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s
source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices
that refer to this License and to the absence of any warranty; and give
any other recipients of the Program a copy of this License along with
the Program.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of
it, thus forming a work based on the Program, and copy and distribute
such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices
stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in
whole or in part contains or is derived from the Program or any
part thereof, to be licensed as a whole at no charge to all third
parties under the terms of this License.
c) If the modified program normally reads commands interactively
when run, you must cause it, when started running for such
interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that you provide a
warranty) and that users may redistribute the program under these
conditions, and telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but does not normally
print such an announcement, your work based on the Program is
not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves,
then this License, and its terms, do not apply to those sections when
you distribute them as separate works. But when you distribute the
same sections as part of a whole which is a work based on the
Program, the distribution of the whole must be on the terms of this
License, whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise the
right to control the distribution of derivative or collective works based on
the Program.
In addition, mere aggregation of another work not based on the
Program with the Program (or with a work based on the Program) on a
volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it,
under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable
source code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for
software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to
give any third party, for a charge no more than your cost of
physically performing source distribution, a complete machine-
readable copy of the corresponding source code, to be distributed
under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
OPEN SOURCE ANNOUNCEMENT
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete
Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@hanwha.com
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source
distribution might be charged.
M
For more details about Open Source, refer to the CD.
• GPL Software : linux kernel, Sysvinit, dosfstools, wget, msmtp, busybox, cdrtools, dvd+rw-tools, iconv, smartctl, uboot, minicom, openssl, bash,
lm_sensors, parted, procps, util-linux 2.19.1, xfsprogs 3.1.7
• LGPL Software : glibc, vmstat, inetutils, calendarview.js, libiconv
• OpenSSL License : OpenSSL
• Boost Software License: Boost-1.43.0 (http://www.boost.org/)
• COMMON DEVELOPMENT AND DISTRIBUTION LICENSE: cdrtools 2.01.01
• FreeType Project LICENSE: freetype2
• RSA MD4 or MD5 Message-Digest Algorithm License : MD5 Message Digest Code
• MIT License : JQuery, Prototype JavaScript framework, FJCore
c) Accompany it with the information you received as to the offer to
distribute corresponding source code. (This alternative is allowed
only for noncommercial distribution and only if you received the
program in object code or executable form with such an offer, in
accord with Subsection b above.)
The source code for a work means the preferred form of the work for
making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control
compilation and installation of the executable. However, as a special
exception, the source code distributed need not include anything that is
normally distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating system on
which the executable runs, unless that component itself accompanies
the executable.
If distribution of executable or object code is made by offering access to
copy from a designated place, then offering equivalent access to copy
the source code from the same place counts as distribution of the
source code, even though third parties are not compelled to copy the
source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this License. Any attempt otherwise
to copy, modify, sublicense or distribute the Program is void, and will
automatically terminate your rights under this License. However, parties
who have received copies, or rights, from you under this License will not
have their licenses terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you have not
signed it. However, nothing else grants you permission to modify or
distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by
modifying or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License to do so, and all
its terms and conditions for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these
terms and conditions. You may not impose any further restrictions on
the recipients’ exercise of the rights granted herein. You are not
responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot distribute
so as to satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not
permit royalty-free redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only way you could
satisfy both it and this License would be to refrain entirely from
distribution of the Program.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply
and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents
or other property right claims or to contest validity of any such claims;
this section has the sole purpose of protecting the integrity of the free
software distribution system, which is implemented by public license
practices. Many people have made generous contributions to the wide
range of software distributed through that system in reliance on
consistent application of that system; it is up to the author/donor to
decide if he or she is willing to distribute software through any other
system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be
a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Program under this License may add
an explicit geographical distribution limitation excluding those countries,
so that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if
written in the body of this License.
9. The Free Software Foundation may publish revised and/or new
versions of the General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies a version number of this License which applies to it and “any
later version”, you have the option of following the terms and conditions
either of that version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number
of this License, you may choose any version ever published by the Free
Software Foundation.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to the author
to ask for permission. For software which is copyrighted by the Free
Software Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be guided by the
two goals of preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest
possible use to the public, the best way to achieve this is to make it free
software which everyone can redistribute and change under these
terms.
To do so, attach the following notices to the program. It is safest to
attach them to the start of each source file to most effectively convey
the exclusion of warranty; and each file should have at least the
“copyright” line and a pointer to where the full notice is found.
one line to give the program’s name and an idea of what it does.
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 2 of the License, or (at your
option) any later version.
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
the GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software Foundation,
Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
Also add information on how to contact you by electronic and paper
mail. If the program is interactive, make it output a short notice like this
when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details
type ‘show w’. This is free software, and you are welcome to
redistribute it under certain conditions; type ‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should show the
appropriate parts of the General Public License. Of course, the
commands you use may be called something other than ‘show w’ and
‘show c’; they could even be mouse-clicks or menu items--whatever
suits your program.
You should also get your employer (if you work as a programmer) or
your school, if any, to sign a “copyright disclaimer” for the program, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
‘Gnomovision’ (which makes passes at compilers) written by James
Hacker.
signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This
General Public License does not permit incorporating your program into
proprietary programs. If your program is a subroutine library, you may
consider it more useful to permit linking proprietary applications with the
library. If this is what you want to do, use the GNU Lesser General
Public License instead of this License.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute verbatim copies of this license
document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software
and other kinds of works.
The licenses for most software and other practical works are designed
to take away your freedom to share and change the works. By contrast,
the GNU General Public License is intended to guarantee your freedom
to share and change all versions of a program--to make sure it remains
free software for all its users. We, the Free Software Foundation, use the
GNU General Public License for most of our software; it applies also to
any other work released this way by its authors. You can apply it to your
programs, too.
When we speak of free software, we are referring to freedom, not price.
Our General Public Licenses are designed to make sure that you have
the freedom to distribute copies of free software (and charge for them if
you wish), that you receive source code or can get it if you want it, that
you can change the software or use pieces of it in new free programs,
and that you know you can do these things.
To protect your rights, we need to prevent others from denying you
these rights or asking you to surrender the rights. Therefore, you have
certain responsibilities if you distribute copies of the software, or if you
modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis
or for a fee, you must pass on to the recipients the same freedoms that
you received. You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they know their
rights.
Developers that use the GNU GPL protect your rights with two steps:
(1) assert copyright on the software, and (2) offer you this License giving
you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains
that there is no warranty for this free software. For both users’ and
authors’ sake, the GPL requires that modified versions be marked as
changed, so that their problems will not be attributed erroneously to
authors of previous versions.
Some devices are designed to deny users access to install or run
modified versions of the software inside them, although the
manufacturer can do so. This is fundamentally incompatible with the
aim of protecting users’ freedom to change the software. The
systematic pattern of such abuse occurs in the area of products for
individuals to use, which is precisely where it is most unacceptable.
Therefore, we have designed this version of the GPL to prohibit the
practice for those products. If such problems arise substantially in other
domains, we stand ready to extend this provision to those domains in
future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents.
States should not allow patents to restrict development and use of
software on general-purpose computers, but in those that do, we wish
to avoid the special danger that patents applied to a free program could
make it effectively proprietary. To prevent this, the GPL assures that
patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and
modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of
works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this
License. Each licensee is addressed as “you”. “Licensees” and
“recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work
in a fashion requiring copyright permission, other than the making of an
exact copy. The resulting work is called a “modified version” of the
earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work
based on the Program.
To “propagate” a work means to do anything with it that, without
permission, would make you directly or secondarily liable for
infringement under applicable copyright law, except executing it on a
computer or modifying a private copy. Propagation includes copying,
distribution (with or without modification), making available to the public,
and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other
parties to make or receive copies. Mere interaction with a user through
a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the
extent that it includes a convenient and prominently visible feature that
(1) displays an appropriate copyright notice, and (2) tells the user that
there is no warranty for the work (except to the extent that warranties
are provided), that licensees may convey the work under this License,
and how to view a copy of this License. If the interface presents a list of
user commands or options, such as a menu, a prominent item in the list
meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for
making modifications to it. “Object code” means any non-source form
of a work.
A “Standard Interface” means an interface that either is an official
standard defined by a recognized standards body, or, in the case of
interfaces specified for a particular programming language, one that is
widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other
than the work as a whole, that (a) is included in the normal form of
packaging a Major Component, but which is not part of that Major
Component, and (b) serves only to enable use of the work with that
Major Component, or to implement a Standard Interface for which an
implementation is available to the public in source code form. A “Major
Component”, in this context, means a major essential component
(kernel, window system, and so on) of the specific operating system (if
any) on which the executable work runs, or a compiler used to produce
the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all
the source code needed to generate, install, and (for an executable
work) run the object code and to modify the work, including scripts to
control those activities. However, it does not include the work’s System
Libraries, or general-purpose tools or generally available free programs
which are used unmodified in performing those activities but which are
not part of the work. For example, Corresponding Source includes
interface definition files associated with source files for the work, and the
source code for shared libraries and dynamically linked subprograms
that the work is specifically designed to require, such as by intimate
data communication or control flow between those subprograms and
other parts of the work.
The Corresponding Source need not include anything that users can
regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same
work.
2. Basic Permissions.
All rights granted under this License are granted for the term of
copyright on the Program, and are irrevocable provided the stated
conditions are met. This License explicitly affirms your unlimited
permission to run the unmodified Program. The output from running a
covered work is covered by this License only if the output, given its
content, constitutes a covered work. This License acknowledges your
rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not
convey, without conditions so long as your license otherwise remains in
force. You may convey covered works to others for the sole purpose of
having them make modifications exclusively for you, or provide you with
facilities for running those works, provided that you comply with the
terms of this License in conveying all material for which you do not
control copyright. Those thus making or running the covered works for
you must do so exclusively on your behalf, under your direction and
control, on terms that prohibit them from making any copies of your
copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the
conditions stated below. Sublicensing is not allowed; section 10 makes
it unnecessary.
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological
measure under any applicable law fulfilling obligations under article 11 of
the WIPO copyright treaty adopted on 20 December 1996, or similar
laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid
circumvention of technological measures to the extent such
circumvention is effected by exercising rights under this License with
respect to the covered work, and you disclaim any intention to limit
operation or modification of the work as a means of enforcing, against
the work’s users, your or third parties’ legal rights to forbid
circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you
receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice;
keep intact all notices stating that this License and any non-permissive
terms added in accord with section 7 apply to the code; keep intact all
notices of the absence of any warranty; and give all recipients a copy of
this License along with the Program.
You may charge any price or no price for each copy that you convey,
and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to
produce it from the Program, in the form of source code under the
terms of section 4, provided that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified
it, and giving a relevant date.
b)
The work must carry prominent notices stating that it is released
under this License and any conditions added under section 7. This
requirement modifies the requirement in section 4 to “keep intact all
notices”.
c) You must license the entire work, as a whole, under this License
to anyone who comes into possession of a copy. This License will
therefore apply, along with any applicable section 7 additional
terms, to the whole of the work, and all its parts, regardless of
how they are packaged. This License gives no permission to
license the work in any other way, but it does not invalidate such
permission if you have separately received it.
d) If the work has interactive user interfaces, each must display
Appropriate Legal Notices; however, if the Program has interactive
interfaces that do not display Appropriate Legal Notices, your
work need not make them do so.
A compilation of a covered work with other separate and independent
works, which are not by their nature extensions of the covered work,
and which are not combined with it such as to form a larger program, in
or on a volume of a storage or distribution medium, is called an
“aggregate” if the compilation and its resulting copyright are not used to
limit the access or legal rights of the compilation’s users beyond what
the individual works permit. Inclusion of a covered work in an aggregate
does not cause this License to apply to the other parts of the
aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of
sections 4 and 5, provided that you also convey the machine-readable
Corresponding Source under the terms of this License, in one of these
ways:
a) Convey the object code in, or embodied in, a physical product
(including a physical distribution medium), accompanied by the
Corresponding Source fixed on a durable physical medium
customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product
(including a physical distribution medium), accompanied by a
written offer, valid for at least three years and valid for as long as
you offer spare parts or customer support for that product model,
to give anyone who possesses the object code either (1) a copy of
the Corresponding Source for all the software in the product that
is covered by this License, on a durable physical medium
customarily used for software interchange, for a price no more
than your reasonable cost of physically performing this conveying
of source, or (2) access to copy the Corresponding Source from a
network server at no charge.
c) Convey individual copies of the object code with a copy of the
written offer to provide the Corresponding Source. This alternative
is allowed only occasionally and noncommercially, and only if you
received the object code with such an offer, in accord with
subsection 6b.
d) Convey the object code by offering access from a designated
place (gratis or for a charge), and offer equivalent access to the
Corresponding Source in the same way through the same place at
no further charge. You need not require recipients to copy the
Corresponding Source along with the object code. If the place to
copy the object code is a network server, the Corresponding
Source may be on a different server (operated by you or a third
party) that supports equivalent copying facilities, provided you
maintain clear directions next to the object code saying where to
find the Corresponding Source. Regardless of what server hosts
the Corresponding Source, you remain obligated to ensure that it
is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided
you inform other peers where the object code and Corresponding
Source of the work are being offered to the general public at no
charge under subsection 6d.
A separable portion of the object code, whose source code is excluded
from the Corresponding Source as a System Library, need not be
included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any
tangible personal property which is normally used for personal, family, or
household purposes, or (2) anything designed or sold for incorporation
into a dwelling. In determining whether a product is a consumer
product, doubtful cases shall be resolved in favor of coverage. For a
particular product received by a particular user, “normally used” refers to
a typical or common use of that class of product, regardless of the
status of the particular user or of the way in which the particular user
actually uses, or expects or is expected to use, the product. A product
is a consumer product regardless of whether the product has
substantial commercial, industrial or non-consumer uses, unless such
uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods,
procedures, authorization keys, or other information required to install
and execute modified versions of a covered work in that User Product
from a modified version of its Corresponding Source. The information
must suffice to ensure that the continued functioning of the modified
object code is in no case prevented or interfered with solely because
modification has been made.
If you convey an object code work under this section in, or with, or
specifically for use in, a User Product, and the conveying occurs as part
of a transaction in which the right of possession and use of the User
Product is transferred to the recipient in perpetuity or for a fixed term
(regardless of how the transaction is characterized), the Corresponding
Source conveyed under this section must be accompanied by the
Installation Information. But this requirement does not apply if neither
you nor any third party retains the ability to install modified object code
on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a
requirement to continue to provide support service, warranty, or
updates for a work that has been modified or installed by the recipient,
or for the User Product in which it has been modified or installed.
Access to a network may be denied when the modification itself
materially and adversely affects the operation of the network or violates
the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided,
in accord with this section must be in a format that is publicly
documented (and with an implementation available to the public in
source code form), and must require no special password or key for
unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this
License by making exceptions from one or more of its conditions.
Additional permissions that are applicable to the entire Program shall be
treated as though they were included in this License, to the extent that
they are valid under applicable law. If additional permissions apply only
to part of the Program, that part may be used separately under those
permissions, but the entire Program remains governed by this License
without regard to the additional permissions.
When you convey a copy of a covered work, you may at your option
remove any additional permissions from that copy, or from any part of it.
(Additional permissions may be written to require their own removal in
certain cases when you modify the work.) You may place additional
permissions on material, added by you to a covered work, for which
you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add
to a covered work, you may (if authorized by the copyright holders of
that material) supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of
sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal notices or
author attributions in that material or in the Appropriate Legal
Notices displayed by works containing it; or
c) Prohibiting misrepresentation of the origin of that material, or
requiring that modified versions of such material be marked in
reasonable ways as different from the original version; or
d) Limiting the use for publicity purposes of names of licensors or
authors of the material; or
e) Declining to grant rights under trademark law for use of some
trade names, trademarks, or service marks; or
f) Requiring indemnification of licensors and authors of that material
by anyone who conveys the material (or modified versions of it)
with contractual assumptions of liability to the recipient, for any
liability that these contractual assumptions directly impose on
those licensors and authors.
All other non-permissive additional terms are considered “further
restrictions” within the meaning of section 10. If the Program as you
received it, or any part of it, contains a notice stating that it is governed
by this License along with a term that is a further restriction, you may
remove that term. If a license document contains a further restriction but
permits relicensing or conveying under this License, you may add to a
covered work material governed by the terms of that license document,
provided that the further restriction does not survive such relicensing or
conveying.
If you add terms to a covered work in accord with this section, you
must place, in the relevant source files, a statement of the additional
terms that apply to those files, or a notice indicating where to find the
applicable terms.
Additional terms, permissive or non-permissive, may be stated in the
form of a separately written license, or stated as exceptions; the above
requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as expressly
provided under this License. Any attempt otherwise to propagate or
modify it is void, and will automatically terminate your rights under this
License (including any patent licenses granted under the third paragraph
of section 11).
However, if you cease all violation of this License, then your license from
a particular copyright holder is reinstated (a) provisionally, unless and
until the copyright holder explicitly and finally terminates your license,
and (b) permanently, if the copyright holder fails to notify you of the
violation by some reasonable means prior to 60 days after the
cessation.
Moreover, your license from a particular copyright holder is reinstated
permanently if the copyright holder notifies you of the violation by some
reasonable means, this is the first time you have received notice of
violation of this License (for any work) from that copyright holder, and
you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the
licenses of parties who have received copies or rights from you under
this License. If your rights have been terminated and not permanently
reinstated, you do not qualify to receive new licenses for the same
material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a
copy of the Program. Ancillary propagation of a covered work occurring
solely as a consequence of using peer-to-peer transmission to receive a
copy likewise does not require acceptance. However, nothing other
than this License grants you permission to propagate or modify any
covered work. These actions infringe copyright if you do not accept this
License. Therefore, by modifying or propagating a covered work, you
indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically
receives a license from the original licensors, to run, modify and
propagate that work, subject to this License. You are not responsible for
enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an
organization, or substantially all assets of one, or subdividing an
organization, or merging organizations. If propagation of a covered work
results from an entity transaction, each party to that transaction who
receives a copy of the work also receives whatever licenses to the work
the party’s predecessor in interest had or could give under the previous
paragraph, plus a right to possession of the Corresponding Source of
the work from the predecessor in interest, if the predecessor has it or
can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights
granted or affirmed under this License. For example, you may not
impose a license fee, royalty, or other charge for exercise of rights
granted under this License, and you may not initiate litigation (including
a cross-claim or counterclaim in a lawsuit) alleging that any patent claim
is infringed by making, using, selling, offering for sale, or importing the
Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this
License of the Program or a work on which the Program is based. The
work thus licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or
controlled by the contributor, whether already acquired or hereafter
acquired, that would be
infringed by some manner, permitted by this
License, of making, using, or selling its contributor version, but do not
include claims that would be infringed only as a consequence of further
modification of the contributor version. For purposes of this definition,
“control” includes the right to grant patent sublicenses in a manner
consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free
patent license under the contributor’s essential patent claims, to make,
use, sell, offer for sale, import and otherwise run, modify and propagate
the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express
agreement or commitment, however denominated, not to enforce a
patent (such as an express permission to practice a patent or covenant
not to sue for patent infringement). To “grant” such a patent license to a
party means to make such an agreement or commitment not to enforce
a patent against the party.
If you convey a covered work, knowin
gly relying on a patent license, and
the Corresponding Source of the work is not available for anyone to copy,
free of charge and under the terms of this License, through a publicly
available network server or other readily accessible means, then you must
either (1) cause the Corresponding Source to be so available, or (2)
arrange to deprive yourself of the benefit of the patent license for this
particular work, or (3) arrange, in a manner consistent with the
requirements of this License, to extend the patent license to downstream
recipients. “Knowingly relying” means you have actual knowledge that, but
for the patent license, your conveying the covered work in a country, or
your recipient’s use of the covered work in a country, would infringe one or
more identifiable patents in that country that you have reason to believe
are valid.
If, pursuant to or in connection with a single transaction or arrangement,
you convey, or propagate by procuring conveyance of, a covered work,
and grant a patent license to some of the parties receiving the covered
work authorizing them to use, propagate, modify or convey a specific
copy of the covered work, then the patent license you grant is
automatically extended to all recipients of the covered work and works
based on it.
A patent license is “discriminatory” if it does not include within the scope
of its coverage, prohibits the exercise of, or is conditioned on the
non-exercise of one or more of the rights that are specifically granted
under this License. You may not convey a covered work if you are a
party to an arrangement with a third party that is in the business of
distributing software, under which you make payment to the third party
based on the extent of yo
ur activity of conveying the work, and under
which the third party grants, to any of the parties who would receive the
covered work from you, a discriminatory patent license (a) in connection
with copies of the covered work conveyed by you (or copies made from
those copies), or (b) primarily for and in connection with specific
products or c
ompilations that contain the covered work, unless you
entered into that arrangement, or that patent license was granted, prior
to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any
implied license or other defenses to infringement that may otherwise be
available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot convey a
covered work so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you
may not convey it at all. For example, if you agree to terms that obligate
you to collect a royalty for further conveying from those to whom you
convey the Program, the only way you could satisfy both those terms
and this License would be to refrain entirely from conveying the
Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have
permission to link or combine any covered work with a work licensed
under version 3 of the GNU Affero General Public License into a single
combined work, and to convey the resulting work. The terms of this
License will continue to apply to the part which is the covered work, but
the special requirements of the GNU Affero General Public License,
section 13, concerning interaction through a network will apply to the
combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions
of the GNU General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies that a certain numbered version of the GNU General Public
License “or any later version” applies to it, you have the option of
following the terms and conditions either of that numbered version or of
any later version published by the Free Software Foundation. If the
Program does not specify a version number of the GNU General Public
License, you may choose any version ever published by the Free
Software Foundation.
If the Program specifies that a proxy can decide which future versions of
the GNU General Public License can be used, that proxy’s public
statement of acceptance of a version permanently authorizes you to
choose that version for the Program.
Later license versions may give you additional or different permissions.
However, no additional obligations are imposed on any author or
copyright holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above
cannot be given local legal effect according to their terms, reviewing
courts shall apply local law that most closely approximates an absolute
waiver of all civil liability in connection with the Program, unless a
warranty or assumption of liability accompanies a copy of the Program
in return for a fee.
END OF TERMS AND CONDITIONS
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this
license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL.
It also counts as the successor of the GNU Library Public License,
version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom
to share and change it. By contrast, the GNU General Public Licenses
are intended to guarantee your freedom to share and change free
software to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some
specially designated software packages--typically libraries--of the Free
Software Foundation and other authors who decide to use it. You can
use it too, but we suggest you first think carefully about whether this
license or the ordinary General Public License is the better strategy to
use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not
price. Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for
this service if you wish); that you receive source code or can get it if you
want it; that you can change the software and use pieces of it in new
free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid
distributors to deny you these rights or to ask you to surrender these
rights. These restrictions translate to certain responsibilities for you if you
distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a
fee, you must give the recipients all the rights that we gave you. You
must make sure that they, too, receive or can get the source code. If
you link other code with the library, you must provide complete object
files to the recipients, so that they can relink them with the library after
making changes to the library and recompiling it. And you must show
them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the
library, and (2) we offer you this license, which gives you legal
permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no
warranty for the free library. Also, if the library is modified by someone
else and passed on, the recipients should know that what they have is
not the original version, so that the original author’s reputation will not be
affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any
free program. We wish to make sure that a company cannot effectively
restrict the users of a free program by obtaining a restrictive license from
a patent holder. Therefore, we insist that any patent license obtained for
a version of the library must be consistent with the full freedom of use
specified in this license.
Most GNU software, including some libraries, is covered by the ordinary
GNU General Public License. This license, the GNU Lesser General
Public License, applies to certain designated libraries, and is quite
different from the ordinary General Public License. We use this license
for certain libraries in order to permit linking those libraries into non-free
programs.
When a program is linked with a library, whether statically or using a
shared library, the combination of the two is legally speaking a
combined work, a derivative of the original library. The ordinary General
Public License therefore permits such linking only if the entire
combination fits its criteria of freedom. The Lesser General Public
License permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does
Less to protect the user’s freedom than the ordinary General Public
License. It also provides other free software developers Less of an
advantage over competing non-free programs. These disadvantages
are the reason we use the ordinary General Public License for many
libraries. However, the Lesser license provides advantages in certain
special circumstances.
For example, on rare occasions, there may be a special need to
encourage the widest possible use of a certain library, so that it
becomes a de-facto standard. To achieve this, non-free programs must
be allowed to use the library. A more frequent case is that a free library
does the same job as widely used non-free libraries. In this case, there
is little to gain by limiting the free library to free software only, so we use
the Lesser General Public License.
In other cases, permission to use a particular library in non-free
programs enables a greater number of people to use a large body of
free software. For example, permission to use the GNU C Library in
non-free programs enables many more people to use the whole GNU
operating system, as well as its variant, the GNU/Linux operating
system.
Although the Lesser General Public License is Less protective of the
users’ freedom, it does ensure that the user of a program that is linked
with the Library has the freedom and the wherewithal to run that
program using a modified version of the Library.
The precise terms and conditions for copying, distribution and
modification follow. Pay close attention to the difference between a
“work based on the library” and a “work that uses the library”. The
former contains code derived from the library, whereas the latter must
be combined with the library in order to run.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other
program which contains a notice placed by the copyright holder or
other authorized party saying it may be distributed under the terms of
this Lesser General Public License (also called “this License”). Each
licensee is addressed as “you”.
A “library” means a collection of software functions and/or data
prepared so as to be conveniently linked with application programs
(which use some of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which
has been distributed under these terms. A “work based on the Library”
means either the Library or any derivative work under copyright law: that
is to say, a work containing the Library or a portion of it, either verbatim
or with modifications and/or translated straightforwardly into another
language. (Hereinafter, translation is included without limitation in the
term “modification”.)
“Source code” for a work means the preferred form of the work for
making modifications to it. For a library, complete source code means
all the source code for all modules it contains, plus any associated
interface definition files, plus the scripts used to control compilation and
installation of the library.
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of running a
program using the Library is not restricted, and output from such a
program is covered only if its contents constitute a work based on the
Library (independent of the use of the Library in a tool for writing it).
Whether that is true depends on what the Library does and what the
program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library’s
complete source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy an
appropriate copyright notice and disclaimer of warranty; keep intact all
the notices that refer to this License and to the absence of any
warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of
it, thus forming a work based on the Library, and copy and distribute
such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices
stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no charge
to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a table of
data to be supplied by an application program that uses the
facility, other than as an argument passed when the facility is
invoked, then you must make a good faith effort to ensure that, in
the event an application does not supply such function or table,
the facility still operates, and performs whatever part of its purpose
remains meaningful.
(For example, a function in a library to compute square roots has a
purpose that is entirely well-defined independent of the application.
Therefore, Subsection 2d requires that any application-supplied function
or table used by this function must be optional: if the application does
not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Library, and can be
reasonably considered independent and separate works in themselves,
then this License, and its terms, do not apply to those sections when
you distribute them as separate works. But when you distribute the
same sections as part of a whole which is a work based on the Library,
the distribution of the whole must be on the terms of this License,
whose permissions for other licensees extend to the entire whole, and
thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your
rights to work written entirely by you; rather, the intent is to exercise the
right to control the distribution of derivative or collective works based on
the Library.
In addition, mere aggregation of another work not based on the Library
with the Library (or with a work based on the Library) on a volume of a
storage or distribution medium does not bring the other work under the
scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public
License instead of this License to a given copy of the Library. To do this,
you must alter all the notices that refer to this License, so that they refer
to the ordinary GNU General Public License, version 2, instead of to this
License. (If a newer version than version 2 of the ordinary GNU General
Public License has appeared, then you can specify that version instead
if you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy,
so the ordinary GNU General Public License applies to all subsequent
copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the
Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of
it, under Section 2) in object code or executable form under the terms
of Sections 1 and 2 above provided that you accompany it with the
complete corresponding machine-readable source code, which must
be distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange.
If distribution of object code is made by offering access to copy from a
designated place, then offering equivalent access to copy the source
code from the same place satisfies the requirement to distribute the
source code, even though third parties are not compelled to copy the
source along with the object code.
5. A program that contains no derivative of any portion of the Library,
but is designed to work with the Library by being compiled or linked
with it, is called a “work that uses the Library”. Such a work, in isolation,
is not a derivative work of the Library, and therefore falls outside the
scope of this License.
However, linking a “work that uses the Library” with the Library creates
an executable that is a derivative of the Library (because it contains
portions of the Library), rather than a “work that uses the library”. The
executable is therefore covered by this License. Section 6 states terms
for distribution of such executables.
When a “work that uses the Library” uses material from a header file
that is part of the Library, the object code for the work may be a
derivative work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked
without the Library, or if the work is itself a library. The threshold for this
to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure
layouts and accessors, and small macros and small inline functions (ten
lines or less in length), then the use of the object file is unrestricted,
regardless of whether it is legally a derivative work. (Executables
containing this object code plus portions of the Library will still fall under
Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute
the object code for the work under the terms of Section 6. Any
executables containing that work also fall under Section 6, whether or
not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link
a “work that uses the Library” with the Library to produce a work
containing portions of the Library, and distribute that work under terms
of your choice, provided that the terms permit modification of the work
for the customer’s own use and reverse engineering for debugging such
modifications.
You must give prominent notice with each copy of the work that the
Library is used in it and that the Library and its use are covered by this
License. You must supply a copy of this License. If the work during
execution displays copyright notices, you must include the copyright
notice for the Library among them, as well as a reference directing the
user to the copy of this License. Also, you must do one of these things:
a) Accompany the work with the complete corresponding machine-
readable source code for the Library including whatever changes
were used in the work (which must be distributed under Sections
1 and 2 above); and, if the work is an executable linked with the
Library, with the complete machine readable “work that uses the
Library”, as object code and/or source code, so that the user can
modify the Library and then relink to produce a modified
executable containing the modified Library. (It is understood that
the user who changes the contents of definitions files in the Library
will not necessarily be able to recompile the application to use the
modified definitions.)
b)
Use a suitable shared library mechanism for linking with the Library.
A suitable mechanism is one that (1) uses at run time a copy of the
library already present on the user’s computer system, rather than
copying library functions into the executable, and (2) will operate
properly with a modified version of the library, if the user installs
one, as long as the modified version is interface-compatible with
the version that the work was made with.
c) Accompany the work with a written offer, valid for at least three
years, to give the same user the materials specified in Subsection
6a, above, for a charge no more than the cost of performing this
distribution.
d) If distribution of the work is made by offering access to copy from
a designated place, offer equivalent access to copy the above
specified materials from the same place.
e) Verify that the user has already received a copy of these materials
or that you have already sent this user a copy.
For an executable, the required form of the “work that uses the Library”
must include any data and utility programs needed for reproducing the
executable from it. However, as a special exception, the materials to be
distributed need not include anything that is normally distributed (in
either source or binary form) with the major components (compiler,
kernel, and so on) of the operating system on which the executable
runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions
of other proprietary libraries that do not normally accompany the
operating system. Such a contradiction means you cannot use both
them and the Library together in an executable that you distribute.
7. You may place library facilities that are a work based on the Library
side-by-side in a single library together with other library facilities not
covered by this License, and distribute such a combined library,
provided that the separate distribution of the work based on the Library
and of the other library facilities is otherwise permitted, and provided
that you do these two things:
a) Accompany the combined library with a copy of the same work
based on the Library, uncombined with any other library facilities.
This must be distributed under the terms of the Sections above.
b)
Give prominent notice with the combined library of the fact that part
of it is a work based on the Library, and explaining where to find the
accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the
Library except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense, link with, or distribute the Library
is void, and will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from you under
this License will not have their licenses terminated so long as such
parties remain in full compliance.
9.
You are not required to accept this License, since you have not signed
it. However, nothing else gr
ants you permission to modify or distribute
the Library or its derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying or distributing
the Library (or any work based on the Library), you indicate your
acceptance of this License to do so, and all its terms and conditions for
copying, distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the
Library), the recipient automatically receives a license from the original
licensor to copy, distribute, link with or modify the Library subject to
these terms and conditions. You may not impose any further restrictions
on the recipients’ exercise of the rights granted herein. You are not
responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot distribute
so as to satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you may not
distribute the Library at all. For example, if a patent license would not
permit royalty free redistribution of the Library by all those who receive
copies directly or indirectly through you, then the only way you could
satisfy both it and this License would be to refrain entirely from
distribution of the Library.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply, and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or
other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software
distribution system which is implemented by public license practices. Many
people have made generous contributions to the wide range of software
distributed through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing to
distribute software through any other system and a licensee cannot impose
that choice.
This section is intended to make thoroughly clear what is believed to be
a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Library under this License may add an
explicit geographical distribution limitation excluding those countries, so
that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if
written in the body of this License.
13. The Free Software Foundation may publish revised and/or new
versions of the Lesser General Public License from time to time. Such
new versions will be similar in spirit to the present version, but may differ
in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library
specifies a version number of this License which applies to it and “any
later version”, you have the option of following the terms and conditions
either of that version or of any later version published by the Free
Software Foundation. If the Library does not specify a license version
number, you may choose any version ever published by the Free
Software Foundation.
14. If you wish to incorporate parts of the Library into other free
programs whose distribution conditions are incompatible with these,
write to the author to ask for permission. For software which is
copyrighted by the Free Software Foundation, write to the Free
Software Foundation; we sometimes make exceptions for this. Our
decision will be guided by the two goals of preserving the free status of
all derivatives of our free software and of promoting the sharing and
reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE
IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED
BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN
WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU.
SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest
possible use to the public, we recommend making it free software that
everyone can redistribute and change. You can do so by permitting
redistribution under these terms (or, alternatively, under the terms of the
ordinary General Public License).
To apply these terms, attach the following notices to the library. It is
safest to attach them to the start of each source file to most effectively
convey the exclusion of warranty; and each file should have at least the
“copyright” line and a pointer to where the full notice is found. one line
to give the library’s name and an idea of what it does.
Copyright (C) year name of author
This library is free software; you can redistribute it and/or modify it under
the terms of the GNU Lesser General Public License as published by
the Free Software Foundation; either version 2.1 of the License, or (at
your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-
1301 USA Also add information on how to contact you by electronic
and paper mail.
You should also get your employer (if you work as a programmer) or
your school, if any, to sign a “copyright disclaimer” for the library, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library
‘Frob’ (a library for tweaking knobs) written by James Random Hacker.
signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice.
OpenSSL LICENSE
Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software
must display the following acknowledgment: “This product includes
software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be
used to endorse or promote products derived from this software
without prior written permission. For written permission, please contact
openssl-core@openssl.org.
5. Products derived from this software may not be called “OpenSSL”
nor may “OpenSSL” appear in their names without prior written
permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following
acknowledgment: “This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.
org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ‘‘AS IS’’
AND ANY EXPRESSED OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.This product includes cryptographic software written by Eric
Young (eay@cryptsoft.com). This product includes software written by
Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights
reserved. This package is an SSL implementation written by Eric Young
(eay@cryptsoft.com). The implementation was written so as to conform
with Netscapes SSL. This library is free for commercial and non-
commercial use as long as the following conditions are aheared to. The
following conditions apply to all code found in this distribution, be it the
RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL
documentation included with this distribution is covered by the same
copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.
com).
Copyright remains Eric Young’s, and as such any Copyright notices in
the code are not to be removed.
If this package is used in a product, Eric Young should be given
attribution as the author of the parts of the library used. This can be in
the form of a textual message at program startup or in documentation
(online or textual) provided with the package.Redistribution and use in
source and binary forms, with or without modification, are permitted
provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this
list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution. 3.
All advertising materials mentioning features or use of this software must
display the following acknowledgement: “This product includes
cryptographic software written by Eric Young (eay@cryptsoft.com)” The
word ‘cryptographic’ can be left out if the rouines from the library being
used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative thereof) from
the apps directory (application code) you must include an
acknowledgement: “This product includes software written by Tim
Hudson (tjh@cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ‘‘AS IS’’ AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.The licence and distribution terms for any publically
available version or derivative of this code cannot be changed. i.e. this
code cannot simply be copied and put under another distribution
licence [including the GNU Public Licence.
Boost Software License
Boost Software License - Version 1.0 - August 17th, 2003 Permission is
hereby granted, free of charge, to any person or organization obtaining
a copy of the software and accompanying documentation covered by
this license (the “Software”) to use, reproduce, display, distribute,
execute, and transmit the Software, and to prepare derivative works of
the Software, and to permit third-parties to whom the Software is
furnished to do so, all subject to the following : The copyright notices in
the Software and this entire statement, including the above license
grant, this restriction and the following disclaimer, must be included in all
copies of the Software, in whole or in part, and all derivative works of
the Software, unless such copies or derivative works are solely in the
form of machine-executable object code generated by a source
language processor.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF
ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT. IN NO
EVENT SHALL THE COPYRIGHT HOLDERS OR ANYONE
DISTRIBUTING THE SOFTWARE BE LIABLE FOR ANY DAMAGES OR
OTHER LIABILITY, WHETHER IN CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE
OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
COMMON DEVELOPMENT AND DISTRIBUTION
LICENSE Version 1.0
1. Definitions.
1.1. “Contributor” means each individual or entity that creates or
contributes to the creation of Modifications.
1.2. “Contributor Version” means the combination of the Original
Software, prior Modifications used by a Contributor (if any), and the
Modifications made by that particular Contributor.
1.3. “Covered Software” means (a) the Original Software, or (b)
Modifications, or (c) the combination of files containing Original Software
with files containing Modifications, in each case including portions
thereof.
1.4. “Executable” means the Covered Software in any form other than
Source Code.
1.5. “Initial Developer” means the individual or entity that first makes
Original Software available under this License.
1.6. “Larger Work” means a work which combines Covered Software or
portions thereof with code not governed by the terms of this License.
1.7. “License” means this document.
1.8. “Licensable” means having the right to grant, to the maximum
extent possible, whether at the time of the initial grant or subsequently
acquired, any and all of the rights conveyed herein.
1.9. “Modifications” means the Source Code and Executable form of
any of the following:
A. Any file that results from an addition to, deletion from or
modification of the contents of a file containing Original Software
or previous Modifications;
B. Any new file that contains any part of the Original Software or
previous Modifications; or
C. Any new file that is contributed or otherwise made available under
the terms of this License.
1.10. “Original Software” means the Source Code and Executable form
of computer software code that is originally released under this License.
1.11. “Patent Claims” means any patent claim(s), now owned or
hereafter acquired, including without limitation, method, process, and
apparatus claims, in any patent Licensable by grantor.
1.12. “Source Code” means (a) the common form of computer software
code in which modifications are made and (b) associated
documentation included in or with such code.
1.13. “You” (or “Your”) means an individual or a legal entity exercising
rights under, and complying with all of the terms of, this License. For
legal entities, “You” includes any entity which controls, is controlled by,
or is under common control with You. For purposes of this definition,
“control” means (a) the power, direct or indirect, to cause the direction
or management of such entity, whether by contract or otherwise, or (b)
ownership of more than fifty percent (50%) of the outstanding shares or
beneficial ownership of such entity.
2. License Grants.
2.1. The Initial Developer Grant.
Conditioned upon Your compliance with Section 3.1 below and subject
to third party intellectual property claims, the Initial Developer hereby
grants You a world-wide, royalty-free, non-exclusive license:
a) under intellectual property rights (other than patent or trademark)
Licensable by Initial Developer, to use, reproduce, modify, display,
perform, sublicense and distribute the Original Software (or
portions thereof), with or without Modifications, and/or as part of a
Larger Work; and
b) under Patent Claims infringed by the making, using or selling of
Original Software, to make, have made, use, practice, sell, and
offer for sale, and/or otherwise dispose of the Original Software (or
portions thereof).
c) The licenses granted in Sections 2.1(a) and (b) are effective on the
date Initial Developer first distributes or otherwise makes the
Original Software available to a third party under the terms of this
License.
d) Notwithstanding Section 2.1(b) above, no patent license is
granted: (1) for code that You delete from the Original Software, or
(2) for infringements caused by: (i) the modification of the Original
Software, or (ii) the combination of the Original Software with other
software or devices.
2.2. Contributor Grant.
Conditioned upon Your compliance with Section 3.1 below and subject
to third party intellectual property claims, each Contributor hereby
grants You a world-wide, royalty-free, non-exclusive license:
a) under intellectual property rights (other than patent or trademark)
Licensable by Contributor to use, reproduce, modify, display,
perform, sublicense and distribute the Modifications created by
such Contributor (or portions thereof), either on an unmodified
basis, with other Modifications, as Covered Software and/or as
part of a Larger Work; and
b) under Patent Claims infringed by the making, using, or selling of
Modifications made by that Contributor either alone and/or in
combination with its Contributor Version (or portions of such
combination), to make, use, sell, offer for sale, have made, and/or
otherwise dispose of: (1) Modifications made by that Contributor
(or portions thereof); and (2) the combination of Modifications
made by that Contributor with its Contributor Version (or portions
of such combination).
c) The licenses granted in Sections 2.2(a) and 2.2(b) are effective on
the date Contributor first distributes or otherwise makes the
Modifications available to a third party.
d) Notwithstanding Section 2.2(b) above, no patent license is
granted: (1) for any code that Contributor has deleted from the
Contributor Version; (2) for infringements caused by: (i) third party
modifications of Contributor Version, or (ii) the combination of
Modifications made by that Contributor with other software
(except as part of the Contributor Version) or other devices; or (3)
under Patent Claims infringed by Covered Software in the absence
of Modifications made by that Contributor.
3. Distribution Obligations.
3.1. Availability of Source Code.
Any Covered Software that You distribute or otherwise make available in
Executable form must also be made available in Source Code form and
that Source Code form must be distributed only under the terms of this
License. You must include a copy of this License with every copy of the
Source Code form of the Covered Software You distribute or otherwise
make available. You must inform recipients of any such Covered
Software in Executable form as to how they can obtain such Covered
Software in Source Code form in a reasonable manner on or through a
medium customarily used for software exchange.
3.2. Modifications.
The Modifications that You create or to which You contribute are
governed by the terms of this License. You represent that You believe
Your Modifications are Your original creation(s) and/or You have
sufficient rights to grant the rights conveyed by this License.
3.3. Required Notices.
You must include a notice in each of Your Modifications that identifies
You as the Contributor of the Modification. You may not remove or alter
any copyright, patent or trademark notices contained within the
Covered Software, or any notices of licensing or any descriptive text
giving attribution to any Contributor or the Initial Developer.
3.4. Application of Additional Terms.
You may not offer or impose any terms on any Covered Software in
Source Code form that alters or restricts the applicable version of this
License or the recipients’ rights hereunder. You may choose to offer,
and to charge a fee for, warranty, support, indemnity or liability
obligations to one or more recipients of Covered Software. However,
you may do so only on Your own behalf, and not on behalf of the Initial
Developer or any Contributor. You must make it absolutely clear that any
such warranty, support, indemnity or liability obligation is offered by You
alone, and You hereby agree to indemnify the Initial Developer and every
Contributor for any liability incurred by the Initial Developer or such
Contributor as a result of warranty, support, indemnity or liability terms
You offer.
3.5. Distribution of Executable Versions.
You may distribute the Executable form of the Covered Software under
the terms of this License or under the terms of a license of Your choice,
which may contain terms different from this License, provided that You
are in compliance with the terms of this License and that the license for
the Executable form does not attempt to limit or alter the recipient’s
rights in the Source Code form from the rights set forth in this License. If
You distribute the Covered Software in Executable form under a different
license, You must make it absolutely clear that any terms which differ
from this License are offered by You alone, not by the Initial Developer or
Contributor. You hereby agree to indemnify the Initial Developer and
every Contributor for any liability incurred by the Initial Developer or such
Contributor as a result of any such terms You offer.
3.6. Larger Works.
You may create a Larger Work by combining Covered Software with
other code not governed by the terms of this License and distribute the
Larger Work as a single product. In such a case, You must make sure
the requirements of this License are fulfilled for the Covered Software.
4. Versions of the License.
4.1. New Versions.
Sun Microsystems, Inc. is the initial license steward and may publish
revised and/or new versions of this License from time to time. Each
version will be given a distinguishing version number. Except as
provided in Section 4.3, no one other than the license steward has the
right to modify this License.
4.2. Effect of New Versions.
You may always continue to use, distribute or otherwise make the
Covered Software available under the terms of the version of the
License under which You originally received the Covered Software. If the
Initial Developer includes a notice in the Original Software prohibiting it
from being distributed or otherwise made available under any
subsequent version of the License, You must distribute and make the
Covered Software available under the terms of the version of the
License under which You originally received the Covered Software.
Otherwise, You may also choose to use, distribute or otherwise make
the Covered Software available under the terms of any subsequent
version of the License published by the license steward.
4.3. Modified Versions.
When You are an Initial Developer and You want to create a new license
for Your Original Software, You may create and use a modified version
of this License if You: (a) rename the license and remove any references
to the name of the license steward (except to note that the license
differs from this License); and (b) otherwise make it clear that the license
contains terms which differ from this License.
5. DISCLAIMER OF WARRANTY.
COVERED SOFTWARE IS PROVIDED UNDER THIS LICENSE ON AN
“AS IS” BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
WARRANTIES THAT THE COVERED SOFTWARE IS FREE OF
DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR
NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE COVERED SOFTWARE IS WITH YOU.
SHOULD ANY COVERED SOFTWARE PROVE DEFECTIVE IN ANY
RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER
CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY
SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER OF
WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE.
NO USE OF ANY COVERED SOFTWARE IS AUTHORIZED
HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
6. TERMINATION.
6.1. This License and the rights granted hereunder will terminate
automatically if You fail to comply with terms herein and fail to cure such
breach within 30 days of becoming aware of the breach. Provisions
which, by their nature, must remain in effect beyond the termination of
this License shall survive.
6.2. If You assert a patent infringement claim (excluding declaratory
judgment actions) against Initial Developer or a Contributor (the Initial
Developer or Contributor against whom You assert such claim is
referred to as “Participant”) alleging that the Participant Software
(meaning the Contributor Version where the Participant is a Contributor
or the Original Software where the Participant is the Initial Developer)
directly or indirectly infringes any patent, then any and all rights granted
directly or indirectly to You by such Participant, the Initial Developer (if
the Initial Developer is not the Participant) and all Contributors under
Sections 2.1 and/or 2.2 of this License shall, upon 60 days notice from
Participant terminate prospectively and automatically at the expiration of
such 60 day notice period, unless if within such 60 day period You
withdraw Your claim with respect to the Participant Software against
such Participant either unilaterally or pursuant to a written agreement
with Participant.
6.3. In the event of termination under Sections 6.1 or 6.2 above, all end
user licenses that have been validly granted by You or any distributor
hereunder prior to termination (excluding licenses granted to You by any
distributor) shall survive termination.
7. LIMITATION OF LIABILITY.
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY,
WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR
OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER
CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED SOFTWARE,
OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY
PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING,
WITHOUT LIMITATION, DAMAGES FOR LOST PROFITS, LOSS OF
GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR
MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES
OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED
OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF
LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR
PERSONAL INJURY RESULTING FROM SUCH PARTY’S
NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH
LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY
TO YOU.
8. U.S. GOVERNMENT END USERS.
The Covered Software is a “commercial item,” as that term is defined in
48 C.F.R. 2.101 (Oct. 1995), consisting of “commercial computer
software” (as that term is defined at 48 C.F.R. 252.227-7014(a)(1)) and
“commercial computer software documentation” as such terms are
used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R.
12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all
U.S. Government End Users acquire Covered Software with only those
rights set forth herein. This U.S. Government Rights clause is in lieu of,
and supersedes, any other FAR, DFAR, or other clause or provision that
addresses Government rights in computer software under this License.
9. MISCELLANEOUS.
This License represents the complete agreement concerning subject
matter hereof. If any provision of this License is held to be
unenforceable, such provision shall be reformed only to the extent
necessary to make it enforceable. This License shall be governed by the
law of the jurisdiction specified in a notice contained within the Original
Software (except to the extent applicable law, if any, provides
otherwise), excluding such jurisdiction’s conflict-of-law provisions. Any
litigation relating to this License shall be subject to the jurisdiction of the
courts located in the jurisdiction and venue specified in a notice
contained within the Original Software, with the losing party responsible
for costs, including, without limitation, court costs and reasonable
attorneys’ fees and expenses. The application of the United Nations
Convention on Contracts for the International Sale of Goods is expressly
excluded. Any law or regulation which provides that the language of a
contract shall be construed against the drafter shall not apply to this
License. You agree that You alone are responsible for compliance with
the United States export administration regulations (and the export
control laws and regulation of any other countries) when You use,
distribute or otherwise make available any Covered Software.
10. RESPONSIBILITY FOR CLAIMS.
As between Initial Developer and the Contributors, each party is
responsible for claims and damages arising, directly or indirectly, out of
its utilization of rights under this License and You agree to work with
Initial Developer and Contributors to distribute such responsibility on an
equitable basis. Nothing herein is intended or shall be deemed to
constitute any admission of liability.
--------------------------------------------------------------------
NOTICE PURSUANT TO SECTION 9 OF THE COMMON
DEVELOPMENT AND DISTRIBUTION LICENSE (CDDL)
For Covered Software in this distribution, this License shall be governed
by the laws of Germany (excluding conflict-of-law provisions).
Any litigation relating to this License shall be subject to the jurisdiction
and the courts of Berlin Germany, with venue lying in Berlin Germany.
The FreeType Project LICENSE
----------------------------
2002-Apr-11
Copyright 1996-2002 by
David Turner, Robert Wilhelm, and Werner Lemberg
Introduction
============
The FreeType Project is distributed in several archive packages; some of
them may contain, in addition to the FreeType font engine, various tools
and contributions which rely on, or relate to, the FreeType Project.
This license applies to all files found in such packages, and which do
not fall under their own explicit license. The license affects thus the
FreeType font engine, the test programs, documentation and makefiles,
at the very least.
This license was inspired by the BSD, Artistic, and IJG (Independent
JPEG Group) licenses, which all encourage inclusion and use of free
software in commercial and freeware products alike. As a consequence,
its main points are that:
• We don’t promise that this software works. However, we will be
interested in any kind of bug reports. (`as is’ distribution)
• You can use this software for whatever you want, in parts or full form,
without having to pay us. (`royalty-free’ usage)
• You may not pretend that you wrote this software. If you use it, or
only parts of it, in a program, you must acknowledge somewhere in
your documentation that you have used the FreeType code. (`credits’)
We specifically permit and encourage the inclusion of this software, with
or without modifications, in commercial products. We disclaim all
warranties covering The FreeType Project and assume no liability related
to The FreeType Project.
Finally, many people asked us for a preferred form for a credit/disclaimer
to use in compliance with this license. We thus encourage you to use
the following text:
“Portions of this software are copyright © 1996-2002 The FreeType
Project (www.freetype.org). All rights reserved.”
Legal Terms
===========
1. Definitions
--------------
Throughout this license, the terms `package’, `FreeType Project’, and
`FreeType archive’ refer to the set of files originally distributed by the
authors (David Turner, Robert Wilhelm, and Werner Lemberg) as the
`FreeType Project’, be they named as alpha, beta or final release.
`You’ refers to the licensee, or person using the project, where `using’ is
a generic term including compiling the project’s source code as well as
linking it to form a `program’ or `executable’. This program is referred to
as `a program using the FreeType engine’.
This license applies to all files distributed in the original FreeType Project,
including all source code, binaries and documentation, unless otherwise
stated in the file in its original, unmodified form as distributed in the
original archive. If you are unsure whether or not a particular file is
covered by this license, you must contact us to verify this.
The FreeType Project is copyright (C) 1996-2000 by David Turner,
Robert Wilhelm, and Werner Lemberg. All rights reserved except as
specified below.
2. No Warranty
--------------
THE FREETYPE PROJECT IS PROVIDED `AS IS’ WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED
BY THE USE OR THE INABILITY TO USE, OF THE FREETYPE PROJECT.
3. Redistribution
-----------------
This license grants a worldwide, royalty-free, perpetual and irrevocable
right and license to use, execute, perform, compile, display, copy, create
derivative works of, distribute and sublicense the FreeType Project (in
both source and object code forms) and derivative works thereof for any
purpose; and to authorize others to exercise some or all of the rights
granted herein, subject to the following conditions:
o Redistribution of source code must retain this license file (`FTL.TXT’)
unaltered; any additions, deletions or changes to the original files must
be clearly indicated in accompanying documentation. The copyright
notices of the unaltered, original files must be preserved in all copies
of source files.
o Redistribution in binary form must provide a disclaimer that states that
the software is based in part of the work of the FreeType Team, in the
distribution documentation. We also encourage you to put an URL to
the FreeType web page in your documentation, though this isn’t
mandatory.
These conditions apply to any software derived from or based on the
FreeType Project, not just the unmodified files. If you use our work, you
must acknowledge us. However, no fee need be paid to us.
4. Advertising
--------------
Neither the FreeType authors and contributors nor you shall use the
name of the other for commercial, advertising, or promotional purposes
without specific prior written permission.
We suggest, but do not require, that you use one or more of the
following phrases to refer to this software in your documentation or
advertising materials: `FreeType Project’, `FreeType Engine’, `FreeType
library’, or `FreeType Distribution’.
As you have not signed this license, you are not required to accept it.
However, as the FreeType Project is copyrighted material, only this
license, or another one contracted with the authors, grants you the right
to use, distribute, and modify it. Therefore, by using, distributing, or
modifying the FreeType Project, you indicate that you understand and
accept all the terms of this license.
5. Contacts
-----------
There are two mailing lists related to FreeType:
o freetype@freetype.org
Discusses general use and applications of FreeType, as well as future
and wanted additions to the library and distribution. If you are looking for
support, start in this list if you haven’t found anything to help you in the
documentation.
o devel@freetype.org
Discusses bugs, as well as engine internals, design issues, specific
licenses, porting, etc.
o http://www.freetype.org
Holds the current FreeType web page, which will allow you to download
our latest development version and read online documentation.
You can also contact us individually at: David Turner {david.turner@
freetype.org} Robert Wilhelm {robert.wilhelm@freetype.org} Werner
Lemberg {werner.lemberg@freetype.org}
RSA MD4 or MD5 Message-Digest Algorithm
License
Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All rights
reserved.
License to copy and use this software is granted provided that it is
identified as the “RSA Data Security, Inc. MD5 Message-Digest
Algorithm” in all material mentioning or referencing this software or this
function.
License is also granted to make and use derivative works provided that
such works are identified as “derived from the RSA Data Security, Inc.
MD5 Message-Digest Algorithm” in all material mentioning or
referencing the derived work.
RSA Data Security, Inc. makes no representations concerning either the
merchantability of this software or the suitability of this software for any
particular purpose. It is provided “as is” without express or implied
warranty of any kind.
These notices must be retained in any copies of any part of this
documentation and/or software.
The MIT License
Copyright 2008 Jeffrey Powers for Fluxcapacity Open Source.
Copyright 2011, John Resig
Copyright 2005-2009 Sam Stephenson
Permission is hereby granted, free of charge, to any person obtaining a
copy of this software and associated documentation files (the
“Software”), to deal in the Software without restriction, including without
limitation the rights to use, copy, modify, merge, publish, distribute,
sublicense, and/or sell copies of the Software, and to permit persons to
whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included
in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF
ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT
SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE
OR OTHER DEALINGS IN THE SOFTWARE.
Its advanced feature-set (FastCGI, CGI, Auth, Output-Compression,
URL-Rewriting and many more) make lighttpd the perfect webserver-
software for every server that suffers load problems.
For more additional information, send email to help.cctv@hanwha.com.
Copyright (c) 2004, Kneschke, incremental
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met :
• Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
• Neither the name of the ‘incremental’ nor the names of its
contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Some software components of this product incorporate source code covered under the BSD license as follows.
Component Name License License URL
lighttpd 1.4.26 BSD 2.0 http://www.opensource.org/licenses/bsd-license.html
lighttpd is a secure, fast, compliant, and very flexible webserver that has been optimized for high-performance environments. It has a very low
memory footprint compared to other webservers and takes care of cpuload.
For more additional information, send email to help.cctv@hanwha.com.
Copyright (c) 1998-2000 University College London
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, is permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software
must display the following acknowledgement: This product includes
software developed by the Computer Science Department at
University College London
4. Neither the name of the University nor of the Department may be
used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHORS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE AUTHORS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Component Name License License URL
librtp 1.20 BSD 2.0 http://www.opensource.org/licenses/bsd-license.html
Simple Network Management Protocol (SNMP) is an Internetstandard
protocol for managing devices on IP networks. It is used mostly in
network management systems to monitor the devices attached to the
network for conditions that need administrative attention. Net-SNMP is a
suite of applications used to implement SNMP v1, SNMP v2c and
SNMP v3 using both IPv4 and IPv6.
For more additional information, send email to help.cctv@hanwha.com.
Various copyrights apply to this package, listed in various separate parts
below. Please make sure that you read all the parts.
Part 1: CMU/UCD copyright notice: (BSD like)
Copyright 1989, 1991, 1992 by Carnegie Mellon University
Derivative Work - 1996, 1998-2000
Copyright 1996, 1998-2000 The Regents of the University of California
All Rights Reserved
Permission to use, copy, modify and distribute this software and its
documentation for any purpose and without fee is hereby granted,
provided that the above copyright notice appears in all copies and that
both that copyright notice and this permission notice appear in
supporting documentation, and that the name of CMU and The
Regents of the University of California not be used in advertising or
publicity pertaining to distribution of the software without specific written
permission.
CMU AND THE REGENTS OF THE UNIVERSITY OF CALIFORNIA
DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE,
INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS. IN NO EVENT SHALL CMU OR THE REGENTS OF THE
UNIVERSITY OF CALIFORNIA BE LIABLE FOR ANY SPECIAL,
INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
WHATSOEVER RESULTING FROM THE LOSS OF USE, DATA OR
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE
OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF THIS
SOFTWARE.
Part 2: Networks Associates Technology, Inc
copyright notice (BSD)
Copyright (c) 2001-2003, Networks Associates Technology, Inc
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of the Networks Associates Technology, Inc nor the
names of its contributors may be used to endorse or promote
products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Part 3: Cambridge Broadband Ltd. copyright notice
(BSD)
Portions of this code are copyright (c) 2001-2003, Cambridge
Broadband Ltd.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. The name of Cambridge Broadband Ltd. may not be used to
endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS
IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Part 4: Sun Microsystems, Inc. copyright notice
(BSD)
Component Name License License URL
net-snmp-5.4.1 BSD http://www.net-snmp.org/about/license.html
Copyright © 2003 Sun Microsystems, Inc., 4150 Network Circle, Santa
Clara, California 95054, U.S.A.
All rights reserved.
Use is subject to license terms below. This distribution may include
materials developed by third parties. Sun, Sun Microsystems, the Sun
logo and Solaris are trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other countries. Redistribution and
use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of the Sun Microsystems, Inc. nor the names of its
contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Part 5: Sparta, Inc copyright notice (BSD)
Copyright (c) 2003-2009, Sparta, Inc
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of Sparta, Inc nor the names of its contributors may
be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Part 6: Cisco/BUPTNIC copyright notice (BSD)
Copyright (c) 2004, Cisco, Inc and Information Network Center of
Beijing University of Posts and Telecommunications.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of Cisco, Inc, Beijing University of Posts and
Telecommunications, nor the names of their contributors may be
used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Part 7: Fabasoft R&D Software GmbH & Co KG
copyright notice (BSD)
Copyright (c) Fabasoft R&D Software GmbH & Co KG, 2003
oss@fabasoft.com
Author: Bernhard Penz
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. The name of Fabasoft R&D Software GmbH & Co KG or any of its
subsidiaries, brand or product names may not be used to endorse or
promote products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS
IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Part 8: Apple Inc. copyright notice (BSD)
Copyright (c) 2007 Apple Inc.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of Apple Inc. (“Apple”) nor the names of its
contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY APPLE AND ITS CONTRIBUTORS
“AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL APPLE OR
ITSCONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Part 9: ScienceLogic, LLC copyright notice (BSD)
Copyright (c) 2009, ScienceLogic, LLC
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
aremet:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of ScienceLogic, LLC nor the names of its
contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
For more additional information, send email to help.cctv@hanwha.com.
Copyright (c) 2005-2009, Thomas BERNARD
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote
products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Component Name License License URL
miniupnpc 1.5 BSD 2.0 http://miniupnp.free.fr/
For more additional information, send email to help.cctv@hanwha.com.
Copyright (c) 2003 Paul Mackerras.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2.
The name(s) of the authors of this software must not be used to
endorse or promote products derived from this software without prior
written permission.
3.
Redistributions of any form whatsoever must retain the following
acknowledgment: “This product includes software developed by Paul
Mackerras <paulus@samba.org>”.
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 1995 Pedro Roque Marques.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1.
Redistributions of source code must retain the above copyright notice,
this list of conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3.
The names of the authors of this software must not be used to
endorse or promote products derived from this software without prior
written permission.
4.
Redistributions of any form whatsoever must retain the following
acknowledgment: “This product includes software developed by
Pedro Roque Marques <pedro_m@yahoo.com>”
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 1995 Eric Rosenquist.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1.
Redistributions of source code must retain the above copyright notice,
this list of conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3.
The name(s) of the authors of this software must not be used to
endorse or promote products derived from this software without prior
written permission.
Component Name License License URL
ppp 2.4.5 BSD 2.0 http://packages.debian.org/changelogs/pool/main/p/ppp/ppp_2.4.5-5.1/
ppp-udeb.copyright
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 2002 Google, Inc.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1.
Redistributions of source code must retain the above copyright notice,
this list of conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3.
The name(s) of the authors of this software must not be used to
endorse or promote products derived from this software without prior
written permission.
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 2001 by Sun Microsystems, Inc.
All rights reserved.
Non-exclusive rights to redistribute, modify, translate, and use this
software in source and binary forms, in whole or in part, is hereby
granted, provided that the above copyright notice is duplicated in any
source form, and that neither the name of the copyright holder nor the
author is used to endorse or promote products derived from this
software.
THIS SOFTWARE IS PROVIDED ``AS IS’’ AND WITHOUT ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE
IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
Copyright (c) 1999 Tommi Komulainen.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1.
Redistributions of source code must retain the above copyright notice,
this list of conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3.
The name(s) of the authors of this software must not be used to
endorse or promote products derived from this software without prior
written permission.
4.
Redistributions of any form whatsoever must retain the following
acknowledgment: “This product includes software developed by
Tommi Komulainen <Tommi.Komulainen@iki.fi>”.
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT
SHALL THE AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN
AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Copyright (c) 1984-2000 Carnegie Mellon University.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1.
Redistributions of source code must retain the above copyright notice,
this list of conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3.
The name “Carnegie Mellon University” must not be used to endorse
or promote products derived from this software without prior written
permission. For permission or any legal details, please contact Office
of Technology Transfer Carnegie Mellon University 5000 Forbes
Avenue Pittsburgh, PA 15213-3890 (412) 268-4387, fax: (412)
268-7395 tech-transfer@andrew.cmu.edu
4.
Redistributions of any form whatsoever must retain the following
acknowledgment: “This product includes software developed by
Computing Services at Carnegie Mellon University (http://www.cmu.
edu/computing/).”
CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES
WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT
SHALL CARNEGIE MELLON UNIVERSITY BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY
DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA
OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR
IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS
SOFTWARE.
Copyright (c) 2008 Mark Lord
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are
met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of the copyright holder nor the names of its
contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Component Name License License URL
hdparm-9.39 BSD-License http://www.opensource.org/licenses/bsd-license.html
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly
to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of
where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery
return system.
Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more
environmentally friendly products.
The Eco mark represents Hanwha Techwin’s devotion to creating environmentally friendly products, and indicates that the product
satisfies the EU RoHS Directive.
Head O ce
6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si,
Gyeonggi-do, 463-400 Rep. of KOREA
Tel : +82.70.7147.8753 Fax : +82.31.8018.3740
www.hanwha-security.com
Hanwha Techwin America
500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666
Toll Free +1.877.213.1222 Direct +1.201.325.6920
Fax +1.201.373.0124
www.hanwha-security.com
Hanwha Techwin Europe
Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom
Tel +44.1932.57.8100 Fax +44.1932.57.8101
www.hanwha-security.eu