Table of Contents
- Before Using the Product
- Preparations
- Connecting and Using a Source Device
- Before Connecting
- Connecting to a PC
- Connecting to a Video Device
- Connecting the HDBase-T
- Connecting to an Audio System
- Connecting the LAN Cable
- Changing the Input source (except the LH55OHFPSBC model)
- Web Browser (except the LH55OHFPSBC model)
- Changing the Input source (applies to the LH55OHFPSBC model only)
- Using MDC
- Player feature (except the LH55OHFPSBC model)
- Screen Adjustment (except the LH55OHFPSBC model)
- OnScreen Display (except the LH55OHFPSBC model)
- Network (except the LH55OHFPSBC model)
- System (except the LH55OHFPSBC model)
- Support (except the LH55OHFPSBC model)
- Player feature (applies to the LH55OHFPSBC model only)
- Screen Adjustment (applies to the LH55OHFPSBC model only)
- OnScreen Display (applies to the LH55OHFPSBC model only)
- Network (applies to the LH55OHFPSBC model only)
- System (applies to the LH55OHFPSBC model only)
- Support (applies to the LH55OHFPSBC model only)
- Troubleshooting Guide
- Specifications
- Appendix
Samsung LH46OHF2VBC/EN User Manual
Displayed below is the user manual for LH46OHF2VBC/EN by Samsung which is a product in the Signage Displays category. This manual has pages.
Related Manuals
USER MANUAL
OH46F I OH55F
The colour and the appearance may differ depending on the product, and the specifications are subject to change without prior
notice to improve the performance.
The contents of this manual are subject to change without notice to improve quality.
© Samsung
Samsung owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung is prohibited.
Trademarks other than that of Samsung are owned by their respective owners.
An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect (i.e., where the user manual has
not been read).
(b) You bring the unit to a repair centre, but it is found that the product has no defect (i.e., where the user manual has not
been read).
You will be informed of the administration fee amount before a technician visits.
Table of contents
Before Using the Product
Safety Precautions 8
Cleaning 8
Storage 8
Electricity and Safety 9
Installation 10
Operation 11
Preparations
Checking the Components 13
Components 13
Parts 14
Parts 14
Reverse Side 15
Remote Control 16
Before Installing the Product
(Installation Guide) 18
Tilting Angle and Rotation 18
Ventilation 18
Installing the Wall Mount 20
Installing the Wall Mount Kit 20
Wall Mount Kit Specifications 20
Remote Control (RS232C) 21
Cable Connection 21
Connection 24
Control Codes 25
2
Using MDC
MDC Programme Installation/Uninstallation 46
Installation 46
Uninstallation 46
Connecting to MDC 47
Using MDC via RS-232C
(serial data communications standards) 47
Using MDC via Ethernet 47
Player feature (except the
LH55OHFPSBC model)
Player 49
Viewing content 49
When content is running 50
Available menu 50
File Formats Compatible with Player 51
Schedule 56
Clone Product 57
ID Settings 58
Device ID 58
Device ID Auto Set 58
PC Connection Cable 58
Video Wall 59
Video Wall 59
Horizontal x Vertical 59
Screen Position 59
Format 60
Connecting and Using a Source Device
Before Connecting 33
Pre-connection Checkpoints 33
Before connecting cables 34
Connecting to a PC 35
Connection Using an HDMI-DVI Cable 35
Connection Using an HDMI Cable 35
Connecting to a Video Device 36
Using an HDMI cable or HDMI to DVI Cable
(up to 1080p) 36
Connection Using an HDMI-DVI Cable 36
Connection Using an HDMI Cable 36
Connecting the HDBase-T 37
Connecting to an Audio System 38
Connecting the LAN Cable 38
Changing the Input source
(except the LH55OHFPSBC model) 39
Source 39
Web Browser
(except the LH55OHFPSBC model) 40
Settings 40
Refresh Options 42
Changing the Input source (applies to the
LH55OHFPSBC model only) 43
Source 43
Web Browser 44
Table of contents
3
OnScreen Display (except the
LH55OHFPSBC model)
Display Orientation 80
Onscreen Menu Orientation 80
Source Content Orientation 80
Aspect Ratio 80
Screen Protection 81
Auto Protection Time 81
Screen Burn Protection 81
Message Display 84
Source Info 84
No Signal Message 84
MDC Message 84
Download Status Message 84
Language 85
Reset OnScreen Display 85
Dynamic Contrast 74
Black Tone 74
Flesh Tone 74
RGB Only Mode 74
Colour Space 74
HDMI UHD Color 75
Motion Lighting 75
Picture Options 76
Colour Tone 76
Digital Clean View 76
HDMI Black Level 77
Film Mode 77
Dynamic Backlight 77
Picture Size 78
Picture Size 78
Fit to Screen 78
Zoom/Position 78
Picture Off 79
Reset Picture 79
Network Status 61
Picture Mode 62
On/Off Timer 63
On Timer 63
Off Timer 64
Holiday Management 64
Ticker 65
URL Launcher 66
URL Launcher Settings 67
Approving a connected device from the server 68
Setting the current time 69
Screen Adjustment (except
the LH55OHFPSBC model)
Picture Mode 70
Backlight / Contrast / Brightness / Sharpness /
Colour / Tint (G/R) 71
Colour Temperature 72
White Balance 72
2 Point 72
10 Point 72
Gamma 73
Calibrated value 73
Advanced Settings 74
Table of contents
4
Input Device Manager 104
Keyboard Language 104
Keyboard type 104
Input Language Shortcut 104
Play via 104
Change PIN 105
Security 106
Safety Lock On 106
USB Auto Play Lock 106
Mobile Connection Lock 106
Remote Management 106
General 107
Smart Security 107
Anynet+ (HDMI-CEC) 108
HDMI Hot Plug 110
Custom Logo 110
Game Mode 111
Empty Storage 111
Reset System 111
Start Setup 96
Time 97
Clock Set 97
NTP Settings 97
DST 97
Sleep Timer 97
Power On Delay 97
Auto Source Switching 98
Auto Source Switching 98
Primary Source Recovery 98
Primary Source 98
Secondary Source 98
Power Control 99
Auto Power On 99
Max. Power Saving 99
Standby Control 99
Remote Configuration 100
Power Button 100
Eco Solution 101
Brightness Limit 101
Energy Saving Mode 101
Eco Sensor 101
Screen Lamp Schedule 102
No Signal Power Off 102
Auto Power Off 102
Fan and Temperature 103
Fan Control 103
Fan Speed Setting 103
Outdoor Mode 103
Temperature Control 103
Network (except the
LH55OHFPSBC model)
Network Status 86
Open Network Settings 86
Network type 86
Network Settings (Wired) 87
Network Setting (Wireless) 89
WPS(PBC) 91
Server Network Settings 92
Connect to server 92
MagicInfo Mode 92
Server Access 92
FTP Mode 92
Proxy server 92
Wi-Fi Direct 93
Mobile Device Manager 94
Access Notification 94
Mobile Device List 94
Device Name 94
System (except the
LH55OHFPSBC model)
Accessibility 95
Menu Transparency 95
High Contrast 95
Enlarge 95
Table of contents
5
Picture Options 132
Colour Tone 132
Digital Clean View 132
HDMI Black Level 132
Film Mode 132
Dynamic Backlight 132
Apply Picture Settings 133
Picture Size Settings 134
Picture Size 134
Fit to screen 134
Zoom and Position 134
Reset Picture 135
Network Status 123
On/Off Timer 124
On Timer 124
Off Timer 125
Holiday Management 125
Ticker 125
URL Launcher 126
URL Launcher Settings 126
Screen Adjustment (applies to
the LH55OHFPSBC model only)
Backlight / Brightness / Contrast / Sharpness 127
Colour Temperature 128
Advanced Settings 129
Picture Enhancer 129
HDR+ Mode 129
Colour 129
Tint (G/R) 129
White Balance 130
Gamma 130
Contrast Enhancer 130
Black Tone 130
Flesh Tone 131
RGB Only Mode 131
Colour Space Settings 131
Input Signal Plus 131
Motion Lighting 131
Support (except the
LH55OHFPSBC model)
Software Update 112
Update now 112
Auto update 112
Contact Samsung 112
Reset All 112
Player feature (applies to the
LH55OHFPSBC model only)
Player 113
Viewing content 113
When content is running 114
Available menu 114
File Formats Compatible with Player 115
Schedule 119
Clone Product 120
ID Settings 121
Device ID 121
Device ID Auto Set 121
PC Connection Cable 121
Video Wall 122
Video Wall 122
Horizontal x Vertical 122
Screen Position 123
Format 123
Table of contents
6
Remote Configuration 150
Power Button 150
Eco Solution 151
Brightness Limit 151
Energy Saving Mode 151
Eco Sensor 151
Screen Lamp Schedule 152
No Signal Power Off 152
Auto Power Off 152
Fan and Temperature 153
Fan Control 153
Fan Speed Setting 153
Outdoor Mode 153
Play via 154
Change PIN 154
Security 155
Safety Lock On 155
USB Auto Play Lock 156
Remote Management 156
Secured Protocol 156
Network Lock 156
USB Lock 156
General 157
Smart Security 157
Anynet+ (HDMI-CEC) 157
HDMI Hot Plug 159
Custom Logo 159
Game Mode 160
Empty Storage 160
Reset System 160
Connect to server 143
MagicInfo Mode 143
Server Access 143
FTP Mode 144
Proxy server 144
Device Name 144
System (applies to the
LH55OHFPSBC model only)
Accessibility 145
High Contrast 145
Enlarge 145
Start Setup 146
Time 147
Clock Set 147
NTP Settings 147
DST 147
Power On Delay 147
Auto Source Switching 148
Auto Source Switching 148
Primary Source Recovery 148
Primary Source 148
Secondary Source 148
Default Input 148
Power Control 149
Auto Power On 149
Max. Power Saving 149
Standby Control 149
OnScreen Display (applies to the
LH55OHFPSBC model only)
Display Orientation 136
Onscreen Menu Orientation 136
Source Content Orientation 136
Aspect Ratio 136
Screen Protection 137
Auto Protection Time 137
Screen Burn Protection 137
Message Display 138
Source Info 138
No Signal Message 138
MDC Message 138
Download Status Message 138
Language 139
Reset OnScreen Display 139
Network (applies to the
LH55OHFPSBC model only)
Network Status 140
Open Network Settings 140
Network Settings (Wired) 141
IPv6 143
IPv6 Status 143
Server Network Settings 143
Table of contents
7
Specifications
General 169
Preset Timing Modes 171
Appendix
Responsibility for the Pay Service (Cost to
Customers) 173
Not a product defect 173
A Product damage caused by customer's fault 173
Others 173
Optimum Picture Quality and Afterimage
Burn-in Prevention 174
Optimum Picture Quality 174
Prevention of Afterimage Burn-in 174
Licence 176
Terminology 177
Support (applies to the
LH55OHFPSBC model only)
Software Update 161
Update Now 161
Contact Samsung 161
Terms & Conditions 161
Reset All 161
Troubleshooting Guide
Requirements Before Contacting Samsung
Customer Service Centre 162
Testing the Product 162
Checking the Resolution and Frequency 162
Check the followings. 163
Q & A 167
8
Before Using the Product
Chapter 01
Safety Precautions
Warning A serious or fatal injury may result if instructions are not followed.
Caution Personal injury or damage to properties may result if instructions are
not followed.
Activities marked by this symbol are prohibited.
Instructions marked by this symbol must be followed.
Cleaning
Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
Take the following steps when cleaning.
1 Power off the product and computer.
2 Disconnect the power cord from the product.
Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric
shock may result.
3 Use water and a dry cloth to clean the protection glass.
Wipe with a clean wet cloth.
To remove tough stains, wipe using a cloth with a small amount of ethanol based cleaner.
Use a brush to remove any debris from the inlet and outlet opening.
To remove tough stains, wipe using a cloth with a small amount of ethanol based cleaner.
If washing with water, keep the pressure below 0.5 bar.
4 Connect the power cord to the product when cleaning is finished.
5 Power on the product and computer.
Storage
Due to the characteristics of high-glossy products, using a UV humidifier nearby may create white-
coloured stains on the product.
Contact Customer Service Centre if the inside of the product needs cleaning (service fee will be charged).
9
Electricity and Safety
Warning
Do not use a damaged power cord or plug, or a loose power socket.
An electric shock or fire may result.
Do not use multiple products with a single power socket.
Overheated power sockets may cause a fire.
Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
Insert the power plug all the way in so it is not loose.
An unsecure connection may cause a fire.
Connect the power plug to a grounded power socket (type 1 insulated devices only).
An electric shock or injury may result.
Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy
object.
Damage to the cord may result in a fire or electric shock.
Do not place the power cord or product near heat sources.
A fire or electric shock may result.
Clean any dust around the pins of the power plug or the power socket with a dry cloth.
A fire may result.
Caution
Do not disconnect the power cord while the product is being used.
The product may become damaged by an electric shock.
Only use the power cord provided with your product by Samsung. Do not use the power cord with other
products.
A fire or electric shock may result.
Keep the power socket where the power cord is connected unobstructed.
The power cord must be disconnected to cut off power to the product when an issue occurs.
Note that the product is not completely powered down by using only the power button on the
remote.
Hold the plug when disconnecting the power cord from the power socket.
An electric shock or fire may result.
10
Installation
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT
INSTALL THE PRODUCT NEAR HEAT SOURCES.
A fire may result.
Have a technician install the wall-mount hanger.
Installation by an unqualified person can result in an injury.
Only use approved cabinets.
Do not install the product in poorly ventilated spaces such as a bookcase or closet.
An increased internal temperature may cause a fire.
When installing the product, keep it at a distance from the wall so that it is well ventilated.
Refer to the Outdoor Installation Guide. (http://displaysolutions.samsung.com)
An increased internal temperature may cause a fire.
Keep the plastic packaging out of the reach of children.
Children may suffocate.
Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
The product may fall and become damaged and/or cause an injury.
Using the product in an area with excess vibration may damage the product or cause a fire.
Do not install the product within the reach of young children.
The product may fall and injure children.
As the front is heavy, install the product on a flat and stable surface.
Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen
or near a kitchen counter.
Precautions during installation and storage
After opening the cover, install the product within 1 hour under humidity of 60% or below. (P. 34)
Keep the predefined humidity while opening the cover or assembling the housing (e.g. connection of
external device, F/W update).
During operation and storage of the product, be sure to attach the cover.
Caution
Do not drop the product while moving.
Product failure or personal injury may result.
Do not set down the product on its front.
The screen may become damaged.
When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the
product is not protruding.
The product may fall and become damaged and/or cause an injury.
Install the product only on cabinets or shelves of the right size.
Set down the product gently.
Product failure or personal injury may result.
If the product is installed in an unusual location, the surrounding environment may cause a serious
quality problem. Therefore, be sure to contact Samsung Customer Service Center before installation.
Places where many fine dusts are generated, places where chemicals are used, places with too
high or low temperatures, places with a lot of moisture or water, transportation equipment such as
vehicles, airports and stations used continuously for a long time, and more.
11
Operation
Warning
There is a high voltage inside the product. Never disassemble, repair or modify the product yourself.
A fire or electric shock may result.
Contact Samsung Customer Service Centre for repairs.
If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord
immediately and contact Samsung Customer Service Centre.
An electric shock or fire may result.
Do not let children hang from the product or climb on top of it.
Children may become injured or seriously harmed.
Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a
serious injury.
Do not drop objects on the product or apply impact.
A fire or electric shock may result.
Do not move the product by pulling the power cord or any cable.
Product failure, an electric shock or fire may result from a damaged cable.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.
Sparks can cause an explosion or fire.
Do not lift or move the product by pulling the power cord or any cable.
Product failure, an electric shock or fire may result from a damaged cable.
Do not use or keep combustible spray or an inflammable substance near the product.
An explosion or fire may result.
Ensure the vents are not blocked by tablecloths or curtains.
An increased internal temperature may cause a fire.
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches,
etc) into the product (via the vent or input/output ports, etc).
Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Centre.
Product failure, an electric shock or fire may result.
Do not block the vent on the product. The product may not function properly due to potential
overheating.
Do not attempt to insert your fingers or objects into the vents.
Product failure or personal injury may result.
12
Caution
Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage
burn-in or defective pixels.
Activate power-saving mode or a moving-picture screen saver if you will not be using the product for
an extended period of time.
Disconnect the power cord from the power socket if you do not plan on using the product for an extended
period of time (vacation, etc).
Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
Use the product at the recommended resolution and frequency.
Your eyesight may deteriorate.
Do not hold the product upside-down or move it by holding the stand.
The product may fall and become damaged or cause an injury.
Looking at the screen too close for an extended period of time can deteriorate your eyesight.
Rest your eyes for more than 5 minutes for every 1 hour of product use.
Eye fatigue will be relieved.
Do not touch the screen when the product has been turned on for an extended period of time as it will
become hot.
Store small accessories out of the reach of children.
Exercise caution when adjusting the product angle or stand height.
Your hand or finger may get stuck and injured.
Tilting the product at an excessive angle may cause the product to fall and an injury may result.
Do not place heavy objects on the product.
Product failure or personal injury may result.
When using headphones or earphones, do not turn the volume too high.
Having the sound too loud may damage your hearing.
Be careful that children do not place the battery in their mouths when removed from the remote control.
Place the battery in a location that children or infants cannot reach.
If children have had the battery in their mouths, consult your doctor immediately.
When replacing the battery, insert it with the right polarity (+, -).
Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to
leakage of the internal liquid.
Use only the specified standardised batteries, and do not use a new battery and a used battery at the
same time.
Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage
of the internal liquid.
The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling
purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.
The customer can return used or rechargeable batteries to a nearby public recycling centre or to a
store selling the same type of the battery or rechargeable battery.
13
– Contact the vendor where you
purchased the product if any
components are missing.
– The pictures may look different from
the actual components.
– A stand is not provided with the
product. To install a stand, you can
purchase one separately.
Checking the Components
Components
QUICK SETUP GUIDE Warranty card
(Not available in some locations) Regulatory guide Power cord
+
+
-
-
Batteries (AAA x 2)
(Not available in some locations) Remote Control
Preparations
Chapter 02
14
Parts
Parts
The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
POWER
Power LED / Remote sensor
Parts Description
Remote sensor Press a button on the remote control pointing at the sensor on the front of the product to perform the corresponding function.
Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
Use the remote control within 7 m to 10 m from the sensor on the product at an angle of 30° from the left and right.
Store used batteries out of reach of children and recycle.
Do not use a new and used battery together. Replace both batteries at the same time.
Remove batteries when the remote control is not to be used for an extended period of time.
15
Reverse Side
The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
RS232C
IN
OUT
AUDIO
OUT USB
RJ45
(LAN OUT)
HDBT
(LAN IN) HDMI IN 1 HDMI IN 2
Port Description
RS232C IN Connects to MDC using an RS232C cable.
RS232C OUT
AUDIO OUT Outputs sound to an audio device via an audio cable.
USB Connect to a USB memory device.
RJ45 (LAN OUT) - Wired LAN connection port used to connect an external device such as a laptop to connect to the Internet.
- Connects to MDC and the Internet using a LAN cable. (10/100 Mbps)
HDBT (LAN IN) - Sends the HDMI signal to a connected LAN cable using an HDBaseT transmitter.
- Connects to MDC and the Internet using a LAN cable. (10/100 Mbps)
HDMI IN 1, HDMI IN 2 Connects to a source device using a HDMI cable or HDMI-DVI cable.
16
– Remote control button functions may
differ for different products.
– Remove batteries when the remote
control is not to be used for an
extended period of time.
Remote Control
Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
A button without a description in the image below is not supported on the product.
HOME
MENU
POWER
OFF
VOL
MagicInfo
Player I
.QZ
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
SYMBOL
0
PRS
7
TUV
8
WXY
9
MUTE
SOURCE
CH
DEL-/-- CH LIST
Power off the product.
Number buttons
Enter the password in the OSD menu, etc.
Mute the sound.
Unmuting the sound: Press MUTE again or press
the volume control (+ VOL -) button.
A shortcut button to Home screen (MagicInfo or
URL Launcher).
Power on the product.
Adjust the volume.
Change the input source.
Display or hide the onscreen display menu, or
return to the previous menu.
17
TOOLS INFO
SET
UNSET
LOCK
PC
A
DVI
B
HDMI
C
DP
D
EXITRETURN
IR control
Display information about the current input
source.
Move to the upper, lower, left or right menu, or
adjust an option's setting.
Confirm a menu selection.
Exit the current menu.
Manually select a connected input source from
HDMI 1 and HDMI 2.
It sets safe lock function.
Quickly select frequently used functions by
pressing it while a content is playing.
Return to the previous menu.
If multiple products are connected through the
Video Wall feature, press the SET button and
enter a Device ID using the numeric buttons.
Control the product using the remote control.
Cancel a value that has been set using the SET
button and control all connected products using
the remote control.
– Remote control button functions may
differ for different products.
To place batteries in the remote control (AAA x 2)
18
Before Installing the Product
(Installation Guide)
15 ˚
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
Ensure that an authorised installation company installs the wall mount.
Otherwise, it may fall and cause personal injury.
Make sure to install the specified wall mount.
Tilting Angle and Rotation
Contact Samsung Customer Service Centre for further details.
The product can be tilted at a maximum angle of 15° from a perpendicular wall surface.
To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
A
B
Air vent
Air intake
Figure 1.1 Side view
Ventilation
Installation on a Perpendicular Wall
A Minimum 50 mm
B Ambient temperature: Under 50°C
When installing the product on a perpendicular wall, allow at least 50 mm of space between the product and wall surface
for ventilation and ensure that the ambient temperature is kept below 50°C.
Do not block the vent on the product.
Refer to the Outdoor Installation Guide. (http://displaysolutions.samsung.com)
19
Installation on an Indented Wall
Contact Samsung Customer Service Centre for further details.
A Minimum 50 mm
B Minimum 50 mm
C Ambient temperature: Under 50°C
When installing the product on an indented wall, allow at least the space specified above between the product and wall for
ventilation and ensure that the ambient temperature is kept below 50°C.
Refer to the Outdoor Installation Guide. (http://displaysolutions.samsung.com)
A
B
B
C
Figure 1.2 Side view
20
Wall Mount Kit Specifications
Install your wall mount on a solid wall perpendicular to the floor. If you install the
product on a slanted wall, it may fall and result in severe personal injury.
Before attaching the wall mount to surfaces other than plaster board, please contact
your nearest service center for additional information.
Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications.
Screws that are too long may cause damage to the inside of the product.
For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ
depending on the wall mount specifications.
Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
Samsung is not liable for product damage or personal injury when wall mount is used or the consumer fails to follow the
product installation instructions.
Do not mount the product at more than a 15 degree tilt.
Always have two people mount the product on a wall.
Standard dimensions for wall mount kits are shown in the table below.
Unit: mm (inches)
Model name Screw hole specs (A * B) in
millimetres
Standard Screw Quantity
OH46F / OH55F 995 x 500 (39.2 x 19.7) M8 4
Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
Installing the Wall Mount
The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
Installing the Wall Mount Kit
The wall mount kit (sold separately) allows you to mount the product on the wall.
For detailed information on installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket.
Samsung is not responsible for any damage to the product or injury to yourself or others if you select to install the wall mount on your own.
21
Remote Control (RS232C)
Cable Connection
RS232C Cable
Interface RS232C (9 pins)
Pin TxD (No.2), RxD (No.3), GND (No.5)
Bit rate 9600 bps
Data bits 8 bit
Parity None
Stop bit 1 bit
Flow control None
Maximum length 15 m (only shielded type)
Pin assignment
1 2 3 4 5
6 7 8 9
5 4 3 2 1
9 8 7 6
<Male type> <Female type>
Pin Signal
1Detect data carrier
2Received data
3Transmitted data
4Prepare data terminal
5Signal ground
6Prepare data set
7Send request
8Clear to send
9Ring indicator
22
RS232C cable
Connector: 9-Pin D-Sub to Stereo Cable
5
16
9
-P2-
1
2
3
-P1-
-P1- -P1- -P2- -P2-
Male type Rx
Tx
Gnd
3
2
5
----------
----------
----------
2
1
3
Tx
Rx
Gnd
STEREO
PLUG
(3.5ø)
LAN Cable
Pin assignment
12345678
Pin No Standard Colour Signal
1 White and orange TX+
2 Orange TX-
3 White and green RX+
4 Blue NC
5 White and blue NC
6 Green RX-
7 White and brown NC
8 Brown NC
23
Connector : RJ45
Direct LAN cable (PC to HUB)
HDBT (LAN IN)
HUB
P1
P1P2
P2
Signal P1 P2 Signal
TX+ 1 <--------> 1 TX+
TX- 2 <--------> 2 TX-
RX+ 3 <--------> 3 RX+
RX- 6 <--------> 6 RX-
Cross LAN cable (PC to PC)
RJ45 P1 P2
HDBT (LAN IN)
Signal P1 P2 Signal
TX+ 1 <--------> 3 RX+
TX- 2 <--------> 6 RX-
RX+ 3 <--------> 1 TX+
RX- 6 <--------> 2 TX-
24
Connection
Ensure you connect each of the adapters to the correct RS232C IN or OUT port on the product.
Connection 1
RS232C
IN OUT
RS232C
IN OUT
RS232C
IN OUT
RS232C
IN OUT
Connection 2
HDBT (LAN IN) HDBT (LAN IN)
Connection 3
RS232C
OUT
HDBT (LAN IN) RS232C
IN OUT
RS232C
IN OUT
RS232C
IN OUT
25
Control Codes
Viewing control state (Get control command)
Header Command ID Data length Checksum
0xAA Command type 0
Controlling (Set control command)
Header Command ID Data length Data Checksum
0xAA Command type 1 Value
Command
No. Command type Command Value range
1Power control 0x11 0~1
2Volume control 0x12 0~100
3Input source control 0x14 -
4Screen mode control 0x18 -
5Screen size control 0x19 0~255
6Video wall mode control 0x5C 0~1
7Safety Lock 0x5D 0~1
8Video Wall On 0x84 0~1
9Video Wall User Control 0x89 -
All communications take place in hexadecimals. The checksum is calculated by adding up all values
except the header. If a checksum adds up to be more than 2 digits as shown below (11+FF+01+01=112),
the first digit is removed.
E.g. Power On & ID=0
Header Command ID Data length Data 1 Checksum
0xAA 0x11 1 "Power"
Header Command ID Data length Data 1 12
0xAA 0x11 1 1
To control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID
as "0xFE" and transmit commands. Commands will be executed by each device but ACK will not
respond.
26
Power control
Function
A product can be powered on and off using a PC.
Viewing power state (Get Power ON / OFF Status)
Header Command ID Data length Checksum
0xAA 0x11 0
Setting power ON/Off (Set Power ON / OFF)
Header Command ID Data length Data Checksum
0xAA 0x11 1 "Power"
"Power": Power code to be set on a product.
Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x11 "Power"
"Power": Power code to be set on a product.
Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x11 "ERR"
"ERR" : A code showing what error has occurred.
Volume control
Function
The volume of a product can be adjusted using a PC.
Viewing volume state (Get Volume Status)
Header Command ID Data length Checksum
0xAA 0x12 0
Setting the volume (Set Volume)
Header Command ID Data length Data Checksum
0xAA 0x12 1 "Volume"
"Volume": Volume value code to be set on a product. (0-100)
Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x12 "Volume"
"Volume": Volume value code to be set on a product. (0-100)
Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x12 "ERR"
"ERR" : A code showing what error has occurred.
27
Input source control
Function
The input source of a product can be changed using a PC.
Viewing input source state (Get Input Source Status)
Header Command ID Data length Checksum
0xAA 0x14 0
Setting the input source (Set Input Source)
Header Command ID Data length Data Checksum
0xAA 0x14 1 "Input Source"
"Input Source": An input source code to be set on a product.
0x0C Input source
0x20 MagicInfo
0x21 HDMI1
0x22 HDMI1_PC
0x23 HDMI2
0x24 HDMI2_PC
0x55 HDBT
HDMI1_PC and HDMI2_PC cannot be used with the Set command. They only respond to "Get" commands.
Available input sources may vary depending on the model.
MagicInfo is only available with models that contain the MagicInfo function.
Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x14 "Input
Source"
"Input Source": An input source code to be set on a product.
Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x14 "ERR"
"ERR" : A code showing what error has occurred.
28
Screen mode control
Function
The screen mode of a product can be changed using a PC.
Screen mode cannot be controlled when the Video Wall function is enabled.
Viewing screen status (Get Screen Mode Status)
Header Command ID Data length Checksum
0xAA 0x18 0
Setting the picture size (Set Picture Size)
Header Command ID Data length Data Checksum
0xAA 0x18 1 "Screen Mode"
"Screen Mode": A code that sets the product status
0x01 16 : 9
0x04 Zoom
0x31 Wide Zoom
0x0B 4 : 3
Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x18 "Screen
Mode"
"Screen Mode": A code that sets the product status
Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x18 "ERR"
"ERR": A code showing what error has occurred
Screen size control
Function
The screen size of a product can be changed using a PC.
Viewing the screen size (Get Screen Size Status)
Header Command ID Data length Checksum
0xAA 0x19 0
Ack
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x19 "Screen Size"
"Screen Size": product screen size (range: 0 – 255, unit: inch)
Nak
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x19 "ERR"
"ERR": A code showing what error has occurred
29
Video Wall Mode Control
Function
Video Wall mode can be activated on a product using a PC.
This control is only available on a product whose Video Wall is enabled.
Viewing video wall mode (Get Video Wall Mode)
Header Command ID Data length Checksum
0xAA 0x5C 0
Setting the video wall (Set Video Wall Mode)
Header Command ID Data length Data Checksum
0xAA 0x5C 1 "Video Wall Mode"
"Video Wall Mode": A code used to activate Video Wall mode on a product
Full
Natural
Ack
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x5C "Video Wall
Mode"
"Video Wall Mode": A code used to activate Video Wall mode on a product
Nak
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x5C "ERR"
"ERR": A code showing what error has occurred
Safety Lock On
Function
PC can be used to turn the Safety Lock On function on or off on a product.
This control is available regardless of whether or not the power is turned on.
Viewing the safety lock state (Get Safety Lock Status)
Header Command ID Data length Checksum
0xAA 0x5D 0
Enabling or disabling safety lock (Set Safety Lock Enable / Disable)
Header Command ID Data length Data Checksum
0xAA 0x5D 1 "Safety Lock"
"Safety Lock": Safety lock code to be set on a product
Ack
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x5D "Safety Lock"
"Safety Lock": Safety lock code to be set on a product
Nak
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x5D "ERR"
"ERR": A code showing what error has occurred
30
Video Wall On
Function
Turn Video Wall on or off on the product from your computer.
Get Video Wall On/Off Status
Header Command ID Data length Checksum
0xAA 0x84 0
Set Video Wall On/Off
Header Command ID Data length Data Checksum
0xAA 0x84 1 V.Wall_On
V.Wall_On: Video Wall code to be assigned to the product
Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x84 V.Wall_On
V.Wall_On : Same as above
Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x84 ERR
"ERR": A code showing what error has occurred
Video Wall User Control
Function
Turn the Video Wall function on or off on the product from your computer.
Get Video Wall Status
Header Command ID Data length Checksum
0xAA 0x89 0
Set Video Wall
Header Command ID Data length Val1 Val2 Checksum
0xAA 0x89 2 Wall_Div Wall_SNo
Wall_Div: Video Wall Divider code assigned to the product
31
10x10 Video Wall Model
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Off 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
10x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F
20x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F
30x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F
40x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F
50x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F
60x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F
70x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E N/A
80x81 0x82 0x83 0x84 0x85 0x86 0x87 0x88 0x89 0x8A 0x8B 0x8C N/A N/A N/A
90x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B N/A N/A N/A N/A
10 0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA N/A N/A N/A N/A N/A
11 0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 N/A N/A N/A N/A N/A N/A
12 0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 N/A N/A N/A N/A N/A N/A N/A
13 0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 N/A N/A N/A N/A N/A N/A N/A N/A
14 0xE1 0xE2 0xE3 0xE4 0xE5 0xE6 0xE7 N/A N/A N/A N/A N/A N/A N/A N/A
15 0xF1 0xF2 0xF3 0xF4 0xF5 0xF6 N/A N/A N/A N/A N/A N/A N/A N/A N/A
32
Wall_SNo: Product Number code assigned to the product
10x10 Video Wall Model : ( 1 ~ 100)
Set Number Data
1 0x01
2 0x02
... ...
99 0x63
100 0x64
Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Val2 Checksum
0xAA 0xFF 4 'A' 0x89 Wall_Div Wall_SNo
Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x89 ERR
"ERR": A code showing what error has occurred
33
Before Connecting
Pre-connection Checkpoints
Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
Check the types of ports at the back of the product you want to connect.
Connecting and Using a Source Device
Chapter 03
34
Before connecting cables
The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
Unfasten the screws, then remove the cover.
2
Silicone bar
Remove the appropriate silicone bar for the
thickness of the cable to connect.
Different hole sizes and corresponding cable
thickness for each:
* JACK
7 Ø hole x 2: Insert the 7 Ø cable
5.5 Ø hole x 6 : Insert the 5.5 Ø cable
3 Ø hole x 4 : Insert the 3 Ø cable
* POWER INLET
7 Ø hole x 1: Insert the 7 Ø cable
3Insert the appropriate cable into the hole from
which the silicone bar was removed.
4The cable should be connected as shown.
5Close the cover, then fasten the screws.
After all the cables are connected, make sure to
close the cover and fasten the screws to ensure it is
water tight.
Recommended torque : 10 - 12 kgf.cm
35
Connecting to a PC
Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
A PC can be connected to the product in a variety of ways.
Select a connection method suitable for your PC.
Connecting parts may differ in different products.
Connection Using an HDMI-DVI Cable
After connecting a computer to the product with an HDMI-DVI cable, make sure to configure the settings
as shown below to enable the video from the computer.
The appearance may differ depending on the product.
Connecting parts may differ in different products.
Audio is not available if the DVI port on the product is connected to the HDMI port on the PC using a DVI-HDMI
adapter.
Connection Using an HDMI Cable
The appearance may differ depending on the product.
Connecting parts may differ in different products.
HDMI IN 1, HDMI IN 2
36
Connecting to a Video Device
Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
You can connect a video device to the product using a cable.
Connecting parts may differ in different products.
Press the SOURCE button on the remote control to change the source.
Using an HDMI cable or HDMI to DVI Cable (up to 1080p)
For better picture and audio quality, connect to a digital device using an HDMI cable.
An HDMI cable supports digital video and audio signals, and does not require an audio cable.
The picture may not display normally (if at all) or the audio may not work if an external device that
uses an older version of HDMI mode is connected to the product. If such a problem occurs, ask the
manufacturer of the external device about the HDMI version and, if out of date, request an upgrade.
Be sure to use an HDMI cable with a thickness of 14 mm or less.
Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a connection
error may occur.
A basic high-speed HDMI cable or one with ethernet is recommended.
This product does not support the ethernet function via HDMI.
Connection Using an HDMI-DVI Cable
Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
The appearance may differ depending on the product.
Connecting parts may differ in different products.
Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable.
HDMI IN 1, HDMI IN 2
Connection Using an HDMI Cable
The appearance may differ depending on the product.
Connecting parts may differ in different products.
HDMI IN 1, HDMI IN 2
37
Connecting the HDBase-T
The appearance may differ depending on the product.
Connecting parts may differ in different products.
HDBT (LAN IN) transmits data from an external device to HDBase-T (Tx). Make sure to connect them directly using a LAN cable.
Data transmission is not available if HDBT (LAN IN) is connected to HDBase-T (Tx) through a hub.
HDBase-T works with unshielded twisted pair (UTP) or shielded twisted pair (STP) cables; but, to ensure CE compliance, STP cables and STP Connectors are required. STP cable and connectors are recommended to safeguard
against unpredictable environmental electrical noise which may impact performance. It is recommended to use an STP cable to maximize performance. Using a UTP cable or patch may decrease performance.
For a long distance (50 m) transmission using many LAN cables in a bundle, use FTP or STP type of cables. When using UTP cables adjacent to other cables, it may cause a trouble of signal transmission.
HDMI OUT
HDMI IN
HDBT (LAN IN) LAN
HDBase-T (Tx)
HDMI OUT
HDMI OUT
LAN Cable
38
Connecting to an Audio System
The appearance may differ depending on the product.
Connecting parts may differ in different products.
AUDIO OUT
Connecting the LAN Cable
The appearance may differ depending on the product.
Connecting parts may differ in different products.
HDBT (LAN IN)
Use Cat7(*STP Type) cable for the connection. (10/100 Mbps)
*Shielded Twist Pair
39
Changing the Input source (except the
LH55OHFPSBC model)
Source
SOURCESource
Source
Web Browser HDMI 1 HDMI 2
MagicInfo S
The displayed image may differ depending on the model.
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from source list
to display the screen of the selected source.
The input source can also be changed by using the SOURCE button on the remote control.
The screen may not display correctly if an incorrect source is selected for the source device you want to
convert to.
Edit
SOURCESourceuEditENTER E
Edit the name and device type of a connected external device.
The list can include the following source devices. Source devices on the list differ depending on the
selected source.
HDMI 1 / HDMI 2 / HDBT / Cable Box / Game Console / PC / Blu-ray player
You cannot edit the following sources.
MagicInfo S / URL Launcher / Web Browser
40
Web Browser (except the LH55OHFPSBC
model)
SOURCESourceWeb BrowserENTER E
Web Browser
The displayed image may differ depending on the model.
Connect a LAN cable to access Internet from the product, similar to accessing the Internet from a computer.
Settings
SOURCESourceWeb BrowseruSettingsENTER E
General
Hide Tabs and Toolbar automatically
If the browser tabs, menu or toolbar are not used for a while, they will automatically disappear. To make
them appear again, move the pointer or focus to the top of the screen.
Use / Do not use
Pop-up Blocker
Make your browsing experience more pleasant by blocking pop-up windows.
Use / Do not use
Reset Settings
All your customised web Browser settings will be reset to their default values. Your bookmarks and
history won't be affected.
Search Engine
If you enter a keyword in the URL/keyword input field, Web Browser will open the Search Results page.
Choose the search engine you want to use.
Google / Bing
41
Privacy & Security
Security Mode
Provides warnings about unsafe pages or blocks access to enhance Web Browser security.
This may slow the Web Browser down.
Use / Do not use
Private Browsing
When Private Browsing is active, your browsing history won't be recorded.
Use / Do not use
Do Not Track
Ask websites not to track you.
Use / Do not use
JavaScript
Allow all sites to run JavaScript for a better browsing experience.
Use / Do not use
Clear History
Clear your entire browsing history.
Clear History
Delete browsing data
Delete all browsing data such as cookies, cached images and data.
Your bookmarks and history won't be affected.
Delete browsing data
Blocked pages
Blocked pages
Blocks access to pages that you have listed in Blocked pages.
Use / Do not use
Blocked pages
Block or unblock specific pages.
Add
Approved pages
Approved pages
Enables web access only to pages that you have approved.
Use / Do not use
Password for Approved pages
Set a password for managing Approved pages.
Set Password
Approved Pages
Approve specific pages or remove them from Approved pages.
Add
42
Encoding
Choose an encoding method for web pages. The current setting is Auto.
Auto / Manual (Current : Unicode)
Refresh Options
SOURCESourceWeb BrowseruRefresh OptionsENTER E
Refresh Interval
Set the time for the web browser to wait before returning to the home page.
Off / 5 min / 10 min / 15 min / 30 min
Zoom1
Set the zoom scale to apply when the web browser is refreshed.
50% / 75% / 100% / 125% / 150%
Home Page
Set the website to display when the web browser is refreshed.
Samsung Display / Custom
Custom
Enter the URL to set as the home page.
Enter URL
Available only when Home Page is set to Custom.
43
Changing the Input source (applies to the
LH55OHFPSBC model only)
Source
SOURCE
Source
HDMI 1 HDMI 2 HDBTMagicInfo S Web Browser
The displayed image may differ depending on the model.
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from source list
to display the screen of the selected source.
The input source can also be changed by using the SOURCE button on the remote control.
The screen may not display correctly if an incorrect source is selected for the source device you want to
convert to.
Edit
SOURCEuEditENTER E
Edit the name and device type of a connected external device.
The list can include the following source devices. Source devices on the list differ depending on the
selected source.
HDMI 1 / HDMI 2 / HDBT / Cable Box / Game Console / PC / Blu-ray player
You cannot edit the following sources.
MagicInfo S / URL Launcher / Web Browser
44
Web Browser
SOURCE Web BrowserENTER E
Connect the network to access the Internet from the product like accessing the Internet from a computer.
Settings
SOURCE Web BrowseruSettingsENTER E
Refresh Interval
Set the time for the web browser to wait before returning to the home page.
Off / 5 min / 10 min / 15 min / 30 min
Zoom
Set the zoom scale to apply when the web browser is refreshed.
50% / 75% / 100% / 125% / 150% / 200% / 300%
Home Page
Set the website to display when the web browser is refreshed.
Samsung Display / Custom
Custom
Enter the URL to set as the home page.
Enter URL
Available only when Home Page is set to Custom.
Advanced Settings
General
Hide Tabs and Toolbar
automatically
If the browser tabs, menu or toolbar are not used for a while, they
will automatically disappear. To make them appear again, move the
pointer or focus to the top of the screen.
Use / Do not use
Hide Cursor in Touch Mode Hide the cursor to prevent interference with touch operation.
Use / Do not use
Pop-up Blocker Make your browsing experience more pleasant by blocking pop-up
windows.
Use / Do not use
Proxy Server Configure a proxy server for the web browser.
Use / Do not use
Reset Settings All your customised Web Browser settings will be reset to their default
values. Your bookmarks and history won't be affected.
Search Engine
If you enter a keyword in the URL/keyword input field, Web Browser will open the Search Results page.
Choose the search engine you want to use.
Google / Bing
45
Privacy & Security
Do Not Track Ask websites not to track you.
Use / Do not use
Delete History Delete your entire browsing history.
JavaScript Allow all sites to run JavaScript for a better browsing experience.
Use / Do not use
Delete browsing data Delete all browsing data such as cookies, cached images and data.
Your bookmarks and history won't be affected.
Encoding
Encoding Choose an encoding method for web pages. The current setting is
Auto.
Auto / Manual (Current : Unicode)
About
Display the current version of Web Browser.
46
MDC Programme Installation/Uninstallation
Installation
MDC installation can be affected by the graphics card, mother board and network conditions.
1 Click the MDC Unified installation programme.
2 Select a language for installation. Next, click "OK".
3 When the "Welcome to the InstallShield Wizard for MDC_Unified" screen appears, click "Next".
4 In the "License Agreement" window displayed, select "I accept the terms in the license agreement"
and click "Next".
5 In the displayed "Customer Information" window, fill out all the information fields and click "Next".
6 In the displayed "Destination Folder" window, select the directory path you want to install the
programme in and click "Next".
If the directory path is not specified, the programme will be installed in the default directory path.
7 In the displayed "Ready to Install the Program" window, check the directory path to install the
programme in and click "Install".
8 Installation progress will be displayed.
9 Click "Finish" in the displayed "InstallShield Wizard Complete" window.
Select "Launch MDC Unified" and click "Finish" to run the MDC programme immediately.
10 The MDC Unified shortcut icon will be created on the desktop after installation.
The MDC execution icon may not be displayed depending on the PC system or product specifications.
Press F5 if the execution icon is not displayed.
Uninstallation
1 Select Settings > Control Panel on the Start menu and double-click Add/Delete Program.
2 Select MDC Unified from the list and click Change/Remove.
Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC.
- For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme is available on the website.
Using MDC
Chapter 04
47
Connecting to MDC
Using MDC via RS-232C (serial data communications
standards)
An RS-232C serial cable must be connected to the serial ports on the PC and monitor.
The appearance may differ depending on the product.
RS232C OUT
RS232C IN
RS232C IN
RS232C OUTRS232C IN
Monitor 1
Monitor 2
Computer
Using MDC via Ethernet
Enter the IP for the primary display device and connect the device to the PC. Display devices can be
connected to each other using a LAN cable.
Connection using a direct LAN cable
The appearance may differ depending on the product.
Multiple products can be connected using the HDBT (LAN IN) port on the product and the LAN ports on the
HUB.
HDBT (LAN IN)
HUB
HDBT (LAN IN)
HDBT (LAN IN)
Monitor 1
Monitor 2
Computer
48
Connection using a cross LAN cable
The appearance may differ depending on the product.
Multiple products can be connected using the RS232C IN / OUT port on the product.
Monitor 1
Monitor 2
Computer
RS232C OUT
RS232C OUT
RS232C IN
RS232C IN
RJ45 (LAN OUT)
49
Player
HOME PlayerENTER E
Play a range of content such as channels with schedules assigned, templates or files.
Used
199.33 MB
Available
4.26 GB(95%)
1
2
3
4
5 6
Player
Filter By: All Options
No channels
Network Channel
Network File
My Templates
Internal Memory
The displayed image may differ depending on the model.
To use the Player feature, set Play via to MagicInfo in System.
No. Description
1Select between internal or external memory.
2Play content, templates and schedules configured on the server.
You can view whether the server is connected (approval) in the Player screen.
To view whether the server is connected when a Network Channel is running,
press INFO on the remote.
1 Select Network Channel from the Player screen. The No channels message
appears if no channel has been registered in Network Channel.
2 Network Channel will run.
3Play content stored on the server.
4Play a template stored in the internal memory.
5Select a content type as criterion to search for a desired content list.
6Set different options for Player.
Viewing content
1 Select either internal or external memory. The files saved in the selected memory appear.
2 Select the desired file. The content appears on the screen. (For more information on compatible file
formats, see the “File formats compatible with Player” section.)
Player feature (except the LH55OHFPSBC model)
Accessible using the HOME button on the remote control.
Chapter 05
50
When content is running
Control buttons on the remote
You can use buttons on your remote control to play, pause, or skip between content on the playlist.
Button Function
TOOLS Brings up the menu bar.
INFO Displays the information of the content.
►Goes to next file or page.
◄Goes to previous file or page.
E / ∆ / ³Plays or pauses slide show or video content.
´Stops displaying content and goes to the Player screen.
πRewinds the video content.
µFast forwards the video content.
Available menu
Press the TOOLS button on the remote control during content playback to configure settings.
Menu Description
Playlist View a list of content items currently playing.
Picture Mode Customises the screen settings for the content currently playing.
Sound Mode Customises the audio settings for the content currently playing.
Repeat Set the repeat mode.
Background Music Set the background music to be played when content is running.
Reset Reset the background music.
Pause Pause the background music.
Prev Play the previous background music on the list.
Next Play the next background music on the list.
Reset, Pause, Prev, Next only appear when the background music is set.
51
File Formats Compatible with Player
Supported file systems include FAT32 and NTFS.
A file with a vertical and horizontal resolution larger than the maximum resolution cannot be played.
Check the vertical and horizontal resolution of the file.
Check the supported video and audio Codec types and Versions.
Check the supported file versions.
PowerPoint version up to 97 – 2007 is supported
Only the last USB device that was connected is recognised.
Network Schedule Multiframe
Playback restrictions
A maximum of two video files (Video) can be played simultaneously.
In portrait playback mode, only one video file can be played at a time.
For Office files (PPT and Word files) and PDF files, only one file type is supported at a time.
LFD(.lfd) files are not supported.
Sound output restrictions
More than one sound output cannot be used.
Playback priority: network BGM > local BGM > video file in the main frame selected by the user
Network BGM: Settings can be configured in step 1 when creating a server schedule.
Local BGM: BGM settings can be configured using the tools displayed after the TOOLS button is pressed
during Player playback.
User-selected main frame: Main frame settings can be configured in step 2 when creating a server
schedule.
Template files and LFD(.lfd) files
Restrictions
Ensure a distributed folder (content / schedules) exists in Internal / USB memory.
Playback restrictions
A maximum of two video (Video) files can be played.
For Office files (PPT and Word files) and PDF files, only one file type is supported at a time.
Multiple videos (Video) cannot be played on a single display of a video wall simultaneously.
Sound output restrictions
More than one sound output cannot be used.
Playback priority: network BGM > local BGM > video file in the main frame selected by the user
52
Contents
File Extension Container Video Codec Resolution Frame rate
(fps)
Bit rate
(Mbps)
Audio Codec
*.avi
*.mkv
*.asf
*.wmv
*.mp4
*.mov
*.3gp
*.vro
*.mpg
*.mpeg
*.ts
*.tp
*.trp
*.mov
*.flv
*.vob
*.svi
*.m2ts
*.mts
AVI
MKV
ASF
MP4
3GP
MOV
FLV
VRO
VOB
PS
TS
SVAF
H.264 BP/MP/HP 4096x2160
40 AC3
LPCM
ADPCM(IMA, MS)
AAC
HE-AAC
WMA
DD+
MPEG(MP3)
60 80
Motion JPEG 30 80
MVC 1920 x 1080 60 20
MPEG4 SP/ASP
Window Media Video v9 (VC1)
MPEG2
MPEG1
Microsoft MPEG-4 v1, v2, v3 30 20
Window Media Video v7(WMV1),v8(WMV2)
H 263 Sorenson
VP6
*.webm WebM VP8 1920x1080 90 20 Vorbis
VP9 4096x2160
20
*.rmvb RMVB RV8/9/10 (RV30/40) 1920x1080 60 20 RealAudio 6
53
Video Audio Image
3D video is not supported.
Content with a resolution larger than the resolution specified in
the table above is not supported.
Video content with a Bit rate or Frame rate larger than the rate
specified in the table above can cause choppy video during
playback.
Video content will not play, or not play correctly, if there is an
error in the content or the container.
Some USB/digital camera devices may not be compatible with
the player.
Supports up to H.264, Level 4.1
H.264 FMO / ASO / RS, VC1 SP / AP L4 and AVCHD are not
supported.
For all Video codecs except MVC, VP8, VP6:
Below 1280 x 720: 60 frame max
Above 1280 x 720: 30 frame max
GMC 2 or higher is not supported.
Supports only BD MVC Spec.
Only one video file can play at a time if video files on the monitor
use incompatible codecs or the resolution is 1080 x 1920.
When a single video file is playing, Seamless mode is not
supported under the following conditions:
Incompatible codec (MVC, VP3, MJPEG) ↔ Incompatible codec
Incompatible codec ↔ Compatible codec
The resolution is different from that of the monitor
The frequency is different from that of the monitor
Audio content with a Bit rate or Frame rate larger than the rate
specified in the table above can cause choppy audio during
playback.
Audio content will not play, or not play correctly, if there is an
error in the content or the container.
Some USB/digital camera devices may not be compatible with
the player.
Supports up to WMA 10 Pro 5.1 channel. WMA lossless audio is
not supported.
QCELP, AMR NB/WB are not supported.
Compatible image file format : JPEG, PNG, BMP
32-bit, 24-bit and 8-bit BMP files are supported.
Supported maximum resolution : 4096 x 4096
Supported maximum file size: 20MB
Supported image effects : 9 effects
(Fade1, Fade2, Blind, Spiral, Checker, Linear, Stairs, Wipe,
Random)
54
Power Point PDF WORD
Compatible document file formats
Extension : ppt, pptx
Version : Office 97 ~ Office 2007
Functions not supported
Animation effect
3D shapes (which will be displayed in 2D)
Header and footer (some subitems are not supported)
Word Art
Align
A group alignment error may occur
Office 2007
SmartArt is not fully supported. 97 out of 115 subitems are
supported.
Object insertion
Half-width characters
Letter spacing
Charts
Vertical text
Some subitems are not supported
Slide notes and handout
Compatible document file formats
Extension : pdf
Functions not supported
Content less than 1 pixel not supported because of
performance degradation issue.
Masked Image, Tiled Image content not supported.
Content with Rotated Text, not supported.
3D Shadow Effects not supported.
Some characters not supported
(Special characters may be corrupted)
Compatible document file formats
Extension : .doc, .docx
Version : Office 97 ~ Office 2007
Functions not supported
Page background effect
Some paragraph styles
Word Art
Align
A group alignment error may occur
3D shapes (which will be displayed in 2D)
Office 2007
SmartArt is not fully supported. 97 out of 115 subitems are
supported.
Charts
Half-width characters
Letter spacing
Vertical text
Some subitems are not supported
Slide notes and handout
55
Template files LFD
Creation/editing/playback are only available in Template. Supported in Network Channel
Compatible document file formats
Extension : .lfd
56
Schedule
HOME ScheduleENTER E
AM
PM
AM
Sun Mon Tue Wed Thu Fri Sat
1
2
3
Schedule
All day All day All day All day All day
Network
Information
Location:
Internal Memory
Date:
**-**-**** ~
**-**-****
Repeat:
Daily
Time:
All day
Connected
The displayed image may differ depending on the model.
You can check the content’s playback schedule on the server, imported from an external storage, or on a
mobile device.
No. Description
1Select between server and external memory.
2View weekly schedule of content playback.
Select to view detailed information of each event.
3View a thumbnail image and brief information of the content.
57
Clone Product
HOME Clone ProductENTER E
Clone Product
The displayed image may differ depending on the model.
Export settings on the product to an external storage device. You can also import settings from an
external storage device.
This option is useful when assigning the same settings to several products.
When a duplicate file is not found on the external storage device
1 Connect the external storage device, then run the Clone Product function.
2 The No cloning file found on the external storage device. Export this device's settings to the external
storage device? message appears.
3 Select Export to export the settings.
When a duplicate file is found on the external storage device
1 Connect the external storage device, then run the Clone Product function.
2 The Cloning file found. Please select an option. message appears.
Run the Import from External Storage or Export to External Storage function.
Import from External Storage: Copy settings saved on an external storage device to the product.
Export to External Storage: Copy settings on the product to an external storage device.
After configuration is complete, the product is rebooted automatically.
58
ID Settings
HOME ID SettingsENTER E
ID Settings
The displayed image may differ depending on the model.
Assign an ID to a set.
Device ID
Enter the ID number of the product connected to the input cable for input signal reception. (Range:
0~224)
Press u/d to select a number, and press E.
Enter the number you want using the number buttons on the remote control.
Device ID Auto Set
This feature automatically allots an ID number to a device connected via an RS232C cable.
When multiple devices are connected, enable the feature on either the first or last device.
This function is only available on the first device within an RS-232C daisy chain.
PC Connection Cable
Select a method to connect to MDC to receive the MDC signal.
RS232C cable
Communicate with MDC via the RS232C-stereo cable.
RJ-45 (LAN)/Wi-Fi Network
Communicate with MDC via the RJ45 cable or a Wi-Fi network.
For the models (LH55OHF2VBC, LH46OHF2VBC) that do not support wireless communication, only the RJ-
45(LAN) menu appears.
59
Video Wall
HOME Video WallENTER E
Video Wall
The displayed image may differ depending on the model.
Customise the layout of multiple displays that are connected to form a video wall.
In addition, display part of a whole picture or repeat the same picture on each of the connected multiple
displays.
To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support
the MagicInfo function.
Video Wall
You can activate or deactivate Video Wall.
To organise a video wall, select On.
Off / On
Horizontal x Vertical
This feature automatically splits a videowall display based on a videowall matrix configuration.
Enter the videowall matrix.
The videowall display is split based on the configured matrix. The number of vertical or horizontal display
devices can be set within the range 1 and 15.
A videowall display can be split into a maximum of 100 screens.
The Horizontal x Vertical option is only enabled when Video Wall is set to On.
Screen Position
To rearrange split screens, adjust the number for each product in the matrix using the Screen Position
feature.
Selecting Screen Position will display the videowall matrix with the numbers assigned to the products
that form the videowall.
To rearrange products, use the direction buttons on the remote control to move a product to another
desired number. Press the E button.
Screen Position allows you to split the screen into a maximum of 100 views (15x15).
The Screen Position option is only enabled when Video Wall is set to On.
To use the function, make sure Horizontal x Vertical is configured.
60
Format
Select how to display images on the videowall display.
Full: Display images in full screen with no margin.
Natural: Display images in the original aspect ratio without enlarging or reducing the size.
The Format option is only enabled when Video Wall is set to On.
61
Network Status
HOME Network StatusENTER E
Network Status
The displayed image may differ depending on the model.
Check the current network and Internet connection.
62
Picture Mode
HOME Picture ModeENTER E
Picture Mode
The displayed image may differ depending on the model.
Select a picture mode (Picture Mode) suitable for the environment where the product will be used.
Videos/Images mode improves the picture quality of the video device. Text mode improves the picture
quality of the computer.
Shops & Shopping Centres
Suitable for shopping malls.
Select either Videos/Images or Text depending on the picture mode.
Offices & Schools
Suitable for offices and schools.
Select either Videos/Images or Text depending on the picture mode.
Terminals & Stations
Suitable for bus terminals and train stations.
Select either Videos/Images or Text depending on the picture mode.
Video Wall
Suitable for environments where videowall display are used.
Select either Videos/Images or Text depending on the picture mode.
Calibration
In this mode, the brightness, colour, gamma and uniformity settings customised using the colour
calibration programme Color Expert are applied.
To apply the Calibration mode properly, make sure you configure the picture quality settings,
such as brightness, colour, gamma and uniformity, using the colour calibration programme Color
Expert.
To download the Color Expert programme, visit www.samsung.com/displaysolutions.
63
On/Off Timer
HOME On/Off TimerENTER E
On/Off Timer
The displayed image may differ depending on the model.
You must set Clock Set before you can use this feature.
On Timer
Set On Timer so that your product turns on automatically at a time and on a day of your choosing.
The power is turned on with the specified volume or input source.
On Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the
current time first.
(On Timer 1 ~ On Timer 7)
Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you
can choose the days you want On Timer to turn on your product.
The check mark indicates days you’ve selected.
Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter
numbers. Use the left and right arrow buttons to change entry fields.
Volume: Set the desired volume level. Use the up and down arrow buttons to change the volume
level.
Source: Select the input source of your choice.
Content (when the Source is set to Internal/USB): From the USB device or internal memory, select a
file (e.g. music, photo, or video) to play just after the product is turned on.
This function is available only when a USB device is connected.
If there is no music file on the USB device or you don’t select a folder containing a music file, the Timer
function does not operate correctly.
If there is only one photo file in the USB, the Slide Show will not play.
If a folder name is too long, the folder cannot be selected.
Each USB you use is assigned its own folder. When using more than one of the same type of USB, make sure
the folders assigned to each USB have different names.
We recommend that you use a USB memory stick and a multi card reader when using On Timer.
The On Timer function may not work with USB devices with a built-in battery, MP3 players, or PMPs made by
some manufacturers because the product can take too long to recognise these devices.
64
Off Timer
Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer 1 ~ Off Timer
7)
Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you
can choose the days you want Off Timer to turn off your product.
The check mark indicates days you’ve selected.
Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter
numbers. Use the left and right arrow buttons to change entry fields.
Holiday Management
Timer will be disabled during a period specified as a holiday.
Add Holiday: Specify the period you want to add as a holiday.
Select the start and end dates of the holiday you want to add using the u/d buttons, and click the
Done button.
The period will be added to the list of holidays.
Start: Set the start date of the holiday.
End: Set the end date of the holiday.
Delete: Delete selected items from the list of holidays.
Edit: Select a holiday item and then change the date.
Set Applied Timer: Set the On Timer and Off Timer to not activate on public holidays.
Press E to select the On Timer and Off Timer settings you do not want to activate.
The selected On Timer and Off Timer will not activate.
65
Ticker
HOME TickerENTER E
Ticker
The displayed image may differ depending on the model.
Input text while a video or image is displayed and display the text on the screen.
Off / On
Message: Enter a message to display on the screen.
Time: Set the Start Time and End Time to display a Message.
Font options: Specify the text font and colour for the message.
Position: Select an orientation to display a Message.
Scroll: Specify the scroll Direction and Speed for the message.
Preview: Preview configured caption settings.
66
URL Launcher
HOME URL LauncherENTER E
URL Launcher
The displayed image may differ depending on the model.
For details on how to use the URL Launcher feature, contact the dealer the product was purchased from.
To use the URL Launcher feature, set Play via to URL Launcher in System.
67
URL Launcher Settings
HOME URL Launcher SettingsENTER E
URL Launcher
Settings
The displayed image may differ depending on the model.
Install Web App: Enter URL to install the web application.
Install from USB Device: Install the web application from the USB storage device.
Uninstall: Remove the installed web application.
Timeout Setting: Set the timeout period for connecting to the URL.
Developer Mode: Enable developer mode.
68
Approving a connected device from the server
First configure the server Server Network Settings before device approval.
1 Access the server you have assigned to your device.
2 Enter your ID and password to log in.
3 Select Device from the top menu bar.
4 Select Unapproved from the sub-menus.
5 Select the device from the list and click the Approve button.
6 Enter the information required to approve the device.
Device Name: Enter the device name.
Device Group: Select to specify the group.
Location: Enter the current location of the device.
Expired: Set expiry date for the device's approval. If you do not want to set the expiry date, select Never
expired.
Pressing the INFO button on the remote when a network schedule is running will display the details of the
schedule. Check that the correct device has been selected by viewing the device ID in the details.
69
7 Select the All menu to check that the device has been registered.
8 When the device is approved by the server, the schedule registered in the selected group will be
downloaded to the device. The schedule will run after it is downloaded.
For further details on how to configure a schedule, refer to the <MagicInfo Lite Server user's manual>.
If a device is deleted from the list of devices approved by the server, the device will reboot to reset its
settings.
Setting the current time
A schedule may not run if the time set on the device is different from the server's current time.
1 Select Device from the side menu bar.
2 Select your device.
3 Select EditSetup.
4 Select Time Zone.
When connecting to the server for the first time, the time on the product is set using the GMT time of the
region where the server is installed.
The time on the product can be changed from the server as shown in step 3.
Turning the product off and then on again will restore the time setting on the product to the last time that
was set from the server.
For further details on how to manage the time (scheduling, holiday management, etc.), refer to the <MagicInfo
Lite Server user's manual>.
70
Picture Mode
MENU mPicturePicture ModeENTER E
·
·
·
Picture
Picture Mode
Backlight
Contrast
Brightness
Sharpness
Colour
Tint (G/R)
100
70
45
65
50
G50 R50
The displayed image may differ depending on the model.
Select a picture mode (Picture Mode) suitable for the environment where the product will be used.
Videos/Images mode improves the picture quality of the video device. Text mode improves the picture quality of the computer.
Shops & Shopping Centres
Suitable for shopping malls.
Select either Videos/Images or Text depending on the picture mode.
Offices & Schools
Suitable for offices and schools.
Select either Videos/Images or Text depending on the picture mode.
Terminals & Stations
Suitable for bus terminals and train stations.
Select either Videos/Images or Text depending on the picture mode.
Video Wall
Suitable for environments where videowall display are used.
Select either Videos/Images or Text depending on the picture mode.
Calibration
In this mode, the brightness, colour, gamma and uniformity settings customised using the colour calibration programme
Color Expert are applied.
To apply the Calibration mode properly, make sure you configure the picture quality settings, such as brightness, colour,
gamma and uniformity, using the colour calibration programme Color Expert.
To download the Color Expert programme, visit www.samsung.com/displaysolutions.
Configure the Picture settings (Backlight, Colour Tone, etc.).
The layout of the Picture menu options may vary depending on the product.
Screen Adjustment (except the LH55OHFPSBC model)
Chapter 06
Shops & Shopping Centres
71
Backlight / Contrast / Brightness /
Sharpness / Colour / Tint (G/R)
MENU mPictureENTER E
·
·
·
Picture
Picture Mode
Backlight
Contrast
Brightness
Sharpness
Colour
Tint (G/R)
100
70
45
65
50
G50 R50
The displayed image may differ depending on the model.
Your product has several options for adjusting picture quality.
When you make changes to Backlight, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted accordingly.
You can adjust and store settings for each external device you have connected to an input on the product.
Lowering picture brightness reduces power consumption.
Shops & Shopping Centres
72
Colour Temperature
MENU mPictureColour TemperatureENTER E
Picture
Colour Temperature 16000K
The displayed image may differ depending on the model.
It sets colour temperature. The value and temperature increase simultaneously, so the ratio of blue colour rises. (Range:
2800K–16000K)
Enabled when Colour Tone is set to Off.
Colour Temperature is disabled if Picture Mode is set to Calibration.
White Balance
MENU mPictureWhite BalanceENTER E
Picture
White Balance
The displayed image may differ depending on the model.
2 Point
Adjust the colour temperature for a more natural picture.
R-Offset / G-Offset / B-Offset: Adjust each colour’s (red, green, blue) darkness.
R-Gain / G-Gain / B-Gain: Adjust each colour’s (red, green, blue) brightness.
Reset: Suitable for environments where videowall display are used.
10 Point
Controls the white balance in 10 point interval by adjusting the red, green, and blue brightness.
Off / On
Interval: Select interval to adjust.
Red: Adjust the red level.
Green: Adjust the green level.
Blue: Adjust the blue level.
Reset: Suitable for environments where videowall display are used.
Some external devices may not support this function.
Enabled when Picture Mode is set to Offices & Schools (Videos/Images).
73
Gamma
MENU mPictureGammaENTER E
Picture
Gamma 0
The displayed image may differ depending on the model.
Adjust the primary colour intensity.
If Picture Mode is set to Calibration, Gamma is disabled.
Calibrated value
MENU mPictureCalibrated valueENTER E
Don't apply
Picture
Calibrated value
The displayed image may differ depending on the model.
Select whether to apply the brightness, colour, gamma and uniformity settings customised using the colour calibration
programme Color Expert to the Information and Advertisement modes.
Don't apply / Apply
To download the Color Expert programme, visit www.samsung.com/displaysolutions.
If Picture Mode is set to Calibration, Calibrated value is disabled.
74
Advanced Settings
MENU mPictureAdvanced SettingsENTER E
Advanced Settings
Dynamic Contrast
Black Tone
Flesh Tone
RGB Only Mode
Colour Space
HDMI UHD Color
Motion Lighting
High
Darkest
0
Off
Native
On
The displayed image may differ depending on the model.
If Picture Mode is set to Calibration, Advanced Settings is disabled.
Dynamic Contrast
Adjust the screen contrast.
Off / Low / Medium / High
Black Tone
Select the black level to adjust the screen depth.
Off / Dark / Darker / Darkest
Flesh Tone
Emphasise pink Flesh Tone.
RGB Only Mode
Displays the Red, Green and Blue colour for making fine adjustments to the hue and saturation.
Off / Red / Green / Blue
Colour Space
Adjusts the range and variety of colours (the colour space) available to create images.
Auto / Native / Custom
To adjust Colour, Red, Green, Blue and Reset, set Colour Space to Custom.
75
Advanced Settings
Dynamic Contrast
Black Tone
Flesh Tone
RGB Only Mode
Colour Space
HDMI UHD Color
Motion Lighting
High
Darkest
0
Off
Native
On
The displayed image may differ depending on the model.
HDMI UHD Color
Enable to optimise picture quality for HDMI UHD connection.
HDMI1 (Off / On)
HDMI2 (Off / On)
Motion Lighting
Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
Off / On
Enabled when Picture Mode is set to Shops & Shopping Centres (Text).
76
Picture Options
MENU mPicturePicture OptionsENTER E
Picture Options
Colour Tone
Digital Clean View
HDMI Black Level
Film Mode
Dynamic Backlight
Off
Auto
Auto
Off
Off
The displayed image may differ depending on the model.
Colour Tone
If Picture Mode is set to Text
Off / Cool / Standard / Warm
If Picture Mode is set to Videos/Images
Off / Cool / Standard / Warm1 / Warm2
If Picture Mode is set to Calibration, Colour Tone is disabled.
Settings can be adjusted and stored for each external device connected to an input on the product.
Digital Clean View
Reduce picture noise to avoid distractions such as flickering.
Off / Auto
77
Picture Options
Colour Tone
Digital Clean View
HDMI Black Level
Film Mode
Dynamic Backlight
Off
Auto
Auto
Off
Off
The displayed image may differ depending on the model.
HDMI Black Level
Selects the black level on the screen to adjust the screen depth.
Auto / Low / Normal
Available only in HDMI 1 and HDMI 2 mode (AV Timing : 480p, 576p, 720p, 1080i, 1080p).
Film Mode
Make frame transitions from older video sources smoother. This function is only available when the input signal is TV, AV,
Component (480i, 1080i), or HDMI (1080i).
Off / Auto1 / Auto2
Dynamic Backlight
Automatically adjust the backlight to provide the best possible screen contrast under the current conditions.
Off / On
78
Picture Size
MENU mPicturePicture SizeENTER E
·
·
Picture Size
Picture Size
Fit to Screen
Zoom/Position
The displayed image may differ depending on the model.
choose size and aspect ratio picture displayed on screen.
Picture Size
Different screen adjustment options are displayed depending on the current input source.
Available ports may differ depending on the model.
16:9 Standard: Sets the picture to 16:9 Standard wide mode.
Custom: Changes the resolution to suit the user's preferences.
4:3: Sets the picture to basic (4:3) mode.
Do not set your product to 4:3 format for a long time.
The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn) which is not
covered by the warranty.
Fit to Screen
Adjusts the picture position. When selected, the full programme image will be displayed. No part of the image will be cut off.
Off / On / Auto
Zoom/Position
Adjusts the picture zoom and position. This option is available when the input source is set to HDMI 1, HDMI 2 (1080i/1080p).
Picture Size must be set to Custom for the option to be available.
If you want to reset the picture to its original position, select Reset in the Zoom/Position screen. The picture will be set to its default
position.
79
Picture Off
MENU mPicturePicture OffENTER E
Picture
Picture Off
The displayed image may differ depending on the model.
Selecting Picture Off switches off the screen. The volume is not disabled.
To switch the screen on, press any button other than the volume button.
Reset Picture
MENU mPictureReset PictureENTER E
Picture
Reset Picture
The displayed image may differ depending on the model.
Resets your current picture mode to its default settings.
80
OnScreen Display (except the LH55OHFPSBC model)
Display Orientation
MENU mOnScreen DisplayDisplay OrientationENTER E
Display Orientation
Onscreen Menu Orientation
Source Content Orientation
Aspect Ratio
Landscape
Landscape
Full Screen
The displayed image may differ depending on the model.
Onscreen Menu Orientation
Configure the menu screen.
Landscape: Display the menu in landscape mode (default).
Portrait: Display the menu in portrait mode on the right side of the product screen.
Source Content Orientation
Rotate the product screen orientation.
Landscape: Display the screen in landscape mode (default).
Portrait: Display the screen in portrait mode.
Aspect Ratio
Set the rotated screen to be either full screen or original.
Full Screen: Display the rotated screen in full screen.
Original ratio: Display the rotated screen in the original aspect ratio.
Available only when Source Content Orientation is set to Portrait.
Chapter 07
81
Screen Protection
MENU mOnScreen DisplayScreen ProtectionENTER E
Screen Protection
Auto Protection Time
Screen Burn Protection
Off
The displayed image may differ depending on the model.
Auto Protection Time
If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the
formation of burnt in ghost images on the screen.
Off / 2 hours / 4 hours / 8 hours / 10 hours
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped with Screen Burn Protection screen burn prevention technology.
Screen Burn Protection moves the picture slightly on the screen.
The Screen Burn Protection Time setting allows you to programme the time between movements of the picture in minutes.
Pixel Shift
Minimize image retention by finely moving pixels horizontally or vertically.
Pixel Shift (Off / On)
Horizontal, Vertical and Time are enabled only when Pixel Shift is set to On.
Horizontal: Sets how many pixels the screen moves horizontally.
Vertical: Sets how many pixels the screen moves vertically.
Time: Set the time interval for performing the horizontal or vertical movement, respectively.
Available Pixel Shift Settings and Optimum Settings.
Available Settings Optimum Settings
Horizontal (pixels) 0 ~ 4 4
Vertical (pixels) 0 ~ 4 4
Time (minute) 1 min ~ 4 min 4 min
The Pixel Shift value may differ depending on the product size (inches) and mode.
Displaying a still image or a 4:3 output for an extended period of time may cause image retention. This is not a defect in the product.
82
Screen Burn Protection
Pixel Shift
Timer
Immediate display Off
The displayed image may differ depending on the model.
Timer
You can set the timer for Screen Burn Protection.
The Screen Burn Protection feature stops automatically after a specified period of time.
Timer
Off
Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
Interval: Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to End
Time).
Mode, Period, Time, Start Time and End Time are enabled only when Timer is set to Repeat or Interval.
Mode: Select a screen protective pattern to display.
Pixel: Pixels on the screen alternate black continuously.
Rolling bar: A vertical bar moves left to right.
Fading screen: The entire screen becomes brighter, then darker.
The Rolling bar and Fading screen patterns appear only once regardless of the specified repeat period or time.
Period: Specify the time interval to activate the Screen Burn Protection function.
The option is enabled when Repeat is selected for Timer.
Time: Specify the duration to keep the Screen Burn Protection function on.
Enabled when Timer is set to Repeat and Mode is set to Pixel.
Start Time: Set the start time to activate the screen protection function.
The option is enabled when Interval is selected for Timer.
End Time: Set the end time to deactivate the screen protection function.
The option is enabled when Interval is selected for Timer.
83
Screen Burn Protection
Pixel Shift
Timer
Immediate display Off
The displayed image may differ depending on the model.
Immediate display
Select the screen saver you want to display immediately.
Off / Pixel / Rolling bar / Fading screen
84
Message Display
MENU mOnScreen DisplayMessage DisplayENTER E
Message Display
Source Info
No Signal Message
MDC Message
Download Status Message
On
On
On
Off
The displayed image may differ depending on the model.
Source Info
Select whether to display the source OSD when the input source changes.
Off / On
No Signal Message
Select whether to display the no-signal OSD when no signal is detected.
Off / On
MDC Message
Select whether to display the MDC OSD when the product is controlled by the MDC.
Off / On
Download Status Message
Select to display the status when downloading content from a server or other device.
Off / On
85
Language
MENU mOnScreen DisplayLanguageENTER E
OnScreen Display
Language English
The displayed image may differ depending on the model.
Set the menu language.
A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your
PC.
Reset OnScreen Display
MENU mOnScreen DisplayReset OnScreen DisplayENTER E
OnScreen Display
Reset OnScreen Display
The displayed image may differ depending on the model.
This option returns the current settings under OnScreen Display to the default factory settings.
86
Network Status
MENU mNetworkNetwork StatusENTER E
You can check the current network and Internet status.
Open Network Settings
MENU mNetworkOpen Network SettingsENTER E
Configure network settings to use various smart hub features such as Internet search, content sharing
through a home network and feature updates.
Network type
Wireless / Wired
For the models (LH55OHF2VBC, LH46OHF2VBC) that do not support wireless communication, the Wired
Network Settings menu appears.
Network (except the LH55OHFPSBC model)
Chapter 08
87
Network Settings (Wired)
Connecting to a Wired Network
There are three ways to attach your product to your LAN using cable.
You can attach your product to your LAN by connecting the LAN port on the back of your product to
an external modem using a LAN cable.
See the diagram below.
The Modem Port on the Wall
Modem Cable LAN Cable
External Modem
(ADSL / VDSL)
LAN
HDBT
(LAN IN)
You can attach your product to your LAN by connecting the LAN port on the back of your product to
an IP Sharer which is connected to an external modem. Use LAN cable for the connection. See the
diagram below.
The Modem Port on the Wall
Modem Cable LAN Cable LAN Cable
External Modem
(ADSL / VDSL)
IP Sharer
(having DHCP server)
LAN
HDBT
(LAN IN)
Depending on how your network is configured, you may be able to attach your product to your LAN
by connecting the LAN port on the back of your product directly to a network wall outlet using a LAN
cable.
See the diagram below. Note that the wall outlet is attached to a modem or router elsewhere in your
house.
The LAN Port on the Wall
LAN Cable
LAN
HDBT
(LAN IN)
If you have a Dynamic Network, you should use an ADSL modem or router that supports the Dynamic
Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the
IP address, subnet mask, gateway, and DNS values your product needs to access the Internet so you do
not have to enter them manually. Most home networks are Dynamic Networks.
Some networks require a Static IP address. If your network requires a Static IP address, you must enter
the IP address, subnet mask, gateway, and DNS values manually on your product Cable Setup Screen
when you set up the network connection. To get the IP address, subnet mask, gateway, and DNS values,
contact your Internet Service Provider (ISP).
If you have a Windows computer, you can also get these values through your computer.
You can use ADSL modems that support DHCP if your network requires a Static IP address.
ADSL modems that support DHCP also let you use Static IP addresses.
88
Set the network connection to use Internet services such as perform software upgrades.
Automatic Open Network Settings (Wired)
Connect to the network using a LAN cable.
Make sure a LAN cable is connected first.
How to set up automatically
1 Set Network type to Wired from the Open Network Settings page.
2 Press the Connect button to start Open Network Settings.
The Connect button is only enabled when the LAN cable is properly connected.
3 The network test screen appears and verifies the network connection.
When the connection has been verified, the “Wired network and Internet connection completed.”
message appears.
If the connection process fails, check the LAN port connection.
If the automatic process cannot find the network connection values or if you want to set the connection
manually, go to the next section, network setup.
Manual Open Network Settings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server
address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
How to set up manually
1 Set Network type to Wired from the Open Network Settings page.
2 Press the Connect button to start Open Network Settings.
The Connect button is only enabled when the LAN cable is properly connected.
3 The network test screen appears and the verification process starts. Press Stop. The verification
process stops.
4 Select IP Settings on network connection screen. The IP Settings screen appears.
5 Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry
process for each field in the IP Address.
Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.
6 When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
7 When the connection has been verified, the “Wired network and Internet connection completed.”
message appears.
89
Network Setting (Wireless)
Models that do not support wireless communication: LH55OHF2VBC, LH46OHF2VBC
Connecting to a Wireless Network
The LAN Port on the Wall
LAN Cable
Wireless IP sharer
(router having DHCP server)
Samsung recommends using IEEE 802.11n. When you play video over a network connection, the video
may not play smoothly.
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless
IP sharer is currently being used by another device nearby, this will result in interference and communication
failure.
Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is set to WEP, TKIP
or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products will not support a connection in
compliance with new Wi-Fi certification specifications.
If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push
Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and
WPA key in either mode.
Connection Methods: You can setup the wireless network connection in three ways.
Auto Setup (Using the Auto Network Search function), Manual Setup, WPS(PBC)
Automatic Network Setup (Wireless)
Most wireless networks have an optional security system that requires devices that access the network
to transmit an encrypted security code called an Access or Security Key. The Security Key is based on
a Pass Phrase, typically a word or a series of letters and numbers of a specified length you were asked
to enter when you set up security for your wireless network. If you use this method of setting up the
network connection, and have a Security Key for your wireless network, you will have to enter the Pass
Phrase during the automatic or manual setup process.
How to set up automatically
1 Set Network type to Wireless from the Open Network Settings page.
2 The Network function searches for available wireless networks. When done, it displays a list of the
available networks.
3 In the list of networks, press the ▲ or ▼ button to select a network, and then press the E button
twice.
If the desired wireless router does not appear, select Refresh to search again.
If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
4 If the Enter password. screen appears, go to step 5. If you select a wireless router that does not have
security, go to step 7.
5 If the router has security, enter the Enter password. (Security key or PIN).
6 When done, use the right arrow button to move the cursor to Done, and then press E. The network
connection screen appears and the verification process starts.
A connection with the router is established, but the Internet cannot be accessed.
7 When the connection has been verified, the “Your wireless network and Internet connection are
setup and ready to use.” message appears.
90
Manual Network Setup (Wireless)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server
address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
How to set up manually
1 Set Network type to Wireless from the Open Network Settings page.
2 The Network function searches for available wireless networks. When done, it displays a list of the
available networks.
3 In the list of networks, press the u or d button to select a network, and then press the E button
twice.
If the desired wireless router does not appear, select Refresh to search again.
If the router cannot be found after retrying, select the Stop button.
4 If the Enter password. screen appears, go to step 5. If you select a wireless router that does not have
security, go to step 7.
5 If the router has security, enter the Enter password. (Security key or PIN).
6 When done, use the right arrow button to move the cursor to Done, and then press E. The network
connection screen appears and the verification process starts.
7 Select Stop while network connections are being attempted. This will stop the connection.
8 Select IP Settings on network connection screen. The IP Settings screen appears.
9 Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry
process for each field in the IP Address.
Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.
10 When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
11 When the connection has been verified, the “Your wireless network and Internet connection are
setup and ready to use.” message appears.
91
WPS(PBC)
How to set up using WPS(PBC)
If your router has a WPS(PBC) button, follow these steps.
1 Set Network type to Wireless from the Open Network Settings page.
2 Select WPS(PBC), press E, and then press E again.
3 Press the WPS(PBC) button on your router within 2 minutes. Your product automatically acquires all
the network setting values it needs and connects to your network.
4 The network connection screen appears, and network setup is done.
92
Server Network Settings
MENU mNetworkServer Network SettingsENTER E
Connect to server
To run Player connect to a network.
Server Address / SSL / Port
If the SSL option is enabled, the server is configured to use https and data transfer is encrypted.
Enter the server IP address and port number. Use 7001 as the port number. (If unable to connect to the server
using port number 7001, check with your server administrator to find the correct port number and then
change the port number.)
MagicInfo Mode
Select the appropriate MagicInfo Mode depending on the environment where you are using the product.
Lite / Premium
Server Access
Select a method to connect the server network.
Allow / Deny
FTP Mode
Specify the FTP operating mode.
Active / Passive
Proxy server
Set up your proxy server connection and related functions.
Address / Port / ID / Password
Address / Port / ID and Password are enabled only when Proxy server is set to On.
93
Wi-Fi Direct
MENU mNetworkWi-Fi DirectENTER E
Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router.
Models that do not support wireless communication: LH55OHF2VBC, LH46OHF2VBC
To connect your mobile device with your product using Wi-Fi Direct, follow these steps:
1 Go to Wi-Fi Direct screen. The product starts to search devices.
2 Turn on the Wi-Fi Direct function on your device. Select the desired Wi-Fi device.
PBC (Push Button Configuration): Press the WPS(PBC) button on your Wi-Fi device within 2 minutes. Your product automatically acquires all the network setting values
it needs and connects to your network.
PIN: Input the displayed PIN on your device.
If you want to disconnect the device, select the connected Wi-Fi device, and then select Disconnected.
To use this function, your mobile device
should be supported by the Wi-Fi Direct.
94
Mobile Device Manager
Allow other devices on your network, like smart phones and tablets, to share content with your product.
Models that do not support wireless communication: LH55OHF2VBC, LH46OHF2VBC
Access Notification
Display a notification when a device is connected for the first time.
Turn off Access Notification to connect devices automatically.
The Wi-Fi Direct feature is not supported currently.
Off / First Time Only / Always On
Mobile Device List
View and manage connected devices.
Device Name
MENU mNetworkDevice NameENTER E
Select or enter a device name.
This name can be shown on network remote controls over the network.
[Signage]Display 1 ~ 6 / User Input
95
Accessibility
MENU mSystemAccessibilityENTER E
System
Accessibility
Start Setup
Time
Auto Source Switching
Power Control
Eco Solution
Fan and Temperature
The displayed image may differ depending on the model.
Menu Transparency
Adjust transparency of menu box.
High / Low
High Contrast
Set the background and font to high-contrast colours in Menu. Menu transparencies become opaque when the option is
selected.
Off / On
Enlarge
Set whether to enlarge highlighted item in Menu.
Off / On
System (except the LH55OHFPSBC model)
Chapter 09
96
Start Setup
MENU mSystemStart SetupENTER E
System
Accessibility
Start Setup
Time
Auto Source Switching
Power Control
Eco Solution
Fan and Temperature
The displayed image may differ depending on the model.
Go through the initial setup steps like you did the first time you used this product.
Enter your 4 digit PIN number. The default PIN number is “0-0-0-0".
If you want to change the PIN number, use the Change PIN function.
97
Time
MENU mSystemTimeENTER E
Time
Clock Set
NTP Settings
DST
Sleep Timer
Power On Delay
On
Off
0
The displayed image may differ depending on the model.
You can configure Clock Set or Sleep Timer. Configure various time-related settings.
Press the INFO button if you want to view the current time.
Clock Set
Select Clock Set. Select Date or Time, and then press E.
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to
move from one entry field to the next. Press E when done.
You can set the Date and Time directly by pressing the number buttons on the remote control.
NTP Settings
Set up the server URL and time zone to use the network time.
DST
Switches the DST (Daylight Saving Time) function on or off.
Off / On
Start Date: Set the start date of Daylight Saving Time.
End Date: Set the end date of Daylight Saving Time.
Time Offset: Select the correct time offset your timezone.
Start Date, End Date and Time Offset are enabled only when DST is set to On.
Sleep Timer
Automatically shuts off the product after a preset period of time.
(Off / 30 min / 60 min / 90 min / 120 min / 150 min / 180 min)
Use the up and down arrows to select a period of time, and then press E. To cancel Sleep Timer, select Off.
Power On Delay
When connecting multiple products, adjust the power-on time for each product to prevent power overload (within the range
0–50 seconds).
98
Turning on the display with Auto Source Switching On, and the previous video source selection is not active, the display will
automatically search the different video input sources for active video.
Auto Source Switching
When the Auto Source Switching is On, the display video source will automatically be searched for active video.
The Primary Source selection will be activated, if the current video source is not recognised.
Secondary Source selection will become active, if no primary video source is available.
If both the primary and secondary input sources are not recognised, the display will perform two searches for an active source,
each search checking the primary and then secondary source. If both searches fail, the display will return to the first video
source and display a message indicating that there is no signal.
Primary Source Recovery
Select whether to restore the selected primary input source when a primary input source is connected.
The Primary Source Recovery function is disabled if Primary Source is set to All.
Primary Source
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
The Secondary Source function is disabled if Primary Source is set to All.
Auto Source Switching
MENU mSystemAuto Source SwitchingENTER E
Auto Source Switching
Auto Source Switching
Primary Source Recovery
Primary Source
Secondary Source
Off
Off
All
HDMI 1
The displayed image may differ depending on the model.
99
Power Control
MENU mSystemPower ControlENTER E
Power Control
Auto Power On
Max. Power Saving
Standby Control
Remote Configuration
Power Button
Off
On
On
Off
Power on only
The displayed image may differ depending on the model.
Auto Power On
This feature automatically turns on the product as soon as it is plugged in. Pressing the power button is not needed.
Off / On
Max. Power Saving
Conserve power by turning off PC monitor when PC is not used for certain time.
Off / On
Standby Control
You can set the screen standby mode to be applied when an input signal is received.
Auto
Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.
The message No Signal will appear if no source device is connected.
Off
The message No Signal will appear if no input signals are detected.
If No Signal is displayed although a source device is connected, check the cable connection.
If No Signal Message is set to Off, the No Signal message does not appear.
If this is the case, set No Signal Message to On.
On
Power-saving mode will activate if no input signals are detected.
100
Remote Configuration
This feature keeps the network power on when the product turns off.
Off / On
Power Button
The power button on the remote control can be set to turn on the power or turn on or off the power.
Power on only: Set the power button on the remote control only to turn on the power.
Power on and off: Set the power button on the remote control to turn on or off the power.
Power Control
Auto Power On
Max. Power Saving
Standby Control
Remote Configuration
Power Button
Off
On
On
Off
Power on only
The displayed image may differ depending on the model.
101
Eco Solution
MENU mSystemEco SolutionENTER E
Eco Solution
Brightness Limit
Energy Saving Mode
Eco Sensor
Screen Lamp Schedule
No Signal Power Off
Auto Power Off
Off
Off
Off
Off
Off
Off
The displayed image may differ depending on the model.
Brightness Limit
Limit the screen's maximum backlight level.
Off: Off allows you to use the maximum brightness available.
On: On prevents the use of maximum brightness and saves energy.
Energy Saving Mode
Reduce the power consumption by adjusting the screen brightness.
Off / Low / Medium / High
Eco Sensor
To enhance your power savings, the picture settings will automatically adapt to the light in the room.
Off / On
Adjusting the Backlight setting under Picture while Eco Sensor is on will disable the Off.
If the screen contrast is not sufficient, set the Eco Sensor to Off. If the Eco Sensor is Off, it may not comply with energy standards.
Min. Backlight
When Eco Sensor is On, you can manually adjust the minimum screen brightness. Min. Backlight is the darkest backlight mode.
Make sure the Min. Backlight setting is lower than the Backlight setting.
If Eco Sensor is On, the display brightness may change (become slightly darker or brighter) depending on the surrounding light
intensity.
102
Screen Lamp Schedule
Screen Lamp Schedule
Enable or disable the lamp schedule.
Off / On
Schedule 1, Schedule 2
Time
The panel brightness will change to the brightness set in Lamp at a specified time.
Lamp
Adjust the panel brightness. A value closer to 100 makes the panel brighter.
0 ~ 100
No Signal Power Off
Save power by turning the device off when no signal is received from any source.
Off / 10 min / 15 min / 30 min / 60 min
Disabled when an attached PC is in power saving mode.
The product will automatically power off at a specified time. The time can be changed as required.
Auto Power Off
The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel within
select hours to prevent overheating.
Off / 4 hours / 6 hours / 8 hours
Eco Solution
Brightness Limit
Energy Saving Mode
Eco Sensor
Screen Lamp Schedule
No Signal Power Off
Auto Power Off
Off
Off
Off
Off
Off
Off
The displayed image may differ depending on the model.
103
Fan and Temperature
MENU mSystemFan and TemperatureENTER E
System
Fan and Temperature
The displayed image may differ depending on the model.
Protects the product by detecting the fan speed and internal temperature.
Fan Control
Selects auto or manual for the fan speed settings.
Auto / Manual
Fan Speed Setting
Sets the fan speed within a range of 0 and 100.
Enabled when Fan Control is set to Manual.
Outdoor Mode
Outdoor Mode to "On."
This feature keeps the internal temperature of the product steady so that the product can start properly when it is powered on.
Off / On
Do not disconnect the power cable when this feature is set to "On."
The product consumes more power when it is turned off if this feature is set to "On" rather than to "Off."
Temperature Control
This function detects the internal temperature of the product. You can specify the temperature range that is acceptable.
The default temperature is set to 90 C.
The recommended operating temperature for this product is 75 to 90 C (based on an ambient temperature of 50 C).
The screen will become darker if the current temperature exceeds the specified temperature limit. If the temperature continues to
rise, the product will power off to prevent overheating.
104
Configure options for external input devices connected to the product.
Keyboard Language
Configure the key combination used to change the input language.
Keyboard type
Specify the keyboard type.
Input Language Shortcut
Select shortcut keys for switching between input languages.
Input Device Manager
MENU mSystemInput Device ManagerENTER E
Input Device Manager
Keyboard Language
Keyboard type
Input Language Shortcut
The displayed image may differ depending on the model.
Select the appropriate Play via mode depending on the environment where you are using the product.
The home screen may be different depending on the setting.
MagicInfo / URL Launcher
Play via
MENU mSystemPlay viaENTER E
System
Play via MagicInfo
The displayed image may differ depending on the model.
105
The Change PIN screen will appear.
Choose any 4 digits for your PIN and enter it in Enter New PIN. Reenter the same 4 digits in Confirm New PIN.
The product has memorised your new PIN.
Default password: 0 - 0 - 0 - 0
Change PIN
MENU mSystemChange PINENTER E
System
Change PIN
The displayed image may differ depending on the model.
106
Security
MENU mSystemSecurityENTER E
Security
Safety Lock On
USB Auto Play Lock
Mobile Connection Lock
Remote Management
Power On Button On
On
Off
The displayed image may differ depending on the model.
Safety Lock On
Enter your 4 digit PIN number. The default PIN number is “0-0-0-0".
If you want to change the PIN number, use the Change PIN function.
All the menus and buttons of the product and remote control, except for the LOCK button on the remote control, will be locked
by the Safety Lock On function.
To unlock the menus and buttons, press the LOCK button and then enter the password (default password: 0-0-0-0).
Power On Button
Turn on this feature to enable the remote control's Power button to turn on the device while Safety Lock On is enabled.
Off / On
USB Auto Play Lock
Select whether to automatically play MagicInfo content saved on a connected USB device.
Off
Play MagicInfo content saved on the USB device automatically.
On
Do not play MagicInfo content saved on the USB device automatically.
Connecting a USB device containing MagicInfo content displays "USB Auto Play Lock : On" for five seconds.
Mobile Connection Lock
Restrict other devices on your network, such as smart phones and tablets, to share content with your signage.
Off / On
Remote Management
You can Allow or Deny external commands to access your device via a network.
The changed setting remains even after the product is turned off and on using the Panel key.
107
General
MENU mSystemGeneralENTER E
General
On
On
Off
Smart Security
Anynet+ (HDMI-CEC)
HDMI Hot Plug
Custom Logo
Game Mode
Empty Storage
The displayed image may differ depending on the model.
Smart Security
The security provided to protect your display device and connected storage devices against viruses includes.
Scan
Inspect your display device and connected storage devices to check for viruses.
Isolated List
This is the list of items that have been Isolated for containing viruses.
Real-Time Monitoring
Scans for viruses by monitoring the display device in real time.
Monitoring Results
Check the list of files, networks, and processes that have been blocked.
108
General
On
On
Off
Smart Security
Anynet+ (HDMI-CEC)
HDMI Hot Plug
Custom Logo
Game Mode
Empty Storage
The displayed image may differ depending on the model.
Anynet+ (HDMI-CEC)
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung
product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your
Samsung device has this feature, check if there is an Anynet+ logo on it.
Off / On
You can only control Anynet+ devices using the product remote control, not the buttons on the product.
The product remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
Anynet+ works when the AV device supporting Anynet+ is in the standby or on status.
Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
109
Troubleshooting for Anynet+
Problem Possible Solution
Anynet+ does not work. Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
Check if the Anynet+ device power cord is properly connected.
Check the Anynet+ device’s Video/Audio/HDMI cable connections.
Check whether Anynet+ (HDMI-CEC) is set to On in the System menu.
Check whether the remote control is Anynet+ compatible.
Anynet+ doesn’t work in certain situations. (initial setup)
If you have removed and then reconnected the HDMI cable, please make sure to search devices again or turn your product off
and on again.
Check if the Anynet+ function of the Anynet device is set on.
I want to start Anynet+. Check if the Anynet+ device is properly connected to the product and check if the Anynet+ (HDMI-CEC) is set to On in the
System menu.
I want to exit Anynet+. Press the SOURCE button on the product remote control and select a non- Anynet+ device.
The message “Disconnecting
Anynet+ device ...” appears on
the screen.
You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
Use the remote control after the product has completed Anynet+ configuration or has finished switching to Anynet+.
The Anynet+ device does not
play.
You cannot use the play function when initial setup is in progress.
The connected device is not
displayed.
Check whether or not the device supports Anynet+ functions.
Check whether or not the HDMI cable is properly connected.
Check whether Anynet+ (HDMI-CEC) is set to On in the System menu.
Search Anynet+ devices again.
Anynet+ requires an HDMI connection. Make sure the device is connected to your product with an HDMI cable.
Some HDMI cables may not support Anynet+ functions.
If the connection is terminated because there has been a power failure or the HDMI cable has been disconnected, please repeat
the device scan.
110
HDMI Hot Plug
This feature is used to activate the time delay to turn on a DVI/HDMI source device.
Off / On
Custom Logo
You can download, select, and set the display time of a custom logo that appears when the product turns on.
Custom Logo
You can select a custom logo (image/video) or turn off the custom logo display.
You must download the custom logo from an external USB device to set the custom logo.
Logo Display Time
If the type of custom logo is Image, you can set the Logo Display Time.
Download Logo File
You can download a custom logo into the product from an external USB device.
The file name of the custom logo you want to download must be saved as “samsung” in all small letters.
When there are multiple numbers of external USB connections, the product will attempt to download the custom logo from the
last device that has been connected to the product.
Custom logo file restrictions
For image type custom logo, only bitmap files (aRGB 32bpp format) are supported.
The resolution of the image type custom logo must be between a minimum of 128x64 and the maximum screen
resolution. (Horizontal/Vertical values of the resolution must be multiples of 4.)
For video type custom logo, only TS Stream types are supported.
The maximum supported video file is 150 MB. The recommended length of a video file is 20 seconds or less.
General
Smart Security
Anynet+ (HDMI-CEC)
HDMI Hot Plug
Custom Logo
Game Mode
Empty Storage
On
On
Off
The displayed image may differ depending on the model.
111
Reset System
MENU mSystemReset SystemENTER E
System
Reset System
The displayed image may differ depending on the model.
This option returns the current settings under system to the default factory settings.
General
Smart Security
Anynet+ (HDMI-CEC)
HDMI Hot Plug
Custom Logo
Game Mode
Empty Storage
On
On
Off
The displayed image may differ depending on the model.
Game Mode
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by
selecting game mode.
Off / On
Precautions and limitations for Game Mode
To disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.
Empty Storage
Delete files to make space for new content. Recently played files will not be deleted.
112
Software Update
MENU mSupportSoftware UpdateENTER E
The Software Update menu lets you upgrade your product software to the latest version.
Be careful not to turn off the power until the upgrade is complete. The product will turn off and on
automatically after completing the software upgrade.
When you upgrade software, all video and audio settings you have made will return to their default settings.
We advise you to write down your settings so that you can easily reset them after the upgrade.
Update now
Update the software to the latest version.
Current version: This is the software version already installed in the product.
Auto update
This feature automatically updates the product when not in use.
Off / On
Contact Samsung
MENU mSupportContact SamsungENTER E
View this information when your product does not work properly or when you want to upgrade the
software.
You can find information regarding our call centres and how to download products and software.
Contact Samsung and find the product Model Code and Software Version.
Reset All
MENU mSupportReset AllENTER E
This option returns all the current settings for a display to the default factory settings.
Support (except the LH55OHFPSBC model)
Chapter 10
113
Player
HOME PlayerENTER E
Play a range of content such as channels with schedules assigned, templates or files.
Player
Filter By: All Options
No channels
Network Channel
Network File
My Templates
Internal Memory
The displayed image may differ depending on the model.
– To use the Player feature, set Play via to MagicInfo in System.
(MENU mSystemPlay viaMagicInfo)
– You must set Clock Set before you can use this feature.
No. Description
Select between internal or external memory.
Play content, templates and schedules configured on the server.
You can view whether the server is connected (approval) in the Player screen. To
view whether the server is connected when a Network Channel is running, press
INFO on the remote control.
1 Select Network Channel from the Player screen. The No channels message
appears if no channel has been registered in Network Channel.
2 Network Channel will run.
Play content stored on the server.
Play templates stored in My Templates folder in the Internal Memory.
Select a content type as criterion to search for a desired content list.
Set different options for Player.
Viewing content
1 Select either internal or external memory. The files saved in the selected memory appear.
2 Select the desired file. The content appears on the screen. (For more information on compatible file
formats, see the “File formats compatible with Player” section.)
Accessible using the HOME button on the remote control.
Player feature (applies to the LH55OHFPSBC model only)
Chapter 11
114
When content is running
Control buttons on the remote control
You can play, pause, or skip the content on the playlist by pressing buttons on the remote control.
Button Function
TOOLS Brings up the menu bar.
INFO Displays the general information of the content.
►Goes to next file or page.
◄Goes to previous file or page.
E / ∆ / ³Plays or pauses slide show or video content.
´Stops displaying content and goes to the Player screen.
πRewinds the video content.
µFast forwards the video content.
If there is only one image file in the Internal Memory or USB, the Slide Show will not play.
If the name of a folder is too long on the USB, you cannot select the folder.
Portrait option for Content Orientation is not available for contents with a resolution higher than 3840 x
2160.
Content Size for videos with a resolution higher than 3840 x 2160 supports Full Screen only.
Available menu
Press the TOOLS button on the remote control during content playback to configure settings.
Menu Description
Playlist View a list of content items currently playing.
Channel List Network Channel / Internal Channel / USB
Repeat All / Repeat One Set the repeat mode.
Background Music Set the background music to be played when content is running.
Reset Reset the background music.
Pause Pause the background music.
Prev Play the previous background music on the list.
Next Play the next background music on the list.
Reset, Pause, Prev, Next only appear when the background music is set.
115
File Formats Compatible with Player
Supported file systems include FAT32 and NTFS.
A file with a vertical and horizontal resolution larger than the maximum resolution cannot be played.
Check the vertical and horizontal resolution of the file.
Check the supported video and audio Codec types and Versions.
Check the supported file versions.
PowerPoint version up to 97 – 2013 is supported
For USB-Internal Memory file transfer, click OptionsSend.
Location of template files
– Internal MemoryMagicinfoSlide folder
– Internal Memory transfer: Internal MemoryMy Templates folder
Location of other files (non-template)
– Internal MemoryMagicinfoSlide folder
– Internal Memory transfer: Under the root folder
Network Schedule Multiframe
Playback restrictions
1 to 3 FHD video files can be played simultaneously or only one UHD video file and one FHD video file
at a time. In portrait playback mode, 3 FHD video files can be played simultaneously or only one UHD
video file at a time.
For Office files (PPT and Word files) and PDF files, only one file type is supported at a time.
LFD(*.LFD) files are not supported.
Contents with a resolution higher than 3840 x 2160 are not supported.
Sound output restrictions
More than one sound output cannot be used.
Network BGM: Settings can be configured when creating a server schedule.
Local BGM: BGM settings can be configured using the tools displayed after the TOOLS button is pressed
during Player playback.
User-selected main frame: Main frame settings can be configured when creating a server schedule.
Template files(*.LFD)
Restrictions
Check that you have Contents and Schedules folders published to the USB storage device.
A properly published content appears as Published Content in the USB device.
When copying a content you published to a USB device (Published Content ) to the Internal Memory,
the content appears in Internal Memory as Published Content only. Contents and Schedules folders
are not visible under Internal Memory.
Playback restrictions
A maximum of two video (Video) files can be played.
For Office files (PPT and Word files) and PDF files, only one file type is supported at a time.
When playing more than one video files simultaneously, make sure that the display areas are not
overlapping one another.
Sound output restrictions
More than one sound output cannot be used.
116
Video codecs
File Extension Container Video Codec Resolution Frame rate
(fps)
Bit rate
(Mbps)
Audio Codec
*.avi
*.mkv
*.asf
*.wmv
*.mp4
*.mov
*.3gp
*.vro
*.mpg
*.mpeg
*.ts
*.tp
*.trp
*.flv
*.vob
*.svi
*.m2ts
*.mts
AVI
MKV
ASF
MP4
3GP
MOV
FLV
VRO
VOB
PS
TS
SVAF
H.264 BP/MP/HP 4096 x 2160
60 Dolby Digital
AC3
LPCM
ADPCM(IMA, MS)
AAC
HE-AAC
WMA
DD+
MPEG(MP3)
AC-4
OPUS
HEVC (H.265 - Main, Main10) 60 80
Motion JPEG 3840 x 2160 30 80
MVC 1920 x 1080 60 20
MPEG4 SP/ASP
Window Media Video v9 (VC1)
MPEG2
MPEG1
Microsoft MPEG-4 v1, v2, v3 30
Window Media Video v7(WMV1), v8(WMV2)
H 263 Sorenson
VP6
*.webm WebM VP8 1920 x 1080 60 20 Vorbis
VP9 3840 x 2160 80
*.rmvb RMVB RV8/9/10 (RV30/40) 1920 x 1080 60 20 RealAudio 6
117
Other restrictions
Codecs may not function properly if there is a problem with the content.
Video content does not play or does not play correctly if there is an error in the content or container.
Sound or video may not work if they have standard bit rates/frame rates above the TV’s compatibility
ratings.
If the Index Table is has an error, the Seek (Jump) function will not work.
When playing video over a network connection, the video may not play smoothly because of data
transmission speeds.
Some USB/digital camera devices may not be compatible with the TV.
HEVC codec is only available in MKV / MP4 / TS containers.
The MVC codec is supported partly.
Video decoders
H.264 UHD is supported up to Level 5.1, and H.264 FHD is supported up to Level 4.1. (TV does not
support FMO / ASO / RS)
HEVC UHD is supported up to Level 5.1, and HEVC FHD is supported up to Level 4.1.
HEVC 8K is supported up to Level 6.1.
VC1 AP L4 is not supported.
GMC 2 or above is not supported.
When a single video file is playing, Seamless mode is not supported under the following conditions:
Incompatible codec (MVC, VP3, MJPEG) ↔ Incompatible codec
Incompatible codec ↔ Compatible codec
The resolution is different from that of the monitor
The frequency is different from that of the monitor
Audio decoders
WMA is supported up to 10 Pro 5.1 channels, M2 profile.
WMA1, WMA lossless / Voice are not supported.
QCELP and AMR NB/WB are not supported.
Vorbis is supported for up to 5.1 channels.
Dolby Digital Plus is supported for up to 5.1 channels.
The supported sample rates are 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, and 48 kHz, and differ with the
codec.
Image
Compatible image file format: JPEG, PNG, BMP
32-bit, 24-bit and 8-bit BMP files are supported.
Supported maximum resolution: 7680 x 4320 (JPEG), 4096 x 4096 (PNG, BMP)
When playing 10 files in one LFD file - 5120 x 5120
Supported maximum file size: 20MB
Supported Slideshow Effect: 9 effects
(Fade1, Fade2, Blind, Spiral, Checker, Linear, Stairs, Wipe, Random)
118
Power Point PDF WORD
Compatible document file formats
Extension : ppt, pptx
Version : Office 97 ~ Office 2013
Functions not supported
Animation effect
3D shapes (which will be displayed in 2D)
Header and footer (some subitems are not supported)
Word Art
Align
A group alignment error may occur
Office 2007
SmartArt is not fully supported. 97 out of 115 subitems are
supported.
Object insertion
Half-width characters
Letter spacing
Charts
Vertical text
Some subitems are not supported
Slide notes and handout
Compatible document file formats
Extension : pdf
Functions not supported
Content less than 1 pixel not supported because of performance
degradation issue.
Masked Image, Tiled Image content not supported.
Content with Rotated Text, not supported.
3D Shadow Effects not supported.
Some characters not supported
(Special characters may be corrupted)
Compatible document file formats
Extension : .doc, .docx
Version : Office 97 ~ Office 2013
Functions not supported
Page background effect
Some paragraph styles
Word Art
Align
A group alignment error may occur
3D shapes (which will be displayed in 2D)
Office 2007
SmartArt is not fully supported. 97 out of 115 subitems are
supported.
Charts
Half-width characters
Letter spacing
Vertical text
Some subitems are not supported
Slide notes and handout
119
Schedule
HOME ScheduleENTER E
Schedule
Internal Memory Send Delete
Schedule your content on a local channel.
Select to create a
new schedule on this
channel
CH 2
CH 3
The default content will be played when there is no programme scheduled. You can change the default content
from the Options menu.
Sunday, JanuaryAM
The displayed image may differ depending on the model.
You can check the schedule imported from a selected storage device.
No. Description
Select the saved location of the schedule.
Create/Edit/Delete/View schedule of content playback.
120
Clone Product
HOME Clone ProductENTER E
Clone Product
MENU
The displayed image may differ depending on the model.
Export settings on the product to an external storage device. You can also import settings from an
external storage device.
This option is useful when assigning the same settings to several products.
When a duplicate file is not found on the external storage device
1 Connect the external storage device, then run the Clone Product function.
2 The No cloning file found on the external storage device. Export this device's settings to the external
storage device? message appears.
3 Select Export to export the settings.
When a duplicate file is found on the external storage device
1 Connect the external storage device, then run the Clone Product function.
2 The Cloning file found. Please select an option. message appears.
Run the Import from External Storage or Export to External Storage function.
Import from External Storage: Copy settings saved on an external storage device to the product.
After configuration is complete, the product is rebooted automatically.
Export to External Storage: Copy settings on the product to an external storage device.
121
ID Settings
HOME ID SettingsENTER E
ID Settings
The displayed image may differ depending on the model.
Assign an ID to a set.
Device ID
Set a unique ID number for each product. (Range: 0~224)
Press u/d to select a number, and press E.
Enter the number you want using the number buttons on the remote control.
Device ID Auto Set
This feature automatically allots an ID number to a device connected via an RS232C cable.
This function is only available on the first device within an RS-232C daisy chain.
PC Connection Cable
Select which type of cable you are using to connect the display to the PC.
RS232C cable
Communicate with MDC via the RS232C cable.
RJ-45 (LAN) Cable
Communicate with MDC via the RJ45 cable.
122
Video Wall
HOME Video WallENTER E
Video Wall
The displayed image may differ depending on the model.
Customise the layout of multiple displays that are connected to form a video wall.
In addition, display part of a whole picture or repeat the same picture on each of the connected multiple
displays.
To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support
the MagicInfo function.
Video Wall
You can activate or deactivate Video Wall.
To organise a video wall, select On.
Off / On
Horizontal x Vertical
This feature automatically splits a videowall display based on a videowall matrix configuration.
Enter the videowall matrix.
The videowall display is split based on the configured matrix. The number of vertical or horizontal display
devices can be set within the range 1 and 15.
A videowall display can be split into a maximum of 225 screens.
The Horizontal x Vertical option is only enabled when Video Wall is set to On.
123
Screen Position
To rearrange split screens, adjust the number for each product in the matrix using the Screen Position
feature.
Selecting Screen Position will display the videowall matrix with the numbers assigned to the products
that form the videowall.
To rearrange products, use the direction buttons on the remote control to move a product to another
desired number. Press the E button.
Screen Position allows you to split the screen into a maximum of 225 views (15 x 15).
The Screen Position option is only enabled when Video Wall is set to On.
To use the function, make sure Horizontal x Vertical is configured.
Format
Select how to display images on the videowall display.
Full: Display images in full screen with no margin.
Natural: Display images in the original aspect ratio without enlarging or reducing the size.
The Format option is only enabled when Video Wall is set to On.
Network Status
HOME Network StatusENTER E
Network Status
The displayed image may differ depending on the model.
Check the current network and Internet connection.
124
On/Off Timer
HOME On/Off TimerENTER E
On/Off Timer
The displayed image may differ depending on the model.
You must set Clock Set before you can use this feature.
On Timer
Set On Timer so that your product turns on automatically at a time and on a day of your choice.
The power is turned on with the specified volume or input source.
On Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the
current time first.
(On Timer 1 ~ On Timer 7)
While the internal/USB memory option can be used with On Timer for MagicInfo mode, it is recommended to
use an internal memory.
Proper operation of On Timer feature cannot be guaranteed if used with a battery powered USB device, which
can take longer to be recognised.
Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you
can choose the days you want On Timer to turn on your product.
The check mark indicates days you’ve selected.
Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter
numbers. Use the left and right arrow buttons to change entry fields.
Volume (For models with built-in speakers): Set the desired volume level. Use the up and down arrow
buttons to change the volume level.
Source: Select the input source of your choice.
Content (when the Source is set to Internal/USB for MagicInfo mode): From the USB device or
internal memory, select a file (e.g. music, photo, or video) to play just after the product is turned on.
125
Off Timer
Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer 1 ~ Off Timer
7)
Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you
can choose the days you want Off Timer to turn off your product.
The check mark indicates days you’ve selected.
Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter
numbers. Use the left and right arrow buttons to change entry fields.
Holiday Management
Timer will be disabled during a period specified as a holiday.
Add Holiday: Specify the period you want to add as a holiday.
Select the start and end dates of the holiday you want to add using the u/d buttons, and click the
Done button.
The period will be added to the list of holidays.
Start Date: Set the start date of the holiday.
End Date: Set the end date of the holiday.
Delete: Delete selected items from the list of holidays.
Edit: Select a holiday item and then change the date.
Set Applied Timer: Set the On Timer and Off Timer to not activate on public holidays.
Press E to select the On Timer and Off Timer settings you do not want to activate.
The selected On Timer and Off Timer will not activate.
Ticker
HOME TickerENTER E
Ticker
The displayed image may differ depending on the model.
Input text while a video or image is displayed and display the text on the screen.
You must set Clock Set before you can use this feature.
Off / On: Set whether or not to use Ticker.
Message: Enter a message to display on the screen.
Time: Set the Start Time and End Time to display a Message.
Font options: Specify the text font and colour for the message.
Position: Select a position to display a Message.
Scroll: Turn scroll effects of Ticker on or not. Specify the scroll Direction and Speed for the message.
Preview: Preview your Ticker settings.
126
URL Launcher
HOME URL LauncherENTER E
URL Launcher
URL Launcher
The displayed image may differ depending on the model.
For details on how to use the URL Launcher feature, contact the dealer the product was purchased from.
To use the URL Launcher feature, set Play via to URL Launcher in System.
(MENU mSystemPlay viaURL Launcher)
URL Launcher Settings
HOME URL Launcher SettingsENTER E
URL Launcher Settings
The displayed image may differ depending on the model.
For details on how to use the URL Launcher feature, contact the dealer the product was purchased from.
Install Web App: Enter URL to install the web application.
Install from USB Device: Install the web application from the USB storage device.
Uninstall: Remove the installed web application.
Timeout Setting: Set the timeout period for connecting to the URL.
Developer Mode: Enable developer mode.
127
Backlight / Brightness / Contrast /
Sharpness
MENU mPictureENTER E
Picture
Backlight
Brightness
Contrast
Sharpness
Colour Temperature
Advanced Settings
Picture Options
100
45
70
50
10000 K
The displayed image may differ depending on the model.
Your product has several options for adjusting picture quality.
You can adjust and store settings for each external device you have connected to an input on the product.
Lowering picture brightness reduces power consumption.
Screen Adjustment (applies to the LH55OHFPSBC model only)
Configure the Picture settings (Backlight, Colour Tone, etc.).
The layout of the Picture menu options may vary depending on the product.
Chapter 12
128
Colour Temperature
MENU mPictureColour TemperatureENTER E
Picture
Colour Temperature 10000 K
The displayed image may differ depending on the model.
It sets colour temperature. The value and temperature increase simultaneously, so the ratio of blue colour rises. (Range:
2800K–16000K)
Enabled when Colour Tone is set to Off.
129
Advanced Settings
MENU mPictureAdvanced SettingsENTER E
Advanced Settings
Picture Enhancer
HDR+ Mode
Colour
Tint (G/R)
White Balance
Gamma
On
Off
50
0
BT.1886
0
BT.1886
The displayed image may differ depending on the model.
Configure advanced picture settings to create your preferred picture.
Picture Enhancer
Displays enhanced colour and sharpness.
Off / On
HDR+ Mode
Automatically provide an optimal HDR effect based on the video source.
Off / On
Colour
Adjust the colour saturation levels. Colour saturation intensifies as the value nears 100. (Range: 0~100)
Tint (G/R)
Adjust the ratio of green to red tint levels. Increasing values intensifies the saturation of red and green colours. (Range: 0~50)
130
White Balance
Adjust the colour temperature of the picture so that white objects appear brighter.
2 Point
Adjust red, green, and blue luminosity levels in two sections for precise white balance optimisation.
R-Offset / G-Offset / B-Offset: Adjust the proportion of each of red, green and blue colours in dark
areas.
R-Gain / G-Gain / B-Gain: Adjust the proportion of each of red, green and blue colours in bright
areas.
Reset: Restore the white balance settings to the default values.
20 Point Settings
Controls the white balance in 20 point interval by adjusting the red, green, and blue brightness.
20 Point
Adjust red, green, and blue luminosity levels in twenty sections for precise white balance optimisation.
Off ( ) / On ( )
Interval: Select interval to adjust.
Red: Adjust the red level.
Green: Adjust the green level.
Blue: Adjust the blue level.
Reset: Restore the current level's 20 point White Balance to the default values.
Some external devices may not support this function.
Gamma
Adjust the mid-range brightness of the picture.
HLG / ST.2084 / BT.1886 / S Curve
Gamma settings HLG, ST.2084, and BT.1886 may change depending on the input video settings. For models
with the HDR+ Mode support, the Gamma settings HLG, ST.2084, and BT.1886 may change depending on the
input video and HDR+ Mode settings. If HDR+ Mode is set to Off, HLG, ST.2084, and BT.1886 settings may be
available depending on the input video. To adjust S Curve, set HDR+ Mode to Off.
HLG / ST.2084 / BT.1886 / S Curve
Adjust the HLG, ST.2084, BT.1886, S Curve levels of the picture.
Contrast Enhancer
Automatically balance the contrast to prevent excessive differences between bright and dark areas.
Off / Low / Medium / High
Black Tone
Select the black level to adjust the screen depth.
Off / Dark / Darker / Darkest
131
Flesh Tone
Adjust the flesh tone colour by increasing or decreasing red levels.
RGB Only Mode
Fine-tune the saturation and tint of the red, green, and blue colour channels.
Off / Red / Green / Blue
Colour Space Settings
Configure colour space settings to refine the spectrum of colours on your screen.
Colour Space
Choose a colour space.
Auto / Native / Custom
To adjust Colour, Red, Green, Blue and Reset, set Colour Space to Custom.
Input Signal Plus
Expands the input signal range for HDMI connections.
HDMI1 (Off ( ) / On ( ))
HDMI2 (Off ( ) / On ( ))
When Input Signal Plus is set to On, up to the 4096 x 2160p @ 60 Hz resolution is supported.
When Input Signal Plus is set to Off, up to the 1920 x 1080 @ 60 Hz resolution is supported.
Supported Resolutions for UHD Input Signals
Check the supported resolution for UHD input signals.
Resolution: 3840 x 2160p, 4096 x 2160p
Even if the UHD signal is input, display outputs as a 1920 x 1080 @ 60 Hz resolution on the actual screen.
If Input Signal Plus is set to Off
Frame rate
(fps)
Colour Depth /
Chroma Sampling
RGB 4:4:4 YCbCr 4:4:4 YCbCr 4:2:2 YCbCr 4:2:0
50 / 60 8 bit - - - O
If Input Signal Plus is set to On
Frame rate
(fps)
Colour Depth /
Chroma Sampling
RGB 4:4:4 YCbCr 4:4:4 YCbCr 4:2:2 YCbCr 4:2:0
50 / 60 8 bit O O O O
10 bit - - O O
12 bit - - O O
Motion Lighting
Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
Off / On
132
Picture Options
MENU mPicturePicture OptionsENTER E
Picture Options
Colour Tone
Digital Clean View
HDMI Black Level
Film Mode
Dynamic Backlight
Off
Off
Auto
Off
On
The displayed image may differ depending on the model.
Colour Tone
Select the colour tone that best suits your viewing preferences.
Off / Cool / Standard / Warm1 / Warm2 / Natural
Settings can be adjusted and stored for each external device connected to an input on the product.
Digital Clean View
Reduce picture noise to avoid distractions such as flickering.
Auto / Off
HDMI Black Level
Adjust the black level to optimise the HDMI picture brightness and contrast.
Normal / Low / Auto
Film Mode
Make frame transitions from older video sources smoother. This function is only available when the input signal is TV, AV,
Component (480i, 1080i), or HDMI (1080i).
Off / Auto1 / Auto2
Dynamic Backlight
Automatically adjust the backlight to provide the best possible screen contrast under the current conditions.
Off / On
133
Apply Picture Settings
MENU mPictureApply Picture SettingsENTER E
Picture
Apply Picture Settings All Sources
The displayed image may differ depending on the model.
Apply the picture settings to all external devices connected to the device or to the current source only.
All Sources / Current Source
134
Picture Size Settings
MENU mPicturePicture Size SettingsENTER E
Picture Size Settings
Picture Size
Off
Fit to screen
Zoom and Position
The displayed image may differ depending on the model.
Choose size and aspect ratio picture displayed on screen.
Picture Size
Different screen adjustment options are displayed depending on the current input source.
16:9 Standard: Sets the picture to 16:9 Standard wide mode.
Custom: Changes the resolution to suit the user's preferences.
4:3: Sets the picture to basic (4:3) mode.
Do not set your product to 4:3 format for a long time.
The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn) which is not
covered by the warranty.
Fit to screen
Adjusts the picture position. When selected, the full programme image will be displayed. No part of the image will be cut off.
Off / On / Auto
Zoom and Position
Adjusts the picture zoom and position. This function is available only if Picture Size is set to Custom.
If you want to reset the picture to its original position, select Reset in the Zoom and Position screen. The picture will be set to its
default position.
135
Reset Picture
MENU mPictureReset PictureENTER E
Picture
Reset Picture
The displayed image may differ depending on the model.
Restore all picture settings to the factory default.
136
OnScreen Display (applies to the LH55OHFPSBC model only)
Display Orientation
MENU mOnScreen DisplayDisplay OrientationENTER E
Display Orientation
Onscreen Menu Orientation
Source Content Orientation
Aspect Ratio
Landscape
Landscape
Full Screen
The displayed image may differ depending on the model.
Onscreen Menu Orientation
Select whether the onscreen menu should be displayed in landscape or portrait orientation.
Landscape: Display the menu in landscape mode.
Portrait: Display the menu in portrait mode on the right side of the product screen.
Source Content Orientation
Rotate the product screen orientation.
This feature is not available for input source resolutions higher than 7680 x 4320.
Landscape: Display the screen in landscape mode.
Portrait: Display the screen in portrait mode.
Aspect Ratio
Set the rotated screen to be either full screen or original.
Full Screen: Display the rotated screen in full screen.
Original ratio: Display the rotated screen in the original aspect ratio.
Available only when Source Content Orientation is set to Portrait.
Chapter 13
137
Screen Protection
MENU mOnScreen DisplayScreen ProtectionENTER E
Auto Protection Time
If the screen displays a still image for a certain period of time you define, the product activates the
screen saver to prevent the formation of burnt in ghost images on the screen.
Off / 2 hours / 4 hours / 6 hours / 8 hours / 10 hours
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped with Screen Burn Protection (screen burn
prevention technology).
Screen Burn Protection moves the picture slightly on the screen.
Timer
You can set the timer for Screen Burn Protection.
The Screen Burn Protection feature stops automatically after a specified period of time.
Timer
Off
Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
Interval: Display the image retention-preventive pattern set in Mode for a specified period of time (from
Start Time to End Time).
Mode, Period, Time, Start Time and End Time are enabled only when Timer is set to Repeat or Interval.
Mode: Select a screen protective pattern to display.
Pixel: Pixels on the screen alternate black continuously.
Rolling bar: A vertical bar moves left to right.
Fading screen: The entire screen becomes brighter, then darker.
The Rolling bar and Fading screen patterns appear only once regardless of the specified repeat period or
time.
Period: Specify the time interval to activate the Screen Burn Protection function.
The option is enabled when Repeat is selected for Timer.
Time: Specify the duration to keep the Screen Burn Protection function on.
Enabled when Timer is set to Repeat and Mode is set to Pixel.
Start Time: Set the start time to activate the screen protection function.
The option is enabled when Interval is selected for Timer.
End Time: Set the end time to deactivate the screen protection function.
The option is enabled when Interval is selected for Timer.
Immediate display
Select the screen saver you want to display immediately.
Off / Pixel / Rolling bar / Fading screen
138
Message Display
MENU mOnScreen DisplayMessage DisplayENTER E
Message Display
Source Info
No Signal Message
MDC Message
Download Status Message
On
On
On
Off
The displayed image may differ depending on the model.
Source Info
Select whether to display the source OSD when the input source changes.
Off / On
No Signal Message
Select whether to display the no-signal OSD when no signal is detected.
The message No Cable Connected will appear if no source device is connected.
Off / On
MDC Message
Select whether to display the MDC OSD when the product is controlled by the MDC.
Off / On
Download Status Message
Select to display the status when downloading content from a server or other device.
Off / On
139
Language
MENU mOnScreen DisplayLanguageENTER E
OnScreen Display
Language English
The displayed image may differ depending on the model.
Set the menu language.
A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your
PC.
Reset OnScreen Display
MENU mOnScreen DisplayReset OnScreen DisplayENTER E
OnScreen Display
Reset OnScreen Display
The displayed image may differ depending on the model.
This option returns the current settings under OnScreen Display to the default factory settings.
140
Network (applies to the LH55OHFPSBC model only)
Network Status
MENU mNetworkNetwork StatusENTER E
You can check the current network and Internet status.
Open Network Settings
MENU mNetworkOpen Network SettingsENTER E
Configure network settings to connect to an available network.
Chapter 14
141
Network Settings (Wired)
Connecting to a Wired Network
There are three ways to attach your product to your LAN using cable.
You can attach your product to your LAN by connecting the LAN port on the back of your product to
an external modem using a LAN cable.
See the diagram below.
The Modem Port on the Wall
Modem Cable LAN Cable
External Modem
(ADSL / VDSL)
LAN
HDBT
(LAN IN)
You can attach your product to your LAN by connecting the LAN port on the back of your product to
an IP Sharer which is connected to an external modem. Use LAN cable for the connection. See the
diagram below.
The Modem Port on the Wall
Modem Cable LAN Cable LAN Cable
External Modem
(ADSL / VDSL)
IP Sharer
(having DHCP server)
LAN
HDBT
(LAN IN)
Depending on how your network is configured, you may be able to attach your product to your LAN
by connecting the LAN port on the back of your product directly to a network wall outlet using a LAN
cable.
See the diagram below. Note that the wall outlet is attached to a modem or router elsewhere in your
house.
The LAN Port on the Wall
LAN Cable
LAN
HDBT
(LAN IN)
If you have a Dynamic Network, you should use an ADSL modem or router that supports the Dynamic
Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the
IP Address, Subnet Mask, Gateway, and DNS values your product needs to access the Internet so you do
not have to enter them manually. Most home networks are Dynamic Networks.
Some networks require a Static IP address. If your network requires a Static IP address, you must enter
the IP Address, Subnet Mask, Gateway, and DNS values manually on your product IP Settings when you
set up the network connection. To get the IP Address, Subnet Mask, Gateway, and DNS values, contact
your Internet Service Provider (ISP).
If you have a Windows computer, you can also get these values through your computer.
You can use ADSL modems that support DHCP if your network requires a Static IP address.
ADSL modems that support DHCP also let you use Static IP addresses.
142
Set the network connection to use Internet services such as perform software upgrades.
Automatic Open Network Settings (Wired)
Connect to the network using a LAN cable.
Make sure a LAN cable is connected first.
How to set up automatically
1 Select Open Network Settings. The Open Network Settings session starts.
2 The network test screen appears and verifies the network connection.
When the connection has been verified, the “Success! Your device is connected to the Internet. If you
have any problems using online services, please contact your Internet service provider.” message
appears.
If the connection process fails, check the LAN port connection.
If the automatic process cannot find the network connection values or if you want to set the connection
manually, go to the next section(Manual Open Network Settings (Wired)).
Manual Open Network Settings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP Address, Subnet Mask, Gateway and DNS
server address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
The path to the settings depends on the installed OS.
How to set up manually
1 Select Open Network Settings. The Open Network Settings session starts.
2 The network test screen appears and the verification process starts. Press Cancel. The verification
process stops.
3 Select IP Settings on network connection screen. The IP Settings screen appears.
4 Select the field at the top, press E, and then set IP setting to Enter manually. Repeat the entry
process for each field in the IP Address.
Setting IP setting to Enter manually automatically changes DNS setting to Enter manually.
5 When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
6 When the connection has been verified, the “Success! Your device is connected to the Internet. If you
have any problems using online services, please contact your Internet service provider.” message
appears.
143
IPv6
MENU mNetworkIPv6ENTER E
Enable or disable IPv6.
Off ( ) / On ( )
IPv6 Status
MENU mNetworkIPv6 StatusENTER E
Check the status of your IPv6 Internet connection.
Server Network Settings
MENU mNetworkServer Network SettingsENTER E
Connect to server
Connect to MagicInfo server.
Server Address / TLS / Port
If you do use the TLS option, the server is configured to use https and data transfer is encrypted. (Port
number: 7002)
If you don't use the TLS option, enter the server IP address and port number. Use 7001 as the port number. (If
you are unable to connect to the server using port number 7001, check with your server administrator to find
the correct port number and then change the port number.)
Enter the server IP address and port number. Use 7001 as the port number. (If unable to connect to the server
using port number 7001, check with your server administrator to find the correct port number and then
change the port number.)
For the MagicInfo Server user guide, visit the following website: http://displaysolutions.samsung.com
SupportResourcesMagicInfo Web Manual.
MagicInfo Mode
Select the appropriate MagicInfo Mode depending on the environment where you are using the product.
Lite / Premium
Supported content types may be limited while MagicInfo Mode is set to Lite.
Server Access
Allow or deny access to MagicInfo server.
Allow / Deny
144
FTP Mode
Specify the FTP operating mode.
Active / Passive
Proxy server
Set up your proxy server connection and related functions.
Off / On
Address / Port / ID / Password
Address / Port / ID and Password are enabled only when Proxy server is set to On.
Device Name
MENU mNetworkDevice NameENTER E
Select or enter a device name.
This name can be shown on network device over the network.
[Signage] Display1 ~ 6 / User Input
145
System (applies to the LH55OHFPSBC model only)
Accessibility
MENU mSystemAccessibilityENTER E
System
Accessibility
Start Setup
Time
Auto Source Switching
Power Control
Eco Solution
Fan and Temperature
The displayed image may differ depending on the model.
Chapter 15
High Contrast
Set the background and font to high-contrast colours in Menu. Menu transparencies become opaque when the option is
selected.
Off ( ) / On ( )
Enlarge
Enlarge the size of the Menu area.
Off ( ) / On ( )
146
Go through the initial setup steps like you did the first time you used this product.
Enter your 4 digit PIN number. The default PIN number is "0-0-0-0".
If you want to change the PIN number, use the Change PIN function.
Change the PIN to keep your device secure.
Start Setup
MENU mSystemStart SetupENTER E
System
Start Setup
The displayed image may differ depending on the model.
147
Time
MENU mSystemTimeENTER E
Time
Clock Set
NTP Settings
DST
Power On Delay
Off
0
The displayed image may differ depending on the model.
You can configure Clock Set or DST. Configure various time-related settings.
Clock Set
Select Clock Set. Select Date or Time, and then press E.
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to
move from one entry field to the next. Press E when done.
You can set the Date and Time directly by pressing the number buttons on the remote control.
NTP Settings
Set up the server URL and time zone to use the network time.
DST
Switches the DST (Daylight Saving Time) function on or off.
Off / On
Start Date: Set the start date of Daylight Saving Time.
End Date: Set the end date of Daylight Saving Time.
Time Offset: Select the correct time offset for your timezone.
Start Date, End Date and Time Offset are enabled only when DST is set to On.
Power On Delay
When connecting multiple products, adjust the power-on time for each product to prevent power overload (within the range
0–50 seconds).
148
Auto Source Switching
MENU mSystemAuto Source SwitchingENTER E
Auto Source Switching
Auto Source Switching
Primary Source Recovery
Primary Source
Secondary Source
Default Input
Off
Off
All
HDMI1
Last Input
The displayed image may differ depending on the model.
Auto Source Switching
Switch to preset source or another source when the main source device gets disconnected.
Primary Source Recovery
Select whether to restore the selected primary input source when a primary input source is activated.
The Primary Source Recovery function is disabled if Primary Source is set to All.
Primary Source
Select a primary source to switch to when no signals are received from the current input.
Secondary Source
Select a secondary source to switch to when no signals are received from the current input.
The Secondary Source function is disabled if Primary Source is set to All.
Default Input
Select the default input to switch to when the new input is disconnected. The Last Input option only includes external inputs
connected via cables.
Auto Source Switching must be set to New Input to enable the Default Input option.
149
Power Control
MENU mSystemPower ControlENTER E
Power Control
Auto Power On
Max. Power Saving
Standby Control
Remote Configuration
Power Button
Off
On
On
Off
Power on only
The displayed image may differ depending on the model.
Auto Power On
This feature automatically turns on the product as soon as it is plugged in. Pressing the power button is not needed.
Off / On
Max. Power Saving
Conserve power by turning off PC monitor when PC is not used for certain time.
Off / On
Standby Control
When no signal is detected, it determines whether or not to enter sleep mode.
Auto
The display stays off to save energy until working signals are detected even if there is an external device connected.
The message No Cable Connected will appear if no source device is connected.
Off
The message No Signal will appear if no input signals are detected.
If the message, "No Signal" appears even though a source device is connected, check the cable connections and the settings of
your source device.
If No Signal Message is set to Off, the No Signal message does not appear.
In this case, set No Signal Message to On.
On
The display turns off to save energy if no input signals are detected.
150
Power Control
Auto Power On
Max. Power Saving
Standby Control
Remote Configuration
Power Button
Off
On
On
Off
Power on only
The displayed image may differ depending on the model.
Remote Configuration
This feature keeps the network power on when the product turns off.
Off / On
Power Button
The power button on the remote control can be set to turn on the power or turn on or off the power.
Power on only: Set the power button on the remote control only to turn on the power.
Power on and off: Set the power button on the remote control to turn on or off the power.
151
Brightness Limit
Turn the Brightness Limit on or off. If you select On, the display won't have the maximum brightness, but you will save energy.
Off / On
Energy Saving Mode
Reduce the power consumption by adjusting the screen brightness.
Off / Low / Medium / High
Eco Sensor
Automatically adjust the picture brightness based on the ambient light level.
Off / On
If the screen contrast is not sufficient, set the Eco Sensor to Off. If the Eco Sensor is Off, it may not comply with energy standards.
Minimum Backlight
Set the minimum brightness for the signage screen. This function only works if its value is lower than the value set in the
Picture menu's Backlight setting.
If Eco Sensor is On, the display brightness may change (become slightly darker or brighter) depending on the surrounding light
intensity.
Available only when Eco Sensor is set to On.
Eco Solution
MENU mSystemEco SolutionENTER E
Eco Solution
Brightness Limit
Energy Saving Mode
Eco Sensor
Screen Lamp Schedule
No Signal Power Off
Auto Power Off
Minimum Backlight
On
Off
Off
Off
15 minutes
Off (Recommended)
0
The displayed image may differ depending on the model.
152
Screen Lamp Schedule
Screen Lamp Schedule
Enable or disable the lamp schedule.
Off / On
Schedule 1, Schedule 2
Time
The panel brightness will change to the brightness set in Lamp at a specified time.
Lamp
Adjust the panel brightness. A value closer to 100 makes the panel brighter.
0 ~ 100
No Signal Power Off
Save power by turning the product off when no signal is received from any source.
This function does not operate if the display is in the standby mode.
The product will automatically power off at a specified time. The time can be changed as required.
Auto Power Off
Choose how long the display will wait before turning off after no user interaction is detected.
Eco Solution
Brightness Limit
Energy Saving Mode
Eco Sensor
Screen Lamp Schedule
No Signal Power Off
Auto Power Off
Minimum Backlight
On
Off
Off
Off
15 minutes
Off (Recommended)
0
The displayed image may differ depending on the model.
153
Fan and Temperature
MENU mSystemFan and TemperatureENTER E
Fan and Temperature
Fan Control
Fan Speed Setting
Outdoor Mode
Auto
100
Off
The displayed image may differ depending on the model.
It sets items related to the speed and temperature of the fan in each set.
Fan Control
Selects auto or manual for the fan speed settings.
Auto / Manual
Fan Speed Setting
Sets the fan speed within a range of 1 and 100.
Enabled when Fan Control is set to Manual.
Outdoor Mode
To use the product at a low temperature below 0 °C, make sure to set Outdoor Mode to "On".
This feature keeps the internal temperature of the product steady so that the product can start properly when it is powered on.
Off / On
Do not disconnect the power cable when this feature is set to "On".
The product consumes more power when it is turned off if this feature is set to "On" rather than to "Off".
154
Play via
MENU mSystemPlay viaENTER E
System
Play via MagicInfo
The displayed image may differ depending on the model.
Select the appropriate Play via mode depending on the environment where you are using the product.
The home screen may be different depending on the setting.
MagicInfo / URL Launcher
Change PIN
MENU mSystemChange PINENTER E
System
Change PIN
The displayed image may differ depending on the model.
Change your 4-digit Personal Identification Number (PIN).
Choose any 4 digits for your PIN and enter it in Enter a new PIN.. Reenter the same 4 digits in Enter the PIN again..
The product has memorised your new PIN.
The default PIN number is "0-0-0-0".
Change the PIN to keep your device secure.
155
Security
MENU mSystemSecurityENTER E
Security
Safety Lock On
USB Auto Play Lock
Remote Management
Secured Protocol
Network Lock
USB Lock
On
Off
Allow
Off
Off
Off
Power On Button
The displayed image may differ depending on the model.
Safety Lock On
Enter your 4 digit PIN number. The default PIN number is "0-0-0-0".
If you want to change the PIN number, use the Change PIN function.
Change the PIN to keep your device secure.
Turn Safety Lock On on or off. Safety Lock On restricts the actions that can be carried out by the remote control. The correct PIN
must be entered to turn Safety Lock On off.
Power On Button
Turn on this feature to enable the remote control's Power button to turn on the product while Safety Lock On is enabled.
Off / On
156
USB Auto Play Lock
Select whether to automatically play MagicInfo content saved on a connected USB device.
Your content should be a Published Content that is authored by using MagicInfo Premium application
and published to the USB device you are using. The MagicInfo Premium application programme is available
on the website. (http://displaysolutions.samsung.com)
When published to a USB device, your Published Content is saved to Contents and Schedules folders in
the root folder of the connected USB device.
Off
Play MagicInfo content saved on the USB device automatically.
On
Do not play MagicInfo content saved on the USB device automatically.
Connecting a USB device containing MagicInfo content displays "USB Auto Play Lock : On" for five seconds.
Remote Management
You can Allow or Deny external commands to access your product via a network.
Deny / Allow
Secured Protocol
Secure the protocol between this device and other devices.
Off / On
Network Lock
Block external network access. You can register networks on the server to allow access.
Off / On
USB Lock
Block connection to external USB ports.
Off / On
157
General
MENU mSystemGeneralENTER E
General
Smart Security
Anynet+ (HDMI-CEC)
HDMI Hot Plug
Custom Logo
Game Mode
Empty Storage
On
Off
The displayed image may differ depending on the model.
Smart Security
The security provided to protect your display device and connected storage devices against viruses includes.
Scan
Inspect your display device and connected storage devices to check for viruses.
Isolated List
This is the list of items that have been Isolated for containing viruses.
Anynet+ (HDMI-CEC)
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung
product remote control. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure
your Samsung device has this feature, check if there is an Anynet+ logo on it.
Off ( ) / On ( )
You can only control Anynet+ devices using the product remote control, not the buttons on the product.
The product remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
Anynet+ works when the AV device supporting Anynet+ is in the standby or on status.
Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
158
Troubleshooting for Anynet+
Problem Possible Solution
Anynet+ does not work. Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
Check if the Anynet+ device power cord is properly connected.
Check the Anynet+ device’s Video/Audio/HDMI cable connections.
Check whether Anynet+ (HDMI-CEC) is set to On in the System menu.
Check whether the remote control is Anynet+ compatible.
Anynet+ doesn’t work in certain situations. (initial setup)
If you have removed and then reconnected the HDMI cable, please make sure to search devices again or turn your product off
and on again.
Check if the Anynet+ function of the Anynet device is set on.
I want to start Anynet+. Check if the Anynet+ device is properly connected to the product and check if the Anynet+ (HDMI-CEC) is set to On in the
System menu.
I want to exit Anynet+. Press the SOURCE button on the product remote control and select a non- Anynet+ device.
The message “Disconnecting
Anynet+ device ...” appears on
the screen.
You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
Use the remote control after the product has completed Anynet+ configuration or has finished switching to Anynet+.
The Anynet+ device does not
play.
You cannot use the play function when initial setup is in progress.
The connected device is not
displayed.
Check whether or not the device supports Anynet+ functions.
Check whether or not the HDMI cable is properly connected.
Check whether Anynet+ (HDMI-CEC) is set to On in the System menu.
Search Anynet+ devices again.
Anynet+ requires an HDMI connection. Make sure the device is connected to your product with an HDMI cable.
Some HDMI cables may not support Anynet+ functions.
If the connection is terminated because there has been a power failure or the HDMI cable has been disconnected, please repeat
the device scan.
159
HDMI Hot Plug
This feature is used to activate the time delay to turn on a DVI/HDMI source device.
Off / On
Custom Logo
You can download, select, and set the display time of a custom logo that appears when the product turns on.
Custom Logo
You can select a custom logo (image/video) or turn off the custom logo display.
You must download the custom logo from an external USB device to set the custom logo.
Logo Display Time
If the type of custom logo is Image, you can set the Logo Display Time.
Download Logo File
You can download a custom logo into the product from an external USB device.
The file name of the custom logo you want to download must be saved as “samsung” in all small letters.
When there are multiple numbers of external USB connections, the product will attempt to download the custom logo from the
last device that has been connected to the product.
Custom logo file restrictions
Images up to 50 MB in size can be used.
Supported image file: samsung_image.*
Supported file extensions: jpg, jpeg, bmp, png
Videos up to 150 MB in size can be used. The recommendation is under 20 seconds in length.
Supported video file: samsung_video.*
Supported file extensions: avi, mpg, mpeg, mp4, ts, wmv, asf
General
Smart Security
Anynet+ (HDMI-CEC)
HDMI Hot Plug
Custom Logo
Game Mode
Empty Storage
On
Off
The displayed image may differ depending on the model.
160
General
Smart Security
Anynet+ (HDMI-CEC)
HDMI Hot Plug
Custom Logo
Game Mode
Empty Storage
On
Off
The displayed image may differ depending on the model.
Game Mode
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by
selecting game mode.
Off ( ) / On ( )
If you connect other external devices while Game Mode is on, the screen may not be in good condition.
Empty Storage
Delete files to make space for new content. Recently played files will not be deleted.
Reset System
MENU mSystemReset SystemENTER E
System
Reset System
The displayed image may differ depending on the model.
Reset all system settings to default.
161
Support (applies to the LH55OHFPSBC model only)
Software Update
MENU mSupportSoftware UpdateENTER E
The Software Update menu lets you upgrade your product software to the latest version.
Be careful not to turn off the power until the upgrade is complete. The product will turn off and on
automatically after completing the software upgrade.
When you upgrade software, all video and audio settings you have made will return to their default settings.
We advise you to write down your settings so that you can easily reset them after the upgrade.
Update Now
Update the software to the latest version.
Current version: This is the software version already installed in the product.
Contact Samsung
MENU mSupportContact SamsungENTER E
You can view the address of the Samsung website, the call centre phone number, your product's model
number, software version, Open Source Licence and other information.
Go to Contact Samsung and find the product Model Code and Software Version.
Terms & Conditions
MENU mSupportTerms & ConditionsENTER E
View and set the privacy policy for MagicInfo and other services.
Make sure that the product is connected to the network.
Reset All
MENU mSupportReset AllENTER E
This option returns all the current settings for a display to the default factory settings.
Chapter 16
162
Troubleshooting Guide
Requirements Before Contacting Samsung Customer Service Centre
– Before calling Samsung Customer
Service Centre, test your product
as follows. If the problem persists,
contact Samsung Customer Service
Centre.
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen remains blank while the Power LED / Remote sensor blinks even when the product is correctly connected to a PC, perform product testing.
1 Power off both the PC and product.
2 Disconnect all the cables from the product.
3 Power on the product.
4 If No Cable Connected is displayed, the product is operating normally.
Checking the Resolution and Frequency
Not Optimum Mode will briefly be displayed if a mode that exceeds a supported resolution is selected (refer to Supported Preset Timing Modes).
– If the screen remains blank, check the
PC system, video controller and cable.
Chapter 17
163
Check the followings.
Installation issue (PC mode)
The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connection is secure.
Blank spaces are found on all four sides of the screen when an
HDMI or HDMI-DVI cable is connected to the product and PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the
screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the graphics
card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust the
screen settings.)
Screen issue
No Signal is displayed on the screen. Check that the product is connected correctly with a cable.
Check that the device connected to the product is powered on.
Not Optimum Mode is displayed. This message is displayed when a signal from the graphics card exceeds the product's maximum
resolution and frequency.
Supported Preset Timing Modes Table and set the maximum resolution and frequency according to the
product specifications.
The images on the screen look distorted. Check the cable connection to the product.
The screen is not clear. The screen is blurry. Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky. Check that the resolution and frequency of the PC and graphics card are set within a range compatible
with the product. Then, change the screen settings if required by referring to the Additional Information
on the product menu and the Standard Signal Mode Table.
There are shadows or ghost images left on the screen.
The screen is too bright. The screen is too dark. Adjust Brightness and Contrast.
Screen colour is inconsistent. Go to Picture and adjust the Colour Space settings.
White does not really look white. Go to Picture and adjust the White Balance settings.
164
Screen issue
There is no image on the screen and the Power LED / Remote
sensor blinks every 0.5 to 1 second.
The product is in power-saving mode.
Press any key on the keyboard or move the mouse to return to the previous screen.
The product will turn off automatically. Go to System and make sure Sleep Timer is set to Off.
If a PC is connected to the product, check the power status of the PC.
Make sure the power cable is connected properly to the product and power outlet.
If the signal from a connected device is not detected, the product automatically turns off after 10 to 15
minutes.
Picture quality of the product is different from the dealer shop
where it was purchased.
Use an HDMI cable to obtain high-definition (HD) picture quality.
The screen display does not look normal. Encoded video content may cause the display to appear corrupted in scenes featuring fast moving objects
such as in a sports event or action video.
Low signal level or low picture quality may cause the display to appear corrupted. This does not mean the
product is defective.
A cell phone within a distance of one-meter radius may cause static on analogue and digital products.
The brightness and colour do not look normal. Go to Picture and adjust the screen settings such as Colour Temperature, Brightness and Sharpness.
Go to System and adjust the Energy Saving Mode settings.
Reset the screen settings to the default settings.
Lines (red, green or blue) are displayed on the screen. These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the monitor. Contact a
Samsung Service Centre to resolve the issue.
The display looks unstable and then freezes. The screen may freeze when a resolution other than the recommended resolution is used or if the signal
is not stable. To resolve the issue, change the PC resolution to the recommended resolution.
The screen cannot be displayed in full screen.
A video with an aspect ratio different from the product can cause black bars at the top and bottom of the
screen.
Change the screen size setting to full screen on the product or source device.
165
Remote control issue
The remote control does not work. Make sure that the batteries are correctly in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs switched on in the vicinity.
Source device issue
A beeping sound is heard when my PC is booting. If a beeping sound is heard when your PC is booting, have your PC serviced.
Other issue
The product smells like plastic. The plastic smell is normal and disappears over time.
Audio or video cuts out intermittently. Check the cable connection and connect it again if required.
Using a very hard or thick cable may corrupt audio and video files.
Make sure cables are flexible enough to ensure durability. When mounting the product onto a wall, it is
recommended to use right-angle cables.
Small particles are found on the edges of the product. The particles are part of the product design. The product is not defective.
When I try to change the PC resolution, a message The defined
resolution is not supported. appears.
The message The defined resolution is not supported. appears if the input source resolution exceeds the
maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.
HDMI Black Level is not functioning properly on an HDMI device
with YCbCr output.
This function is available only when a source device, such as a DVD player and STB, is connected to the
product via an HDMI (RGB signal) cable.
There is no sound in HDMI mode. Displayed picture colours may not look normal. Video or sound may not be available. This can occur if a
source device that only supports an older version of the HDMI standard is connected to the product.
166
Other issue
The IR sensor is not functioning. Make sure the sensor light turns on when a button is pressed on the remote control.
If the sensor light does not turn on, turn the power switch off and then on again on the back of the
product.
(The Power LED / Remote sensor lights up red when the screen is switched off.)
If the sensor light still does not turn on after the power switch is turned off and then on again, an internal
jack may be disconnected.
Contact your nearest service centre to have the product serviced.
If the sensor light that is on does not flash red when a button is pressed on the remote control, the IR
sensor may be defective.
Contact your nearest service centre to have the product serviced.
This function is available only when a source device, such as a DVD player and STB, is connected to
the product via an HDMI (RGB signal) cable.
167
Q & A
Question Answer
How can I change the frequency? Set the frequency on your graphics card.
Windows XP: Go to Control PanelAppearance and ThemesDisplaySettingsAdvanced
Monitor and adjust the frequency in Monitor Settings.
Windows ME/2000: Go to Control PanelDisplaySettingsAdvancedMonitor and adjust the
frequency in Monitor Settings.
Windows Vista: Go to Control PanelAppearance and PersonalizationPersonalizeDisplay
SettingsAdvanced SettingsMonitor and adjust the frequency in Monitor Settings.
Windows 7: Go to Control PanelAppearance and PersonalizationDisplayAdjust resolution
Advanced SettingsMonitor and adjust the frequency in Monitor Settings.
Windows 8: Go to SettingsControl PanelAppearance and PersonalizationDisplayAdjust
resolutionAdvanced SettingsMonitor and adjust the frequency in Monitor Settings.
Windows 10: Go to SettingsSystemDisplayAdvanced display settingsDisplay adapter
propertiesMonitor, and adjust Screen refresh rate under Monitor settings.
How can I change the resolution? Windows XP: Go to Control PanelAppearance and ThemesDisplaySettings and adjust the
resolution.
Windows ME/2000: Go to Control PanelDisplaySettings and adjust the resolution.
Windows Vista: Go to Control PanelAppearance and PersonalizationPersonalizeDisplay
Settings and adjust the resolution.
Windows 7: Go to Control PanelAppearance and PersonalizationDisplayAdjust Resolution
and adjust the resolution.
Windows 8: Go to SettingsControl PanelAppearance and PersonalizationDisplayAdjust
Resolution and adjust the resolution.
Windows 10: Go to SettingsSystemDisplayAdvanced display settings, and adjust the
resolution.
– Refer to the user manual for your PC or
graphics card for further instructions
on adjustment.
168
Question Answer
How do I set powersaving mode? Windows XP: Set power-saving mode in Control PanelAppearance and ThemesDisplayScreen
Saver Settings or BIOS SETUP on the PC.
Windows ME/2000: Set power-saving mode in Control PanelDisplayScreen Saver Settings or
BIOS SETUP on the PC.
Windows Vista: Set power-saving mode in Control PanelAppearance and Personalization
Personalize Screen Saver Settings or BIOS SETUP on the PC.
Windows 7: Set power-saving mode in Control PanelAppearance and Personalization
PersonalizeScreen Saver Settings or BIOS SETUP on the PC.
Windows 8: Set power-saving mode in SettingsControl PanelAppearance and Personalization
PersonalizeScreen Saver Settings or BIOS SETUP on the PC.
Windows 10: Set power-saving mode in SettingsPersonalizationLock screenScreen timeout
settingsPower & sleep or BIOS SETUP on the PC.
169
Specifications
– Size
– Display area
H
V
General
Model Name OH46F OH55F
Panel Size 46 CLASS (45.9 inches / 116 cm) 55 CLASS (54.6 inches / 138 cm)
Display area 1018.08 mm (H) x 572.67 mm (V) / 40.1 inches (H) x 22.5 inches (V) 1209.6 mm (H) x 680.4 mm (V) / 47.6 inches (H) x 26.8 inches (V)
Power Supply AC100-240V~ 50/60Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Environmental
considerations
Operating Temperature : -3050-22122
* For installing the enclosure, keep the internal temperature at 40 °C or below.
Humidity : 10% - 80%, non-condensing
Storage Temperature : -2045-4113
Humidity : 5% - 95%, non-condensing
Chapter 18
170
Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimises the monitor settings. Monitor installation takes place
automatically. However, you can customise the installation settings if desired.
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect product performance.
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
For detailed device specifications, visit the Samsung website.
(Europe only)
To access the EPREL registration of the model: OH46F / OH55F
(1) Go to https://eprel.ec.europa.eu
(2) Get the model identifier from the energy label of the product and type it in the search box
(3) Energy Labelling information of the model is shown
* You can directly access the product information via https://eprel.ec.europa.eu/qr/##### (registration no.)
The registration no. can be found on the rating label on your product.
(Turkey only)
To access the energy labelling information of the model: OH46F / OH55F
(1) Go to https://www.samsung.com/global/ecodesign_energy
(2) Get the model identifier from the energy label of the product and type it in the search box
(3) Energy labelling information can be found
171
Preset Timing Modes
This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified
resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.
Model Name OH46F / OH55F
Synchronization Horizontal Frequency 26 – 136 kHz
Vertical Frequency 24 – 75 Hz
Resolution Optimum Resolution 1920 x 1080 @ 60 Hz
Maximum Resolution 1920 x 1080 @ 60 Hz
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the
PC does not belong to the standard signal modes, the screen may be blank with the Power LED / Remote sensor on. In such a case, change the settings according to the
following table by referring to the graphics card user manual.
Resolution Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
MAC, 1152 x 870 68.681 75.062 100.000 -/-
VESA, 640 x 480 31.469 59.940 25.175 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 800 x 600 37.879 60.317 40.000 +/+
– Horizontal Frequency
The time required to scan a single line
from the left to the right side of the
screen is called a horizontal cycle.
The reciprocal number of a horizontal
cycle is called horizontal frequency.
Horizontal frequency is measured in
kHz.
– Vertical Frequency
The product displays a single image
multiple times per second (like a
the viewer sees. The rate of a single
image being displayed repeatedly per
second is called vertical frequency
or refresh rate. Vertical frequency is
measured in Hz.
172
Resolution Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA, 1152 x 864 67.500 75.000 108.000 +/+
VESA, 1280 x 720 45.000 60.000 74.250 +/+
VESA, 1280 x 800 49.702 59.810 83.500 -/+
VESA, 1280 x 1024 63.981 60.020 108.000 +/+
VESA, 1280 x 1024 79.976 75.025 135.000 +/+
VESA, 1366 x 768 47.712 59.790 85.500 +/+
VESA, 1440 x 900 55.935 59.887 106.500 -/+
VESA(RB), 1600 x 900 60.000 60.000 108.000 +/+
VESA, 1680 x 1050 65.290 59.954 146.250 -/+
VESA, 1920 x 1080 67.500 60.000 148.500 +/+
173
Responsibility for the Pay Service (Cost to
Customers)
When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician
in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
If a service technician gives instructions on how to use product or simply adjusts options without
disassembling product.
If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
If a product is reinstalled or devices are connected additionally after installing the purchased product
for the first time.
If a product is reinstalled to move to a different spot or to move to a different house.
If customer requests instructions on how to use because of another company's product.
If customer requests instructions on how to use the network or another company's programme.
If customer requests software installation and setup for the product.
If a service technician removes/cleans dusts or foreign materials inside of the product.
If customer requests an installation additionally after purchasing a product through home-shopping
or online.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
External impact or drop.
Use of supplies or separately sold product unspecified by Samsung.
Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
Remodeling or repairing the product by customer.
Using it with incorrect voltage or non-authorised electrical connections.
Not following the "cautions" in User Manual.
Others
If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp,
Filter, Ribbon, etc.)
If customer requests a service in case the product has no defect, service fee may be charged. So please read
User Manual first.
Appendix
Chapter 19
174
Optimum Picture Quality and Afterimage
Burn-in Prevention
Optimum Picture Quality
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may
be brighter or darker on the panel. This does not affect product performance.
The number of sub-pixels by panel type: 6,220,800
Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage
burn-in or defective pixels.
Activate power-saving mode or a dynamic screen saver if you will not be using the product for an
extended period of time.
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers
to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period
of time, a slight voltage difference may occur between the electrodes in pixels that control the liquid
crystals.
Such a voltage difference between electrodes increases with time and makes the liquid crystals thinner.
When this occurs, a previous image can remain on the screen when the pattern changes. To prevent this,
the accumulated voltage difference should be reduced.
Afterimage burn-in should not occur when an LCD panel is operating in proper conditions.
Black Matrix
Source Drain
Data Bus-Line
TFT
Gate Pixel Electrode (ITO) Storage
Capaccitor (Cs)
Colour-Filter
Common
Electrode (ITO)
175
Preventing afterimage burn-in
The best way to protect the product from afterimage burn-in is switching the power off or setting the PC or
system to run a screen saver when not in use. Also, Warranty service may be limited depending on instruction
guide.
Powering Off, Screen Saver and Power Saving Mode
Power off the product for 2 hours after using it for 12 hours.
Go to Display Properties > Power Supply on your PC and set the product to power off as required.
Using a screen saver is recommended.
It is best to use a single-colour or moving-image screen saver.
Regular colour Change
Use 2 colours
Switch between 2 colours every 30 minutes as shown above.
FLIGHT FLIGHT
TIME TIME
OZ348
UA102 21:10
20:30
OZ348
UA102 21:10
20:30
Type 1 Type 2
Avoid combinations of a text colour and background colour of contrasting brightness.
(Brightness: refers to the lightness or darkness of a colour which varies depending on the amount of
light emitted.)
Avoid using grey as it may contribute to afterimage burn-in.
Avoid using colours of contrasting brightness (black and white; grey).
FLIGHT TIME
OZ348 20:30
:
:
FLIGHT TIME
OZ348 20:30
:
:
Regular Text colour Change
Use bright colours of similar brightness.
Interval: Change text colour and background colour every 30 minutes
FLIGHT TIME
OZ348 20:30
:
:
FLIGHT TIME
OZ348 20:30
:
:
FLIGHT TIME
OZ348 20:30
:
:
FLIGHT TIME
OZ348 20:30
:
:
Move and change text every 30 minutes as shown below.
FLIGHT TIME
OZ348 20:30
:
:
[ Step 3 ]
[ Step 2 ]
FLIGHT TIME
OZ348
:
:
[ Step 1 ]
20:30
Regularly display a moving image along with a logo.
Interval: Display a moving image along with a logo for 60 seconds after using for 4 hours.
176
Licence
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the product menu.
Open Source Licence Notice is written only English.
For information on the Open Source Licence Notice, contact the Samsung Customer Centre or send
email to oss.request@samsung.com.
177
Terminology
480i / 480p / 720p / 1080i /
1080p____ Each of the scanning
rates above refers to the number of
effective scanning lines that decides
the screen resolution. The scanning
rate may be indicated in i (interlaced)
or p (progressive), depending on the
scanning method.
- Scanning
Scanning refers to a process of
sending pixels that form an image
progressively. A larger number of
pixels will deliver a clearer and more
vivid picture.
- Progressive
In progressive scan mode, all lines
of pixels are scanned one by one
(progressively) on the screen.
- Interlaced
In interlaced scan mode, every other
line of pixels is scanned from top to
bottom first and then the remaining
lines of pixels (that were not scanned)
are scanned.
Non-interlace Mode and Interlace
Mode____ Non-interlace mode
(progressive scan) displays a
horizontal line from the top to the
bottom of a screen progressively.
Interlace mode displays the odd
number lines first and the even
number lines next. Non-interlace
mode is mainly used in monitors as it
produces screen clarity and interlace
mode is mainly used in TVs.
Dot Pitch____ The screen consist of
red, green and blue dots. A shorter
distance between the dots produces
a higher resolution. Dot pitch refers
to the distance between the shortest
distance between dots of the same
colour. Dot pitch is measured in
millimetres.
Vertical Frequency____ The product
displays a single image many times
per second (like a fluorescent light
that flickers) to display an image for
a viewer to see. The rate of a single
image being displayed repeatedly per
second is called vertical frequency
or refresh rate. Vertical frequency is
measured in Hz.
E.g. 60Hz refers to a single image
being displayed 60 times in one
second.
Horizontal Frequency____ The
time required to scan a single line
from the left to the right side of the
screen is called a horizontal cycle.
The reciprocal number of a horizontal
cycle is called horizontal frequency.
Horizontal frequency is measured in
kHz.
Source____ Input source refers to a
video source device connected to the
product such as a camcorder or video
or DVD player.
Plug & Play____ Plug & Play is a
function that allows the automatic
exchange of information between
a monitor and PC to produce an
optimum display environment. The
product uses VESA DDC (international
standard) to execute Plug & Play.
Resolution____ Resolution is the
number of horizontal dots (pixels)
and vertical dots (pixels) that form
a screen. It represents the level of
display detail. A higher resolution
enables more data to be displayed on
the screen and is useful to perform
multiple tasks simultaneously.
E.g. A resolution of 1920 X 1080
consists of 1,920 horizontal pixels
(horizontal resolution) and 1,080
vertical pixels (vertical resolution).
DVD (Digital Versatile Disc)____ DVD
refers to a CD-sized mass storage
disk where you can save multimedia
(audio, video or game) applications
using MPEG-2 video compression
technology.
HDMI (High Definition Multimedia
Interface)____ It is an interface that
can be connected to a digital audio
source as well as a high-definition
video source by using a single cable
without compression.
Multiple Display Control (MDC)____
MDC (Multiple Display Control) is
an application that allows multiple
display devices to be controlled
simultaneously using a PC.
Communication between a PC and
monitor takes place using RS232C
(serial data transmission) and RJ45
(LAN) cables.