Samsung LH75EDEPLGC User Manual
Displayed below is the user manual for LH75EDEPLGC by Samsung which is a product in the Signage Displays category. This manual has pages.
Related Manuals
User Manual
The colour and the appearance may differ depending on the product, and the
specifications are subject to change without prior notice to improve the performance.
Recommended hours of use per day for the EDE, EME, DCE models is less than 16 hours.
If the product is used for longer than 16 hours a day, the warranty may be void.
ED65E ED75E
EM65E EM75E
DC32E DC40E DC48E DC55E
DC32E-M DC40E-M DC48E-M DC55E-M
DC40E-H DC48E-H
Table of contents
Before Using the Product
Copyright 6
Safety Precautions 7
Symbols 7
Cleaning 7
Storage 8
Electricity and Safety 8
Installation 9
Operation 11
Preparations
Checking the Components 14
Components 14
Parts 15
Control Panel 15
Reverse Side 17
Reverse Side 18
Anti-theft Lock 19
Remote Control 20
Before Installing the Product
(Installation Guide) 22
Switching between portrait and landscape 22
Ventilation 22
Installing the Wall Mount 23
Preparing before installing Wall-Mount 23
Installing the Wall Mount Kit 23
Wall Mount Kit Specifications (VESA) 24
Remote Control (RS232C) 25
Cable Connection 25
Connection 28
Control Codes 29
Connecting and Using a Source
Device
Before Connecting 38
Pre-connection Checkpoints 38
Connecting to a PC 38
Connection using the D-SUB cable
(Analogue type) 38
Connection using a DVI cable (Digital type) 39
Connection Using an HDMI-DVI Cable 39
Connection Using an HDMI Cable 40
Connecting to a Video Device 41
Connection Using the AV Cable 41
Connection Using the component Cable 41
Connection Using an HDMI-DVI Cable 42
Connection Using an HDMI Cable 43
Connecting to an Audio System 43
Connecting the LAN Cable 44
Connecting the HDBase-T 45
Changing the Input source 46
Source 46
Using MDC
MDC Programme Installation/Uninstallation 47
Installation 47
Uninstallation 47
Connecting to MDC 48
Using MDC via RS-232C
(serial data communications standards) 48
Using MDC via Ethernet 49
Screen Adjustment
Picture Mode 50
If the input source is PC, DVI, HDMI(PC) 50
If the input source is AV, Component, HDMI(AV ) 50
Backlight / Contrast / Brightness / Sharpness /
Colour / Tint (G/R) 51
Gamma 51
Calibrated value 52
Picture Size 53
Picture Size 53
Position 54
Zoom/Position 54
Resolution Select 55
Auto Adjustment 55
PC Screen Adjustment 56
PIP 57
2
Table of contents
Advanced Settings 58
Dynamic Contrast 59
Black Tone 59
Flesh Tone 59
RGB Only Mode 59
Colour Space 59
White Balance 59
Motion Lighting 59
Picture Options 60
Colour Tone 61
Colour Temp. 61
Digital Clean View 61
MPEG Noise Filter 61
HDMI Black Level 62
Film Mode 62
Motion Plus 62
Dynamic Backlight 62
Picture Off 63
Reset Picture 63
Sound Adjustment
Sound Mode 64
Sound Effect 65
Speaker Settings 66
Reset Sound 66
Network
Network Status 67
Network Settings 67
Network type 67
Network Settings (Wired) 68
Network Setting (Wireless) 70
WPS(PBC) 72
Wi-Fi Direct 73
AllShare Settings 73
Server Network Settings 74
Connect to server 74
Server Access 74
FTP Mode 74
Device Name 74
Applications
Source List 75
Refresh 75
Edit Name 75
Information 75
MagicInfo Lite 76
Playing content from the internal memory or
USB 76
Network Channel 77
System
Setup 79
Menu Language 80
Multi Control 80
Configuring settings for Multi Control 80
Time 81
Clock Set 81
Sleep Timer 81
On Timer 81
Off Timer 82
Holiday Management 82
Eco Solution 83
Energy Saving 83
Eco Sensor 83
No Signal Power Off 83
Auto Power Off 83
Auto Protection Time 84
Screen Burn Protection 85
Pixel Shift 85
Timer 86
Immediate display 87
Side Grey 87
Ticker 88
Video Wall 89
Video Wall 89
Format 89
Horizontal 89
3
Table of contents
Vertical 90
Screen Position 90
Source AutoSwitch Settings 91
Source AutoSwitch 91
Primary Source Recovery 91
Primary Source 91
Secondary Source 91
Change PIN 92
General 93
Max. Power Saving 93
Game Mode 93
Auto Power On 93
Safety Lock 93
Button Lock 94
Standby Control 94
HDBT Standby 94
Network Standby 94
Lamp Schedule 95
OSD Display 95
Power On Adjustment 95
Temperature Control 95
Anynet+ (HDMI-CEC) 96
Anynet+ (HDMI-CEC) 96
Auto Turn Off 97
Troubleshooting for Anynet+ 98
Clone Product 100
Reset System 100
Reset All 101
DivX® Video On Demand 101
PC module power 101
Synced power-on 101
Synced power-off 101
Support
Software Update 102
Update now 102
Contact Samsung 102
Playing photos, videos and music
(Media Play)
Read the following before using media play
with a USB device 103
Using a USB device 105
Menu items in the media content list page 106
Available buttons and features during photo
playback 107
Available buttons and features during video
playback 108
Available buttons and features during music
playback 109
Supported Subtitle and Media play file
formats 110
Subtitle 110
Compatible image file format 110
Supported music file formats 111
Supported Video Formats 111
Troubleshooting Guide
Requirements Before Contacting Samsung
Customer Service Centre 114
Testing the Product 114
Checking the Resolution and Frequency 114
Check the followings. 115
Q & A 122
Specifications
General 123
Preset Timing Modes 125
4
Table of contents
Appendix
Responsibility for the Pay Service
(Cost to Customers) 127
Not a product defect 127
A Product damage caused by customer's fault 127
Others 127
Optimum Picture Quality and Afterimage
Burn-in Prevention 128
Optimum Picture Quality 128
Prevention of Afterimage Burn-in 128
Licence 130
Terminology 131
5
6
Before Using the Product
Chapter 01
Copyright
The contents of this manual are subject to change without notice to improve quality.
© 2016 Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Microsoft, Windows are registered trademarks of Microsoft Corporation.
VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Ownership of all other trademarks is attributed to their due owner.
•An administration fee may be charged if either
-(a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual).
-(b) you bring the unit to a repair centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
•The amount of such administration charge will be advised to you before any work or home visit is carried out.
7
Safety Precautions
Caution
RISK OF ELECTRIC SHOCK DO NOT OPEN
Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. (OR BACK)
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
REFER ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that high voltage is present inside.
It is dangerous to make any kind of contact with any internal part of this product.
This symbol alerts you that important literature concerning operation and maintenance has been
included with this product.
Symbols
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are not followed.
Activities marked by this symbol are prohibited.
Instructions marked by this symbol must be followed.
Cleaning
―Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
―Take the following steps when cleaning.
―The following images are for reference only. Real-life situations may differ from what is shown in the
images.
1
Power off the product and computer.
2
Disconnect the power cord from the product.
―Hold the power cable by the plug and do not touch the cable with wet
hands. Otherwise, an electric shock may result.
!
3
Wipe the product with a clean, soft and dry cloth.
•Do not use detergents that contain alcohol, solvent or
surface-active agents.
•Do not spray water or detergent directly on the product.
4
Wet a soft and dry cloth in water and wring thoroughly to clean the
exterior of the product.
5
Connect the power cord to the product when cleaning is finished.
6
Power on the product and computer.
8
Storage
Due to the characteristics of high-glossy products, using a UV humidifier nearby may create
whitecoloured stains on the product.
―Contact Customer Service Centre if the inside of the product needs cleaning (service fee will be
charged).
Electricity and Safety
―The following images are for reference only. Real-life situations may differ from what is shown in the
images.
Warning
Do not use a damaged power cord or plug, or a loose power socket.
•An electric shock or fire may result.
Do not use multiple products with a single power socket.
•Overheated power sockets may cause a fire.
Do not touch the power plug with wet hands. Otherwise, an electric shock
may result.
!
Insert the power plug all the way in so it is not loose.
•An unsecure connection may cause a fire.
!
Connect the power plug to a grounded power socket (type 1 insulated
devices only).
•An electric shock or injury may result.
Do not bend or pull the power cord with force. Be careful not to leave the
power cord under a heavy object.
•Damage to the cord may result in a fire or electric shock.
Do not place the power cord or product near heat sources.
•A fire or electric shock may result.
!
Clean any dust around the pins of the power plug or the power socket with
a dry cloth.
•A fire may result.
9
Caution
Do not disconnect the power cord while the product is being used.
•The product may become damaged by an electric shock.
!
Only use the power cord provided with your product by Samsung. Do not
use the power cord with other products.
•A fire or electric shock may result.
!
Keep the power socket where the power cord is connected unobstructed.
•The power cord must be disconnected to cut off power to the product
when an issue occurs.
•Note that the product is not completely powered down by using only
the power button on the remote.
!
Hold the plug when disconnecting the power cord from the power socket.
•An electric shock or fire may result.
Installation
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF
THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
•A fire may result.
!
Have a technician install the wall-mount hanger.
•Installation by an unqualified person can result in an injury.
•Only use approved cabinets.
Do not install the product in poorly ventilated spaces such as a bookcase or
closet.
•An increased internal temperature may cause a fire.
!
Install the product at least 10cm away from the wall to allow ventilation.
•An increased internal temperature may cause a fire.
!
Keep the plastic packaging out of the reach of children.
•Children may suffocate.
10
Do not install the product on an unstable or vibrating surface (insecure shelf,
sloped surface, etc.)
•The product may fall and become damaged and/or cause an injury.
•Using the product in an area with excess vibration may damage the
product or cause a fire.
!
Do not install the product in a vehicle or a place exposed to dust, moisture
(water drips, etc.), oil, or smoke.
•A fire or electric shock may result.
Do not expose the product to direct sunlight, heat, or a hot object such as a
stove.
•The product lifespan may be reduced or a fire may result.
Do not install the product within the reach of young children.
•The product may fall and injure children.
•As the front is heavy, install the product on a flat and stable surface.
Edible oil, such as soybean oil, can damage or deform the product. Do not
install the product in a kitchen or near a kitchen counter.
Caution
!
Do not drop the product while moving.
•Product failure or personal injury may result.
Do not set down the product on its front.
•The screen may become damaged.
When installing the product on a cabinet or shelf, make sure that the
bottom edge of the front of the product is not protruding.
•The product may fall and become damaged and/or cause an injury.
•Install the product only on cabinets or shelves of the right size.
!
Set down the product gently.
•Product failure or personal injury may result.
SAMSUNG
!
Installing the product in an unusual place (a place exposed to a lot of fine
dust, chemical substances, extreme temperatures or a significant presence
of moisture, or a place where the product will operate continuously for an
extended period of time) may seriously affect its performance.
•Be sure to consult Samsung Customer Service Centre if you want to
install the product at such a place.
11
Operation
Warning
There is a high voltage inside the product. Never disassemble, repair or
modify the product yourself.
•A fire or electric shock may result.
•Contact Samsung Customer Service Centre for repairs.
!
Before moving the product, turn off the power switch and disconnect the
power cable and all other connected cables.
•Damage to the cord may result in a fire or electric shock.
!
If the product generates abnormal sounds, a burning smell or smoke,
disconnect the power cord immediately and contact Samsung Customer
Service Centre.
•An electric shock or fire may result.
Do not let children hang from the product or climb on top of it.
•Children may become injured or seriously harmed.
If the product is dropped or the outer case is damaged, turn off the power
switch and disconnect the power cord. Then contact Samsung Customer
Service Centre.
•Continued use can result in a fire or electric shock.
Do not leave heavy objects or items that children like (toys, sweets, etc.) on
top of the product.
•The product or heavy objects may fall as children try to reach for the
toys or sweets resulting in a serious injury.
!
During a lightning or thunderstorm, power off the product and remove the
power cable.
•A fire or electric shock may result.
!
Do not drop objects on the product or apply impact.
•A fire or electric shock may result.
Do not move the product by pulling the power cord or any cable.
•Product failure, an electric shock or fire may result from a damaged
cable.
!GAS
If a gas leakage is found, do not touch the product or power plug. Also,
ventilate the area immediately.
•Sparks can cause an explosion or fire.
Do not lift or move the product by pulling the power cord or any cable.
•Product failure, an electric shock or fire may result from a damaged
cable.
12
!
Do not use or keep combustible spray or an inflammable substance near
the product.
•An explosion or fire may result.
Ensure the vents are not blocked by tablecloths or curtains.
•An increased internal temperature may cause a fire.
100
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects
that burn easily (paper, matches, etc) into the product (via the vent or input/
output ports, etc).
•Be sure to power off the product and disconnect the power cord
when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Centre.
•Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic
objects on top of the product.
•Be sure to power off the product and disconnect the power cord
when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Centre.
•Product failure, an electric shock or fire may result.
Caution
!
Leaving the screen fixed on a stationary image for an extended period of
time may cause afterimage burn-in or defective pixels.
•Activate power-saving mode or a moving-picture screen saver if you
will not be using the product for an extended period of time.
-_-
!
Disconnect the power cord from the power socket if you do not plan on
using the product for an extended period of time (vacation, etc).
•Dust accumulation combined with heat can cause a fire, electric shock
or electric leakage.
!
Use the product at the recommended resolution and frequency.
•Your eyesight may deteriorate.
Do not hold the product upside-down or move it by holding the stand.
•The product may fall and become damaged or cause an injury.
!
Looking at the screen too close for an extended period of time can
deteriorate your eyesight.
Do not use humidifiers or stoves around the product.
•A fire or electric shock may result.
13
!
Rest your eyes for more than 5 minutes for every 1 hour of product use.
•Eye fatigue will be relieved.
Do not touch the screen when the product has been turned on for an
extended period of time as it will become hot.
!
Store small accessories out of the reach of children.
!
Exercise caution when adjusting the product angle or stand height.
•Your hand or finger may get stuck and injured.
•Tilting the product at an excessive angle may cause the product to fall
and an injury may result.
Do not place heavy objects on the product.
•Product failure or personal injury may result.
When using headphones or earphones, do not turn the volume too high.
•Having the sound too loud may damage your hearing.
Be careful that children do not place the battery in their mouths when
removed from the remote control. Place the battery in a location that
children or infants cannot reach.
•If children have had the battery in their mouths, consult your doctor
immediately.
When replacing the battery, insert it with the right polarity (+, -).
•Otherwise, the battery may become damaged or it may cause fire,
personal injury or damage due to leakage of the internal liquid.
!
Use only the specified standardized batteries, and do not use a new battery
and a used battery at the same time.
•Otherwise, the batteries may be damaged or cause fire, personal injury
or damage due to a leakage of the internal liquid.
!
The batteries (and rechargeable batteries) are not ordinary refuse and must
be returned for recycling purposes. The customer is responsible for returning
the used or rechargeable batteries for recycling.
•The customer can return used or rechargeable batteries to a nearby
public recycling centre or to a store selling the same type of the
battery or rechargeable battery.
14
Preparations
Chapter 02
Checking the Components
-Contact the vendor where you
purchased the product if any
components are missing.
-The pictures may look different from the
actual components.
-A stand is not provided with the product.
To install a stand, you can purchase one
separately.
-The RS232C adapter can be used to
connect to another monitor using the
D-SUB (9-pin) type RS232C cable.
Components
―Components may differ in different locations.
Quick Setup Guide Warranty card
(Not available in some locations) Regulatory guide Power cord
+
+
-
-
Batteries
(Not available in some locations) Remote Control D-SUB cable
(EDE and EME Model Only) RS232C(IN) adapter
Holder-Ring (4EA)
(EDE and EME Model Only)
15
Parts
Control Panel
DC32E DC32E-M
Panel Key
Speaker
Speaker
Spacer logo
Remote sensor
―The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to
improve quality.
Buttons Description
Power on the product.
If you press the button when the product is turned on, the control menu will be
displayed.
―To exit the OSD menu, press and hold the panel key for at least one second.
Move to the upper or lower menu. You can also adjust the value of an option.
Move to the left or right menu.
―You can adjust the volume by moving the panel key left or right when the control
menu is not displayed.
Spacer logo
(Optional)
Do not pull on the spacer logo using force. The logo may tear or break off.
Remote sensor
Press a button on the remote control pointing at the sensor on the front of the
product to perform the corresponding function.
―Using other display devices in the same space as the remote control of this
product can cause the other display devices to be inadvertently controlled.
Use the remote control within 7 m to 10 m from the sensor on the product at an angle of 30 from the left and right.
―Store used batteries out of reach of children and recycle.
―Do not use a new and used battery together. Replace both batteries at the same time.
―Remove batteries when the remote control is not to be used for an extended period of time.
16
―If you press the button on the panel key when the product is turned on, the
control menu will be displayed.
Control menu
EDE / EME
Return
DCE / DCE-M / DCE-H
Return
Buttons Description
Source
Select the connected input source.
Move the panel key right to select Source in the control menu. When the list of
input sources is displayed, move the panel key left or right to select the desired input
source. Next, press the panel key.
Menu
Display the OSD menu.
Move the panel key left to select Menu in the control menu. The OSD control
screen will appear. Move the panel key right to select the desired menu. You can
select a sub-menu item by moving the panel key up, down, left, or right. To change
settings, select the desired menu and press the panel key.
MagicInfo
Enter MagicInfo mode.
Move the panel key up to select MagicInfo in the control menu.
―DCE, DCE-M, DCE-H models are only supported.
Tools
Display Tools.
Move the panel key up to select Tools in the control menu.
―EDE, EME models are only supported.
Power o
Power off the product.
Move the panel key down to select
Power o
in the control menu. Next, press
the panel key.
Return
Exit the control menu.
17
Reverse Side
―The colour and shape of parts may differ from what is shown. Specifications are
subject to change without notice to improve quality.
―EDE, EME models are only supported.
DVI IN /
MAGICINFO IN
HDMI IN
USB
(5V, 1.5A)
HDBT IN
RGB IN RS232C IN RS232C OUT
AUDIO
OUT
RGB / DVI /
HDMI / AV /
COMPONENT
/ AUDIO IN
IR /
AMBIENT
SENSOR IN
COMPONENT IN
Port Description
HDBT IN
Sends the HDMI signal to a connected LAN cable using an HDBaseT transmitter.
―EME models are only supported.
USB (5V, 1.5A)
Connect to a USB memory device.
DVI IN / MAGICINFO IN
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box
(sold separately).
HDMI IN
Connects to a source device using an HDMI cable.
RGB IN
Connects to a source device using a D-SUB cable.
RS232C IN
Connects to MDC using an RS232C adapter.
RS232C OUT
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN
Receives sound from a PC via an audio cable.
AUDIO OUT
Connects to the audio of a source device.
AV IN / COMPONENT IN
Connects to a source device using the AV/Component adapter.
IR / AMBIENT SENSOR IN
Supplies power to the external sensor board or receives the light sensor signal.
18
Reverse Side
―The colour and shape of parts may differ from what is shown. Specifications are
subject to change without notice to improve quality.
―DCE, DCE-M, DCE-H models are only supported.
RS232C IN RGB IN RJ45
IR IN
DVI IN /
MAGICINFO IN
AUDIO OUT
HDMI IN 1
HDMI IN 2
AUDIO IN
COMPONENT IN
USB
(5V, 1.5A)
Port Description
AUDIO OUT
Connects to the audio of a source device.
AV IN / COMPONENT IN
Connects to a source device using the AV/Component adapter.
AUDIO IN
Receives sound from a PC via an audio cable.
USB (5V, 1.5A)
Connect to a USB memory device.
DVI IN / MAGICINFO IN
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box
(sold separately).
HDMI IN 1, HDMI IN 2
Connects to a source device using an HDMI cable.
IR IN
Supplies power to the external sensor board or receives the light sensor signal.
RS232C IN
Connects to MDC using an RS232C adapter.
RGB IN
Connects to a source device using a D-SUB cable.
RJ45
Connects to MDC using a LAN cable.
19
Anti-theft Lock
―An anti-theft lock allows you to use the product securely even in public places.
―The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
―The following images are for reference only. Real-life situations may differ from what is shown in the images.
To lock an anti-theft locking device:
―Stand: Sold separately
1
Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2
Put one end of the cable through the loop on the other end.
3
Insert the locking device into the anti-theft lock slot at the back of the product.
4
Lock the locking device.
-An anti-theft locking device can be purchased separately.
-Refer to the user guide provided with your anti-theft locking device for details.
-Anti-theft locking devices can be purchased at electronics retailers or online.
20
-Remote control button functions may
differ for different products.
Remote Control
―Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
―A button without a description in the image below is not supported on the product.
MENU
POWER
OFF
VOL
MagicInfo
Player I
.QZ
1
ABC
2
DEF
3
GHI
4
JKL
5
MNO
6
SYMBOL
0
PRS
7
TUV
8
WXY
9
MUTE
SOURCE
CH
DEL-/--
CH LIST
HOME
Power off the product.
Number buttons
Enter the password in the OSD menu.
Mute the sound.
Unmuting the sound: Press MUTE again or press
the volume control(+ VOL -) button.
Use this hotkey to directly access MagicInfo.
The hotkey works if the network box is
connected.
MagicInfo Launch Button.
―DCE, DCE-M, DCE-H models are only
supported.
Power on the product.
Adjust the volume.
Change the input source.
Display or hide the onscreen display menu, or
return to the previous menu.
21
TOOLS INFO
SET
UNSET
LOCK
PC
A
DVI
B
HDMI
C
DP
D
EXITRETURN
IR control
Display information about the current input
source.
Move to the upper, lower, left or right menu, or
adjust an option's setting.
Confirm a menu selection.
Exit the current menu.
Manually select a connected input source from
PC, DVI, HDMI.
It sets safe lock function.
Used in Anynet+ mode and multimedia mode.
Quickly select frequently used functions.
Return to the previous menu.
-Remote control button functions may
differ for different products.
To place batteries in the remote control
22
Before Installing the Product
(Installation Guide)
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
•Ensure that an authorized installation company installs the wall mount.
•Otherwise, it may fall and cause personal injury.
•Make sure to install the specified wall mount.
Switching between portrait and landscape
―Contact Samsung Customer Service Centre for further details.
•To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
A
B
Figure 1.1 Side view
Ventilation
Installation on a Perpendicular Wall
A Minimum 40 mm
B Ambient temperature: Under 35 C
•When installing the product on a perpendicular wall, allow at least 40 mm of space between the product and wall surface
for ventilation and ensure that the ambient A temperature is kept below 35 C.
23
A
B
C
E
Figure 1.3 Side view
D D
Figure 1.2 Side view
Installation on an Indented Wall
―Contact Samsung Customer Service Centre for further details.
Plane view
A Minimum 40 mm
B Minimum 70 mm
C Minimum 50 mm
D Minimum 50 mm
E Ambient temperature: Under 35 C
―When installing the product on an indented wall, allow at least the space specified above between the product and wall for
ventilation and ensure that the ambient temperature is kept below 35 C.
Installing the Wall Mount
1
Preparing before installing Wall-Mount
To install a wall-mount from another manufacturer, use the Holder-Ring(
1
).
―EDE, EME models are only supported.
Installing the Wall Mount Kit
The wall mount kit (sold separately) allows you to mount the product on the wall.
For detailed information on installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the
wall mount on your own.
24
Wall Mount Kit Specications (VESA)
―Install your wall mount on a solid wall perpendicular to the floor. Before
attaching the wall mount to surfaces other than plaster board, please contact
your nearest dealer for additional information.
If you install the product on a slanted wall, it may fall and result in severe
personal injury.
•Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
•Do not use screws that are longer than the standard length or do not comply with the VESA standard screw
specifications. Screws that are too long may cause damage to the inside of the product.
•For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ
depending on the wall mount specifications.
•Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
•Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the
consumer fails to follow the product installation instructions.
•Always have two people mount the product on a wall.
•Standard dimensions for wall mount kits are shown in the table below.
Unit: mm (inches)
Model name VESA screw hole specs
(A * B) in millimeters
Standard Screw Quantity
ED65E / ED75E / EM65E / EM75E
/ DC48E / DC55E / DC48E-M /
DC48E-H / DC55E-M
400 x 400 (15.7 x 15.7) M8, L32 4
DC32E / DC40E / DC32E-M /
DC40E-M / DC40E-H
200 x 200 (7.9 x 7.9)
―Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
25
Remote Control (RS232C)
Cable Connection
RS232C Cable
Interface
RS232C (9 pins)
Pin
TxD (No.2), RxD (No.3), GND (No.5)
Bit rate
9600 bps
Data bits
8 bit
Parity
None
Stop bit
1 bit
Flow control
None
Maximum length
15 m (only shielded type)
•Pin assignment
1 2 3 4 5
6 7 8 9
5 4 3 2 1
9 8 7 6
<Male type> <Female type>
Pin Signal
1
Detect data carrier
2
Received data
3
Transmitted data
4
Prepare data terminal
5
Signal ground
6
Prepare data set
7
Send request
8
Clear to send
9
Ring indicator
26
•RS232C cable
Connector: 9-Pin D-Sub to Stereo Cable
5
16
9
-P2-
1
2
3
-P1-
-P1- -P1- -P2- -P2-
Male type Rx
Tx
Gnd
3
2
5
----------
----------
----------
1
2
3
Tx
Rx
Gnd
STEREO
PLUG
(3.5ø)
LAN Cable (DCE, DCE-M, DCE-H Model Only)
•Pin assignment
12345678
Pin No Standard Colour Signal
1 White and orange TX+
2 Orange TX-
3 White and green RX+
4 Blue NC
5 White and blue NC
6 Green RX-
7 White and brown NC
8 Brown NC
27
•Connector : RJ45
Direct LAN cable (PC to HUB)
RJ45 RJ45 MDC
HUB
P1
P1P2
P2
Signal P1 P2 Signal
TX+ 1 <--------> 1 TX+
TX- 2 <--------> 2 TX-
RX+ 3 <--------> 3 RX+
RX- 6 <--------> 6 RX-
Cross LAN cable (PC to PC)
RJ45
P1 P2
Signal P1 P2 Signal
TX+ 1 <--------> 3 RX+
TX- 2 <--------> 6 RX-
RX+ 3 <--------> 1 TX+
RX- 6 <--------> 2 TX-
28
Connection
―Ensure you connect each of the adapters to the correct RS232C IN or OUT port on the product.
•Connection 1 (EDE / EME Model)
RS232C
IN OUT
RS232C
IN OUT
RS232C
IN OUT
RS232C
IN OUT
•Connection 2 (DCE / DCE-M / DCE-H Model)
RJ45 RJ45
•Connection 3 (DCE / DCE-M / DCE-H Model)
RS232C
IN
29
Control Codes
Viewing control state (Get control command)
Header Command ID Data length Checksum
0xAA Command type 0
Controlling (Set control command)
Header Command ID Data length Data Checksum
0xAA Command type 1 Value
Command
No. Command type Command Value range
1
Power control 0x11 0~1
2
Volume control 0x12 0~100
3
Input source control 0x14 -
4
Screen mode control 0x18 -
5
Screen size control 0x19 0~255
6
PIP on/off control 0x3C 0~1
7
Auto adjustment control (PC and
BNC only)
0x3D 0
8
Video wall mode control 0x5C 0~1
9
Safety Lock 0x5D 0~1
No. Command type Command Value range
10
Video Wall On 0x84 0~1
11
Video Wall User Control 0x89 -
•All communications take place in hexadecimals. The checksum is calculated by adding up all
values except the header. If a checksum adds up to be more than 2 digits as shown below
(11+FF+01+01=112), the first digit is removed.
E.g. Power On & ID=0
Header Command ID Data length Data 1 Checksum
0xAA 0x11 1 "Power"
Header Command ID Data length Data 1 12
0xAA 0x11 1 1
•To control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID as
"0xFE" and transmit commands. Commands will be executed by each device but ACK will not
respond.
30
Power control
•Function
A product can be powered on and off using a PC.
•Viewing power state (Get Power ON / OFF Status)
Header Command ID Data length Checksum
0xAA 0x11 0
•Setting power ON/Off (Set Power ON / OFF)
Header Command ID Data length Data Checksum
0xAA 0x11 1 "Power"
"Power": Power code to be set on a product.
1: Power ON
0: Power OFF
•Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x11 "Power"
"Power": Power code to be set on a product.
•Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x11 "ERR"
"ERR" : A code showing what error has occurred.
Volume control
•Function
The volume of a product can be adjusted using a PC.
•Viewing volume state (Get Volume Status)
Header Command ID Data length Checksum
0xAA 0x12 0
•Setting the volume (Set Volume)
Header Command ID Data length Data Checksum
0xAA 0x12 1 "Volume"
"Volume": Volume value code to be set on a product. (0-100)
•Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x12 "Volume"
"Volume": Volume value code to be set on a product. (0-100)
•Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x12 "ERR"
"ERR" : A code showing what error has occurred.
31
Input source control
•Function
The input source of a product can be changed using a PC.
•Viewing input source state (Get Input Source Status)
Header Command ID Data length Checksum
0xAA 0x14 0
•Setting the input source (Set Input Source)
Header Command ID Data length Data Checksum
0xAA 0x14 1 "Input Source"
"Input Source": An input source code to be set on a product.
0x14 PC
0x18 DVI
0x0C Input source
0x08 Component
0x20 MagicInfo
0x1F DVI_video
0x30 RF(TV)
0x40 DTV
0x21 HDMI1(HDMI)
0x22 HDMI1_PC(HDMI_PC)
0x23 HDMI2
0x24 HDMI2_PC
0x55 HDBT
―DVI_video, HDMI1_PC(HDMI_PC) and HDMI2_PC cannot be used with the Set command. They only
respond to "Get" commands.
―Available input sources may vary depending on the model.
―MagicInfo is only available with models that contain the MagicInfo function.
―RF(TV), DTV are only available with models that include a TV.
•Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x14 "Input
Source"
"Input Source": An input source code to be set on a product.
•Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x14 "ERR"
"ERR" : A code showing what error has occurred.
32
Screen mode control
•Function
The screen mode of a product can be changed using a PC.
Screen mode cannot be controlled when the Video Wall function is enabled.
―This control can only be used on models that include a TV.
•Viewing screen status (Get Screen Mode Status)
Header Command ID Data length Checksum
0xAA 0x18 0
•Setting the picture size (Set Picture Size)
Header Command ID Data
length
Data Checksum
0xAA 0x18 1 "Screen Mode"
"Screen Mode": A code that sets the product status
0x01 16 : 9
0x04 Zoom
0x31 Wide Zoom
0x0B 4 : 3
•Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x18 "Screen
Mode"
"Screen Mode": A code that sets the product status
•Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x18 "ERR"
"ERR": A code showing what error has occurred
Screen size control
•Function
The screen size of a product can be changed using a PC.
•Viewing the screen size (Get Screen Size Status)
Header Command ID Data length Checksum
0xAA 0x19 0
•Ack
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x19 "Screen Size"
"Screen Size": product screen size (range: 0 – 255, unit: inch)
•Nak
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x19 "ERR"
"ERR": A code showing what error has occurred
33
PIP On/Off control
•Function
The PIP mode of a product can be turned on or off using a PC.
―Only available on models that have the PIP function.
―The mode cannot be controlled if Video Wall is set to On.
―This function is not available in MagicInfo.
•Viewing PIP on/off state (Get the PIP ON / OFF Status)
Header Command ID Data length Checksum
0xAA 0x3C 0
•Setting PIP on/off (Set the PIP ON / OFF)
Header Command ID Data length Data Checksum
0xAA 0x3C 1 "PIP"
"PIP": A code used to turn the PIP mode of a product on or off
1: PIP ON
0: PIP OFF
•Ack
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x3C "PIP"
"PIP": A code used to turn the PIP mode of a product on or off
•Nak
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x3C "PIP"
"ERR": A code showing what error has occurred
Auto adjustment control (PC and BNC only)
•Function
Automatically adjust the PC system screen using a PC.
•Viewing auto adjustment state (Get Auto Adjustment Status)
None
•Setting auto adjustment (Set Auto Adjustment)
Header Command ID Data length Data Checksum
0xAA 0x3D 1 "Auto
Adjustment"
"Auto Adjustment" : 0x00 (at all times)
•Ack
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x3D "Auto
Adjustment"
•Nak
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x3D "ERR"
"ERR": A code showing what error has occurred
34
Video Wall Mode Control
•Function
Video Wall mode can be activated on a product using a PC.
This control is only available on a product whose Video Wall is enabled.
•Viewing video wall mode (Get Video Wall Mode)
Header Command ID Data length Checksum
0xAA 0x5C 0
•Setting the video wall (Set Video Wall Mode)
Header Command ID Data length Data Checksum
0xAA 0x5C 1 "Video Wall Mode"
"Video Wall Mode": A code used to activate Video Wall mode on a product
1: Full
0: Natural
•Ack
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x5C "Video Wall
Mode"
"Video Wall Mode": A code used to activate Video Wall mode on a product
•Nak
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x5C "ERR"
"ERR": A code showing what error has occurred
Safety Lock
•Function
PC can be used to turn the Safety Lock function on or off on a product.
This control is available regardless of whether or not the power is turned on.
•Viewing the safety lock state (Get Safety Lock Status)
Header Command ID Data length Checksum
0xAA 0x5D 0
•Enabling or disabling safety lock (Set Safety Lock Enable / Disable)
Header Command ID Data length Data Checksum
0xAA 0x5D 1 "Safety Lock"
"Safety Lock": Safety lock code to be set on a product
1: ON
0: OFF
•Ack
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x5D "Safety Lock"
"Safety Lock": Safety lock code to be set on a product
•Nak
Header Command ID Data
length
Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x5D "ERR"
"ERR": A code showing what error has occurred
35
Video Wall On
•Function
Turn Video Wall on or off on the product from your computer.
•Get Video Wall On/Off Status
Header Command ID Data length Checksum
0xAA 0x84 0
•Set Video Wall On/Off
Header Command ID Data length Data Checksum
0xAA 0x84 1 V.Wall_On
•V.Wall_On: Video Wall code to be assigned to the product
1: Video Wall ON
0: Video Wall OFF
•Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'A' 0x84 V.Wall_
On
V.Wall_On : Same as above
•Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x84 ERR
"ERR": A code showing what error has occurred
Video Wall User Control
•Function
Turn the Video Wall function on or off on the product from your computer.
•Get Video Wall Status
Header Command ID Data length Checksum
0xAA 0x89 0
•Set Video Wall
Header Command ID Data length Val1 Val2 Checksum
0xAA 0x89 2 Wall_Div Wall_SNo
Wall_Div: Video Wall Divider code assigned to the product
36
10x10 Video Wall Model
12345678910 11 12 13 14 15
O
0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
1
0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F
2
0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F
3
0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F
4
0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F
5
0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F
6
0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F
7
0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E N/A
8
0x81 0x82 0x83 0x84 0x85 0x86 0x87 0x88 0x89 0x8A 0x8B 0x8C N/A N/A N/A
9
0x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B N/A N/A N/A N/A
10
0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA N/A N/A N/A N/A N/A
11
0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 N/A N/A N/A N/A N/A N/A
12
0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 N/A N/A N/A N/A N/A N/A N/A
13
0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 N/A N/A N/A N/A N/A N/A N/A N/A
14
0xE1 0xE2 0xE3 0xE4 0xE5 0xE6 0xE7 N/A N/A N/A N/A N/A N/A N/A N/A
15
0xF1 0xF2 0xF3 0xF4 0xF5 0xF6 N/A N/A N/A N/A N/A N/A N/A N/A N/A
37
Wall_SNo: Product Number code assigned to the product
10x10 Video Wall Model : ( 1 ~ 100)
Set Number
Data
1 0x01
2 0x02
... ...
99 0x63
100 0x64
•Ack
Header Command ID Data length Ack/Nak r-CMD Val1 Val2 Checksum
0xAA 0xFF 4 'A' 0x89 Wall_Div Wall_SNo
•Nak
Header Command ID Data length Ack/Nak r-CMD Val1 Checksum
0xAA 0xFF 3 'N' 0x89 ERR
"ERR": A code showing what error has occurred
38
Connecting and Using a Source Device
Chapter 03
Before Connecting
Check the following before you connect this product with other devices. Devices that can be connected
to this product include PCs, camcorders, speakers, set top boxes and DVD/Blu-ray Disc players.
Pre-connection Checkpoints
―Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
―Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
―Connect the sound ports correctly: left = white and right = red.
―Check the types of ports at the back of the product you want to connect.
Connecting to a PC
•Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
•A PC can be connected to the product in a variety of ways.
Select a connection method suitable for your PC.
―Connecting parts may differ in different products.
Connection using the D-SUB cable (Analogue type)
RGB IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
39
Connection using a DVI cable (Digital type)
DVI IN /
MAGICINFO IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
―You can use the DVI port on the product as an HDMI port by using a DVI-HDMI adapter.
DVI IN /
MAGICINFO IN
HDMI
Connection Using an HDMI-DVI Cable
―When you connect a PC to the product using an HDMI-DVI cable, set Edit Name to DVI PC to access
video and audio content stored on the PC.
HDMI IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
40
Connection Using an HDMI Cable
HDMI IN
41
Connecting to a Video Device
•Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
•You can connect a video device to the product using a cable.
―Connecting parts may differ in different products.
―Press the SOURCE button on the remote control to change the source.
Connection Using the AV Cable
AV IN / COMPONENT IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
Connection Using the component Cable
AV IN / COMPONENT IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
42
Connection Using an HDMI-DVI Cable
―Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To resolve this, additionally connect an audio cable to the audio ports on the product and video device. When you
connect a video device to the product using an HDMI-DVI cable, set Edit Name to DVI Devices to access video and audio content stored on the video device.
―Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
HDMI IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
HDMI
DVI IN /
MAGICINFO IN
43
Connection Using an HDMI Cable
Using an HDMI cable or HDMI to DVI Cable (up to 1080p)
•For better picture and audio quality, connect to a digital device using an HDMI cable.
•An HDMI cable supports digital video and audio signals, and does not require an audio cable.
- To connect the product to a digital device that does not support HDMI output, use an HDMI-
DVI and audio cables.
•The picture may not display normally (if at all) or the audio may not work if an external device that
uses an older version of HDMI mode is connected to the product. If such a problem occurs, ask
the manufacturer of the external device about the HDMI version and, if out of date, request an
upgrade.
•Be sure to use an HDMI cable with a thickness of 14 mm or less.
•Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a connection
error may occur.
•A basic high-speed HDMI cable or one with ethernet is recommended.
This product does not support the ethernet function via HDMI.
HDMI IN
Connecting to an Audio System
―Connecting parts may differ in different products.
AUDIO OUT
44
Connecting the LAN Cable
―DCE, DCE-M, DCE-H models are only supported.
―Connecting parts may differ in different products.
RJ45
•Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair
45
Connecting the HDBase-T
―EME models are only supported.
―Connecting parts may differ in different products.
―HDBase-T (Tx) transmits data from an external device to HDBase-T (Rx). Make sure to connect them directly using a LAN cable.
―Data transmission is not available if HDBase-T (Rx) is connected to HDBase-T (Tx) through a hub.
―HDBase-T works with unshielded twisted pair (UTP) or shielded twisted pair (STP) cables; but, to ensure CE compliance, STP cables and STP Connectors are required.
Shielded cable and connectors are recommended to safeguard against unpredictable environmental electrical noise which may impact performance.
It is recommended to use an STP cable to maximize performance. Using a UTP cable or patch may decrease performance.
HDBase-T (Tx)HDBase-T (Rx)
HDBT IN
LAN HDMI IN
HDMI OUT
HDMI OUT
HDMI OUT
LAN Cable
46
Changing the Input source
Source
MENU m → Applications → Source List → ENTER E
Source
HDMI HDMI-CEC
DVD Player
AV PCComponent DVI
-The displayed image may differ depending on the model.
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from source list to display the screen
of the selected source.
―The input source can also be changed by using the SOURCE button on the remote control.
―The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.
47
Using MDC
MDC Programme Installation/Uninstallation
Installation
―MDC installation can be affected by the graphics card, mother board and network conditions.
1
Click the MDC Unified installation programme.
2
Select a language for installation. Next, click "OK".
3
When the "Welcome to the InstallShield Wizard for MDC_Unified" screen appears, click "Next".
4
In the "License Agreement" window displayed, select "I accept the terms in the license
agreement" and click "Next".
5
In the displayed "Customer Information" window, fill out all the information fields and click
"Next".
6
In the displayed "Destination Folder" window, select the directory path you want to install the
programme in and click "Next".
―If the directory path is not specified, the programme will be installed in the default directory
path.
7
In the displayed "Ready to Install the Program" window, check the directory path to install the
programme in and click "Install".
8
Installation progress will be displayed.
9
Click "Finish" in the displayed "InstallShield Wizard Complete" window.
―Select "Launch MDC Unified" and click "Finish" to run the MDC programme immediately.
10
The MDC Unified shortcut icon will be created on the desktop after installation.
―The MDC execution icon may not be displayed depending on the PC system or product
specifications.
―Press F5 if the execution icon is not displayed.
Uninstallation
1
Select Settings > Control Panel on the Start menu and double-click Add/Delete Program.
2
Select MDC Unified from the list and click Change/Remove.
Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC.
- For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme is available on the website.
Chapter 04
48
Connecting to MDC
Using MDC via RS-232C (serial data communications standards)
An RS-232C serial cable must be connected to the serial ports on the PC and monitor.
―EDE, EME models are only supported.
RS232C IN RS232C OUT
Monitor 1
Monitor 2
Computer
49
Using MDC via Ethernet
Enter the IP for the primary display device and connect the device to the PC. Display devices can be connected to each other using a LAN cable.
Connection using a direct LAN cable
―Multiple products can be connected using the RJ45 port on the product and the LAN ports on the HUB.
―DCE, DCE-M, DCE-H models are only supported.
RJ45
HUB
Monitor 1
Monitor 2
Computer
50
Screen Adjustment
Configure the Picture settings (Backlight, Colour Tone, etc.).
The layout of the Picture menu options may vary depending on the product.
Chapter 05
Picture Mode
MENU m → Picture → Picture Mode → ENTER E
100
100
45
50
50
50 50
·
·
·
·
·
·
Picture
Backlight
Contrast
Brightness
Sharpness
Colour
Tint (G/R)
100
100
45
50
50
50
Picture Mode Information
G50 R
-The displayed image may differ depending on the model.
-Calibration is only available on the DCE-M, DCE-H models.
Select a picture mode (Picture Mode) suitable for the environment where the product will be used.
Different Picture Mode options are displayed depending on the current input source.
If the input source is PC, DVI, HDMI(PC)
•Information: This mode reduces eye fatigue and is suitable for displaying information to the public.
•Advertisement: This mode is suitable for displaying video content and indoor/outdoor advertisements.
•Calibration: In this mode, the brightness, colour, gamma and uniformity settings customized using the colour calibration
program Advanced Color Management are applied.
-To apply the Calibration mode properly, make sure you configure the picture quality settings, such as brightness,
colour, gamma and uniformity, using the colour calibration programme Advanced Color Management.
-To download the Advanced Color Management programme, visit www.samsung.com/displaysolutions.
If the input source is AV, Component, HDMI(AV)
•Dynamic: This mode is suitable when the ambient light is bright.
•Standard: This mode is generally suitable for any environment.
•Movie: This mode reduces eye fatigue.
•Calibration: In this mode, the brightness, colour, gamma and uniformity settings customized using the colour calibration
program Advanced Color Management are applied.
-To apply the Calibration mode properly, make sure you configure the picture quality settings, such as brightness,
colour, gamma and uniformity, using the colour calibration programme Advanced Color Management.
-To download the Advanced Color Management programme, visit www.samsung.com/displaysolutions.
51
Backlight / Contrast / Brightness /
Sharpness / Colour / Tint (G/R)
MENU m → Picture → ENTER E
100
100
45
50
50
50 50
·
·
·
·
·
·
Picture
Backlight
Contrast
Brightness
Sharpness
Colour
Tint (G/R)
100
100
45
50
50
50
Picture Mode Information
G50 R
-The displayed image may differ depending on the model.
Your product has several options for adjusting picture quality.
Input source Picture Mode Adjustable options
PC, DVI, HDMI, HDBT (when a PC is
connected)
Information / Advertisement Backlight / Contrast / Brightness /
Sharpness
Calibration Backlight
AV, Component, HDMI, HDBT (720p,
1080i, 1080p)
Dynamic / Standard / Movie Backlight / Contrast / Brightness /
Sharpness / Colour / Tint (G/R)
Calibration Backlight
―When you make changes to Backlight, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted
accordingly.
―You can adjust and store settings for each external device you have connected to an input on the product.
―Lowering picture brightness reduces power consumption.
Gamma
MENU m → Picture → Gamma → ENTER E
Gamma 0
-The displayed image may differ depending on the model.
Adjust the primary colour intensity.
―If Picture Mode is set to Calibration, Gamma is disabled.
52
Calibrated value
MENU m → Picture → Calibrated value → ENTER E
Picture
Calibrated value Don't apply
-The displayed image may differ depending on the model.
Select whether to apply the brightness, colour, gamma and uniformity settings customized using the colour calibration
programme Advanced Color Management to the Information and Advertisement modes.
•Don't apply / Apply
―To download the Advanced Color Management programme, visit www.samsung.com/displaysolutions.
―If Picture Mode is set to Calibration, Calibrated value is disabled.
―DCE-M, DCE-H models are only supported.
53
Picture Size
If you have a cable box or satellite receiver, it may have its own set of screen sizes as well. However, we highly recommend you
use your product’s 16:9 mode most of the time.
―Different screen adjustment options are displayed depending on the current input source.
•16:9: Sets the picture to 16:9 wide mode.
•Zoom1: Use for moderate magnification. Cuts off the top and sides.
•Zoom2: Use for a stronger magnification.
•Smart View 1: Reduces the 16:9 picture by 50%.
―Smart View 1 is enabled only in HDMI mode.
•Smart View 2: Reduces the 16:9 picture by 25%.
―Smart View 2 is enabled only in HDMI mode.
•4:3: Sets the picture to basic (4:3) mode.
―Do not set your product to 4:3 format for a long time.
The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn)
which is not covered by the warranty.
•Screen Fit: Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p)
signals are inputted.
•Custom: Changes the resolution to suit the user's preferences.
•Original ratio: If the input source is PC, DVI, HDMI (PC connection) the video will display in the original aspect ratio.
―Available ports may differ depending on the model.
―You can adjust and store settings for each external device you have connected to an input on the product.
Picture Size
MENU m → Picture → Picture Size → ENTER E
·
Picture Size
Position
Resolution Select
Picture Size
O
16:9
-The displayed image may differ depending on the model.
54
Position
·
Picture Size
Position
Resolution Select
Picture Size
O
Zoom1
-The displayed image may differ depending on the model.
Adjusts the picture position. Position is only available if Picture Size is set to Zoom1, Zoom2, Screen Fit.
―To use the Position function after selecting Zoom1, Zoom2 or Screen Fit follow these steps.
1
Press the d button to select Position. Press the E button.
2
Press the u or d button to move the picture up or down.
3
Press the E button.
Zoom/Position
·
Picture Size
Zoom/Position
Resolution Select
Picture Size
O
Custom
-The displayed image may differ depending on the model.
―To use the Zoom/Position function after selecting Custom in HDMI (1080i/1080p) or Component (1080i/1080p) or
Custom, follow these steps.
1
Press the d button to select Zoom/Position. Press the E button.
2
Select the Zoom or Position. Press the E button.
3
Press the u/d/l/r button to move the picture.
4
Press the E button.
―If you want to reset the picture to its original position, select Reset in the Zoom/Position screen.
The picture will be set to its default position.
55
Resolution Select
·
Picture Size
Position
Resolution Select
Picture Size
O
16:9
-Available in PC mode only.
-The displayed image may differ depending on the model.
If the picture is not normal even when the resolution of the graphics card is one of the following, you can optimize the picture
quality by selecting the same resolution for the product as the PC using this menu.
Available resolutions: Off / 1024x768 / 1280x768 / 1360x768 / 1366x768
Auto Adjustment
MENU m → Picture → Auto Adjustment → ENTER E
Picture
Auto Adjustment
-Available in PC mode only.
-The displayed image may differ depending on the model.
Adjust frequency values/positions and fine tune the settings automatically.
56
PC Screen Adjustment
MENU m → Picture → PC Screen Adjustment → ENTER E
PC Screen Adjustment
Fine
Position
Image Reset
Coarse
0
50
-Available in PC mode only.
-The displayed image may differ depending on the model.
•Coarse / Fine
Removes or reduces picture noise.
If the noise is not removed by Fine-tuning alone, use the Coarse function to adjust the frequency as best as possible
(Coarse) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned with the centre
of screen.
•Position
To adjust the PC’s screen position if it is not centred or does not fit the product screen.
Press the u or d button to adjust the Vertical Position. Press the l or r button to adjust the Horizontal Position.
•Image Reset
Resets the image to the default settings.
57
PIP
MENU m → Picture → PIP → ENTER E
Picture
PIP
-The displayed image may differ depending on the model.
-For PIP sound, refer to the Sound Select instructions.
-If you turn the product off while watching in the PIP mode, the PIP function is reset to off.
When you turn your product on, you must turn PIP on again to watch in the PIP mode.
-You may notice that the picture in the PIP screen becomes slightly unnatural when you use
the main screen to view a game or karaoke.
PIP Settings
The picture from the external video source will be in the main screen and the picture from the product will be in the PIP sub-
picture screen.
Main picture Sub picture
AV PC, DVI, HDMI, MagicInfo, HDBT
Component DVI, HDMI, MagicInfo, HDBT
PC AV, HDMI, MagicInfo, HDBT
DVI, HDMI AV, Component, PC
HDBT PC, AV, Component
―Available input sources may vary depending on the model.
•PIP (Off / On): Activate or deactivate the PIP function.
•Source: You can select a source of the sub picture.
•Size ( , , , , , ): Select a size for the subpicture.
•Position ( , , , ): Select a position for the sub-picture.
―In ( , , ) mode, you cannot select Position.
•Sound Select (Main / Sub): You can choose to listen to the sound from the Main picture or the Sub picture.
58
Advanced Settings
MENU m → Picture → Advanced Settings → ENTER E
Advanced Settings
Black Tone
Flesh Tone
RGB Only Mode
Colour Space
White Balance
Motion Lighting
Dynamic Contrast
O
0
O
Native
O
Medium
-The displayed image may differ depending on the model.
Input Source Picture Mode Advanced Settings
PC, DVI, HDMI, MagicInfo,
HDBT (when a PC is connected)
Information White Balance
Advertisement White Balance
AV, Component, DVI, HDMI,
HDBT
Dynamic Not available
AV, Component, DVI, HDMI,
HDBT
Standard Dynamic Contrast / Black Tone / Flesh Tone /
RGB Only Mode / Colour Space / White Balance /
Motion Lighting
Movie Dynamic Contrast / Black Tone / Flesh Tone /
RGB Only Mode / Colour Space / White Balance
―Available input sources may vary depending on the model.
―If Picture Mode is set to Calibration, Advanced Settings is disabled.
59
Advanced Settings
Black Tone
Flesh Tone
RGB Only Mode
Colour Space
White Balance
Motion Lighting
Dynamic Contrast
O
0
O
Native
O
Medium
-The displayed image may differ depending on the model.
Dynamic Contrast
Adjust the screen contrast.
•Off / Low / Medium / High
Black Tone
Select the black level to adjust the screen depth.
•Off / Dark / Darker / Darkest
Flesh Tone
Emphasize pink Flesh Tone.
RGB Only Mode
Displays the Red, Green and Blue colour for making fine adjustments to the hue and saturation.
•Off / Red / Green / Blue
Colour Space
Adjusts the range and variety of colours (the colour space) available to create images.
•Auto / Native
White Balance
Adjust the colour temperature for a more natural picture.
•R-Offset / G-Offset / B-Offset: Adjust each colour’s (red, green, blue) darkness.
•R-Gain / G-Gain / B-Gain: Adjust each colour’s (red, green, blue) brightness.
•Reset: Resets the White Balance to its default settings.
Motion Lighting
Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
•Off / On
60
Picture Options
MENU m → Picture → Picture Options → ENTER E
Picture Options
Colour Temp.
Digital Clean View
MPEG Noise Filter
HDMI Black Level
Film Mode
Motion Plus
Colour Tone
10000K
O
O
Normal
O
O
Standard
-The displayed image may differ depending on the model.
-Motion Plus is only available on the EDE, EME models.
Select an option using the u and d arrow keys, and the press E.
Use the arrow keys to change the setting, and then press E.
Input source Picture Mode Picture Options
PC Information Colour Tone / Colour Temp. / Dynamic Backlight
Advertisement Colour Tone / Colour Temp. / Dynamic Backlight
Calibration Dynamic Backlight
DVI, HDMI, MagicInfo, HDBT
(when a PC is connected)
Information Colour Tone / Colour Temp. / HDMI Black Level /
Dynamic Backlight
Advertisement Colour Tone / Colour Temp. / HDMI Black Level /
Dynamic Backlight
Calibration HDMI Black Level / Dynamic Backlight
AV, Component, DVI, HDMI,
HDBT
Dynamic / Standard / Movie Colour Tone / Colour Temp. / Digital Clean View /
MPEG Noise Filter / Film Mode / Motion Plus /
Dynamic Backlight
Calibration Digital Clean View / MPEG Noise Filter /
HDMI Black Level / Film Mode / Dynamic Backlight
―Available input sources may vary depending on the model.
61
Picture Options
Colour Temp.
Digital Clean View
MPEG Noise Filter
HDMI Black Level
Film Mode
Motion Plus
Colour Tone
10000K
O
O
Normal
O
O
Standard
-The displayed image may differ depending on the model.
-Motion Plus is only available on the EDE, EME models.
Colour Tone
If the input source is PC, DVI, HDMI, MagicInfo, HDBT (PC connection).
•Off / Cool / Standard / Warm
If the input source is AV, Component, DVI, HDMI, HDBT.
•Off / Cool / Standard / Warm1 / Warm2
―Warm1 or Warm2 will be deactivated when the Picture Mode is Dynamic.
―Settings can be adjusted and stored for each external device connected to an input on the product.
―Available input sources may vary depending on the model.
Colour Temp.
Adjust the colour temperature (Red / Green / Blue). (Range: 3000K–15000K)
―This option is available when Colour Tone is set to Off.
Digital Clean View
If the broadcast signal received by your product is weak, you can activate the Digital Clean View feature to reduce any static
and ghosting that may appear on the screen.
•Off / Low / Medium / High / Auto
―When the signal is weak, try all the options until the the product displays the best picture.
MPEG Noise Filter
Reduces MPEG noise to provide improved picture quality.
•Off / Low / Medium / High / Auto
62
HDMI Black Level
Selects the black level on the screen to adjust the screen depth.
•Normal / Low
―This function is only available when the input signal, connected to the product via an HDMI or DVI
connector, is set to RGB444.
Film Mode
This mode is suitable to view movies.
Sets the product to automatically sense and process film signals from all sources and adjust the picture
for optimum quality.
•Off / Auto1 / Auto2
―Available in AV, Component (480i / 1080i), HDMI (1080i).
Motion Plus
―EDE, EME models are only supported.
Removes blur and judder from scenes with larger amounts of rapid movement to provide a clearer
picture.
The menu names may vary depending on the country.
Off : Switches Motion Plus off.
Clear : Sets Motion Plus to Clear (suitable for viewing moving images clearly) mode.
Standard : Sets Motion Plus to Standard mode.
Smooth : Sets Motion Plus to Smooth (suitable for viewing moving images naturally) mode.
Custom : Use to reduce the afterimage and judder as much as you want.
•Blur Reduction : Use to reduce the afterimage as much as you want.
-This is only supported if the Motion Plus is set to Custom.
•Judder Reduction : Use to reduce the judder as much as you want.
-This is only supported if the Motion Plus is set to Custom.
•LED Clear Motion : Make moving images look more clear.
-This is only supported if the Motion Plus is set to Custom.
•Reset: Restore Motion Plus settings to default values.
-The colour on screen may vary with this option unintentionally.
-Disabled when PIP is set to On.
―This function may differ depending on the model.
Dynamic Backlight
Automatically adjust the backlight to provide the best possible screen contrast under the current
conditions.
•Off / On
―The Dynamic Backlight is not available when the input source is set to PC while Video Wall is On.
63
Picture O
MENU m → Picture → Picture Off → ENTER E
Picture
Picture O
Reset Picture
-The displayed image may differ depending on the model.
The product screen is turned off but the audio will continue. Press any key on your remote to turn the screen back on.
Reset Picture
MENU m → Picture → Reset Picture → ENTER E
Reset Picture
Picture
Picture O
-The displayed image may differ depending on the model.
Resets your current picture mode to its default settings.
64
Sound Adjustment
Configure the sound (Sound) settings for the product.
Chapter 06
Sound Mode
MENU m → Sound → Sound Mode → ENTER E
Sound
Sound Eect
Speaker Settings
Reset Sound
Sound Mode Standard
-The displayed image may differ depending on the model.
You can select a sound mode to suit your personal preferences.
•Standard: Selects the normal sound mode.
•Music: Emphasizes music over voices.
•Movie: Provides the best sound for movies.
•Clear Voice: Emphasizes voices over other sounds.
•Amplify: Increase the intensity of high-frequency sound to allow a better listening experience for the hearing impaired.
―If Speaker Select is set to External, Sound Mode is disabled.
65
Sound Eect
MENU m → Sound → Sound Effect → ENTER E
Sound
Sound Eect
Speaker Settings
Reset Sound
Sound Mode Standard
-The displayed image may differ depending on the model.
Configure your preferred sound effect for output sound.
―If Speaker Select is set to External, Sound Effect is disabled.
―Available only when Sound Mode is set to Standard.
•DTS TruSurround HD (Off / On)
This function provides a virtual 5.1 channel surround sound experience through a pair of speakers using HRTF(Head
Related Transfer Function) technology.
•DTS TruDialog (Off / On)
This function allows you to increase the intensity of a voice over background music or sound effects so that dialog can be
heard more clearly.
•Equaliser
Use Equaliser to customize sound setting for each speaker.
-Balance L/R: Adjusts the balance between the right and left speaker.
-100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): Adjusts the level of specific bandwidth frequencies.
-Reset: Resets the equalizer to its default settings.
66
Speaker Settings
MENU m → Sound → Speaker Settings → ENTER E
Sound
Sound Eect
Speaker Settings
Reset Sound
Sound Mode Standard
-The displayed image may differ depending on the model.
•Speaker Select (External / Internal / Receiver)
If you are listening to the sound track of a broadcast or movie through an external receiver, you may hear a sound echo
caused by the difference in decoding speed between the products speakers and the speakers attached to your audio
receiver. If this occurs, set the product to External.
―When you set Speaker Select to External, the products speakers are turned off.
You will hear sound through the external speakers only. When the Speaker Select is set to Internal, both the product
speakers and the external speakers are on. You will hear sound through both.
―If there is no video signal, both the products speakers and the external speakers will be mute.
•Auto Volume (Off / Normal / Night)
The volume can vary depending on the channel.
Automatically equalize the volume level when switching to another channel.
Normal equalizes the volume level on each channel, so that when you change channels, the volume level is the same.
Night equalizes and decrease the volume level on each channel, so each channel is quieter. Night is useful at night,
when you may want to keep the volume low.
―To use the volume control of a connected source device, set Auto Volume to Off. A change to the volume control of
the connected source device may not be applied if Auto Volume is set to Normal or Night.
―If Speaker Settings is set to External, Auto Volume is disabled.
Reset Sound
MENU m → Sound → Reset Sound → ENTER E
Sound
Sound Eect
Speaker Settings
Reset Sound
Sound Mode Standard
-The displayed image may differ depending on the model.
Reset all sound settings to the factory defaults.
67
Network
Chapter 07
Network Status
MENU m → Network → Network Status → ENTER E
You can check the current network and Internet status.
Network Settings
MENU m → Network → Network Settings → ENTER E
Configure network settings to use various smart hub features such as Internet search, content sharing
through a home network and feature updates.
Network type
•Wireless / Wired
Network is only available on the DCE, DCE-M, DCE-H models.
68
Network Settings (Wired)
Connecting to a Wired Network
There are three ways to attach your product to your LAN using cable.
•You can attach your product to your LAN by connecting the LAN port on the back of your product
to an external modem using a LAN cable.
See the diagram below.
RJ45
The Modem Port on the Wall External Modem
(ADSL / VDSL)
Modem Cable LAN Cable
LAN
•You can attach your product to your LAN by connecting the LAN port on the back of your product
to an IP Sharer which is connected to an external modem. Use LAN cable for the connection. See
the diagram below.
The Modem Port on the Wall External Modem
(ADSL / VDSL) IP Sharer
(having DHCP server)
LAN
Modem Cable LAN Cable LAN Cable
RJ45
•Depending on how your network is configured, you may be able to attach your product to your
LAN by connecting the LAN port on the back of your product directly to a network wall outlet using
a LAN cable.
See the diagram below. Note that the wall outlet is attached to a modem or router elsewhere in
your house.
The LAN Port on the Wall
LAN
LAN Cable
RJ45
If you have a Dynamic Network, you should use an ADSL modem or router that supports the Dynamic
Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the IP
address, subnet mask, gateway, and DNS values your product needs to access the Internet so you do not
have to enter them manually. Most home networks are Dynamic Networks.
Some networks require a Static IP address. If your network requires a Static IP address, you must enter the
IP address, subnet mask, gateway, and DNS values manually on your product Cable Setup Screen when
you set up the network connection. To get the IP address, subnet mask, gateway, and DNS values, contact
your Internet Service Provider (ISP).
If you have a Windows computer, you can also get these values through your computer.
―You can use ADSL modems that support DHCP if your network requires a Static IP address.
―ADSL modems that support DHCP also let you use Static IP addresses.
69
Set the network connection to use Internet services such as perform software upgrades.
Automatic Network Settings (Wired)
Connect to the network using a LAN cable.
Make sure a LAN cable is connected first.
How to set up automatically
1
Set Network type to Wired from the Network Settings page.
2
Press the Connect button to start Network Settings.
-The Connect button is only enabled when the LAN cable is properly connected.
3
The network test screen appears and verifies the network connection.
When the connection has been verified, the “Wired network and Internet connection
completed.” message appears.
―If the connection process fails, check the LAN port connection.
―If the automatic process cannot find the network connection values or if you want to set the
connection manually, go to the next section, network setup.
Manual Network Settings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server
address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1
Right click the Network icon on the bottom right of the screen.
2
In the pop-up menu that appears, click Status.
3
On the dialog that appears, click the Support tab.
4
On the Support Tab, click the Details button. The Network connection values are displayed.
How to set up manually
1
Set Network type to Wired from the Network Settings page.
2
Press the Connect button to start Network Settings.
-The Connect button is only enabled when the LAN cable is properly connected.
3
The network test screen appears and the verification process starts. Press Stop. The verification
process stops.
4
Select IP Settings on network connection screen. The IP Settings screen appears.
5
Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry
process for each field in the IP Address.
―Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.
6
When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
7
When the connection has been verified, the “Wired network and Internet connection
completed.” message appears.
70
Network Setting (Wireless)
Connecting to a Wireless Network
The LAN Port on the Wall
Wireless IP sharer
(router having DHCP server)
LAN Cable
USB
Samsung Wireless LAN Adapter
(sold separately)
Samsung recommends using IEEE 802.11n. When you play video over a network connection, the video
may not play smoothly.
―Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the
wireless IP sharer is currently being used by another device nearby, this will result in interference and
communication failure.
―Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is set to
WEP, TKIP or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products will not support a
connection in compliance with new Wi-Fi certification specifications.
―If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC
(Push Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure
the SSID and WPA key in either mode.
―Connection Methods: You can setup the wireless network connection in three ways.
Auto Setup (Using the Auto Network Search function), Manual Setup, WPS(PBC)
Automatic Network Setup (Wireless)
Most wireless networks have an optional security system that requires devices that access the network
to transmit an encrypted security code called an Access or Security Key. The Security Key is based on
a Pass Phrase, typically a word or a series of letters and numbers of a specified length you were asked to
enter when you set up security for your wireless network. If you use this method of setting up the network
connection, and have a Security Key for your wireless network, you will have to enter the Pass Phrase
during the the automatic or manual setup process.
How to set up automatically
1
Set Network type to Wireless from the Network Settings page.
2
The Network function searches for available wireless networks. When done, it displays a list of the
available networks.
3
In the list of networks, press the ▲ or ▼ button to select a network, and then press the E button
twice.
―If the desired wireless router does not appear, select Refresh to search again.
―If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
4
If the Enter password. screen appears, go to step 5. If you select a wireless router that does not
have security, go to step 7.
5
If the router has security, enter the Enter password. (Security key or PIN).
71
6
When done, use the right arrow button to move the cursor to Done, and then press E. The
network connection screen appears and the verification process starts.
―A connection with the router is established, but the Internet cannot be accessed.
7
When the connection has been verified, the “Your wireless network and Internet connection are
setup and ready to use.” message appears.
Manual Network Setup (Wireless)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server
address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1
Right click the Network icon on the bottom right of the screen.
2
In the pop-up menu that appears, click Status.
3
On the dialog that appears, click the Support tab.
4
On the Support Tab, click the Details button. The Network connection values are displayed.
How to set up manually
1
Set Network type to Wireless from the Network Settings page.
2
The Network function searches for available wireless networks. When done, it displays a list of the
available networks.
3
In the list of networks, press the u or d button to select a network, and then press the E button
twice.
―If the desired wireless router does not appear, select Refresh to search again.
―If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
4
If the Enter password. screen appears, go to step 5. If you select a wireless router that does not
have security, go to step 7.
5
If the router has security, enter the Enter password. (Security key or PIN).
6
When done, use the right arrow button to move the cursor to Done, and then press E. The
network connection screen appears and the verification process starts.
7
Select Stop while network connections are being attempted. This will stop the connection.
8
Select IP Settings on network connection screen. The IP Settings screen appears.
9
Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry
process for each field in the IP Address.
―Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.
72
10
When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
11
When the connection has been verified, the “Your wireless network and Internet connection are
setup and ready to use.” message appears.
WPS(PBC)
How to set up using WPS(PBC)
If your router has a WPS(PBC) button, follow these steps.
1
Set Network type to Wireless from the Network Settings page.
2
Select WPS(PBC), press E, and then press E again.
3
Press the WPS(PBC) button on your router within 2 minutes. Your product automatically acquires all
the network setting values it needs and connects to your network.
4
The network connection screen appears, and network setup is done.
73
Wi-Fi Direct
MENU m → Network → Wi-Fi Direct → ENTER E
―To use this function, your mobile device should be supported by the Wi-Fi Direct.
Set to connect the product to wireless mobile devices. Using this function, you can connect wireless
mobile devices with your product directly without a router.
To connect your mobile device with your product using Wi-Fi
Direct, follow these steps:
1
Go to Wi-Fi Direct screen. The product starts to search devices.
2
Turn on the Wi-Fi Direct function on your device. Select the desired Wi-Fi device.
•PBC (Push Button Configuration): Press the WPS(PBC) button on your Wi-Fi device within 2
minutes. Your product automatically acquires all the network setting values it needs and connects
to your network.
•PIN: Input the displayed PIN on your device.
―If you want to disconnect the device, select the connected Wi-Fi device, and then select
Disconnected.
AllShare Settings
MENU m → Network → AllShare Settings → ENTER E
Shows a list of mobile phones or connected devices which have been set up to use the AllShare Play
function with this product.
•Allow / Deny: Allows/Blocks the devices.
•Delete from the list: Deletes the devices from the list.
―This function only deletes the name of the device from the list. If the deleted device is turned on
or tries to connect to the product, it may appear on the list again.
Using the AllShare Play Function
An alarm window appears informing you that media contents (videos, photos, music) sent from a mobile
phone will be displayed on your product. The contents are played automatically 3 seconds after the
alarm window appears. If you press the RETURN or EXIT button when the alarm window appears, the
media contents are not played.
―The first time a device accesses your product through the media function, a warning popup window
appears. Press the E button to select Allow. This permits the phone to access the product freely
and use the AllShare Play function to play content.
―To turn off media contents transmissions from a mobile phone, set Deny in the AllShare Settings.
―Contents may not play on your product depending on their resolution and format.
―The E and ◄ / ► buttons may not work depending on the type of media content.
―Using the mobile device, you can control the AllShare Play. For details, refer to each mobile’s user’s
guide.
74
Server Network Settings
MENU m → Network → Server Network Settings → ENTER E
Connect to server
To run Player connect to a network.
•Server Address / SSL / Port
―If the SSL option is enabled, the server is configured to use https and data transfer is encrypted.
―Enter the server IP address and port number. Use 7001 as the port number. (If unable to connect to
the server using port number 7001, check with your server administrator to find the correct port
number and then change the port number.)
Server Access
Select a method to connect the server network.
•Allow / Deny
FTP Mode
Specify the FTP operating mode.
•Active / Passive
Device Name
MENU m → Network → Device Name → ENTER E
Select or enter a device name.
This name can be shown on network remote controls over the network.
•User Input / [Signage]Display 1 ~ 6
75
Applications
Chapter 08
Source List
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a
source from Source List to display the screen of the selected source.
―The input source can also be changed by using the SOURCE button on the
remote control.
―The screen may not display correctly if an incorrect source is selected for the
source device you want to convert to.
MENU m → Applications → Source List → ENTER E
Applications
Source List
MagicInfo Lite
-The displayed image may differ depending on the model.
Refresh
MENU m → Applications → Source List → TOOLS → Refresh → ENTER E
If you cannot find a device you want, select Refresh to refresh the list.
Edit Name
MENU m → Applications → Source List → TOOLS → Edit Name → ENTER E
Sometimes the screen will not display properly unless the name of a source device is specified in Edit Name.
In addition, it is best to rename the source device in Edit Name to obtain optimal picture quality.
―The list can include the following source devices. Source devices on the list differ depending on the selected source.
VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game / Camcorder / PC / DVI PC / DVI Devices / TV /
IPTV / Blu-ray / HD DVD / DMA
―Available settings in the Picture menu depend on the current source and settings made in Edit Name.
Information
MENU m → Applications → Source List → TOOLS → Information → ENTER E
You can see detailed information about the selected external device.
76
MagicInfo Lite
MENU m → Applications → MagicInfo Lite → ENTER E
Applications
MagicInfo Lite
Source List
-The displayed image may differ depending on the model.
MagicInfo is a business solution that allows the product to be used as a signage (advertising media). Using the solution, play
image and video files from the internal memory or a connected USB storage device.
―DCE, DCE-M, DCE-H models are only supported.
Playing content from the internal memory or USB
Play content from the internal memory or a connected USB storage device.
77
Device : All Content : All Sort by : File Name
Options
-The displayed image may differ depending on the model.
Network Channel
Play content, templates and schedules configured on the server.
•You can view whether the server is connected (approval) in the Player menu
screen.
To view whether the server is connected when a Network Channel is
running, press INFO on the remote.
1
Select Network Channel from the Player menu.
―The No channels message appears if no channel has been registered in
Network Channel.
2
Network Channel will run.
Available features in the MagicInfo page
The MagicInfo list page provides the following features.
•Device
-Select either Internal or USB to search for a desired device list.
All / Internal / USB
•Content
-Select a content type as criterion to search for a desired content list.
All / Video / Image
•Sort by
Specify the content sort criterion.
-File Name / Recently played
•Options
Options menu items in the MagicInfo screen
Option Name Operations
Play Selected
Select and play desired content.
Send
Copy content to another storage device.
Delete
Delete desired content.
Settings
Configure detailed properties of content.
―See the following page for details on the Settings feature.
78
Settings
Settings
Default Storage
Repeat Mode
Picture Size
Display Duration
Safely Remove USB Device
Reset Settings
Internal
One
Select the storage location that you want to download scheduled channels from
the network to.
Close
-The displayed image may differ depending on the model.
Default Storage
Select the storage location that you want to download scheduled channels from the network to.
•Internal / USB
Repeat Mode
Set repeat mode whether to repeat playing contents or not.
•One / All
Picture Size
Set Picture Size to either Fit to Screen or Original Size.
•Fit to Screen / Original Size
―Available only for Video and Image content.
Display Duration
Set the duration for each page in a slideshow.
―Available only for Template and Image content.
Safely Remove USB Device
Safely removes USB memory
Reset Settings
Restore all the values under Settings to the default when the product was purchased.
79
System
Chapter 09
Setup
MENU m → System → Setup → ENTER E
English
O
System
Menu Language
Multi Control
Time
Eco Solution
Auto Protection Time
Screen Burn Protection
Setup
-The displayed image may differ depending on the model.
Go through the initial setup steps like you did the first time you used this product.
―Enter your 4 digit PIN number. The default PIN number is “0-0-0-0".
If you want to change the PIN number, use the Change PIN function.
Set the HDBaseT standby mode.
―EME models are only supported.
•Off: The device cannot be turned on via HDBT once it is turned off.
•On: Keep the HDBT module active when the device is turned off. (This uses more power.)
80
Menu Language
MENU m → System → Menu Language → ENTER E
Set the menu language.
―A change to the language setting will only be applied to the onscreen menu display. It will not be
applied to other functions on your PC.
Multi Control
MENU m → System → Multi Control → ENTER E
Conguring settings for Multi Control
•ID Setup
Assign an ID to a set. (Range: 0~99)
Press u or d to select a number, and press E.
•ID Input
Enter the ID number of the product connected to the input cable for input signal reception.
Enter the number you want using the number buttons on the remote control.
•PC Connection
Select a method to connect to MDC to receive the MDC signal.
―DCE, DCE-M, DCE-H models are only supported.
-RS232C cable
Communicates with the MDC via a RS232C cable.
-RJ-45 (LAN)/Wi-Fi Network
Communicate with MDC over Wi-Fi.
81
Time
MENU m → System → Time → ENTER E
O
Time
Sleep Timer
On Timer
O Timer
Holiday Management
Clock Set
-The displayed image may differ depending on the model.
You can configure Clock Set or Sleep Timer. You can also set the product to automatically turn on or off at a specified time
using the Timer function.
Clock Set
Select Clock Set. Select Date or Time, and then press E.
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to
move from one entry field to the next. Press E when done.
―Available only when Clock Mode is set to Manual.
―You can set the Date and Time directly by pressing the number buttons on the remote control.
Sleep Timer
Automatically shuts off the product after a preset period of time.
(Off / 30 min / 60 min / 90 min / 120 min / 150 min / 180 min)
―Use the up and down arrows to select a period of time, and then press E. To cancel Sleep Timer, select Off.
On Timer
Set On Timer so that your product turns on automatically at a time and on a day of your choosing.
The power is turned on with the specified volume or input source.
On Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the current time first.
(On Timer 1 ~ On Timer 7)
―You must set the clock before you can use On Timer.
•Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose the
days you want On Timer to turn on your product.
―The check mark indicates days you’ve selected.
•Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left
and right arrow buttons to change entry fields.
•Volume: Set the desired volume level. Use the left and right arrow buttons to change the volume level.
•Source: Select the input source of your choice.
82
O Timer
Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer 1 ~ Off Timer 7)
―You must set the clock before you can use Off Timer.
•Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose the
days you want Off Timer to turn off your product.
―The check mark indicates days you’ve selected.
•Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left
and right arrow buttons to change entry fields.
Holiday Management
Timer will be disabled during a period specified as a holiday.
•Add: Specify the period you want to add as a holiday.
Select the start and end dates of the holiday you want to add using the u/d buttons, and click the Save button.
The period will be added to the list of holidays.
-Start: Set the start date of the holiday.
-End: Set the end date of the holiday.
-Delete: Delete all items from the list of holidays.
Select Delete. The message "Delete all holidays?" will appear.
Select Yes. All holidays will be deleted.
•Apply: Set the On Timer and Off Timer to not activate on public holidays.
-Press E to select the On Timer and Off Timer settings you do not want to activate.
-The selected On Timer and Off Timer will not activate.
O
Time
Sleep Timer
On Timer
O Timer
Holiday Management
Clock Set
-The displayed image may differ depending on the model.
83
Eco Solution
MENU m → System → Eco Solution → ENTER E
O
15 min
O
Eco Solution
Eco Sensor
No Signal Power O
Auto Power O
Energy Saving O
-The displayed image may differ depending on the model.
Energy Saving
Reduce the power consumption by adjusting the screen brightness.
•Off / Low / Medium / High
Eco Sensor
To enhance your power savings, the picture settings will automatically adapt to the light in the room.
•Off / On
―Adjusting the Backlight setting under Picture while Eco Sensor is on will disable the Off.
―If the screen contrast is not sufficient, set the Eco Sensor to Off.
If the Eco Sensor is Off, it may not comply with energy standards.
Min. Backlight
When Eco Sensor is On, you can manually adjust the minimum screen brightness. Min. Backlight is the darkest backlight
mode. Make sure the Min. Backlight setting is lower than the Backlight setting.
―If Eco Sensor is On, the display brightness may change (become slightly darker or brighter) depending on the surrounding
light intensity.
No Signal Power O
Save power by turning the device off when no signal is received from any source.
•Off / 15 min / 30 min / 60 min
―Disabled when an attached PC is in power saving mode.
―The product will automatically power off at a specified time. The time can be changed as required.
Auto Power O
The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel
within 4 hours to prevent overheating.
•Off / On
84
Auto Protection Time
MENU m → System → Auto Protection Time → ENTER E
System
Auto Protection Time O
-The displayed image may differ depending on the model.
If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the
formation of burnt in ghost images on the screen.
•Off / 2 hours / 4 hours / 8 hours / 10 hours
85
Screen Burn Protection
MENU m → System → Screen Burn Protection → ENTER E
Screen Burn Protection
Timer
Immediate display
Side Grey
Pixel Shift O
O
O
O
-The displayed image may differ depending on the model.
To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology.
Pixel Shift moves the picture slightly on the screen.
The Pixel Shift Time setting allows you to programme the time between movements of the picture in minutes.
Pixel Shift
Minimize image retention by finely moving pixels horizontally or vertically.
•Pixel Shift (Off / On)
―Horizontal, Vertical and Time are enabled only when Pixel Shift is set to On.
•Horizontal: Sets how many pixels the screen moves horizontally.
•Vertical: Sets how many pixels the screen moves vertically.
•Time: Set the time interval for performing the horizontal or vertical movement, respectively.
Available Pixel Shift Settings and Optimum Settings.
Available Settings Optimum Settings
Horizontal (pixels)
0 ~ 4 4
Vertical (pixels)
0 ~ 4 4
Time (minute)
1 min ~ 4 min 4 min
―The Pixel Shift value may differ depending on the product size (inches) and mode.
―Displaying a still image or a 4:3 output for an extended period of time may cause image retention. This is not a defect in the
product.
―If Picture Size is set to Screen Fit, Pixel Shift is disabled.
86
Screen Burn Protection
Timer
Immediate display
Side Grey
Pixel Shift O
O
O
O
-The displayed image may differ depending on the model.
Timer
You can set the timer for Screen Burn Protection.
The Screen Burn Protection feature stops automatically after a specified period of time.
Timer
•Off
•Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
―Period and Time can be configured when Repeat is selected.
•Interval: Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to
End Time).
―The option is enabled only when Clock Set is configured.
•Mode: Select a screen protective pattern to display.
-Pixel: Pixels on the screen alternate black continuously.
-Rolling bar: A vertical bar moves left to right.
-Fading screen: The entire screen becomes brighter, then darker.
―The Rolling bar and Fading screen patterns appear only once regardless of the specified repeat period or time.
•Period: Specify the time interval to activate the Screen Burn Protection function.
-1 hour ~ 10 hour
―The option is enabled when Repeat is selected for Timer.
•Time: Specify the duration to keep the Screen Burn Protection function on.
-10 Sec ~ 50 Sec
―Enabled when Timer is set to Repeat and Mode is set to Pixel.
•Start Time: Set the start time to activate the screen protection function.
―The option is enabled when Interval is selected for Timer.
•End Time: Set the end time to deactivate the screen protection function.
―The option is enabled when Interval is selected for Timer.
87
Screen Burn Protection
Timer
Immediate display
Side Grey
Pixel Shift O
O
O
O
-The displayed image may differ depending on the model.
Immediate display
Select the screen saver you want to display immediately.
•Off / Pixel / Rolling bar / Fading screen
Side Grey
When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen.
•Off / Light / Dark
88
Ticker
MENU m → System → Ticker → ENTER E
System
Ticker O
-The displayed image may differ depending on the model.
-The Ticker function is only available when Menu Language is set to English.
Input text while a video or image is displayed and display the text on the screen.
•Off / On
―Message, Time, Position, Motion, and Font Style are enabled only when Ticker is set to On.
•Message: Enter a message to display on the screen.
•Time: Set the Start Time and End Time to display a Message.
•Position: Select an orientation to display a Message from Horizontal and Vertical.
-Horizontal (Left / Centre / Right)
-Vertical (Top / Middle / Bottom)
•Motion: Specify the Direction and Speed to display a Message.
-Motion (Off / On)
-Direction (To the Left / To the Right / To the Top / To the Bottom)
-Speed (Slow / Normal / Fast)
―Direction and Speed are enabled only when Motion is set to On.
•Font Style: Specify the message Size and Font colour.
89
Video Wall
MENU m → System → Video Wall → ENTER E
·
·
·
·
Video Wall
Full
1
1
Format
Horizontal
Vertical
Screen Position
Video Wall On
-The displayed image may differ depending on the model.
-Some models may not support the MagicInfo function.
-The Video Wall option is only enabled when PIP is set to O.
-If more than four displays are connected horizontally and vertically, it is recommended that
you use an input resolution of XGA (1024 x 768) level or higher to prevent a dark picture due
to degradation in the contrast or colour intensity.
Customize the layout of multiple displays that are connected to form a video wall.
In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays.
To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support the MagicInfo
function.
Video Wall
You can activate or deactivate Video Wall.
To organize a video wall, select On.
Format
Select a format to display images on multiple displays.
•Full: Display images in full screen.
•Natural: Display images at the original resolution without enlarging or reducing.
―The Format option is only enabled when Video Wall is set to On.
Horizontal
This function automatically divides the screen according to the specified number of horizontal displays.
Enter the number of horizontally arranged displays.
The horizontal screen will automatically be divided according to the number entered.
A maximum of 15 displays can be assigned to the horizontal arrangement.
―The screen can be divided into a maximum of 100 screens (horizontal and vertical screens multiplied). For example, if the
horizontal arrangement is set to 15, a maximum of 6 displays can be assigned to the vertical arrangement. Conversely, if the
vertical arrangement is set to 15, a maximum of 6 displays can be assigned to the horizontal arrangement.
―The Horizontal option is only enabled when Video Wall is set to On.
90
·
·
·
·
Video Wall
Full
1
1
Format
Horizontal
Vertical
Screen Position
Video Wall On
-The displayed image may differ depending on the model.
Vertical
This function automatically divides the screen according to the specified number of vertical displays.
Enter the number of vertically arranged displays.
The vertical screen will automatically be divided according to the number entered.
A maximum of 15 displays can be assigned to the vertical arrangement.
―The screen can be divided into a maximum of 100 screens (horizontal and vertical screens multiplied). For example, if the
horizontal arrangement is set to 15, a maximum of 6 displays can be assigned to the vertical arrangement. Conversely, if the
vertical arrangement is set to 15, a maximum of 6 displays can be assigned to the horizontal arrangement.
―The Vertical option is only enabled when Video Wall is set to On.
Screen Position
You can customize the arrangement of split screens by moving displays identified with a number using the Screen Position
function.
Select Screen Position to display the arrangement of displays (identified with a number) specified according to the
Horizontal or Vertical settings. To customize the arrangement, move a number (display) using the direction buttons on the
remote control and press E.
―A maximum of 100 displays can be arranged in Screen Position.
―The Screen Position option is only enabled when Video Wall is set to On.
―The Screen Position window is only displayed when Horizontal and Vertical are configured.
91
Source AutoSwitch Settings
MENU m → System → Source AutoSwitch Settings → ENTER E
·
·
·
Source AutoSwitch Settings
O
All
PC
Primary Source Recovery
Primary Source
Secondary Source
Source AutoSwitch On
-The displayed image may differ depending on the model.
Turning on the display with Source AutoSwitch On, and the previous video source selection is not active, the display will
automatically search the different video input sources for active video.
Source AutoSwitch
When the Source AutoSwitch is On, the display video source will automatically be searched for active video.
The Primary Source selection will be activated, if the current video source is not recognized.
Secondary Source selection will become active, if no primary video source is available.
If both the primary and secondary input sources are not recognized, the display will perform two searches for an active source,
each search checking the primary and then secondary source. If both searches fail, the display will return to the first video
source and display a message indicating that there is no signal.
When the Primary Source selection is set to All, the display will search all the video source inputs twice in sequence looking
for an active video source, returning back to the first video source in the sequence if no video is found.
Primary Source Recovery
Select whether to restore the selected primary input source when a primary input source is connected.
―The Primary Source Recovery function is disabled if Primary Source is set to All.
Primary Source
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
92
Change PIN
MENU m → System → Change PIN → ENTER E
System
Change PIN
-The displayed image may differ depending on the model.
The Change PIN screen will appear.
Choose any 4 digits for your PIN and enter it in Enter New PIN. Reenter the same 4 digits in Confirm New PIN.
When the Confirm screen disappears, press the Close button. The product has memorised your new PIN.
93
General
MENU m → System → General → ENTER E
O
O
O
O
O
O
General
Game Mode
Auto Power On
Safety Lock
Button Lock
Standby Control
Network Standby
Max. Power Saving On
-The displayed image may differ depending on the model.
Max. Power Saving
Turns off the product to reduce power consumption after the PC has been left idle for a specified period of time.
•Off / On
―Available only PC, DVI, HDMI mode.
Game Mode
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by
selecting game mode.
•Off / On
―Precautions and limitations for Game Mode
To disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.
―Game Mode is not available when the input source is set to PC.
―If Game Mode is On. Picture Mode is set to Standard and Sound Mode is set to Movie.
Auto Power On
This feature automatically turns on the product as soon as it is plugged in. Pressing the power button is not needed.
•Off / On
Safety Lock
It sets safe lock function.
•Off / On
All the menus and buttons of the product and remote control, except for the LOCK button on the remote control, will be
locked by the Safety Lock function.
To unlock the menus and buttons, press the LOCK button and then enter the password (default password: 0 - 0 - 0 - 0).
94
O
O
O
O
O
O
O
General
Game Mode
Auto Power On
Safety Lock
Button Lock
Standby Control
HDBT Standby
Network Standby
Max. Power Saving On
-The displayed image may differ depending on the model.
Button Lock
This menu can be used to lock the buttons on the product.
Only the remote control can control the product if Button Lock is set to On.
•Off / On
Standby Control
You can set the screen standby mode to be applied when an input signal is received.
•Auto
Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.
The message No Signal will appear if no source device is connected.
•On
Power-saving mode will activate if no input signals are detected.
•Off
The message No Signal will appear if no input signals are detected.
―The Standby Control option is only enabled when Source List is set to PC, DVI, HDMI.
―If No Signal is displayed although a source device is connected, check the cable connection.
HDBT Standby
Keep the HDBT module active when the device is turned off. (This uses more power.)
•Off / On
―EME models are only supported.
Network Standby
This feature keeps the network power on when the product turns off.
•Off / On
―This function is only available for models that can connect to a network.
95
General
OSD Display
Power On Adjustment
Temperature Control
0 Sec
77
O
Lamp Schedule
-The displayed image may differ depending on the model.
Lamp Schedule
Adjusts the luminance to a user-specified value at a specified time.
•Off / On
OSD Display
Displays or hides a menu item on the screen.
•Source OSD / No Signal OSD / MDC OSD
Power On Adjustment
You can set the warm-up time for the screen to turn on after the power button is pressed. (Range: 0 – 50 seconds)
―A warm-up time that is too short may damage the product due to overvoltage.
Temperature Control
This function detects the internal temperature of the product. You can specify the temperature range that is acceptable.
The default temperature is set to 77 C.
The recommended operating temperature for this product is 75 to 80 C (based on an ambient temperature of 40 C).
―The screen will become darker if the current temperature exceeds the specified temperature limit. If the temperature
continues to rise, the product will power off to prevent overheating.
96
Anynet+ (HDMI-CEC)
MENU m → System → Anynet+ (HDMI-CEC) → ENTER E
Anynet+ (HDMI-CEC)
Auto Turn O
Anynet+ (HDMI-CEC)
Yes
On
-The displayed image may differ depending on the model.
-The Anynet+ functions do not operate with other manufacturers’ products.
-For instructions explaining how to connect Anynet+ external devices, refer to the device’s user
manual.
-You can connect only one receiver (home theatre).
Anynet+ (HDMI-CEC)
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung
product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your
Samsung device has this feature, check if there is an Anynet+ logo on it.
―You can only control Anynet+ devices using the product remote control, not the buttons on the product.
―The product remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
―Anynet+ works when the AV device supporting Anynet+ is in the standby or on status.
―While in PIP mode, Anynet+ functions only when an AV device is connected as the primary display. It does not work if the
AV device is connected as a secondary display.
―Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the product.
Anynet+ Menu Description
View PC
Changes Anynet+ mode to PC mode.
Device List
Shows the Anynet+ device list.
(device_name) MENU
Shows the menu of the connected device menus. E.g. if a DVD player is connected,
the disc menu of the DVD player will appear.
(device_name) Tools
Shows the tools menu of the connected device. E.g. if a DVD player is connected, the
tools menu of the DVD player will appear.
―Depending on the device, this menu may not be available.
(device_name) Title Menu
Shows the title menu of the disc in the connected device. E.g. If a DVD player is
connected, the title menu of the movie in the DVD player will appear.
―Depending on the device, this menu may not be available.
97
Anynet+ (HDMI-CEC)
Auto Turn O
Anynet+ (HDMI-CEC)
Yes
On
-The displayed image may differ depending on the model.
Auto Turn O
Setting an Anynet+ Device to turn Off automatically when the product is turned off.
•No / Yes
―If Auto Turn Off is set to Yes, running external devices will turn off at the same time as the product powers off.
―May not be enabled depending on the device.
Switching between Anynet+ Devices
1
Press the TOOLS button, select Anynet+ (HDMI-CEC), and then press E.
2
Select Device List, and then press the E button.
If you cannot find a device you want, select Refresh to refresh the list.
3
Select a device, and then press the E button. You can switch to the selected device.
―The Device List menu appears only when you set Anynet+ (HDMI-CEC) to On in the System menu.
―Switching to the selected device may take up to 2 minutes. You cannot cancel the switching operation while switching is in
progress.
―If you have selected an Anynet+ device by pressing the SOURCE button and then selecting its input source, you cannot use
the Anynet+ function.
―Make sure to switch to an Anynet+ device by using the Device List.
98
Troubleshooting for Anynet+
Problem Possible Solution
Anynet+ does not work.
•Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
•You can connect only one receiver (home theatre).
•Check if the Anynet+ device power cord is properly connected.
•Check the Anynet+ device’s Video/Audio/HDMI cable connections.
•Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+setup menu.
•Check whether the remote control is Anynet+ compatible.
•Anynet+ doesn’t work in certain situations. (initial setup)
•If you have removed and then reconnected the HDMI cable, please make sure to search devices again or turn your product
off and on again.
•Check if the Anynet+ function of the Anynet device is set on.
I want to start Anynet+.
•Check if the Anynet+ device is properly connected to the product and check if the Anynet+ (HDMI-CEC) is set to On in the
Anynet+ System menu.
•Press the TOOLS button to display the Anynet+ menu and select a menu you want.
I want to exit Anynet+.
•Select View PC in the Anynet+ menu.
•Press the SOURCE button on the product remote control and select a non- Anynet+ device.
The message “Disconnecting
Anynet+ device ...” appears on the
screen.
•You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
•Use the remote control after the product has completed Anynet+ configuration or has finished switching to Anynet+.
The Anynet+ device does not
play.
•You cannot use the play function when initial setup is in progress.
99
Problem Possible Solution
The connected device is not
displayed.
•Check whether or not the device supports Anynet+ functions.
•Check whether or not the HDMI cable is properly connected.
•Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ System menu.
•Search Anynet+ devices again.
•Anynet+ requires an HDMI connection. Make sure the device is connected to your product with an HDMI cable.
•Some HDMI cables may not support Anynet+ functions.
•If the connection is terminated because there has been a power failure or the HDMI cable has been disconnected, please
repeat the device scan.
100
Reset System
MENU m → System → Reset System → ENTER E
System
Reset System
-The displayed image may differ depending on the model.
This option returns the current settings under system to the default factory settings.
Clone Product
MENU m → System → Clone Product → ENTER E
Clone Product
Clone from USB
Clone to USB
-The displayed image may differ depending on the model.
Export the product settings to a USB device or load the settings via a USB device.
This option is useful when assigning the same settings to several products.
•Clone to USB: Copy the product settings to a USB device.
•Clone from USB: Assign the settings saved in a USB device to the product.
-After configuration is complete, the product is rebooted automatically.
―The option may not work properly if the USB device contains a file other than a settings file.
―Confirm that the USB device functions properly before running the option.
―The option is available for products with the same Model Code and Software Version.
Go to Support → Contact Samsung and find the product Model Code and Software Version.
101
Reset All
MENU m → System → Reset All → ENTER E
This option returns all the current settings for a display to the default factory settings.
DivX® Video On Demand
MENU m → System → DivX® Video On Demand → ENTER E
Shows the registration code authorized for the product.
If you connect to the DivXⓇ web site and register using that code, you can download the VOD
registration file.
For more information about DivXⓇ VOD, visit “http://vod.divx.com”.
PC module power
MENU m → System → PC module power → ENTER E
The PC module can be turned on/off separately from the LFD.
Synced power-on
Set to Off to turn on the PC module without turning on the LFD.
•Off / On
Synced power-o
Set to Off to turn off the PC module without turning off the LFD.
•Off / On
102
Support
Chapter 10
Software Update
MENU m → Support → Software Update → ENTER E
The Software Update menu lets you upgrade your product software to the latest version.
―Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade.
―When you upgrade software, all video and audio settings you have made will return to their default settings. We advise you to write down your settings so that you can
easily reset them after the upgrade.
Update now
Update the software to the latest version.
Contact Samsung
MENU m → Support → Contact Samsung → ENTER E
View this information when your product does not work properly or when you want to upgrade the software.
You can find information regarding our call centres and how to download products and software.
―Contact Samsung and find the product Model Code and Software Version.
103
Play photos, videos or music saved on a storage device.
Play a variety of content using the following methods.
•Using a USB device: Play media content such as videos, photos and music from a USB device.
•Connecting a storage device: Play media content saved on a storage device such as a smartphone, camera, PC or cloud service.
Read the following before using media play with a USB device
Caution
•Before connecting a USB device to the product, back up files to ensure your data is not damaged or lost.
Samsung Electronics is not liable for any damage or loss of data.
•Do not remove a USB device while it is loading.
•If a USB device is connected using a USB extension cable, the USB device may not be recognized or files saved on the device may not be able to be read.
•If the product does not recognize a connected USB device, the files on the USB device may be corrupted or may not be able to be played.
If this occurs, connect the USB device to the PC to format the device, then make sure the device is connected properly.
•USB HDD greater than 2TB is not supported.
Playing photos, videos and music (Media Play)
Chapter 11
Enjoy videos, photos, music files saved on a USB Mass Storage Class (MSC) device.
104
Compatible devices with media play
•Some USB digital cameras, smartphones and audio devices may not be compatible with the product.
•Media play is only compatible with USB MSC devices.
•MSC device refers to a Mass Storage Class Bulk-Only Transport device.
Examples of MSC devices include Thumb drives, Flash card readers and USB HDDs. (USB hubs are not supported.)
These MSC devices must be connected directly to a USB port on the product.
•If more than one Picture Transfer Protocol (PTP) device is connected, only one will work at a time.
•If multiple MSC devices are connected, some devices may not be recognized. USB devices that require high power (higher than 500mA or 5V) may not be supported.
•If an overheating warning message appears when a USB device is connected or used, the USB device may not be recognized or function properly.
•The screensaver activates if the product is left idle for a period of time specified in Auto Protection Time.
•Power-saving mode on some external hard disk drives may automatically deactivate after connecting to the product.
File system and formats
•Media play may not function properly with unlicensed multimedia files.
•Media Transfer Protocol (MTP) is not supported.
•Supported file systems include FAT16, FAT32 and NTFS (read only).
•Media play supports the sequential JPEG format.
It does not support the progressive JPEG format.
•Images with a higher resolution take longer to be displayed on the screen.
•The maximum JPEG resolution supported is 15360x8640 pixels.
•If a file is incompatible or corrupted, a message Not Supported File Format. appears.
•When sorting files in folder view mode, a maximum of 1000 files can be displayed in each folder.
•If a USB device contains 8000 files and folders or more, some files and folders may not open.
•DRM MP3 files downloaded from websites that charge a fee cannot be played.
―Digital Rights Management (DRM) refers to a system for protecting the copyrights of data circulated via the Internet or other digital media by enabling secure
distribution and/or disabling illegal distribution of the data.
105
Using a USB device
Connecting a USB device
1
Turn on your product.
2
Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product.
3
The New device connected. page automatically appears as soon as a USB device connects to the product.
―If only one USB device is connected, files saved on the USB device are displayed automatically.
―To view content saved on a USB device, connect the USB device to a USB port on the product.
Removing a USB device
Removing a USB device from Source
1
Press SOURCE on the remote control. Alternatively, go to Source using the OSD menu.
SOURCE → Source
2
Select USB from Source, and then press the TOOLS button on the remote control. Optional menu items are displayed.
3
Select Disconnect USB Device and wait until the USB device is disconnected. The USB device is disconnected.
It is recommended to use a USB HDD that
has a power adapter.
It is recommended to remove a USB
device using the Disconnect USB Device
function.
106
Menu items in the media content list page
Option Name Operations Photos Videos Music
Slide Show
Start a slideshow.
―This menu item is not available if Sort by is set to Folder.
c
Encoding
Select an encoding language if the title of media content appears corrupted. c
Play Selected
Select and play desired content from the media content list. ccc
107
Available buttons and features during photo playback
Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.
•Previous / Next
View the previous or next photo.
•Start Slide Show / Stop Slide Show
Start or stop a slideshow. Using a slideshow, it is possible to play all photos in a folder.
•Slideshow Settings
-Speed: Change the slideshow speed.
-Effects: Apply transition effects between photos.
•Zoom
Zoom in on photos up to 4x.
•Rotate
Rotate photos.
•Background Music
Play background music while viewing photos.
-Background Music / Mini Player
―Make sure a music file is saved on the same device.
―Pause the current music playing or switch to another music file using Mini Player.
•Settings
Option Name Operations
Picture Mode
Change the Picture Mode.
Sound Mode
Change the Sound Mode.
―This menu item is only available when Background Music is playing.
Information
View information about a file.
Pressing the INFO button while a file is
selected will display information about the
selected file.
108
Available buttons and features
during video playback
Pressing the E or TOOLS button displays the following buttons. The RETURN
button makes the buttons disappear.
•Pause / Play
Pause or play a video.
The following features are available in pause mode. Note that sound cannot
be heard in pause mode.
•Rewind / Fast Forward
Rewind or fast forward a video. Speed up playback up to 3x, if required. To
change the playback speed to the original speed, select ∂.
•Previous / Next
To play the previous video, select twice. Selecting once will play the
current video from the beginning.
To play the next video, select ‚.
•Search
Select and play another video in the same folder. (Search Titles)
•Repeat Mode
Configure Repeat Mode. (Off, Repeat One, Repeat All)
•Picture Size
Change the screen size (Picture Size). Supported screen sizes vary
depending on the image. (Original / Mode 1 / Mode 2 / Smart View 1 /
Smart View 2)
•Settings
Option Name Operations
Picture Mode
Change the Picture Mode.
Sound Mode
Change the Sound Mode.
Audio Language
Play a video using a desired language. This feature only activates when a streaming file that
supports multiple audio formats is playing.
Information
View information about a file.
109
Available buttons and features during music playback
Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.
•Pause / Play
Pause or play music.
•Rewind / Fast Forward
Rewind or fast forward music. Speed up playback up to 3x, if required. To play the previous music file, select ∂ twice.
•Previous / Next
To play the previous music file, select twice. Selecting once will play the current music from the beginning.
To play the next music file, select ‚.
•Repeat
Configure Repeat mode. One Song plays the current music file repeatedly. All plays all files in a folder repeatedly.
•Shuffle
Enable or disable shuffle playback mode.
•Sound Mode
Change the Sound Mode.
110
Supported Subtitle and Media play le formats
Subtitle
External Internal
•MPEG-4 timed text (.ttxt)
•SAMI (.smi)
•SubRip (.srt)
•SubViewer (.sub)
•Micro DVD (.sub or .txt)
•SubStation Alpha (.ssa)
•Advanced SubStation Alpha (.ass)
•Powerdivx (.psb)
•Xsub
Container: AVI
•SubStation Alpha
Container: MKV
•Advanced SubStation Alpha
Container: MKV
•SubRip
Container: MKV
•MPEG-4 timed text
Container: MP4
Compatible image le format
Type
JPEG
4096 x 4096
PNG
BMP
111
Supported music le formats
File Extension
*.avi, *.mkv, *.asf, *.wmv, *.mp4, *.3gp, *.vro, *.mpg,
*.mpeg, *.ts, *.tp, *.trp, *.mov, *.v, *.vob, *.svi, *.divx
Supported Video Formats
•Video content will not play, or not play correctly, if there is an error in the content or the container.
•Sound or video may not work if the contents have a standard bitrate/frame rate above the compatible Frame/sec listed in the table above.
•If the Index Table is in error, the Seek (Jump) function is not supported.
•You may experience file stuttering while playing a video through a network connection.
•The menu may take longer to appear if the video’s bit rate exceeds 10Mbps.
•Some USB/digital camera devices may not be compatible with the player.
Video Decoder Audio Decoder
Supports up to H.264, Level 4.1
H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and AVCHD are not supported.
For all Video codecs except MVC, VP8, VP6:
•Below 1280 x 720: 60 frame max
•Above 1280 x 720: 30 frame max
GMC 2 over is not supported.
Supports only BD MVC Spec.
Supports up to WMA 10 Pro 5.1 channel.
WMA lossless audio is not supported.
QCELP, AMR NB/WB are not supported.
If Vorbis is only in Webm container, supports up to 2 channel.
112
Container Video Codec Resolution Frame rate
(fps)
Bit rate
(Mbps)
Audio Codec
3gpp
asf
avi
v
mkv
mov
mp4
ps
ts
vob
vro
DivX 3.11 /DivX4.X 1280 x 720 60 30 AAC
AC3
ADPCM
DD+
DTS Core
HE-AAC
LPCM
MP3
WMA
XVID
H.264 BP/MP/HP
MPEG-4 SP/ASP
WINDOW MEDIA VIDEO V9
MPEG2
MPEG1
H.263
DivX5.x
DivX6.X
113
Container Video Codec Resolution Frame rate
(fps)
Bit rate
(Mbps)
Audio Codec
3gpp
asf
avi
v
mkv
mov
mp4
ps
ts
vob
vro
DivX 3.11 /DivX4.X 1920 x 1080 30 30 AAC
AC3
ADPCM
DD+
DTS Core
HE-AAC
LPCM
MP3
WMA
XVID
H.264 BP/MP/HP
MPEG-4 SP/ASP
WINDOW MEDIA VIDEO V9
MPEG2
MPEG1
H.263
DivX5.x
DivX6.X
MOTION JPEG 640 x 480 30 8
114
Troubleshooting Guide
Chapter 12
Requirements Before Contacting Samsung Customer Service Centre
Before calling Samsung Customer Service
Centre, test your product as follows. If
the problem persists, contact Samsung
Customer Service Centre. Testing the Product
Check if your product is operating normally by using the product test function.
If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.
1
Power off both the PC and product.
2
Disconnect all the cables from the product.
3
Power on the product.
4
If No Signal is displayed, the product is operating normally.
Checking the Resolution and Frequency
Not Optimum Mode will briefly be displayed if a mode that exceeds a supported resolution is selected
(refer to Supported Resolutions).
If the screen remains blank, check the PC
system, video controller and cable.
115
Check the followings.
Installation issue (PC mode)
The screen keeps switching on and o.
Check the cable connection between the product and PC, and ensure the connection is secure.
Blank spaces are found on all four sides of the screen when
an HDMI or HDMI-DVI cable is connected to the product and
PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the
screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the
graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust
the screen settings.)
PC is shown in Source when a PC is not connected.
PC is always shown in Source irrespective of whether or not a PC is connected.
Screen issue
The power LED is o. The screen will not switch on.
Make sure that the power cord is connected.
No Signal is displayed on the screen.
Check that the product is connected correctly with a cable.
Check that the device connected to the product is powered on.
Not Optimum Mode
is displayed.
This message is displayed when a signal from the graphics card exceeds the product's maximum
resolution and frequency.
Refer to the Standard Signal Mode Table and set the maximum resolution and frequency according to
the product specifications.
The images on the screen look distorted.
Check the cable connection to the product.
116
Screen issue
The screen is not clear. The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension cable, etc) and try again.
Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky.
Check that the resolution and frequency of the PC and graphics card are set within a range compatible
with the product. Then, change the screen settings if required by referring to the Additional
Information on the product menu and the Standard Signal Mode Table.
There are shadows or ghost images left on the screen.
The screen is too bright. The screen is too dark.
Adjust Brightness and Contrast.
Screen colour is inconsistent.
Go to Picture and adjust the Colour Space settings.
White does not really look white.
Go to Picture and adjust the White Balance settings.
There is no image on the screen and the power LED blinks
every 0.5 to 1 second.
The product is in power-saving mode.
Press any key on the keyboard or move the mouse to return to the previous screen.
The product will turn o automatically.
Go to System and make sure Sleep Timer is set to Off.
If a PC is connected to the product, check the power status of the PC.
Make sure the power cable is connected properly to the product and power outlet.
If the signal from a connected device is not detected, the product automatically turns off after 10 to 15
minutes.
Picture quality of the product is dierent from the dealer
shop where it was purchased.
Use an HDMI cable to obtain high-definition (HD) picture quality.
117
Screen issue
The screen display does not look normal.
Encoded video content may cause the display to appear corrupted in scenes featuring fast moving
objects such as in a sports event or action video.
Low signal level or low picture quality may cause the display to appear corrupted. This does not mean
the product is defective.
A cell phone within a distance of one-meter radius may cause static on analogue and digital products.
The brightness and colour do not look normal.
Go to Picture and adjust the screen settings such as Picture Mode, Colour, Brightness and
Sharpness.
Go to System and adjust the Energy Saving settings.
Reset the screen settings to the default settings.
Broken lines are displayed on the edges of the screen.
If Picture Size is set to Screen Fit, change the setting to 16:9.
Lines (red, green or blue) are displayed on the screen.
These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the monitor. Contact a
Samsung Service Centre to resolve the issue.
The display looks unstable and then freezes.
The screen may freeze when a resolution other than the recommended resolution is used or if the
signal is not stable. To resolve the issue, change the PC resolution to the recommended resolution.
The screen cannot be displayed in full screen.
A scaled SD (4:3) content file can cause black bars on both sides of an HD channel screen.
A video with an aspect ratio different from the product can cause black bars at the top and bottom of
the screen.
Change the screen size setting to full screen on the product or source device.
118
Sound issue
There is no sound.
Check the connection of the audio cable or adjust the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound
card or software programme.
Video is available but there is no sound.
If an HDMI cable is connected, check the audio output settings on the PC.
Go to Sound and change Speaker Select to Internal.
If a source device is used
•Make sure the audio cable is properly connected to the audio input port on the product.
•Check the audio output settings for the source device.
(For example, if an HDMI cable is connected to the monitor, the audio setting for the cable box
may need to be changed to HDMI.)
If a DVI-HDMI cable is used, a separate audio cable is required.
If the product has a headphone port, make sure nothing is connected to it.
Reconnect the power cable to the device and then reboot the device.
There is static coming from the speakers.
Check the cable connection. Make sure a video cable is not connected to an audio input port.
Check the signal strength after connecting a cable.
Low signal level can cause corrupted sound.
119
Sound issue
There is audible sound when the volume is muted.
When Speaker Select is set to External, the volume button and mute function are disabled.
Adjust the volume for the external speakers.
Audio settings for main speakers are separate from the internal speakers on the product.
Changing or muting the volume on the product does not affect an external amplifier(decoder).
Sound from the monitor does not change after Sound Mode
is changed.
Audio settings for main speakers are separate from the internal speakers on the product.
Audio settings on a source device do not affect the internal speaker settings on the product.
There is an echo sound coming from the speakers.
Different decoding speeds between the product speakers and external speakers can cause an echo.
In this case, set Speaker Select to External.
Remote control issue
The remote control does not work.
Make sure that the batteries are correctly in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs switched on in the vicinity.
Source device issue
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
120
Other issue
Small particles are found on the edges of the product.
The particles are part of the product design. The product is not defective.
The PIP menu is not available.
The menu is enabled or disabled depending on the Source mode.
When I try to change the PC resolution, a message "The
dened resolution is not supported." appears.
The message "The defined resolution is not supported." appears if the input source resolution
exceeds the maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.
There is no sound from the speakers in HDMI mode when a
DVI-HDMI cable is connected.
DVI cables do not transmit sound data.
Make sure to connect the audio cable to the correct input jack to enable audio.
HDMI Black Level is not functioning properly on an HDMI
device with YCbCr output.
This function is available only when a source device, such as a DVD player and STB, is connected to the
product via an HDMI (RGB signal) cable.
There is no sound in HDMI mode.
Displayed picture colours may not look normal. Video or sound may not be available. This can occur if
a source device that only supports an older version of the HDMI standard is connected to the product.
If these issues occur, connect an audio cable along with the HDMI cable.
Some PC graphics cards may not automatically recognize HDMI signals that do not include sound. In
this case, manually select a sound input.
Sound input Screen mode
PC Auto PC settings
DVI PC Audio In(Stereo ports) PC settings
121
Other issue
The IR sensor is not functioning.
Make sure the sensor light turns on when a button is pressed on the remote control.
•If the sensor light does not turn on, turn the power switch off and then on again on the back of
the product.
(The power LED lights up red when the screen is switched off.)
If the sensor light still does not turn on after the power switch is turned off and then on again, an
internal jack may be disconnected.
Contact your nearest service centre to have the product serviced.
•If the sensor light that is on does not flash red when a button is pressed on the remote control,
the IR sensor may be defective.
Contact your nearest service centre to have the product serviced.
•If there is no change on the screen when a button is pressed on the remote control although the
sensor light flashes red, the mainboard may be defective.
Contact your nearest service centre to have the product serviced.
122
Q & A
Question Answer
How can I change the frequency?
Set the frequency on your graphics card.
•Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
resolution → Advanced Settings → Monitor and adjust the frequency in Monitor Settings.
•Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor
Settings.
•Windows 10: Go to Settings → System → Display → Advanced display settings → Display
adapter properties → Monitor, and adjust Screen refresh rate under Monitor settings.
How can I change the resolution?
•Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
Resolution and adjust the resolution.
•Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust Resolution and adjust the resolution.
•Windows 10: Go to Settings → System → Display → Advanced display settings, and adjust
the resolution.
How do I set powersaving mode?
•Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization →
Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•Windows 8: Set power-saving mode in Settings → Control Panel → Appearance and
Personalization → Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•Windows 10: Set power-saving mode in Settings → Personalization → Lock screen → Screen
timeout settings → Power & sleep or BIOS SETUP on the PC.
Refer to the user manual for your PC or
graphics card for further instructions on
adjustment.
123
Specications
Chapter 13
-
Size
-
Display area
H
V
General
Model Name ED65E / EM65E ED75E / EM75E
Panel Size
65 CLASS (64.5 inches / 163 cm) 75 CLASS (74.5 inches / 189 cm)
Display area
1428.48 mm (H) x 803.52 mm (V)
56.2 inches (H) x 31.6 inches (V)
1650.24 mm (H) x 928.26 mm (V)
65.0 inches (H) x 36.5 inches (V)
Audio Output
10 W + 10 W 10 W + 10 W
Model Name DC32E / DC32E-M DC40E / DC40E-M / DC40E-H
Panel Size
32 CLASS (31.5 inches / 80.1 cm) 40 CLASS (40.0 inches / 101.6 cm)
Display area
698.4 mm (H) x 392.85 mm (V)
27.5 inches (H) x 15.5 inches (V)
885.6 mm (H) x 498.15 mm (V)
34.9 inches (H) x 19.6 inches (V)
Audio Output
10 W 10 W + 10 W
124
Model Name DC48E / DC48E-M / DC48E-H DC55E / DC55E-M
Panel Size
48 CLASS (47.6 inches / 120.9 cm) 55 CLASS (54.6 inches / 138.7 cm)
Display area
1054.08 mm (H) x 592.92 mm (V)
41.5 inches (H) x 23.3 inches (V)
1209.6 mm (H) x 680.4 mm (V)
47.6 inches (H) x 26.8 inches (V)
Audio Output
10 W + 10 W 10 W + 10 W
Power Supply
This product uses 100 to 240V. Refer to the label at the back of the product as the standard voltage can vary in
different countries.
Environmental
considerations
Operating
Temperature : 0 C - 40 C (32 F - 104 F)
Humidity : 10% - 80%, non-condensing
Storage
Temperature : -20 C - 45 C (-4 F - 113 F)
Humidity : 5% - 95%, non-condensing
―Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor
settings. Monitor installation takes place automatically. However, you can customize the installation settings if desired.
―Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect
product performance.
―This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
―For detailed device specifications, visit the Samsung Electronics website.
125
-Horizontal Frequency
The time required to scan a single line
from the left to the right side of the
screen is called a horizontal cycle. The
reciprocal number of a horizontal cycle
is called horizontal frequency. Horizontal
frequency is measured in kHz.
-Vertical Frequency
The product displays a single image
multiple times per second (like a
fluorescent light) to display what the
viewer sees. The rate of a single image
being displayed repeatedly per second is
called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
Preset Timing Modes
―This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than
the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.
Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product. If the LCD product does not support 85Hz, change the vertical
frequency to 60Hz using the CDT product before you exchange it with the LCD product.
Synchronization Horizontal Frequency
30 – 81 kHz
Vertical Frequency
48 – 75 Hz
Resolution Optimum resolution
1920 x 1080 @ 60 Hz
Maximum resolution
1920 x 1080 @ 60 Hz
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the PC
does not belong to the standard signal modes, the screen may be blank with the power LED on. In such a case, change the settings according to the following table by
referring to the graphics card user manual.
Resolution Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
MAC, 1152 x 870 68.681 75.062 100.000 -/-
VESA, 640 x 480 31.469 59.940 25.175 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
126
Resolution Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA, 1152 x 864 67.500 75.000 108.000 +/+
VESA, 1280 x 720 45.000 60.000 74.250 +/+
VESA, 1280 x 800 49.702 59.810 83.500 -/+
VESA, 1280 x 1024 63.981 60.020 108.000 +/+
VESA, 1280 x 1024 79.976 75.025 135.000 +/+
VESA, 1366 x 768 47.712 59.790 85.500 +/+
VESA,1440 x 900 55.935 59.887 106.500 -/+
VESA,1600 x 900 RB 60.000 60.000 108.000 +/+
VESA,1680 x 1050 65.290 59.954 146.250 -/+
VESA,1920 x 1080 67.500 60.000 148.500 +/+
127
Appendix
Responsibility for the Pay Service
(Cost to Customers)
―When the service is requested, in spite of in warranty, we may charge you for a visit from a service
technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•If a service technician gives instructions on how to use product or simply adjusts options without
disassembling product.
•If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
•If a product is reinstalled or devices are connected additionally after installing the purchased
product for the first time.
•If a product is reinstalled to move to a different spot or to move to a different house.
•If customer requests instructions on how to use because of another company's product.
•If customer requests instructions on how to use the network or another company's programme.
•If customer requests software installation and setup for the product.
•If a service technician removes/cleans dusts or foreign materials inside of the product.
•If customer requests an installation additionally after purchasing a product through home-
shopping or online.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•External impact or drop.
•Use of supplies or separatly sold product unspecified by Samsung.
•Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
•Remodeling or repairing the product by customer.
•Using it with incorrect voltage or non-authorised electrical connections.
•Not following the "cautions" in User Manual.
Others
•If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp,
Filter, Ribbon, etc.)
―If customer requests a service in case the product has no defect, service fee may be charged. So
please read User Manual first.
Chapter 14
128
Optimum Picture Quality and Afterimage
Burn-in Prevention
Optimum Picture Quality
•Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm)
may be brighter or darker on the panel. This does not affect product performance.
-The number of sub-pixels by panel type: 6,220,800
•Run Auto Adjustment to improve the picture quality. If noise is still found even after auto
adjustment, adjust Coarse or Fine.
•Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage
burn-in or defective pixels.
-Activate power-saving mode or a dynamic screen saver if you will not be using the product for
an extended period of time.
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers
to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period
of time (more than 12 hours), a slight voltage difference may occur between the electrodes in pixels that
control the liquid crystals.
Such a voltage difference between electrodes increases with time and makes the liquid crystals thinner.
When this occurs, a previous image can remain on the screen when the pattern changes. To prevent this,
the accumulated voltage difference should be reduced.
―Afterimage burn-in should not occur when an LCD panel is operating in proper conditions.
Black Matrix
Source Drain
Data Bus-Line
TFT
Gate Pixel Electrode (ITO) Storage
Capaccitor (Cs)
Colour-Filter
Common
Electrode (ITO)
129
Preventing afterimage burn-in
―The best way to protect the product from afterimage burn-in is switching the power off or setting the
PC or system to run a screen saver when not in use. Also, Warranty service may be limited depending
on instruction guide.
•Powering Off, Screen Saver and Power Saving Mode
-Power off the product for 2 hours after using it for 12 hours.
-Go to Display Properties > Power Supply on your PC and set the product to power off as
required.
-Using a screen saver is recommended.
It is best to use a single-colour or moving-image screen saver.
•Regular colour Change
-Use 2 colours
Switch between 2 colours every 30 minutes as shown above.
FLIGHT FLIGHT
TIME TIME
OZ348
UA102 21:10
20:30
OZ348
UA102 21:10
20:30
Type 1 Type 2
•Avoid combinations of a text colour and background colour of contrasting brightness.
(Brightness: refers to the lightness or darkness of a colour which varies depending on the amount of
light emitted.)
―Avoid using grey as it may contribute to afterimage burn-in.
―Avoid using colours of contrasting brightness (black and white; grey).
FLIGHT TIME
OZ348 20:30
:
:
FLIGHT TIME
OZ348 20:30
:
:
•Regular Text colour Change
-Use bright colours of similar brightness.
Interval: Change text colour and background colour every 30 minutes
FLIGHT TIME
OZ348 20:30
:
:
FLIGHT TIME
OZ348 20:30
:
:
FLIGHT TIME
OZ348 20:30
:
:
FLIGHT TIME
OZ348 20:30
:
:
-Move and change text every 30 minutes as shown below.
FLIGHT TIME
OZ348 20:30
:
:
[ Step 3 ]
[ Step 2 ]
FLIGHT TIME
OZ348
:
:
[ Step 1 ]
20:30
-Regularly display a moving image along with a logo.
Interval: Display a moving image along with a logo for 60 seconds after using for 4 hours.
130
Licence
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Premium Sound 5.1
®
Manufactured under a license from U.S. Patent No’s: 5,956,674, 5,974,380,
5,978,762, 6,487,535, 6,226,616, 7,212,872, 7,003,467, 7,272,567, 7,668,723,
7,392,195, 7,930,184, 7,333,929 and 7,548,853. DTS, the Symbol, and DTS and
the Symbol together are registered trademarks & DTS Premium Sound | 5.1 is a
trademark of DTS, Inc. ⓒ2012 DTS, Inc. All Rights Reserved.
®
Studio Sound
Manufactured under a license from U.S. Patent No’s: 6,285,767, 8,027,477,
5,319,713, 5,333,201, 5,638,452, 5,771,295, 5,970,152, 5,912,976, 7,200,236,
7,492,907, 8,050,434, 7,720,240, 7,031,474, 7,907,736 and 7,764,802. DTS, the
Symbol, and DTS and the Symbol together are registered trademarks & DTS
Studio Sound is a trademark of DTS, Inc. ⓒ2012 DTS, Inc. All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
This DivX CertifiedⓇ device has passed rigorous testing to ensure it plays
DivXⓇ video.
To play purchased DivX movies, first register your device at vod.divx.com. Find
your registration code in the DivX VOD section of your device setup menu.
DivX CertifiedⓇ to play DivXⓇ video up to HD 1080p, including premium content.
DivXⓇ, DivX CertifiedⓇ and associated logos are trademarks of DivX, LLC and are used under
license.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 8,656,183;
8,731,369; RE45,052.
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the product menu.
Open Source Licence Notice is written only English.
For information on the Open Source Licence Notice, contact the Samsung Customer Centre or send
email to oss.request@samsung.com.
131
Terminology
480i / 480p / 720p / 1080i /
1080p____ Each of the scanning
rates above refers to the number of
effective scanning lines that decides
the screen resolution. The scanning
rate may be indicated in i (interlaced)
or p (progressive), depending on the
scanning method.
- Scanning
Scanning refers to a process of sending
pixels that form an image progressively.
A larger number of pixels will deliver a
clearer and more vivid picture.
- Progressive
In progressive scan mode, all lines
of pixels are scanned one by one
(progressively) on the screen.
- Interlaced
In interlaced scan mode, every other
line of pixels is scanned from top to
bottom first and then the remaining
lines of pixels (that were not scanned)
are scanned.
Non-interlace Mode and Interlace
Mode____ Non-interlace mode
(progressive scan) displays a horizontal
line from the top to the bottom of a
screen progressively. Interlace mode
displays the odd number lines first
and the even number lines next. Non-
interlace mode is mainly used in
monitors as it produces screen clarity
and interlace mode is mainly used in
TVs.
Dot Pitch____ The product and screen
consist of red, green and blue dots.
A shorter distance between the dots
produces a higher resolution. Dot pitch
refers to the distance between the
shortest distance between dots of the
same colour. Dot pitch is measured in
millimeters.
Vertical Frequency____ The product
displays a single image many times
per second (like a fluorescent light that
flickers) to display an image for a viewer
to see. The rate of a single image being
displayed repeatedly per second is
called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
E.g. 60Hz refers to a single image being
displayed 60 times in one second.
Horizontal Frequency____ The time
required to scan a single line from the
left to the right side of the screen is
called a horizontal cycle. The reciprocal
number of a horizontal cycle is called
horizontal frequency. Horizontal
frequency is measured in kHz.
Source____ Input source refers to a
video source device connected to the
product such as a camcorder or video
or DVD player.
Component ports (green, blue and
red)____ The component ports, which
identify, transmit and receive contrast
signals, provide superior picture quality
to any other video connection methods.
Plug & Play____ Plug & Play is a
function that allows the automatic
exchange of information between a
monitor and PC to produce an optimum
display environment. The product uses
VESA DDC (international standard) to
execute Plug & Play.
Resolution____ Resolution is the
number of horizontal dots (pixels) and
vertical dots (pixels) that form a screen.
It represents the level of display detail.
A higher resolution enables more
data to be displayed on the screen
and is useful to perform multiple tasks
simultaneously.
E.g. A resolution of 1920 X 1080 consists
of 1,920 horizontal pixels (horizontal
resolution) and 1,080 vertical pixels
(vertical resolution).
HDMI (High Definition Multimedia
Interface)____ It is an interface that
can be connected to a digital audio
source as well as a high-definition video
source by using a single cable without
compression.
Multiple Display Control (MDC)____
MDC (Multiple Display Control) is an
application that allows multiple display
devices to be controlled simultaneously
using a PC. Communication between
a PC and monitor takes place using
RS232C (serial data transmission) and
RJ45 (LAN) cables.