Samsung QND-6010R User Manual
Displayed below is the user manual for QND-6010R by Samsung which is a product in the Security Cameras category. This manual has pages.
Related Manuals
NETWORK CAMERA
User Manual
QND-6010R/6020R/6030R,
QNO-6020R/6030R,
QNV-6010R/6020R/6030R
Copyright
©2016 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their
respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin reserves the
right to change the contents of this document without prior notice.
Design and specications are subject to change without prior notice.
The initial administrator ID is “admin” and the password should be set when logging in for the rst time.
Please change your password every three months to safely protect personal information and to prevent the damage of the information
theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
Network Camera
User Manual
English _3
●●OVERVIEW
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents
as they may deform or cause damage to the product.)
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated
from 12 Vdc, min. current for each product.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE
VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance
with the installation instructions.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the product.
overview
overview
4_ overview
Class construction
An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a
protective earthing connection.
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as
sunshine, fire or the like.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in
your location.
When used outside of the U.S., it may be used HAR code with fittings of an approved
agency is employed.
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that contained in
the operating instructions unless you are qualified to do so.
Please use the input power with just one camera and other devices must not be connected.
The ITE is to be connected only to PoE networks without routing to the outside plant.
Please read the following recommended safety precautions carefully.
yDo not place this apparatus on an uneven surface.
yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or
heavy cold area.
yDo not place this apparatus near conductive material.
yDo not attempt to service this apparatus yourself.
yDo not place a glass of water on the product.
yDo not install near any magnetic sources.
yDo not block any ventilation openings.
yDo not place heavy items on the product.
yPlease wear protective gloves when installing/removing the camera.
The high temperature of the product surface may cause a burn.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
yReference : In case of providing information for helping of product’s usages
yNotice : If there’s any possibility to occur any damages for the goods and human caused by
not following the instruction
Please read this manual for the safety before using of goods and keep it in the safe place.
English _5
●●OVERVIEW
CONTENTS
overview
3
3 Important Safety Instructions
6 Product Features
6 Recommended PC Specifications
6 Recommended Micro SD/SDHC/SDXC
Memory Card Specifications
6 NAS recommended specs
7 What’s Included
8 At a Glance (QND-6010R/6020R/6030R)
10 At a Glance (QNO-6020R/6030R)
11 At a Glance (QNV-6010R/6020R/6030R)
installation & connection
13
13 Installation (QND-6010R/6020R/6030R)
14 Installation (QNO-6020R/6030R)
15 Installation (QNV-6010R/6020R/6030R)
18 Inserting/Removing a Micro SD Memory
Card
19 Memory Card Information (Not Included)
20 Connecting with other Device
network connection and
setup
23
23 Connecting the Camera Directly to Local
Area Networking
23 Connecting the Camera Directly to a DHCP
Based DSL/Cable Modem
24 Connecting the Camera Directly to a
PPPoE Modem
24 Connecting the Camera to a Broadband
Router with the PPPoE/Cable Modem
25 Buttons used in IP Installer
25 Static IP Setup
27 Dynamic IP Setup
27 Port Range Forward (Port Mapping) Setup
28 Connecting to the Camera from a Shared
Local PC
28 Connecting to the Camera from a Remote
PC via the Internet
web viewer
29
29 Connecting to the Camera
30 Password setting
30 Login
30 Plug-in support specifications for each
browser
31 Installing WebViewer Plugin
31 Using a Plug-in Free Webviewer
31 Using the Live Screen (Plug-in Free
Webviewer)
32 Using the Live Screen (Plug-in Webviewer)
34 Playing the recorded video (Plug-in Free
Webviewer)
36 Playing the recorded video (Plug-in
Webviewer)
setup screen
39
39 Setup
39 Basic Setup
43 Audio & Video setup
48 Network Setup
51 Event Setup
53 NAS (Network Attached Storage) guide
58 System Setup
appendix
60
60 Specification
62 Product Overview
63 Troubleshooting
64 Open Source Announcement
overview
6_ overview
PRODUCT FEATURES
•Dustproof/Waterproof (IP66) (QNO-6020R/6030R, QNV-6010R/6020R/6030R)
The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing
it to rain.
•IR mode
If the IR indicator turns on, the product switches to the IR mode for preventing an object from being too bright,
which helps you identify the object in near distance.
•Supports 2 megapixel resolution videos
•Multi-Streaming
This network camera can display videos in different resolutions and qualities simultaneously using different
CODECs.
•Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
•Alarm
When an event occurs, video is either sent to the email address registered by the user, sent to the FTP server,
saved in a Micro SD card or NAS, or a signal is sent to the alert output terminal.
•Tampering Detection
Detects tempering attempts on video monitoring.
•Defocus detection function
Detects the defocus phenomenon of the camera lens.
•Motion Detection
Detects motion from the camera’s video input.
•Auto Detection of Disconnected Network
Detects network disconnection before triggering an event.
•ONVIF Compliance
This product supports ONVIF Profile S&G.
For more information, refer to www.onvif.org.
RECOMMENDED PC SPECIFICATIONS
•CPU : Intel(R) Core(TM) i7 3.4 GHz or higher
•Supported OS : Windows 7, 8.1, 10, Mac OS X 10.9, 10.10, 10.11
•Plug-in free web viewer
Supported web browsers : Google Chrome 47, MS Edge 20
•Plug-in Webviewer
Supported web browsers : MS Explorer 11, Mozilla Firefox 43, Apple Safari 9 ※ Mac OS X only
•VGA : PCIe 256MB GDDR3 video graphics card or higher
RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD
SPECIFICATIONS
•Recommended capacity : 4GB ~ 128GB (uhs-1 class)
•For your camera, we recommend you use a memory card from the following manufacturers:
Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend
NAS RECOMMENDED SPECS
•Recommended capacity : 200GB or higher is recommended.
•Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.
•For this camera, you are recommended to use a NAS with the following manufacturer’s specs.
Recommended products Available sizes
Netgear NAS A maximum of 16 cameras can access simultaneously.
Synology NAS A maximum of 16 cameras can access simultaneously.
J
`When you use Netgear’s NAS equipment, do not allocate the capacity for use.
`If you use NAS equipment for purposes other than video saving, the number of accessible cameras may be reduced.
English _7
●●OVERVIEW
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
(As for each sales country, accessories are not the same.)
Appearance Item Name Quantity Description Model Name
NETWORK
ACT LINK
FRONT
RESET
3. 4. GND
2. ALM OUT
1. ALM IN
5. AUDIO IN
DC12V
Camera
1
QND-6010R/6020R
/6030R
1
QNO-6020R/6030R
AC 24V / DC 12V
RESET
VIDEO
F
W
AF
T
N
+ -
5. AUDIO IN
3.4. GND
2.ALM OUT
1.ALM IN
RESET
DC12V
1
QNV-6010R/6020R/
6030R
Instruction book,
Installer S/W CD
1
QND-6010R/6020R
/6030R,
QNO-6020R/6030R,
QNV-6010R/6020R/
6030R
Quick Guide
(Optional)
1
QND-6010R/6020R
/6030R,
QNO-6020R/6030R,
QNV-6010R/6020R/
6030R
Warranty card
(Optional)
1
QND-6010R/6020R
/6030R,
QNO-6020R/6030R,
QNV-6010R/6020R/
6030R
Template
1
Product installation guide
QND-6010R/6020R
/6030R,
QNO-6020R/6030R,
QNV-6010R/6020R/
6030R
Power Terminal Block
1
Plugged in the power plug
QND-6010R/6020R
/6030R,
QNV-6010R/6020R/
6030R
Appearance Item Name Quantity Description Model Name
Machine Screws
2
Used for assembling the dome case
when installing the product on the pipe,
wall mount, etc. or blocking a hole.
QND-6010R/6020R
/6030R,
QNV-6010R/6020R/
6030R
L Wrench
1
Used to control the direction of the
camera / Used to remove and replace
the dome cover
QNO-6020R/6030R,
QNV-6010R/6020R/
6030R
Tapping Screw
2
Used for installation on the wall or
ceiling
QND-6010R/6020R
/6030R,
QNV-6010R/6020R/
6030R
3 QNO-6020R/6030R
Alarm cable
1
Used when connecting to an alarm QND-6010R/6020R
/6030R
RJ45 waterproof accessory
1
Used to install in humid places QNO-6020R/6030R
Sunshield
1
It protects the camera from the direct
sunlight. QNO-6020R/6030R
Sunshield Hold
1
It fixes the sunshield with the camera. QNO-6020R/6030R
Card-type moisture absorbent
3
Attached when installed.
QNO-6020R/6030R
1
QNV-6010R/6020R/
6030R
overview
8_ overview
AT A GLANCE (QND-6010R/6020R/6030R)
Appearance
Item Description
a
Dome cover Case cover used to protect the lens and the main unit.
b
Camera Case Housing part that covers the camera body.
c
Microphone hole Microphone is embedded.
NETWORK
ACT LINK
FRONT
RESET
3. 4. GND
2. ALM OUT
1. ALM IN
5. AUDIO IN
DC12V
a
b
c
Appearance Item Name Quantity Description Model Name
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
Power Cable
1
Used to plug into the power port QNV-6010R/6020R/
6030R
Audio/alarm cable
1
Used to connect with the audio and
alarm port
QNV-6010R/6020R/
6030R
Cable bush
1
Used to connect the LAN cable with a
diameter of Ø7~8.5.
QNV-6010R/6020R/
6030R
Plastic Anchor
2
For fixing a screw, Inserted in a hole
(reinforced anchoring force)
QNV-6010R/6020R/
6030R
Options (not included)
Pole mount bracket Cylindrical pole mounting bracket QNO-6020R/6030R
English _9
●●OVERVIEW
Components Item Description
a
Inside cover Protective cover for the main body.
b
Illumination Sensor Detects incoming light to control the IR LED.
c
Lens Lens for the camera.
d
IR LED These infrared LED’s are controlled by the illumination sensor.
e
Reset Button
The button restores all camera settings to the factory default.
Press and hold for about 5 seconds to reboot the system.
J If you reset the camera, the network settings will be adjusted so that DHCP can be
enabled. If there is no DHCP server in the network, you must run the IP Installer
program to change the basic network settings such as IP address, Subnet mask,
Gateway, etc., before you can connect to the network.
f
Alarm I/O Port
ARM-IN Used to connect the alarm input sensor or external day/night sensor.
ARM-OUT Used to connect the alarm output signal.
GND These are common ports to connect alarm input/output signals.
g
Microphone hole Microphone is embedded.
h
Power Port Port for power terminal block.
i
Micro SD Memory Card
Compartment Compartment for the Micro SD memory card.
j
Network Port Used to connect the PoE or Ethernet cable for network connection.
NETWORK
ACT LINK
DC 12V
FRONT
ji
NETWORK
ACT LINK
FRONT
RESET
3. 4. GND
2. ALM OUT
1. ALM IN
DC12V
e
f
h
g
cdba
overview
10_ overview
Components
Item Description
a
Power Port Used to plug the power cable.
b
Alarm I/O Port
ARM-OUT Used to connect the alarm output signal.
GND These are common ports to connect alarm input/output signals.
ARM-IN Used to connect the alarm input sensor or external day/night sensor.
c
Network Port Used to connect the PoE or Ethernet cable for network connection.
d
Audio In Jack Used to connect to a microphone.
CAUTION:Be ware of the
Rated Voltage and Polarity
of the power connection.
a
b
c
d
AT A GLANCE (QNO-6020R/6030R)
Appearance
Item Description
a
Micro SD card slot (Internal space of the product) This is a slot in which you can insert a Micro SD card.
b
Reset Button
The button restores all camera settings to the factory default.
Press and hold for about 5 seconds to reboot the system.
J If you reset the camera, the network settings will be adjusted so that DHCP can be
enabled. If there is no DHCP server in the network, you must run the IP Installer
program to change the basic network settings such as IP address, Subnet mask,
Gateway, etc., before you can connect to the network.
c
Sunshield Hold It fixes the sunshield with the camera.
d
Sunshield It protects the camera from the direct sunlight.
RESET
b ca
d
English _11
●●OVERVIEW
Components
AT A GLANCE (QNV-6010R/6020R/6030R)
Appearance
Item Description
a
Dome cover Case cover used to protect the lens and the main unit.
b
Camera Case Housing part that covers the camera body.
AC 24V / DC 12V
RESET
VIDEO
F
W
AF
T
N
+ -
5. AUDIO IN
3.4. GND
2.ALM OUT
1.ALM IN
RESET
DC12V
a
b
RESET
NETWORK
ACT LINK
g h
DC12V
5. AUDIO IN
3.4. GND
2.ALM OUT
1.ALM IN
RESET
f
d
e
bca
overview
12_ overview
Item Description
a
Illumination Sensor Detects incoming light to control the IR LED.
b
Lens Lens for the camera.
c
IR LED These infrared LED’s are controlled by the illumination sensor.
d
Power Port Port for power terminal block.
e
Audio and alarm cable port Terminal to which the audio and alarm cable is connected in order to connect with an
external alarm device/microphone.
f
Reset Button
The button restores all camera settings to the factory default.
Press and hold for about 5 seconds to reboot the system.
J If you reset the camera, the network settings will be adjusted so that DHCP can be
enabled. If there is no DHCP server in the network, you must run the IP Installer
program to change the basic network settings such as IP address, Subnet mask,
Gateway, etc., before you can connect to the network.
g
Micro SD Memory Card
Compartment Compartment for the Micro SD memory card.
h
Network Port Used to connect the PoE or Ethernet cable for network connection.
English _13
●●INSTALLATION & CONNECTION
installation & connection
INSTALLATION (QND-6010R/6020R/6030R)
Precautions before installation
Ensure you read out the following instructions before installing the camera:
•It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera
including the installation bracket.
•Stuck-in or peeled-off cables can cause damage to the product or a fire.
•For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
Disassembling
1. Use one hand to hold the camera’s bottom part and turn the cover
counterclockwise with another hand to separate it.
2. Lift up the inner cover to separate it.
Installation
1. Attach the installation template to the selected area and punch 3
holes as shown in the figure.
2. Using 2 tapping screws provided, fix the camera at 2 holes drilled
with a template.
`Set the < > mark imprinted on the camera to face the direction of camera
monitoring.
3. Connect the camera internal terminal with the corresponding
cable.
4. Adjust the lens in a desired direction by referring to the “Adjusting
the monitoring direction for the camera” section. (page 17)
J
`We recommend you not to touch the lens as the camera lens has been
properly focused in the final process of manufacturing. If so, the lens may be
out of focus or stained by alien substances.
5. Please connect the inner cover to the main body.
6. While grabbing the bottom side of the camera with your hand, please
grab and push its cover with the other hand to align the two arrow signs,
as shown in the figure.
J
`To assemble the dome cover, make the arrows match each other and press the
cover firmly.
If the dome cover is rotated during assembly or is assembled incorrectly, diffused
reflection may occur or the lens section may rotate, which will cause the shooting
range to be changed.
`Make sure that the dome cover is correctly connected to the bottom part as shown
in the figure.
If the snap-fit is not connected correctly, the dome cover may fall, which may cause
injury.
NETWORK
ACT LINK
FRONT
RESET
3. 4. GND
2. ALM OUT
1. ALM IN
5. AUDIO IN
DC12V
Dome Cover
NETWORK
ACT LINK
FRONT
RESET
3. 4. GND
2. ALM OUT
1. ALM IN
DC12V
NETWORK
ACT LINK
FRONT
RESET
3. 4. GND
2. ALM OUT
1. ALM IN
DC12V
NETWORK
ACT LINK
FRONT
RESET
3. 4. GND
2. ALM OUT
1. ALM IN
5. AUDIO IN
DC12V
NETWORK
ACT LINK
FRONT
RESET
3. 4. GND
2. ALM OUT
1. ALM IN
5. AUDIO IN
DC12V
installation & connection
14_ installation & connection
INSTALLATION (QNO-6020R/6030R)
J
`This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are
recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Precautions before installation
Ensure you read out the following instructions before installing the camera:
•It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera
including the installation bracket.
•Stuck-in or peeled-off cables can cause damage to the product or a fire.
•For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
Installation
1. Attach the installation template at a desired location and make 3
holes the same size as shown in the picture below.
2. Insert and fasten 3 tapping screws provided into 3 holes to secure
the camera.
3. Connect the appropriate cables with camera terminals.
4. Adjust the camera direction using the L wrench provided.
J
`When you adjust the camera position using a bracket, please loosen the
bracket screw, adjust the camera, and tighten it. If you attempt to adjust it
forcibly while the screw is tight, it may result in a scratch or other problems.
How to connect the RJ45 waterproof cable to a LAN cable
1. Insert it through the arrow direction.
2. Connect the LAN connector (male) to the cable.
3. Connect the RJ45 modular jack (female) to the RJ45 connector
(male).
J
`Please, keep each of the parts separated.
4. Assemble by rotating the RJ45 modular jack (female) and the RJ45
protection cover clockwise (Follow the arrow).
5. Assemble by rotating RJ45 protection cover and back cover
clockwise (Follow the arrow).
When the back cover is assembled, the cable waterproof gasket is
tightly attached to the cable to make it waterproof.
J
`You must fully assemble it to rotate the back cover up to the end of the screw
thread of the RJ45 connector.
Mounting Template
Cable Line
RJ45 connector
(male)
RJ45 modular
jack (female) Rubber ring
RJ45 connector
protection cover
Back cover
Cable waterproof
gasket
Rubber ring
English _15
●●INSTALLATION & CONNECTION
Installation
1. Using the template provided as an accessory, drill the screw
installation hole(diameter of 6mm, minimal depth of 55mm) and
firmly insert the plastic anchor provided as an accessory to the
end.
2. Fit the bottom hole to the anchor hole and insert and fix the taping
screw (M4.5xL50).
3. Connect and arrange the necessary cables lest that they should
be damaged or twisted while installing the camera.
4. Adjust the lens in a desired direction by referring to the “Adjusting
the monitoring direction for the camera” section. (page 17)
5. Close the dome cover.
`Securely fasten the fastening bolt using an L wrench to prevent water from leaking.
Connecting the LAN cable
1. Remove the dome cover and the case.
2. Pull out the long projected part of the rubber plug on the bottom and
remove it as shown in the figure.
J
`Use an appropriate cable bush for the LAN cable to be connected.
-Basic camera : Use the cable with a diameter of Ø5~6.5.
-Components provided : Use the cable with a diameter of Ø7~8.5.
3. Insert the LAN cable into the large hole made by removing the projected
part of the rubber plug in step 2 above.
4. Remove the sheath with a cable cutter, and align the cables.
5. Connect the LAN cable with a LAN connector, and insert it into the LAN
tool.
6. Connect the finished cable to the Ethernet port.
Outdoor installation
When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be
purchased in stores) so that water does not leak from the gap of the cable connected to the outside.
1. Connect the power, I/O, AUDIO, and LAN cables.
2. Wrap the black cable jacket (Area A) and the cable connection
area with waterproof (butyl rubber) tape so that more than half of
the butyl rubber tape is overlapped.
J
`If the cable jacket is not waterproofed properly, then it can directly cause
leakage. Make sure to protect the cable with a dense layer of taping.
`Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.
INSTALLATION (QNV-6010R/6020R/6030R)
J
`This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are
recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Precautions before installation
Ensure you read out the following instructions before installing the camera:
•It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera
including the installation bracket.
•Stuck-in or peeled-off cables can cause damage to the product or a fire.
•For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
Disassembling
1. Using the L wrench provided, turn the 2 fastening bolts
on the dome cover counter clockwise to remove the
cover.
Camera
Camera
Camera
System
System
System
AA
5. AUDIO IN
3.4. GND
2.ALM OUT
1.ALM IN
RESET
Dome cover
Camera Case
Bolts
Camera Body
5. AUDIO IN
3.4. GND
2.ALM OUT
1.ALM IN
RESET
RESET
NETWORK
ACT LINK
RESET
NETWORK
ACT LINK
installation & connection
16_ installation & connection
Connecting the audio/alarm cable and power cable
1. Remove the dome cover and the case.
2. Pull out the rubber plug on the bottom as shown in the figure.
3. Insert the alarm/audio cable through the hole created by removing the
rubber cap in No. 2, and connect the cable to the alarm terminal.
4. Align the cable so that it should not be damaged or jammed when
installing the camera.
5. Put the rubber cap located on the alarm/audio cable in the hole.
6. Insert the power cable into the small-sized hole through the long, carved
groove.
7. Connect the power cable to the power terminal block.
8. Adjust the lens in a desired direction by referring to the “Adjusting the
monitoring direction for the camera” section.
(page 17)
9. Attach the dome cover.
RESET
NETWORK
ACT LINK
RESET
NETWORK
ACT LINK
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
RESET
NETWORK
ACT LINK
Attaching to the unbundled adapter
Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation
site or for your convenience.
1. Remove the dome cover from the case by referring to the “Disassembling” section. (page
15
)
2. Use the provided machine screw to fix the camera case to the unbundled adapter.
3. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the
camera.
4. Install the camera body in the reverse order of “Disassembling”.
5. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the
camera” section. (page
17
)
6. Close the dome cover.
`Securely fasten the fastening bolt using an L wrench to prevent water from leaking.
Outdoor installation
When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be
purchased in stores) so that water does not leak from the gap of the cable connected to the outside.
1. Connect the power, I/O, BNC, and LAN cables.
2. Wrap the black cable jacket (Area A) and the cable connection area
with waterproof (butyl rubber) tape so that more than half of the
butyl rubber tape is overlapped.
J
`If the cable jacket is not waterproofed properly, then it can directly cause
leakage. Make sure to protect the cable with a dense layer of taping.
`Waterproof butyl tape is made of butyl rubber that can be stretched to twice
its normal length.
Camera
Camera
Camera
System
System
System
AA
English _17
●●INSTALLATION & CONNECTION
Optional Accessories for Installation
For your easier installation, you can purchase appropriate optional accessories available.
1. WALL MOUNT ADAPTOR(SBP-300WM or SBP-300WM1)/
HANGING MOUNT(QND-6010R/6020R/6030R : SBP-300HM8)
This adaptor is used when installing the dome camera onto a
wall.
2. CEILING MOUNT ADAPTOR(SBP-300CM)/HANGING MOUNT(QND-
6010R/6020R/6030R : SBP-300HM8)
This adaptor is used when installing the dome camera on a concrete
ceiling.
3. POLE MOUNT ADAPTOR(SBP-300PM)
This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-
300WM1) installation on a pole whose diameter is bigger than 80mm.
4. CORNER MOUNT ADAPTOR (SBP-300KM)
This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or
SBP-300WM1) installation on the corner of wall joint.
Adjusting the monitoring direction for the camera (QND-6010R/6020R/6030R,
QNV-6010R/6020R/6030R)
`Adjusting the monitoring direction
You can adjust the camera direction only when the camera is fixed on the ceiling.
Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the
lens on its axis is called Rotation.
- The effective range of pan is a total of 350 degrees.
- The effective range of rotation is a total of 355 degrees.
- The effective range of tilt is a total of 67 degrees.
J
`The image can be covered up by the camera case depending on the angle.
`Do not forcefully turn the focus/zoom lens after the dome case is disassembled.
Otherwise, it may cause an incorrect focus due to a motor failure.
`Methods of adjustment
1. After installing the camera, adjust the panning angle in consideration of the monitoring direction.
2. Set the horizontal angle so that the image is not reversed.
3. Adjust the tilt angle so that the camera faces toward the monitoring object.
5. AUDIO IN
3.4. GND
2.ALM OUT
1.ALM IN
RESET
Pan
Tilt
Lens rotation
installation & connection
18_ installation & connection
INSERTING/REMOVING A MICRO SD MEMORY CARD
J
`Disconnect the power cable from the camera before inserting the Micro SD memory card.
`Do not insert the Micro SD memory card while it’s upside down by force.
Otherwise, it may damage the Micro SD memory card.
`
When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.
`
Disassembly of the product cover should be finished within 5 minutes, or there will be the risk of internal dew condensation.
Inserting a Micro SD Memory Card (QNO-6020R/6030R)
1. Turn the front cover to the UNLOCK [ ] direction.
2. Pull and separate the front cover.
3. Insert a Micro SD card in the arrow direction shown in the figure.
RESET
RESET
Inserting a Micro SD Memory Card (QND-6010R/6020R/6030R, QNV-6010R/6020R/
6030R)
1. Separate the Dome cover of the camera.
2. Insert a Micro SD card in the arrow direction shown in the figure.
RESET
NETWORK
ACT LINK
RESET
NETWORK
ACT LINK
<QNV-6010R/6020R/6030R>
NETWORK
ACT LINK
DC 12V
FRONT
NETWORK
ACT LINK
DC 12V
FRONT
<QND-6010R/6020R/6030R>
English _19
●●INSTALLATION & CONNECTION
Removing a Micro SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory
card from the slot.
RESET
NETWORK
ACT LINK
RESET
NETWORK
ACT LINK
<QNV-6010R/6020R/6030R>
NETWORK
ACT LINK
DC 12V
FRONT
NETWORK
ACT LINK
DC 12V
FRONT
<QND-6010R/6020R/6030R>
RESET
RESET
<QNO-6020R/6030R>
Micro SD/SDHC/SDXC
Contacts
J
`Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably from the slot when released.
`Before removing your Micro SD memory card, turn off the camera or go to <Storage>, turn the device off, and press the [Apply
( )] button. (Page 52)
`If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or
damaged.
MEMORY CARD INFORMATION (NOT INCLUDED)
What is a memory card?
The memory card is an external data storage device that has been developed to offer an entirely new way to
record and share video, audio, and text data using digital devices.
Selecting a memory card that’s suitable for you
Your camera supports Micro SD/SDHC/SDXC memory cards.
You may, however, experience compatibility issues depending on the model and make of the memory card.
For your camera, we recommend you use a memory card from the following manufacturers:
Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend
It is recommended to use a 4 to 128GB (uhs-1 class) memory card for this camera.
Playback performance can be affected depending on the speed of memory card, so use the high-speed
memory card.
Memory Card Components
installation & connection
20_ installation & connection
CONNECTING WITH OTHER DEVICE
CAUTION:Be ware of the
Rated Voltage and Polarity
of the power connection.
<QNO-6020R/6030R>
Ethernet
Power
NETWORK
ACT LINK
FRONT
RESET
3. 4. GND
2. ALM OUT
1. ALM IN
DC12V
NETWORK
ACT LINK
<QND-6010R/6020R/6030R>
Power
Ethernet
<QNV-6010R/6020R/6030R>
RESET
NETWORK
ACT LINK
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
Ethernet
Power
Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the
camera.
J
`If both PoE and DC 12V are applied simultaneously, the product will be supplied with power from PoE.
-You can also use a router featuring PoE to supply power to the camera.
-Use PoE that is compliant with the IEEE 802.3af protocols.
-It is advisable to use only one power source from PoE and DC 12V.
`Be careful not to reverse the polarity when you connect the power cable.
`If you want to connect an external device, you must turn off the external device before proceeding.
Power Cable Specification for Each Model
In case of DC 12V Input:
Wire Type (AWG) #22 #20 #18
Cable Length (Max.) 24m 38m 60m
Network Cable Specification
Item Contents Remark
Connector RJ45
Ethernet 10/100BASE-T 10/100 Mbps
Cable UTP Category 5e
Max Distance 100M
PoE Support IEEE 802.3af
English _21
●●INSTALLATION & CONNECTION
Connecting to Audio Input
1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the
microphone is connected to.
M
`You can use the built-in microphone in the camera without connecting an external microphone.
(only available in QND-6010R/6020R/6030R)
2. Check the specifications for audio input.
•Audio Codec
- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate:
16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz)
•Full duplex Audio
•Audio in (QND-6010R/6020R/6030R) : Selectable (Built-in microphone), Supported voltage: 2.5VDC
(4mA), Input impedance: 2K Ohm
•Audio in (QNO-6020R/6030R, QNV-6010R/6020R/6030R) : Selectable (microphone/Line-in), Supported
voltage: 2.5VDC (4mA), Input impedance: 2K Ohm
Network
Speaker
Microphone
Microphone
Microphone
Microphone
Microphone
Amp
Amp
PC
Connecting to the I/O port box
Connect the Alarm I/O cable to the corresponding port of the port box.
<QND-6010R/6020R/6030R>
Sensor Alarm
(Warning lamp)
<QNO-6020R/6030R>
CAUTION:Be ware of the
Rated Voltage and Polarity
of the power connection.
SensorAlarm
(Warning lamp)
installation & connection
22_ installation & connection
<QNV-6010R/6020R/6030R>
5. AUDIO IN
3.4. GND
2.ALM OUT
1.ALM IN
RESET
Sensor Alarm
(Warning lamp)
•ALARM-IN : Used to connect the alarm input sensor or external day/night sensor.
•ALARM-OUT : Used to connect the alarm output signal.
•GND : Common port for alarm in/output signal.
J
`If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open
collector method, it may cause malfunction.
Refer to the “Alarm Out Wiring Diagram” when connecting devices that exceed the voltage and current specifications. (page
22)
To connect the external sensor
Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the
other strand to the [GND] port.
Alarm In Wiring Diagram
To connect the alarm out
If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by
using the open collector method, it may cause malfunction.
Refer to the alarm out connection diagram below when connecting devices that exceed the voltage and
current specifications.
Alarm Out Wiring Diagram
Sensor
GND
RESISTORALARM IN (5mA SINK)
RESISTOR RESISTOR
VCC_3.3V
DIODE
GND
MLCC TRANSISTOR
External
connection
Inside of the camera
Warning lamp /
Siren power
Warning lamp /
Siren
(
-
) (
+
)
ALARM OUT (12VDC 20mA MAX)
RESISTOR 10K ohm
DIODE
RELAY
DC 5V or 3.3V
TRANSISTOR
GND
GND
TRANSISTOR
External connection Inside of the camera
GND
RESISTOR
English _23
●●NETWORK CONNECTION AND SETUP
network connection and setup
You can set up the network settings according to your network configurations.
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING
Connecting to the camera from a local PC in the LAN
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.
M
`A remote PC in an external Internet out of the LAN network may not be able to connect to the camera installed in the intranet
if the port-forwarding is not properly set or a firewall is set.
In this case, to resolve the problem, contact your network administrator.
`In the IP installer, you can use the initial password, “4321” to set IP Address, Subnet Mask, Gateway, HTTP Port, VNP Port, IP
type. After changing the network interface, for better security, access the web viewer and change the password.
`By factory default, the IP address will be assigned from the DHCP server automatically.
If there is no DHCP server available, the IP address will be set to 192.168.1.100.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page 25)
CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE
MODEM
1. Connect the user PC directly with the network camera.
2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on
your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Basic] – [IP & Port], and set the IP type to [DHCP].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
M
`For configuring the DDNS settings, refer to “DDNS”. (page 48)
`For registering the DDNS settings, refer to “Registering with DDNS”. (page 48)
`Refer to “IP & Port” for how to setup IP. (page 42)
<Local Network>
Camera
Camera
Local PC
INTERNET
External Remote PC
DDNS Server
(Data Center, KOREA)
Camera External Remote PC
DDNS Server
(Data Center, KOREA)
DSL/Cable Modem
INTERNET
network connection and setup
24_ network connection and setup
CONNECTING THE CAMERA DIRECTLY TO A PPPoE MODEM
1. Connect the user PC directly with the network camera.
2. Run the IP Installer and change the IP address of the camera so that you can use the web browser on
your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Basic] – [IP & Port] Setup Page, set the IP type to [PPPoE], and enter the network service’s ID
and password.
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
M
`For configuring the DDNS settings, refer to “DDNS”. (page 48)
`For registering the DDNS settings, refer to “Registering with DDNS”. (page 48)
`Refer to “IP & Port” for how to setup IP. (page 42)
CONNECTING THE CAMERA TO A BROADBAND ROUTER WITH THE
PPPoE/CABLE MODEM
This is for a small network environment such as homes, SOHO and ordinary shops.
Configuring the network settings of the local PC connected to a Broadband Router
Configuring the network settings of the local PC connected to a Broadband Router, follow the instructions
below.
•Select : <Network> <Properties> <Local Area Connection> <General> <Properties>
<Internet Protocol (TCP/IP)> <Properties> <Obtain an IP address automatically> or <Use the
following IP address>.
•Follow the instructions below if you select <Use the following IP address>:
ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1
IP address : 192.168.1.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1
IP address : 192.168.0.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.1
ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1
IP address : 192.168.xxx.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.xxx.1
M
`For the address of the Broadband Router, refer to the product’s documentation.
`For more information about port forwarding of the broadband router, refer to “Port Range Forward (Port Mapping) Setup”.
(Page 27)
Camera
Camera
Local PC
Broadband
Router
PPPoE or
Cable Modem
PPPoE or
Cable Modem External Remote PC
DDNS Server
(Data Center, KOREA)
INTERNET
Camera External Remote PC
DDNS Server
(Data Center, KOREA)
PPPoE Modem
INTERNET
English _25
●●NETWORK CONNECTION AND SETUP
BUTTONS USED IN IP INSTALLER
Item Description
a
Device Name
Model name of the connected camera.
Click the column to sort the list by model name.
However, search will be stopped if clicked during the search.
b
Alias This function is not currently implemented.
c
Mode Displays either <Static>, <Dynamic> or <PPPoE> for the current network connection
status.
d
MAC(Ethernet) Address
Ethernet address for the connected camera.
Click the column to sort the list by Ethernet address.
However, search will be stopped if clicked during the search.
e
IP Address
IP address.
Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
f
Protocol
Network setting for the camera.
The factory default is “IPv4”.
Cameras with the IPv6 setting will be displayed “IPv6”.
g
URL
DDNS URL address enabling access from the external Internet.
However, this will be replaced with the <IP Address> of the camera if DDNS registration
has failed.
h
IPv4 Scans for cameras with the IPv4 setting.
Item Description
i
IPv6 Scans for cameras with the IPv6 setting.
Activated in an IPv6 compliant environment only.
j
Search Scans for cameras that are currently connected to the network.
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
k
Auto Set The IP Installer automatically configures the network settings.
l
Manual Set You should configure the network settings manually.
m
Exit Exits the IP Installer program.
M
`
For the IP installer, use only the installer version provided in the installation CD or use the latest one if available. You can download
the latest version from the Hanwha Techwin web site.
STATIC IP SETUP
Manual Network Setup
Run <IP Installer_v2.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M
`For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function.
1. Select a camera in the search list.
Check the MAC address of the camera on the camera’s label.
Both the [Auto Set] and [Manual Set] buttons will be
activated.
2. Click [Manual Set].
The Manual Setting dialog appears.
<IP Address>, <Subnet Mask>, <Gateway>, <HTTP
Port>, and <VNP Port> of the camera are displayed in the
preset values.
3. In the <Address> pane, provide the necessary information.
•MAC (Ethernet) Address : The MAC address imprinted on
the camera label is automatically displayed and requires no
user setting.
M
`IP related parameters can be set only when DHCP is not checked.
a b c d e f g
h i j k l m
network connection and setup
26_ network connection and setup
If not using a Broadband Router
For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.
4. In the <Port> pane, provide necessary information.
•HTTP Port : Used to access the camera using the Internet
browser, defaulted to 80.
•VNP Port : Used to control the video signal transfer,
defaulted to 4520.
5. Enter the password.
Enter the password of “admin” account, which was used to
access the camera.
J
`For the security purposes, you are recommended to use a combination of numbers, alphabets uppercase and lowercase and
special characters for your password.
`If you want to change the password, refer to “Administrator password change” of the user setup. (page 41)
6. Click [OK].
Manual network setup will be completed.
If using a Broadband Router
•IP Address : Enter an address falling in the IP range provided
by the Broadband Router.
ex) 192.168.1.2~254, 192.168.0.2~254,
192.168.XXX.2~254
•Subnet Mask : The <Subnet Mask> of the Broadband Router
will be the <Subnet Mask> of the camera.
•Gateway : The <Local IP Address> of the Broadband Router
will be the <Gateway> of the camera.
M
`The settings may differ depending on the connected Broadband
Router model.
For more information, refer to the user manual of the applicable router.
`For more information about port forwarding of the broadband router, refer to “Port Range Forward (Port Mapping) Setup”.
(Page 27)
If the Broadband Router has more than one camera connected
Configure the IP related settings and the Port related settings distinctly with each other.
ex)
Category Camera #1 Camera #2
IP related settings
IP Address
Subnet Mask
Gateway
192.168.1.100
255.255.255.0
192.168.1.1
192.168.1.101
255.255.255.0
192.168.1.1
Port related settings HTTP Port
VNP Port
8080
4520
8081
4521
M
`If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar of the Internet browser
before you can access the camera.
ex) http://IP address : HTTP Port
http://192.168.1.100:8080
Auto Network Setup
Run <IP Installer_v2.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
M
`For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not support this function.
1. Select a camera in the search list.
Check the MAC address of the camera on the camera’s label.
Both the [Auto Set] and [Manual Set] buttons will be
activated.
2. Click [Auto Set].
The Auto Setting dialog appears.
The <IP Address>, <Subnet Mask>, and <Gateway> will
be set automatically.
3. Enter the password.
Enter the password of “admin” account, which was used to
access the camera.
J
`For the security purposes, you are recommended to use a
combination of numbers, alphabets uppercase and lowercase and
special characters for your password.
`If you want to change the password, refer to “Administrator
password change” of the user setup. (page 41)
4. Click [OK].
Auto network setup will be completed.
English _27
●●NETWORK CONNECTION AND SETUP
DYNAMIC IP SETUP
Dynamic IP Environment Setup
•Example of the Dynamic IP environment
- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server
- If connecting the camera directly to modem using the DHCP protocols
- If IPs are assigned by the internal DHCP server via the LAN
Checking the Dynamic IP
1. Run the IP Installer on the user’s local computer.
Cameras allocated with <Dynamic IP> address are shown in
the list.
2. Select a camera from the search result.
3. Click the [Manual Set] button and check the camera’s
<Dynamic IP> address.
If you uncheck <DHCP>, you can change IP to <Static>.
PORT RANGE FORWARD (PORT MAPPING) SETUP
If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the
Broadband Router so that a remote PC can access the camera in it.
Manual Port Range Forwarding
1. From the Setup menu of the Broadband Router, select
<Applications & Gaming> - <Port Range Forward>.
For setting the port range forward for a third-party Broadband
Router, refer to the user guide of that Broadband Router.
2. Select <TCP> and <UDP Port> for each connected camera
to the Broadband Router.
The number of each port to be configured to the IP router
should be set according to the port number designated
in <Setup> - <Basic> - <IP & Port> on the camera web
viewer.
3. When done, click [Save Settings].
Your settings will be saved.
M
`Above sample instructions are based on the CISCO’s Broadband Router.
`The settings may differ depending on the connected Broadband Router model.
For more information, refer to the user manual of the applicable router.
Setting up Port Range Forward for several network cameras
•You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page.
•A user can change each port using the camera setting screen.
When Camera1 and Camera2 are connected to a router :
M
`Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function.
After connecting the network camera, set <Quick connect> of <Samsung DDNS> to <On> in the “Setup Network
DDNS” menu.
User Internet
Broadband Router
Start End Protocol IP Address
3000 3000 TCP/UDP 192.168.1.100
3001 3001 TCP/UDP 192.168.1.101
4520 4520 TCP/UDP 192.168.1.100
4521 4521 TCP/UDP 192.168.1.101
8080 8080 TCP/UDP 192.168.1.100
8081 8081 TCP/UDP 192.168.1.101
Camera1 (192.168.1.100)
HTTP port 8080
Device port 4520
RTSP port 3000
Camera2 (192.168.1.101)
HTTP port 8081
Device port 4521
RTSP port 3001
network connection and setup
28_ network connection and setup
CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC
1. Run the IP Installer.
It will scan for connected cameras and display them as a list.
2. Double-click a camera to access.
The Internet browser starts and connects to the camera.
M
`Access to the camera can also be gained by typing the camera’s IP
address in the address bar of the Internet browser.
CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE
INTERNET
Since using the IP Installer on a remote computer that is not in the Broadband Router’s network cluster is not
allowed, users can access cameras within a Broadband Router’s network by using the camera’s DDNS URL.
1. Before you can access a camera in the Broadband Router network, you should have set the port range
forward for the Broadband Router.
2. From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the
IP address of the Broadband Router in the address bar.
ex) http://www.samsungipolis.com/Product ID
M
`For registering the DDNS settings, refer to “Registering with DDNS”. (page 48)
English _29
●●WEB VIEWER
web viewer
CONNECTING TO THE CAMERA
Normally, you would
1. Launch the Internet browser.
2. Type the IP address of the camera in the address bar.
ex) • IP address (IPv4) : 192.168.1.100
http://192.168.1.100
- the Login dialog should appear.
• IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111
http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login
dialog should appear.
If the HTTP port is other than 80
1. Launch the Internet browser.
2. Type the IP address and HTTP port number of the camera in the address bar.
ex) IP address : 192.168.1.100:HTTP Port number(8080)
http://192.168.1.100:8080 - the Login dialog should appear.
Using URL
1. Launch the Internet browser.
2. Type the DDNS URL of the camera in the address bar.
ex) URL address : http://www.samsungipolis.com/Product ID
- the Login dialog should appear.
J
`Network connection is disabled in the LAN only environment.
Connecting via UPnP
1. Run the client or operating system in support of the UPnP protocol.
2. Click the camera name for search.
In the Windows operating system, click the camera name searched from the network menu.
- The login window is displayed.
Connecting via Bonjour
1. Run the client or operating system in support of the Bonjour protocol.
2. Click the camera name for search.
In the Mac operating system, click the camera name searched from the Bonjour tab of Safari.
- The login window is displayed.
To check the DDNS address
If the camera is connected directly to the DHCP cable modem, DSL modem, or PPPoE modem, the IP
address of your network will be changed each time you try to connect to the ISP (Internet Service Provider)
server.
If this is the case, you will not be informed of the IP address changed by DDNS.
Once you register a dynamic IP-based device with the DDNS server, you can easily check the changed IP
when you try to access the device.
To register your device to the <DDNS> server, visit www.samsungipolis.com and register your device first,
and then set the Web Viewer’s <Network> - <DDNS> to <Samsung DDNS>, as well as providing <Product
ID> that had been used for DDNS registration.
web viewer
30_ web viewer
PASSWORD SETTING
When you access the product for the first time, you must register the
login password.
When the “Password change” window appears, enter the new
password.
J
`For a new password with 8 to 9 digits, you must use at least 3 of
the following: uppercase/lowercase letters, numbers and special
characters. For a password with 10 to 15 digits, you must use at
least 2 types of those mentioned.
-Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/
`For higher security, you are not recommended to repeat the same characters or consecutive keyboard inputs for your
passwords.
`If you lost your password, you can press the [RESET] button to initialize the product. So, don’t lose your password by using a
memo pad or memorizing it.
LOGIN
Whenever you access the camera, the login window appears.
Enter the User ID and password to access the camera.
1. Enter “admin” in the <User name> input box.
The administrator ID, “admin”, is fixed and can not be
changed.
2. Enter the password in the <Password> input field.
3. Click [OK].
If you have logged in successfully, you will the Live Viewer
screen.
J
`When you access the camera web viewer, pay special attention to the
security by checking whether the image data is encrypted.
M
`If you check the “Remember my credentials” option when your input is done, in future you will be logged in automatically
without being prompted to enter the login information.
`You will experience the best video quality if the screen size is 100%. Reducing the ratio may cut the image on the borders.
PLUG-IN SUPPORT SPECIFICATIONS FOR EACH BROWSER
The existing plug-in web viewer and a new plug-in free web view is embedded together.
Therefore, it is possible to use the web viewer even in the latest browser environment that does not support plug-
ins such as Chrome and EDGE.
According to the browser environment, the following differences may be observed.
•Chrome, EDGE browser : Although they don’t support plug-ins, you can use a web viewer as a plug-in
free web viewer is embedded.
J
`Since the plug-in free webviewer has lower performance than the plug-in webviewer, it has a limit on the monitoring of high
quality profiles. In addition, the plug-in free webviewer does not support the audio function.
To monitor high quality profiles and play saved videos, use either a plug-in webviewer or SmartViewer.
-Plug-in free profile : A profile of H.264 20 FPS HD(1280x720) resolution, which is optimal for the plug-in free webviewer.
-Plug-in free profile generation conditions: A plug-in free profile is generated when the selected profile is FHD 20fps or higher
(H.264)/FHD 10pfs or higher (H.265) or 4M 1fps or higher (MJPEG).
-Plug-in free playback conditions: A recorded video with an HD resolution or lower
`In the following cases, the detection performance may be impaired or an malfunction may occur.
-Monotonous monitoring environment, night or low illumination environment
-Severe camera wobbling and sudden changes in illumination
•IE, Firefox, or Safari browser : You can use a web viewer even if you don’t install the existing plug-in web
viewer.
J
`To monitor/play saved video seamlessly, you are required to install a plug-in.
`In the following cases, the detection performance may be impaired or an malfunction may occur.
-Monotonous monitoring environment, night or low illumination environment
-Severe camera wobbling and sudden changes in illumination
English _31
●●WEB VIEWER
INSTALLING WebViewer PLUGIN
To access to the plug-in webviewer and play a live video (H.264/H.265) or a recorded video, an installation
message will be prompted. At this time you need to install the webviewer plug-in to use the function properly.
1. When the monitoring page is accessed for the very first time, the installation page is displayed. Click [Click
Here] to begin installation.
J
`If the plug-in installation file download status is suspended at 99% in the Internet Explorer browser, retry it after selecting
“Release SmartScreen filter” in “Tool SmartScreen filter”.
2. Click [Run] in the message window.
3. Click [Yes] when the notice window saying that all browser windows will be closed.
M
`Steps 4 and 5 will be skipped if no Web Viewer Plug-in is installed.
4. When the old version of the Web Viewer Plug-in is installed, a notice window saying the old version will be
deleted is displayed.
Click [Yes] when the notice window is displayed.
5. Click [OK].
The old version of Web Viewer Plug-in is deleted.
6. Click [Install] to begin installation of the Web Viewer Plug-in.
7. Click [Finish].
Web Viewer Plug-in installation is completed.
J
`In your internet explorer, if you need to move to the installation screen after installing the webviewer plugin, check whether
webviewer_activexplugin_lib.control in the “Tool Additional Function Management” menu is “Activated”. If not, and if there
is a persisting problem, then select “Tools Internet Options General” and delete all the search records.
USING A PLUG-IN FREE WEBVIEWER
If you access the camera from Google Chrome or MS Edge web browser, you can check and control the camera
image in real time without installing separate plug-in(s).
1. Enter your username and password to log in.
2. When you are logged in, a camera live view screen appears.
USING THE LIVE SCREEN (PLUG-IN FREE WEBVIEWER)
Item Description
a
Setup Move to the Setup screen.
b
Camera Model Name Displays the model name of the camera accessed.
c
Viewer Screen Displays the Live video on the screen.
`You can use the mouse wheel to activate the digital zooming in Viewer screen.
d
Switch View Mode
FIt ( ) A view mode in which the size of the camera video automatically fits
to the web browser size.
Original Size ( ) View mode in which the video is played in the actual resolution.
Aspect Ratio ( ) View mode that adjusts the aspect ratio to best fit the resolution.
Full Screen Double click on the video screen, and the current video will be
played in the full screen of the monitor.
e
Playback
Move to the screen where you can search for the video recording saved in your Micro SD memory
card or NAS.
`To search a recorded video, go to the play screen, place the mouse over the video and double
click.
f g he
a b c d
web viewer
32_ web viewer
Item Description
f
Profile type
You can select a profile type in <Video profile> under the <Basic> setup menu.
`Click the icon to display the name of the current profile.
J
`
Afterimages can be displayed on the screen under the following conditions if the video is
played in the monitoring page:
-The resolution is changed due to a profile change.
-Incoming data is being slowed due to a network delay when the profile is changed.
-The web browser window size and location is changed.
g
Capture Saves the snapshot as an image file in the png format.
h
Alarm output Activate the Alarm Out port.
To capture the snapshot
1. Click [Capture ( )] on the scene to capture.
2. When a captured video is saved, a notification message appears.
The captured image is saved in the designated folder for each browser.
To fit the full screen
1. Place the mouse over the video and double click.
2. This will fit the Viewer to the full screen.
3. To exit the full screen mode, press [Esc] on the keyboard.
USING THE LIVE SCREEN (PLUG-IN WEBVIEWER)
Item Description
a
Monitoring Move to the monitoring screen.
b
Playback Move to the screen where you can search for the video recording saved in your Micro SD memory
card or NAS.
c
Setup Move to the Setup screen.
d
Profile access information You can read the profile information.
e
Viewer Screen Displays the Live video on the screen.
`You can use the mouse wheel to activate the digital zooming in Viewer screen.
f
Webviewer plug-in
installation You can install webviewer plug-ins to play a live video or a recorded video.
g
Profile type
You can select a profile type in <Video profile> under the <Basic> setup menu.
`When the Web Viewer is connected, the profile information currently using is displayed.
JAfterimages can be displayed on the screen under the following conditions if the video is
played in the monitoring page:
-The resolution is changed due to a profile change.
-Incoming data is being slowed due to a network delay when the profile is changed.
-The web browser window size and location is changed.
j
a b c d fe
g
h
i
k
l
m
n
o
p
English _33
●●WEB VIEWER
Item Description
h
Screen Optimization The video size of the camera will switch to as big as the Web browser.
i
Fix the resolution Regardless of the resolution setup configured in the camera, it sets the resolution to 640x480.
Press it again to switch back to the default resolution.
j
Full Screen Switch the current video to the maximum size of the monitor.
k
Capture Saves the snapshot as an image file in the .jpg format.
l
Manual recording The user can save the video on the PC.
m
Adjust Audio Activates the audio and adjusts the audio volume.
n
Alarm output Activate the Alarm Out port.
o
Pixel Counter Checks the number of pixels in the selected area on the video screen.
p
Hide the context menu The left-corner context menu will disappear but only the menu icon.
To capture the snapshot
1. Click [Capture ( )] on the scene to capture.
2. When a captured video is saved, a notification message appears.
The captured image is saved in the designated folder for each browser.
M
`If the screen is not captured by IE browser in Windows 7 or higher, run the IE Browser with the Admin privilege.
How to record videos manually
1. Press [Manual recording ( )].
2. To end the recording, press [Manual recording ( )] again.
M
`You can save the recorded file on the PC in an avi file format. Designate a path and save the video.
To fit the full screen
1. Click the [Full Screen ( )] button.
2. This will fit the Viewer to the full screen.
3. To exit the full screen mode, press [Esc] on the keyboard.
To Use Audio
1. Click [Audio ( )] icon to activate audio communication.
2. Use [ ] bar to control the volume.
M
`If there is no sound from pulling in and out the audio jack while it is in operation, click the [Audio ( )] icon to enable it
again.
To count the number of pixels
1. Click the [On ( )] icon to activate it.
2. Drag the mouse on the video to select an area.
3. The number of pixels in the selected area is displayed on the screen.
web viewer
34_ web viewer
PLAYING THE RECORDED VIDEO (PLUG-IN FREE WEBVIEWER)
M
`Before you can play the video, you must configure the record settings. For details on record settings, refer to “Storage”. (page 52)
`To search a date-specific recorded video, move to the play screen, place the mouse over the video and double click.
Name of event search screen and its function
Item Description
a
Search event setting Set the event type to search within the search period.
b
Time Bar Move the time bar to play the video at a desired time.
c
Move Menu You can toggle between the Live and Play Recorded Video menu.
d
Play Plays/Pauses the video.
e
Full Screen Double click on the video screen, and the current video will be played in the full screen of
the monitor.
a b c e
d
To play the content after searching by event
1. On the live screen, click the [Show ( )] button.
2. If there is a video recorded on the date of search, the
applicable video is displayed on the time bar.
3. To perform event-specific search, click the [All] button at the
bottom of the time bar to select an event type.
4. Click the [OK] button.
Event searched is displayed on the time bar.
5. Click the [Play ( )] button.
6. To pause the video, click the [Pause ( )] button.
Name of time search screen and its function
Item Description
a
Setup Move to the Setup screen.
b
Video Information Displays the time information of the video played.
c
Play Speed Controls the play speed.
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00
2016/04/21 19:22:51
a b c d e f
h
i
j k
All Tampering detection 19:22:51 ~ 19:23:22 Defocus detection 19:22:57 ~ 19:23:04 Defocus detection 19:23:13 ~ 19:23:20
g
English _35
●●WEB VIEWER
Item Description
d
Capture Saves the video currently played as an image file in a jpg format.
e
Search Date Settings Sets a desired time and date on the calendar.
`The data on which a video is saved is circled under the date.
f
Switch View Mode Switches the size of image displayed on the screen.
g
Play Plays/Pauses the video.
h
Move Playback Interval Click the (/) button to move 1 frame forward/backward.
i
Time Bar Move the [Time Bar ( )] to play the video at a desired time.
j
Search Event Settings Set the type of event to search in the search field.
k
Search Event Displays the type and time of an event searched.
To play after searching by time
1. On the live screen, click the [Show ( )] button.
2. Place the mouse over the video and double click.
The screen changes to full screen.
3. Click the [Search ( )] icon.
4. On the calendar, set the search date, start time and end time.
The event searched is displayed on the time bar.
5. To perform an event-specific search, click the [All] button at
the bottom of the time bar to select an event type.
6. Click the [Play ( )] button.
The video at the selected time will be played.
7. When a video is played, the recording time of the video
currently being played is displayed.
8. Search the video forward and backward and adjust the
playback speed.
- How to Move Playback Interval
Select the
(/
) button to move 1 frame forward/
backward.
- How to Control Playback Speed
When you click the 1x, 2x, 4x, or 8x button, the playback
speed increases accordingly.
When you click the -1x, -2x, -4x, or -8x button, the
playback speed decreases -1x, -2x, -4x or -8x and the
rewind speed increases.
9. Move the position of the [Time Bar ( )] to play the video at
a desired time.
00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00
2016/04/21 19:22:51
All Tampering detection 19:22:51 ~ 19:23:22 Defocus detection 19:22:57 ~ 19:23:04 Defocus detection 19:23:13 ~ 19:23:20
web viewer
36_ web viewer
PLAYING THE RECORDED VIDEO (PLUG-IN WEBVIEWER)
M
`Before you can play the video, you must configure the record settings. For details on record settings, refer to “Storage”. (page 52)
Name of event search screen and its function
Item Description
a
Search range setting Set the search date and time range for data saved in your Micro SD memory card or NAS.
b
Search event setting Set the event type to search within the search period.
c
Event search Run the event search.
c
b
a
To play the content after searching by event
1. Click the [Playback ( )] button.
2. Specify the start time and end time of your search.
3. Select an event type for your search within the specified
period.
4. Click the [Event search] button.
The search results will be displayed in the list.
M
`If more than 800 events are recorded within the search period,
your search will be limited up to the date when the 800th event is
recorded.
For instance, if the search period is between 10th and 15th day of the month, and more than 800 events were recorded 10th
through 11th, your search will be limited up to 11th day with a total of 800 events, and events after then (from 12th) will not
be found.
5. Select a data item to play in the search list.
6. Click the [Play ( )] button.
7. To stop playing the video, click [Stop ( )].
8. To return to the search screen, click [Exit ( )].
English _37
●●WEB VIEWER
Name of time search screen and its function
Item Description
a
Time bar The section in the specific period is played by moving the time bar.
b
Search date setting
Set the search date using the calendar.
`If there is data saved in your Micro SD memory card or NAS on the day, it is marked as a
box on the calendar.
c
Audio To listen to a voice signal (if present) in the recorded video, then activate the voice signal
icon when you play it.
d
Screen optimization The camera image is converted to fit the Web browser window.
e
Fix the resolution Regardless of the resolution setup configured in the camera, it sets the resolution to
800x600. Press it again to switch back to the default resolution.
f
Capture The current image is saved as a .jpg image file.
g
Full screen The current image is converted to cover the maximum size of the monitor.
h
Video information Time data of the replayed video is displayed on the screen.
i
Backup
Set the desired date to make a backup copy of video data saved in your Micro SD memory
card or NAS.
`You can set up to 5 minutes for the backup of a saved video.
To play after searching by time
1. Click [Time Search ( )].
2. Click a desired date in the calendar.
The video on the specified date will be played.
3. If the video playback is stopped, select a time and click
[Play ( )].
The video on the selected time will be played.
4. While the video is being played, the recording time for the
current video will be shown.
5. Search for the video forward or backward, and control the
play speed.
- How to Control the Play Interval
:
Select this button to move 1 frame forward.
: Select this button to move 1 second back.
- To control the play speed
If selecting ), the button will switch to x1, x2, x4, x8, and the play speed will increase accordingly.
When you select the ( button, the playback speed decreases -1x, -2x, -4x or -8x and the rewind
speed increases.
- To control the playback direction
If you see the ) button with the play speed displayed, the video will be played forward; Whereas, if
you see the ( button with the play speed displayed, the video will be played backward.
- How to set the time bar
If you press the button, the details of the time bar section can be viewed.
If you press the button, you can view a wider range of times and the desired time can be selected
more easily.
6. Move [Time bar ( )] to a desired time point of the video before playing it.
The time containing a normal recoding file will be highlighted in blue; the time with the event recording will
be highlighted in red.
To back up the searched video
1. During playback, click [ ] on the scene to back up.
The scheduling window for backup start and end time
appears.
2. Click [ ] button.
The Save As window appears.
3. Confirm the save path and click [Save] button.
The screenshot will be backed up to the specified path.
f
b
h
i
c
d
e
g
a
web viewer
38_ web viewer
To play the backup video
The backed up images are saved in an .avi format. Gom Player, VLC Player, and Window Media Player are
recommended as the media player compatible with this format.
M
`In case of Windows Media Player, download the latest codec from www.windows7codecs.com and install it prior to use.
To Play an AVI File
(1) Micro SD memory card
1. Separate the Micro SD memory card from the camera.
J
`Before separating the Micro SD memory card, set the <Device> to <Off> in the “Setup Event Storage” menu.
2. Insert the Micro SD memory card into the PC.
3. Play the AVI file in the “\ch00\img\YYYY_mm_DD\AVI”
directory, using a media player.
M
`A filename starts with the format “001_YYYYMMDD_HHMMSS.avi”
and the file number is incremented by one.
YYYYMMDD_HHMMSS indicates the start time of data saving.
`“001_YYYYMMDD_HHMMSS.smi” file is a caption file, and you can
view it if it exists in the same directory as its related AVI file.
`The max recording time per AVI file is 5 minutes.
`Once corrupted, the data in the Micro SD memory card cannot be
replayed in the Web Viewer’s [Playback].
(2) NAS (Network-Attached Storage)
1. In Windows browser, use \\<ip address>\ to access.
ex)\\192.168.20.31\defaultfolder\ch01\img\2013_07_02\AVI
2. Go to <Computer> <Network drive connection>
Enter 1.
3. Connected to the NAS.
The directory structure is same as the directory structure for a
Micro SD memory card.
M
`A filename starts with the format “001_YYYYMMDD_HHMMSS.avi”
and the file number is incremented by one.
YYYYMMDD_HHMMSS indicates the start time of data saving.
`“001_YYYYMMDD_HHMMSS.smi” file is a caption file, and you can
view it if it exists in the same directory as its related AVI file.
`The max recording time per AVI file is 30 minutes.
`If you change or damage the saved data on your own, it will not play back or save properly.
English _39
●●SETUP SCREEN
setup screen
SETUP
On the network, you can set up basic information on the camera, video and audio, network events and system.
1. On the live screen, click the [Menu ( )] button.
2. On the menu list, click the [Setup ( )] tab.
3. The Setup screen appears.
BASIC SETUP
Video profile
1. From the Setup menu, select the <Basic ( )> tab.
2. Click <Video profile>.
3. Set the <Video profile connection policy>.
•Keep connection when profile setting is changed : Output
uses the same settings even when the settings of the
active profile are changed.
If not selected, changing a profile used by an existing
connection resets such connection.
4. Select each profile properties.
For more details, refer to “To Add/Change the Video
Profile”. (Page 40)
5. Click the input box of each item and enter / select a desired
value.
`The context menu may differ depending on the selected codec type.
•Default profile : If no profile is selected when using the Web Viewer, the default video profile is applied.
•E-mail/FTP profile : Video profile to be transferred to the specified email or FTP site.
`Only the MJPEG codec can be set as the E-mail/FTP profile.
•Record profile : This is the profile that is applied to video recording.
6. Select whether or not to input audio in the video.
Select the <Audio-In> check box and you can input audio in the video.
7. According to your situation, set ATC (Auto Transmit Control) mode.
•ATC mode : It adjusts the video properties according to the
variance in the network bandwidth, controlling the bit rate.
Adjusting the bit rate depends on the ATC mode.
- Control framerate : Reduce the frame rate if the network
bandwidth drops down.
- Control compression : Control the compression rate if the network bandwidth drops down.
Compression adjustment can cause deterioration of the image quality.
- Event(MD) : Activated when the motion detection (MD) event is set. Frame rate is adjusted when an
event occurs.
If no motion is detected in the surrounding area, the minimum amount of frames is output to save the
bandwidth use.
`If <Bitrate control> is set to <CBR>, the encoding priority according to the ATC mode will be fixed as below:
Bitrate control / ATC mode Control framerate Control compression Event(MD)
CBR Compression Framerate Framerate
•ATC sensitivity : Affect the transfer rate according to the variance in the network bandwidth.
The transfer rate will be adjusted to the fastest if the bandwidth is <Very high>, and adjusted to the
latest if the bandwidth is <Very low>.
•ATC limit : If the quality or frame rate is adjusted, the property will be changed to the applied value (%)
against the previous setting value (100%).
Note that if you reduce the property value too much, you may encounter flickering on the screen. So it
is advisable to adjust the value within the threshold.
J
`It is recommended to apply ATC control only for cameras supporting ATC.
`Set the ATC sensitivity to <Very low> in a network environment with high variance in the network bandwidth.
`If the network connection is unstable, you may encounter flickering on the screen.
8. When done, click [Apply ( )].
setup screen
40_ setup screen
To Add/Change the Video Profile
The profile setup can be added or modified to accommodate various profiles depending on the recording
conditions.
1. In <Video profile>, click the <Add> button.
2. Provide the name and select a codec.
3. Specify the conditions under which the codec will be applied.
4. Specify the details of the selected codec including resolution and frame rate.
Click the <Show> button to display detailed items.
•Resolution : Set the video size of the H.264/H.265 and MJPEG files.
•Framerate : Set the max number of video frames per sec.
•Maximum bitrate : Set the max bit rate of video when the bit rate control is set to VBR.
J
`As the bit rate can be adjusted limitedly according to the resolution, frame rate and screen complexity, the actual bit rate
can be greater than the maximum bit rate. So you must consider the use conditions when setting the value.
•Target bitrate : Set the target bit rate when the bit rate control is set to CBR.
•Bitrate control : You can select one from constant bit rate and variable bit rate for compression. Fixed
bitrate means that the network transmission bitrate is fixed while varying the video quality or frame rate,
variable bitrate means that a higher priority is placed on the video quality while varying the bitrate.
J
`After setting the fixed bit rate for bit control, if you select the video quality priority mode, depending on the complexity of
the screen, the actual transmitted frame rate may differ from the frame rate setup in order to guarantee the optimal video
quality for the given bit rate.
•Encoding priority : You can set the priority of video transmission to frame rate or compression.
•GOV length : It specifies the distance (in terms of number of frames) between two consecutive I-Frames
in a video sequence when H.264/H.265 codec was selected. (One I-Frame + 0~Several P-Frames)
•Profile : You can select the H.264/H.265 profiling method.
•Entropy coding : Reduce the possible compression loss due to encoding.
•Dynamic GOV : When the bit rate control is VBR in H.264/H.265 codec, it makes the GOV length
automatically change to the set value of the maximum dynamic GOV.
•Multicast(SVNP) : Specify the use of the SVNP protocol.
- IP address : Enter an IPv4 address with which you can connect to the IPv4 network.
- Port : Specify the video communication port.
- TTL : Set the TTL for the SVNP packet.
•Multicast(RTSP) : Specify the use of the RTSP protocol.
- IP address : Enter an IPv4 address with which you can connect to the IPv4 network.
- Port : Specify the video communication port.
- TTL : You can set the TTL for the RTP packet.
J
`If you set the Multicast address to 224.0.0.0~224.0.0.255, multicast may not work properly in all environments. In that
case, we recommend you change the multicast address.
What is GOV length?
GOV(Group of Video object planes) is a set of video frames for H.264/H.265 compression, indicating a
collection of frames from the initial I-Frame (key frame) to the next I-Frame. GOV consists of 2 kinds of
frames: I-Frame and P-Frame.
I-Frame is the basic frame for the compression, also known as Key Frame, which contains one complete
image data. P-Frame contains only the data that has changed from the preceding I-Frame.
For H.264/H.265 codec, you can determine the GOV length.
If you set a recording profile with H.264/H.265 codec, the GOV length will be framerate/2.
What is dynamic GOV?
Dynamic GOV is a function that enables the GOV to automatically change in a range from the set value of the
minimum GOV length to the maximum dynamic GOV set value according to the situation of the video.
In a video with almost no motion, GOV operates with the dynamic GOV settings, which makes the bit rate of
the entire video reduced. The I-frame is output right after a motion is detected and GOV operates with the
GOV length settings until the motion disappears.
If you use this function, the GOV of a video operates with the minimum GOV length settings.
English _41
●●SETUP SCREEN
User
1. From the Setup menu, select the <Basic ( )> tab.
2. Click <User>.
3. Provide the necessary user information.
•Administrator password change : Change the password
for the administrator.
J
`For the security purposes, you are recommended to use a
combination of numbers, alphabets uppercase and lowercase
and special characters for your password.
`It is recommended to change your password once every three
months.
`The password length and limits are shown as follows.
-A combination of at least three types of upper case, lower
case, numeric, and special characters: 8 to 9 characters.
-A combination of at least two types of upper case, lower case,
numeric, and special characters: 10 to 15 characters.
-Should be different from the ID.
-Cannot repeat the same letter, number of special characters more than 4 times.
-Don’t use 4 or more characters consecutive together. (examples : 1234, abcd)
-Don’t use 4 or more characters repeated. (examples : !!!!, 1111, aaaa)
-Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/
-After the factory setting, the admin and user passwords are initialized. You need to reset the password.
-When you access the camera web page for the first time or access it after the initialization, you will be moved to the
admin password setting menu.
-In this menu, you need to login again with the new password before using the camera web page menus.
-If the existing password is not matched, when you change the admin password, you cannot change the password.
-After changing your password, if there is a camera connected to a CMS or NVR client, then you need to re-register it
with the newly changed password. If the camera is still connected with the same password, then the account may be
locked because a client uses the previous password.
`If you try to login with the registered account, 5 or more consecutive password authentication has failed, and then the
account may be locked for thirty seconds.
`When the password is changed while multiple connections are active from a PC, the browser may malfunction. In that
case, reconnect to the server.
•Guest setup : If you select <Enable guest access>, the guest account can access the Web viewer
screen but can only view the live Viewer screen.
`The ID/password for the guest account is <guest/guest>, which cannot be changed.
•Authentication setup : If you select <Enable RTSP connection without authentication>, you can
access RTSP without logging in and view the video.
•Current users : If you select <Use>, you can set or change the user permissions.
`The manager can set up audio input and alarm output.
`Audio input/Alarm output : You can enable/disable Audio input/Alarm output in the live mode on the current user account.
`Profile : If you select <Default>, you can only see the default profile video; if selecting <All>, you can see the full profile
videos.
J
`ONVIF functions available to a registered user allowed to use ONVIF functions are limited to those of granted with permission.
4. When done, click [Apply ( )].
Date & Time
1. From the Setup menu, select the <Basic ( )> tab.
2. Click <Date & Time>.
3. Specify the time and date that will be applied to the camera.
•Current system time : Displays the current time settings of
your system.
•Timezone : Specify the local time zone based on the GMT.
•Use daylight saving time : If checked, the time will be set
one hour before the local time zone for the specified time
period.
This option will be displayed only in areas where DST is
applied.
•System time setup : Specify the time and date that will be
applied to your system.
- Manual : Sets the current time of the camera manually.
When you select the <Synchronize with PC viewer> check box, the time of the webviewer is set to
the time displayed on the PC that runs the webviewer.
- Synchronize with NTP server : Sync with the time of the specified server address.
4. When done, click [Apply ( )].
J
`If you select the <Synchronize with PC viewer>, the standard timezone should be set the same as the current timezone in
PC.
setup screen
42_ setup screen
IP & Port
1. From the Setup menu, select the <Basic ( )> tab.
2. Click <IP & Port>.
3. Click <IP address>.
4. Set the <IPv4 setup>.
•IP type : Select an IP connection type.
- Manual : Specify the IP address, Subnet mask,
Gateway, DNS1, and DNS2.
- DHCP : Specify the DNS1 and DNS2.
- PPPoE : Specify the DNS1, DNS2, ID and Password.
`If you set it to <Manual>, you should specify the IP, Subnet mask, Gateway, DNS 1 & 2 manually.
•MAC address : Shows the MAC address.
•IP address : Displays the current IP address.
•Subnet mask : Displays the <Subnet mask> for the set IP.
•Gateway : Displays the <Gateway> for the set IP.
•DNS1/DNS2 : Displays the DNS(Domain Name Service) server address.
5. Set the <IPv6 setup>.
`Set to <Use> to use IPv6 address.
•Default : Use the default IPv6 address.
•DHCP : Display and use the IPv6 address obtained from the DHCP server.
•Manual : Enter IP address and gateway manually and use it.
J
`The IP addressing system will be defaulted to DHCP. If no DHCP server is found, the previous settings will be restored
automatically.
`Once completed with editing, click [Apply ( )] to apply changes and the browser exits. After a while, connect again
with the changed IP.
6. Click <Port>.
7. Type in each item in the Port menu as necessary.
`Neither the port range between 0 and 1023 nor port 3702 is available.
•HTTP : HTTP port used to access the camera via the web
browser.
The default is 80(TCP).
`Setting the HTTP port for Safari and Google Chrome browsers to 65535 is not allowed by security policy.
•HTTPS : In this version, the security of the web communication protocol HTTP is strengthened. It can
be used when you set HTTPS mode in SSL.
The initial value is set to 443(TCP).
`The available setting range is 1024~65535. (For security reasons, in your Safari or Google Chrome browser, you may not use
65535 as your HTTPS port.)
•RTSP : Used to transfer videos in the RTSP mode; the default is 554.
•Use timeout : When connecting to RTSP, this function resets the connection if there’s no response for a
certain time.
•Device port : Set a port used to transfer video signals with the Hanwha Techwin protocols.
M
`If changed the HTTP port, the browser exits.
Afterwards, address should contain the newly assigned HTTP port trailing the IP.
ex) IP address: 192.168.1.100, HTTP port : Assigned 8080 http://192.168.1.100:8080
(If HTTP port is set to 80, no need to specify the port number)
`Using RTSP and HTTPS is recommended in order to prevent the image information from being restored.
8. When done, click [Apply ( )].
Event setup
You can easily set the event detection items, and move to the detailed setting.
1. From the Setup menu, select the <Basic ( )> tab.
2. Click <Event setup>.
3. Activate desired items on the Event list.
4. When done, click [Apply ( )].
M
`To configure detailed event settings, click a desired type. You will be
redirected to the detailed settings.
English _43
●●SETUP SCREEN
AUDIO & VIDEO SETUP
Video setup
1. From the Setup menu, select the <Audio & Video ( )>
tab.
2. Click <Video setup>.
3. Select a <Video source> mode.
•Flip mode : Turn upside down the image that is captured
by the camera.
•Mirror mode : Flip horizontal the image that is captured by
the camera.
•Hallway view : Rotates the video captured by the camera
according to the set angle.
You can rotate the video 0, 90 or 270 degrees.
`If you change settings, the browser window will be closed and the camera restarted. Please access again later.
4. Specify the privacy zone.
5. When done, click [Apply ( )].
To set the privacy zone
You can specify a certain area of the camera video to be protected for your privacy.
1. Set it to <On>.
2. Click [Apply ( )].
3. Drag the mouse over the video to select an area.
4. Enter the name and select the color, and then click [OK].
5. If you want to delete a name in the list, select it and click
[Delete ( )].
Audio setup (QND-6010R/6020R/6030R)
You can set the input value of the audio connected to the camera.
1. From the Setup menu, select the <Audio & Video ( )>
tab.
2. Click <Audio setup>.
3. Set the audio input value.
•Source : Sets the audio input.
- Internal microphone : Built-in microphone embedded in
the camera.
•Codec : Specify the audio codec.
- G.711 : A audio codec standard, it uses 64 Kbps PCM (Pulse Code Modulation) encoding.
ITU standard audio codec that is adequate for digital voice transfer in PSTN network or through a PBX.
- G.726 : ITU standard audio codec applying ADPCM (Adaptive Differential Pulse Code Modulation) for
variable bit rates of 40/32/24/16 Kbps to 64 Kbps PCM encoding.
•Bitrate : Set the bit rate to differentiate compression ratio if using G.726 codec.
•Gain : Specify the audio input amplification.
J
`Sound quality deterioration or howling may occur if the loudness of the sound source or gain value were set excessively.
4. When done, click [Apply ( )].
Audio setup (QNO-6020R/6030R, QNV-6010R/6020R/6030R)
You can set the input value of the audio connected to the camera.
1. From the Setup menu, select the <Audio & Video ( )>
tab.
2. Click <Audio setup>.
3. Set the audio input value.
•Source : Sets the audio input.
- Line : Connect the cable to the audio device.
- External microphone : Uses an external microphone.
•Apply power to Ext. Mic. : Select this check box when the external microphone is not powered, and the
power will be supplied from the camera to the microphone. You can configure settings when selecting
<External microphone>.
•Codec : Specify the audio codec.
- G.711 : A audio codec standard, it uses 64 Kbps PCM (Pulse Code Modulation) encoding.
ITU standard audio codec that is adequate for digital voice transfer in PSTN network or through a
PBX.
- G.726 : ITU standard audio codec applying ADPCM (Adaptive Differential Pulse Code Modulation) for
variable bit rates of 40/32/24/16 Kbps to 64 Kbps PCM encoding.
•Bitrate : Set the bit rate to differentiate compression ratio if using G.726 codec.
•Gain : Specify the audio input amplification.
J
`Sound quality deterioration or howling may occur if the loudness of the sound source or gain value were set excessively.
4. When done, click [Apply ( )].
setup screen
44_ setup screen
Camera setup
You can change the camera settings according to the environment where the camera is located.
1. From the Setup menu, select the <Audio & Video ( )>
tab.
2. Click <Camera setup>.
3.
Configure the settings as necessary of :
Image preset,
Sensor,
SSDR, White balance, Back light, Exposure, Day/Night,
Special, OSD, IR
4. When done, click [Apply ( )].
`
If a certain time (timeout: 240s) is elapsed
with your not pressing the [Apply
( )]
button after changing the settings, your changes will not be
applied.
If you want to set an image preset
Users can set presets easily.
The selected image preset mode will be in operation during the configured period, but at other times the
values configured in the user preset mode are reflected.
1. Select a desired mode from the image presets.
•Definition focus : This is the factory setting for your camera.
Select it for video recording, focusing on reproducibility.
•Motion focus : Record a moving object clearly. If there are
many moving objects, such as on a road or in a crowded
place like a museum, select this option.
J
`Noise level can increase in a low illumination environment, and
sensitivity can go down.
•Reduced noise : Select this when you need a video with
low noise in the low illumination environment.
•Bright video : This makes the dark area in a full video brighter.
J
`Video contracts effects are reduced.
•Motion focus&Reduced noise : Use this when there are many moving objects, such as on a road
or in a crowded place like a museum, or when you need a video with low noise in a low illumination
environment.
•Motion focus&Bright video : Use it when there are many moving objects, such as on a road or in a
crowded place like a museum, or when you need to make a dark area in full video brighter.
•Vivid video : Makes the entire video displayed in vivid colors.
J
`The contrast of the video reduces and the color reproducibility becomes low.
•User preset : Select it if you want to display video with settings chosen by you.
J
`When selecting a mode other than the preset mode, you can’t set the shutter speed, AGC, SSDR, SSNR and color.
2. Set the camera item for each image preset mode.
3. Set the <Activation time>.
•Off : Your camera will execute a specific image preset operation at all times.
•Only scheduled time : Your camera will execute a specific image preset operation for the time period set
by you on each date.
4. Click the [Setup ( )] button.
5. Set the <Mode> and <Time>.
6. When done, click [Apply ( )].
Initial setting for each image preset mode
Image preset Minimum
shutter
Maximum
shutter AGC SSDR SSNR COLOR
Definition focus Default (1/5) 1/12000 Default (High) Default (12) Default (12) Default (50)
Motion focus 1/30 1/12000 Default (High) Default (12) 4 Default (50)
Reduced noise 1/15 1/12000 Middle Default (12) Default (12) Default (50)
Bright video Default (1/5) 1/12000 Default (High) 18 Default (12) Default (50)
Motion focus&Reduced
noise 1/30 1/12000 Middle Default (12) 4 Default (50)
Motion focus&Bright video 1/30 1/12000 Default (High) 18 4 Default (50)
Vivid video Default (1/5) 1/12000 Default (High) 18 Default (12) 90
User preset Manual Manual Manual Manual Manual Manual
M
`The preset setup functions as an aid to users to configure setup. If you don’t want the preset function, deactivate it before
use.
`If you change the image preset, only shutter/AGC/SSDR/SSNR/COLOR are reset to the default value for each model.
`The “Camera Setting” value does not change between presets.
English _45
●●SETUP SCREEN
To Set the Sensor
It specifies how many frames the camera CMOS sensor will capture per second.
1. Select <Sensor>.
2. Select <Mode>.
M
`Refer to “Video profile” for the framerate setup range of the <Video
profile> according to mode setup. (Page 39)
To Set SSDR (Samsung Super Dynamic Range)
In a scene where the difference between bright and dark is severe, you can increase the brightness of the
dark area alone to regulate the overall brightness.
1. Select <SSDR>.
2. Set <Mode> to <On>.
3. Configure the <Level> and <D-Range> settings as
necessary.
•Level : Adjust the level of the dynamic range.
•D-Range : Select the amplitude area of the dynamic range.
To Set White Balance
You can correct the image colors based on white under any lighting conditions.
1. Select <White balance>.
2. Select <Mode>.
•ATW : Corrects the colors of the camera video
automatically.
•Manual : You can adjust the red and blue gains of the
camera video manually.
•Outdoor : Automatically corrects the video colors of the
camera to be optimized to the outdoor environment.
•Indoor : Automatically corrects the video colors of the camera to be optimized to the indoor
environment.
•AWC : Corrects the colors of the camera video to be optimized to the current lighting condition and
screen mode.
To obtain the optimal condition for the current lighting, put the focus of the camera to a white paper
and press the [Set] button. If the lighting environment is changed, you should readjust the settings
accordingly.
M
`In AWC mode, click the [Set] button if you want to keep the white balance level of the current image.
J
`The white balancing may not work properly in the following conditions:
If this is the case, switch to AWC mode.
-If the surrounding condition of the object is out of the temperature correction range
ex) Clear sky, sunset
-If the surrounding of the object is dark
-If the focus of the camera directly faces the florescent lighting or if the camera is installed in a place of variable
illumination, the white balancing operation may be unstable.
To Set BLC
You can specify a desired area on the video manually and set the area to be displayed more clearly.
1. Select <Back light>.
2. Set <Mode> to <BLC>.
3. Set <BLC level>.
You can change the level to adjust the brightness of the
monitoring area.
4. Set the <Top, Bottom, Left, Right> levels to specify the
target area.
J
`When setting BLC, a green box is displayed on the screen for 15
seconds.
`To prevent malfunction at the time of BLC setup, the vertical space of the BLC area should be over 40 and below 60 while the
horizontal space over 30 and below 60.
To Set WDR
It displays a sharp image of the objects in a scene where both bright and dark areas exist.
1. Select <Back light>.
2. Set <Mode> to <WDR>.
3. Specify the <WDR level>.
J
`It is recommended to use WDR in the indoor environment.
`Noise may exist between the dark area and the bright area in the
WDR mode.
`The maximum and minimum shutter values are initialized whenever
you turn on or off the WDR mode.
`When using WDR, the frame rate reduces by half.
Example) When using a 30fps mode and the WDR mode, a video of 15fps is output.
setup screen
46_ setup screen
To Set Exposure
You can adjust the exposure level of the camera.
1. Select <Exposure>.
2. Select each item and set it properly.
•Brightness : Adjust the screen brightness.
•Minimum shutter : The limit of the longest exposure time.
`Shutter is the mode to set up the range of the sensor exposure time
which will specify the upper and lower limits for the electronic shutter
movement.
`The framerate may be reduced in the dark condition if Shutter has a
lower value than specified in the Sensor mode.
•Maximum shutter : The limit of the shortest exposure time.
•Anti flicker : It prevents screen flickering incurring from the dissonance between the surrounding lighting
and the frequency.
•SSNR : Noise of the video is removed.
•SSNR level : Adjust the noise reduction level.
•AGC : Select AGC Control mode.
Adjust the gain value of the video (that, in particular, was recorded at a low contrast scene and had a
lower brightness level than normal) to control the video brightness.
J
`The image exposure can be saturated depending on the Shutter setup range.
To Set Day/Night
1. Select <Day/Night>.
2. Select each item and set it properly.
•Mode : Mode is used to adjust the color of Color or Black
and White.
- Color : The video is always output in color.
- B/W : The video is always output in black and white.
- Auto : Normally, it is set to Color but to B&W under low
luminance at night.
`If AGC of the <Exposure> menu is set to <Off>, the day/night
mode cannot be set to <Auto>.
- External : It controls the color of the video when the
alarm input terminal is synchronized with an external
device.
- Schedule : Set the time during which the camera is
operated in the color mode.
•Dwell Time : It specifies the period for which the selected brightness condition must be maintained to
switch the lighting mode from Day to Night or vice versa.
•Duration : It specifies the interval of lighting mode conversion.
•Alarm in : The video is set to Color or B/W as the alarm sensor is open or closed.
`If the Day/Night mode is set to External Input, the alarm input function of the Event-Alarm Input page is disabled.
•Activation time(Color) : It specifies the schedule for color mode operation.
`If it is set, the Color mode is maintained from 00 second of the starting time to 59 second of the ending time.
J
`When switching to the day/night mode, the motion detection mode does not work.
English _47
●●SETUP SCREEN
To Setup Special
1. Select <Special>.
2. Select each item and set it properly.
•Sharpness : Adjust the overall sharpness of the image.
If selecting <On>, you can adjust the sharpness of the
image.
•Sharpness level : The higher the level is, the sharper and
clearer the outline of the image becomes.
•Gamma : Adjust the contrast of the image.
•Color level : Adjust the strength of video color.
•LDC : Enables/Disables the image distortion correction.
•LDC Level : Adjusts the degree of distortion correction.
To Set OSD
1. Select <OSD>.
2. Select each item and set it properly.
•Camera title : It specifies the name of the camera to be
displayed on the screen.
Select the <Use> check box to add a camera name.
•Add : Click the <Add> button and you can add a total of 5
lines, 15 characters per line and a total of 60 characters.
•Camera title X, Y : It specifies the position of the camera
name on the screen.
•Date & time : Set the time display and date formats on the
screen.
•Date & Time X, Y : Specify the position of time display on
the screen.
•Weekday overlay : Specify the use of date display date on
the screen.
•Size : Sets the size of OSD to small/medium/large.
•Color : Sets the color of the OSD to white/red/blue/green/black/gray.
•Transparency : Sets the transparency to opaque/transparency 1/transparency 2/transparency 3.
•Overlay image : The image selected by the user can be displayed at the top left of the screen.
- Browse : Searches and selects a bitmap type file.
- Upload : Uploads a selected file.
- Remove : Deletes the selected file.
M
`The specifications of an applicable file include 16bit (RGB565 not supported) or 24bit bitmap file with a length of 128 pixel
for the width and height and a file size of 52KB or less.
J
`A position-adjustable item (Camera title, Date & Time) may not be displayed normally if it overlaps with another fixed OSD
item.
`If you change the language, the X-Y coordinates are initialized.
It is recommended to set the X-Y coordinates after setting the language.
To Set IR
1. Select <IR>.
2. Select each item and set it properly.
•Mode : When the IR indicator turns on in B/W mode, the
screen will be protected from saturation on the center area
so that you can identify a short-distant object.
- Off : IR mode will be disabled.
- Auto : Adjust the IR brightness according to the brightness of the object on the center screen.
WiseStream
Function to detect the complexity of the video in an environment in which no major motion is generated and
adjust the video quality to lower the output bit rate.
Returns the video quality to the original settings when a motion is generated to prevent video information
loss.
1. From the Setup menu, select the <Audio & Video ( )>
tab.
2. Click <WiseStream>.
3. Select an intensity of the Wise Stream.
- Off : Wise Stream function will be disabled.
- Low : Reduces the image quality of the video slightly.
When the bit rate is OFF, the image quality will be reduced
up to 15%.
- Medium : Reduces the image quality of the video to the medium level. When the bit rate is OFF, the
image quality will be reduced up to 30%.
- High : Reduces the image quality of the video considerably. When the bit rate is OFF, the image quality
will be reduced up to 50%.
4. When done, click [Apply ( )].
J
`In the following cases, the WiseStream function may malfunction.
-Sudden screen switch may cause distortion of the video.
-It is not appropriate to use in an environment with too much movement and motion on the screen.
setup screen
48_ setup screen
NETWORK SETUP
DDNS
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of a camera into a
general Host Name so that the user can easily remember it.
J
`You can use the DDNS service only if the internet is connected.
1. From the Setup menu, select the <Network ( )> tab.
2. Click <DDNS>.
3. Select the <DDNS> connection type.
4. Type in the DDNS items according to the selected type.
•Samsung DDNS : Select this if you use the DDNS server
provided by Hanwha Techwin.
- Product ID : Enter the product ID that is registered with
the Samsung DDNS service.
- Quick connect : It sets port forwarding automatically when used with a UPnP (Universal Plug and
Play) supporting router.
M
`If you want to use the DDNS service without using a hub that supports the UPnP function, click Quick connect, then
go to the hub menu and activate port forwarding for your hub.
For more on how to set port forwarding for your hub, refer to “Port Range Forward (Port Mapping) Setup”. (page
27)
•Public DDNS : Select one of provided public DDNS servers when you use a public DDNS server.
- Service : Select desired public DDNS service server.
- Host name : Enter the name of the host that is registered with the DDNS server.
- User name : Enter the user name for the DDNS service.
- Password : Enter the password for the DDNS service.
5. When done, click [Apply ( )].
J
`If selected <Quick connect>, be sure to select Samsung DDNS service.
Registering with DDNS
To register your product with the Samsung DDNS
1. Visit the iPOLiS web site (www.samsungipolis.com) and sign
in with a registered account.
2. From the top menu bar, select <DDNS SERVICE> - <MY
DDNS>.
3. Click [PRODUCT REGISTRATION].
4. Enter the product ID.
`You must perform the duplicate check for the ID that you entered.
5. Select a <CLASSIFICATION> and specify the <MODEL
NUMBER>.
6. Specify the product location with a description if necessary.
7. Click [REGISTRATION].
The product will be added to the product list that you can
check.
English _49
●●SETUP SCREEN
M
`If selected <Allow> for IP Filtering and <IPv6 setup> of <IP & Port> is set to <Use>, both IPv4 and IPv6 addresses of the
computer currently configuring should be assigned.
`The IP address of the computer used for the current setup cannot be added to <Deny>, it should be added to <Allow>.
`Only the IP addresses that are set to <Use> will be displayed in the filter column.
6. Select an IP to delete from the list.
Click the [Delete ( )] button.
7. When done, click [Apply ( )].
HTTPS
You can select a secure connection system or install the public certificate for this purpose.
1. From the Setup menu, select the <Network ( )> tab.
2. Click <HTTPS>.
3. Select a secure connection system.
`To access the camera using HTTPS mode, you have to type the IP
address for the camera in the form of “https://<Camera_IP>”.
If you failed to configure the Web viewer settings in HTTPS mode with
Internet Explorer, edit the Internet options as follows: <Menu Tools
Internet Options Advanced Security Uncheck TLS 1.0, and check
TLS 1.1, TLS 1.2>
4. Search for the public certificate that you want to install on the camera.
To install the certificate on the camera, you need to provide a certificate name (it can be arbitrarily assigned
by the user), certificate file issued from the certification authority and a key file.
`The <HTTPS (Secure connection mode using the public certificate)> item will be active only if there exists a public certificate
installed.
5. When done, click [Apply ( )].
Installing the certificate
1.
Enter the certificate name.
2.
Click the [
Browse ( )
] button, select the public certificate file and key file to be installed, and then
click the [
Install ( )
] button.
Deleting the certificate
1. Click [Delete ( )] button.
2. To delete a public certificate, you should access the network video decoder in the mode of <HTTP (Do
not use secure connection)> or <HTTPS (Secure connection mode using a unique certificate)>.
To connect to the Samsung DDNS in camera setup
1. From the DDNS setup page, set <DDNS> to <Samsung
DDNS>.
2. Provide the <Product ID> that you registered product ID with
the DDNS site.
3. Click [Apply ( )].
When the connection is successfully made, you will see the
message of <(Success)> on the screen.
Configuring public DDNS in Camera Settings
1. Open the DDNS settings page and select <Public DDNS> for <DDNS>.
2. Enter the corresponding site’s host name, user name and password.
3. Click [Apply ( )] button.
If the connection properly establishes, <(Success)> appears.
4. When done, click [Apply ( )].
M
`To use DDNS service properly, both DDNS setup and the router’s port forwarding setup are required.
For port forwarding setup, refer to “Port Range Forward (Port Mapping) Setup”. (page 27)
IP filtering
You can create a list of IPs that you want to grant or deny access to them.
1. From the Setup menu, select the <Network ( )> tab.
2. Click <IP filtering>.
3. Select <Filtering type>.
•Deny : If selecting this, access from those IPs that are
added to the filtering will be restricted.
•Allow : If selecting this, access from only those IPs that are
added to the filtering will be accepted.
4. Click the [Add ( )] button.
The IP list will be created.
5. Provide the IP that you want to grant or deny access from.
When you enter an IP address and a Prefix, the list of IP addresses available will appear in the right-side
filter range column.
setup screen
50_ setup screen
802.1x
When connecting network, you can choose whether using 802.1x protocol, and then install the certification.
1. From the Setup menu, select the <Network ( )> tab.
2. Click <802.1x>.
3. Set the <IEEE 802.1x setting>.
•IEEE 802.1x : Specify the use of the 802.1x protocol.
•EAP type : Select EAP-TLS or LEAP.
•EAPOL version : Select version 1 or 2.
•ID : Enter the client certificate ID in EAP-TLS and the user
ID in LEAP.
•Password : Enter the client private key password in EAP-
TLS and the user password in LEAP. You do not have to
enter the password in EAP-TLS if it uses a key file that is not encrypted.
J
`If the connected network device does not support the 802.1x protocol, the protocol will not operate properly even if you set it.
`LEAP is an authentication method with poor security. Use it only in an environment where EAP-TLS is not available.
4. Install/remove the certificate.
The certificate is needed only for EAP-TLS.
•CA certificates : Select a public certificate that contains the public key.
•Client certificate : Select a public certificate that contains the client certificate key.
•Client private Key : Select a public certificate that contains the client private key.
5. When done, click [Apply ( )].
To install/remove 802.1x related certificates
1. Press the [Browse ( )] button for each item and select a certificate to install.
2. If no certificate is installed, you will see “Not Available” appearing next to the selected item.
3. Press the [Install ( )] button to start installation with a message of “Installed” next to the item.
4. Press the [Delete ( )] button to remove the certificate.
QoS
You can specify the priority to secure a stable transfer rate for a specific IP.
1. From the Setup menu, select the <Network ( )> tab.
2. Click <QoS>.
3. Click the [Add ( )] button.
The IP list will be created.
4. Enter an IP address to which you will apply QoS.
M
`The default prefix for IPv4 is 32;
For DSCP, the default is set to 63.
`Only the IP addresses that are set to <Use> can be prioritized.
5. Select an IP to delete from the list.
Click the [Delete ( )] button.
6. When done, click [Apply ( )].
SNMP
With the SNMP protocols, the system or network admin can monitor the network devices on a remote site,
and configure the environment settings.
1. From the Setup menu, select the <Network ( )> tab.
2. Click <SNMP>.
3. Specify the <SNMP>.
•Enable SNMP v1 : SNMP version 1 will be active.
•Enable SNMP v2c : SNMP version 2 will be active.
- Read community : Provide the name of the read
community where you can access to the SNMP
information.
The default name is <public>.
- Write community : Provide the name of the write
community where you can access to the SNMP information. The default name is <write>.
•Enable SNMP v3 : SNMP version 3 will be active.
- Password : Specify the default password for SNMP version 3.
`The default password can be exposed to a hacking thread so it is recommended to change the password after installing the
product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
`Password should be longer than 8 characters, no more than 16 characters.
English _51
●●SETUP SCREEN
EVENT SETUP
FTP / E-mail
You can configure the FTP/E-mail server settings so that you can transfer the images taken with camera to
your PC if an event occurs.
1. From the Setup menu, select the <Event ( )> tab.
2. Click <FTP / E-mail>.
3. Select <FTP configuration> or <E-mail configuration> and
enter / select a desired value.
•FTP configuration
- Server address : Enter the IP address of the FTP server
that you transfer the alarm or event images to.
- ID : Enter the user ID with which you will log in to the
FTP server.
- Password : Enter the user account password for logging
into the FTP server.
- Upload directory : Specify the FTP path where you will
transfer the alarm or event images.
- Port : The default port of the FTP server is 21; however, you can use a different port number
according to the FTP server settings.
- Passive mode : Select <On> if you need to connect in passive mode due to the firewall or the FTP
server settings.
•E-mail configuration
- Server address : Enter the SMTP address of the email server that you transfer the alarm or event
images to.
- Use authentication : Select whether to use authorization.
- Use TLS : Specify the use of TLS.
- ID : Enter the user ID for logging into the email server.
- Password : Enter the user account password for logging into the email server.
- Port : The default port of the email server is 25; however, you can use a different port number
according to the email server settings.
- Recipient : Enter the address of the email recipient.
- Sender : Enter the address of the email sender. If the sender address is incorrect, the email from the
sender may be classified as SPAM by the email server and thus may not be sent.
- Subject : Enter a subject for your email.
- Body : Provide the text for the massage. Attach the alarm or event images to the email that you are
preparing.
4. When done, click [Apply ( )].
•Enable SNMP Trap : SNMP trap is used to send important events and conditions to the Admin.
- Community : Enter the trap community name to receive messages.
- IP address : Enter the IP address to which messages will be sent.
- Authentication failure : It specifies whether an event shall be generated when the community
information is invalid.
- Network connection : It specifies whether an event shall be generated when the network
disconnection is restored.
4. When done, click [Apply ( )].
J
`SNMP v3 is only able to be set when the secure connection mode is HTTPS.
Refer to “HTTPS”. (page 49)
`If you don’t use SNMP v3, there may be a security issue.
Auto IP configure
You can set the IP available for access and camera searching automatically.
1. From the Setup menu, select the <Network ( )> tab.
2. Click <Auto IP configure>.
3. Set the <Link-Local IPv4 address>.
An additional IP address may be assigned to assess the
camera from the Link-Local network.
•Auto configure : It specifies Able or Disable for the Link-
Local IPv4 address.
•IP address : Display the assigned IP address.
•Subnet mask : Display the subnet mask of the assigned IP.
4. Set the <UPnP discovery>.
Cameras can be automatically searched in the client and operating system in support of the UPnP
protocol.
•UPnP discovery : It specifies Able or Disable for UPnP Discovery.
•Friendly name : Display the camera name.
Friendly name is displayed in the format of WISENET-<Model Name>-<MAC Address>.
M
`In the Windows operating system which basically supports UPnP, the cameras connected to the network are displayed.
5. Set the <Bonjour>.
Cameras can be automatically searched in the client and operating system in support of the Bonjour
protocol.
•Bonjour : It specifies Able or Disable for Bonjour.
•Friendly name : Display the camera name.
Friendly name is displayed in the format of WISENET-<Model Name>-<MAC Address>.
M
`In the Mac operating system, which support Bonjour by default, the connected cameras are automatically displayed in the
Bonjour bookmark of the Safari web browser.
If the Bonjour bookmark is not displayed, check Bookmarks Setup in the “Preference” menu.
6. When done, click [Apply ( )].
setup screen
52_ setup screen
Storage
You can activate recording on your device, set the recording conditions, check the saved data capacity and
format the device itself.
1. From the Setup menu, select the <Event ( )> tab.
2. Click <Storage>.
3. Select a device to save data in.
M
`If your device is properly recording data, it will display “Recording”.
`If you see an “Error” message, check the following:
-Check the storage to see if it is connected to the device.
-Check the files in the storage to see if they are damaged.
-Check the storage to see if they are physically damaged.
`If the “Error” message does not disappear after following the
instructions, format the Micro SD card.
After formatting, if the error message still remains, replace the Micro
SD card.
`If you remove the Micro SD card without changing a button to ‘off’
position in settings or if you connect a camera to an unstable power
source, the Micro SD card may be damaged.
J
`After operation in record mode, you are limited to 2 simultaneously accessible profiles, and to 3 connected users. However,
existing users will be sustained.
To make recording on the Micro SD memory
1. Set the SD card unit to <On>.
2. Click the [Apply ( )] button.
3. Check the memory card’s <Free size> and <Total size>.
You can format the Micro SD card by clicking the <Format> button.
`Some frames may be skipped if the Micro SD memory card operates at the lower speed than recommended.
For more details, refer to “Recommended Micro SD/SDHC/SDXC Memory Card Specifications”. (Page 6)
`For a Micro SD memory card with a large capacity, the formatting will be slowed down accordingly.
`The data traffic will increase when the camera is set to higher resolution, higher bit rate, and/or higher framerate.
If there is too much data traffic, some frame may be skipped although it is stored in a full frame.
`When a frame skip occurs, images are saved at the rate of min. one image per sec.
4. Specify the storage action.
•Record profile : The name of profile to be recorded is displayed.
•Normal : Make recording at a certain frame rate.
•Event : Set the recording type for a certain event that occurs.
•Pre event duration : Specify the time point before the occurrence of the alarm; starting from the time
point, the images will be transferred. You can specify up to 5 seconds before the occurrence of the
alarm.
•Post event duration : Specify the time point after the occurrence of the alarm; to the specified time
point, the images will be transferred. You can specify up to 120 seconds after the occurrence of the
alarm.
•Record file type : It specifies the file format of the recorded images.
- STW : It is Hanwha Techwin’s unique file format.
- AVI : It is the conventional avi format.
J
`If the Record file type is changed, the existing data is formatted.
•Overwrite : If the Micro SD memory is full, this will delete old data and store new data in replacement.
•Auto delete : Data for a certain period is deleted, while other data is not deleted.
This can be set within the range of one day to 180 days.
J
`If the storage period is expired, data is automatically deleted and new data will be recorded. Once deleted, it cannot be
recovered.
5. Set <SD File System>.
•Type : Camera supports VFAT and ext4 as an SD card file system, which can be configured by the user.
(However, in case of ext4 file system, an additional application is required to recognize the Windows
operating system)
J
`If the settings are changed, the existing data will be formatted.
`It may take up to 10 minutes to format an SD card in the ext4 file system.
6. Specify the <Normal record setup>.
•Always : Always save recorded video in the Micro SD memory card.
`If set to Always, the activation time cannot be changed.
•Only scheduled time :
Records only on the specified time of the specified day of week.
•[Clear ( )] : Reset all settings.
7. When done, click [Apply ( )].
English _53
●●SETUP SCREEN
NAS (Network Attached Storage) guide
J
`Since data may not be saved after a temporary network interruption when using NAS, it is recommended that you use SD at
the same time to prevent loss of recorded images.
`If the setting allows a Micro SD memory card and the NAS to be simultaneously connected for use, the higher priority for
recording goes to the NAS.
`If you activate Overwrite to the NAS by setting it to <Off> and the available capacity is below 1%, it will be saved in the Micro
SD card.
`If you are saving data in the NAS, you might be unable to save it when you insert a Micro SD memory card used by another
camera.
`NAS recommended specs : Refer to “NAS recommended specs”. (Page
6
)
`If you change the NAS saving while saving data in the NAS, it will not be reflected in the system immediately.
`If you remove NAS equipment on your own while saving data, or if the network is disconnected, NAS saving operation will be
terminated abnormally.
`NAS saving allows only one camera to a folder. Logging in with another camera is not allowed, and the images will not be
saved.
The following is a description of how to save data using the NAS according to the Synology NAS method,
which is one of the recommended products.
1. Access the Synology NAS as an admin.
In this example, the NAS IP Address is set to
[192.168.20.253].
2. If you access it as an admin, the following screen will be
displayed. Click the [Control Panel].
3. Click the <Shared Folder> in the file sharing and privilege
menu.
If you want to record in your NAS
1. Set the saving operation and basic recording.
J
`Auto deletion is supported only if your NAS meets the recommended
specifications.
2. Enter the information registered in your NAS.
•IP address : Unique IP address assigned to the NAS.
•ID : An ID registered in the NAS.
•Password : Password registered in the NAS.
•Default folder : Designate the NAS user folder to save data
in.
3. Click the [Test] button to see if you can successfully connect
to the NAS.
J
`If the success message is displayed, it means that you can
successfully save data in the NAS.
`If the fail message is displayed, check the following.
-Confirm that the IP address of the NAS is valid.
-Confirm that the ID/password of the NAS is valid.
-Confirm that you can access the folder designated as the default folder using the ID of the NAS.
-Confirm that the NAS SMB/CIFS items are unchecked.
-Confirm that the NAS IP address and the camera IP address are in the same format.
ex) The NAS & camera subnet mask initial value is 255.255.255.0.
If the IP address is 192.168.20.32 then the NAS IP address should be in the range of 192.168.20.1~192.168.20.255.
-Check whether you tried to access as another user without formatting the default folder saved or used.
-Confirm that you used recommended NAS equipment.
4. After the settings are completed, set the NAS unit to <On>.
5. Click the [Apply ( )] button.
6. Log in the NAS and check the <Free size> and <Total size>.
You can format the default folder specified in the NAS connection setting by clicking the <Format> button.
`Since data may not be saved after a temporary network interruption when using NAS, it is recommended that you use SD at the
same time to prevent loss of recorded images.
`The data traffic will increase when the camera is set to higher resolution, higher bit rate, and/or higher framerate.
If there is too much data traffic, some frame may be skipped although it is stored in a full frame.
`When a frame skip occurs, images are saved at the rate of min. one image per sec.
setup screen
54_ setup screen
4. Click the [Create] button.
5. After entering the shared folder name(ID), click the [OK]
button to create a shared folder.
In this example, the shared folder name is [testDirectory].
6. In Windows, for NAS access, set the privilege for the shared
folder as follows.
Check the admin’s [Read/Write].
7. Click on the <User> in the file sharing and privilege menu.
8. After clicking the [Create] button, enter name(ID) and
password.
In this example, name(ID) is set to [testID] and password is
also set to [testID].
J
`According to the NAS recommendations, when you use Netgear’s
NAS equipment, do not allocate the capacity for use.
9. In Windows, set the privilege for NAS access.
For the shared folder created in step 4 called “testDirectory”
check [Read/Write].
10. Basic setting in the NAS is completed.
Connect your camera to the actual NAS.
As shown below, enter the NAS connection setting items.
11. After entering item 10, check <On>.
12. Click the [Apply ( )] button.
Finish saving by using the NAS.
Alarm output
1. From the Setup menu, select the <Event ( )> tab.
2. Click <Alarm output>.
3. Configure the camera alarm output settings.
`If you change the alarm output type, the alarm out button on the
monitoring page and alarm output type displayed on Event Setup page
will be changed accordingly.
•Type
- Normal open : Considers “Open circuit” status of the
sensor or alarm input device as normal, and triggers alarm event if becomes “Closed circuit” status.
- Normal close : Considers “Closed circuit” status of the sensor or alarm input device as normal, and
triggers alarm event if becomes “Open circuit” status.
•Mode : Sets the alarm output method.
`There is difference between operations when clicked alarm output button while disabled.
- Pulse : It is activated during the time period specified by the duration (switching interval) and then
becomes inactive automatically.
- Active/Inactive : It maintains as activated until the user clicks the button again to make it inactive.
•Duration : Set the alarm duration that maintains activated if the mode is set to pulse, from 1 to 15
seconds.
4. When done, click [Apply ( )].
English _55
●●SETUP SCREEN
Time schedule
You can configure settings to transmit images at regular intervals at a scheduled operation time regardless of
the occurrence of an event.
1. From the Setup menu, select the <Event ( )> tab.
2. Click <Time schedule>.
3. Set whether or not to <Enable>.
4. Specify the <Transfer interval>.
5. Specify the <Activation time>.
•Always : Always activates in operated mode at the set
interval.
•Only scheduled time : Periodically activates in operated
mode at a specified time and date.
J
`The transfer interval setting value must be smaller than the preset
activation interval to succeed in image transmission.
6. Specify the activation conditions.
•FTP : Specify the use of the FTP transfer if an event occurs.
`Refer to “FTP / E-mail” for more details. (page 51)
7. When done, click [Apply ( )].
Alarm input
You can set the alarm input type, activation time, and operation mode.
1. From the Setup menu, select the <Event ( )> tab.
2. Click <Alarm input>.
3. Set whether or not to <Enable>.
4. Select the type.
•Normal open : It is normally open, but if it is closed, an
alarm will be triggered.
•Normal close : It is normally closed, but if it is open, an
alarm will be triggered.
5. Specify the <Activation time>.
•Always : Always check if an alarm occurs. It activates in
operated mode when the alarm occurs.
`If set to <Always>, the activation time cannot be changed.
•Only scheduled time : Check if an alarm occurs at a specified day of the week for a specified time
period. It activates in operated mode when the alarm occurs.
•[Clear ( )] : Reset all settings.
•Minute : Click an area in Activation Time and set the time
by minutes.
•Hour : Drag your mouse at Activation Time and set the
time by hours.
6. Specify an operation that will perform if an alarm occurs.
•FTP : Specify the use of FTP transfer in the alarm input
setup.
`Refer to “FTP / E-mail” for more details. (page 51)
•E-mail : Specify the use of email transfer in the alarm input
setup.
`Refer to “FTP / E-mail” for more details. (page 51)
•Record : You can set up the alarm to record to a Micro SD
card or an NAS when operating.
`Set <Device> to <On> in <Storage>. (page 52)
•Alarm output1 : Select whether to set the alarm output if an alarm is incoming, and specify the alarm
output time.
7. When done, click [Apply ( )].
setup screen
56_ setup screen
Tampering detection
You can set to detect tampering attempts and trigger events, such as sudden change of camera’s framing
direction, blocked lens and other overall change of scenes from the video.
1. From the Setup menu, select the <Event ( )> tab.
2. Click <Tampering detection>.
3. Set whether or not to <Enable>.
4. Set the tampering detection sensitivity. The higher the
sensitivity, detects the minutest tampering attempts.
5. Specify the activation time and activation condition.
`For more information about <Activation time> and <Action>, refer to
“Alarm input”. (page 55)
6. When done, click [Apply ( )].
J
`The default tampering detection function may not work properly in
the following cases:
-Under circumstances of simple background or low illumination and night time may lower the detection sensitivity.
-A severe shaking of the camera or a drastic change to the illumination can be considered a tampering by mistake.
-Detection of the tampering may take some time (maximum 5 seconds) right after the tampering was made.
-Once a tampering is detected, the camera will resume a normal operating after a certain stability time (approx. 5 seconds)
during which no detection will be performed.
`If false alarms are generated frequently, decrease the sensitivity gradually to minimize false alarms.
If you choose a lower sensitivity, only a sudden tempering is detected.
`If you use a higher sensitivity, alarms may be generated even from very small changes, but false detection in response to
changes in an object or brightness may occur.
Defocus detection
You can configure settings to generate an alarm signal when a defocus of the camera lens is detected.
1. From the Setup menu, select the <Event ( )> tab.
2. Click <Defocus detection>.
3. Set whether or not to <Enable>.
4. Set the sensitivity.
The higher the sensitivity value is, the finer defocus can be
detected.
5. Specify the activation time and activation condition.
`For more information about <Activation time> and <Action>, refer to
“Alarm input”. (page 55)
6. When done, click [Apply ( )].
J
`It may take a certain length of time (up to 5 seconds) to detect the defocus after a defocus situation occurs.
`In the following cases, the defocus detection performance may be impaired or a malfunction may occur.
-Monotonous monitoring environment, night or low illumination environment
-Sudden changes in the illumination (e.g. indoor light shutting off)
-Lens blocked by a large object that covers almost all of the screen
-Changes the focus object by changing the camera position.
Motion detection
You can configure settings to generate an event signal when a motion detection event is generated.
1. From the Setup menu, select the <Event ( )> tab.
2. Click <Motion detection>.
3. Enable the motion detection mode.
4. Set <Sensitivity>, <Size> and <Area>.
5. Specify the activation time and activation condition.
`For more information about <Activation time> and <Action>, refer to
“Alarm input”. (page 55)
6. When done, click [Apply ( )].
English _57
●●SETUP SCREEN
J
`Before using, set the minimum and maximum motion sizes to suit desired motion range to be detected.
`Detected size of an object may have difference with the actual size according to its shape.
`Up to 16 objects from the top side of the screen can be displayed.
`In the following cases, motion detection performance may be impaired or a malfunction may occur.
-The object color or brightness is similar to the background.
-Small activities around the border area of the camera’s field of view.
-Multiple movements continue occurring at random due to a scene change, rapid lighting changes or other reasons.
-A fixed object continues moving in the same position.
-Motions of less position changing such as approaching to the camera or fading away from the camera.
-Moving object approaches to the camera too close
-An object hides other objects behind.
-Two or more objects overlap or one object divides in multiple portions.
-Too fast object (for a proper detection, one object should be found overlapping between contiguous frames).
-
Reflection / blur / shadow due to a strong light such as direct sunlight, illumination, or headlamp.
-In severe snow, rain, wind or in dawn / dusk.
To use Motion detection
It detects a motion that meets all conditions specified by sensitivity, size and area.
1. Select a motion detection mode.
2. Select <Sensitivity> tab to set the sensitivity level. You can
set the sensor’s sensitivity to detect a motion out of the
background from the monitoring video.
J
`In a situation that definitely distinguishes objects out of backgrounds,
set this to a low sensitivity level. For opposite case that is hard to
distinguish objects like low illuminated situation, set this to a high
level.
3. Select <Size> tab.
You can limit the minimum/maximum size of motion to be
detected.
•Minimum size (pixel) : To set the minimum size of detected
motions, select <Minimum size (pixel)> and then point
and drag to the desired size on the screen using the
mouse.
•Maximum size (pixel) : To set the maximum size of
detected motions, select <Maximum size (pixel)> and
then point and drag to the desired size on the screen with
your mouse.
J
`Motions smaller than the specified minimum size or bigger than the maximum size are not detected. To avoid unintended
detections caused by great and small noises, set minimum/maximum motion sizes appropriately in accordance to your
environments.
Note that same motions on the same location can be differently detected in their detection size; it is recommended to
consider and include the tolerable difference when setting the minimum/maximum detection sizes.
4. Select <Area> tab.
You can specify an area on the screen to include or exclude
the area to/from detection.
You can specify up to 4 areas.
•Detection area : Sets the entire screen as excluded from
detection, and adds specified area as motion detection
area. Select 4 vertices in the image with your mouse to
specify the detection area.
•Non detection area : Sets the entire screen as motion
detection area, and excludes specified area as not to be
detected. Select 4 vertices in the image with your mouse
to specify the non-detection area.
5. To delete a designated area, right click the mouse on the
video and click the [Delete] button displayed on the popup
window.
6. When done, click [Apply ( )].
Network disconnection
When the network is physically disconnected, it is considered as an event to be saved.
1. From the Setup menu, select the <Event ( )> tab.
2. Click <Network disconnection>.
3.
Set whether or not to
<
Enable
>
.
4. Specify the activation time and activation condition.
`For more information about <Activation time> and <Action>, refer to
“Alarm input”. (page 55)
5. When done, click [Apply ( )].
setup screen
58_ setup screen
SYSTEM SETUP
Product information
1. From the Setup menu, select the <System ( )> tab.
2. Click <Product information>.
3. Check the camera information, or provide details according
to your network environment.
•Model : Model name of the product.
•Serial number : Product serial number.
•Device name : Provide a device name that will be displayed on the Live screen.
•Location : Specify the location where the camera is installed.
•Description : Provide detailed information about the camera location.
•Memo : Provide an explanation about the camera for better understanding.
•Language : Select a preferred language for the Web Viewer OSD.
M
`The default language is set to <English>.
4. When done, click [Apply ( )].
Upgrade / Reboot
1. From the Setup menu, select the <System ( )> tab.
2. Click <Upgrade / Reboot>.
3. Select a desired item and set it appropriately.
•Upgrade : Performs upgrading the system.
•Factory default : Initializes all setting information including
the camera settings to the factory reset state. (however,
logs are not initialized)
- Exclude Setting : If you select the <Network> check box,
network settings are not initialized.
`The IP addressing system will be defaulted to DHCP if you reset the camera. If no DHCP server is found, the previous settings
will be restored automatically.
•Configuration backup & Restore : Backs up the current system settings before performing the
restoration process. The system is automatically restarts after backup or restoration.
•Restart : Restarts the system.
To perform the upgrade
1. Click [Browse] and specify a file to upgrade.
2. Click [Upgrade].
3. An “Upgrade” progress bar is prompted to show the upgrading status.
4. Once completed upgrading, the browser exits and the camera restarts.
M
`It may take a max of 10 minutes for the upgrade process.
If you forcibly terminate the upgrade process, upgrade will not be completed properly.
`During restarting the system, accessing with web viewer will not be made.
`You can download the latest version from the Hanwha Techwin web site.
To back up the current settings
1. Click [Backup].
2. A file in a “.bin” file format is saved in “Library” -> “Document” -> “ Downloads”.
To restore the backup settings
1. To restore the backup settings, click [Restore].
2. Select a desired backup file.
M
`If you perform the backup or restoration, the web browser will be closed and the camera will reboots.
`If you try to recover the config file backed up in other model, some functions may malfunction and you need to change the
setting manually.
English _59
●●SETUP SCREEN
Log
You can check the system log or event log.
1. From the Setup menu, select the <System ( )> tab.
2. Click <Log>.
3. Select a log type.
•Access Log : You can check the log information that
contains the user’s access and the access time.
•System log : You can check the system logs where
any system changes are recorded including the time
information.
•Event log : You can check the event logs including the time
information.
4. From the right log list, select an item to search for.
•If you select <All> in the top left dropdown list, all logs for the applicable log type will be displayed.
5. If one page can not display all the logs available, use the bottom buttons to move to the previous, next, or
the last item.
6. Click on the <Backup> button to save all the log data for the currently selected mode in the “time stamp
value create by camera in modelname-mode-camera.txt file” in the download folder for the browser.
M
`Each page displays 15 logs with the latest one displayed at the top.
`Each log contains up to 1,000 records and after 1,000 records are saved, the oldest log is deleted when a new record is
generated.
Status
You can check the profile information.
1. From the Setup menu, select the <System ( )> tab.
2. Click <Status>.
3. The profile information screen is displayed.
•Profile access : Show the information of the newly added
profile.
- Profile : Show the information of the newly added
codec.
- Bitrate(kbps) : Show both the actual bit rate and the set bit rate.
- Framerate(fps) : Show both the actual frame rate and the set frame rate.
- ATC(%) : Show the ATC status.
- Concurrent users count : Show the number of concurrent users who access the profile.
•Current users : Shows information on users accessing web viewer and displaying monitoring video.
- Profile : Show the name of the profile accessed by the user.
- Bitrate(kbps) : Show the current bit rate.
- Network connection status : It shows whether the network is working fine.
- IP : Show the IP address of the current user.
M
`To check information on the profile currently used, click [Update] again to refresh it.
It takes a certain time for any changes to be applied.
`You can check the profile access status by clicking the [Menu ( )] - [Status ( )] tab.
60_ appendix
appendix
SPECIFICATION
Items Description
QND-6010R/6020R/6030R QNO-6020R/6030R QNV-6010R/6020R/6030R
Video
Imaging Device 1/2.9” 2.19M CMOS
Total Pixels 2,000(H) x 1,121(V)
Effective Pixels 1,984(H) x 1,105(V)
Scanning System Progressive
Min. Illumination Color : 0.15 Lux, B/W : 0 Lux
Lens
Focal Length (Zoom Ratio)
QND-6010R/QNV-6010R : Fixed 2.8mm
QND-6020R/QNO-6020R/QNV-6020R : Fixed 3.6mm
QND-6030R/QNO-6030R/QNV-6030R : Fixed 6mm
Max. Aperture Ratio F1.8
Angular Field of View
QND-6010R/QNV-6010R : D:125˚ / H:110˚ / V:61˚
QND-6020R/QNO-6020R/QNV-6020R : D:102.44˚ / H:86.48˚ / V:46.22˚
QND-6030R/QNO-6030R/QNV-6030R : D:61.14˚ / H:52.54˚ / V:28.86˚
Min. Object Distance -
Lens Type Fixed
Mount Type Board type
Pan / Tilt /Rotate
Pan Range 0° ~ +350° - 0° ~ +350°
Tilt Range 0° ~ +67° - 0° ~ +67°
Rotate Range 0° ~ +355° - 0° ~ +355°
Operational
Viewable Length 20m
QNV-6010R : 20m
QNO-6020R/QNV-6020R : 25m
QNO-6030R/QNV-6030R : 30m
Camera Title
Off / On (Displayed up to 20 characters per line)
- W/W : English/Numeric/Special Characters
- Common : Multi-line (Max 5), Color (Grey/Green/Red/Blue/Black/White),
Transparency, Auto Scale by Resolution
Day & Night True Day & Night
Backlight Compensation Off / BLC / WDR
Items Description
QND-6010R/6020R/6030R QNO-6020R/6030R QNV-6010R/6020R/6030R
Operational
Wide Dynamic Range 120dB
Digital Noise Reduction SSNR (Off / On)
Motion Detection Off / On (4ea polygoon zones)
Privacy Masking Off / On (6ea rectangler zones)
Gain Control Off / Low / Middle / High
White Balance ATW / AWC / Manual / Indoor / Outdoor
LDC (Lens distortion control) On/Off (5 levels with Min/Max)
Electronic Shutter Speed Minimum / Maximum / Anti flicker
Flip / Mirror Flip / Mirror / Hallway view
Intelligent Video Analytics Motion detection with metadata, tempering, defocus detection
Alarm I/O Input 1ea / Output 1ea
Alarm Triggers Motion detection, Tampering Detection, SD card error, NAS error, Alarm input,
Defocus detection
Alarm events
yFile upload via FTP, E-Mail
yNotification via E-Mail
yLocal storage(SD/SDHC/SDXC) or NAS recording at Event (Alarm Triggers)
yExternal output
Pixel Counter Support (plug-in viewer only)
Network
Ethernet RJ-45 (10/100BASE-T)
Video Compression Format H.265, H.264, MJPEG
Resolution 1920x1080 / 1280x1024 / 1280x960 / 1280x720 / 1024x768 / 800x600 /
800x448 / 720x576 / 720x480 / 640x480 / 640x360 / 320x240
Max. Framerate H.265/H.264 - Max 30fps at all resolutions
MJPEG - Max 15fps
Smart Codec WiseStream
Video Quality Adjustment H.264/H.265 : Target Bitrate Level Control
MJPEG : Quality Level Control
English _61
●●APPENDIX
Items Description
QND-6010R/6020R/6030R QNO-6020R/6030R QNV-6010R/6020R/6030R
Network
Bitrate Control Method H.264/H.265 : CBR or VBR
MJPEG : VBR
Streaming Capability Multiple Streaming (Up to 3 Profiles)
Audio I/O Built-in MIC Line in
Audio Compression Format
G.711 µ-law /G.726 Selectable
G.726 (ADPCM) 8KHz, G.711 8KHz
G.726 : 16Kbps, 24Kbps, 32Kbps, 40Kbps
Audio Communication Uni-directional
IP IPv4, IPv6
Protocol
TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTCP, RTSP, NTP, HTTP, HTTPS, SSL/TLS,
DHCP, PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2), ARP, DNS, DDNS,
QoS, PIM-SM, UPnP, Bonjour
Security
HTTPS(SSL) Login Authentication
Digest Login Authentication
IP Address Filtering
User access Log
802.1x Authentication
Streaming Method Unicast / Multicast
Max. User Access 6 users at Unicast Mode
Edge Storage
Micro SD/SDHC/SDXC (up to 128GB)
- motion Images recorded in the SD/SDHC/SDXC memory card can be downloaded.
NAS(Network Attached Storage)
Manual recording at Local PC
Application Programming
Interface
ONVIF Profile S/G
SUNAPI(HTTP API)
Webpage Language English, French, German, Spanish, Italian, Chinese, Korean, Russian, Japanese,
Swedish, Portuguese, Czech, Polish, Turkish, Dutch, Hungarian, Greek
Items Description
QND-6010R/6020R/6030R QNO-6020R/6030R QNV-6010R/6020R/6030R
Network
Web Viewer
Supported OS : Windows 7 / 8.1 / 10, MAC OS X 10.9, 10.10, 10.11
Plug-in free web viewer
Supported web browsers : Google Chrome 47, MS Edge 20
Plug-in web viewer
Supported web browsers : MS Explorer 11, Mozilla Firefox 43, Apple Safari 9
※ Mac OS X only
Central Management
Software SmartViewer
Environmental
Operating Temperature /
Humidity
-10°C ~ +55°C (14°F ~
+131°F) / Less than 90%
RH
-30°C ~ +55°C (-22°F ~ +131°F) / Less than 90%
RH
* Start up should be done at above -20°C
Storage Temperature
/ Humidity -30°C ~ +60°C (-22°F ~ +140°F) / Less than 90% RH
Ingress Protection - IP66
Vandal Resistance IK08 IK10
Electrical
Input Voltage / Current PoE(IEEE802.3af, Class3), DC 12V
Power Consumption
QND-6010R : Max.
7W(PoE), Max.
5.8W(DC12V)
QND-6020R/6030R :
Max. 6.5W(PoE), Max.
5.43W(DC12V)
Max. 7W(PoE), Max.
6W(DC12V)
QNV-6010R : Max.
7W(PoE), Max.
5.8W(DC12V)
QNV-6020R/6030R :
Max. 6.8W(PoE), Max.
5.7W(DC12V)
Mechanical
Color / Material Ivory / Plastic Dark gray / Metal Ivory / Metal
Dimension (ØxH) Ø110 x H86mm Ø70.0 x H246mm Ø120.3mm x H91.7mm
Weight 290g 730g 490g
appendix
62_ appendix
PRODUCT OVERVIEW
QND-6010R/6020R/6030R
Unit : mm (inch)
QNO-6020R/6030R
Unit : mm (inch)
QNV-6010R/6020R/6030R
English _63
●●APPENDIX
PROBLEM SOLUTION
File is not transferred to the email
even if a motion detection event is
generated with <Motion detection>
set to <On> in the <Event> page.
yVerify the settings in the following sequence:
A. Check <Data & Time> settings.
B. The <Motion detection> should be set to <Enable>.
C. Check if the <E-mail> option of <Event setup> menu is checked to use.
Cannot record into the Micro SD
memory card.
yCheck if the memory card is defective.
Micro SD memory card is inserted but
the camera does not operate properly.
yCheck if the memory card is inserted in the proper direction. Operation of memory card that
is formatted by other devices is not guaranteed with this camera unit
yFormat the memory card again in <Setup> <Event> <Storage> menu.
Cannot record in the NAS.
yConfirm that the information registered in the NAS is correct.
It reports that NAS setting has failed.
yConfirm that the IP address of the NAS is valid.
yConfirm that the ID/password of the NAS is valid.
yConfirm that you can access the folder designated as the default folder using the ID of the
NAS.
yConfirm that the NAS SMB/CIFS items are unchecked.
yConfirm that the NAS IP address and the camera IP address are in the same format.
ex) The NAS & camera subnet mask initial value is 255.255.255.0.
If the IP address is 192.168.20.32 then the NAS IP address should be in the range of
192.168.20.1~192.168.20.255.
yCheck whether you tried to access as another user without formatting the default folder
saved or used.
yConfirm that you used recommended NAS equipment.
TROUBLESHOOTING
PROBLEM SOLUTION
No video is displayed when accessing
the plug-in free webviewer on Safari
via HTTPS.
yOn the authentication popup window prompted when initially accessing https, click "View
Authentication Certificate" and select the "Always trust when connecting to the designated
webviewer IP" check box.
yIf the webviewer continues failing to display a video after you select "Next" on the message
window below, press the command key + Q to exit the Safari browser, access again and
follow the procedures stated above.
I can’t access the camera from a web
browser.
yCheck to make sure that the camera’s Network settings are appropriate.
yCheck to make sure that all network cables have been connected properly.
yIf connected using DHCP, verify that the camera is able to acquire dynamic IP addresses
without any problem.
yIf the camera is connected to a Broadband Router, verify that port forwarding is properly
configured.
Viewer got disconnected during
monitoring.
yConnected Viewers become disconnected upon any change to camera or network
configurations.
yCheck all network connections.
yIf the camera is connected over an PPPoE network, it’ s possible for Viewer to disconnect
under poor network conditions.
No video is displayed when I newly
access the webviewer or connect
streaming to the client.
yThe maximum number of profiles available is 3.
The connection may be lost if you use 4 or more of profiles.
Example) If you access MJPEG, H264 and H265 and then access with a different profile, the
connection will be lost.
The camera connected to the network
is not detected in the IP installer
program.
yTurn off the firewall settings on your PC and then search the camera again.
Images overlap.
yCheck whether two or more cameras are set to a single multicast address instead of different
addresses. If a single address is used for multiple cameras, the images may overlap.
No image appears.
yIf the transmission method is set to multicast, check whether there is a router that supports
multicast in the LAN the camera is connected to.
OPEN SOURCE ANNOUNCEMENT
GPL/LGPL software license
The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding
Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@hanwha.com
If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source
distribution might be charged.
GPL SW
Component Name License URL
Base Kernel
Busybox
iproute2-4.3.0
iptables-1.4.21
ethtool-4.2
mtd-1.5.2
mii-diag-2.11
rp-pppoe-3.11
wpa_supplicant-2.5
bash-4.3.30
zeroconf
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 2.0
GPL 3.0
GPL 2.0
http://www.busybox.net/downloads/snapshots
http://ftp.netfilter.org/pub/iptables
ftp://ftp.infradead.org/pub/mtd-utils
http://www.roaringpenguin.com/pppoe/
LGPL SW
Component Name License URL
gLibc
Inetutils
neon-0.29.6
LGPL 2.0
LGPL 3.0
LGPL 2.0 http://www.webdav.org/neon/
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C)1989, 1991 Free Software Foundation, Inc. 51 Franklin Street,Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to
guarantee your freedom to share and change free software-- to make sure the software is free for all its users. This General Public License applies to most of the
Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered
by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you
wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs ; and that you know
you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate
to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have.
You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights
with two steps :
(1)copyright the software, and (2)offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author’s
protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone
else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the
original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not
licensed at all. The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin S
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this
General Public License.
The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under
copyright law : that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License ; they are outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by
running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the
absence of any warranty ; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions :
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run,you must cause it, when started running for such interactive use in the most
ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that
you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.
(Exception:if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print
an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably
considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate
works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you ; rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program
(or with a work based on the Program)on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2)in object code or executable form under the terms of Sections 1 and 2
above provided that you also do one of the following :
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on
a medium customarily used for software interchange ; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source
distribution, a complete machinereadable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange ; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial
distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code
for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for
all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However,
as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source
code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object
code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from you under this License will not have their licenses terminatedso long as such parties remain in full
compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or
its derivative works.
These actions are prohibited by law if you do not accept this License.Therefore, by modifying or distributing the Program (or any work based on the Program), you
indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)that contradict the conditions of this License, they do not excuse you from the conditions of this License.
If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you
may not distribute the Program at all.
For example, if a patent license would not permit royaltyfree redistribution of the Program by all those who receive copies directly or indirectly through you, then
the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as
a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to
contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by
public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent
application of that system ; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who
places the Program under this License may add an explicit geographical distribution limitation excluding those countries,so that distribution is permitted only
in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar
in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the
Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either
of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may
choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission.
For software which is copyrighted by the Free Software Foundation,write to the Free Software Foundation ; we sometimes make exceptions for this. Our
decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software
generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM
“ASIS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS
WITH YOU. SHOULD THE PROGRAMPROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY
WHO MAY MODIFY AND/OR REDISTRIBUTE DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way
to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty ; and each file should have at least the “copyright”
line and a pointer to where the full notice is found.one line to give the program’s name and an idea of what it does.
Copyright (C)yyyy name of author
This program is free software ; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software
Foundation ; either version 2 of the License, or (at your option)any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY ; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program ; if not, write to the Free Software Foundation, Inc.,51 Franklin
Street, Fifth Floor, Boston, MA 02110-1301, USA.
Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an
interactive mode :
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY ; for details type ‘show w’. This is free software,
and you are welcome to redistribute it under certain conditions ; type ‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may
be called something other than ‘show w’ and ‘show c’ ; they could even be mouse-clicks or menu items-- whatever suits your program.
You should also get your employer (if you work as a programmer)or your school, if any, to sign a “copyright disclaimer” for the program,if necessary. Here is a
sample ; alter the names:
Yoyodyne, Inc.,hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker. signature of
Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your
program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is Lwihcaetn ysoeu want to do,
use the GNU Lesser General Public instead of this License.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright (C) 2007 Free Software Foundation, Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works. The licenses for most software and other practical works are
designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to
share and change all versions of a program-- to make sure it remains free software for all its users.
We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work released this way by its
authors.
You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to
make sure that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you
want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities
if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others. For example, if you distribute copies of such a
program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive
or can get the source code. And you must show them these terms so they know their rights. Developers that use the GNU GPL protect your rights with two
steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it. For the developers’ and
authors’ protection, the GPL clearly explains that there is no arranty for this free software. For both users’ and authors’ sake, the GPL requires that modified
versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions. Some devices are designed to deny
users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the
aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is
precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products. If such problems arise
substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of
users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-
purpose omputers, but in those that do, we wish to avoid the special anger that patents applied to a free program could make it ffectively proprietary. To prevent
this, the GPL assures that atents cannot be used to render the program non-free. he precise terms and conditions for copying, distribution and modification
follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks. “The Program” refers to any copyrightable work
licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The
resulting work is called a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable
copyright law, except executing it on a computer or modifying a private copy.
Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer
network, with no transfer of a copy, is not conveying. An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient
and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent
that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of
user commands or options, such as a menu, a prominent item in the list meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a
particular programming language, one that is widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major
Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a
Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a major essential
component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the
work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object
code and to modify the work, including scripts to control those activities.
However, it does not include the work’s System Libraries, or generalpurpose tools or generally available free programs which are used unmodified in performing
those activities but which are not part of the work. For example, Corresponding Source includes interface definition files associated with source files for the
work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to require, such as by intimate data
communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source. The Corresponding
Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This
License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the
output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey
covered works to others for the sole purpose of having them make modifications exclusively for you, or provide you with facilities for running those works, provided
that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus making or running the covered works for
you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside
their relationship with you. Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10
makes it unnecessary.
3. Protecting Users’ Legal Rights From anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright
treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by
exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of
enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on
each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in accord with section 7 apply
to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the Program. You may charge any
price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4,
provided that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modified it, and giving a relevant date.
b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies
the requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along
with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless of how they are packaged. This License gives no
permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not
display Appropriate Legal Notices, your work need not make them do so. A compilation of a covered work with other separate and independent works,
which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of
a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of
the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the
other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding
Source under the terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source
fixed on a durable physical medium customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least
three years and valid for as long as you offer spare parts or customer support for that product model, to give anyone who possesses the object code
either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily
used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the
Corresponding Source from a network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the corresponding Source. This alternative is allowed only
occasionally and noncommercially, and only if you received the object code with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source
in the same way through the same place at no further charge. You need not require recipients to copy the Corresponding Source along with the object
code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third party)
that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source.
Regardless of what server hosts the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these
requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the
work are being offered to the general public at no charge under subsection 6d. A separable portion of the object code, whose source code is excluded
from the Corresponding Source as a System Library, need not be included in conveying the object code work. A “User Product” is either (1) a “consumer
product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or
sold for incorporation into a dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For
a particular product received by a particular user, “normally used” refers to a typical or common use of that class of product, regardless of the status of
the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product
regardless of whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of
use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified
versions of a covered work in that User Product from a modified version of its Corresponding Source. The information must suffice to ensure that the continued
functioning of the modified object code is in no case prevented or interfered with solely because modification has been made. If you convey an object code
work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession
and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding
Source conveyed under this section must be accompanied by the Installation Information. But this requirement does not apply if neither you nor any third party
retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that
has been modified or installed by the recipient, or for the User Product in which it has been modified or installed. Access to a network may be denied when
the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an
implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions
that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid under applicable law. If
additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed
by this License without regard to the additional permissions. When you convey a copy of a covered work, you may at your option remove any additional
permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases when you modify the
work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material)
supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works
containing it; or
c) Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different
from the original version; or
d) Limiting the use for publicity purposes of names of licensors or authors of the material; or
e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
f) Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual
assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose on those licensors and authors. All other
non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it,
contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term. If a license document
contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by the terms
of that license document, provided that the further restriction does not survive such relicensing or conveying. If you add terms to a covered work in
accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating
where to find the applicable terms. Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as
exceptions; the above requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and
will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright
holder explicitly and finally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior
to 60 days after the cessation. Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you ofthe violation
by some reasonable means, this is the first time you have received notice of violation of this License (for any work) from that copyright holder, and you cure the
violation prior to 30 days after your receipt of the notice. Termination of your rights under this section does not terminate the licenses of parties who have received
copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the
same material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a
consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you
permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by modifying or propagating
a covered work, you indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject
to this License. You are not responsible for enforcing compliance by third parties with this License. An “entity transaction” is a transaction transferring control
of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from
an entity transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in
interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if
the predecessor has it or can get it with reasonable efforts. You may not impose any further restrictions on the exercise of the rights granted or affirmed under
this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate
litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing
the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed
is called the contributor’s “contributor version”. A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether
already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version,
but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control”
includes the right to grant patent sublicenses in a manner consistent with the requirements of this License. Each contributor grants you a non-exclusive,
worldwide, royaltyfree patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and
propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an
express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an
agreement or commitment not to enforce a patent against the party. If you convey a covered work, knowingly relying on a patent license, and the Corresponding
Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available network server or other
readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the
patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream
recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your
recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid. If,
pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a
patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work,
then the patent license you grant is automatically extended to all recipients of the covered work and works based on it. A patent license is “discriminatory” if it
does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically
granted under this License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing
software, under which you make payment to the third party based on the extent of your activity of conveying the work, and under which the third party grants,
to any of the parties who would receive the covered work from you, a discriminatory patent license
(a)
in connection with copies of the covered work conveyedby you (or copies made from those copies), or
(b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent
license was granted, prior to 28 March 2007. Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to
infringement that may otherwise be available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from
the conditions of thisLicense. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this License and any other pertinent
obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty for further conveying
from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the
Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU
Affero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue to apply to the part which is
the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction through a network will apply to the
combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/ or new versions of the GNU General Public License from time to time. Such new versions will be similar
in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later
version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the
Free Software Foundation. If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s
public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you additional
or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO
OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply
local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of liability
accompanies a copy of the Program in return for a fee.
OpenSSL Combined License
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit.
See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please
contact openssl-core@openssl.org.
Component Name License URL
openssl-1.0.2e OpenSSL Combined License http://www.openssl.org/source
Copyright (c) 1998-2011 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed
by the OpenSSL Projectfor use in the OpenSSL Toolkit. (http://www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written
permission. For written permission, please contact openssl-core@openssl.org.
5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the
OpenSSL Project.
6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for
use in the OpenSSL Toolkit (http://www.openssl.org/)"
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young(eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved.
This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found
in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the
same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should
be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online
or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following
conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement: "This product includes cryptographic
software written by Eric Young (eay@cryptsoft.com)" The word 'cryptographic' can be left out if the rouines from the library being used are not cryptographic
related :-).
4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: "This
product includes software written by Tim Hudson (tjh@cryptsoft. com)"
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and
put under another distribution licence [including the GNU Public Licence.]
BSD License
Some software components of this product incorporate source code covered under the BSD license as follows.
Component Name License URL
net-snmp-5.7.3
pcre-8.38
libcap-1.7.4
lighttpd-1.4.35
MiniUPnP Project Client
pppd-2.4.7
BSD
BSD
BSD 2.0
BSD 2.0
BSD 2.0
BSD 2.0
http://www.net-snmp.org/about/license.html
http://www.kernel.org/pub/linux/libs/security/linux-privs/libcap2
http://www.opensource.org/licenses/bsd-license.html
http://opensource.org/licenses/BSD-3-Clause
lighttpd is a secure, fast, compliant, and very flexible webserver that has been optimized for high-performance environments. It has a very low memory footprint
compared to other webservers and takes care of cpuload. Its advanced feature-set (FastCGI, CGI, Auth, Output-Compression, URL-Rewriting and many more)
make lighttpd the perfect webserver-software for every server that suffers load problems. Simple Network Management Protocol (SNMP) is an Internetstandard
protocol for managing devices on IP networks. It is used mostly in network management systems to monitor the devices attached to the network for conditions
that need administrative attention. Net-SNMP is a suite of applications used to implement SNMP v1, SNMP v2c and SNMP v3 using both IPv4 and IPv6. For
more additional information, send email to help.cctv@hanwha.com.
Copyright (C) 2004, Kneschke, incremental
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met :
- Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
- Neither the name of the ‘incremental’ nor the names of its contributors may be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Copyright (c) 1998-2001 University College London
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met :
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed
by the Computer Science Department at University College London.
4. Neither the name of the University nor of the Department may be used to endorse or promote products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHORS AND CONTRIBUTORS ``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSEARE DISCLAIMED. IN NO EVENT
SHALL THE AUTHORS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 1988, 1989, 1990, 1991, 1993, 1994, 1995, 1996 The Regents of the University of California.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. Neither the name of the Regents of the University of California nor the names of its contributors may be used to endorse or promote products derived from
this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Copyright (c) 2006, Creative Labs Inc
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. Neither the name of the Creative Labs nor the names of its contributors may be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Copyright (c) 2005-2012, Thomas BERNARD
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. Neither the name of Thomas BERNARD nor the names of its contributors may be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Various copyrights apply to this package, listed in various separate parts below. Please make sure that you read all the parts.
Part 1: CMU/UCD copyright notice: (BSD like)
Copyright 1989, 1991, 1992 by Carnegie Mellon University Derivative Work - 1996, 1998-2000
Copyright 1996, 1998-2000 The Regents of the University of California
All Rights Reserved
Permission to use, copy, modify and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above
copyright notice appears in all copies and that both that copyright notice and this permission notice appear in supporting documentation, and that the name
of CMU and The Regents of the University of California not be used in advertising or publicity pertaining to distribution of the software without specific written
permission.
CMU AND THE REGENTS OF THE UNIVERSITY OF CALIFORNIA DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL CMU OR THE REGENTS OF THE UNIVERSITY OF CALIFORNIA BE
LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE LOSS OF USE, DATA
OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE
USE OR PERFORMANCE OF THIS SOFTWARE.
Part 2 : Networks Associates Technology, Inc copyright notice (BSD)
Copyright (c) 2001-2003, Networks Associates Technology, Inc
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions
of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither
the name of the Networks Associates Technology, Inc nor the names of its contributors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Part 3: Cambridge Broadband Ltd. copyrightnotice (BSD)
Portions of this code are copyright (c) 2001-2003, Cambridge Broadband Ltd.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions
of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy The
name of Cambridge Broadband Ltd. may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Part 4: Sun Microsystems, Inc. copyright notice
(BSD)
Copyright (c) 2003 Sun Microsystems, Inc., 4150 Network
Circle, Santa Clara, California 95054, U.S.A.
All rights reserved.
Use is subject to license terms below. This distribution may include materials developed by third parties. Sun, Sun Microsystems, the Sun logo and Solaris
are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the following conditions are met: yy Redistributions of source code must retain the above copyright notice,
this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of the Sun Microsystems, Inc. nor the
names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Part 5: Sparta, Inc copyright notice (BSD)
Copyright (c) 2003-2009, Sparta, Inc
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions
of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither
the name of Sparta, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Part 6: Cisco/BUPTNIC copyright notice (BSD)
Copyright (c) 2004, Cisco, Inc and Information Network
Center of Beijing University of Posts and Telecommunications.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions
of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither
the name of Cisco, Inc, Beijing University of Posts and Telecommunications, nor the names of their contributors may be used to endorse or promote products
derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Part 7: Fabasoft R&D Software Software GmbH & Co KG copyright Notice (BSD)
Copyright (c) Fabasoft R&D Software GmbH & Co KG, 2003oss@fabasoft.com
Author: Bernhard Penz
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: yy Redistributions
of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy The
name of Fabasoft R&D Software GmbH & Co KG or any of its subsidiaries, brand or product names may not be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDER “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
COPYRIGHT HOLDER BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Part 8: Apple Inc. copyright notice (BSD)
Copyright (c) 2007 Apple Inc.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution. 3. Neither the name of Apple Inc. (“Apple”) nor the names of its contributors may be used to endorse or promote
products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY APPLE AND ITS CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL APPLE OR ITSCONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Part 9: ScienceLogic, LLC copyright notice(BSD)
Copyright (c) 2009, ScienceLogic, LLC
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions aremet: yy Redistributions
of source code must retain the above copyright notice, this list of conditions and the following disclaimer. yy Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither
the name of ScienceLogic, LLC nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE
The MIT License
Some software components of this product incorporate source code covered under the MIT license as follows
MIT License 2.0
- Acewidget, bettermeans, jquery-ui, libxml, libxml2, Mesa3D-MesaLib,mwEmbed,OpenGL Samples Pack, Wide Studio, xorg-server, dropbear-2012.55,
ncurses-5.7
Copyright (c) 2011, The Dojo Foundation
Copyright 2010, AUTHORS.txt (http://jqueryui.com/about)
Dual licensed under the MIT or GPL Version 2 licenses.
- http://jquery.org/license
- http://docs.jquery.com/UI/Widget
Copyright Daniel Veillard
Copyright Igor Zlatovic <igor@zlatkovic.com>
Copyright Aleksey Sanin
Copyright Gary Pennington <Gary.Pennington@uk.sun.com>
Copyright Alfred Mickautsch <alfred@mickautsch.de>
Copyright Bjorn Reese <bjorn.reese@systematic.dk>
Copyright Joel W. Reed
Copyright William Brack <wbrack@mmm.com.hk>
Copyright (c) 2007-2010 The Khronos Group Inc.
Copyright Atish Kumar Patra
Copyright (c) 2006 Free Software Foundation, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the
Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software,
and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Mozilla Public License
Since we, at Hanwha Techwin, used the Mozilla Firefox component without modifying the source code according to the MOZILLA Public license 1.1, we
are not obliged to provide the source code of the corresponding component.
•Version 1.1
1. Definitions.
1.0.1. "Commercial Use" means distribution or otherwise making the Covered Code available to a third party.
1.1. "Contributor" means each entity that creates or contributes to the creation of Modifications.
1.2.
"Contributor Version" means the combination of the Original Code, prior Modifications used by a Contributor, and the Modifications made by that particular Contributor.
1.3. "Covered Code" means the Original Code or Modifications or the combination of the Original Code and Modifications, in each case including portions thereof.
1.4. "Electronic Distribution Mechanism" means a mechanism generally accepted in the software development community for the electronic transfer of data.
1.5. "Executable" means Covered Code in any form other than Source Code.
1.6. "Initial Developer" means the individual or entity identified as the Initial Developer in the Source Code notice required by Exhibit A.
1.7. "Larger Work" means a work which combines Covered Code or portions thereof with code not governed by the terms of this License.
1.8. "License" means this document.
1.8.1. "Licensable" means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the
rights conveyed herein.
1.9. "Modifications" means any addition to or deletion from the substance or structure of either the Original Code or any previous Modifications. When Covered Code is
released as a series of files, a Modification is:
A. Any addition to or deletion from the contents of a file containing Original Code or previous Modifications.
B. Any new file that contains any part of the Original Code or previous Modifications.
1.10. "Original Code" means Source Code of computer software code which is described in the Source Code notice required by Exhibit A as Original Code, and which,
at the time of its release under this License is not already Covered Code governed by this License.
1.10.1. "Patent Claims" means any patent claim(s), now owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any patent
Licensable by grantor.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface
definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another
well known, available Covered Code of the Contributor’s choice. The Source Code can be in a compressed or archival form, provided the appropriate decompression or
de-archiving software is widely available for no charge.
1.12. "You’’ (or "Your") means an individual or a legal entity exercising rights under, and complying with all of the terms of, this License or a future version of this License
issued under Section 6.1. For legal entities, "You’’ includes any entity which controls, is controlled by, or is under common control with You. For purposes of this
definition, "control’’ means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of
more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
2. Source Code License.
2.1. The Initial Developer Grant. The Initial Developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property
claims:
(a) under intellectual property rights (other than patent or trademark) Licensable by Initial Developer to use, reproduce, modify, display, perform, sublicense and
distribute the Original Code (or portions thereof) with or without Modifications, and/or as part of a Larger Work; and
(b) under Patents Claims infringed by the making, using or selling of Original Code, to make, have made, use, practice, sell, and offer for sale, and/or otherwise
dispose of the Original Code (or portions thereof).
(c) the licenses granted in this Section 2.1(a) and (b) are effective on the date Initial Developer first distributes Original Code under the terms of this License.
(d) Notwithstanding Section 2.1(b) above, no patent license is granted: 1) for code that You delete from the Original Code; 2) separate from the Original Code; or
3) for infringements caused by: i) the modification of the Original Code or ii) the combination of the Original Code with other software or devices.
2.2. Contributor Grant. Subject to third party intellectual property claims, each Contributor hereby grants You a world-wide, royalty-free, non-exclusive license
(a) under intellectual property rights (other than patent or trademark) Licensable by Contributor, to use, reproduce, modify, display, perform, sublicense and
distribute the Modifications created by such Contributor (or portions thereof) either on an unmodified basis, with other Modifications, as Covered Code and/
or as part of a Larger Work; and
(b) under Patent Claims infringed by the making, using, or selling of Modifications made by that Contributor either alone and/or in combination with its
Contributor Version (or portions of such combination), to make, use, sell, offer for sale, have made, and/or otherwise dispose of: 1) Modifications made by
that Contributor (or portions thereof); and 2) the combination of Modifications made by that Contributor with its Contributor Version (or portions of such
combination).
(c) the licenses granted in Sections 2.2(a) and 2.2(b) are effective on the date Contributor first makes Commercial Use of the Covered Code.
(d) Notwithstanding Section 2.2(b) above, no patent license is granted: 1) for any code that Contributor has deleted from the Contributor Version; 2) separate from the
Contributor Version; 3) for infringements caused by: i) third party modifications of Contributor Version or ii) the combination of Modifications made by that Contributor
with other software (except as part of the Contributor Version) or other devices; or 4) under Patent Claims infringed by Covered Code in the absence of Modifications
made by that Contributor.
3. Distribution Obligations.
3.1. Application of License. The Modifications which You create or to which You contribute are governed by the terms of this License, including without limitation Section
2.2. The Source Code version of Covered Code may be distributed only under the terms of this License or a future version of this License released under Section 6.1,
and You must include a copy of this License with every copy of the Source Code You distribute. You may not offer or impose any terms on any Source Code version that
alters or restricts the applicable version of this License or the recipients’ rights hereunder. However, You may include an additional document offering the additional rights
described in Section 3.5.
3.2. Availability of Source Code. Any Modification which You create or to which You contribute must be made available in Source Code form under the terms of this
License either on the same media as an Executable version or via an accepted Electronic Distribution Mechanism to anyone to whom you made an Executable version
available; and if made available via Electronic Distribution Mechanism, must remain available for at least twelve (12) months after the date it initially became available, or
at least six (6) months after a subsequent version of that particular Modification has been made available to such recipients. You are responsible for ensuring that the
Source Code version remains available even if the Electronic Distribution Mechanism is maintained by a third party.
3.3. Description of Modifications. You must cause all Covered Code to which You contribute to contain a file documenting the changes You made to create that Covered
Code and the date of any change. You must include a prominent statement that the Modification is derived, directly or indirectly, from Original Code provided by the Initial
Developer and including the name of the Initial Developer in (a) the Source Code, and (b) in any notice in an Executable version or related documentation in which You
describe the origin or ownership of the Covered Code.
3.4. Intellectual Property Matters
(a) Third Party Claims. If Contributor has knowledge that a license under a third party’s intellectual property rights is required to exercise the rights granted by such
Contributor under Sections 2.1 or 2.2, Contributor must include a text file with the Source Code distribution titled "LEGAL’’ which describes the claim and the party
making the claim in sufficient detail that a recipient will know whom to contact. If Contributor obtains such knowledge after the Modification is made available as
described in Section 3.2, Contributor shall promptly modify the LEGAL file in all copies Contributor makes available thereafter and shall take other steps (such as
notifying appropriate mailing lists or newsgroups) reasonably calculated to inform those who received the Covered Code that new knowledge has been obtained.
(b) Contributor APIs. If Contributor’s Modifications include an application programming interface and Contributor has knowledge of patent licenses which are reasonably
necessary to implement that API, Contributor must also include this information in the LEGAL file.
(c) Representations.
Contributor represents that, except as disclosed pursuant to Section 3.4(a) above, Contributor believes that Contributor’s Modifications are Contributor’s original
creation(s) and/or Contributor has sufficient rights to grant the rights conveyed by this License.
3.5. Required Notices. You must duplicate the notice in Exhibit A in each file of the Source Code. If it is not possible to put such notice in a particular Source Code file
due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created
one or more Modification(s) You may add your name as a Contributor to the notice described in Exhibit A. You must also duplicate this License in any documentation for
the Source Code where You describe recipients’ rights or ownership rights relating to Covered Code. You may choose to offer, and to charge a fee for, warranty, support,
indemnity or liability obligations to one or more recipients of Covered Code. However, You may do so only on Your own behalf, and not on behalf of the Initial Developer
or any Contributor. You must make it absolutely clear than any such warranty, support, indemnity or liability obligation is offered by You alone, and You hereby agree to
indemnify the Initial Developer and every Contributor for any liability incurred by the Initial Developer or such Contributor as a result of warranty, support, indemnity or
liability terms You offer.
3.6. Distribution of Executable Versions. You may distribute Covered Code in Executable form only if the requirements of Section 3.1-3.5 have been met for that Covered
Code, and if You include a notice stating that the Source Code version of the Covered Code is available under the terms of this License, including a description of how
and where You have fulfilled the obligations of Section 3.2. The notice must be conspicuously included in any notice in an Executable version, related documentation or
collateral in which You describe recipients’ rights relating to the Covered Code. You may distribute the Executable version of Covered Code or ownership rights under
a license of Your choice, which may contain terms different from this License, provided that You are in compliance with the terms of this License and that the license
for the Executable version does not attempt to limit or alter the recipient’s rights in the Source Code version from the rights set forth in this License. If You distribute
the Executable version under a different license You must make it absolutely clear that any terms which differ from this License are offered by You alone, not by the
Initial Developer or any Contributor. You hereby agree to indemnify the Initial Developer and every Contributor for any liability incurred by the Initial Developer or such
Contributor as a result of any such terms You offer.
3.7. Larger Works. You may create a Larger Work by combining Covered Code with other code not governed by the terms of this License and distribute the Larger Work
as a single product. In such a case, You must make sure the requirements of this License are fulfilled for the Covered Code.
4. Inability to Comply Due to Statute or Regulation.
If it is impossible for You to comply with any of the terms of this License with respect to some or all of the Covered Code due to statute, judicial order, or regulation then
You must: (a) comply with the terms of this License to the maximum extent possible; and (b) describe the limitations and the code they affect. Such description must
be included in the LEGAL file described in Section 3.4 and must be included with all distributions of the Source Code. Except to the extent prohibited by statute or
regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it.
5. Application of this License.
This License applies to code to which the Initial Developer has attached the notice in Exhibit A and to related Covered Code.
6. Versions of the License.
6.1. New Versions. Netscape Communications Corporation (‘’Netscape’’) may publish revised and/or new versions of the License from time to time. Each version will be
given a distinguishing version number.
6.2. Effect of New Versions. Once Covered Code has been published under a particular version of the License, You may always continue to use it under the terms of that
version. You may also choose to use such Covered Code under the terms of any subsequent version of the License published by Netscape. No one other than Netscape
has the right to modify the terms applicable to Covered Code created under this License.
6.3. Derivative Works. If You create or use a modified version of this License (which you may only do in order to apply it to code which is not already Covered Code
governed by this License), You must (a) rename Your license so that the phrases "Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL", "NPL" or any confusingly similar
phrase do not appear in your license (except to note that your license differs from this License) and (b) otherwise make it clear that Your version of the license contains
terms which differ from the Mozilla Public License and Netscape Public License. (Filling in the name of the Initial Developer, Original Code or Contributor in the notice
described in Exhibit A shall not of themselves be deemed to be modifications of this License.)
7. DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN "AS IS’’ BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-
INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU. SHOULD ANY COVERED CODE PROVE
DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING,
REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS
AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
8. TERMINATION.
8.1. This License and the rights granted hereunder will terminate automatically if You fail to comply with terms herein and fail to cure such breach within 30 days of
becoming aware of the breach. All sublicenses to the Covered Code which are properly granted shall survive any termination of this License. Provisions which, by their
nature, must remain in effect beyond the termination of this License shall survive.
8.2. If You initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against Initial Developer or a Contributor (the Initial Developer
or Contributor against whom You file such action is referred to as "Participant") alleging that:
(a) such Participant’s Contributor Version directly or indirectly infringes any patent, then any and all rights granted by such Participant to You under Sections 2.1 and/
or 2.2 of this License shall, upon 60 days notice from Participant terminate prospectively, unless if within 60 days after receipt of notice You either: (i) agree in writing
to pay Participant a mutually agreeable reasonable royalty for Your past and future use of Modifications made by such Participant, or (ii) withdraw Your litigation claim
with respect to the Contributor Version against such Participant. If within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed
upon in writing by the parties or the litigation claim is not withdrawn, the rights granted by Participant to You under Sections 2.1 and/or 2.2 automatically terminate at
the expiration of the 60 day notice period specified above.
(b) any software, hardware, or device, other than such Participant’s Contributor Version, directly or indirectly infringes any patent, then any rights granted to You by such
Participant under Sections 2.1(b) and 2.2(b) are revoked effective as of the date You first made, used, sold, distributed, or had made, Modifications made by that
Participant.
8.3. If You assert a patent infringement claim against Participant alleging that such Participant’s Contributor Version directly or indirectly infringes any patent where
such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the reasonable value of the licenses granted by such
Participant under Sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license.
8.4. In the event of termination under Sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by
You or any distributor hereunder prior to termination shall survive termination.
9. LIMITATION OF LIABILITY.
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE
INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE, OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO
ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN
IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY
FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY’S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY
NOT APPLY TO YOU. 10. U.S. GOVERNMENT END USERS.
The Covered Code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of "commercial computer software" and "commercial
computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through
227.7202-4 (June 1995), all U.S. Government End Users acquire Covered Code with only those rights set forth herein.
11. MISCELLANEOUS.
This License represents the complete agreement concerning subject matter hereof. If any provision of this License is held to be unenforceable, such provision shall
be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions (except to the extent applicable law, if
any, provides otherwise), excluding its conflictof-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity chartered or registered
to do business in the United States of America, any litigation relating to this License shall be subject to the jurisdiction of the Federal Courts of the Northern District of
California, with venue lying in Santa Clara County, California, with the losing party responsible for costs, including without limitation, court costs and reasonable attorneys’
fees and expenses. The application of the United Nations Convention on Contracts for the International Sale of Goods is expressly excluded. Any law or regulation which
provides that the language of a contract shall be construed against the drafter shall not apply to this License.
12. RESPONSIBILITY FOR CLAIMS.
As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under
this License and You agree to work with Initial Developer and Contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be
deemed to constitute any admission of liability.
13. MULTIPLE-LICENSED CODE.
Initial Developer may designate portions of the Covered Code as Multiple-Licensed. Multiple-Licensedmeans that the Initial Developer permits you to utilize portions of
the Covered Code under Your choice of the MPL or the alternative licenses, if any, specified by the Initial Developer in the file described in Exhibit A.
EXHIBIT A -Mozilla Public License.
The contents of this file are subject to the Mozilla Public License Version 1.1 (the "License"); you may not use this file except in compliance with the License. You may
obtain a copy of the License at http://www.mozilla.org/MPL/Software distributed under the License is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
KIND, either express or implied. See the License for the specific language governing rights and limitations under the License.
The Original Code is ___________________________________.
The Initial Developer of the Original Code is ________________________. Portions created by ______________________ are Copyright (C) ______
_______________________. All Rights Reserved.
Contributor(s): ______________________________________.
Alternatively, the contents of this file may be used under the terms of the _____ license (the [___] License), in which case the provisions of [______] License are applicable
instead of those above. If you wish to allow use of your version of this file only under the terms of the [____] License and not to allow others to use your version of this file
under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provisions required by the [___] License. If you do not
delete the provisions above, a recipient may use your version of this file under either the MPL or the [___] License."
[NOTE: The text of this Exhibit A may differ slightly from the text of the notices in the Source Code files of the Original Code. You should use the text of this Exhibit A
rather than the text found in the Original Code Source Code for Your Modifications
The Independent JPEG Group’s JPEG Software
The software included in this product contains copyrighted software that is licensed under the JPEG license.
•JPEG license
- Code project . Generating Outline OpenGL, Libjpeg
This distribution contains the sixth public release of the Independent JPEG Group’s free JPEG software. You are welcome to redistribute this software and to use it for
any purpose, subject to the conditions under LEGAL ISSUES, below.
Serious users of this software (particularly those incorporating it into larger programs) should contact IJG at jpeg-info@uunet.uu.net to be added to our electronic mailing
list. Mailing list members are notified of updates and have a chance to participate in technical discussions, etc.
This software is the work of Tom Lane, Philip Gladstone, Jim Boucher, Lee Crocker, Julian Minguillon, Luis Ortiz, George Phillips, Davide Rossi, Guido Vollbeding, Ge’
Weijers, and other members of the Independent JPEG Group.
IJG is not affiliated with the official ISO JPEG standards committee.
LEGAL ISSUES
============
In plain English:
1.
We don’t promise that this software works. (But if you find any bugs, please let us know!)
2. You can use this software for whatever you want. You don’t have to pay us.
3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you’ve used the
IJG code.
In legalese:
The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for
a particular purpose. This software is provided "AS IS", and you, its user, assume the entire risk as to its quality and accuracy.
This software is copyright (C) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these conditions:
(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered;
and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation.
(2) If only executable code is distributed, then the accompanying documentation must state that "this software is based in part on the work of the Independent
JPEG Group".
(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY
for damages of any kind.
These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge
us.
Permission is NOT granted for the use of any IJG author’s name or company name in advertising or publicity relating to this software or products derived from it.
This software may be referred to only as "the Independent JPEG Group’s software".
We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are assumed by
the product vendor.
ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor of its copyright holder, Aladdin Enterprises of Menlo Park, CA.
ansi2knr.c is NOT covered by the above copyright and conditions, but instead by the usual distribution terms of the Free Software Foundation; principally, that
you must include source code if you redistribute it. (See the file ansi2knr.c for full details.) However, since ansi2knr. c is not needed as part of any program
generated from the IJG code, this does not limit you more than the foregoing paragraphs do.
The Unix configuration script "configure" was produced with GNU Autoconf. It is copyright by the Free Software Foundation but is freely distributable. The same
holds for its supporting scripts (config.guess, config.sub, ltconfig, ltmain. sh). Another support script, install-sh, is copyright by M.I.T. but is also freely distributable.
It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM, AT&T, and Mitsubishi. Hence arithmetic coding cannot legally
be used without obtaining one or more licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software. (Since arithmetic
coding provides only a marginal gain over the unpatented Huffman mode, it is unlikely that very many implementations will support it.) So far as we are aware,
there are no patent restrictions on the remaining code.
The IJG distribution formerly included code to read and write GIF files. To avoid entanglement with the Unisys LZW patent, GIF reading support has been removed
altogether, and the GIF writer has been simplified to produce "uncompressed GIFs". This technique does not use the LZW algorithm; the resulting GIF files are
larger than usual, but are readable by all standard GIF decoders.
We are required to state that
"The Graphics Interchange Format(c) is the Copyright property of CompuServe Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated."
T-Kernel License
- This Product uses the Source Code of T-Kernel under T-License granted by the T-Engine Forum(www.t-engine.org)
T-License [License Agreement for Source Code of T-Kernel]
established by T-Engine Forum
on January 23, 2004
revised on June 17, 2004
revised on December 21, 2006
revised on March 24, 2009
Article 1. Scope of License Agreement
1. This License Agreement sets forth copyrights and the terms and conditions of use applicable to the source code of T-Kernel distributed by T-Engine Forum
and any derivative work created therefrom.
Article 2. Definition
1. "T-Kernel" means a real-time operating system controlled and distributed by T-Engine Forum on behalf of the copyright holder thereof.
2. "Source Code" means a source program, including related comments and documentations, for the T-Kernel and the Ported Source Code defined in Article 2.8
which is registered with T-Engine Forum.
3. "Hardware-dependent Part" means the part of the Source Code which depends on hardware and needs to be changed when the Source Code is ported and
operated on the target hardware, and is designated and separated as such part.
4. "Compiler-dependent Part" means the part of the Source Code which depends on compiler and needs to be changed when the Source Code is ported and
operated on the target hardware, and is designated and separated as such part.
5. "Header File" means the part of the Source Code which contains definitions necessary to develop application programs.
6. "T-Engine Hardware" means the hardware which is manufactured in accordance with the T-Engine Hardware specifications or the μT-Engine Hardware
specifications issued by T-Engine Forum, and registered with T-Engine Forum.
7. "Similar Hardware to T-Engine Hardware" means any hardware (including software which emulates hardware) other than that defined in Article 2.6 above, on
which the T-Kernel can be operated.
8. "Ported Source Code" means a source program produced from the Source Code by modifying only its Hardwaredependent Part and/or Compiler-dependent
Part to enable it to be operated on the T-Engine Hardware or the Similar Hardware to T-Engine Hardware. The Ported Source Code which is registered with
T-Engine Forum shall be included in the Source Code.
9. "Modified Source Code" means a source program modified from the Source Code for the purpose of improving its performance, increasing or decreasing its
function, and the like. The Ported Source Code shall not be included in the Modified Source Code.
10. "Binary Code" means an executable code form which is created by compiling programs, which include all or part of the Source Code or the Modified Source
Code.
11. "Derivative Work" means the Modified Source Code or the Binary Code.
12. "Embedded Product" means any product which operates with executable code form of the Source Code, the Modified Source Code or the Binary Code
loaded on its hardware.
13. "End User" means a consumer who uses the Embedded Product.
14. "System Developer" means any person who develops the Embedded Product by itself or has a third party develop the same, and provides, whether with or
without payment, the End User with the Embedded Product.
15. "Distributor of Modification" means any person who produces the Modified Source Code and, whether with or without payment, distributes the same to any
third party.
16. "Patch for Modification" means a difference, program, system, or the like in order to create the Modified Source Code from the Source Code or the Binary
Code thereof.
17. "Vicarious Execution of Patch Processing" means vicarious execution service to create the Modified Source Code applying the Patch for Modification to the
Source Code or the Binary Code thereof.
18. "Source Code User" means a person who uses the Source Code.
19. "Distribution" means any of the following acts:
1. to transmit a work to a large number of specific persons through the Internet communication, broadcasting, and the like;
2. to transmit a work to the general public through the Internet communication, broadcasting, and the like automatically in response to a request from the
public; and
3. to distribute a copy of a work to the general public or a large number of specific persons.
Article 3. Copyright
1. The copyrights of the Source Code shall be owned by Ken Sakamura.
Article 4. License of Source Code
1. As provided for in this Article, T-Engine Forum shall provide, and grant a license to use, the Source Code free of charge to any person who has taken the
necessary procedure for registration as prescribed by T-Engine Forum and agreed to the T-License.
2. The Source Code shall be distributed exclusively by T-Engine Forum. Any person who obtains the Source Code under Article 4.1 above shall not make any
re-Distribution of the Source Code.
3. In accordance with the license granted under Article 4.1 above, the Source Code User may perform the following acts:
1. to copy and/or modify the Source Code provided by T-Engine Forum hereunder for its own research, development and the like.
2. to run the Source Code provided by T-Engine Forum hereunder for its own research, development and the like.
3. to run the Source Code modified in accordance with the provision of Article 4.3 (1) above for its own research, development and the like.
4. to distribute the Binary Code created from the Source Code provided by T-Engine Forum hereunder or from the Source Code modified in accordance with
the provision of Article 4.3 (1) above.
4. In accordance with the license granted under Article 4.1 above, the System Developer may perform the following acts:
1. to perform any and all acts set forth in the Article 4.3 above.
2. to develop and manufacture the Embedded Product containing the Binary Code, and, whether with or without payment, provide the End User with the same
and make the Binary Code available to the End User on the Embedded Product.
5. The Source Code User and the System Developer shall be obligated to give a notice that the Source Code is used, in such a way as separately specified by
T-Engine Forum, when they use the Source Code or the Binary Code, or make the Binary Code available for the End User on the Embedded Product.
Article 5. Distribution of Modified Source Code
1. Any of A- members of T-Engine Forum may become the Distributor of Modification by obtaining the approval of T-Engine Forum through the registration
procedure as prescribed by the Forum provided that only the department of the A- member which has taken the registration procedure may distribute the
Modified Source Code in such a way as provided for in this Article as long as it holds the Amembership.
2. The Distributor of Modification may create the Modified Source Code based on the Source Code provided by T-Engine Forum and the Patch for Modification
to be applied to create such Modified Source Code from the Source Code.
3. The Distributor of Modification shall, prior to the distribution, inform T-Engine Forum of and register a name and description of the Modified Source Code in
such a way as specified by T-Engine Forum.
4. The Distributor of Modification shall determine the name of the Modified Source Code subject to the rules separately established by T-Engine Forum and
publish an appropriate notice as required by the rules on the Patch for Modification and the Modified Source Code.
5. The Distributor of Modification may distribute the Modified Source Code to a third party, whether with or without payment, provided that the Distributor of
Modification shall take the necessary measures to prohibit the third party from making the re-Distribution of the Modified Source Code.
6. Developer with the Patch for Modification. Provided, however, that the Distributor of Modification shall be obligated to confirm that the System Developer is
the Source Code User duly licensed under Article 4.1.
7. The Distributor of Modification may perform the Vicarious Execution of Patch Processing for the System Developer.
8. The System Developer shall not distribute the Modified Source Code in further modified form to any third party as a stand-alone software product.
9. The System Developer may, under the same obligation as imposed in Article 4.5, make the Embedded Product available for the End User through use of the
Patch for Modification distributed by the Distributor of Modification or the Derivative Works obtained through the Vicarious Execution of Patch Processing.
Article 6. Distribution and Registration of the Ported Source Code
1. The Source Code User and the System Developer may, whether with or without charge, distribute to any third party only the following parts of the Ported
Source Code on the T-Engine Hardware or the Similar Hardware to T-Engine Hardware:
1. The Hardware-dependent Part and/or Compiler-dependent Part; provided that the Source Code User and the System Developer shall inform T-Engine Forum
of, and T-Engine Forum may publish, a method for distributing said Part(s) to third parties.
2. The Header File; provided that the Header File shall be distributed together with the Binary Code of the Ported Source Code.
2. Any member of T-Engine Forum may request T-Engine Forum to register and distribute, as an original source code for T-Kernel, the Ported Source Code on
the T-Engine Hardware or the Similar Hardware to T-Engine Hardware.
3. Any member of T-Engine Forum who requests the distribution mentioned in the preceding paragraph shall accede to the following conditions:
1. The member shall confirm that the object hardware is the T-Engine Hardware or the Similar Hardware to T-Engine Hardware.
2. The member shall provide T-Engine Forum with a complete set of operational environment for the object hardware and T-Kernel free of charge when
requesting the distribution.
3. The member shall submit test results of the Ported Source Code to T-Engine Forum when requesting the distribution.
4. In the event that T-Engine Forum accepts the request mentioned in Article 6.2, T-Engine Forum shall register and distribute the Ported Source Code as the
Source Code for T-Kernel. Provided, however, that the Ported Source Code may be treated in the same way as the Modified Source Code until the time of
registration hereunder.
5. The provision set forth in Article 3 shall apply to the Ported Source Code registered in accordance with this Article.
Article 7. Use for Other Purpose
1. Any use of the Source Code, the Modified Source Code or the Ported Source Code other than those stipulated in Articles 4, 5 and 6 shall be subject to the
prior approval of T-Engine Forum.
Article 8. Limited Warranty
1. T-Engine Forum and the copyright holder of the Source Code warrant that the Source Code does not infringe third party’s copyrights. Provided, however, that
T-Engine Forum and the copyright holder of the Source Code make no warranty as to the Hardware-dependent Part and/or Compiler- dependent Part set forth
in Article 6.2 in the Ported Source Code by any third party.
2. Neither T-Engine Forum nor the copyright holder of the Source Code warrants that the Source Code will fit for any particular purpose of the Source Code
User.
3. Neither T-Engine Forum nor the copyright holder of the Source Code warrants that the Source Code does not infringe any third party’s industrial property
rights. In no event shall T-Engine Forum and the copyright holder of the Source Code be liable for any dispute which may arise between the Source Code User
and a third party in connection with the third party’s industrial property rights.
Article 9. Indemnity
1. Neither T-Engine Forum nor the copyright holder of the Source Code shall be liable for any damages (including, but not limited to, damages resulting from
loss of profit, business interruption, loss of business information or any other pecuniary damage) arising out of use or impossibility of use of the Source Code,
even if T-Engine Forum and the copyright holder have been informed of the possibility of such damages.
Article 10. Breach of Agreement
1. In case that T-Engine Forum considers that this License Agreement is breached or that the popularization of T-Kernel is obstructed, T-Engine Forum shall take
measures to correct such breach or such obstruction, take measures on the ground of copyright infringement, or take any other necessary measures against
the breaching person or the obstructing person, regardless of whether or not the said person is a member of T-Engine Forum.
2. In case of breach of this License Agreement by a member of T-Engine Forum, T-Engine Forum may take appropriate measures against the member; for
example, the member is disqualified from membership, depending on what kind of breach has been committed by it.
3. Any legal dispute which may arise in relation to any breach of this License Agreement shall be subject to the exclusive jurisdiction of the Tokyo District Court.
Article 11. Governing Law and Language
1. This License Agreement shall be governed by and interpreted under the laws of Japan.
2. This License Agreement is executed in both Japanese text and English text provided that the Japanese text shall govern the interpretation and performance
of this License Agreement.
Apache License 2.0
Component Name License URL
mDNSResponder_bonjour Apache License 2.0 http://www.apache.org/licenses/LICENSE-2.0
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
1. Definitions.
"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.
"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the
purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii)
ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License. "Source" form shall mean the preferred form for making
modifications, including but not limited to software source code, documentation source, and configuration files.
"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code,
generated documentation, and conversions to other media types.
"Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in
or attached to the work (an example is provided in the Appendix below).
"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial revisions,
annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works shall not
include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof.
"Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works
thereof, that is intentionally submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf
of the copyright owner. For the purposes of this definition, "submitted" means any form of electronic, verbal, or written communication sent to the Licensor or its
representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed
by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise
designated in writing by the copyright owner as "Not a Contribution." "Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a
Contribution has been received by Licensor and subsequently incorporated within the Work.
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-
charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and
such Derivative Works in Source or Object form.
3. Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge,
royaltyfree, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work, where
such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their
Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity (including a crossclaim or counterclaim in
a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted
to You under this License for that Work shall terminate as of the date such litigation is filed.
4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object
form, provided that You meet the following conditions:
(a) You must give any other recipients of the Work or Derivative Works a copy of this License; and
(b) You must cause any modified files to carry prominent notices stating that You changed the files; and
(c) You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from the Source form of the
Work, excluding those notices that do not pertain to any part of the Derivative Works; and
(d) If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You distribute must include a readable copy of the attribution
notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places:
within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or,
within a display generated by the Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE file are for informational
purposes only and do not modify the License. You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum
to the NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the License.
You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or
distribution of Your modifications, or for any such Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the
conditions stated in this License.
5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be
under the terms and conditions of this License, without any additional terms or conditions. Notwithstanding the above, nothing herein shall supersede or modify the
terms of any separate license agreement you may have executed with Licensor regarding such Contributions.
6. Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for
reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and eachContributor provides its Contributions) on an
"AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of
TITLE, NONINFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of
using or redistributing the Work and assume any risks associated with Your exercise of permissions under this License.
8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as
deliberate and grossly negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect, special, incidental, or
consequential damages of any character arising as a result of this License or out of the use or inability to use the Work (including but not limited to damages for loss
of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if such Contributor has been advised of the
possibility of such damages.
9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof, You may choose to offer, and charge a fee for, acceptance of
support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting such obligations, You may act only on Your
own behalf and on Your sole responsibility, not on behalf of any other Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for
any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability.
END OF TERMS AND CONDITIONS
APPENDIX: How to apply the Apache License to your work.
To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own identifying information.
(Don't include the brackets!) The text should be enclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name and
description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives.
Copyright [yyyy] [name of copyright owner]
Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License
at http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.
BZip2 License
This program, "bzip2", the associated library "libbzip2", and all documentation, are copyright (C) 1996-2007 Julian R Seward. All rights reserved.
Component Name License URL
bzip2-1.0.6 Bzip2 http://www.bzip.org/
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an
acknowledgment in the product documentation would be appreciated but is not required.
3. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
4. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Julian Seward, jseward@bzip.org
bzip2/libbzip2 version 1.0.5 of 10 December 2007
University of Illinois / NCSA Open Source License
Copyright (c) 1999-2007, The Board of Trustees of the University of Illinois All Rights Reserved.
Component Name License
iperf-2.0.5 University of Illinois / NCSA Open Source
Iperf performance test
Mark Gates
Ajay Tirumala
Jim Ferguson
Jon Dugan
Feng Qin
Kevin Gibbs
John Estabrook
National Laboratory for Applied Network Research
National Center for Supercomputing Applications
University of Illinois at Urbana-Champaign
http://www.ncsa.uiuc.edu
Permission is hereby granted, free of charge, to any person obtaining a copy of this software (Iperf) and associated documentation files (the "Software"), to deal
in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimers.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimers in the documentation and/or other
materials provided with the distribution.
Neither the names of the University of Illinois, NCSA, nor the names of its contributors may be used to endorse or promote products derived from this Software
without specific prior written permission. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
THE CONTIBUTORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
PHP 3.01 License
The PHP License, version 3.01 Copyright (c) 1999 - 2010 The PHP Group. All rights reserved.
Component Name License URL
php-5.2.17 PHP 3.01 http://www.php.net/distributions
Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. The name "PHP" must not be used to endorse or promote products derived from this software without prior written permission. For written permission,
please contact group@php.net.
4. Products derived from this software may not be called "PHP", nor may "PHP" appear in their name, without prior written permission from group@php.net.
You may indicate that your software works in conjunction with PHP by saying "Foo for PHP" instead of calling it "PHP Foo" or "phpfoo"
5. The PHP Group may publish revised and/or new versions of the license from time to time. Each version will be given a distinguishing version number. Once
covered code has been published under a particular version of the license, you may always continue to use it under the terms of that version. You may also
choose to use such covered code under the terms of any subsequent version of the license published by the PHP Group. No one other than the PHP Group
has the right to modify the terms applicable to covered code created under this License.
6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes PHP software, freely available from <http://www.
php.net/software/>".
THIS SOFTWARE IS PROVIDED BY THE PHP DEVELOPMENT TEAM ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE PHP DEVELOPMENT TEAM OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
This software consists of voluntary contributions made by many individuals on behalf of the PHP Group. The PHP Group can be contacted via Email at group@
php.net.
For more information on the PHP Group and the PHP project, please see <http://www.php.net>. PHP includes the Zend Engine, freely available at <http://www.
zend.com>.
zlib / libpng License
This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of
this software.
Component Name License URL
zlib-1.2.8 zlib / libpng http://zlib.net/
Copyright (C) 1995-2010 Jean-loup Gailly and Mark Adler
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an
acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly Mark Adler
jloup@gzip.org madler@alumni.caltech.edu
The data format used by the zlib library is described by RFCs (Request for Comments) 1950 to 1952 in the files http://www.ietf.org/rfc/rfc1950.txt (zlib format),
rfc1951.txt (deflate format) and rfc1952.txt (gzip format).
Any changes or modifications in construction of this device which are not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other
household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains
mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these
substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them
through your local, free battery return system.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Hanwha Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide
customers with more environmentally friendly products.
The Eco mark represents Hanwha Techwin's devotion to creating environmentally friendly products, and indicates
that the product satisfies the EU RoHS Directive.
Head Oce
86 Cheonggyecheon-ro Jung-gu Seoul 04541 Korea
Tel +82.2.729.5277, 5254 Fax +82.2.729.5489
www.hanwha-security.com
Hanwha Techwin America
100 Challenger Rd. Suite 700 Ridgeeld Park, NJ 07660
Toll Free +1.877.213.1222 Direct +1.201.325.6920
Fax +1.201.373.0124
Hanwha Techwin Europe
2nd Floor, No. 5 The Heights, Brooklands, Weybridge, Surrey,
KT13 0NY, UK
Tel +44.1932.82.6700 Fax +44.1932.82.6701