Table of Contents
Samsung WW60J4060LW User Manual
Displayed below is the user manual for WW60J4060LW by Samsung which is a product in the Washing Machines category. This manual has pages.
Related Manuals
Washing Machine
User manual
WW60J4*****
WW4000J-03578Q-02_EN.indd 1 4/24/2017 11:55:40 AM
2 English
Contents
Contents
Safety information 3
What you need to know about the safety instructions 3
Important safety symbols 3
Important safety precautions 4
Instructions about the WEEE 12
Installation 13
What’s included 13
Installation requirements 15
Step-by-step installation 17
Before you start 23
Initial settings 23
Laundry guidelines 23
Detergent drawer guidelines 26
Operations 29
Control panel 29
Simple steps to start 30
Cycle overview 31
Settings 34
Maintenance 35
Eco drum clean 35
Smart Check 36
Emergency drain 37
Cleaning 38
Recovery from freezing 41
Care against an extended time of disuse 41
Troubleshooting 42
Checkpoints 42
Information codes 46
Specications 48
Fabric care chart 48
Protecting the environment 49
Specication sheet 50
Information of main washing cycles 53
WW4000J-03578Q-02_EN.indd 2 4/24/2017 11:55:41 AM
English 3
Safety information
Safety information
Congratulations on your new Samsung washing machine. This manual contains important
information on the installation, use and care of your appliance. Please take some time to read
this manual to take full advantage of your washing machine’s many benets and features.
What you need to know about the safety instructions
Please read this manual thoroughly to ensure that you know how to safely and efciently
operate the extensive features and functions of your new appliance. Please store the manual
in a safe location close to the appliance for future reference. Use this appliance only for its
intended purpose as described in this instruction manual.
Warnings and Important Safety Instructions in this manual do not cover all possible
conditions and situations that may occur. It is your responsibility to use common sense,
caution and care when installing, maintaining and operating your washing machine.
Because the following operating instructions cover various models, the characteristics of your
washing machine may differ slightly from those described in this manual and not all warning
signs may be applicable. If you have any questions or concerns, contact your nearest service
centre or nd help and information online at www.samsung.com.
Important safety symbols
What the icons and signs in this user manual mean:
WARNING
Hazards or unsafe practices that may result in severe personal injury, death and/or property
damage.
CAUTION
Hazards or unsafe practices that may result in personal injury and/or property damage.
NOTE
Indicates that a risk of personal injury or material damage exists.
WW4000J-03578Q-02_EN.indd 3 4/24/2017 11:55:41 AM
4 English
Safety information
Safety information
These warning signs are here to prevent injury to yourself and others.
Please follow them explicitly.
After reading this manual, store it in a safe place for future reference.
Read all instructions before using the appliance.
As with any equipment that uses electricity and moving parts, potential hazards exist. To
safely operate this appliance, familiarize yourself with its operation and exercise care when
using it.
Important safety precautions
WARNING
To reduce the risk of re, electric shock, or injury to persons when
using your appliance, follow basic precautions, including the following:
1. This appliance is not to be used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
2. For use in Europe: This appliance can be used by children aged from 8
years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
3. Children should be supervised to ensure that they do not play with the
appliance.
4. If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualied persons in order to avoid a
hazard.
5. The new hose-sets supplied with the appliance are to be used and that
old hose-sets should not be reused.
WW4000J-03578Q-02_EN.indd 4 4/24/2017 11:55:41 AM
English 5
Safety information
6. For appliances with ventilation openings in the base, that a carpet must
not obstruct the openings.
7. For use in Europe: Children of less than 3 years should be kept away
unless continuously supervised.
CAUTION
8. In order to avoid a hazard due to inadvertent resetting of the thermal
cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
Critical installation warnings
WARNING
The installation of this appliance must be performed by a qualied technician or service
company.
• Failure to do so may result in electric shock, re, an explosion, problems with the product,
or injury.
The appliance is heavy, therefore take care when lifting it.
Plug the power cord into an AC 220 - 240 V / 50 Hz wall socket or higher and use the socket
for this appliance only. Never use an extension cord.
• Sharing a wall socket with other appliances using a power strip or extending the power
cord may result in electric shock or re.
• Ensure that the power voltage, frequency, and current are the same as those of the
product specications. Failure to do so may result in electric shock or re. Plug the power
plug into the wall socket rmly.
Remove all foreign substances such as dust or water from the power plug terminals and
contact points using a dry cloth on a regular basis.
• Unplug the power plug and clean it with a dry cloth.
• Failure to do so may result in electric shock or re.
• Plug the power plug into the wall socket so that the cord is running towards the oor.
If you plug the power plug into the socket in the opposite direction, the electric wires
within the cable may be damaged and this may result in electric shock or re.
WW4000J-03578Q-02_EN.indd 5 4/24/2017 11:55:42 AM
6 English
Safety information
Safety information
Keep all packaging materials out of the reach of children as these may be dangerous.
• If a child places a bag over its head, it may suffocate.
When the appliance, power plug or power cord is damaged, contact your nearest service
centre.
This appliance must be properly grounded.
Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.
• This may result in electric shock, re, an explosion, or problems with the product.
• Never plug the power cord into a socket that is not grounded correctly and make sure
that it is in accordance with local and national regulations.
Do not install this appliance near a heater or any inammable material.
Do not install this appliance in a humid, oily or dusty location, or in a location exposed to
direct sunlight or water (rain drops).
Do not install this appliance in a location exposed to low temperatures.
• Frost may cause the tubes to burst.
Do not install this appliance in a location where gas may leak.
• This may result in electric shock or re.
Do not use an electric transformer.
• This may result in electric shock or re.
Do not use a damaged power plug, damaged power cord, or loose wall socket.
• This may result in electric shock or re.
Do not pull or excessively bend the power cord.
Do not twist or tie the power cord.
Do not hook the power cord over a metal object, place a heavy object on the power cord,
insert the power cord between objects, or push the power cord into the space behind the
appliance.
• This may result in electric shock or re.
Do not pull the power cord when unplugging the power plug.
• Unplug the power plug by holding the plug.
• Failure to do so may result in electric shock or re.
This appliance should be positioned so that the power plug, the water supply taps, and the
drain pipes are accessible.
WW4000J-03578Q-02_EN.indd 6 4/24/2017 11:55:42 AM
English 7
Safety information
Installation cautions
CAUTION
This appliance should be positioned in such a way that the power plug is easily accessible.
• Failure to do so may result in electric shock or re due to electric leakage.
Install your appliance on a solid, level oor that can support its weight.
• Failure to do so may result in abnormal vibrations, movement, noise, or problems with
the product.
Critical usage warnings
WARNING
If the appliance is ooded, turn off the water & power supplies immediately and contact your
nearest service centre.
• Do not touch the power plug with wet hands.
• Failure to do so may result in electric shock.
If the appliance generates a strange noise, a burning smell, or smoke, unplug the power plug
immediately and contact your nearest service centre.
• Failure to do so may result in electric shock or re.
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without
touching the power plug. Do not touch the appliance or power cord.
• Do not use a ventilating fan.
• A spark may result in an explosion or re.
Do not let children play in or on the washing machine. In addition, when disposing of the
appliance, remove the washing machine door lever.
• If trapped inside the product, children may suffocate to death.
Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the
washing machine before using it.
Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or
other inammable or explosive substances.
• This may result in electric shock, re, or an explosion.
WW4000J-03578Q-02_EN.indd 7 4/24/2017 11:55:42 AM
8 English
Safety information
Safety information
Do not open the washing machine door by force while it is operating (high-temperature
washing/drying/spinning).
• Water owing out of the washing machine may result in burns or cause the oor to be
slippery. This may result in injury.
• Opening the door by force may result in damage to the product or injury.
Do not insert your hand under the washing machine while an operation is in progress.
• This may result in injury.
Do not touch the power plug with wet hands.
• This may result in electric shock.
Do not turn the appliance off by unplugging the power plug while an operation is in progress.
• Plugging the power plug into the wall socket again may cause a spark and result in
electric shock or re.
Do not let children or the inrm use this washing machine without proper supervision. Do
not let children climb in or onto the appliance.
• This may result in electric shock, burns or injury.
Do not insert your hand or a metal object under the washing machine while it is operating.
• This may result in injury.
Do not unplug the appliance by pulling the power cord. Always grip the plug rmly and pull
it straight out of the outlet.
• Damage to the power cord may cause a short-circuit, re and/or electric shock.
Do not attempt to repair, disassemble, or modify the appliance yourself.
• Do not use a fuse (such as copper, steel wire, etc.) other than a standard fuse.
• When the appliance needs to be repaired or reinstalled, contact your nearest service
centre.
• Failure to do so may result in electric shock, re, problems with the product, or injury.
If the water supply hose comes loose from the water tap and oods the appliance, unplug the
power plug.
• Failure to do so may result in electric shock or re.
Unplug the power plug when the appliance is not being used for long periods of time or
during a thunder or lightning storm.
• Failure to do so may result in electric shock or re.
If any foreign substance enters into the appliance, unplug the power plug and contact you
nearest Samsung Customer Service.
• This may result in electric shock or re.
Do not let children (or pets) play in or on your washing machine. The washing machine door
does not open easily from the inside and children may be seriously injured if trapped inside.
WW4000J-03578Q-02_EN.indd 8 4/24/2017 11:55:42 AM
English 9
Safety information
Usage cautions
CAUTION
When the washing machine is contaminated by a foreign substance such as detergent, dirt,
food waste, etc., unplug the power plug and clean the washing machine using a damp, soft
cloth.
• Failure to do so may result in discolouration, deformation, damage, or rust.
The front glass may be broken by a strong impact. Take care when using the washing
machine.
• If the glass is broken, it may result in injury.
After a water supply failure or when reconnecting the water supply hose, open the water tap
slowly.
Open the water tap slowly after a long period of non-use.
• The air pressure in the water supply hose or the water pipe may damage a product part
or result in a water leak.
If a draining error occurs during an operation, check if there is a draining problem.
• If the washing machine is used when it is ooded because of a draining problem, it may
result in electric shock or re.
Insert the laundry into the washing machine completely so that the laundry does not get
caught in the door.
• If laundry gets caught in the door, it may result in damage to the laundry or the washing
machine, or result in a water leak.
Turn the water supply off when the washing machine is not being used.
Ensure that the screws on the water supply hose connector are properly tightened.
• Failure to do so may result in property damage or injury.
Ensure that the rubber seal and front door glass are not contaminated by a foreign substance
(e.g. waste, thread, hair, etc.).
• If a foreign substance is caught in the door or the door is not completely closed, it may
cause a water leak.
Open the water tap and check if the water supply hose connector is rmly tightened and that
there is no water leak before using the product.
• If the screws on the water supply hose connector are loose, it may result in a water leak.
The product you have purchased is designed for domestic use only.
WW4000J-03578Q-02_EN.indd 9 4/24/2017 11:55:42 AM
10 English
Safety information
Safety information
Using the product for business purposes qualies as a product misuse. In this case, the
product will not be covered by the standard warranty provided by Samsung and no
responsibility can be attributed to Samsung for malfunctions or damages resulting from such
misuse.
Do not stand on the appliance or place objects (such as laundry, lighted candles, lighted
cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
• This may result in electric shock, re, problems with the product, or injury.
Do not spray volatile material such as insecticide onto the surface of the appliance.
• As well as being harmful to humans, this may result in electric shock, re or problems
with the product.
Do not place objects that generate electromagnetic elds near the washing machine.
• This may result in injury due to a malfunction.
Water drained during a high-temperature wash or drying cycle is hot. Do not touch the water.
• This may result in burns or injury.
Do not wash, spin, or dry water-proof seats, mats, or clothing (*) unless your appliance has a
special cycle for washing these items.
(*): Woollen bedding, rain covers, shing vests, ski pants, sleeping bags, diaper covers, sweat
suits, and bicycle, motor cycle and car covers, etc.
• Do not wash thick or hard mats even if the washing machine mark is on the care label.
This may result in injury or damage to the washing machine, walls, oor, or clothing due
to abnormal vibrations.
• Do not wash throw rugs or doormats with rubber backing. The rubber backing may come
off and stick to inside the drum, and this may result in malfunction such as a drainage
error.
Do not operate the washing machine when the detergent drawer is removed.
• This may result in electric shock or injury due to a water leak.
Do not touch the insides of the drum during or just after drying as it is hot.
• This may result in burns.
Do not insert your hand into the detergent drawer.
• This may result in injury as your hand may be caught by the detergent input device.
• The liquid detergent guide (applicable models only) is not used for powder detergent.
Remove the guide when using powder detergent.
Do not place any objects (such as shoes, food waste, animals) other than laundry into the
washing machine.
• This may result in damage to the washing machine, or injury and death in the case of
pets due to the abnormal vibrations.
WW4000J-03578Q-02_EN.indd 10 4/24/2017 11:55:42 AM
English 11
Safety information
Do not press the buttons using sharp objects such as pins, knifes, ngernails, etc.
• This may result in electric shock or injury.
Do not wash laundry contaminated by oils, creams or lotions usually found in skincare shops
or massage clinics.
• This may cause the rubber seal to become deformed and result in a water leak.
Do not leave metal objects such as safety pins, hair pins or bleach in the drum for long
periods of time.
• This may cause the drum to rust.
• If rust starts appearing on the surface of the drum, apply a (neutral) cleansing agent to
the surface and use a sponge to clean it. Never use a metal brush.
Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry
contaminated by dry cleaning detergent.
• This may result in spontaneous combustion or ignition due to the heat from the oxidation
of the oil.
Do not use water from water cooling/heating devices.
• This may result in problems with the washing machine.
Do not use natural hand-washing soap for the washing machine.
• If it hardens and accumulates inside the washing machine, it may result in problems with
the product, discolouration, rust, or bad odours.
Place socks and brassieres in a washing net and wash them with the other laundry.
Do not wash large laundry items such as bedding in the washing net.
• Failure to do so may result in injury due to abnormal vibrations.
Do not use hardened detergent.
• If it accumulates inside the washing machine, it may result in a water leak.
Make sure that the pockets of all the clothing items to be washed are empty.
• Hard, sharp objects such as coins, safety pins, nails, screws, or stones can cause extensive
damage to the appliance.
Do not wash clothing with large buckles, buttons or other heavy metal objects.
Sort the laundry by color on the basis of its colorfastness and select the recommended cycle,
water temperature and additional functions.
• This may result in discoloration or fabric damage.
Take care that children’s ngers are not caught in the door when you close it.
• Failure to do so may result in injury.
WW4000J-03578Q-02_EN.indd 11 4/24/2017 11:55:42 AM
12 English
Safety information
Safety information
Critical cleaning warnings
WARNING
Do not clean the appliance by spraying water directly onto it.
Do not use the a strong acidic cleaning agent.
Do not use benzene, thinner or alcohol to clean the appliance.
• This may result in discolouration, deformation, damage, electric shock or re.
Before cleaning or performing maintenance, unplug the appliance from the wall socket.
• Failure to do so may result in electric shock or re.
Instructions about the WEEE
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that
the product and its electronic accessories (e.g. charger, headset,
USB cable) should not be disposed of with other household waste
at the end of their working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they
purchased this product, or their local government ofce, for details
of where and how they can take these items for environmentally
safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for
disposal.
For information on Samsung’s environmental commitments and product specic regulatory
obligations e.g. REACH visit: samsung.com/uk/aboutsamsung/samsungelectronics/
corporatecitizenship/data_corner.html
WW4000J-03578Q-02_EN.indd 12 4/24/2017 11:55:43 AM
English 13
Installation
Installation
Follow these instructions carefully to ensure proper installation of the washing machine and
to prevent accidents when doing laundry.
What’s included
Make sure all the parts are included in the product package. If you have a problem with
the washing machine or the parts, contact a local Samsung customer centre or the retailer.
01
02
12
11
10
09
03
04
06
08
07
05
01 Release lever 02 Detergent drawer 03 Control panel
04 Door 05 Drum 06 Pump lter
07 Emergency drain tube 08 Filter cover 09 Worktop
10 Power plug 11 Drain hose 12 Levelling feet
WW4000J-03578Q-02_EN.indd 13 4/24/2017 11:55:43 AM
14 English
Installation
Installation
Spanner Bolt caps Hose guide
Cold water hose Hot water hose Cap xer
NOTE
• Bolt caps : The provided number (3 to 6) of bolt caps depends on the model.
• Hot water hose: Applicable models only.
WW4000J-03578Q-02_EN.indd 14 4/24/2017 11:55:44 AM
English 15
Installation
Installation requirements
Electrical supply and grounding
• AC 220-240 V / 50 Hz fuse or circuit
breaker is required
• Use an individual branch circuit specic
to the washing machine
To ensure proper grounding, the washing
machine comes with a power cord featuring
a three-prong grounding plug for use in a
properly installed and grounded outlet.
Check with a qualied electrician or
serviceperson if you are not sure about the
grounding.
Do not modify the provided plug. If it does
not t the outlet, call a qualied electrician
to install a proper outlet.
WARNING
• Do NOT use an extension cord.
• Use only the power cord that comes
with the washing machine.
• Do NOT connect the ground wire to
plastic plumbing, gas lines, or hot water
pipes.
• Improperly connected grounding
conductors may cause electric shock.
Water supply
A proper water pressure for this washing
machine is between 50 kPa and 800 kPa.
Water pressure less than 50 kPa may cause
the water valve not to close completely. Or,
it may take longer to ll the drum, causing
the washing machine to turn off. Water taps
must be within 120 cm from the rear of the
washing machine so that the provided inlet
hoses reach the washing machine.
To reduce the risk of leaks:
• Make sure water taps are easily
accessible.
• Turn off the taps when the washing
machine is not in use.
• Check for any leaks at the water inlet
hose ttings on a regular basis.
CAUTION
Before using the washing machine for the
rst time, check all connections at the water
valve and taps for any leaks.
Drain
Samsung recommends a standpipe in
height of 60-90 cm. The drain hose must
be connected through the hose clip to the
standpipe, and the standpipe must fully
cover the drain hose.
WW4000J-03578Q-02_EN.indd 15 4/24/2017 11:55:44 AM
16 English
Installation
Installation
Flooring
For best performance, the washing
machine must be installed on a solid oor.
Wood oors may need to be reinforced
to minimize vibration and/or unbalanced
loads. Carpeting and soft tile surfaces are
not a good resistance to vibrations and may
cause the washing machine to move slightly
during the spin cycle.
CAUTION
Do NOT install the washing machine on a
platform or a poorly supported structure.
Water temperature
Do not install the washing machine in areas
where water may freeze as the washing
machine always retains some water in its
water valves, pumps, and/or hoses. Frozen
water left in the connection parts may
cause damage to belts, the pump, and other
components of the washing machine.
Alcove or closet installation
Minimum clearance for stable operation:
Sides 25 mm Rear 50 mm
Top 25 mm Front 550 mm
If both the washing machine and a dryer
are installed in the same location, the front
of the alcove or closet must have at least
a 550 mm unobstructed air opening. Your
washing machine alone does not require a
specic air opening.
WW4000J-03578Q-02_EN.indd 16 4/24/2017 11:55:44 AM
English 17
Installation
Step-by-step installation
STEP 1 Select a location
Location requirements:
• Solid, level surface without carpeting or ooring that may obstruct ventilation
• Away from direct sunlight
• Adequate room for ventilation and wiring
• The ambient temperature is always higher than the freezing point (0 ˚C)
• Away from a heat source
STEP 2 Remove the shipping bolts
Unpack the product package and remove all
shipping bolts.
1. Loosen all shipping bolts on the rear of
the machine using the supplied spanner.
2. Fill the holes with the supplied plastic
bolt caps.
Keep the shipping bolts for future use.
WARNING
Packaging materials can be dangerous to children. Dispose all packaging material (plastic
bags, polystyrene, etc.) out of children’s reach.
WW4000J-03578Q-02_EN.indd 17 4/24/2017 11:55:45 AM
18 English
Installation
Installation
STEP 3 Adjust the levelling feet
1. Gently slide the washing machine into
position. Excessive force may damage
the levelling feet.
2. Level the washing machine by manually
adjusting the levelling feet.
3. When levelling is complete, tighten the
nuts using the spanner.
STEP 4 Connect the water hose
A
B
Connect the water hose to the water tap.
1. Remove the adaptor (A) from the water
hose (B).
2. Use a Philips screwdriver to loosen four
screws on the adaptor.
WW4000J-03578Q-02_EN.indd 18 4/24/2017 11:55:46 AM
English 19
Installation
C
3. Hold the adaptor and turn part (C) in the
arrow direction to loosen it by 5 mm (*).
C
4. Insert the adaptor into the water tap,
and tighten the screws while lifting up
the adaptor.
5. Turn part (C) in the arrow direction to
tighten it.
D
6. While holding down part (D), connect the
water hose to the adaptor. Then, release
part (D). The hose ts into the adaptor
with a clicking sound.
7. Connect the other end of the water
hose to the inlet valve on the back of
the washing machine. Turn the hose
clockwise to tighten.
WW4000J-03578Q-02_EN.indd 19 4/24/2017 11:55:47 AM
20 English
Installation
Installation
8. Open the water tap and check if there
are any leaks around the connection
areas. If there are water leaks, repeat the
steps above.
• If using a screw type of water tap,
connect the water hose to the water tap
as shown.
WARNING
Stop using the washing machine if there is a water leak, and contact a local Samsung service
centre. Otherwise, this may cause electric shock.
CAUTION
Do not stretch the water hose by force. If the hose is too short, replace the hose with a
longer, high-pressure hose.
NOTE
• After connecting the water hose to the adaptor, check if it is connected properly by
pulling the water hose downwards.
• Use a popular type of water taps. If the tap is square-shaped or too big, remove the
spacer ring before inserting the tap into the adaptor.
WW4000J-03578Q-02_EN.indd 20 4/24/2017 11:55:48 AM
English 21
Installation
For models with an additional hot water
inlet:
1. Connect the red end of the hot water
hose to the hot water inlet on the back
of the machine.
2. Connect the other end of the hot water
hose to the hot water tap.
Aqua hose (applicable models only)
A
The aqua hose alerts users of a risk of water
leaks. It senses the water ow and turns red
on the centre indicator (A) in case of a leak.
WW4000J-03578Q-02_EN.indd 21 4/24/2017 11:55:48 AM
22 English
Installation
Installation
STEP 5 Position the drain hose
The drain hose can be positioned in three ways:
A
Over the edge of a wash basin
The drain hose must be placed at a height
of between 60 cm and 90 cm (*) from the
oor. To keep the spout of the drain hose
bent, use the supplied plastic hose guide (A).
Secure the guide to the wall using a hook to
ensure stable drainage.
ln a sink drain pipe
The drain pipe must be above the sink
siphon so that the end of the hose is at least
60 cm above the oor.
ln a drain pipe
The drain pipe should be between 60 cm
and 90 cm high (*). It is advisable to use
a 65 cm high vertical pipe. Make sure the
drain hose is connected to the stand pipe at
a slant.
Drain standpipe requirements:
• Minimum diameter of 5 cm
• Minimum carry-away capacity of
60 litres per minute
STEP 6 Power on
Plug the power cord into a wall socket featuring an AC 220-240 V / 50 Hz approved electrical
outlet protected by a fuse or circuit breaker. Then, press Power to turn on the washing
machine.
WW4000J-03578Q-02_EN.indd 22 4/24/2017 11:55:48 AM
English 23
Before you start
Before you start
Initial settings
Run Calibration (recommended)
Calibration ensures accurate weight
detection by the washing machine. Make
sure the drum is empty before running
Calibration.
1. Power off, and then power on the
washing machine.
2. Hold down Temp. and Delay End
simultaneously for 3 seconds to enter
Calibration mode. The “Cb” message
appears.
3. Press Start/Pause to run the Calibration
cycle.
4. The drum will rotate clockwise and
counter-clockwise for about 3 minutes.
5. When the cycle is complete, “0” appears
on the display and the washing machine
will turn off automatically.
6. The washing machine is now ready for
use.
Laundry guidelines
STEP 1 Sort
Sort the laundry according to these
criteria:
• Care Label: Sort the laundry into cottons,
mixed bres, synthetics, silks, wools, and
rayon.
• Colour: Separate whites from colours.
• Size: Mixing different-sized items
together in the drum improves the
washing performance.
• Sensitivity: Wash delicate items
separately using an Easy Iron option for
pure, new woollen items, curtains, and
silk items. Check the labels on the items.
NOTE
Make sure to check the care label on the
clothing, and sort them accordingly before
starting the wash.
STEP 2 Empty pockets
Empty all the pockets of your laundry
items
• Metal objects such as coins, pins, and
buckles on clothing may damage other
laundry items as well as the drum.
Turn clothing with buttons and
embroideries inside out
• If pants or jacket zippers are open while
washing, the drum may be damaged.
Zippers should be closed and xed with
a string.
• Clothing with long strings may become
entangled with other clothes. Make sure
to tie the strings before starting the
wash.
WW4000J-03578Q-02_EN.indd 23 4/24/2017 11:55:48 AM
24 English
Before you start
Before you start
STEP 3 Use a laundry net
• Brassieres (water washable) must be
placed in a laundry net. Metal parts of
the brassieres may break through and
tear other laundry items.
• Small, light clothing such as socks,
gloves, stockings, and handkerchiefs
may become caught around the door.
Place them inside a ne laundry net.
• Do not wash the laundry net by itself
without other laundry. This may cause
abnormal vibrations that could move the
washing machine and result in injury.
STEP 4 Prewash (if necessary)
Select the Prewash option for the selected
course if the laundry is heavily soiled. When
selecting the pre wash option, make sure to
put powder-type detergent into the main
wash compartment.
STEP 5 Determine the load capacity
Do not overload the washing machine.
Overloading may cause the washing
machine to not wash properly. For the load
capacity for the type of clothing, see page
31.
NOTE
When washing bedding or bedding covers,
the wash time may be lengthened or the
spin efciency may be reduced. For bedding
or bedding covers, the recommended
maximum spin cycle speed is 800 rpm, and
the load capacity is 2.0 kg or less.
CAUTION
If the laundry is unbalanced and the “Ub”
information code is displayed, redistribute
the load. Unbalanced laundry may reduce
the spinning performance.
WW4000J-03578Q-02_EN.indd 24 4/24/2017 11:55:49 AM
English 25
Before you start
STEP 6 Apply a proper detergent type
The type of detergent depends on the type of fabric (cotton, synthetic, delicate items, wool),
colour, wash temperature, and degree of soiling. Always use “low suds” laundry detergent,
which is designed for automatic washing machines.
NOTE
• Follow the detergent manufacturer’s recommendations based on the weight of the
laundry, the degree of soiling, and the hardness of the water in your local area. If you are
not sure about the water hardness, contact a local water authority.
• Do not use detergent that tends to be hardened or solidied. This detergent may remain
after the rinse cycle, blocking the drain outlet.
CAUTION
When washing wool using the WOOL course, use only a neutral liquid detergent. If used
with the WOOL course, powder detergent may remain on the laundry and discolour the
laundry.
Laundry capsules
To get the best results from using laundry capsules, please follow these instructions.
1. Put the capsule in the bottom of the
empty drum towards the rear.
2. Put the laundry in the drum on top of
the capsule.
WW4000J-03578Q-02_EN.indd 25 4/24/2017 11:55:49 AM
26 English
Before you start
Before you start
CAUTION
For cycles using cold water or cycles that complete in less than one hour, it is recommended
to use a liquid detergent. Otherwise, the capsule may not dissolve completely.
Detergent drawer guidelines
The washing machine provides a three-compartment dispenser: the left compartment for the
main wash, the front-right for fabric softeners, and the rear-right for the preliminary wash.
A
01 Prewash compartment: Apply
prewash detergent or starch.
02 Main-wash compartment: Apply
main-wash detergent, water softener,
soaking detergent, bleach, and/or stain
removers.
03 Softener compartment: Apply
additives such as fabric softener. Do not
exceed the max line (A).
CAUTION
• Do not open the detergent drawer while the washing machine is operating.
• Do not use the following types of detergent:
• Tablet or capsule types
• Ball or net types
• To prevent the compartment clogging, concentrated or highly-enriched agents (fabric
softener or detergent) must be diluted with water before being applied.
• When Delay End is selected, do not apply detergent directly into the drum. Otherwise,
this may discolour the laundry. Use the detergent drawer when Delay End is selected.
WW4000J-03578Q-02_EN.indd 26 4/24/2017 11:55:50 AM
English 27
Before you start
To apply washing agents to the detergent drawer
1. Slide open the detergent drawer.
2. Apply laundry detergent to the
main-wash compartment as instructed
or recommended by the manufacturer.
A
3. Apply fabric softener to the softener
compartment. Do not exceed the max
line (A).
4. If you want to prewash, apply
prewash detergent to the prewash
compartment as instructed or
recommended by the manufacturer.
5. Close the detergent drawer.
WW4000J-03578Q-02_EN.indd 27 4/24/2017 11:55:50 AM
28 English
Before you start
Before you start
CAUTION
• Do not apply powder detergent to the
liquid container.
• Concentrated fabric softener must be
diluted with water before applied.
• Do not apply main-wash detergent to
the softener compartment.
WW4000J-03578Q-02_EN.indd 28 4/24/2017 11:55:51 AM
English 29
Operations
Operations
Control panel
01
05
02
03 04 06 07
08
09
01 Cycle Selector Turn the dial to select a cycle.
02 Display The display shows current cycle information and estimated time
remaining, or an information code when a problem occurs.
03 Temp. Press to change the water temperature for the current cycle.
04 Spin
Press to change the spinning speed for the current cycle.
• Rinse Hold (No indicator): The nal rinse process is suspended so
that the laundry remains in the water. To unload the laundry, run
a drain or spin process.
• No Spin : The drum does not spin after the nal drain process.
05 Options Press to select an option from Intensive, Prewash, and Rinse+. Press
again to deselect.
06 Delay End
Delay End lets you set the end time of the current cycle. Based
on your settings, the start time of the cycle will be determined
by the machine’s internal logic. For example, this setting is useful
for programming your machine to nish a wash at the time you
normally return home from work.
• Press to choose a preset unit of hours.
07 Bubble Soak Press to activate/deactivate the Bubble Soak function. This function
helps remove a wide variety of stubborn stains.
08 Power Press to turn on/off the washing machine.
09 Start/Pause Press to start or stop operation.
WW4000J-03578Q-02_EN.indd 29 4/24/2017 11:55:51 AM
30 English
Operations
Operations
Simple steps to start
1
4
6
2
53
1. Press Power to turn on the washing machine.
2. Turn the Cycle Selector to select a course.
3. Change the cycle settings (Temp. and Spin) as necessary.
4. To add an option, press Options. Use the button again to choose a preferred item.
5. The machine provides two easy to access buttons for Bubble Soak and Delay End for your
convenience. If you want to use one of these options, press the corresponding button.
6. Press Start/Pause.
To change the cycle during operation
1. Press Start/Pause to stop operation.
2. Select a different cycle.
3. Press Start/Pause again to start the new cycle.
WW4000J-03578Q-02_EN.indd 30 4/24/2017 11:55:51 AM
English 31
Operations
Cycle overview
Standard cycles
Cycle Description Max load (kg)
COTTON
• For cottons, bed linens, table linens, underwear,
towels, or shirts.
The washing time and the rinse count are
automatically adjusted according to the load.
Max
COTTON
• Optimal performance with lower energy
for cotton fabrics, bed linens, table linens,
underwear, towels, or shirts.
• For energy saving, the actual washing
temperature may be lower than specied.
Max
SYNTHETICS
• For blouses or shirts that are made of polyester
(diolen, trevira), polyamide (perlon, nylon), or
the like.
3
SPIN • Featuring an additional spin process to
effectively remove moisture from laundry. -
RINSE+SPIN • Featuring an additional rinse process after
applying fabric softener to the laundry. -
ECO DRUM CLEAN
• Cleans the drum by removing dirt and bacteria
from the drum.
• Perform once every 40 washes with no
detergent or bleach applied.
• Make sure the drum is empty.
• Do not use any cleaning agents for cleaning the
drum.
-
SUPER ECO WASH • Low temperature ecobubble cycle helps reduce
power consumption. 3
15’ QUICK WASH • For lightly soiled garments in less than 2.0 kg
that you want to wash quickly. 2
WW4000J-03578Q-02_EN.indd 31 4/24/2017 11:55:52 AM
32 English
Operations
Operations
Cycle Description Max load (kg)
WOOL
• Specic for machine-washable wool for loads
less than 1.5 kg.
• The wool course features gentle cradling
and soaking to protect the wool bres from
shrinkage/distortion.
• A neutral detergent is recommended.
1.5
BABY CARE
• Featuring a high-temperature wash and extra
rinses to help remove the remaining detergent
effectively.
3
OUTDOOR CARE
• For outdoor clothes, skiwear, and sportswear
that are made of functional materials such as
spandex, stretch, and micro-bre.
2
DARK GARMENT
• Featuring additional rinses and reduced
spinning to ensure that the laundry is washed
gently and rinsed thoroughly.
3
Options
Option Description
Intensive • For badly soiled laundry. The operation time for each cycle is
longer than normal.
Pre Wash • This will add a preliminary washing cycle before the main
wash cycle.
Rinse+ • Press this button to add additional rinse cycles.
WW4000J-03578Q-02_EN.indd 32 4/24/2017 11:55:52 AM
English 33
Operations
Delay End
You can set the washing machine to nish your wash automatically at a later time, choosing a
delay of between 1 to 19 hours (in 1 hour increments). The hour displayed indicates the time
the wash will nish.
1. Select a cycle. Then change the cycle settings if necessary.
2. Press Delay End repeatedly until a desired end time is set.
3. Press Start/Pause.
The corresponding indicator turns on with the clock running.
4. To cancel the Delay End, restart the washing machine by pressing Power.
Real-life case
You want to nish a two-hour course 3 hours later from now. For this, you add the Delay End
option to the current cycle with the 3-hour setting, and press Start/Pause at 2:00 p.m. Then,
what happens? The washing machine starts operating at 3:00 p.m., and ends at 5:00 p.m.
Provided below is the time line for this example.
2:00 pm
Set the Delay End to 3 hours
3:00 pm
Start
5:00 pm
End
WW4000J-03578Q-02_EN.indd 33 4/24/2017 11:55:52 AM
34 English
Operations
Operations
Settings
Child Lock
To prevent accidents by children, Child Lock
locks all buttons except for Power.
• To set the Child Lock function, hold
down Temp. and Spin simultaneously for
3 seconds.
• To release the Child Lock function, hold
down Temp. and Spin simultaneously for
3 seconds.
NOTE
• In the Child Lock state, you must rst
release the Child Lock if you want to add
detergent or laundry.
• Your setting will be kept even after
restarting the machine.
Sound On/Off
You can turn on or off the key. Your setting
will remain effective after you restart the
machine.
• To mute the sound, hold down Spin and
Options simultaneously for 3 seconds.
• To unmute the sound, hold down again
for 3 seconds.
WW4000J-03578Q-02_EN.indd 34 4/24/2017 11:55:53 AM
English 35
Maintenance
Maintenance
Keep the washing machine clean to prevent deteriorated performance and to preserve its life
cycle.
Eco drum clean
Perform this cycle regularly to clean the
drum and to remove bacteria from it.
1. Press Power to turn on washing
machine.
2. Turn the Cycle Selector to select ECO
DRUM CLEAN.
3. Press Start/Pause.
NOTE
The water temperature for ECO DRUM
CLEAN is set to 70 °C, which cannot be
changed.
CAUTION
Do not use any cleaning agents for cleaning
the drum. Chemical residue in the drum
deteriorates the washing performance.
ECO DRUM CLEAN reminder
• The ECO DRUM CLEAN reminder
appears on the main screen once every
40 washes. It is advisable to perform the
ECO DRUM CLEAN regularly.
• When you rst see this reminder,
you can ignore the reminder for
6 consecutive washes. From the 7th
wash, the reminder no longer appears.
However, it appears again on the second
40th wash.
WW4000J-03578Q-02_EN.indd 35 4/24/2017 11:55:53 AM
36 English
Maintenance
Maintenance
Smart Check
To enable this function, you must rst download the Samsung Smart Washer app at the
Play Store or the Apple Store, and install it on a mobile device featuring a camera function.
The Smart Check function has been
optimized for Galaxy & iPhone series
(applicable models only).
1. Press and hold Options and Delay End
simultaneously for 3 seconds to enter
the Smart Check mode.
2. The washing machine starts the self-
diagnosis procedure and displays
an information code if a problem is
detected.
3. Run the Samsung Smart Washer app
on your mobile device, and tap Smart
Check.
4. Put the mobile device close to the
washing machine’s display so that the
mobile device and the washing machine
face each other. Then, the information
code will be recognized automatically by
the app.
5. When the information code is
recognized correctly, the app provides
detailed information about the problem
with applicable solutions.
NOTE
• The function name, Smart Check, may
differ depending on the language.
• If there is strong reected light on the
washing machine display, the app may
fail to recognize the information code.
• If the app fails to recognize the Smart
Check code consecutively, enter the
information code manually onto the app
screen.
WW4000J-03578Q-02_EN.indd 36 4/24/2017 11:55:53 AM
English 37
Maintenance
Emergency drain
In case of a power failure, drain the water inside the drum before taking out the laundry.
A
1. Power off and unplug the washing
machine from the electrical outlet.
2. Gently press the top area of the lter
cover (A) to open.
B
3. Put an empty, spacious container around
the cover, and stretch the emergency
drain tube to the container while holding
the tube cap (B).
C
4. Open the tube cap and let water in the
Emergency drain tube (C) ow into the
container.
5. When done, close the tube cap, and
reinsert the tube. Then, close the lter
cover.
NOTE
Use a spacious container because the water
in the drum may be more than expected.
WW4000J-03578Q-02_EN.indd 37 4/24/2017 11:55:54 AM
38 English
Maintenance
Maintenance
Cleaning
Surface of the washing machine
Use a soft cloth with a nonabrasive household detergent. Do not spray water onto the
washing machine.
Mesh lter
Clean the mesh lter of the water hose once or twice a year.
1. Turn off the washing machine, and
unplug the power cord.
2. Close the water tap.
3. Loosen and disconnect the water hose
from the back of the washing machine.
Cover the hose with a cloth to prevent
water from gushing out.
4. Use pliers to pull out the mesh lter
from the inlet valve.
5. Submerge the mesh lter deeply in
water so that the threaded connector is
also submerged.
6. Dry the mesh lter completely in the
shade.
7. Reinsert the mesh lter into the inlet
valve, and reconnect the water hose to
the inlet valve.
8. Open the water tap.
NOTE
If the mesh lter is clogged, an information code of “4C” appears on the screen.
WW4000J-03578Q-02_EN.indd 38 4/24/2017 11:55:56 AM
English 39
Maintenance
Pump lter
It is advisable to clean the pump lter 5 or 6 times a year to prevent its clogging. A clogged
pump lter may reduce the bubble effect.
1. Turn off the washing machine, and
unplug the power cord.
2. Drain the remaining water inside the
drum. See the “Emergency drain”
section.
3. Gently press the top area of the lter
cover to open.
4. Turn the pump lter knob to the left, and
drain off the remaining water.
5. Clean the pump lter using soft brushes.
Make sure the drain pump propeller
inside the lter is unclogged.
6. Reinsert the pump lter, and turn the
lter knob to the right.
NOTE
• Some pump lters feature a safety knob
that is designed to prevent accidents
by children. To open the safety knob
of the pump lter, push in and turn it
anticlockwise. The spring mechanism of
the safety knob helps open the lter.
• To close the safety knob of the pump
lter, turn it clockwise. The spring makes
a rattling sound, which is normal.
NOTE
If the pump lter is clogged, an information code of “5C” appears on the screen.
WW4000J-03578Q-02_EN.indd 39 4/24/2017 11:55:57 AM
40 English
Maintenance
Maintenance
CAUTION
• Make sure the lter knob is closed properly after cleaning the lter. Otherwise, this may
cause a leak.
• Make sure the lter is inserted properly after cleaning it. Otherwise, this may cause an
operational failure or a leak.
Detergent Drawer
A
1. While holding down the release lever (A)
on the inner of the drawer, slide open
the drawer.
2. Remove the release lever and the liquid
detergent container from the drawer.
3. Clean the drawer components in owing
water using a soft brush.
4. Clean the drawer recess using a soft
brush.
5. Reinsert the release lever and the liquid
detergent container to the drawer.
6. Slide the drawer inward to close it.
WW4000J-03578Q-02_EN.indd 40 4/24/2017 11:55:58 AM
English 41
Maintenance
NOTE
To remove remaining detergent, perform the RINSE+SPIN cycle with the drum being empty.
Recovery from freezing
The washing machine may freeze when it drops below 0 °C.
1. Turn off the washing machine, and unplug the power cord.
2. Pour warm water over the water tap to loosen the water hose.
3. Disconnect the water hose, and soak it in warm water.
4. Pour warm water into the drum and leave it for about 10 minutes.
5. Reconnect the water hose to the water tap.
NOTE
If the washing machine still doesn’t operate normally, repeat the above steps until it operates
normally.
Care against an extended time of disuse
Avoid leaving the washing machine unused for an extended time. If this is the case, drain the
washing machine and unplug the power cord.
1. Turn the Cycle Selector to select a RINSE+SPIN.
2. Empty the drum, and press Start/Pause.
3. When the cycle is complete, close the water tap and disconnect the water hose.
4. Turn off the washing machine, and unplug the power cord.
5. Open the door to let air circulate through the drum.
WW4000J-03578Q-02_EN.indd 41 4/24/2017 11:55:58 AM
42 English
Troubleshooting
Troubleshooting
Checkpoints
If you encounter a problem with the washing machine, rst check the table below and try the
suggestions.
Problem Action
Does not start.
• Make sure the washing machine is plugged in.
• Make sure the door is properly closed.
• Make sure the water taps are open.
• Make sure to press or tap Start/Pause to start the washing
machine.
• Make sure Child Lock is not activated.
• Before the washing machine starts to ll, it will make a series of
clicking noises to check the door lock and does a quick drain.
• Check the fuse or reset the circuit breaker.
Water supply is
insufcient, or no
water is supplied.
• Fully open the water tap.
• Make sure the door is properly closed.
• Make sure the water supply hose is not frozen.
• Make sure the water supply hose is not kinked or clogged.
• Make sure there is sufcient water pressure.
After a cycle,
detergent remains in
the detergent drawer.
• Make sure the washing machine is running with sufcient water
pressure.
• Make sure the detergent is added to the centre of the detergent
drawer.
• Make sure the rinse cap is inserted properly.
• If using granular detergent, make sure the detergent selector is
in the upper position.
• Remove the rinse cap and clean the detergent drawer.
Excessive vibrations
or makes noise.
• Make sure the washing machine is installed on a level, solid
oor that is not slippery.
If the oor is not level, use the levelling feet to adjust the
height of the washing machine.
• Make sure the shipping bolts are removed.
• Make sure the washing machine is not contacting any other
object.
• Make sure the laundry load is balanced.
• The motor can cause noise during normal operation.
• Overalls or metal-decorated clothes can cause noise while being
washed. This is normal.
• Metal objects such as coins can cause noise. After washing,
remove these objects from the drum or lter case.
WW4000J-03578Q-02_EN.indd 42 4/24/2017 11:55:59 AM
English 43
Troubleshooting
Problem Action
Does not drain and/
or spin.
• Make sure the drain hose is straightened all the way to the
drain system. If you encounter a drain restriction, call for
service.
• Make sure the debris lter is not clogged.
• Close the door and press or tap Start/Pause. For your safety,
the washing machine will not tumble or spin unless the door is
closed.
• Make sure the drain hose is not frozen or clogged.
• Make sure the drain hose is connected to a drain system that is
not clogged.
• If the washing machine is not supplied with sufcient power,
the washing machine temporarily will not drain or spin.
As soon as the washing machine regains sufcient power, it will
operate normally.
The door does not
open.
• Press or tap Start/Pause to stop the washing machine.
• It may take a few moments for the door lock mechanism to
disengage.
• The door will not open until 3 minutes after the washing
machine has stopped or the power turned off.
• Make sure all the water in the drum is drained.
• The door may not open if water remains in the drum. Drain the
drum and open the door manually.
• Make sure the door lock light is off. The door lock light turns off
after the washing machine has drained.
Excessive suds.
• Make sure you use the recommended types of detergent as
appropriate.
• Use high efciency (HE) detergent to prevent oversudsing.
• Reduce the detergent amount for soft water, small loads, or
lightly soiled loads.
• Non-HE detergent is not recommended.
Cannot apply
additional detergent.
• Make sure the remaining amount of detergent and fabric
softener is not over the limit.
WW4000J-03578Q-02_EN.indd 43 4/24/2017 11:55:59 AM
44 English
Troubleshooting
Troubleshooting
Problem Action
Stops.
• Plug the power cord into a live electrical outlet.
• Check the fuse or reset the circuit breaker.
• Close the door and press the Start/Pause button to start the
washing machine.
For your safety, the washing machine will not tumble or spin
unless the door is closed.
• Before the washing machine starts to ll, it will make a series of
clicking noises to check the door lock and does a quick drain.
• There may be a pause or soak period in the cycle. Wait briey
and the washing machine may start.
• Make sure the mesh lter of the water supply hose at the water
taps are not clogged. Periodically clean the mesh lter.
• If the washing machine is not supplied with sufcient power,
the washing machine temporarily will not drain or spin. As soon
as the washing machine regains sufcient power, it will operate
normally.
Fills with the wrong
water temperature.
• Fully open both taps.
• Make sure the temperature selection is correct.
• Make sure the hoses are connected to the correct taps. Flush
water lines.
• Make sure the water heater is set to supply a minimum 120 °F
(49 °C) hot water at the tap. Also, check the water heater
capacity and recovery rate.
• Disconnect the hoses and clean the mesh lter. The mesh lter
may be clogged.
• While the washing machine lls, the water temperature may
change as the automatic temperature control feature checks
incoming water temperature. This is normal.
• While the washing machine lls, you may notice just hot and/or
just cold water going through the dispenser when cold or warm
temperatures are selected.
This is a normal function of the automatic temperature
control feature as the washing machine determines the water
temperature.
Load is wet at the
end of a cycle.
• Use the High or Extra High spin speed.
• Use high efciency (HE) detergent to reduce oversudsing.
• Load is too small. Small loads (one or two items) may become
unbalanced and not spin completely.
• Make sure the drain hose is not kinked or clogged.
WW4000J-03578Q-02_EN.indd 44 4/24/2017 11:55:59 AM
English 45
Troubleshooting
Problem Action
Leaks water.
• Make sure the door is properly closed.
• Make sure all hose connections are tight.
• Make sure the end of the drain hose is correctly inserted and
secured to the drain system.
• Avoid overloading.
• Use high efciency (HE) detergent to prevent oversudsing.
Has odours.
• Excessive suds collect in recesses and can cause foul odours.
• Run cleansing cycles to sanitize periodically.
• Clean the door seal (diaphragm).
• Dry the washing machine interior after a cycle has nished.
No bubbles are seen
(Bubbleshot models
only).
• Overloading may screen bubbles.
• Severely contaminated laundry may not generate bubbles.
If a problem persists, contact a local Samsung service centre.
WW4000J-03578Q-02_EN.indd 45 4/24/2017 11:55:59 AM
46 English
Troubleshooting
Troubleshooting
Information codes
If the washing machine fails to operate, you may see an information code on the screen.
Check the table below and try the suggestions.
Code Action
4C
Water is not supplied.
• Make sure the water taps are open.
• Make sure the water hoses are not clogged.
• Make sure the water taps are not frozen.
• Make sure the washing machine is operating with sufcient
water pressure.
• Make sure that the cold water tap and the hot water tap are
properly connected.
• Clean the mesh lter as it may be clogged.
4C2
• Make sure the cold water supply hose is rmly connected to
the cold water tap.
If it is connected to the hot water tap, the laundry may be
deformed with some cycles.
5C
Water is not draining.
• Make sure the drain hose is not frozen or clogged.
• Make sure the drain hose is positioned correctly, depending on
the connection type.
• Clean the debris lter as it may be clogged.
• Make sure the drain hose is straightened all the way to the
drain system.
• If the information code remains, contact a customer service
centre.
dC
Operating the washer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
OC
Water is overowed.
• Restart after spinning.
• If the information code remains on the display, contact a local
Samsung service centre.
LC, LC1
Check the drain hose.
• Make sure the end of the drain hose is placed on the oor.
• Make sure the drain hose is not clogged.
• If the information code remains, contact a customer service
centre.
WW4000J-03578Q-02_EN.indd 46 4/24/2017 11:55:59 AM
English 47
Troubleshooting
Code Action
Ub
Spinning does not work.
• Make sure laundry is spread out evenly.
• Make sure the washing machine is on a at, stable surface.
• Redistribute the load. If only one item of clothing needs
washing, such as a bathrobe or pair of jeans, the nal spin
result might be unsatisfactory, and an “Ub” check message will
be shown in the display.
3C
Check the motor for operation.
• Try restarting the cycle.
• If the information code remains, contact a customer service
centre.
UC
The electronic control needs to be checked.
• Check if power is supplied properly.
• If the information code remains, contact a customer service
centre.
Low voltage detected.
• Check if the power cord is plugged in.
• If the information code remains, contact a customer service
centre.
HC
High temperature heating check.
• If the information code remains, contact a customer service
centre.
1C
The Water Level sensor is not working properly.
• Try power off and restarting the cycle.
• If the information code remains, contact a customer service
centre.
AC
Check communications between main and sub PBAs.
• Try power off and restarting the cycle.
• If the information code remains, contact a customer service
centre.
If any information code keeps appearing on the screen, contact a local Samsung service
centre.
WW4000J-03578Q-02_EN.indd 47 4/24/2017 11:55:59 AM
48 English
Specications
Specications
Fabric care chart
The following symbols provide garment care directions. The care labels include four symbols
in this order: washing, bleaching, drying and ironing (and dry cleaning when necessary).
The use of symbols ensures consistency among garment manufacturers of domestic and
imported items. Follow the care label directions to maximize garment life and reduce laundry
problems.
Resistant material Do not iron
Delicate fabric Can be dry cleaned using any
solvent
Item can be washed at 95 ˚C Dry Clean
Item can be washed at 60 ˚C
Dry clean with perchloride,
lighter fuel, pure alcohol or
R113 only
Item can be washed at 40 ˚C Dry clean with aviation fuel,
pure alcohol or R113 only
Item can be washed at 30 ˚C Do not dry clean
Hand wash only Dry at
Dry clean only Can be hung to dry
Can be bleached in cold water Dry on clothes hanger
Do not bleach Tumble dry, normal heat
Can be ironed at 200 ˚C max Tumble dry, reduced heat
Can be ironed at 150 ˚C max Do not tumble dry
Can be ironed at 100 ˚C max
WW4000J-03578Q-02_EN.indd 48 4/24/2017 11:56:01 AM
English 49
Specications
Protecting the environment
• This appliance is manufactured from recyclable materials. If you decide to dispose of this
appliance, please observe local waste disposal regulations. Cut off the power cord so that
the appliance cannot be connected to a power source. Remove the door so that animals
and small children cannot get trapped inside the appliance.
• Do not exceed the detergent quantities recommended in the detergent manufacturer’s
instructions.
• Use stain removal products and bleaches before the wash cycle only when strictly
necessary.
• Save water and electricity by only washing full loads (the exact amount depends upon
the program used).
WW4000J-03578Q-02_EN.indd 49 4/24/2017 11:56:01 AM
50 English
Specications
Specications
Specication sheet
“ * “ Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Type Front loading washing machine
Model name WW60J4*****
Dimensions W600 x D450 x H850 (mm)
Water pressure 50 kPa - 800 kPa
NET weight 54.0 kg
Wash and spin capacity 6.0 kg
Power
consumption
Washing
and heating
220 V 2000 W
240 V 2400 W
Spin revolutions WW60J42**** WW60J40****
1200 rpm 1000 rpm
NOTE
The design and specications are subject to change without notice for quality improvement
purposes.
WW4000J-03578Q-02_EN.indd 50 4/24/2017 11:56:01 AM
English 51
Specications
According to Regulation (EU) No. 1061/2010
“*” Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Samsung
Model Name WW60J421***
Capacity kg 6.0
Energy Efciency on a scale from D (least efcient) to A+++ (most efcient) A+++
Annual energy consumption (It is based on 220 standard washing cycles
for standard cotton course at 60 °C and 40 °C at full and partial load, and
the consumption of off and left-on modes. Actual energy consumption
will depend on how the appliance is used.)
kWh/yr 122
Energy Consumption
The standard 60 °C cotton programme at full load kWh 0.64
The standard 60 °C cotton programme at partial load kWh 0.52
The standard 40 °C cotton programme at partial load kWh 0.40
Weighted power consumption of the off-mode. W0.48
Weighted power consumption of the left-on mode. W5.00
Annual water consumption (It is based on 220 standard washing cycles
for standard cotton course at 60 °C and 40 °C at full and partial load.
Actual water consumption will depend on how the appliance is used.)
L/yr 7300
Spin efciency class
Spin-drying efciency class on a scale from G (least efcient) to A (most efcient) B
Maximun Spin Speed rpm 1200
Residual moisture %53
The COTTON 60 °C and COTTON 40 °C programs are the ‘standard cotton 60 °C program’ and the
‘standard cotton 40 °C program’. They are suitable to clean normally soiled cotton laundry and they are the
most efcient (concerning water and energy consumption) for this type of laundry. In these programs the actual
water temperature may differ from the declared temperature. Please run Calibration Mode after the installation
(refer to the “Run Calibration (recommended)” section on page 23).
Program duration of the standard program
The standard 60 °C cotton programme at full load min 260
The standard 60 °C cotton programme at partial load min 240
The standard 40 °C cotton programme at partial load min 220
The duration of the left-on mode (Tl) min 2
Airborne acoustical noise emissions expressed in dB(A) re 1 pW and rounded to the nearest integer during the
washing and spinning phases for the standard 60 °C cotton programme at full load;
Wash dB (A) re 1 pW 55
Spin dB (A) re 1 pW 76
Free Standing
WW4000J-03578Q-02_EN.indd 51 4/24/2017 11:56:02 AM
52 English
Specications
Specications
According to Regulation (EU) No. 1061/2010
“*” Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Samsung
Model Name
WW60J426*** WW60J406***
Capacity kg 6.0
Energy Efciency on a scale from D (least efcient) to A+++ (most efcient) A+++
Annual energy consumption (It is based on 220 standard
washing cycles for standard cotton course at 60 °C and 40 °C
at full and partial load, and the consumption of off and left-on
modes. Actual energy consumption will depend on how the
appliance is used.)
kWh/yr 153
Energy Consumption
The standard 60 °C cotton programme at full load kWh 0.86
The standard 60 °C cotton programme at partial load kWh 0.62
The standard 40 °C cotton programme at partial load kWh 0.46
Weighted power consumption of the off-mode. W0.48
Weighted power consumption of the left-on mode. W5.00
Annual water consumption (It is based on 220 standard washing
cycles for standard cotton course at 60 °C and 40 °C at full and
partial load. Actual water consumption will depend on how the
appliance is used.)
L/yr 7300
Spin efciency class
Spin-drying efciency class on a scale from G (least efcient) to A (most efcient)
B C
Maximun Spin Speed rpm 1200 1000
Residual moisture %53 62
The COTTON 60 °C and COTTON 40 °C programs are the ‘standard cotton 60 °C program’ and the
‘standard cotton 40 °C program’. They are suitable to clean normally soiled cotton laundry and they are the
most efcient (concerning water and energy consumption) for this type of laundry. In these programs the actual
water temperature may differ from the declared temperature. Please run Calibration Mode after the installation
(refer to the “Run Calibration (recommended)” section on page 23).
Program duration of the standard program
The standard 60 °C cotton programme at full load min 250
The standard 60 °C cotton programme at partial load min 193
The standard 40 °C cotton programme at partial load min 173
The duration of the left-on mode (Tl) min 2
Airborne acoustical noise emissions expressed in dB(A) re 1 pW and rounded to the nearest integer during the
washing and spinning phases for the standard 60 °C cotton programme at full load;
Wash dB (A) re 1 pW 61 61
Spin dB (A) re 1 pW 77 76
Free Standing
WW4000J-03578Q-02_EN.indd 52 4/24/2017 11:56:02 AM
English 53
Specications
Information of main washing cycles
Model Cycles Temperature
(°C)
Capacity
(kg)
Cycle
Time
(min)
Residual
Moisture
Content (%)
Water
Consumption
(L/cycle)
Energy
Consumption
(kWh/Cycle)
1200
rpm
1000
rpm
WW60J421***
COTTON 20 3136 59 -38 0.28
COTTON
40 3220 53 -30 0.40
60 3240 53 -30 0.52
6260 53 -36 0.64
SYNTHETICS 40 3132 35 -36 0.45
WW60J426***
WW60J406***
COTTON 20 3118 59 65 38 0.32
COTTON
40 3173 53 62 30 0.46
60 3193 53 62 30 0.62
6250 53 62 36 0.86
SYNTHETICS 40 3131 35 40 36 0.49
The values on the table have been measured under the conditions specied in Standard
IEC60456/EN60456. Actual values will depend on how the appliance is used.
WW4000J-03578Q-02_EN.indd 53 4/24/2017 11:56:02 AM
Memo
WW4000J-03578Q-02_EN.indd 54 4/24/2017 11:56:02 AM
Memo
WW4000J-03578Q-02_EN.indd 55 4/24/2017 11:56:02 AM
QUESTIONS OR COMMENTS?
COUNTRY CALL OR VISIT US ONLINE AT
POLAND
801-172-678* lub +48 22 607-93-33*
Dedykowana infolinia do obsługi zapytań
dotyczących telefonów komórkowych: 801-
672-678* lub +48 22 607-93-33*
* (koszt połączenia według taryfy operatora)
www.samsung.com/pl/support
DC68-03578Q-02
WW4000J-03578Q-02_EN.indd 56 4/24/2017 11:56:02 AM