SilverNet SIL MICRO User Manual
Displayed below is the user manual for SIL MICRO by SilverNet which is a product in the Bridges & Repeaters category. This manual has pages.
Related Manuals
V1.0 www.silvernet.com
PRO RANGE
User Manual
PICO
MICRO
LITE
MAX
Pro Range User Manual 2
TABLE OF CONTENTS
Introduction ............................................................................................................................... 4
Supported Products ............................................................................................................... 4
Wireless Modes ..................................................................................................................... 4
System Requirements ............................................................................................................ 4
Packing list ................................................................................................................................. 5
The Enclosure and LED indicators .............................................................................................. 6
Configuration ............................................................................................................................. 7
Getting Started ...................................................................................................................... 7
Navigation .............................................................................................................................. 8
Status ......................................................................................................................................... 9
Overview .............................................................................................................................. 10
Realtime Graphs .................................................................................................................. 12
Admin Tab ................................................................................................................................ 13
System ................................................................................................................................. 13
Administration ..................................................................................................................... 15
SNMP ................................................................................................................................... 16
LED Configuration ................................................................................................................ 18
Backup/Flash Firmware ........................................................................................................ 19
Reboot ................................................................................................................................. 19
Services .................................................................................................................................... 21
Dynamic DNS ....................................................................................................................... 21
Network Tab ............................................................................................................................ 27
LAN Interface ....................................................................................................................... 28
DHCP Server ........................................................................................................................ 29
Wireless Interface ................................................................................................................ 32
Pro Range User Manual 3
Device Configuration ........................................................................................................... 33
Interface Configuration ........................................................................................................ 37
Wireless Security.................................................................................................................. 39
VLANS .................................................................................................................................. 42
Diagnostics ........................................................................................................................... 44
Standards ................................................................................................................................. 45
Declaration of Conformity ................................................................................................... 45
Warnings .................................................................................................................................. 46
Radio frequency Interference Requirements ....................................................................... 46
Troubleshooting ....................................................................................................................... 48
Warranty .................................................................................................................................. 48
Contact SilverNet ..................................................................................................................... 48
Copyright Information ............................................................................................................. 48
Other SilverNet Products ......................................................................................................... 49
Pro Range ............................................................................................................................. 49
Industrial Network Transmission ......................................................................................... 49
Intelligent Wi-Fi Solutions .................................................................................................... 49
Industry Leading Technical Support ..................................................................................... 49
Pro Range User Manual Introduction 4
INTRODUCTION
This User Guide describes the firmware version 2.1.3 and above which is integrated into all
Pro Range products provided by SilverNet Ltd.
SUPPORTED PRODUCTS
This manual covers all GEN4 products listed below:
• PICO
• MICRO
• LITE
• MAX
For more information, visit www.silvernet.com
WIRELESS MODES
The Pro Range supports the following wireless modes:
• Station
• Station WDS
• Access Point
• Access Point WDS
SYSTEM REQUIREMENTS
• Windows XP, Windows Vista, Windows 7, Windows 8, Windows 10, Linux, or Mac OS X
• Web Browser: Mozilla Firefox, Apple Safari, Google Chrome, or Microsoft Internet Explorer
9 (or above)
Pro Range User Manual Packing list 5
PACKING LIST
Please check the following items in the package before installing the device
Wireless Radio 1 piece
User manual 1 copy
Cable Gland 1 piece
Mounting bracket 1 piece
Power over Ethernet Injector 1 piece
Power cable 1 piece
Set of screws 1 piece
Please contact your distributor immediately for any missing or damaged items.
Pro Range User Manual The Enclosure and LED indicators 6
THE ENCLOSURE AND LED INDICATORS
Mark
Name
Function
1
Reset Button
Press to reboot the device manually
Hold to rest the device to factory settings
2
Ethernet Port (PoE)
10/100Mbps Ethernet port and PoE power input (48V DC)
3
Ethernet link LED
“On/Blinking”: Power is being supplied and a link has been
established to the network.
“Off”: No power and/or the Ethernet port has no connection
4
75% Signal Rx LED
“On”: Signal Strength is at 75%
“Off”: Signal Strength not at 75%
5
100% Signal Rx LED
“On”: Signal Strength is at 100%
“Off”: Signal Strength not at 100%
“Blinking”: Device is in diagnostic mode
3
4
5
1
2
Pro Range User Manual Configuration 7
CONFIGURATION
GETTING STARTED
To access the Pro Range Configuration Interface, perform the following steps:
1. Configure the Ethernet adapter on your computer with a static IP address on the
192.168.0.x subnet (for example, IP address: 192.168.0.100 and subnet mask: 255.255.255.0
2. Launch your web browser and enter the default IP address of your device in the address
field. IP Address
Pro Range products are pre-configured to IP address 192.168.0.229/192.168.0.228
If the unit has been reset, it will go to the default IP address of 192.168.1.1. You will need
to change your Ethernet adapter IP address to 192.168.1.x subnet.
3. Enter admin in the Username field and password in the Password field and click Login.
Pro Range User Manual Configuration 8
NAVIGATION
The Pro Range Configuration Interface contains four main tabs, each with sub tabs which
provide a web-based management page to configure a specific aspect of the SilverNet
device:
• Status The “Status Tab” displays device status, system logs, and real-time graphs.
• Admin The “Admin Tab” displays basic system properties, NTP configuration,
administration, SNMP configuration, LED Configuration, file and firmware management and
Reboot.
• Services The “Services Tab” allows you to configure Dynamic DNS.
• Network The “Network Tab” configures the network operating mode; This includes LAN
Interface settings, Wireless Settings, VLAN Management and Network Diagnostics.
• Logout The “Logout Tab” allows you to logout of the unit.
Apply Settings To apply any settings to the radio, click Save and Apply
Pro Range User Manual Status 9
STATUS
The Status tab displays a summary of the link status information, current values of the basic
configuration settings (depending on the operating mode), network settings and
information, and traffic statistics.
AP status page
Station status page
When using the alignment buzzer, the faster the beeps the better the signal quality.
Pro Range User Manual Status 10
OVERVIEW
Wireless This shows you the SSID, operating mode, channel frequency, bitrate, BSSID,
encryption mode and the DFS status.
Associated Stations Displays the MAC address, SSID and signal information of any stations
connected to the AP.
System Displays the name of the device, the firmware version and the current system date
and time. The date and time are displayed in DAY-MONTH-YEAR HOURS:MINUTES:SECONDS
format.
Memory Displays the total amount of memory on the board and shows how much is free in
kB (Kilobytes).
Network Displays local device information including the current uptime, MAC address and IP
address.
Wireless Parameters
SSID Displays the name of the wireless network that the AP is transmitting, the Service Set
Identifier (SSID), is what you will see if you scan with your laptop.
Mode This is “Master” if the device is set in AP mode or AP WDS Mode.
This will show as “client” if the device is in station mode or station WDS mode.
Channel Shows the channel number and frequency that the device is using.
Bitrate This is the maximum bitrate supported by the radio.
BSSID Displays the MAC address of the device.
Encryption Displays the wireless encryption used.
DFS Status If DFS is enabled, the device will automatically switch channels if any radar is
detected on the current channel it is using
Pro Range User Manual Status 11
Associated Stations Parameters
MAC Address Displays the MAC address of the device.
Network States the name of the wireless network.
Noise Displays the received noise power at the AP.
RSSI Displays the received signal strength.
TX Rate shows the transmit bitrate of the device.
RX Rate shows the receive bitrate of the device.
TX CCQ Displays the transmission quality in %. A higher percentage means better wireless
connection quality.
Up Time Displays the current uptime of the paired device.
Pro Range User Manual Status 12
REALTIME GRAPHS
There are four different graphs, you can view Load, Traffic, Wireless and connection graphs.
Pro Range User Manual Admin Tab 13
ADMIN TAB
The Admin tab contains administrative options. This page enables the administrator to
configure System Properties, Time Synchronisation, Logging Settings, User Management,
Web Administration, SNMP Configuration, LED Configuration, Backup config files / flash new
firmware and reboot the device.
SYSTEM
General Settings
Local Time Displays the local time according to the time zone.
Host Name Enter a name for your device.
Time Zone Select the correct time zone from the drop-down menu.
Sync with browser Click to sync device time with your browsers.
Time Synchronisation
Enable NTP Client Check to enable NTP.
Provide NTP Server Enter your preferred NTP Server under NTP candidates.
NTP Server Candidates These are the sources where you get your time information. We
recommend you enter at least three for accurate time synchronisation.
Pro Range User Manual Admin Tab 14
Logging
System Log Buffer Size Change the size of the log buffer.
External System Log Server Input an address that the system log is sent to.
External System Log Server Port Input an external server port.
Log Output Level Change the type of log report.
Cron Log Level Change the level of log report.
Pro Range User Manual Admin Tab 15
ADMINISTRATION
Use this section to change the administrator password.
Router Password
Password Enter a new password.
Confirmation Re-enter your new password.
Pro Range User Manual Admin Tab 16
SNMP
Simple Network Management Protocol (SNMP) is a popular protocol for network
management. It is used for collecting information from, and configuring, network devices on
an IP network.
SNMP Information
These identifiers are arbitrary and do not affect the server’s function, but they are useful to
have. The contact is the person who manages the server. The location is the server’s physical
location. Each of these parameters can be up to 64 characters.
SNMP Enterprise ID Enter the ID of the SNMP Server.
Contact Enter the name of the person who manages the server.
Location Enter the server’s physical location.
Pro Range User Manual Admin Tab 17
SNMP Configuration
Enable SNMP Enable SNMP
SNMP V2c Read Password Sets the community string for read-only access (to the carriables
on the SNMP agent) by the Network Management Station (NMS). The NMS is the software
that runs on the SNMP manager. (default: public)
SNMP V2c Write Password Sets the community string for read-write access by the SNMP
manager. (default: private) A community string identifies a group of SNMP agents. It is sent
in clear text. It should be changed from the default string “public” or “private”. The variables
on the SNMP agent can be classified into read-only or read-write variables.
SNMP V3 Username Sets the username for authentication. (default: admin)
SNMP V3 Auth Algorithm Shows the authentication algorithm used e.g. MD5.
SNMP V3 Auth Password Configures the password for user authentication. (default:
password)
SNMP V3 Privacy Algorithm Shows the data encryption algorithm used e.g. DES.
SNMP V3 Privacy Password Sets the password for data encryption. (default: password)
SNMP Trap
Enable SNMP Trap Allows the SNMP agent to notify the SNMP manager of events.
SNMP Trap IP Address Sets the IP address of the SNMP manager which receives the trap
messages.
SNMP Trap Port Sets the port number.
Pro Range User Manual Admin Tab 18
LED CONFIGURATION
You can configure the LEDs on the device to light up when received signal levels reach the
values defined in the four fields.
Signal Strength Indicator Interface Choose the wireless interface (wireless network name) to
display LEDs for.
Signal Strength Indicator LEDs Sets the received signal strength thresholds (in dBm), if the
signal is above the threshold, the LED will light up.
Pro Range User Manual Admin Tab 19
BACKUP/FLASH FIRMWARE
Backup / Restore
Download Backup Click to save down the configuration file of the device.
Reset to Defaults This will reset the device to the default factory settings (IP address
192.168.1.1)
Restore Backup Select the configuration file you wish to upload and click the restore button.
Add Functionality
Key File: Select the Key file you wish to upload to add extra functionality to the device.
Flash new firmware
Keep Settings Enable to keep the current settings after firmware upgrade.
Choose File Select the firmware file you wish to upgrade and click upload to begin the
update process.
Please be patient, as the firmware upgrade routine can take 5-10 minutes. The device will
be un-accessible until the firmware upgrade is completed.
Do not switch off the device! Do not reboot and do not disconnect the device from the
power supply during the firmware upgrade process as these actions will damage the
device!
REBOOT
Pro Range User Manual Admin Tab 20
Perform Reboot This option will perform a reboot of your device.
Pro Range User Manual Services 21
SERVICES
The Services tab provides useful and enhanced functions to help assist device operations.
DYNAMIC DNS
Dynamic DNS (DDNS) allows the device to be reached from the internet via a URL by
translating a URL like www.silvernet.com to an IP address like 206.190.36.45
Dynamic DNS Click this link to show information about the current DDNS version.
Hints
Show More Click this link to show hints on how to optimize your DDNS.
Overview
To global settings click here Click to access DDNS global settings.
Configuration Displays the DDNS Configuration Name.
Hostname/Domain Registered IP Displays the Hostname and Domains Registered IP.
Enabled Tick to enable / disable the DDNS configuration.
Last Update / Next Update Displays when the last DDNS update was / when the next DDNS
update is.
Process ID Start / Stop Click to start the DDNS Process ID.
Pro Range User Manual Services 22
Global Settings
Allow Non-public IP’s Tick to allow Non-Public IP Addresses.
Date Format Input date format code.
Status Directory Input device location of status directory.
Log Directory Input device location of log directory.
Log Length Number of lines stored in log files.
Pro Range User Manual Services 23
Add DDNS / Edit DDNS
Enabled Tick to enable specified DDNS section.
IP Address Version Choose which Internet Protocol version to use for your DDNS.
DDNS Service Provider [IPv4] Choose which DDNS service provider to use.
Custom Update-URL Input DDNS Update URL from DDNS provider.
Custom Update-Script Input custom DDNS update script for updating DDNS provider.
Hostname/Domain Input hostname / domain instead of typing into Custom Update-URL.
Username Input Username for custom update URL instead of typing into Custom Update-
URL.
Password Input Password for custom update URL instead of typing into Custom Update-URL.
Pro Range User Manual Services 24
Advanced Settings
IP Address Source [IPv4/6] Defines the source to read systems IPv4-Addresses from, that
will be sent to the DDNS provider.
Network [IPv4/6] Defines the interface to read systems IP Addresses from.
DNS-Server Input non-default DNS Server to detect registered IP Addresses.
PROXY-Server Input Proxy server for DDNS detection and updates.
Log to Syslog Specify which type of log to write to the system log.
Log to File Tick to enable detailed logging messages.
Pro Range User Manual Services 25
Timer Settings
Check Interval Specify interval to check for changed IP address.
Force Interval Specify interval to force updates from DDNS provider.
Error Retry Counter Specify number of attempts before DDNS script will stop execution.
Error Retry Interval Specify interval in which DDNS script will retry after Error Counter.
Pro Range User Manual Services 26
Log File Viewer
Read / Reread log file Click to display current system log file.
Pro Range User Manual Network Tab 27
NETWORK TAB
The Network tab contains everything needed to set up the networking part of the link. This
includes:
• LAN Interface: This allows you to configure the IP Address settings, DHCP Server
Settings, DNS Settings, Firewall Settings and Physical settings.
• Wireless Settings: This allows you to configure settings such as Country Codes,
Channel Selection, ACS Scanning, Antenna Gain, Transmit Power, Interface
Configuration, Wireless Security, MAC-filtering, Multipoint Enhancement Settings,
Distance Settings, Adaptive Noise Immunity, Chainmask Selection, Dynamic Channel
Selection.
• VLANs: This allows you to enable and manage VLANs.
Note Click the edit button to enter the set-up page for LAN or WLAN interface.
Pro Range User Manual Network Tab 28
LAN INTERFACE
General Setup
Protocol Here you can enable DHCP Client or Static (default)
DHCP Client If enabled, your device will get an IP address automatically from the
network. There must be a DHCP server configured on your network for this to function.
Static Allows you to enter a static IP address.
IPv4 Address Enter the IP address you wish to give to the device. You will use this IP address
to access the device interface.
IPv4 Netmask Enter the class for the IP address. The default is a class C value of
255.255.255.0
IPv4 Gateway (optional) Enter the gateway IP address of the network the device is
connected to.
IPv4 Broadcast (optional) Specifies the IPv4 broadcast address
Use Custom DNS Servers Enter the IP address for the DNS server you wish to use
Pro Range User Manual Network Tab 29
DHCP SERVER
DHCP Server disabled if ticked, un-tick to enable.
DHCP Server The device will act as a DHCP server hand out IP addresses automatically.
Start Specifies the lowest leased address to be issued
Limit Sets the maximum number of leased addresses
Leasetime States the expiry time of leased addresses
Dynamic DHCP Dynamically allocates DHCP addresses for clients. If disabled, only clients
having static leases will be served.
Force Forces DHCP on this network even if another server is detected
IPv4 Netmask Overrides the netmask sent to clients. Normally it is calculated from the
subnet that is served.
DHCP Options Defines additional DHCP options, for example "6, 192.168.2.1, 192.168.2.2"
which advertises different DNS servers to clients. Normally, connected devices would take
this board's IP address as the default gateway. To set an alternative default gateway, add the
DHCP option "3, 192.168.2.3" for example.
Pro Range User Manual Network Tab 30
Advanced Settings
Bring up on boot Tick to enable this interface on device boot.
Use built in IPv6-Management Tick to enable usage of built in IPv6 management for this
interface.
Override MAC Address Allows you to specify a different MAC address other than the routers
original one. This is useful if the ISP uses Mac addresses of routers to identify customers.
Override MTU Sets the maximum transmission unit (MTU), the default being 1500 bytes, we
recommend you do not change this unless your ISP requires you to.
Use Gateway Metric Allows you to specify a gateway metric. When a connected device must
choose from multiple gateways, the gateway with the smallest/lowest metric is chosen.
Pro Range User Manual Network Tab 31
Physical Settings
Bridge Interfaces Tick to enable bridging of ticked interfaces.
Enable STP Enables the Spanning Tree Protocol on this unit. This is disabled by default
The Spanning Tree Protocol (STP) is a network protocol. The main purpose of STP is to
ensure that you do not create loops when you have redundant paths in your network. Loops
are deadly to a network.
Interface List of all Interfaces and Adapters on device, tick to enable bridging between if
Bridge Interfaces is enabled.
Pro Range User Manual Network Tab 32
WIRELESS INTERFACE
Spectrum scans
Click the Scan button to perform a spectrum scan from the Station
This will show you a list detailing the channel number, MAC address and encryption method
of any devise nearby. You can click the “Join Network” button to connect to a specific AP.
From the Wireless Overview page, click the edit button to enter the wireless page
Pro Range User Manual Network Tab 33
DEVICE CONFIGURATION
Status This shows the current wireless connectivity of the device, similar to the “Status Tab”.
Wireless Network is Enabled Enabled by default, click to disable wireless interface.
Country Code Each country has their own power level and frequency regulations. To ensure
the device operates under the necessary regulatory compliance rules, you must select the
country where your device will be used. The IEEE 802.11 mode, channel and frequency
settings, and output power limits will be tuned according to the regulations of the selected
country.
Mode Choose what throughput speeds to limit the wireless communication to. This can be
upgraded via License Keys to 866Mbps.
Channel Spectrum Width Displays the spectral width of the radio channel. You can use this
option to control the bandwidth consumed by your link. Using higher Channel width
increases throughput. Using lower Channel width reduces throughput.
Pro Range User Manual Network Tab 34
Channel widths available are 5 MHz, 10 MHz, 20 MHz, and 40 MHz
When the 802.11ac wireless standard is used, the 80 MHz band can be selected. An 80 MHz
band can carry twice the amount of data of a 40 MHz band.
Frequency The default, Auto, allows the device to automatically select the frequency. You
can specify a frequency from the drop-down list. The frequency range available depends on
the country you select in Country Code. Some countries have DFS regulations which may
affect and delay the device when attempting to establish a connection. It can take up to 30
minutes to connect.
Block DFS Channel List Tick to block selection of DFS channels to avoid DFS radar
interference.
Background ACS Scan / ACS Scan Interval This will allow the device to automatically scan
and switch to a better channel after a period of time when no client is connected. Default
time for the scan is every 60 seconds.
ACS provides an easy way to optimise channel arrangement. It provides an optimal solution
only if it is used on all APs in a site. Using ACS on a single AP provides a useful but sub-
optimal solution. Once an AP has selected a channel, it remains operating on that channel
until the user changes the channel or it scans again (after a reboot). The best way to make
the AP always choose the best channel is to enable Dynamic Channel Selection (see below)
Antenna Gain Represents the gain relative to an isotropic antenna. A higher antenna gain
results in the transmit power more focused towards a certain direction. You can set this
depending on the antenna you have, e.g. PICO 12dBi, MICRO 15dBi, LITE 18dBi, MAX 25dBi.
When country code is set, the value of the antenna gain will be considered to limit the
selectable transmit power, such that the EIRP limits of the country are satisfied.
Transmit Power The maximum transmit power displayed is determined by the country code
and the maximum transmit power of the radio.
Pro Range User Manual Network Tab 35
5MHz and 10MHz Channel Spectrum Width
From the Channel Spectrum Width drop down list, choose 20MHz. A new setting will appear,
Channel Bandwidth Used. Select either 20MHz, 10MHz or 5MHz from this new drop-down
menu.
Click Save & Apply to save the configuration.
Using higher bandwidth increases throughput. Using lower bandwidth reduces throughput.
Channel widths available are:
5 MHz – TX 32 – 20/25Mbps
10 MHz – TX 65 – 40/45Mbps
20 MHz – TX 130 – 90/95Mbps
20/40 MHz – TX 300 – 90/95Mbps – Both ways
Pro Range User Manual Network Tab 36
Advanced settings
Link Distance Specifies the distance between the AP and the station if the previous option is
unchecked. Min: 300, Max: 24000 (40MHz), 48000 (20MHz). This value should be set to
slightly more than the physical distance between the AP and the farthest station. Leave
blank for auto.
Adaptive Noise Immunity Check to enable. When enabled, it automatically adjusts the
signal/noise level for best performance. In a low noise environment, it is recommended you
turn off this function.
Dynamic Channel Selection This is a feature to monitor traffic and noise levels. If the noise
levels exceed the threshold, the AP will disconnect any associated stations and move to a
new channel. The stations are expected to re-associate with the AP on their own. Available
selections are:
• Look for CW Interference Use this feature to detect and avoid continuous wave
(CW) interference.
• Look for WLAN Interference Use this feature to detect and avoid wireless
interference
• Look for CW and WLAN Interference Use this feature to detect and avoid
continuous wave (CW) interference and Wireless interference.
Pro Range User Manual Network Tab 37
Interface Configuration
ESSID If the device is operating in Access Point or Access point WDS mode, specify the
wireless network name or SSID (Service Set Identifier) used to identify your WLAN. All the
client devices within range will receive broadcast messages from the AP advertising this
SSID. If the device is operating in Station mode, specify the SSID of the AP the device is to
connect to.
Mode Displays the operating mode of the radio interface. The Pro Range supports four
operating modes:
• Station
• Station WDS
• Access Point
• Access Point WDS
Station If you have a client device to connect to an AP, configure the client device as Station
mode.
The SSID of the AP is used, and it forwards all the traffic to/from the network devices to the
Ethernet interface. This mode translates all the packets that pass through to its own MAC
address, thus resulting in a lack of transparency.
Station WDS This mode is used to create a transparent bridge and can be connected to a
device running in Access Point WDS mode. Multiple stations or Stations WDS can connect to
an AP WDS.
Access Point If you have a single device to act as an AP, configure it as Access Point mode.
The device functions as an AP that connects multiple client devices
Access Point WDS This mode connects to a device running Station WDS mode. It is used to
create a transparent bridge.
In most cases, we recommend that you use WDS because it enables transparent Layer 2
traffic. The WDS protocol is not defined as a standard, so there may be compatibility issues
between equipment from different vendors.
Pro Range User Manual Network Tab 38
Guard Interval This is the space between symbols being transmitted. The Guard Interval is
there to eliminate inter-symbol interference. For long distance connections, select Long to
give better performance.
Data Rate Data Rates consist of both the legacy rates and the MCS (Modulation Coding
Scheme – Only for 802.11n) rates.
6 – 54Mbps are Legacy Rates
MCSO to MCS7 are 802.11n rates
The MCS settings have different rates depending on the Chainmask Selection (see above for
Chainmask Selection) that is used.
Chainmask Selection
1x1
2x2
MCS0
13.5Mbps
27Mbps
MCS1
27Mbps
54Mbps
MCS2
40.5Mbps
81Mbps
MCS3
54Mbps
108Mbps
MCS4
81Mbps
162Mbps
MCS5
108Mbps
216Mbps
MCS6
121.5Mbps
243Mbps
MCS7
135Mbps
300Mbps
When left on auto the data rate will follow an advanced rate algorithm that considers the
number of errors at that data rate and fine tunes to the best data rate it can use.
Hide SSID Once checked, this will disable advertising the SSID of the access point in
broadcast messages to wireless stations. This option is only available in Access Point and
Access Point WDS mode.
Pro Range User Manual Network Tab 39
WIRELESS SECURITY
All the wireless security settings are set under this section.
The operation of the Keys is the same for ALL the Wireless modes.
Security The Pro 95 range supports the following wireless security methods:
No Encryption If you want an open network without wireless security, select No Encryption.
WEP Open System WEP (Wired Equivalent Privacy) is the oldest and least secure security
algorithm.
WEP Shared Key WEP (Wired Equivalent Privacy) with slightly better authentication.
WPA-PSK WPA (Wi-Fi Protected Access) was developed as a stronger encryption method
than WEP. This uses TKIP Temporal Key Integrity Protocol which uses RC4 encryption
algorithm.
WPA2-PSK WPA2 was developed to strengthen wireless encryption security and is stronger
than WEP and WPA. This is the most secure option. It uses the latest Wi-Fi encryption
standard, and the latest AES (Advanced Encryption Standard) encryption protocol.
WPA2-PSK AES+ As above but with 256bit encryption.
WPA-PSK/WPA2-PSK Mixed Mode This enables both WPA and WPA2 with both TKIP and
AES. This provides maximum compatibility with any ancient devices you might have.
IEEE802.1X/WPA-EAP This will require the equipment to be authenticated via a RADIUS
server. The RADIUS server must support EAP or be chained/proxied to one that does.
IEEE802.1X/WPA2-EAP This will require the equipment to be authenticated via a RADIUS
server. The RADIUS server must support EAP or be chained/proxied to one that does.
Pro Range User Manual Network Tab 40
WEP
Note: Operating with WEP security will limit AP to maximum wireless link speed of
54Mbps only.
Encryption Select the type of encryption you want to use.
Open System (Default) No authentication. We recommend using this option over shared
authentication.
Shared Key May not be compatible with all Access Points. Not recommended.
Used Key Slot Select which key to use
Key #1 Enter a security key to use
Key #2 Enter a security key to use
Key #3 Enter a security key to use
Key #4 Enter a security key to use
WPA/WPA2 Authentication
The configuration options are the same for WPA and WPA2 authentication. WPA2-PSK is the
strongest security method. If all wireless devices on your network support this option, we
recommend that you select it.
Cipher Specify which of the following to use:
• Auto – Uses the most appropriate algorithm for the network
• CCMP (AES) - Advanced Encryption Standard (AES) algorithm. (default)
• TKIP and CCMP (AES) - Temporal Key Integrity Protocol which uses RC4 encryption
algorithm and Advanced Encryption Standard (AES) algorithm.
•
Key The key is an alpha-numeric password between 8 and 63 characters long.
Pro Range User Manual Network Tab 41
MAC-Filter
This setting is only available on the Access Point.
MAC-Address Filter Lets you allow only devices with the listed MAC address to associate
with this AP, or lets you block devices with the listed MAC address.
Mac List Adds the MAC address of the remote device to either block or allow.
Advanced Settings
Station Isolation When checked, it prevents station-to-station communication. When
Station Isolation is disabled, wireless clients can communicate with one another normally by
sending traffic through the AP. When Station Isolation is enabled, the AP blocks
communication between wireless clients on the same AP.
Block VLAN Passthrough Tick to block VLAN traffic from passing across the link.
RTS/CTS Threshold This value is set to 2346 as default, which is the maximum 802.11 packet
size. We recommend leaving this setting for Point-to-Point links, however, for Multipoint
setups we recommend setting the RTS Threshold lower (538). The AP device sends Request
to Send (RTS) frames to a receiving station and negotiates the sending of a data frame. After
receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to
acknowledge the right to begin transmission. The CTS contains a hold off time that prevents
other clients from sending anything whilst the targeted client sends its data. Setting the RTS
lower will improve the stability of a Multipoint setup.
Minimum Received Signal Input a numeric value in dB for the minimum allowed SNR to
establish a link.
Pro Range User Manual Network Tab 42
WMM Mode Provides Quality of Service (QoS) features. This is checked by default. Wireless
multimedia (WMM) enables the classification of the network traffic into 4 main types, voice,
video, best effort, and background, in decreasing order of priority. Higher priority traffic has
a higher transmission opportunity and would have to wait less time to transmit. As a result,
an existing video stream would not be interrupted by additional background processes.
VLANS
The VLANS tab contains everything needed to set up VLANS.
Enable VLAN Functionality Check to enable VLANS
Pro Range User Manual Network Tab 43
VLAN Entries
VLAN ID Enter the VLAN ID you wish to use
CPU Choose to leave off, or Tag or Untag the Ethernet interface
Port 1 Choose to leave off, or Tag or Untag the Port 1 interface
Port 2 Choose to leave off, or Tag or Untag the Port 2 interface
Port 3 Choose to leave off, or Tag or Untag the Port 3 interface
Port 4 Choose to leave off, or Tag or Untag the Port 4 interface
Port 5 Choose to leave off, or Tag or Untag the Wireless interface
Port 6 Choose to leave off, or Tag or Untag the Port 6 interface
Delete Delete the VLAN
Pro Range User Manual Network Tab 44
DIAGNOSTICS
Use this page to perform some basic network diagnostic tests, such as Ping, Traceroute and
Nslookup.
Ping Enter an address to Ping, as well as the Internet Protocol Type. Ping is a command-line
utility that acts as a test to see if a networked device is reachable. The ping command sends
a small amount of data over the network to a specific device and measures the round-trip
time to receive a response.
Traceroute Enter an address to traceroute. Traceroute is a diagnostic command for
displaying possible routes and measuring transit delays of packets across a network. The
history of the route is recorded as the round-trip times of the packets received from each
successive host in the route; the sum of the mean times in each hop is a measure of the total
time spent to establish the connection. Traceroute proceeds unless all (usually three) sent
packets are lost more than twice; then the connection is lost and the route cannot be
evaluated.
Nslookup Enter an address to query. Nslookup is a network administration command-line
tool for querying the DNS to obtain domain name or IP address mapping, or other DNS
records.
Pro Range User Manual Standards 45
STANDARDS
DECLARATION OF CONFORMITY
SilverNet Limited declares the following:
Product Name: PRO Range GEN4
Model No.: PICO, MICRO, LITE, MAX conforms to the following Product Standards:
This device complies with the Electromagnetic Compatibility Directive (89/336/EEC) issued
by the Commission of the European Community. Compliance with this directive implies
conformity to the following European Norms (in brackets are the equivalent international
standards.)
Electromagnetic Interference (Conduction and Radiation): EN 55022 (CISPR 22)
Electromagnetic Immunity: EN 55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11)
Low Voltage Directive: EN 60 950: 1992+A1: 1993+A2: 1993+A3: 1995+A4: 1996+A11: 1997.
Therefore, this product is in conformity with the following regional standards:
FCC Class B: following the provisions of FCC Part 15 directive,
CE Mark: following the provisions of the EC directive.
SilverNet Limited also declares that:
The wireless card in this product complies with the R&TTE Directive (1999/5/EC) issued by
the Commission of the European Community. Compliance with this directive implies
conformity to the following:
EMC Standards: FCC: 47 CFR Part 15, Subpart B, 47 CFR Part 15, Subpart C (Section 15.247);
CE: EN 300 328-2, EN 300 826 (EN 301 489-17)
Therefore, this product is in conformity with the following regional standards:
FCC Class B: following the provisions of FCC Part 15 directive,
CE Mark: following the provisions of the EC directive.
Pro Range User Manual Warnings 46
WARNINGS
RADIO FREQUENCY INTERFERENCE REQUIREMENTS
The operation of this device in the 5.15 GHz to 5.25 GHz frequency range is restricted to
indoor use. FCC regulations require this product to be used indoors while operating at 5.15
GHz to 5.25 GHz to reduce the potential for harmful interference. However, the operation of
this device in the 5.25 GHz to 5.35 GHz frequency range is allowed for both indoor and
outdoor use. High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz
and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or
damage to this device.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
No guarantee exists that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception (determined by
turning the equipment off and on), the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the radio/TV receiving antenna.
• Increase the separation between the equipment and the radio/TV receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
radio/TV receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. Modifications
made to the product, unless expressly approved by SilverNet Limited, could void the
user’s authority to operate the equipment.
RF Exposure Requirements
To ensure compliance with FCC RF exposure requirements, the antenna used for this device
must be installed to provide a separation distance of at least 20 cm from all persons and
must not be co-located or operating in conjunction with any other antenna or radio
transmitter. Installers and end-users must follow the installation instructions provided in this
user guide.
Pro Range User Manual Warnings 47
CE Statement
The PRO Range GEN4 is intended to be used by suitably trained individuals or organisations
that are familiar with the requirements of the R&TTE directive. In particular the client must
ensure that appropriate antennas and transmit power levels are selected to ensure that all
power limits are met. Hereby, SilverNet Limited declares that this device is in compliance
with the essential requirements and other relevant provisions of the R&TTE Directive
1999/5/EC. However, the use of the following warning symbol
Means that this equipment is subject to restrictions of use in certain countries and selection
of the correct country of operation (country code) will ensure that the device operates only
on the frequencies permissible within that country. It is also the operator’s responsibility to
ensure that appropriate licenses have been sought when operating on licensed frequencies,
for example UK Band C, 5725-5850MHz.
In the UK, all radios operate under the control of Ofcom. Radio use in the 2.4 & 5GHz bands
are deemed to be Licence Exempt with the exception of Band C. Band C (5.725 to 5.825GHz)
requires registration with Ofcom under a light licensing scheme. While this band is still
effectively licence exempt, Ofcom wants to keep a register of all FWA links and charges a
small fee. Any user wishing to set up an outdoor link for FWA needs to apply to Ofcom for a
site license; the licence is not hard to obtain and is only £50 which includes registration of up
to 50 terminals. For every terminal beyond 50 you should add £1 to the cost of your licence.
Further information on the legal implications of Band C usage can be found on the Ofcom
website.
Pro Range User Manual Troubleshooting 48
TROUBLESHOOTING
If you are having problems with your links, then please check the following before calling our
support team.
Line of Sight The radios work best when they have line-of-sight. If the radios do not have
line-of-sight, then you will get a very poor signal or no signal at all.
Alignment If the radios are not correctly aligned the signal quality of the radios will suffer
and you may not receive the throughput you require. Run SilverView and use the data test
tool.
Power If the units are not powering on then you will need to test the Ethernet cable and re-
terminate it if required. We recommend outdoor shielded grade cable for all installations.
Please also check that the PSU is plugged in and turned on.
Interference Our radios use auto-channel select and should avoid interferences as best as
possible. Rebooting the radios will allow a re-scan. If you are experiencing interference
problems when using the radios, try setting them on a static channel. Try each channel until
you find one that gives you a better signal. Use SilverView and run a data test.
WARRANTY
The PRO Range GEN4 comes with a 2-year warranty as standard. For full terms and
conditions of warranty please go to www.silvernet.com/terms-and-conditions/
CONTACT SILVERNET
Email us at support@silvernet.com
Call our support team on 08712233067
www.silvernet.com
COPYRIGHT INFORMATION
Copyright ©2021 all rights reserved. No part of this publication may be reproduced,
adapted, stored in a retrieval system, translated into any language, or transmitted in any
form or by any means without the written permission of the supplier.
Pro Range User Manual Other SilverNet Products 49
OTHER SILVERNET PRODUCTS
PRO RANGE
INDUSTRIAL NETWORK TRANSMISSION
INTELLIGENT WI-FI SOLUTIONS
INDUSTRY LEADING TECHNICAL SUPPORT